2008 Toyota Sienna Owners Manual

08 SIENNA_U (L/O 0801)

SECTION 1− 1

OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview Instrument cluster overview Indicator symbols on the instrument panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Instrument panel overview

1. Side defroster outlets 2. Side vents 3. Instrument cluster 4. Center vents 5. Multi−information display or garage

door opener box

6. Auxiliary boxes 7. Glove box 8. Power window switches 9. Power door lock switches 10. Seat heater dials or auxiliary box 11. Cup holder and coin holder 12. Power outlets 13. Automatic transmission selector lever 14. Tire pressure warning system reset

switch

15. Power sliding door main switch

(“SLIDE DOOR OFF” switch)

16. Parking brake pedal 17. Window lock switch 18. Driving position memory buttons 19. Hood lock release lever 20. Power back door main switch

(“BACK DOOR OFF” switch)

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

1. Headlight, turn signal and front fog

light switches

2. Wiper and washer switches 3. Rear window and outside rear view

mirror defogger and windshield wiper de−icer switch

4. Emergency flasher switch 5. Audio system or rear view monitor system/navigation system including audio system (For the navigation system, see the separate “Navigation System Owner’s Manual”.) 6. Power outlet main switch 7. AUX adapter 8. Air conditioning controls 9. “AIR BAG ON” and “AIR BAG OFF”

indicator lights

10. Toyota park assist system switch and

indicator light

11. Personal light main switch 12. Engine switch 13. “TRAC OFF” switch 14. Cruise control switch or dynamic laser

cruise control switch

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

"Overhead console

"Steering switches

15. Tilt and telescopic steering lock release

lever

16. Power rear view mirror control switches 17. “REAR VENT” switch 18. Headlight beam level control dial

1. Conversation mirror 2. Power back door switch 3. Front personal lights 4. Power sliding door switches 5. Electric moon roof switch 6. Microphone

1. Volume control switches for audio

system/hands−free system

2. “ƜƝ” switch 3. “MODE” switch 4. Telephone switches 5. Distance switch 6. Talk switch

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Instrument cluster overview "Type A

1. Service reminder indicators and

indicator lights

2. Speedometer 3. Engine coolant temperature gauge

4. Low fuel level warning light 5. Fuel gauge 6. Trip meter reset knob/instrument panel

light control knob

7. Odometer and two trip meters 8. Tachometer

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

"Type B

1. Service reminder indicators and

indicator lights

2. Speedometer 3. Engine coolant temperature gauge 4. Low fuel level warning light

5. Fuel gauge 6. Dynamic laser cruise control master

warning light

7. Dynamic laser cruise control display

8. Trip meter reset knob/instrument panel

light control knob

9. Odometer and two trip meters 10. Tachometer

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Indicator symbols on the instrument panel

or

Brake system warning light∗1

or

Anti−lock brake system warning light∗1

Driver’s seat belt reminder light∗1

Open door warning light∗1

Front passenger’s seat belt reminder light∗1

SRS warning light∗1

Charging system warning light∗1

or

Malfunction indicator lamp∗1

Low engine oil pressure warning light∗1

Vehicle stability control system/traction control system warning light∗1

Low tire pressure warning light∗1

Low windshield washer fluid level warning light∗1
Engine oil replacement reminder light∗1 (for vehicles sold in U.S.A.)

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Third seat warning light∗1

Slip indicator light

Engine immobilizer/theft deterrent system indicator light

“AIR BAG ON” indicator light

“AIR BAG OFF” indicator light

Traction control system off indicator light (two−wheel drive models) Cruise control indicator light∗2 or dynamic laser cruise control indicator light∗3

Dynamic laser cruise control ready mode indicator light

Headlight indicator light

Conventional cruise control mode indicator light

Tail light indicator light

Headlight high beam indicator light

Turn signal indicator lights

Automatic transmission indicator lights

∗1: For details, see “Service reminder indicators and warning

buzzers” on page 191 in Section 1−6.

∗2: If this light flashes, see “Cruise control” on page 222 in

Section 1−7.

