2007 Toyota Avalon Owners Manual

Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Replacing the wiper blades Adding washer fluid Checking the headlight aim Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

372
373
374
375
375
376
377

371

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. (cid:1) Do not cause a spark from the bat-

tery with tools.

(cid:1) Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. (cid:1) Avoid contact with eyes, skin or

clothes.

(cid:1) Never ingest electrolyte. (cid:1) Wear protective safety glasses when

working near the battery.

(cid:1) Keep children away from the bat-

tery.

(cid:1) If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

(cid:1) If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

(cid:1) If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

EMERGENCY MEASURES (cid:1) If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

372

—Checking battery exterior

Terminals

Hold−down clamp

Ground cable

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

—Checking battery condition

NOTICE

Type A

(cid:1) Be sure the engine and all accesso- ries are off before performing main- tenance.

(cid:1) When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.

(cid:1) Be careful not to cause a short cir-

cuit with tools.

(cid:1) Take care no solution gets into the

battery when washing it.

If the battery is disconnected or run down, the power window and moon roof may not operate automatically and the jam protection function will not function cor- rectly after you reconnect, replace or re- charge the battery. In any of these cases, you should normalize each system. To normalize them, see “Power windows” on page 41 and “Electric moon roof” on page 52 in Section 1−2.

Green

Dark

Clear or light yellow

Type B

Blue

White

Red

CHECKING BY INDICATOR Check the battery condition by the indi- cator color.

Indicator color

Type A

Type B

Condition Condition

Green

Blue

Good

Dark

White

Clear or

light yellow

Red

Charging neces- sary. Have battery checked by your Toyota dealer.

Have battery checked by your Toyota dealer.

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

(cid:1) Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

(cid:1) Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

NOTICE

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

373

Checking and replacing fuses

Good

Blown

Good

Blown

Type A

Type B

374

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” on page 349 in Sec- tion 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull the suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See page 387 in Section 8 for the functions controlled by each circuit.

Type B fuses—When any of the fuses are blown, contact your Toyota dealer. Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “MIR HTR”, “CIG” or “A/C” fuse, which may be dispensable for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close to the rating as possible. If the amperage is fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

that specified,

lower

than

the

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible. You should normalize the power window and moon roof if they do not operate au- tomatically or the jam protection function does not operate correctly after replacing blown fuses. To normalize the power win- dow and moon roof, see “Power windows” on page 41 and “Electric moon roof” on page 52 in Section 1−2.

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

Adding washer fluid If any washer does not work, the low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. You may use plain water as washer fluid. However, in cold areas where tempera- tures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

Replacing the wiper blades

When the wipers no longer clean ade- quately, the wiper blades may be worn or cracked, requiring replacement. To remove the wiper blade from the arm, pull the blade in the direction of the arrow while squeezing the clip.

NOTICE

Be careful not to scratch the glass surface with the wiper frame.

375

Checking the headlight aim (with discharge headlight)—

Removing clip

Remove the cover clips with a Phillips− head screwdriver and remove the cov- ers. the cover clip and Remove and cover as shown in the following illustra- tions.

install

376

Installing clip

1: Vertical movement adjusting bolt 1
2: Vertical movement adjusting bolt 2

Before checking the headlight aim: 1. Be sure that the body around the head-

light is not deformed.

2. Park the vehicle on a level spot. 3. The driver gets into the driver’s seat and puts the vehicle in a state ready- ing for a driving (with a full tank). 4. Bounce the vehicle several times.

—Adjusting the vertical aiming

1. Turn

the vertical movement adjusting bolt 1 in either direction using a Phil- lips−head screwdriver. At time, keep the turning direction and number of turns in mind.

this

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table. The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota deal- er to have the light replaced.

2. Turn

the vertical movement adjusting bolt 2 the same number of turns and in the same direction as step 1 using a Phillips−head screwdriver.

CAUTION

(cid:1) To prevent burning yourself, do not replace the light bulbs while they are hot.

(cid:1) Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

377

W Type

Vehicles with discharge headlights— (cid:1) Do not touch the high−intensity dis- charge headlight’s high voltage socket when the headlights are turned on. An extremely high volt- age of 20000 V will be discharged and could result in serious injury or death by electric shock.

(cid:1) Do not attempt to take apart or re- pair the low beam headlight bulbs, connectors, power supply circuits, or related components. Doing so could result in electric shock and serious injury or death. Call your Toyota dealer for headlight repair or servicing, including replacement of bulbs and bulb disposal.

NOTICE

Only use a bulb of the listed type.

378

the

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lens becomes wet in the rain or in a car wash. This is not a problem because the is caused by fogging temperature difference between the outside and the windshield fogs up in the rain. However, if there large drop of water on the inside of the lens, or if there is water pooled light, contact your Toyota dealer.

inside of

inside

lens,

is a

just

like

the

the

Light bulbs

Headlights (low)

Discharge bulbs Halogen bulbs

Headlights (high) Front fog lights

Front turn signal/parking lights Front side marker lights Rear turn signal lights Stop/tail lights

Rear side marker lights Tail lights

Back−up lights

License plate lights Interior light

Bulb No.

D2R

9006

9005

9006

35

51

60

51

3457A

27/7

W5W

469

21

7443

21/5

194

194

921

194

W5W

3.8

3.8

16

3.8

W Type

Light bulbs

Front personal lights Rear personal lights Vanity lights

Glove box light

Door courtesy lights Trunk light

Bulb No.

