2007 Toyota Avalon Owners Manual

temperature, press

temperature on

increase

the

the

237

the

temperature on

With the “DUAL” button indicator off—This button changes the driver side and front passenger side si- multaneously. This function will be cancelled when the “PASSENGER TEMP” button on the instru- ment panel is pushed. “OFF” button Push the “OFF” button to turn off the air conditioning system.

Instrument panel and rear vents

Side vents

Rear vents

If air flow control is not satisfactory, check the instrument panel vents and rear vents. The instrument panel vents and rear vents may be opened or closed as shown.

238

Center vents

Air conditioning filter—

The air conditioning filter information label is placed as shown and indicates that a filter has been installed. The air conditioning filter prevents dust from entering the vehicle through the air conditioning vent.

This air conditioning system has a high efficient air refiner filter which helps eliminate dust and pollen, thereby in- creasing your driving comfort. The air conditioning filter is set behind the glove box.

—Checking and replacing the air conditioning filter The air conditioning filter may clog af- ter long use. The filter may need to be cleaned or replaced if the air flow of the air conditioner and heater experi- ences extreme reductions in operating efficiency, or if the windows begin to fog up easily. To maintain the air conditioning efficiency, cleaning and replace the air conditioning filter according to the maintenance sched- ule. In dusty areas or areas with heavy traffic flow, such as inner city or desert areas, early replacement may be required. (For scheduled maintenance information, please refer the “Scheduled Mainte- nance Guide” or “Owner’s Manual Supple- ment”.)

to

239

REMOVAL METHOD: 1. Open

the glove box. Remove

the screw with a Phillips−head screw- driver and slide off the damper as shown.

2. Push in each side of the glove box

to disconnect the claws.

3. Remove the filter cover while push-

ing in both ends of the cover.

240

4. Pull the filter out of the filter outlet.

CLEANING METHOD: If the filter is dirty, clean by blowing compressed air through the filter from the downward side. Hold the air gun 5 cm (2 in.) from the filter and blow for approximately 2 minutes at 500 kPa (5.0 kgf/cm2 or bar, 72 psi). If is not available, have filter cleaned by your Toyota dealer.

the

it

NOTICE

When cleaning the filter, do not clean the filter with water.

REPLACEMENT METHOD: When inserting the filter in the filter outlet, keep the “↑ UP” mark pointing up.

INFORMATION

The air filter should be installed prop- erly in position. The use of air condi- tioning with the air filter removed may cause deteriorated dustproof per- formance and then affect air condi- tioning performance.

241

242

SECTION 1− 10

OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Center display Clock Compass Cigarette lighter and ashtrays Power outlets Garage door opener Glove box Auxiliary boxes Rear console box Cup holders Rear electric sunshade Storage box Grocery bag hooks Cargo net Floor mat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

244
247
247
252
253
254
257
258
259
260
261
262
262
263
263

243

1. Audio display

(For details, see “Audio system” on page 195 in Section 1−8.)

2. Air conditioning display

(For details, see “Air conditioning system” on page 229 in Section 1−9.)

3. Pattern selector knob 4. Cruise information display 5. Outside temperature display

Center display—

244

the

the center display with

—Before using the center display Operate ignition switch on. When the ignition switch is set at ON, the last previously used mode displayed just before the ignition switch is turned off will appear. If the electrical power source has been disconnected from the center display, the display will automatically be set to the initial mode. When lights are the turned on, the brightness of the display may be reduced.

instrument panel

Pattern selector knob This knob is used to select the pattern of the display. Every time you push the pattern selector knob, the display illuminates in the follow- ing order. 1. All the display 2. Audio display and air conditioning dis-

play

3. Display off

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

245

—Outside temperature display

—Cruise information display

The actual driving range varies with driv- ing habits and road conditions. If fuel con- sumption is good, the driving range will be longer than indicated. If fuel consumption is poor, the driving range will be shorter than indicated. 2. Elapsed time (“TRIP TIME”)

The elapsed time after the engine starts is displayed. When the engine is started, driving time is counted from 0:00. Up to 99:59 (99
hours, 59 minutes) can be displayed. When the driving time exceeds 99:59, the counter returns to 0:00. The calculation is reset when the ignition switch is turned off. 3. Average fuel consumption after re-

fueling (“AVERAGE”)

Average fuel consumption after refuel- ing is calculated and displayed based on total driving distance and total fuel consumption with the engine running. The displayed value is updated every 10
seconds. Every time you refuel the vehicle, the av- erage fuel consumption after refueling cal- culation is automatically reset.