∗3: If this light flashes, see “Dynamic laser cruise control” on

page 225 in Section 1−7.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

SECTION 1− 2

OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys Engine immobilizer system Wireless remote control Front doors Sliding doors Power sliding doors Back door Power back door Power windows Manual quarter windows Power quarter windows Hood Theft deterrent system Fuel tank cap Electric moon roof

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10
13
14
22
25
28
36
38
43
46
47
48
49
51
53

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Keys (without engine immobilizer system)

Keys (with engine immobilizer system)

KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.

Your vehicle is supplied with two kinds of keys. 1. Master keys—These keys work in ev-

ery lock.

2. Sub key—This key will not work in the

glove box.

To protect items locked in the glove box when using valet parking, leave the sub key with the attendant. Since the front doors and sliding doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.

10

Your vehicle is supplied with two kinds of keys. 1. Master keys (black)—These keys work in every lock. Your Toyota dealer will need one of them to make a new key with a built−in transponder chip.

2. Sub key (gray)—This key will not work

in the glove box.

A transponder chip for engine immobilizer system has been placed in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

To protect items locked in the glove box when using valet parking, leave the sub key with the attendant. Since the front doors and sliding doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.

NOTICE

the

When using a key containing a trans- ponder chip, observe following precautions: z When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.

z When starting the engine, do not use the key with other transponder keys around (including keys of oth- er vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after remov- ing other transponder keys (includ- ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.

11

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

z Do not cover the key grip with any material that cuts off electromagnet- ic waves.

z Do not knock the key hard against

other objects.

z Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under direct sunlight. z Do not put the key

in water or

wash it in an ultrasonic washer.

z Do not bend the key grip.

z Do not use the key with electromag-

netic materials.

12

KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Engine immobilizer system

in

immobilizer system

The engine is a theft prevention system. When you in- sert the key in the engine switch, the transponder chip the key’s head transmits an electronic code to the ve- hicle. The engine will start only when the electronic code in the chip corre- sponds to the registered ID code for the vehicle. Never leave the keys inside the vehicle when you leave the vehicle.

indicator

light will start

The system is automatically set when the key is removed from the engine switch. On some models— The show the system is set. If any of the following indicator conditions occurs, contact your Toyota dealer. D The

light stays on except when the theft deterrent system is set- ting or activating. (See “Theft deterrent system” on page 49 in this Section.)

flashing to

indicator

D The indicator light does not start flash- ing when the key is removed from the engine switch.

D The indicator light flashes inconsistent-

ly.

Inserting the registered key in the engine switch automatically cancels the system, which enables the engine to start. The indicator light will go off. The system is maintenance−free. For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you. If you make your own duplicate key, you will not be able to cancel the sys- tem or start the engine.

NOTICE

remove or disas- Do not modify, semble the engine immobilizer sys- tem. If any unauthorized changes or modifications are made, proper opera- tion of the system cannot be guaran- teed.

13

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

For vehicles sold in U.S.A.

For vehicles sold in Canada

Wireless remote control—

This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.

interference,

including

FCC ID: MOZ RI−21BTY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.

CAUTION

Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.

14

Type A

Type B

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

1. Lock switch 2. Unlock switch 3. Alarm switch 4. Sliding door open switch (right side) 5. Back door open switch 6. Sliding door open switch (left side)

08 SIENNA_U (L/O 0801)

The wireless remote control system is designed to lock or unlock all the side doors and back door, or activate the panic mode from a distance within approximately 1 m (3 ft.) of the vehicle. On some models, the system also al- lows you to activate the theft deterrent system from the same distance. When you operate any switch, push slowly and securely. The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause damage remote control to transmitter. D Do not leave the transmitter in places the temperature becomes high

the wireless

where such as on the dashboard.

it

D Do not disassemble it. D Avoid knocking

it hard against other

objects or dropping it.

D Avoid putting it in water. You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information.

transmitters

for

If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: D Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.

D The battery may have been consumed. Check the battery in the transmitter. To replace the battery, see “—Replacing battery” on page 20.

If you lose your wireless remote control transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” on page 493 in Section 4.)

MADE IN U.S.A. This complies with Part 15 of the FCC rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.