W5W

W5W

7065

74

168

1.4

1.2

2825

4.8

A: D2R discharge bulbs B: HB4 halogen bulbs C: HB3 halogen bulbs D: Wedge base bulbs (amber) E: Wedge base bulbs (clear) F: Double end bulbs

—Headlights, front fog, front turn signal/parking, front side marker, tail and back−up lights, and LED* type high mounted stoplight If either the left or right headlights, front turn signal/parking, front side marker, tail or back−up light- s, or LED* type high mounted stoplight burns out, contact your Toyota dealer.

front

fog,

NOTICE

Do not try to replace the headlights, front fog, front turn signal/parking, front side marker, tail or back−up light bulbs by yourself. You may dam- age the vehicle.

* : Light−emitting Diode

—Rear turn signal, stop/tail and rear side marker lights

379

—License plate lights

a: Rear turn signal light b: Stop/tail light c: Rear side marker light

Use a flathead screwdriver.

380

SECTION 8

SPECIFICATIONS Specifications Dimensions and weights Engine Fuel Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

382
382
383
383
386
387

381

Dimensions and weights

Overall length

Overall width Overall height*

Wheelbase

Front tread

Rear tread

Vehicle capacity weight (occupants + luggage)

Towing capacity (trailer weight + cargo weight) * : Unladen vehicle

mm (in.)

5010 (197.2)

Engine Model:

3.5 L V6 (2GR−FE)

mm (in.)

1850

(72.8)

Type:

mm (in.)

1485

(58.5)

mm (in.)

2820 (111.0)

mm (in.)

1581

(62.2)

mm (in.)

1570

(61.8)

kg (lb.)

kg (lb.)

395

(870)

454 (1000)

6 cylinder V type 4 cycle, gasoline

Bore and stroke, mm (in.):

94.0 (cid:1) 83.0 (3.70 (cid:1) 3.27)

Displacement, cm3 (cu. in.):

3456 (210.9)

382

Fuel Fuel type:

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher.

Fuel tank capacity, L (gal., Imp. gal.):

70 (18.5, 15.4)

Service specifications ENGINE Spark plug type:

DENSO

FK20HR11

Spark plug gap, mm (in.):

1.1 (0.043)

NOTICE

Use only above spark plugs. Do not adjust gaps for engine performance or smooth driveability.

ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):

With filter Without filter

6.1 (6.4, 5.4) 5.7 (6.0, 5.0) “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

is used

satisfy

the

ILSAC multigrade engine oil.

Recommended oil viscosity:

SAE 5W−30

Outside temperature

Please contact your Toyota dealer for fur- ther details.

383

it

in

listed

Guide”

is necessary

Generally, to change automatic transmission fluid only if your vehicle is driven under one of the Special Operating Conditions your “Scheduled Maintenance or “Owner’s Manual Supplement”. When changing the automatic transmission fluid, use only “Toyota Genuine ATF WS” (ATF JWS3324 or NWS9638) to aid in assuring maximum transaxle performance. Notice: Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimate- ly damage the automatic transmission of your vehicle. Please contact your Toyota dealer for fur- ther details.

COOLING SYSTEM Total capacity, L (qt., Imp. qt.):

BATTERY Open voltage* at 20(cid:1)C (68(cid:1)F):

12.6—12.8 V 12.2—12.4 V 11.8—12.0 V

* : Voltage

Fully charged Half charged Discharged

that

is checked 20 minutes after the key is removed (vehicles with key cylinder−type ignition switch) or the engine (vehicles with smart key system) with all the lights turned off.

turned off

is

Charging rates:

5 A max.

AUTOMATIC TRANSAXLE Fluid capacity (drain and refill), L (qt., Imp. qt.):

Up to 3.5 (3.7, 3.1)

Fluid type:

Toyota Genuine ATF WS

Change automatic transmission fluid only as necessary.

8.3 (8.8, 7.3)

Coolant type:

“Toyota Super Long Life Coolant” is used in your Toyota vehicle at factory fill. In order to avoid technical problems, only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life hybrid organic acid technology. (Coolant with long−life hybrid organic acid technology is a combination of low phosphates and organic acids.) Do not use plain water alone. Please contact your Toyota dealer for further details.

384

BRAKES Minimum pedal clearance when depressed with the force of 490 N (50 kgf, 110 lbf) with the engine running, mm (in.):

77 (3.0)

Pedal free play, mm (in.):

1—6 (0.04—0.24)

Pad wear limit, mm (in.):

1.0 (0.04)

Lining wear limit, mm (in.):

1.0 (0.04)

Parking brake adjustment when depressed with the force of 294 N (30 kgf, 66.1 lbf):

9—11 clicks

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

STEERING Wheel free play:

Less than 30 mm (1.2 in.)