1. Driving range

(“FUEL RANGE”)

fuel

The distance the vehicle can travel with the remaining is calculated and displayed based on the quantity of re- maining fuel and past fuel consumption. The displayed value is updated every 10
seconds. Every the driving range calculation is automatically reset.

time you refuel

the vehicle,

from

temperature

the outside air

The outside temperature value is updated every 1 second. The displayed ranges −30(cid:4)C (−22(cid:4)F) up to 50(cid:4)C (122(cid:4)F). If an abnormality exists in the connection of temperature sensor, “−−”, “F” or “E” will appear on the display. If “−−”, “F” or “E” appears on the display, contact your Toyota dealer. There may be a case that “−−”, “F” or “E” appears momentarily when ignition switch is quickly set to ON. It is normal if it goes out soon.

the

246

Clock

Compass

the

instrument panel

When lights are turned on, the brightness of the time in- dication may be reduced.

the

To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. If quick adjustment to a full hour is de- sired, push the “:00” button. if the “:00” button is de- For example, pressed when is between 1:01—1:29, the time will change to 1:00. If the time will change to 2:00. The ignition switch must be set at ON. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock).

is between 1:30—1:59,

time

time

the

The direction is indicated on the inside rear view mirror. If the ignition switch was turned off with the system on, the system will automati- cally turn back on when the ignition switch is turned on.

Push the “ pass system on and off.

” switch to turn the com-

247

(cid:2) The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

(cid:2) The vehicle is magnetized. (There is a magnet or a metal object on or near the inside rear view mirror.)

the deviation

(cid:2) The battery has been disconnected. If your vehicle is out of the set zone, refer to “CALIBRATING THE COMPASS” below to set the zone number. If the compass works to calibrate the direction automati- cally while the vehicle is in motion. For additional precision or calibrating, see COMPASS” below.

for complete THE

“CALIBRATING

is small,

The compass sensor is in the inside rear view mirror.

NOTICE

Do not put magnets or a metal object on or near the inside rear view mirror of the vehicle. Doing this may cause malfunction of the compass sensor.

indicates

the vehicle

the direction The compass that the above case, it shows that the vehicle is heading north.

is heading.

In

Displays

NE SE SW NW

Directions

North

Northeast

East

Southeast

South

Southwest

West

Northwest

The compass may not show the correct direction in the following conditions: (cid:2) The vehicle is stopped immediately af-

ter turning.

(cid:2) The compass does not adjust while the

vehicle is stopped.

(cid:2) The ignition switch is turned off imme-

diately after turning.

(cid:2) The vehicle is on an inclined surface.

248

the

from

CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on true direction deter- deviates mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust this deviation, stop the vehicle, then push and hold the “ ” switch until the zone number appears on the display. Then push the “ ” switch, referring to the following map to select the number of the zone where the vehicle is.

249

Samoa: 5

Guam:

Saipan: 8

After calibration, leaving the system for several seconds returns it to the compass mode.

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Zone number

250

the direction display on

CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. To rectify this, stop the vehicle and push and hold the “ ” switch until “C” appears on the display. If “C” appears on the display because of a drastic change in the magnetic field, perform circling calibration.

in a circle, drive around

Drive the vehicle in a circle at 8 km/h (5
mph) or less. If there is not enough space to drive the block. After driving 1 to 3 circles in the above method, calibration is completed when the direction is shown on the display. If calibration cannot be performed because of the magnetized vehicle etc., take your vehicle to Toyota dealer.

Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the battery has been removed, re- placed or disconnected. (cid:2) Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

in a place where

(cid:2) During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.

251

Cigarette lighter and ashtrays

CAUTION

(cid:2) When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

(cid:2) Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Type A

Type B

252

CIGARETTE LIGHTER (type A) To use the cigarette lighter, first open the ashtray lid, then press in the light- er. After it finishes heating up, it auto- matically pops out ready for use. If the engine is not running, the ignition switch must be set at ACC. Do not hold the cigarette lighter pressed in. Use a Toyota genuine cigarette lighter or equivalent for replacement. ASHTRAY Type A: To use the ashtray, push the lid to open. Type B: Open the lid of the cup holder and set the ashtray in it. It can be used outside the vehicle. To use the ashtray, raise the lid. When finished with your cigarette, thor- oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, close the lid completely. To detach the ashtray, pull it out.

CAUTION

To reduce the chance of in case of an accident or sudden stop while driving, always completely close the ashtray after use.

injury

Power outlets

Rear console box

The power outlets are designed power supply for car accessories. The ignition switch must be set at ACC or ON for the power outlet to be used.

for

NOTICE

(cid:1) To prevent the fuse from being blown, do not use the electricity over the total vehicle capacity of 12
V/120W.

(cid:1) To prevent the battery from being discharged, do not use the power outlet longer than necessary when the engine is not running.

(cid:1) Close the power outlet lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.

Center auxiliary box

253

transmitter prior

(a) Programming the HomeLink(cid:3) The HomeLink(cid:3) in your vehicle has 3
buttons and you can store one program for each button. To ensure correct programming into the HomeLink(cid:3), install a new battery in the hand−held to program- ming. The battery side of the hand−held trans- mitter must be pointed away the HomeLink(cid:3) during the programming pro- cess. For Canadian users, follow the procedure “Programming an entrance gate/Pro- in gramming all devices the Canadian market”. 1. Decide which of 3 HomeLink(cid:3) buttons

from

in

you want to program.

