2008 Toyota Sienna Owners Manual

This product is a class I laser product complied with 21 C.F.R part 1040.10
and 1040.11.

CAUTION

To ensure that dynamic laser cruise control will function properly while driving, observe the following: D Always keep the laser radar sensor glass clean. When cleaning, use a soft cloth and be careful not to damage the sensor.

D Avoid strong impacts around the la- ser radar sensor. An incorrect laser radar sensor alignment will result in system malfunction. A special de- vice is required to adjust the laser radar sensor alignment. Be sure to have the sensor adjusted by your Toyota dealer.

D Do not affix a sticker (including a transparent sticker) or attach an ac- cessory around the laser radar sen- sor.

235

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

this code appears, clean

If “E1” appears on the display, the sys- tem cannot easily measure the vehicle−to− vehicle distance because of a dirty laser radar sensor glass while the dynamic la- ser cruise control is on. If the sensor glass with a soft cloth and try setting the preset speed again. If the dirt is removed without cleaning, the system will automati- cally enter the ready mode. If the system does not enter the ready mode even after cleaning or the code re- mains on the display, the system might be malfunctioning. Although there is no prob- lem to continue driving, please contact your Toyota dealer.

CAUTION

Always keep the sensor glass and never allow to be covered with icicle or any substance, so it can de- tect the vehicle in front.

it

If “E2” appears on the display, the sys- tem cannot easily measure the vehicle−to− vehicle distance because of the following conditions: D The wipers are operating at high or low

speeds

D Direct sunlight from the front D It is difficult to make a measurement because of bad weather (such as rainy, foggy, or snowy weather) the

In laser cruise control switches to the ready mode: stopped or are D The wipers

following cases, dynamic

are

switched to intermittent operation. D No direct sunlight from the front In the above conditions, push the lever up in the “+ RES” direction and release it. Dynamic laser cruise control will be re- stored. If the setting operation cannot be performed or if the warning code still ap- pears even after the weather clears, the system might have malfunctioned. Al- though there is no problem to continue driving, contact your Toyota dealer.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

DISTANCE

VEHICLE−TO−VEHICLE CONTROL MODE FAILURE WARNING If there is trouble somewhere in the dy- namic laser cruise control while the ve- hicle−to−vehicle distance control mode is on, the master warning light comes on and the alarm sounds, and one of the warning codes “E1”, “E2” or “E3” will ap- pear on the display. Dynamic laser cruise control is automatically cancelled. If the “CRUISE” indicator light in the instrument cluster also flashes.

“E3” appears on

the display,

236

If “E3” appears on the display, a system malfunction has been detected. If this code appears, stop your vehicle in a safe place, turn the engine switch off, and then restart it to reset the system. If the setting still cannot be made or the same code appears again, the system might have malfunctioned. Although there is no problem to continue driving, contact your Toyota dealer.

08 SIENNA_U (L/O 0801)

—Conventional (fixed speed) cruise control mode The conventional cruise control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Cruising speed can be set to any speed above 45 km/h (28 mph). Within the limits of the engine’s capabili- ties, cruising speed can be maintained up or down grades. However, changes in ve- hicle speed may occur on steeper grades.

CAUTION

D In the conventional cruise control mode, the approach warning does not activate and no alarm will sound even if you are too close to the vehicle ahead, as neither the presence of the vehicle ahead nor the vehicle−to−vehicle distance is detected. Pay special attention to the distance between your vehicle and the vehicle ahead. Always con- firm the setting in the display.

D Do not use the conventional mode in the following conditions, or seri- ous injury or death could result: To help maintain maximum control of your vehicle, do not use conven- tional cruise control mode when us- ing dynamic laser cruise control while driving in heavy or varying traffic, or on slippery (rainy, icy or snow−covered) or winding roads. Be careful about vehicle speed as it may increase when driving down- hill with the conventional cruise control mode selected.

237

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

However, once the vehicle−to−vehicle dis- tance control mode activates and is used, it cannot be changed to the conventional cruise control mode using the above op- eration. To change the mode, press the “ON−OFF” button to turn the system off and then press it again to turn it on. Next push the lever in the “MODE” direction for longer than about 1 second. To change to the vehicle−to−vehicle dis- tance control mode from the conventional cruise control mode, push the lever in the “MODE” direction for longer than about 1
second.