Power steering fluid type:

Automatic transmission fluid DEXRON(cid:2)II or III

385

Tires Tire size and cold tire inflation pressure: Front and rear

kPa (kgf/cm2 or bar, psi)

Tire size Tire size

P215/60R16 94V P215/55R17 93V

Tire inflation pressure

Under 160 km/h (99 mph) Over 160 km/h (99 mph)

200 (2.0, 29) 220 (2.2, 32)

240 (2.4, 35) 260 (2.6, 38)

Wheel size Wheel size

16 (cid:1) 6 1/2JJ

17 (cid:1) 7JJ

When driving under the above vehicle load conditions at sustained high speeds above 160 km/h (100 mph), in countries where such speeds are permitted by−law, inflate the front and rear tires to 280 kPa (2.8 kgf/cm2 or bar, 41 psi) provided that it does not exceed the maximum cold tire pressure molded on the tire sidewall. Spare

kPa (kgf/cm2 or bar, psi)

Tire size

Tire inflation pressure

P215/60R16 94V P215/55R17 93V T155/70R17 110M

200 (2.0, 29) 220 (2.2, 32) 420 (4.2, 60)

Wheel size

16 (cid:1) 6 1/2JJ

17 (cid:1) 7JJ 17 (cid:1) 4T

Wheel nut torque, N·m (kgf·m, ft·lbf):

103 (10.5, 76)

NOTE: For complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire inflation pressure”

through “Aluminum wheel precautions” on pages 361 through 369 in Section 7−2.

386

Fuses

Instrument panel

Fuses (type A) 1. EFI NO.2 10 A: Multiport fuel injection injec-

system/sequential multiport tion system

fuel

2. STOP NO.2 7.5 A: Stop lights, high mounted stoplight, vehicle stability con- trol system, anti−lock brake system

3. RADAR CC 7.5 A: Vehicle stability

control system

4. HEAD RH LWR 15 A: Right−hand

headlight (low beam)

5. HEAD LH LWR 15 A: Left−hand head-

light (low beam)

Engine compartment

6. INJ 15 A: Multiport fuel injection sys- injection

tem/sequential multiport system

fuel

7. STOP NO.1 15 A: Multiplex commu-

nication system

8. STR LOCK 25 A: Steering lock system 9. IMMOBI 7.5 A: Smart key system 10. AMP 30 A: Audio system 11. TURN/HAZ 15 A: Turn signal lights 12. IG2 25 A: Multiport fuel injection sys- injection

tem/sequential multiport system

fuel

13. ETCS 10 A: Multiport

fuel

system/sequential multiport tion system

injection injec-

fuel

14. ALT−S 7.5 A: Charging system 15. DOOR NO.1 25 A: Multiplex commu-

nication system

16. AM2 7.5 A: Starter system 17. RAD NO.1 15 A: Audio system, center

display, navigation system

18. ECU−B 10 A: Center display, multiplex

communication system

387

19. DOME 7.5 A: Gauges and meters, clock, front personal lights, door cour- tesy lights, garage door opener, rear personal lights, trunk light

20. S−HORN 7.5 A: Horn 21. WASHER 20 A: Windshield washer 22. A/F 25 A: Air fuel ratio sensor 23. HEAD RH UPR 15 A: Right−hand

headlight (high beam)

24. HEAD LH UPR 15 A: Left−hand head-

light (high beam)

25. HORN 10 A: Horn 26. EFI NO.1 25 A: Multiport fuel injection injec-

system/sequential multiport tion system, fuel pump

fuel

27. RR DOOR 25 A: Power window (for

rear right passenger)

28. RL DOOR 25 A: Power window (for

rear left passenger)

29. FR DOOR 25 A: Power window (front passenger), driving position memory system

30. FOG 15 A: Front fog lights 31. OBD 7.5 A: On−board diagnosis sys-

tem

32. MPX−B 7.5 A: Multiplex communication

system

388

33. P/W 25 A: Power window, driving posi-

tion memory system

34. FUEL OPN 7.5 A: Fuel

filler door

opener

43. HTR 7.5 A: Air conditioning system, instrument panel lights, electric cooling fan

44. A/C COMP 7.5 A: Air conditioning sys-

35. AM1 7.5 A: Multiport fuel injection sys- fuel injection ignition sys-

tem/sequential multiport system, starting system, tem

36. A/C 7.5 A: Air conditioning system 37. DOOR NO.2 25 A: Multiplex commu-

nication system

38. S/ROOF 30 A: Electric moon roof 39. TAIL 10 A: Parking lights, license plate lights, tail lights, front and rear side marker lights

40. PANEL 7.5 A: Seat heaters, navigation system, emergency flasher, electroni- cally controlled automatic transmission system, glove box light, instrument panel lights, power outlets

41. ECU IG NO.1 10 A: Center display, shift lock control system, electric moon roof, multiplex communication system

42. ECU IG NO.2 10 A: Anti−lock brake laser cruise control system, dynamic system, automatic headlight leveling system, vehicle stability control system, multiplex communication system

tem

45. S−HTR 20 A: Air conditioning system 46. GAUGE NO.1 10 A: Back−up lights, navigation system, emergency flashers

47. WIP 30 A: Windshield wipers 48. RR S/SHADE 10 A: Rear electric sun-

shade

49. IGN 10 A: Multiport fuel injection sys- tem/sequential multiport injection system, SRS airbag system, front pas- senger occupant classification system, smart key system, starter system

fuel

50. GAUGE NO.2 7.5 A: Gauges and me-

ters, center display

51. ECU−ACC 7.5 A: Power rear view mir- rors, center display, shift lock system, multiplex communication system

52. CIG 15 A: Cigarette lighter 53. PWR OUTLET 15 A: Power outlets 54. RADIO NO.2 7.5 A: Audio system,

navigation system

55. MIR HTR 10 A: Outside rear view mir-

ror defoggers

Fuses (type B) 56. ALT 120 A (vehicles without com- pass)/140 A (vehicles with compass): Charging system, “RR DEF”, “ABS/VSC NO.2” “ABS/VSC NO.1”, “RDI FAN”, “WASHER” and “S−HORN” fuses