HomeLink(cid:5)

25 to 75 mm (1 to 3 in.)

Hand−held garage transmitter

2. Place your hand−held garage transmit- ter 25 to 75 mm (1 to 3 in.) away from the surface of the HomeLink(cid:3).

Keep the indicator light on the HomeLink(cid:3) in view while programming.

Garage door opener

Indicator light

Buttons

(cid:3)

The garage door opener ( Universal Transceiver) is manufactured under license from HomeLink(cid:3) and can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, etc.

254

3. Simultaneously press and hold

the hand−held garage transmitter button along with the selected HomeLink(cid:3) but- ton.

Do not release the buttons until step 4
has been completed. 4. When

the HomeLink(cid:3) changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

indicator

the

5. Test the operation of the HomeLink(cid:3) by pressing the newly programmed button. If programming a garage door opener, check to see if the garage door opens and closes.

If the garage door does not operate, iden- tify if your garage transmitter is of the “Rolling Code” type. Press and hold the programmed HomeLink(cid:3) button. The ga- rage door has the rolling code feature if the HomeLink(cid:3)) the flashes rapidly and then remains lit after 2 seconds. If your garage transmitter is the “Rolling Code” type, proceed to the heading “Programming a rolling code sys- tem”.

indicator

light

(on

6. Repeat steps 2 through 5 for each re- maining HomeLink(cid:3) button to program another device.

it

is

to

is necessary

Programming a rolling code system “Rolling Code” If your device equipped, follow steps 1 through 4 under the heading “Programming the HomeLink(cid:3)” before proceeding with the steps listed below. 1. Locate the “training” button on the ceil- ing mounted garage door opener motor. The exact the button may vary by brand of garage door opener. Refer the owner’s guide supplied by the garage door opener manufacturer for the location of this “training” button.

location and color of

to

2. Press the “training” button on the ceil- ing mounted garage door opener motor. Following this step, you have 30 seconds in which to initiate step 3 below. 3. Press and release the vehicle’s pro- grammed HomeLink(cid:3) button twice. The garage door may open. the door does open, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door.

If

255

now

should

recognize

The ceiling mounted garage door opener motor the HomeLink(cid:3) unit and be able activate the garage door up/down. 4. Repeat steps 1 through 3 for each re- maining HomeLink(cid:3) button to program another rolling code system.

Programming an entrance gate/Program- ming all devices in the Canadian market 1. Decide which of the 3 HomeLink(cid:3) but-

2. Place

your

tons you want to program. hand−held

gate/device transmitter 25 to 75 mm (1 to 3 in.) away the HomeLink(cid:3).

surface

from

the

of

Keep the indicator light on the HomeLink(cid:3) in view while programming. 3. Press

selected

hold

and

the

HomeLink(cid:3) button.

4. Continuously press and release (cycle) transmitter the hand−held gate/device button every 2 seconds until step 5 is complete.

5. When

the

indicator

the HomeLink(cid:3) changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

256

6. Test the operation of the HomeLink(cid:3) by pressing the newly programmed button. Check to see if the gate/device oper- ates correctly.

7. Repeat steps 1 through 6 for each re- maining HomeLink(cid:3) button to program another device.

Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button Individual HomeLink(cid:3) buttons cannot be erased, however, to reprogram a single button, follow the procedure “Programming the HomeLink(cid:3)”. (b) Operating the HomeLink(cid:3) To operate the appropriate HomeLink(cid:3) button to activate the programmed device. The HomeLink(cid:3) indicator light should come on. The HomeLink(cid:3) continues to send the signal for up the button is pressed.

the HomeLink(cid:3), press

to 20 seconds as

long as

(c) Erasing

the

entire HomeLink(cid:3)

memory (all three programs)

To erase all previously programmed codes at one time, press and hold down the 2
outside buttons for 20 seconds until the indicator light flashes. If you sell your vehicle, be sure to erase the HomeLink(cid:3) the programs stored memory. For additional programming assistance with Universal Transceiver call the: (cid:2) Toyota Customer Experience Center at

HomeLink(cid:3)

your

in

1−800−331−4331 (U.S.A.)

(cid:2) Toyota Canada Customer

Interaction

Centre at 1−888−869−6828 (Canada)

that may be received,

This device complies with Part 15 of the FCC Rules and with RSS−210 of the IC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence including interference that may cause undersired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party re- sponsible for compliance could void the user’s authority to operate the device.

Refer to HomeLink(cid:3) on the internet at: WWW.HOMELINK.COM

CAUTION

(cid:2) When programming the HomeLink(cid:3) Universal Transceiver, you may be operating a garage door or other device. Make sure people and ob- jects are out of the way of the ga- rage door or other device to pre- vent potential harm or damage.

