2002 Toyota Prius Owners Manual

4. Airbag sensor assembly 5. Airbag module for driver (airbag and

inflator)

The airbag sensor assembly consists of a safing sensor and airbag sensor.

In a severe frontal impact, the sensors detect deceleration and the system trig- gers the airbag inflators. At this time a chemical reaction in the inflators quickly fills the airbags with non–toxic gas to help restrain the forward motion of the occu- pants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non–toxic gas. This does not indicate a fire. This gas is nor- mally harmless; however, for those who have delicate skin, it may cause a minor skin irritation. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Parts of the airbag module (steering wheel hub, dashboard) may be hot for several minutes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.

Hitting a curb, edge of pavement or hard material

22p016b

Falling into or jump- ing over a deep hole

Landing hard or vehicle falling

The SRS front airbags may deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

50

the windshield as

A crash severe enough to inflate the air- bags may break the vehicle buckles. In vehicles with a pas- senger airbag the windshield may also be damaged by absorbing some of the force of the inflating airbag.

CAUTION

(cid:1) The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver side and front passenger side seat belt sys- tems. The front seat occupants can be killed or seriously injured by the inflating airbags if they do not wear the available seat belts properly. During sudden braking just before a collision, an unrestrained driver or front passenger can move for- ward into direct contact with or close proximity to the airbag which may then deploy during the colli- sion. To ensure maximum protection in an accident, the driver and all passengers the vehicle must wear their seat belts properly. Wear- ing a seat belt during an accident reduces the chances of death or serious injury or being thrown out of the vehicle. For instructions and precautions concerning the seat belt system, see “Seat belts—” on page 40 in this section.

in

restraint

(cid:1) Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing front airbags. An infant or child who is too small to use a seat belt should be properly secured using a child Toyota strongly recommends in- fants and children be placed in the rear seat of the vehicle and proper- ly restrained. The rear seat is the safest for infants and children. For instructions concerning the installa- tion of a child restraint system, see “Child restraint—” on page 61 in this section.

that all

system.

51

(cid:1) For

instructions concerning

the installation of a child restraint sys- tem, see “Child restraint—” on page 61 in this section.

22p018a

22p019

Move seat fully back

(cid:1) Never put a rear–facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.

52

(cid:1) A

forward–facing child

restraint system should be allowed to be put on the front seat only when it is unavoidable. Always move the seat as far back as possible, because the force of the deploying front air- bag could cause death or serious injury to the child.

(cid:1) On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbag inflates, because impact could cause death or serious injury to the child.

the

22p020a

22p021a

22p022b

is

in use, since

(cid:1) Do not sit on the edge of the seat lean over the dashboard when or the vehicle the front airbags inflate with consider- able speed and force. Otherwise, you may be killed or seriously in- jured. Sit up straight and well back in the seat, and always use your seat belt properly.

the

(cid:1) Do not allow a child to stand up or to kneel on front passenger seat, since the front airbag inflates with considerable speed and force. Otherwise, the child may be killed or seriously injured.

(cid:1) Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint—” on page 61 in this sec- tion.

(cid:1) Do not put objects or your pets on or in front of the dashboard or steering wheel pad that houses the front airbag system. They might re- strict inflation or cause death or serious injury as they are projected rearward by the force of deploying airbags. Likewise, the driver and front passenger should not hold ob- jects their knees.

their arms or on

in

53

(cid:1) Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components, such as the steering wheel pad, steering wheel, column cover, front passen- ger airbag cover, front passenger airbag or airbag sensor assembly. Doing any of these may cause sud- den SRS front airbag inflation or disable the system, which could re- sult in death or serious injury.

instructions Failure to follow these can result in death or serious injury.

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can in- terfere with proper operation of the SRS front airbag system in some cases. (cid:2) Installation of electronic devices such as a mobile two–way radio, cassette tape player or compact disc player

(cid:2) Modification of the suspension sys-

tem

(cid:2) Modification of the front end struc-

ture

(cid:2) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

(cid:2) Repairs made on or near the front fenders, front end structure, con- sole, steering column, steering wheel or dashboard near the front passenger airbag

22p010

This SRS front airbag system has a ser- vice reminder indicator to inform the driver of operating problems. If either of the fol- lowing conditions occurs, this indicates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to ser- vice the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on.

(cid:1) The light comes on while driving.

54

SRS side airbags

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

22p023a

22p024a

In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The SRS front airbags have been in-

flated.

(cid:1) The front of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS front airbags to inflate.