CAUTION

the To avoid accidentally engaging cruise control, turn the system off when it is not in use. Make sure the “CRUISE” indicator light is off.

SETTING THE CRUISING SPEED The transmission must be in “D” or “4” before you set the cruising speed. Bring your vehicle to the desired speed, push the lever down in the “− SET” direc- tion and release it. This sets the vehicle at that speed and the display shows the preset speed. You can now take your foot off the accelerator pedal. If you need to accelerate—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you release the accelerator pedal, the vehicle will return to the speed set prior to acceleration.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

turn

“READY”

“CRUISE” and

TURNING THE SYSTEM ON AND OFF To the conventional cruise control mode on, turn the “ON−OFF” button on. The indicator lights on the instrument panel will come on. Push the lever in the “MODE” direc- tion for longer than 1 second to change to conventional cruise control mode. The indicator on the instrument panel is as shown. You can now set the cruising speed. Pressing “ON−OFF” button again turns the system off. When the system is turned off, cruising speed must be reset when the convention- al cruise control mode is turned on again.

the

238

THE

indicates

the display

CONVENTIONAL

the display, see

You cannot set a desired speed if the master warning light comes on, the alarm sounds and the warning code “E3”. If this code appears “CONVENTIONAL on CRUISE CONTROL MODE FAILURE WARNING” on page 240. CANCELLING CRUISE CONTROL MODE The conventional cruise control mode may be temporarily cancelled by the driver or by the system itself under certain circum- stances. Temporary cancellation allows the set cruising speed to remain in memory. The conventional cruise control mode can be temporarily cancelled by doing the fol- lowing: D Pulling the lever in the “CANCEL” di-

rection and releasing it

D Depressing the brake pedal Under certain circumstances, the conven- tional cruise control mode is temporarily cancelled: D When vehicle speed

falls below 40

km/h (25 mph)

D When vehicle stability control is acti-

vated

08 SIENNA_U (L/O 0801)

When vehicle speed drops 16 km/h (10
mph) below the set speed, the convention- al cruise control mode is cancelled and the set speed is erased from memory. The “CRUISE” indicator light remains on to indicate that the system is still in op- eration. To turn the system off, press the “ON− OFF” button. Make sure the “CRUISE” in- dicator light is off. If the conventional cruise control mode automatically cancels out other than for the above cases, have your vehicle checked by your Toyota dealer at the ear- liest opportunity. RESUMING CRUISE CONTROL MODE If the conventional cruise control mode is temporarily cancelled, the cruising speed can be resumed by pushing the lever up in the “+ RES” direction. Vehicle speed must be above 40 km/h (25
mph).

CONVENTIONAL

THE

RESETTING TO A FASTER SPEED Push the lever up in the “+ RES” direction and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be increased 1.6 km/h (1 mph) each time by pushing the lever up in the “+ RES” direction quickly within 0.6 seconds. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction.

239

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

RESETTING TO A SLOWER SPEED Push the lever down in the “− SET” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be lowered 1.6 km/h (1 mph) each time by pushing the lever down in the “− SET” direction quickly within 0.6 seconds. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction. Even if you downshift from “D” to “4” in the conventional cruise control mode, en- gine braking will not be enabled because this mode is not cancelled. To decrease the vehicle’s speed, reset to a slower speed with the cruise control lever or de- press the brake pedal, cruise control is cancelled.

the brake pedal.

If you use

is

in

there

trouble

CRUISE

CONTROL

CONVENTIONAL MODE FAILURE WARNING the conventional If cruise control mode, the “CRUISE” indica- tor light in the instrument cluster flashes, the master warning light comes on and the alarm sounds, the warning code “E3” will appear on the display. If a system malfunction is detected when the conventional cruise control mode is in the ready mode or operating, the master warning light comes on, an alarm sounds and the above code appears. If this code appears, press the “ON−OFF” button to turn the system off and then push it again to turn it on. If the setting still cannot be made or the same code appears again, the system might have malfunctioned. Although there is no prob- lem to continue driving, please contact your Toyota dealer.

240

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

SECTION 1− 8

OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference Using your audio system AUX adapter Audio remote controls Rear seat entertainment system Audio/video system operating hints Hands−free phone system

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

242
242
264
265
268
309
316

For vehicle equipped with Navigation system, please refer to the separate “Navigation System Owner’s Manual”.