(cid:2) Do not use this HomeLink(cid:3) Univer- sal Transceiver with any garage door opener that lacks the safety stop and reverse feature as re- quired by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door open- er which cannot detect an object (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death.

Glove box

To use the glove box: Open by pulling the lever. Lock by inserting the master key (vehicles with key cylinder−type ignition switch) or mechanical key (vehicles with smart key system) and turning it clockwise. Unlock by inserting the master key (ve- hicles with key ignition switch) or mechanical key (vehicles with smart key system) and turning it counter- clockwise. With the instrument panel lights on, the glove box light will come on when the glove box is open.

cylinder−type

257

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

258

Auxiliary boxes To use the auxiliary boxes, open the lids as shown in the following illustra- tions.

CAUTION

(cid:2) To reduce the chance of injury in case of an accident or sudden stop, always keep the auxiliary box closed while driving.

(cid:2) Type A—It is designed for holding a light objects, do not place any heavy objects in it. Heavy objects may cause the holder to open and contents to fly out resulting in inju- ries.

NOTICE

Type A—During hot weather, the inte- rior of the vehicle becomes very hot. Do not leave anything flammable or deformable such as a lighter, glasses, etc. inside.

Type A (ceiling)

Type B (front console)

Type C (door panel)

Type E (rear seat)

Type D (center console)

Rear console box

To access the rear console box, pull up the lock release lever while raising the rear console box lid.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.

injury

259

Cup holders

It is possible to use the rear console box lid as an armrest by moving it as shown in the illustration. When using the console box, return the lid to its original position.

Type A (center console)

260

Type B (rear armrest)

Type C (rear armrest)

The cup holders are designed for hold- ing cups or drink−cans securely. To use the cup holder, do the following. Type A—Push on the lid. Type B—Pull down the rear armrest. Type C—Pull down the rear armrest and open the lid on the armrest.

CAUTION

(cid:2) Do not place anything else other than cups or drink−cans on the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

(cid:2) To reduce the chance of injury in case of an accident or sudden stop while driving, keep the cup holder closed when it is not in use.

Rear electric sunshade

CAUTION

(cid:2) Do not touch the brackets fastening the sunshade to avoid injuring your fingers or hands.

(cid:2) Do not put your fingers in the sun- shade groove while the sunshade is operating them caught or injured by the runner.

to avoid getting

the switch. To

the rear electric sunshade, the sun-

To raise push lower shade, push the switch again. The sunshade works when switch is set at ON. When the selector lever is shifted into the “R” position while the sunshade is raised, the sunshade will be automati- cally lowered. To raise the sunshade, move lever out of “R” position and push the switch.

the selector

ignition

the

261

Storage box

Grocery bag hooks

This box is designed to hold things like bottles.

This hook is designed to hang things like grocery bags.

NOTICE

To prevent damage to the hook, avoid hanging heavy loads on it.

NOTICE

(cid:1) To prevent the vehicle battery from being discharged, always operate the sunshade while the engine is running.

(cid:1) Observe the following to avoid dam-

age and/or malfunction: Do not overload the sunshade mo- tor and other parts (for instance by pushing down on the sunshade bracket while it is opening). Do not place anything where they may hinder the opening/closing of the sunshade. Do not affix anything to the sun- shade. Clean the sunshade groove if there is any foreign matter or dust on it. Do not operate the rear electric sunshade repeatedly for a long time as its motor may overheat.

262

Cargo net

Floor mat

To secure belongings, hang the cargo net on the hooks.

NOTICE

(cid:1) Do not use the net to secure sharp or heavy objects. The net will tear off.

(cid:1) Be sure not to twist the net when

hooking.

Use a floor mat of the correct size. If the vehicle carpet and floor mat have 2 holes, then they are designed for use with 2 locking clips. Attach the floor mat to the vehicle carpet using the clips. Lock the clips the vehicle carpet.

the holes

into

in

CAUTION

Make sure the floor mat is properly placed on the vehicle carpet. If the floor mat slips and interferes with the movement of the pedals during driv- ing, it may cause an accident.

263

264

SECTION 2

INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your toyota Break−in period Fuel Fuel pump shut off system Operation in foreign countries Three−way catalytic converters Engine exhaust cautions Facts about engine oil consumption Iridium−tipped spark plugs Brake system Brake pad wear limit indicators Your Toyota’s identification Theft prevention labels Suspension and chassis Tire information Vehicle load limits Cargo and luggage Types of tires

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

266
266
268
268
269
270
270
272
272
276
277
278
278
279
289
290
292

265

Break−in period Drive gently and avoid high speeds. Your vehicle does not need an elaborate break−in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy and long life of your vehicle: (cid:1) Avoid full

throttle acceleration when

starting and driving.

(cid:1) Avoid racing the engine. (cid:1) Try to avoid hard stops during the first

300 km (200 miles).

(cid:1) Do not drive for a long time at any

single speed, either fast or slow.