(cid:1) The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.

passenger

airbag

front

The SRS (Supplemental Restraint Sys- tem) side airbags are designed to pro- vide further protection for the driver and front passenger in addition to the primary safety protection provided by the seat belts. In response to a severe side impact, the SRS side airbags work together with the seat belts to help reduce injury by inflat- ing. The SRS side airbags help to reduce injuries mainly to the driver’s or front pas- senger’s chest. The SRS side airbag on the passenger seat is activated even with no passenger in the front seat. Be sure to wear your seat belt properly.

55

Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seat belt restraint system by the driver and passenger when the SRS side airbags are inflated.

CAUTION

SRS side airbags inflate with consid- erable force. To avoid potential death or serious injury when they inflate, the driver and front passenger must: (cid:1) Wear their seat belts properly. (cid:1) Remain properly seated with their back upright and against the seat at all times.

56

22p010

22p025

This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the SRS side airbags are operating properly. The warning light system monitors the air- bag sensor assembly, front airbag sen- sors, side airbag sensors, front seat belt pretensioner assemblies, warning light, in- terconnecting wiring and power sources. (For details, see “Service reminder indica- tors and warning buzzers” on page 91 in Section 2–4.)

from

The SRS side airbag system may not inflate if the vehicle is subjected to a collision the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment as shown in the illustra- tion. The SRS side airbags are designed to inflate when the passenger compartment area suffers a severe the side. For the safety of all occupants, always wear your seat belts properly.

impact

from

Collision from the rear

22p026b

22p027

Collision from the front

Vehicle rollover

The SRS side airbags are not designed to inflate if the vehicle is involved in a front or rear collision, if it rolls over, or if it is involved in a low–speed side collision.

The SRS side airbag system consists mainly of the following components, and their locations are shown in the illustra- tion. 1. SRS warning light 2. Side airbag modules

(airbag and inflator) 3. Side airbag sensors 4. Airbag sensor assembly The SRS side airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sen- sor and airbag sensor.

In a severe side impact, the side airbag sensor triggers the side airbag inflators. Then a chemical reaction in the inflators quickly fills the airbags with non–toxic gas to help restrain the lateral motion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non–toxic gas. This does not indicate a fire. This gas is nor- mally harmless; however, for those who have delicate skin, it may cause a minor skin irritation. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation. Deployment of the airbags happen in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Front seats may be hot for several min- utes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.

57

CAUTION

(cid:1) The SRS side airbag system is de- signed only as a supplement to the primary protection of the driver side and front passenger side seat belt systems. To ensure maximum protection in an accident, the driver and all passengers in the vehicle must wear their seat belts properly. Wearing a seat belt properly during an accident reduces the chances of death or serious injury or being thrown out of the vehicle. For in- structions and precautions concern- ing the seat belt system, see “Seat belts” on page 40 in this section.

58

restraint

(cid:1) Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing airbags. An infant or child who is too small to use a seat belt should be properly secured using a child Toyota strongly recommends in- fants and children be placed in the rear seat of the vehicle and proper- ly restrained. The rear seat is the safest for infants and children. For instructions concerning the installa- tion of a child restraint system, see “Child restraint” on page 61 in this section.

that all

system.

if he/she

(cid:1) Do not allow a child to lean his/her head or any part of his/her body against the front door or the area of the seat from which the side air- bag deploys even is seated in the child restraint system. It is dangerous if the side airbag inflates, and the impact could cause death or serious injury to the child. For the installation of a child restraint sys- tem, see “Child restraint” on page 61 in this section.

instructions concerning

22p028b

(cid:1) Do not lean against the front door when the vehicle is in use, since the side airbag inflates with consid- erable speed and force. Otherwise, you may be killed or seriously in- jured.

(cid:1) Sit up straight and well back in the seat, distributing your weight even- ly in the seat. Do not apply exces- sive weight to the outer side of the front seats on vehicles with side airbags.

for

(cid:1) Do not use accessories

the seats which cover the parts where the side airbags inflate. Such acces- sories may prevent the side airbags from activating correctly, causing death or serious injury.

(cid:1) Do not modify or replace the seats or upholstery of front seats with the side airbags. Such changes may disable the system or cause the side airbags to inflate accidentally, resulting in death or serious injury. Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repairs and modifications.