15

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

—Locking and unlocking doors

Locking operation (type A)

Locking operation (type B)

Unlocking operation (type A)

Unlocking operation (type B)

16

this

To lock and unlock all the doors, push the switches of the transmitter slowly and securely. To lock: Push the lock switch. All the side doors and back door are locked simulta- neously. At time one beep will be heard, turn signal lights will flash once. Check to see that the doors are securely locked. If any of the side doors or back door is not securely closed, or if the key is in the engine switch, locking cannot be per- formed by the lock switch and a beep will sound continuously for 10 seconds. How- ever, if the key is in the engine switch, a beep will not sound. To stop the beep, close all the side doors and back door securely or push the un- lock switch. The buzzer can be disabled. For details, contact your Toyota dealer. To unlock: Push the unlock switch once to unlock only the driver’s door. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simulta- neously. Each time the unlock switch is pushed, two beeps will be heard, turn sig- nal lights will flash twice.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

This double switch operation to unlock all the side doors and back door can be changed to a single switch operation. For details, contact your Toyota dealer. When the unlock switch is pressed, the front personal lights and engine switch light come on. The lights remains on for about 15 seconds unless any of the side doors or back door are opened then and closed. (For further information, see “Front personal lights” on page 179 and/or “En- gine (ignition) switch light” on page 181 in Section 1−5.) You have 60 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will automatical- ly lock again. The lock function can be changed. For details, con- tact your Toyota dealer. is kept If pressed in, the locking or unlocking opera- tion is not repeated. Release the switch and then push again.

lock or unlock switch

the automatic door

timing

the

for

08 SIENNA_U (L/O 0801)

—Opening and closing sliding doors

The following adjustments can be made in this system. For details, contact your Toyota dealer. D Cancelling the wireless door locking or

unlocking function

D Cancelling the flash of the turn signal

lights

D Cancelling the beep sound

Right side power sliding door (type A)

Right side power sliding door (type B)

17

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

The sliding door operation by the wireless remote control can be changed or dis- abled. For details, contact your Toyota dealer.

Opening operation can be performed by the switches under the following conditions only: D The sliding door is unlocked. D The power sliding door system is on. (The “SLIDE DOOR OFF” switch on the instrument panel is pushed out.)

D The key is not in the engine switch. D The sliding door is between the fully− closed position and half−opened posi- tion.

Left side power sliding door (type B only)

the sliding door open

Push and hold the switch of the wire- less remote control transmitter about one second. The power sliding door opens and closes completely. Right side power sliding door— To open: Push switch (right side). To close: Push switch (right side) again. Left side power sliding door— To open: Push switch (left side). To close: Push switch (left side) again.

the sliding door open

the sliding door open

the sliding door open

the

fuel

The sliding door stops at the half−opened position when the window is opened more than about 15 cm (6 in.). The left side power sliding door does not operate when is opened. Closing operation can be performed by the wireless remote control switches under the following conditions only: D The power sliding door system is on. (The “SLIDE DOOR OFF” switch on the instrument panel is pushed out.)

filler door

D The key is not in the engine switch. D The sliding door is between the fully− opened position and half−opened posi- tion.

18

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

—Opening and closing back door (type B only)

—Activating alarm

Opening operation can be performed by the switch under the following conditions only: D The back door is unlocked. D The power back door system

is on. (The “BACK DOOR OFF” switch on the instrument panel is pushed out.)

D The key is not in the engine switch. D The back door is between the fully− closed position and half−opened posi- tion.

Closing operation can be performed by the switch under the following conditions only: D The power back door system is on. (The “BACK DOOR OFF” switch on the instrument panel is pushed out.)

D The key is not in the engine switch. D The back door is between the fully− opened position and half−opened posi- tion.

The back door operation by the wireless remote control can be changed or dis- abled. For details, contact your Toyota dealer.

Push and hold the back door open switch on the wireless remote control transmitter for about one second. The power back door opens and closes completely. When closing or opening the back door, two beeps will be heard and the turn sig- nal lights will flash twice.

the horn

Pushing and holding the alarm switch blows intermittently and flashes the headlights, tail lights and turns on the front personal lights. The alarm switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, do the following: D Push any of the switch on the wireless

remote control transmitter.

D Lock or unlock either front doors or

back door with the key.

D Turn

the engine switch

from

the

“LOCK” to “ON” position.

19

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

The alarm does not work when the engine switch is in the “ON” position. This alarm function can be disabled. For details, contact your Toyota dealer.

—Replacing battery For replacement, use a CR2032 lithium battery or equivalent.