Fuel FUEL TYPE Your new vehicle must use only un- leaded gasoline. To help prevent gas station mix−ups, your Toyota has a smaller fuel tank opening. The special nozzle on pumps with un- leaded fuel will fit it, but the larger stan- dard nozzle on pumps with leaded gas will not. the gasoline you use At a minimum, should meet specifications of ASTM D4814 in the U.S.A. and CGSB 3.5−M93
in Canada.

NOTICE

Do not use leaded gasoline. Use of leaded gasoline will cause the three− way catalytic converter to lose its ef- fectiveness and the emission control system to function improperly. Also, this can increase maintenance costs.

266

OCTANE RATING Select Octane Rating 87 (Research Oc- tane Number 91) or higher. Use of unleaded gasoline with an octane rating or research octane number lower than stated above will cause persistent heavy knocking. If it is severe, this will lead to engine damage. If your engine knocks... If you detect heavy knocking even when using if you hear steady knocking while holding a steady speed on level roads, consult your Toyota dealer. However, occasionally, you may notice light knocking for a short time while accel- erating or driving up hills. This is normal and there is no need for concern.

the recommended

fuel, or

in

GASOLINE CONTAINING DETERGENT ADDITIVES Toyota recommends the use of gasoline that contains detergent additives to avoid build−up of engine deposits. However, all gasoline sold the U.S. contains detergent additives to keep clean and/or clean intake systems. QUALITY GASOLINE Automotive manufacturers in the U.S., Europe and Japan have developed a specification fuel named World−Wide Fuel Charter (WWFC) that is expected to be applied world wide. The WWFC consists of four categories that depend on required emission lev- els. In the U.S., category 4 has been adopted. The WWFC improves air quali- ty by providing for better emissions in vehicle fleets, and customer satisfaction through better vehicle performance.

for quality

CLEANER BURNING GASOLINE Cleaner burning gasoline, including re- formulated gasoline that contains oxy- genates such as ethanol or MTBE is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gas- oline provide excellent vehicle perfor- mance, reduce vehicle emissions, and im- prove air quality. OXYGENATES IN GASOLINE Toyota allows the use of oxygenate blended gasoline where the oxygenate content is up to 10% ethanol or 15% MTBE. in your Toyota, be sure that it has an octane rating no lower than 87. Toyota does not recommend the use of gasoline containing methanol.

If you use gasohol

GASOLINE CONTAINING MMT Some gasoline contain an octane en- hancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel con- taining MMT is used, your emission con- trol system may be adversely affected. The Malfunction Indicator Lamp on the in- strument cluster may come on. If this hap- pens, contact your Toyota dealer for ser- vice. GASOLINE QUALITY In a very few cases, you may experience driveability problems caused by the partic- ular gasoline that you are using. If you continue to have unacceptable driveability, try changing gasoline brands. If this does not rectify your problem, then consult your Toyota dealer.

267

NOTICE

(cid:1) Do not use gasohol other than stated above. It will cause fuel sys- tem damage or vehicle performance problems.

(cid:1) If driveability problems are encoun- tered (poor hot starting, vaporizing, engine knock, etc.), discontinue the use.

(cid:1) Take care not to spill gasohol dur- ing refueling. Gasohol may cause paint damage.

FUEL TANK CAPACITY

70 L (18.5 gal., 15.4 Imp. gal.)

Fuel pump shut off system The fuel pump shut off system stops sup- plying fuel to the engine to minimize the risk of fuel leakage when the engine stalls or an airbag inflates upon collision. To restart the engine after the fuel pump shut off system activates, set ignition switch to ACC or off once and start it.

the

Operation in foreign countries If you plan to drive your Toyota another country... First, comply with the vehicle registration laws. Second, confirm the availability of the cor- rect fuel (unleaded and minimum octane number).

in

CAUTION

Inspect the ground under the vehicle before restarting the engine. If you leaked onto the find that fuel has ground, fuel system has been damaged and is in need of repair. In this case, do not restart the engine.

the

268

Three−way catalytic converters

The three−way catalytic converters are emission control devices in the exhaust system. The purpose is to reduce pollutants in the exhaust gas.

installed

CAUTION

(cid:1) Keep people and combustible mate- rials away from the exhaust pipe while the engine is running. The exhaust gas is very hot.

(cid:1) Do not drive, idle or park your ve- hicle over anything that might burn easily such as grass, leaves, paper or rags.

NOTICE

A large amount of unburned gases flowing into the three−way catalytic converter may cause it to overheat and create a fire hazard. To prevent this and other damage, observe the following precautions: (cid:1) Use only unleaded gasoline. (cid:1) Do not drive with an extremely low fuel level; running out of fuel could cause the engine to misfire, creat- ing an excessive load on the three− way catalytic converter.

(cid:1) Do not allow the engine to run at idle speed for more than 20 min- utes.