“HEATER”,

57. MAIN 40 A: Headlights 58. ST/AM2 30 A: Starter system 59. HEATER 50 A: Air conditioning system 60. ABS/VSC NO.1 50 A: Anti−lock brake system, vehicle stability control system

61. RDI FAN 50 A: Electric cooling fan 62. ABS/VSC NO.2 30 A: Anti−lock brake system, vehicle stability control system 63. RR DEF 50 A: Rear windshield defog- ger, outside rear view mirror defoggers

389

390

SECTION 9

REPORTING SAFETY DEFECTS FOR U.S. OWNERS Reporting safety defects for u.s. owners Reporting safety defects for U.S. owners

. . . . . . . . . . . . . . . . . . . . . .

392

391

Safety

Hotline

toll−free

To contact NHTSA, you may call the Ve- hicle at 1−888−327−4236 (TTY: 1−800−424−9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain other information about motor ve- hicle safety from http://www.safercar.gov.

Reporting safety defects for U.S. owners If you believe that your vehicle has a de- fect which could cause a crash or could cause injury or death, you should immedi- ately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll−free: 1−800−331−4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot be- come involved in individual problems be- tween you, your dealer, or Toyota Motor Sales, U.S.A., Inc.

392

This quick reference guide provides you with information on Dynamic Laser Cruise Control Vehicle−to−Vehicle Distance Control Mode. Prior to use of this system, you should be thoroughly familiar with this system, referring to “Dynamic Laser Cruise Control” in Section 1−7, Owner’s Manual in conjunction with this quick reference guide. (cid:3) Dynamic Laser Cruise Control Operation The laser radar sensor in this system primarily detects the reflectors of the vehicle ahead of you to determine the presence of the vehicle and the vehicle−to−vehicle distance. The detection range of the sensor is about 120 m (400 ft.) ahead. (cid:2) If no vehicle is detected ahead of you:

(cid:1) Your cruising speed is maintained at the preset speed from about 40 km/h (25 mph) to about 135 km/h (85 mph).

(cid:2) If a vehicle is detected ahead of you:

(cid:1) Your cruising speed changes in proportion to the speed of the vehicle ahead to maintain an appropriate distance from your vehicle

to the vehicle ahead.

(cid:1) If the vehicle ahead is out of the detection range, your cruising speed will be gradually increased up to the preset speed, and your

vehicle resumes fixed−speed cruising.

(cid:1) If the vehicle ahead decelerates abruptly or other vehicles cut in ahead of you, your vehicle may be too close to the vehicle ahead

of you. If this occurs, the display flashes and beeps. (Approach warning)

The dynamic laser cruise control should be used on roads in which sufficient vehicle−to−vehicle distance will be ensured (such as on freeways).

- 1 -

(cid:3) Operation Requirements

Cruising from about 40 km/h (25 mph) to about 135 km/h (85 mph)

O001qrg

The wipers are not operating at all or operating intermittently (including the same wiper operation in the “AUTO” position).

The selector lever is in the “D” position or the shift range position is in the “4” (forth range) or “5” (fifth range) in “S” mode.

Even if these requirements are met, the system may not operate properly under certain conditions such as bad weather. See Owner’s Manual for Complete Information.

- 2 -

(cid:3) Cautions (cid:2) Do not rely too much on dynamic laser cruise control. Vehicle−to−vehicle distance control has its limitations.

Always remain aware of the distance from the vehicle ahead and other vehicles. If necessary, depress the brake pedal to ensure sufficient distance.

(cid:2) Dynamic laser cruise control is not a collision−avoidance system.

If necessary, depress the brake pedal to ensure sufficient distance.

(cid:2) Dynamic laser cruise control should not be used in the following conditions:

(cid:1) In bad weather (such as rain, fog, snow, sandstorms) (cid:1) In direct sunlight from the front (cid:1) Raindrops or snowflakes get in the laser radar sensor glass (cid:1) On the roads in heavy traffic or at sharp bends (cid:1) On slippery road surfaces (icy or snow−covered road surfaces) (cid:1) On steep downhill slopes (cid:1) Continual acceleration or deceleration (such as on busy traffic) (cid:1) On roads with steep and short inclines and declines In any conditions of the above, an appropriate vehicle−to−vehicle distance control may not be attained.

(cid:2) This system is not provided to justify careless driving.

Always remain aware of the distance from the vehicle ahead and other vehicles.

(cid:2) The dynamic laser cruise control should not be used when exiting from,

or when entering or merging onto a freeway. When you are following a slower moving vehicle and exiting, the sensor does not detect the vehicle and will accelerate to preset speed.

- 3 -

O002qrg

O003qrg

(cid:3) Cautions (cid:2) If other vehicles are driving outside of the laser radar detection range, a delay in the detection of the vehicle cutting in

at short range or detection failure of the motorcycle running on the side of the same lane will occur. In this case, the dynamic laser cruise control system will not function properly.