CAUTION

Special care should be taken to pre- vent small children from swallowing the removed transmitter battery or components.

NOTICE

z When replacing the transmitter bat- tery, be careful not to lose the com- ponents.

z Replace only with

the same or equivalent type recommended by a Toyota dealer.

z Dispose of used batteries according

to the local laws.

Replace the transmitter battery by follow- ing these procedures:

1. Using a coin or equivalent, open the

transmitter case.

20

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

z Be careful not to bend the electrode when inserting the transmitter bat- tery and that dust or oils do not adhere to the transmitter case.

z Close the transmitter case securely.

replacing battery, check

the After transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.

that

2. Remove the discharged transmitter bat-

3. Put in a new transmitter battery with

tery.

NOTICE

Do not bend the terminals.

positive (+) side up.

Close the transmitter case securely.

NOTICE

z Make sure

the positive side and negative side of the transmitter bat- tery are faced correctly.

z Do not replace the battery with wet hands. Water may cause unexpected rust.

z Do not touch or move any compo- nents inside the transmitter, or it may interfere with proper operation.

21

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Front doors—

When either front door is unlocked with a key, the front personal lights and engine switch light will come on and remain on for about 15 seconds before fading out. (For details, see “Front personal lights” on page 179 and “Engine (ignition) switch light” on page 181 in Section 1−5.)

LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. All the side doors and back door lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice the doors simultaneously. This double key turning operation to un- lock all the side doors and back door can be changed to a single key turning opera- tion. For details, contact your Toyota deal- er.

in succession will unlock all

22

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. The front doors can be opened by pulling the inside handles even if the lock knobs are in the locked position.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

CAUTION

Do not pull the inside handle of the front doors while driving. The doors will open and an accident may occur. Toyota strongly recommends that all children be placed in the rear seat of the vehicle.

Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. The front doors cannot be locked if you leave the key in the engine switch.

Driver’s side

Front passenger’s side

08 SIENNA_U (L/O 0801)

lock: Push the switch down on the

LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To front side. To unlock: Push the switch down on the rear side. Operating the switch simultaneously locks or unlocks all the side doors and back door. If you do either of the following, no side door or back door can be unlocked with the power door lock switch. D Lock all the side doors and back door with the key or wireless remote control transmitter when all the side doors and back door are closed.

D Open the driver’s door or front passen- ger’s door and move the inside lock knobs of both front doors to the lock position, then close the front doors.

23

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

The power door lock switch can be reset in the following ways. D Turn the engine switch to “ON”. D Unlock all

the side doors and back door with the key or wireless remote control transmitter.

D Unlock the driver’s door or front pas- lock the doors the power door

senger’s door with knob, and then unlock all and back door with lock switch.

inside

the

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle in an accident. It also helps pre- vent the doors from being opened unintentionally.

24

08 SIENNA_U (L/O 0801)

—Automatic door locking and unlocking functions AUTOMATIC DOOR LOCKING You can select the following functions: D Locking linked with the shift position All doors are automatically locked when the selector lever is moved out of “P” position.

D Locking linked with vehicle speed

All doors are automatically locked when the vehicle speed goes above about 20
km/h (12 mph).

You can set or cancel the automatic door locking functions: Be sure to apply the parking brake when performing the following operations. To select the locking linked with the shift position: 1. Close all doors and turn the engine

switch to the “ON” position.

2. Shift the selector lever to the “P” posi-

tion.

3. Within 10 seconds of turning the en- gine switch to the “ON” position, press and hold the driver’s side power door lock switch in the lock position for 5
seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again. To select the locking linked with the vehicle speed: 1. Close all doors and turn the engine

switch to the “ON” position.

2. Shift the selector lever from “P” to the

“N” position.

3. Within 10 seconds of turning the en- gine switch to the “ON” position, press and hold the driver’s side power door lock switch in the lock position for 5
seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

AUTOMATIC DOOR UNLOCKING You can select the following functions: D Unlocking linked with the shift posi-

tion All doors are automatically unlocked when the selector lever is moved to “P” position.

D Unlocking

linked with

the engine

switch All doors are automatically unlocked when the driver’s door is opened within 10 seconds after the engine switch is turned to the “ACC” or “LOCK” posi- tion, or the key is removed.