22p029c

(cid:1) Do not attach a cup holder or any other device or object on or around the door. When the side airbag in- flates, the cup holder or any other device or object will be thrown with great force or the side airbag may not activate correctly, resulting in injury. Likewise, death or serious the driver and front passenger should not hold objects their arms or on their knees.

in

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the SRS side airbag system in some cases. (cid:2) Installation of electronic devices such as a mobile two–way radio, cassette tape player or compact disc player

(cid:2) Modification of the suspension sys-

tem

(cid:2) Modification of the side structure of

the passenger compartment

(cid:2) Repairs made on or near the con-

sole or front seat

59

22p010

22p030e

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

This SRS side airbag system has a ser- vice reminder indicator to inform the driver of operating problems. If either of the fol- lowing conditions occurs, this indicates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to ser- vice the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on. (cid:1) The light comes on or flashes while

driving.

60

In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The SRS side airbags have been in-

flated.

(cid:1) The portion of the doors (shaded in the illustration) were involved in an acci- dent that was not severe enough to cause the SRS side airbags to inflate. (cid:1) The surface of the seats with the side airbag (shaded is scratched, cracked, or otherwise dam- aged.

illustration)

the

in

Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all 50 states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts–” on page 40 for details.

CAUTION

(cid:1) For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.

(cid:1) Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, and is put on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. (cid:1) Never put a rear–facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear–facing child restraint system is put on the front seat.

(cid:1) Unless it is unavoidable, do not put the

restraint system on

a child front seat.

(cid:1) A

forward–facing child

restraint system should be allowed to put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of the deploying airbag could cause death or serious injury to the child.

(cid:1) On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbag inflates, and the impact could cause death or serious injury to the child.

(cid:1) Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly se- cured.

61

—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap por- tion of the lap/shoulder belt. You must carefully consult the manufacturer’s in- structions which accompany child re- straint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following instructions. The child restraint system should be installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.

62

CAUTION

(cid:1) Never put a rear–facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear–facing child restraint system is put on the front seat.

(cid:1) Unless it is unavoidable, do not put the

restraint system on

a child front seat.

(cid:1) A

forward–facing child

restraint system should be allowed to put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of the deploying airbag could cause death or serious injury to the child.

(cid:1) On vehicles with side airbag, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbag inflates, and the impact could cause death or serious injury to the child.

(cid:1) After

installing the child restraint system, make sure it is secured in place following the manufacturer’s instructions. If it is not restrained securely, it may cause death or se- rious the event of a sudden stop or accident.

the child

injury

to

in

When not using the child restraint system, keep it secured with the seat belt or place it in the trunk or somewhere other than in the passenger compartment. This will pre- vent the event of a sudden stop or accident. For instructions about how to use the an- chor bracket, see “—Using a top strap” on page 72 in this section.

injuring passengers

from

in

it

—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Child restraint lower anchorages approved for your vehicle may also be used. See “—Installation with child restraint lower an- chorages” on page 74 in this section.

22p031a

22p033a

(A) Infant seat

(C) Booster seat

22p032a

(B) Convertible seat

63

—Installation with 3–point type seat belt

22p034a

22p035a

22p045c

(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.

CAUTION

(cid:1) Never put a rear–facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.

64

(cid:1) Do not put a rear–facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause death or serious injury to the child and front passenger in case of sud- den braking or a collision.

(cid:1) If the driver’s seat position does not allow sufficient space for safe installation, re- straint system on the rear left seat.

the child

install

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the child restraint system until the seat belt is fixed.

from

22p037a

1. Run the lap and shoulder belt through or around the baby seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

22p038a

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

65

22p039a

22p040a

22p041b

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the baby seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

66

22p042a

22p043a

22p044

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward– facing or rear–facing position depend- ing on the child’s age and size. When installing, follow the manufacturer’s in- struction about the applicable child’s age and size as well as directions for installing the child restraint system.

CAUTION

(cid:1) Never put a rear–facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.

Move seat fully back

(cid:1) A forward–facing child restraint sys- tem should be allowed to be put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of the deploying airbag could cause death or serious injury to the child.

(cid:1) On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbag inflates, and the impact could cause death or serious injury to the child.

67

22p036d

22p046a

CAUTION

(cid:1) Do not put a rear–facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause death or serious injury to the child and front passenger in case of sud- den braking or a collision.