(cid:2) The distance between your vehicle and the vehicle ahead cannot be accurately detected in the following cases:

(cid:1) The vehicle ahead has higher ground clearance, which means that the placement of the reflectors is in a higher position. (cid:1) The rear section of the vehicle ahead is extremely dirty. (cid:1) The vehicle ahead or other vehicles around you are flinging up water or snow. (cid:1) Excessive exhaust gas (black smoke) is coming from the vehicle ahead or other vehicles around you, obscuring your front

view.

(cid:1) Protective film is attached to the reflectors on the vehicle ahead, or reflectors are not installed on the vehicle ahead or are

damaged.

(cid:1) Heavy luggage is loaded on top of your rear seats.

(cid:2) The laser radar sensor automatically detects dirt if dirt is sticking to the sensor glass of your vehicle.

However, in some cases dirt may not be detected. At this time warning display does not operate and an appropriate vehicle−to−vehicle distance cannot be maintained. Continue driving with due care to the vehicle ahead.

(cid:2) Dynamic laser cruise control does not operate when the vehicle is at a stop or is driving very slowly.

(cid:1) Pay special attention to the very slow vehicle at the end of the line in heavy traffic or at the toll gate.

(cid:2) Turn off the main switch when dynamic laser cruise control is not in use. (cid:2) The approach warning may not turn on even if the vehicle drives closer to the vehicle ahead in the following conditions:

(cid:1) Your vehicle and the vehicle ahead are cruising at almost the same speed. (cid:1) The vehicle ahead is cruising at a faster speed than yours. (The distance between the vehicles will become longer.) (cid:1) The accelerator pedal is depressed, immediately after the release of the accelerator pedal or immediately after the speed

setting.

(cid:2) Depending on the road configuration (curved roads) or your vehicle condition (steering wheel maneuvering, position in

the lane), vehicles in other lanes or surrounding objects will be detected.

- 4 -

See Owner’s Manual for Complete Information.

(cid:3) Warning Display If dynamic laser cruise control detects bad weather or malfunction of the system, the master warning light comes on and the alarm sounds, and one of the warning codes “C1”, “C2” or “E3” will appear on the display.

“CRUISE” indicator light

Master Warning Light

O004qrg

Warning code

Warning code

Conditions

C1

C2

E3*

Laser radar sensor glass is dirty

(cid:1) Wipers are operating at high or low speeds (cid:1) Direct sunlight from front (cid:1) It is difficult to make a measurement

because of bad weather

System malfunction has been detected

* : “CRUISE” indicator light also flashes.

If a warning message appears on the display, take the appropriate measure referring to Section 1−7, “Owner’s Manual”.

(cid:3) Approach Warning Dynamic laser cruise control and approach warning do not operate when the vehicle ahead is at a stop or is driving much slower than your vehicle. Use caution for the vehicle at the end of the line in heavy traffic or at the tollgate, the vehicle at a stop and the very slow vehicle. If your vehicle approaches the vehicle ahead because of insufficient braking when the vehicle ahead decelerates abruptly or when another vehicle cuts in ahead of you, the display flashes and beeps. Depress the brake pedal to slow down, ensuring sufficient vehicle−to−vehicle distance.

O006

- 5 -

(cid:3) Operation Procedure The operation procedure is shown as follows. For the detailed information, see Section 1−7 in the “Owner’s Manual”. (cid:2) Setting 1 Push the “ON−OFF” button to turn on the system. The “CRUISE” and “READY” indicator lights in the instrument cluster come on.

O007

O008

2 Bring your vehicle to the desired speed. 3 Press the control lever downward in the “− SET” direction and release it. This sets the vehicle at that speed. If a vehicle is detected ahead of you: Your cruising speed changes in proportion to the speed of the vehicle ahead to maintain an appropriate distance from your vehicle to the vehicle ahead. If there was no vehicle ahead, your cruising speed will be gradually increased up to the preset speed. If no vehicle is detected ahead of you: Your cruising speed is maintained at the preset speed. (cid:2) Cancelling

To stop the operation: Pressing the “ON−OFF” button. To stop the operation temporarily: Pull the lever in the “CANCEL” direction. Depressing the brake pedal. To resume follow−up cruising or cruising at fixed speed, press the control lever upward and release it.

O009

O010

See Owner’s Manual for Complete Information.

- 6 -

(cid:3) Operation Procedure (cid:2) Acceleration/Deceleration

To accelerate: Depress the accelerator pedal. (When you release the accelerator pedal, follow−up cruising or fixed speed cruising resumes.) If there was no vehicle ahead, the vehicle will accelerate gradually to the preset speed. At this time, depressing the accelerator pedal or pressing the control lever upward and releasing it will accelerate quickly. To decelerate: Depress the brake pedal. (Even when you release the brake pedal, dynamic laser cruise control does not return to follow−up cruising or fixed speed cruising. Press the control lever upward to resume follow−up−cruising or fixed speed cruising.)

(cid:2) Changing the preset speed

Using the control lever:

1 Press the control lever upward or downward.

(cid:1) Press the control lever upward in the “+ RES” direction to increase the preset speed. (cid:1) Press the control lever downward in the “− SET” direction to decrease the preset

speed.