You can set or cancel the automatic door unlocking functions: Be sure to apply the parking brake when performing the following operations. To select the unlocking linked with the shift position: 1. Close all doors and turn the engine

switch to the “ON” position.

2. Shift the selector lever to the “P” posi-

tion.

08 SIENNA_U (L/O 0801)

Sliding doors (non−powered)

3. Within 10 seconds of turning the en- gine switch to the “ON” position, press and hold the driver’s side power door lock switch in the unlock position for 5 seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again. To select the unlocking linked with the engine switch: 1. Close all doors and turn the engine

switch to the “ON” position.

2. Shift the selector lever from “P” to the

“N” position.

3. Within 10 seconds of turning the en- gine switch to the “ON” position, press and hold the driver’s side power door lock switch in the unlock position for 5 seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again.

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Move the knob forward. To unlock: Move the knob backward. Closing the sliding door with the lock knob in the lock position will also lock the slid- ing door. Be careful not to lock your keys in the vehicle.

25

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

CLOSING THE FULLY−OPENED SLIDING DOOR To close the fully−opened sliding door, pull the then close the door.

inside or outside handle and

Sliding door closer (on some models): When the sliding door has not been fully closed, is automatically closed com- pletely even if the power sliding door sys- tem is off.

it

CAUTION

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps from being prevent thrown out from the vehicle in an accident. It also helps prevent the doors from being opened unintention- ally.

the passengers

26

D Careful attention is needed so as not to get your fingers trapped as the automatically closes when it has not been fully closed.

sliding

door

D Never allow a child to operate the

sliding door.

NOTICE

Do not apply excessive force when the sliding door closer is operating. Otherwise, the sliding door closer may be damaged.

CAUTION

D When closing the sliding door, con- firm safety of the area around. Keep the heads, hands and other parts of the bodies of all occupants away from the sliding door. Other- wise, the closing door may cause death or serious injury.

the door will slide

D When the vehicle is stopped on a slope, faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

the door

D When stopping on a downward slope, open fully while passengers are getting on or off. Do not pull the outside handle or inside handle while is open as the door could suddenly close by itself causing injury.

the door

NOTICE

Do not close the sliding door by ap- plying the brakes. Doing so could cause the door to be damaged.

When the fuel filler door is opened, the left side sliding door will not open. Close the fuel filler door securely and then operate the sliding door.

NOTICE

Avoid forcibly opening the left side sliding door fully when the fuel filler door is opened. Otherwise, the fuel filler door may be damaged.

the sliding door window

When is opened more than about 15 cm (6 in.), the sliding door will stop at half− opened position reasons. Close the window and then operate the sliding door.

for safety

CAUTION

latched at this position.

Do not leave the sliding door at half− opened position because the door is not If the vehicle is stopped on a downward slope, it may move and cause an un- expected injury.

27

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Power sliding doors—

On

Off

SLIDING DOOR CHILD−PROTECTORS Open the sliding door fully and move the lock lever to the “LOCK” position as shown on the label. Then close the sliding door. If the child−protector is locked, you cannot open the sliding door from the inside. We recommend using feature whenever small children are in the vehicle.

this

POWER SLIDING DOOR MAIN SWITCH (“SLIDE DOOR OFF” switch) This switch is used to turn on and off the power sliding door system. In order to operate the power sliding door, the “SLIDE DOOR OFF” switch on the in- strument panel must be pushed out. (The orange line on top of the switch indicates that the power sliding door system is on.) To disable the power sliding door feature, push in the switch.

28

When the power sliding door system is on, you can open and close the sliding door with the power sliding door switches on the overhead console or wireless re- mote control transmitter even if the sliding door child−protector is locked. When the power sliding door system is off, you can open and close the sliding door by the same operations as non−pow- ered sliding door. The sliding door closer is operative even if the power sliding door system is off. See page 32 about sliding door closer.

CAUTION

D Do not leave small children or pets in your vehicle. They unattended could operate the power sliding door and injure themselves or oth- ers. Turn off the power sliding door system when the power sliding door is not in use.

D When jacking up the vehicle, turn off the power sliding door system and close the sliding door com- pletely.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

NOTICE

When your vehicle goes through an automatic car wash, make sure the power sliding door system is off.