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the child restraint system until the seat belt is fixed.

from

(cid:1) If the driver’s seat position does not allow sufficient space for safe installation, re- straint system on the rear left seat.

the child

install

68

22p047a

22p048a

22p049a

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

69

22p050a

22p051a

22p052

Move seat fully back

4. To remove the convertible seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward–fac- ing position only.

70

CAUTION

(cid:1) A

forward–facing child

restraint system should be allowed to be put on the front seat only when it is unavoidable. Always move the seat as far back as possible, because the force of the deploying airbag could cause death or serious injury to the child.

(cid:1) On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbag inflates, and the impact could cause death or serious injury to the child.

22p053a

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.

insert

the

tab

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts—” on page 40 for details.

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.

to do so could reduce

(cid:1) Both high–positioned lap belts and loose–fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on a child’s hips as possible.

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

71

(cid:1) If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the child restraint system until the seat belt is fixed.

from

—Using a top strap

22p054a

22p055

2. To remove the child restraint system, the buckle–release button and

press allow the belt to retract.

Follow the procedure below for a child restraint system that requires the use of a top strap.

72

Anchor brackets

22p056c

22p063a

22p064c

Use the anchor bracket on the package tray behind the rear seat to attach the top strap. Anchor brackets are rear seating position.

for each

installed

TO USE THE ANCHOR BRACKET: 1. Outside anchor brackets only—

Remove the head restraint.

2. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint—” on page 61 in this section.

install

to

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions.

73

—Installation with child restraint lower anchorages

22p065a

22p076c

3. Outside anchor brackets only—

Replace the head restraint.

74

22p077d

interfaced with

The lower anchorages for the child re- straint system the FMVSS225 specification are installed in the rear seat. The anchorages are installed in the clear- ance between the seat cushion and seat- back of both outside rear seats. Child restraint system interfaced with the FMVSS225 specification can be fixed with these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

Type A

CHILD RESTRAINT SYSTEM INSTALLA- TION Type A— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages below the tag in the seatback.

2. Latch the hooks of lower straps onto the anchorages and tighten the lower straps. Type B— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages below the tag in the seatback.

2. Latch the buckles onto the anchor-

ages

CAUTION

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

(cid:1) Do not put a child restraint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause death or se- vere injury to the child and front passenger in case of sudden brak- ing or a collision.

it should be anchored. (For

If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 72 in this section.) For to the instruction manual equipped with each product.

the installation details, refer

75

22p078d

Type B

Tilt steering wheel

Outside rear view mirrors—

22p058d

CAUTION

(cid:1) Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

22p059

release

To change the steering wheel angle, hold the steering wheel, push down the lock the steering wheel to the desired angle and push the lever up to lock the steering wheel in position.

lever,

tilt

76

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

—Power rear view mirror control

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

22p060c

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de–icer to free the mirror.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch at “L” (left) or “R”

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

The mirrors can be adjusted when the key is in the “ACC” or “ON” position.

77

—Folding rear view mirrors

Anti–glare inside rear view mirror

22p066

22p061

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

for parking

The rear view mirrors can be folded backward restricted areas. To fold the rear view mirror, push back- ward.

in

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

78

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

Vanity mirror

22p062a

To use the vanity mirror, swing down the sun visor and open the cover.

79

80

SECTION 2– 3

OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flasherss Instrument panel light control Interior light Personal light Windshield wipers and washer Rear window defogger

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

82
83
84
84
85
85
86

81

The lights automatically turn off when the driver’s door is opened with the ignition turned off. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the head- light switch is off. When the headlight switch is turned to the first or second clickstop, the brightness of the reduced slightly unless the instrument panel light control dial is turned fully on.

instrument cluster will be

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on longer than necessary when the hy- brid system is not running.

Daytime running light system The headlights turn on at reduced intensi- ty when the parking brake is released with the hybrid system started, even with the light switch in the ”OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.

Headlights and turn signals

23p001a

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Vehicles sold in U.S.A.: When the head- lights are on, the headlight indicator lights up in the instrument cluster. Vehicles sold in Canada: When the tail lights are on, the tail light indicator lights up in the instrument cluster.

the

82

Emergency flashers

23p003a

23p004a

23p005

High–Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights even with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs—” on page 225 in Section 8–3.

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

83

NOTICE

To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the hy- brid system is not running.

Instrument panel light control

Interior light

23p006c

23p007c

To adjust the brightness of the instru- ment panel lights, turn the dial. When the headlight switch is turned to the first or second clickstop, the brightness of the reduced slightly unless the instrument panel light control dial is turned fully on.

instrument cluster will be

To turn on the interior light, slide the switch. The interior light switch has the following positions: ”ON”—Keeps the light on all the time. ”OFF”—Turns the light off. ”DOOR”—Turns the light on when any of the door is opened. The light remains on for 15 seconds when all the doors are closed. ILLUMINATED ENTRY SYSTEM With the switch in “DOOR” position, the light comes on when either door is opened. After all the doors are closed, the light remains on for about 15 seconds and then fades out.