(cid:1) Avoid racing the engine. (cid:1) Do not push−start or pull−start your

vehicle.

(cid:1) Do not turn off the ignition while

the vehicle is moving.

(cid:1) Keep your engine in good running order. Malfunctions in the engine electrical system, electronic ignition system/distributor ignition system or fuel system could cause an ex- tremely high three−way catalytic converter temperature.

(cid:1) If the engine becomes difficult to start or stalls frequently, take your vehicle in for a check−up as soon as possible. Remember, your Toyota dealer knows your vehicle and its three−way catalytic converter sys- tem best.

(cid:1) To ensure that the three−way cata- lytic converter and the entire emis- sion control system operate proper- ly, your vehicle must receive the periodic inspections required by the Toyota Maintenance Schedule. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.

269

(cid:1) Keep

the

trunk

lid closed while driving. An open or unsealed trunk lid may cause exhaust gases to be drawn into the vehicle.

(cid:1) To allow proper operation of your vehicle’s ventilation system, keep the inlet grilles in front of the wind- shield clear of snow, leaves, or oth- er obstructions.

(cid:1) If you smell exhaust fumes in the vehicle, open the windows and close the trunk lid to ensure plenty of fresh air enters the vehicle. If you can smell exhaust fumes even though there are no other vehicles in the surrounding area, have your vehicle checked by your Toyota dealer. Continued inhalation of ex- haust fumes can lead to death by gas poisoning.

Facts about engine oil consumption FUNCTIONS OF ENGINE OIL Engine oil has the primary functions of lubricating and cooling the inside of the engine, and plays a major role in main- taining the engine in proper working order. ENGINE OIL CONSUMPTION It is normal that an engine should con- sume some engine oil during normal engine operation. The causes of oil consumption in a normal engine are as follows. (cid:1) Oil is used to lubricate pistons, piston rings and cylinders. A thin film of oil is left on the cylinder wall when a pis- ton moves downwards in the cylinder. High negative pressure generated when the vehicle is decelerating sucks some of this oil into the combustion chamber. This oil as well as some part of the oil film left on the cylinder wall is burned by temperature combustion gases during the combustion process.

the high

Engine exhaust cautions

CAUTION

(cid:1) Avoid inhaling the engine exhaust. It contains carbon monoxide, which is a colorless and odorless gas. It can cause unconsciousness or even death.

(cid:1) Make sure the exhaust system has no holes or loose connections. The system should be checked from time to time. If you hit something, or notice a change in the sound of the the system exhaust, have checked immediately.

(cid:1) Do not run the engine in a garage or enclosed area except the time needed to drive the vehicle in or out. The exhaust gases cannot escape, making this a particularly dangerous situation.

for

(cid:1) Do not remain for a long time in a parked vehicle with the engine run- ning. If it is unavoidable, however, do so only in an unconfined area and adjust the heating or cooling system to force outside air into the vehicle.

270

(cid:1) Oil is also used to lubricate the stems of the intake valves. Some of this oil is sucked into the combustion chamber together with is burned along with the fuel. High tem- perature exhaust gases also burn the oil used to lubricate the exhaust valve stems.

intake air and

the

The amount of engine oil consumed de- pends on the viscosity of the oil, the quality of the oil and the conditions the vehicle is driven under. More oil is consumed by high−speed driv- ing and frequent acceleration and decel- eration. A new engine consumes more oil, since its pistons, piston rings and cylinder walls have not become conditioned. Oil consumption: Max. 1.0 L per 1000
km (1.1 qt./600 miles, 0.9 Imp. qt./600
miles) When judging the amount of oil con- sumption, note the that oil may become diluted and make it difficult to judge the true level accurately.

For detailed information on oil level check, see “Checking level” on page 356 in Section 7−2.

the engine oil

As an example, if a vehicle is used for repeated short trips, and consumes a nor- mal amount of oil, the dipstick may not show any drop in the oil level at all, even after 1000 km (600 miles) or more. This is because the oil is gradually becoming diluted with fuel or moisture, making it appear that the oil level has not changed. The diluting ingredients evaporate out when the vehicle is then driven at high speeds, as on an expressway, making it appear that oil is excessively consumed after driving at high speeds. IMPORTANCE OF ENGINE OIL LEVEL CHECK One of the most important points in prop- er vehicle maintenance is to keep the en- gine oil at the optimum level so that oil function will not be impaired. Therefore, it is essential that the oil level be checked regularly. Toyota recommends that the oil level be checked every time you refuel the vehicle.

NOTICE

Failure to check the oil level regularly could lead to serious engine trouble due to insufficient oil.

271

Brake system The tandem master cylinder brake system is a hydraulic system with two separate sub−systems. If either sub−system should fail, the other will still work. However, the pedal will be harder to press, and your stopping distance will increase. Also, the brake system warning light may come on.

CAUTION

Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.