241

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Reference

Type 1: AM·FM radio/compact disc player (with compact disc changer controller)

Type 2−1: AM·FM radio/compact disc play- er with changer (with XMr Satellite Radio∗ controller) 242

Type 2−2: AM·FM radio/compact disc play- er with changer (with XMr Satellite Radio∗ controller) ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

radio

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the engine switch is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. “AM·SAT”∗, Push “DISC·AUX” or “LOAD” turn on function without pushing “PWR·VOL”. You can turn on each player by inserting a compact disc. You can turn off each player by ejecting the compact disc. If the audio system was previously off, then the entire audio sys- tem will be turned off when you eject the compact disc. If another function was pre- viously playing, it will come on again. ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

“FM2”, that

“FM1”,

“AM”,

radio

to

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

“AM”,

“FM1”,

“AM·SAT”∗,

SWITCHING BETWEEN FUNCTIONS “FM2”, Push “DISC·AUX” or “LOAD” if the system is already on but you want to switch from one function to another. ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

radio

to

LISTENING TO THE XMr SATELLITE RADIO BROADCAST∗ (type 2−1 and 2−2) To listen to a satellite radio broadcast in your vehicle, an additional genuine Toyota satellite receiver and antenna (or equiva- lents) must be purchased and installed. A the XMr Satellite Radio subscription service is also necessary. How to subscribe to an XMr Satellite Radio An XMr Satellite Radio is a tuner de- signed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 contiguous states.

How to subscribe: You must enter into a separate service agreement with the XMr Satellite Radio in order to receive satellite broadcast pro- gramming in the vehicle. Additional activa- tion and service subscription fees apply that are not included in the purchase price of the vehicle and optional digital satellite tuner. For complete information on sub- scription rates and terms, or to subscribe to the XMr Satellite Radio, visit XMr on the web at www.xmradio.com or call an XMr’s Listener Care at (800) 967−2346. The XMr Satellite Radio is solely respon- sible for the quality, availability and con- tent of the satellite radio services pro- vided, which are subject to the terms and conditions of the XMr Satellite Radio cus- tomer service agreement. Customers should have ID ready; the radio ID can be found by tun- ing to “channel 000” on the radio. For details, see “Displaying the radio ID” be- low. All fees and programming are the respon- sibility of the XMr Satellite Radio and are subject to change.

radio

their

the services offered by

Satellite tuner technology notice: Toyota’s satellite radio tuners are awarded Type Approval Certificates from XMr Sat- ellite Radio Inc. as proof of compatibility the XMr with Satellite Radio. Displaying the radio ID Each XMr tuner is identified with a unique radio ID. You will need the radio ID when activating XMr service or when reporting a problem. If you select the “TUNE·FILE” knob, the ID code of 8 al- phanumeric characters appears. If you se- lect another channel, display of the ID code is canceled. The channel (000) alter- nates the display between the radio ID and the specific radio ID code. ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

“CH 000” using

radio

the

243

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange (type 2−2) and bass levels. In fact, different kinds of music and vocal programs usually sound better with different mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another. YOUR RADIO ANTENNA Your vehicle has the mast type antenna or on−glass antenna printed on the inside of the rear quarter window. Mast type antenna—To remove an anten- na, carefully turn it counterclockwise.

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. SRS

(type 1 and 2−1)

license

The audio systems utilize SRS FOCUSr and SRS TruBassr audio enhancement technologies, under from SRS Labs, Inc., in all modes except AM radio mode. FOCUS, TruBass, SRS and are trademarks of SRS Labs, Inc. FOCUS and TruBass incorporated under Labs, Inc.

technologies are from SRS

rsymbols

license

244

NOTICE

z Mast type antenna:

it

To prevent damage to the antenna, make sure is removed before driving your Toyota through an au- tomatic car wash. z On−glass antenna:

Putting a film (especially a conduc- tive or metallic film) on the rear window will noticeably reduce the sensitivity of the radio.

YOUR COMPACT DISC PLAYER (type 1) When you insert a disc, gently push it in with the label side up. The player will play from track 1 through to the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

YOUR COMPACT DISC PLAYER WITH CHANGER (type 2−1 and 2−2) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. This compact disc play- er can store up to six discs. The player will play from track 1 through to the end of the disc. Then it will play from track 1 of the next disc.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

NOTICE

z Do not stack up two discs for in- sertion, or it will cause damage to the compact disc changer. Insert only one compact disc into slot at a time.

z Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a com- pact disc into the slot.