84

However, in the following cases, the light goes off immediately. (cid:1) All the doors are closed when the igni- tion key is in “ACC” or “ON” position.

(cid:1) All the doors are closed and locked. When all the doors are unlocked with a key or wireless remote control simulta- neously, the light comes on for about 15
seconds and then fade out, even if the door is not opened.

Personal light

Windshield wipers and washer

23P012b

23p008b

To turn on the personal light, push the switch. To turn it off, push the switch again.

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Position 1
Position 2
Position 3

Speed setting Intermittent

Slow Fast

The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it.

the band upward to

85

Make sure you turn the defogger off when the window is clear. Leaving the defogger on for a long time could cause the auxilia- ry battery to discharge. The defogger is not designed for drying rain water or for melting snow.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

To squirt washer fluid, pull the lever toward you and release it. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 225 in Section 8–3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

Rear window defogger

23p009

To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the surface. An indicator light will illuminate to indicate the defogger is operating. Push the switch once again to turn the defogger off. The system will automatically shut off af- ter the defogger has operated about 15
minutes.

86

SECTION 2– 4

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge Coolant temperature indicator and warning lightt Odometer and two trip meters Switching km/h MPH button Service reminder indicators and warning buzzers

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

88
89
90
91
91

87

Low fuel level indicator light

24p002a

Blink

If the fuel level approaches “E” or the low fuel level indicator light blinks, fill the fuel tank as soon as possible.

Fuel gauge

24p001a

the ambient

Depending on temperature, the fuel quantity is less than 45 L (11.9
gal., 9.9 lmp. gal.) even at “F”. However, this does not affect the fuel consumption and the remaining fuel ratio indicated on the gauge. (For details, see “Fuel” on page 146 in Section 3.)

the

The gauge works when ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. Nearly full–Indicator at “F” Nearly empty–Indicator at “E” It is a good idea to keep the tank over 1/4 full. When you refuel on the slope, the indica- tor may not show the correct level. When you refuel less than about 11.4 L (3.0 gal., 2.5 lmp. gal.), the fuel indicator may not change. After the auxiliary battery is reconnected, one segment will flash for a while.

88

Coolant temperature indicator and warning lights

Low coolant temperature indicator light in blue

24p013

24p010a

24p003b

light

At the first blinking of the light, the master warning instrument cluster comes on and the message appears on the multi–information display to remind the driver to fill fuel.

the

in

The fuel system malfunctions in the fol- lowing cases, so contact your Toyota dealer. (cid:1) All the segments blink. (cid:1) The “E” mark and the segments indi-

cating remaining fuel blink.

High coolant temperature warning light in red

The indicator and warning lights indi- cate the coolant temperature when the ignition switch is on. The hybrid sys- tem operating temperature will vary with changes in weather and hybrid system load. The red high coolant temperature warning light will come on when the ignition key is turned to the “ON” position. After a few seconds, the light will go off. If your coolant temperature is cool with the ignition switch on, the blue low cool- ant temperature indicator light comes on. If it keeps lighting on with the hybrid sys- tem fully warmed, contact your Toyota dealer as soon as possible to service the vehicle.

89

If the red high coolant temperature warn- ing light comes on, your hybrid system is too hot. If your vehicle overheats, stop your vehicle and allow the hybrid system to cool. Your vehicle may overheat during severe operating conditions, such as: (cid:1) Driving up a long hill on a hot day. (cid:1) Reducing speed or stopping after high

speed driving.

NOTICE

(cid:2) Do not remove the thermostat in the cooling system as this may cause the hybrid system to over- heat. The thermostat is designed to control the flow of coolant to keep the temperature of the hybrid sys- tem within the specified operating range.

(cid:2) Do not continue driving with an overheated hybrid system. See “If your vehicle overheats” on page 172 in Section 5.

90

Odometer and two trip meters

24p004d

to

To change the meter display, quickly push and release the button. The meter display changes in the order from the odometer to trip meter A to trip meter B, the odometer each then back time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the button until the meter is set to zero. The same process can be applied for resetting the trip meter B.

This meter displays the odometer and two trip meters. 1. Odometer—Shows

total distance

the

the vehicle has been driven.