CAUTION

(cid:1) Do not pump the brake pedal if the engine stalls. Each push on the pedal uses up your reserved vacu- um.

lost,

(cid:1) Even if the power assist

is com- pletely the brakes will still work. But you will have to push the pedal hard, much harder than nor- mal. And your braking distance will increase.

the brakes.

BRAKE BOOSTER The brake booster uses engine vacuum to power−assist the engine should quit while you are driving, you can bring the vehicle to a stop with normal pedal pressure. There is enough reserved vacuum two stops—but no more!

for one or

If

Iridium−tipped spark plugs

Your engine is fitted with iridium−tipped spark plugs.

NOTICE

Use only Toyota genuine iridium− tipped spark plugs and do not adjust gaps for your engine performance and smooth driveability.

For details about the spark plug type, see “Service specifications” on page 383 in Section 8.

272

is

in

You may hear a click or motor sound in the engine compartment for a few seconds when the engine is started or just after the vehicle is started. This means that the anti−lock brake system the self check mode, and does not indicate a mal- function. When the anti−lock brake system is ac- tivated, the following conditions may occur. They do not indicate a malfunc- tion of the system: (cid:1) You may hear the anti−lock brake sys- tem operating and feel the brake pedal pulsating and the vibrations of the ve- hicle body and steering wheel. You may also hear the motor sound in the engine compartment even after the ve- hicle is stopped.

(cid:1) At the end of the anti−lock brake sys- the brake pedal may

tem activation, move a little forward.

ANTI−LOCK BRAKE SYSTEM The anti−lock brake system is designed to automatically help prevent lock−up of the wheels during a sudden braking or braking on slippery road surfaces. This assists in providing directional stability and steering performance of the vehicle under these circumstances.

this situation,

Effective way to press the ABS brake pedal: When the anti−lock brake system function is in action, you may feel the brake pedal pulsating and hear a noise. In the anti−lock brake system work for you, just hold the brake pedal down more firmly. Do not pump the brake in a panic stop. This will result in reduced braking performan- ce.

let

to

The anti−lock brake system becomes op- erative after the vehicle has accelerated to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the vehicle decelerates to a speed below approximately 5 km/h (3 mph). Depressing the brake pedal on slippery road surfaces such as on a manhole cov- er, a steel plate at a construction site, joints in a bridge, etc. on a rainy day tends to activate the anti−lock brake sys- tem.

CAUTION

Do not overestimate the anti−lock brake system: Although the anti−lock brake system assists in providing ve- hicle control, it is still important to drive with all due care and maintain a moderate speed and safe distance from the vehicle in front of you, be- cause there are limits to the vehicle stability and effectiveness of steering wheel operation even with the anti− lock brake system on. If tire grip performance exceeds its capability, or if hydroplaning occurs during high speed driving in the rain, the anti−lock brake system does not provide vehicle control.

273

the vehicle

Anti−lock brake system is not de- signed to shorten the stopping dis- tance: Always drive at a moderate speed and maintain a safe distance from front of you. Compared with vehicles without an anti−lock brake system, your vehicle may require a longer stopping dis- tance in the following cases: (cid:1) Driving on rough, gravel or snow−

in

covered roads.

(cid:1) Driving with tire chains installed. (cid:1) Driving over the steps such as the

joints on the road.

(cid:1) Driving on roads where the road surface is pitted or has other differ- ences in surface height.

Install all 4 tires of specified size at appropriate pressure: The anti−lock brake system detects vehicle speeds using the speed sensors for respec- tive wheels’ turning speeds. The use of tires other than specified may fail to detect the accurate turning speed resulting longer stopping dis- tance.

in a

Type A

Type B

274

if

the

the vehicle stability

light comes on when

few seconds. Thereafter,

“ABS” warning light Vehicles without control system— The ignition switch is set at ON. If the anti−lock brake system works properly, the light turns off after a the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate, but the brake system still operates con- ventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.

in

the following conditions If either of indicates a malfunction occurs, this somewhere the components moni- tored by the warning light system. Con- tact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light does not come on when the ignition switch is set at ON, or remains on.

(cid:1) The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem.

CAUTION

If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.

the

the

light comes on when

Vehicles with the vehicle stability con- trol system— ignition The switch is set at ON. If the anti−lock brake system and the brake assist system work properly, the light turns off after a few seconds. Thereafter, if either of the sys- tems malfunctions, light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system and the brake as- sist system do not operate, but the brake system still operates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.

If either of the following conditions oc- curs, this indicates a malfunction some- where in the components monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light does not come on when the ignition switch is set at ON, or remains on.

(cid:1) The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem.

CAUTION

If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.

275

in

the brakes on,

BRAKE ASSIST SYSTEM (vehicles with vehicle stability control system) the When you slam brake assist system judges as an emer- gency stop and provides more powerful braking for a driver who cannot hold down the brake pedal firmly. When you slam the brakes on, more pow- erful braking will be applied. At this time, you may hear a sound the engine compartment and feel the vibration of the brake pedal. This does not indicate a mal- function. The brake assist system becomes opera- tive after the vehicle has accelerated to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the vehicle decelerates to a speed below approximately 5 km/h (3 mph). For an explanation of this system’s warn- ing light, see “Service reminder indicators and warning buzzers” on page 145 in Sec- tion 1−6.