08 SIENNA_U (L/O 0801)

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Move the knob forward. To unlock: Move the knob backward. Closing the sliding door with the lock knob in the lock position will also lock the slid- ing door. Be careful not to lock your keys in the vehicle.

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of locking the doors helps seat belts, prevent from being thrown out from the vehicle in an accident. It also helps prevent the doors from being opened unintention- ally.

the passengers

29

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

—Operation of power sliding door The power sliding door can be operated automatically in the following ways: D Operates with the power sliding door

switches inside the vehicle

D Operates with the wireless remote con-

trol transmitter

D Assists operation with the outside or

inside handle by hand

the

The power sliding door system can be canceled by “SLIDE DOOR OFF” switch. When the power sliding door system is on, if you put the transmission out of “P” with the engine switch in the “ON” posi- tion and the sliding door is not completely closed, a buzzer will sound.

CAUTION

D Careful attention is needed so as not to get your fingers trapped as the sliding door automatically opens or closes.

D Never allow a child to operate the

sliding door.

30

08 SIENNA_U (L/O 0801)

NOTICE

Do not apply excessive force when the sliding door is operated automati- cally. Otherwise, the power sliding door system may be damaged.

You can cause a beep to sound when the power sliding door is opened or closed. For details, contact your Toyota dealer.

Front overhead console (type A)

Front overhead console (type B)

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Switches on the center pillar:

“PWR DOOR” switch—To operate each side door

Opening operation can be performed by the switches under the following condi- tions: D The sliding door is unlocked. D The power sliding door system is on. is

“SLIDE DOOR OFF” switch

(The pushed out.)

D The sliding door is between the fully− closed position and half−opened posi- tion.

D When the engine switch is in the “ON” position, the transmission selector lever must be in “P”.

D The

child−protector

is

unlocked.

(switches on the center pillar only)

Center pillar

OPERATING WITH THE POWER SLIDING DOOR SWITCHES To open the door, push the switch. To close the door, push the switch once again. The door opens and closes com- pletely. Switches on the front overhead con- sole:

” switch—To operate

“ door (type B only)

the

left side

” switch—To operate the right side

“ door

Closing operation can be performed by the switches under the following condi- tions: D The power sliding door system is on. is

“SLIDE DOOR OFF” switch

(The pushed out.)

D The sliding door is between the fully− opened position and half−opened posi- tion.

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened. The length of time required to push the switches for operating the sliding door can be changed. For details, contact your Toyota dealer.

CAUTION

If you shift the automatic transmis- sion selector lever out of “P” and accelerate before the power sliding door is closed completely, the sliding door may reverse to the open posi- tion. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you start driving.

31

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

” or “

THE WIRELESS

OPERATING WITH REMOTE CONTROL TRANSMITTER To open or close the door, push the ” switch on the wireless “ remote control transmitter about one second. (Only when the power sliding door system is on.) For details, see “Wireless remote control” on page 14
in this Section. ASSISTS THE OUTSIDE OR INSIDE HANDLE BY HAND When the power sliding door system is on (the “SLIDE DOOR OFF” switch is pushed out), if you pull the outside handle or slide the the sliding door will automatically and completely open or close. When the power sliding door system is off, the sliding door can be operated manually by the outside or inside handle.

OPERATION WITH

inside handle,

08 SIENNA_U (L/O 0801)

inside or outside handle and

CLOSING THE FULLY−OPENED SLIDING DOOR To close the fully−opened sliding door, pull the then close the door. Sliding door closer: When the sliding door has not been fully closed, it is auto- matically closed completely even the power sliding door system is off.

if

CAUTION

D Careful attention is needed so as not to get your fingers trapped as the automatically closes when it has not been fully closed.

sliding

door

D Never allow a child to operate the

sliding door.

NOTICE

Do not apply excessive force when the sliding door closer is operating. Otherwise, the sliding door closer may be damaged.

JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power sliding door while it is closing or opening, the sliding door will automatically reverse to the opposite di- rection. However, if the power sliding door is between fully− opened positions while it is opening, the door will stop at that position. If function operates continuously at the closing operation more the sliding door will be than 2 stopped at that position and the power sliding door system will be canceled.

the half−opened and

jam protection

times,

the

32

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Before operating the power sliding door, make sure there is nobody near the slid- ing door. Make sure the sliding door stops at the fully−opened position, and then al- low the passengers to get in and out of the vehicle. The resistance must be as strong as the force of the moving door, or stronger. As the sliding door approaches fully− closed or fully−opened position, its moving force increases significantly. The jam protection function may not work if something gets caught just before the sliding door is fully closed. If the sliding door receives a strong im- pact, this function may operate even if nothing is caught.

the

D The

jam protection

function may not work if something gets caught just before the sliding door is fully closed.

D Before you close the power sliding door, always make sure there is no- body around it. Also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught in a closing door, it could result injury. When anyone closes the power slid- ing door, make sure he or she oper- ates the door safely.

in death or serious

the vehicle.

inside

In any of

the battery.

If the battery is disconnected or run down, the power sliding door system may not work after you reconnect, replace or recharge these cases, close the sliding doors completely by hand to normalize the power sliding door system. If the power sliding door system does not operate properly after the above proce- dure, there may be a problem in the sys- tem. Contact your Toyota dealer.

CAUTION

NOTICE

The power sliding door could injure people if they are caught in the door path. When using the power sliding door, observe the following: D Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in death or serious injury.

Objects caught in the path of the slid- ing door may be damaged. Make sure there is nothing in the doorway be- fore closing the sliding door.

33

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

—Power sliding door cautions

CAUTION

D When closing the sliding door, con- firm safety of the area around. Keep the heads, hands and other parts of the bodies of all occupants away from the sliding door. Other- wise, the closing door may cause death or serious injury.

the door will slide

D When the vehicle is stopped on a slope, faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door.

34

the door

D When stopping on a downward slope, open fully while passengers are getting on or off. Do not pull the outside handle or inside handle while is open as the door could suddenly close by itself causing injury.

the door

NOTICE

Do not close the sliding door by ap- plying the brakes. Doing so could cause the door to be damaged.

When the fuel filler door is opened, the left side sliding door will not open. Close the fuel filler door securely and then operate the sliding door.

NOTICE

Avoid forcibly opening the left side sliding door fully when the fuel filler door is opened. Otherwise, the fuel filler door may be damaged.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

the sliding door window

When is opened more than about 15 cm (6 in.), the sliding door will stop at half− opened position reasons. Close the window and then operate the sliding door.

for safety

08 SIENNA_U (L/O 0801)

—Sliding door child−protectors

CAUTION

When the power sliding door is ON— Do not leave the sliding door at half− opened position because the door will unlock after 30 minutes. If the vehicle is stopped on a downward slope, it may move and cause an unexpected injury. When is OFF—Do not leave the sliding door at half−opened position because the door is not latched at this position. If the vehicle is stopped on a down- ward slope, it may move and cause an unexpected injury.

the power sliding door

NOTICE

When the power sliding door is ON— To prevent the battery from being dis- charged, do not leave the sliding door at half−opened position.

Open the sliding door fully and move the lock lever to the “LOCK” position as shown on the label. Then close the sliding door. When the child−protector is locked, you cannot open the sliding door by the inside door handle. We recommend using this feature whenever small children are in the vehicle.

35

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Back door (non−powered)

CAUTION

Make sure to turn off the power slid- ing door system after the child−protectors.

locking

To open the back door, push up the back door opener and raise the door. The back door can be opened when the vehicle is stopped. The back door can be locked or unlocked in the following ways. D Operate

lock switch. (See “Front doors” on page 22 in this Section.) D Operate

remote control. (See “Wireless remote control” on page 14 in this Section.)

the power door

the wireless

“Engine

(ignition) switch

When all the side doors and back door are unlocked simultaneously with a key, the front personal lights and engine switch light will come on and remain on for about 15 seconds before fading out. (For details, see “Front personal lights” on page 179
and light” on page 181 in Section 1−5.) If the back door opener does not operate, see “If you cannot operate back door opener” on page 494 in Section 4. If the battery is disconnected or run down, the back door will be automatically locked after you reconnect, replace or re- charge the battery. Be careful not to lock your keys in the vehicle.

D All the side doors and back door are locked and unlocked simultaneously with “Front doors” on page 22 in this Section.)

the driver’s door.

(See

36

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

CAUTION

Keep the back door closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.