The displayed speed will increase or decrease every 5 mph.

2 Release the control lever when the display shows the desired preset speed.

O011

To increase the preset speed

To decrease the preset speed

Using the accelerator and brake pedals:

1 Depress the accelerator or brake pedal to attain the desired speed. 2 Press the control lever downward in the “− SET” direction and release the lever.

O008

- 7 -

00/06/06

(cid:3) Operation Procedure (cid:2) To restore the previous control

If the preset speed has been cancelled, when you press the lever upward in the “+ RES” direction while “READY” shows up on the instrument cluster and at a vehicle speed of about more than 40 km/h (25 mph), the speed set prior to cancellation will be restored.

O012

(cid:2) Changing vehicle−to−vehicle distance setting

You can select one of the following vehicle−to−vehicle distances: LONG, MIDDLE or SHORT. Each time you push the distance switch briefly, the setting changes from LONG to MIDDLE to SHORT and then back to LONG. You can confirm the setting on the display.

LONG

MIDDLE

SHORT

O005qrg

O013

O014

O015

See Owner’s Manual for Complete Information.

- 8 -

In addition to the vehicle−to−vehicle distance control mode described in this quick reference guide, dynamic laser cruise control has conventional (fixed speed) cruise control mode for cruising at fixed speeds. For the conventional (fixed speed) cruise control mode, see Section 1−7 in the “Owner’s Manual”. (cid:2) Changing to the conventional (fixed speed) control mode 1 Push the “ON−OFF” button to turn on the system. The

(cid:2) Each mode display

“CRUISE” and “READY” indicator lights in the instrument cluster come on.

The control system in the vehicle−to−vehicle distance control mode differs from the one in the conventional (fixed speed) cruise control mode. When using dynamic laser cruise control, make sure which mode is selected.

O007

Displays in the instrument cluster:

Vehicle−to−Vehicle Distance Control Mode

Fixed Speed Control Mode

2 Push the control lever in the “MODE” direction for longer

than 1 second to change to conventional cruise control mode. The “NORM.” indicator light in the instrument cluster comes on.

O016

O012

O017

O018

O019

- 9 -

00/06/06

Foreword

Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build. This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the following pages carefully. When it comes to service, remember that your Toyota dealer knows your vehicle very well and is interested in your complete satisfaction. Your Toyota dealer will provide quality maintenance and any other assistance you may require. If there is not a Toyota dealer near you, please call the following number: U.S. OWNERS:

(cid:1) When traveling in the U.S. mainland or Canada:

Toyota Customer Experience Center

Toll−free:1−800−331−4331

(cid:1) Hawaii:

Servco Automotive Customer Services

Toll−free:1−888−272−5515

CANADIAN OWNERS:

(cid:1) When traveling in Canada or the U.S. mainland:

Toyota Canada Customer Interaction Centre

Toll−free:1−888−TOYOTA−8 or 1−888−869−6828
Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also. All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of continual product improvement, we reserve the right to make changes at any time without notice. Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle. Please access our websites for further information. (cid:1) The U.S. mainland (cid:1) Hawaii (cid:1) Canada

www.toyota.com www.toyotahawaii.com www.toyota.ca

 2006 TOYOTA MOTOR CORPORATION All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.

Quick index (cid:1) If a service reminder indicator or warning buzzer comes on (cid:1) If your vehicle will not start (cid:1) If your engine stalls while driving (cid:1) If your vehicle overheats (cid:1) If you have a flat tire (cid:1) If your vehicle needs to be towed (cid:1) Tips for driving during break−in period (cid:1) How to start the engine (cid:1) General maintenance (cid:1) Complete index Gas station information Fuel type:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

145
314
318
319
320
330
266
296
343
NO TAG

UNLEADED gasoline, Octane Rating 87 (Research Octane Number 91) or higher. For improved vehicle performance, use premium unleaded gasoline with an Octane Rating of 91 (Research Octane Number 96) or higher. See page 266 for detailed information.

Fuel tank capacity:

70 L (18.5 gal., 15.4 Imp. gal.)

Engine oil:

ILSAC multigrade engine oil is recommended. See page 357 for detailed information.

Tire information: See pages 361 through 369. Tire inflation pressure: See page 386.

aU-3

Publication No. OM41418U Part No. 01999-41418
Printed in Japan 01−0608−00

( U)

Important information about this manual

Safety and vehicle damage warnings

Safety symbol

Throughout this manual, you will see safety and vehicle dam- age warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows:

CAUTION

This is a warning against anything which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to reduce the risk of injury to yourself and others.

NOTICE

This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.

ii

the safety symbol When you see shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.

Important information about your Toyota

Occupant restraint systems

Toyota encourages you and your family to take the time to read Section 1−3 of this Owner’s Manual carefully. In terms of helping you understand how you can receive the maximum benefit of the occupant restraint systems this vehicle pro- vides, Section 1−3 of this Owner’s Manual is the most impor- tant Section for you and your family to read. Section 1−3 describes the function and operation concerning seats, seat belts, SRS airbags and child restraint systems of this vehicle and some potential hazards you should be aware of. These systems work together along with the overall struc- ture of this vehicle in order to provide occupant restraint in the event of a crash. The effect of each system is enhanced when it is used properly and together with other systems. No single occupant restraint system can, by itself, provide you or your family with the equal level of restraint which these sys- tems can provide when used together. That is why it is im- portant for you and your family to understand the purpose and proper use of each of these systems and how they re- late to each other.