2. Two

trip meters—Show

two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.

fuel economy and

the other

3. Trip meter

reset button—Resets

the to zero, and also

trip meters

two change the meter display.

Switching km/h MPH button

Service reminder indicators and warning buzzers— —Instrument cluster

If the indicator or buzzer comes on ...

Do this.

If the indicator or buzzer comes on ...

Do this.

24p005b

(a)

or

If parking brake is off, stop immediately and contact Toyota dealer.

You can switch the display between km/h and MPH by pressing the button.

(Indicator and buzzer)

(b)

(Indicator and buzzer)

(c)

(d)

(e)

Fasten driver’s seat belts.

Fasten front passenger’s seat belt.

Take vehicle to Toyota dealer.

Take vehicle to Toyota dealer.

(f)

(g)

(h)

(i)

(j)

or

See multi–information display.

Drive without hard acceleration.

Stop and check.

Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer.

Take vehicle to Toyota dealer immediately.

91

If the indicator or buzzer comes on ...

Do this.

(k)

(l)

(m)

Close all doors.

Fill up tank.

Stop and check.

(in red)

(n) Key reminder Remove key.

buzzer

(o) Shift position

reminder buzzer

Put the selector lever . in “P” position.

92

(a) Brake System Warning Light and

Buzzer

This light comes on in the following cases when the ignition key is in the “ON” posi- tion. (cid:1) When the parking brake is applied... This light comes on for a few seconds when to the “ON” position even after the parking brake is released. (cid:1) When the brake fluid level is low...

ignition key

turned

the

is

CAUTION

It is dangerous to continue driving normally when the brake fluid level is low.

(cid:1) When the regenerative brake system

is fails...

(cid:1) When fails...

the hydraulic brake booster

If the hydraulic booster causes a problem resulting in poor braking performance, the warning light comes on and buzzer sounds continuously.

Have your vehicle checked at your Toyota dealer in the following cases: (cid:1) The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.

(cid:1) The light does not come on even if the ignition key is turned on with the park- ing brake released.

A warning light turning on briefly during operation does not indicate a problem.

CAUTION

If any of the following conditions oc- curs, immediately stop your vehicle at a safe place and contact your Toyota dealer. (cid:1) The

light does not turn off even after the parking brake is released while the hybrid system is running. (cid:1) The warning buzzer comes on to-

gether with the warning light.

In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.

(cid:1) The brake system warning light re- mains on together with the “ABS” warning light.

In this case, not only the anti–lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.

Any of the following conditions may oc- cur, but do not indicate the malfunc- tion: (cid:1) The light may stay on for about 60
seconds after the ignition key is turned to the “ON” position. It is normal if it turns off after a while.

turn on

(cid:1) Depressing the brake pedal repeatedly may light and buzzer. It is normal if the light turns off and the buzzer stops sounding after a few seconds.

the warning

(cid:1) You may hear a small sound in the engine compartment after the hybrid system is started or the brake pedal is depressed repeatedly. This is a pump pulsating sound of the brake system, and it is not a malfunction.

(b) Driver’s Seat Belt Reminder Light

and Buzzer

to

remind you

light and buzzer

This buckle up the driver’s seat belt. Once the ignition key is turned to ”ON” or ”START”, the reminder light flashes and the buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light keeps on flashing and the buzzer sounds 4 to 8 seconds. (c) Front Passenger’s Seat Belt

Reminder Light

This light reminds you to buckle up the front passenger’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. Unless the front passenger fastens the belt, the light stays flashing. front If passenger seat, depending on its weight and how it is placed on the seat, built–in sensors in the seat cushion may detect the pressure, causing the reminder light to come on.

is placed on

luggage

load

the

(d) Discharge Warning Light This light warns that the auxiliary battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The hybrid system will continue to oper- ate, however, until the auxiliary battery is discharged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.

93

(e) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on or the lamp comes on while driving, first check the following: (cid:1) Empty fuel tank

If the fuel tank is empty, refuel immedi- ately.

This case is a temporary malfunction. The malfunction indicator lamp will go off after taking several driving trips. If the lamp will not go off even after several trips, contact your Toyota deal- er as soon as possible. (cid:1) There is a problem somewhere in the hybrid system or warning light system itself.

Contact your Toyota dealer as soon as possible to service the vehicle.

Emissions inspection and maintenance (I/M) programs Your vehicle may not pass a state emis- sion inspection if the malfunction indicator lamp