NOTICE

To avoid damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.

Back door closer (on some models): When the back door has not been fully closed, is automatically closed com- pletely.

it

CAUTION

D Careful attention is needed so as not to get your fingers trapped as the back door automatically closes when it has not been fully closed. D Never allow a child to operate the

back door.

NOTICE

Do not apply excessive force when the back door closer is operating. Otherwise, the back door closer may be damaged.

37

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

When closing the back door, the inside strap can be used to make the reach easier. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See “—Stowage precautions” on page 447
in Section 2 for precautions when loading luggage.

08 SIENNA_U (L/O 0801)

Power back door— —“BACK DOOR OFF” switch

On

Off

This switch is used to turn on and off the power back door system. In order to operate the power back door, the “BACK DOOR OFF” switch on the in- strument panel must be pushed out. (The orange line on top of the switch indicates that the power back door sys- tem is on.) To disable the power back door feature, push in the switch.

CAUTION

D Do not leave small children or pets unattended in your vehicle. They could operate the power back door, and anyone around the back door could be injured. Turn off the power back door system when the power back door is not in use.

D When jacking up the vehicle, turn off the power back door system and close the back door completely.

NOTICE

When your vehicle goes through an automatic car wash, make sure the power back door system is off.

38

—Automatic operation (power back door—ON) The power back door can be operated automatically in the following ways: D Operates with

the power back door

switch on the overhead console

D Operates with the wireless remote con-

trol transmitter

is

the

system

canceled,

D Assists closing by hand The power back door system can be can- celed by the “BACK DOOR OFF” switch. When see “—Manual operation” on page 41 in this Section. When closing or opening the back door automatically, two beeps will be heard and the turn signal lights will flash twice. The beep sound can be changed. For de- tails, contact your Toyota dealer.

CAUTION

D Careful attention is needed so as not to get your fingers trapped as the back door automatically closes. D Never allow a child to operate the

back door.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

NOTICE

Do not apply excessive force when the back door is operated automati- cally. Otherwise, the power back door system may be damaged.

OPERATING WITH THE POWER BACK DOOR SWITCH To open the door, push and hold the ” switch on the overhead con- “ sole about one second. To close the door, push this switch once again. The door opens and closes completely.

Opening operation can be performed by the switch under the following condi- tions: D The back door is unlocked. D The power back door system

“BACK DOOR OFF” switch

is on. is

(The pushed out.)

D The back door is between in the fully− closed position and half−opened posi- tion.

D When the engine switch is in the “ON” position, the transmission selector lever must be in “P”.

Closing operation can be performed by the switch under the following condi- tions: D The power back door system

“BACK DOOR OFF” switch

is on. is

(The pushed out.)

D The back door is between in the fully− opened position and half−opened posi- tion.

The time of pushing the switches for oper- ating the back door can be changed. For details, contact your Toyota dealer.

39

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

(Only when

THE WIRELESS

OPERATING WITH REMOTE CONTROL TRANSMITTER To open or close the door, push and ” switch on the wireless hold the “ remote control transmitter about one the power back second. door system is on.) For details, see “Wireless remote control” on page 14
in this Section. ASSISTS CLOSING BY HAND When the power back door system is on (the “BACK DOOR OFF” switch is pushed out), if you move the back door about 10—15 cm (4—6 in.) from its fully−opened position, the back door will automatically and completely close. When the power back door system is off, the back door can be closed manually. The assisting function when closing the back door can be disabled and the assist- ing function when opening the back door can be added. For details, contact your Toyota dealer.

JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power back door while it is closing or opening, the back door will au- tomatically reverse to the opposite direc- tion. If function operates continuously at the closing operation more than 2 the back door will be stopped at that position.

jam protection

times,

the

Before operating the power back door, make sure there is nobody near the back door. The resistance must be as strong as the force of the moving door, or stronger. As the back door approaches the fully−closed or fully−opened position, its moving force increases significantly. The jam protection function may not work if something gets caught just before the back door is fully closed. If the back door receives a strong impact, this function may operate even if nothing is caught.

40

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

—Manual operation (power back door—OFF)

If the battery is disconnected or run down, the back door will be automatically locked and the power back door system may not work after you reconnect, replace or recharge the battery. In any of these cases, normalize the power back door system by following procedure.