The purpose of all occupant restraint systems is to help re- duce the possibility of death or serious injury in the event of a collision. None of these systems, either individually or to- gether, can ensure that there is no injury in the event of collision. However, the more you know about these systems and how to use them properly, the greater your chances be- come of surviving an accident without death or serious injury. Seat belts provide the primary restraint to all occupants of the vehicle, and every occupant of the vehicle should wear seat belts properly at all times. Children should always be secured in child restraint systems that are appropriate for their age and size. SRS (Supplemental Restraint System) air- bags are, as their names imply, designed to work with, and be supplemental to, seat belts and are not substitutes for them. SRS airbags can be very effective in reducing the risk of head, chest and knee injuries by preventing contact of the head, chest and knee with interior portions of the vehicle.

iii

In order to be effective, the SRS airbags must deploy with tremendous speed. The rapid deployment of the SRS airbags makes the SRS airbags themselves potential sources of death or serious injury if an occupant is too close to an airbag, or if an object or some part of his or her body has been placed between the occupant and the airbag at the time of deployment. This is just one example of how the instruc- tions in Section 1−3 of this Owner’s Manual will help ensure proper use of the occupant restraint systems, and increase the safety they can provide to you and your family in the event of an accident. Toyota recommends you to read the provisions in Section 1−3 carefully and refer to them as needed during your time of ownership of this vehicle.

Event data recorder

Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is a system to record data in a crash or a near car crash event. This is called an Event Data Recorder (EDR). The SRS airbag sensor assembly contains the EDR. In a crash or a near car crash event, this device may record some or all of the following information:

(cid:1) Engine speed (cid:1) Whether the brake pedal was applied or not (cid:1) Vehicle speed (cid:1) To what extent the accelerator pedal was depressed (cid:1) Position of the transmission selector lever (cid:1) Whether the driver and front passenger wore the seat

belts or not

(cid:1) Driver’s seat position (cid:1) Front passenger’s occupant classification (cid:1) SRS airbag deployment data

iv

Toyota will not disclose the data recorded in an EDR to a third party except when:

(cid:1) An agreement from the vehicle’s owner (or the leasing

company for a leased vehicle) is obtained

(cid:1) Officially requested by the police or other authorities (cid:1) Used as a defense for Toyota in a law suit (cid:1) Ordered by the court

However, if necessary Toyota will:

(cid:1) Use

the data

for research on Toyota vehicle safety

performance

(cid:1) Disclose the data to a third party for research purposes without disclosing details of the vehicle owner, and only when it is deemed necessary

(cid:1) Disclose summarized data cleared of vehicle identifica- tion information to a non−Toyota organization for re- search purposes

(cid:1) SRS airbag system diagnostic data

If your vehicle is equipped with a vehicle stability control (VSC) system, its Electronic Control Unit (ECU) may contain another EDR. There are a variety of driving situations which include activating the VSC under which the VSC EDR will record certain information. The VSC EDR may record some or all of the following information:

(cid:1) Behavior of the vehicle (cid:1) Steering wheel angle (cid:1) Vehicle speed (cid:1) To what extent the accelerator pedal was depressed (cid:1) To what extent the brake pedal was applied (cid:1) To what extent the ECU controlled the condition of the

4 wheels

(cid:1) Vehicle stability control system diagnostic data

The information above is intended to be used for the purpose of improving vehicle safety performance. Unlike general data recorders, the EDR does not record sound data such as conversation between passengers.

New vehicle warranty

Your new vehicle is covered by the following Toyota limited warranties:

(cid:1) New vehicle warranty

(cid:1)

Emission control systems warranty

(cid:1) Others

For further information, please refer to the “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.

Your responsibility for

maintenance

It is the owner’s responsibility to make sure that the speci- fied maintenance is performed. Section 6 gives details of these maintenance requirements. Also included in Section 6 is general maintenance. For scheduled maintenance in- formation, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

Important health and safety

information about your Toyota

CAUTION

(cid:1) WARNING: Engine exhaust, some of its constitu- ents, and a wide variety of automobile compo- nents contain or emit chemicals known to the State of California to cause cancer and birth de- fects and other reproductive harm. In addition, oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproduc- tive harm.

lead and

(cid:1) Battery posts, terminals and related accessories contain lead compounds. Wash your hands after handling. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing thoroughly with soap and water.

vi

Accessories, spare parts and modification of your Toyota

A wide variety of non−genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replace- ment, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle. This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.

Spark ignition system of your

Toyota

The spark ignition system in your Toyota meets all require- ments of the Canadian Interference−Causing Equipment Stan- dard.

Installation of a mobile two−way

radio system

As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as multiport fuel injection system/sequential multiport fuel injection system, electronic throttle control system, cruise control system, dy- namic laser cruise control system, anti−lock brake system, traction control system, vehicle stability control system, SRS airbag system and seat belt pretensioner system, be sure to check with your Toyota dealer for precautionary measures or special instructions regarding installation.