Brake pad wear limit indicators

The brake pad wear limit indicators on your disc brakes give a warning noise when the brake pads are worn to where replacement is required. If you hear a squealing or scraping noise while driving, have the brake pads checked and replaced by your Toyota dealer as soon as possible. Expensive ro- tor damage can result if the pads are not replaced when necessary.

DRUM−IN−DISC TYPE PARKING BRAKE SYSTEM type Your vehicle has a drum−in−disc parking brake system. This type of brake system needs bedding−down of the brake shoes periodically or whenever the parking brake shoes and/or drums are replaced. Have your Toyota dealer perform the bed- ding−down.

276

Your Toyota’s identification— —Vehicle identification number

—Engine number

The vehicle identification number (VIN) is also on the Certification Label.

The engine number is stamped on the engine block as shown.

The vehicle identification number (VIN) is the legal identifier for your vehicle. This number is on the left top of the instrument panel, and can be seen through the windshield from outside. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.

277

Suspension and chassis

CAUTION

Do not modify the suspension/chassis with lift kits, spacers, springs, etc. It can cause dangerous handling charac- teristics, resulting in loss of control.

Theft prevention labels (except for Canada) Your new vehicle carries theft preven- tion labels which are approximately 47
mm (1.85 in.) by 12 mm (0.47 in.). The purpose of these labels is to reduce the incidence of vehicle thefts by facilitat- ing the tracing and recovery of parts from stolen vehicles. The label is designed so that once it is applied to a surface, any attempt to remove it will result in destroy- ing the integrity of the label. Transferring these labels intact from one part to anoth- er, will be impossible.

NOTICE

You should not attempt to remove the theft prevention labels as it may vio- late certain state or federal laws.

278

Tire information— —Tire symbols (standard tire)

This illustration indicates typical tire symbols. 1. Tire size—For details, see “—Tire

size” on page 283.

2. DOT and Tire

Identification Number (TIN)—For details, see “—DOT and Tire Identification Number (TIN)” on page 282.

3. Location of the tread wear indi- cators—For details, see “Check- ing and replacing tires” on page 363.

4. Uniform tire quality grading— For details, see “—Uniform tire quality grading” on page 284.

5. Tire ply composition and mate- rials—Plies mean a layer of rub- ber−coated parallel cords. Cords mean the strands forming the plies in the tire.

6. Radial tires or bias−ply tires—A radial tire has “RADIAL” on the sidewall. A tire not marked with “RADIAL” is a bias−ply tire.

279

7. “TUBELESS”

or

“TUBE TYPE”—A tubeless tire does not have a tube inside the tire and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure.

8. Load limit at maximum cold tire inflation pressure—For details, see “Vehicle load limits” on page 289 and “Tires” on page 386.

9. Maximum cold

tire

tire

cold

inflation pressure—This means the pres- sure to which a tire may be in- flated. For details about recom- mended inflation pressure, see “Tires” on page 386. tire or all season tire—An all season tire has “M+S” on tire not marked with “M+S” is a summer tire. For details, see “Types of tires” on page 292.

the sidewall. The

10.Summer

280

—Tire symbols (compact spare tire)

This illustration indicates typical tire symbols. 1. “TEMPORARY USE ONLY”—A compact spare tire is identified by the phrase “TEMPORARY USE ONLY” molded into its sidewall. This tire is designed for temporary emergency use only. For details, see “Compact spare tire” on page 321.

2. Tire size—For details, see “—Tire

size” on page 283.

3. DOT and Tire

Identification Number (TIN)—For details, see “—DOT and Tire Identification Number (TIN)” on page 282.

4. Location of the tread wear indi- cators—For details, see “Check- ing and replacing tires” on page 363.

5. Load limit at maximum cold tire inflation pressure—For details, see “Vehicle load limits” on page 289 and “Tires” on page 386.

281

—DOT and Tire Identification Number (TIN)

The “DOT” symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.

This illustration indicates typical DOT and Tire Identification Number (TIN). 1. “DOT” symbol 2. Tire Identification Number (TIN) 3. Tire manufacturer’s identification

mark

4. Tire size code 5. Manufacturer’s optional tire type

code (3 or 4 letters) 6. Manufacturing week 7. Manufacturing year

tire

cold

6. Maximum cold

inflation pressure—This means the pres- sure to which a tire may be in- flated. For details about recom- mended inflation pressure, see “Tires” on page 386. 7. Tire ply composition and mate- rials—Plies mean a layer of rub- ber−coated parallel cords. Cords mean the strands forming the plies in the tire.

tire

8. “TUBELESS”

or

“TUBE