Perchlorate Material

Special handling and disposal restrictions may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. Your vehicle has components that may contain perchlorate. These components may include airbag, seat belt pretension- ers, and wireless remote control batteries.

vii

Smart key system

Scrapping of your Toyota

Users of any electrical medical devices such as implanted pacemakers should consult the manufacturer of the device for information about its operation under the influence of ra- dio waves. Radio waves could have unexpected effects on the operation of such medical devices. For details, see “Keys” on page 14 and “Smart key system” on page 27 in Section 1−2.

The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by the qualified service shop or by your Toyota dealer before you dispose of your vehicle.

Tires and loading on your

Toyota

Underinflated or overinflated tire pressure and ex- cess load may result in the deterioration of steering ability and braking ability, leading to an accident. Check the tire inflation pressure periodically and be sure to stay with the load limits given in this Owner’s Manual. For details about tire inflation pressure and load limits, see pages 289 and 361.

Leak detection pump

This pump performs fuel evaporation leakage check. This check is done approximately five hours after the engine is turned off. So you may hear sound coming from underneath the luggage compartment for several minutes. It does not indicate a malfunction.

viii

You should know as much about the quality and importance of proper maintenance of your new vehicle as the people who built it.

The Toyota authorized Repair Manual tells you how to maintain your vehicle and enables you to correctly perform your own maintenance.

The best way to keep your new vehicle in top running order is to maintain it properly from the moment you drive it off the showroom floor.

The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.

Maintenance procedures for the engine, chassis, body, electrical system, and more, are clearly explained and illustrated.

Periodic maintenance and tune-up

Periodic maintenance and tune-up helps to pre› vent small problems from growing into larger ones lat› er on. The repair manual outlines exactly what main› tenance is required and clearly explains how to do the work yourself step-by-step.

Areas covered include such things as spark plug re› placement, valve clearance adjustment and engine oil and filter replacement.

Where to obtain the

Repair Manual

The repair manual for AVALON may be pur› chased from any Toyota dealer or the Material Distribution Center. To purchase the repair manual, please contact your Toyota dealer or call the Material Distribution Center toll-free at 1-800-622-2033.

WE REALLY CARE ABOUT YOU (cid:1) PLEASE BUCKLE UP

Toyota has made a special effort to encourage use of seat belts.

Toyota belts are:

(cid:1) Comfortable (cid:1) Easy to use (cid:1) Convenient

We encourage you to use your belts every time you drive.

SECTION 1− 1

OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview Instrument cluster overview Center cluster overview Indicator symbols on the instrument panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrument panel overview (cid:1)View A

1. Side vents 2. Side defroster outlets 3. Instrument cluster 4. Center cluster 5. Garage door opener switches 6. Auxiliary boxes 7. Front personal lights, interior light and/or electric moon roof switches

8. Center vents 9. Glove box 10. Power door lock switches 11. Power window switches 12. Trunk opener main switch 13. Rear console box 14. Rear vents 15. Power outlets 16. Seat ventilator/heater switches 17. Cup holder 18. Automatic transmission selector lever 19. Tire pressure warning reset switch

(On bottom of the instrument panel)

20. Hood lock release lever 21. Parking brake pedal 22. Window lock switch 23. Driving position memory switches

(cid:1)View B (with key cylinder−type ignition switch)

1. Instrument panel light control knob 2. Headlight, turn signal and front fog

light switches

3. Audio remote control switches 4. Speech command switch (See the

separate “Navigation System Owner’s Manual.”)

5. Climate remote control switches 6. Wiper and washer switches 7. Rear window and outside rear view

mirror defogger switch

8. Emergency flasher switch 9. Audio system 10. Air conditioning controls 11. Cigarette lighter and ashtray, auxiliary

box, cassette player or navigation system controller (For the navigation system, see the separate “Navigation System Owner’s Manual.”)

12. Ignition switch 13. Cruise control switch 14. Tilt steering lock release lever 15. Telescopic steering lock release lever

16. Glass breakage sensor 17. Trunk opener switch 18. Fuel filler door opener switch 19. Power rear view mirror control switches

(cid:1)View B (with smart key system)

1. Instrument panel light control knob 2. Headlight, turn signal and front fog

light switches

3. Audio remote control switches 4. Speech command switch (See the

separate “Navigation System Owner’s Manual.”)

5. Climate remote control switches 6. Wiper and washer switches 7. Rear window and outside rear view

mirror defogger switch

8. Emergency flasher switch 9. Audio system 10. Air conditioning controls 11. Cigarette lighter and ashtray, auxiliary

box, cassette player or navigation system controller (For the navigation system, see the separate “Navigation System Owner’s Manual.”)

12. Ignition switch (engine switch) 13. Cruise control switch 14. Distance switch 15. Tilt steering lock release lever

16. Telescopic steering lock release lever 17. Glass breakage sensor 18. Rear electric sunshade switch 19. Trunk opener switch 20. Fuel filler door opener switch 21. Power rear view mirror control switches

Instrument cluster overview

1. Engine coolant temperature gauge 2. Service reminder indicators and

indicator lights

3. Tachometer 4. Speedometer

5. Fuel gauge 6. Low fuel level warning light 7. Trip meter reset knob 8. Odometer and two trip meters

9. Automatic transmission shift range

position display

10. Dynamic laser cruise control display 11. Dynamic laser cruise control master

warning light

Center cluster overview

1. Clock 2. Center display* 1