CAUTION

Laser products D Do not take this unit apart or at- tempt to make any changes your- self. This is an intricate unit that uses a laser pickup to retrieve in- formation from the surface of com- pact discs. The laser is carefully shielded so that its rays remain in- side the cabinet. Therefore, never try to disassemble the player or al- ter any of its parts since you may be exposed to laser rays and dan- gerous voltages.

D This product utilizes a laser. Use of controls or adjustments or per- formance of procedures other than those specified herein may result in hazardous radiation exposure.

245

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

—Controls and features "Type 1

Details of specific buttons, controls and features are described in the alphabetical list that follows.

246

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

the

the

you

time

tone and balance,

AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7.

turn

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. (See “TUNE·FILE” or “SEEK/TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To recall a preset station: Push the button for the station you want. The button num- ber and station frequency will appear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM”, “FM1” or “FM2” button.)

(Eject button)

the compact disc eject button

Push eject a compact disc.

to

(Reverse/Fast−forward button)

Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing.

ASL: The Automatic Sound Levelizer can be turned on by turning the knob. In addi- tion, turning the knob allows you to select from LOW, MID, and HIGH volume and tone settings. The ASL system automati- cally adjusts volume and tone in accor- dance with ambient noise levels. This helps ensure an optimal listening experi- ence even when road, wind or other ambi- ent noise levels rise. RSE: Vehicles with a rear seat entertain- ment system—The system can be locked. For details, see page 280 in this Section.

247

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

to play a

the “DISC·AUX” button

DISC·AUX (Compact disc) Push compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Vehicles with rear seat entertainment sys- tem— The “DISC·AUX” button may also be used to operate a DVD player when a disc is loaded in the DVD player. Pressing the “DISC·AUX” button changes between the CD player and DVD player. When the DVD player is in operation, “AUX” appears on the display. Vehicles with AUX adapter— To switch between CD, DVD, and AUX (external the “DISC·AUX” button. The AUX mode is only available when AUX adapter is connected to the system. When the AUX adapter is in use, “AUX” will appear on the display.

device) modes,

press

248

08 SIENNA_U (L/O 0801)

inserted

incorrectly

Error messages If the player malfunctions, your audio sys- tem will display following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If “NO MUSIC” appears on the display, it indicates that a disc with no MP3/WMA data has been inserted. Remove the disc from the player and insert an MP3/WMA data disc. If the malfunction still exists, take your vehicle to your Toyota dealer.

Ɲ DISC Ɯ With compact disc changer only— Use these buttons to select the disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen appears on the display. FM1 FM2
Push the “FM1” or “FM2” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM sta- tions, two for each of the preset button. MP3/FOLDER (Folder up/down) To skip up or down to a different folder: Push either side of the “MP3/FOLDER” several times until the number of the fold- er you want to listen to appears on the display. To jump to the first folder: Push and hold the “Ɲ” side of the button until you hear a beep. When playing a disc featuring both audio data (CD−DA) and MP3/WMA files, audio data (CD−DA) is played.

file in the current

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

in a

the files

MP3/WMA player There are two random playback features— you can either listen to all of the files on the compact discs in random order. You can also listen to the files in a single folder in random order. To randomly play folder: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display. To randomly play all of the files on the compact disc: Push and hold “RAND” (preset button 1) ” will until you hear a beep. “ appear on the display and the player will play all of the files on the disc in random order. To turn off the random playback feature, push this button again.

in random order, or

PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) Compact disc player There are two random features—you can either listen to the tracks on one compact to disc listen the tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will until you hear a beep. “ appear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

feature, push

random

the

track

RPT (Repeat) Compact disc player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

249

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

file

the

MP3/WMA player There are two repeat features—you can repeat a signal file or an entire folder. Repeating a file: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the file ends, it will repeat automatically. This process will be continued until you push the button again to turn off the re- peat feature. Repeating a folder: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all of the files in the folder. When the last file in the folder ends, the folder will re- peat from the beginning. To turn off the repeat feature, push this button again.

08 SIENNA_U (L/O 0801)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up or down the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up or down the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan up or down all the tracks on the disc you are listening to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. The discs in the compact disc changer can be scanned up only. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push and hold the “SCAN” button until you hear a beep. “ SCAN” will appear on the display and the player will scan up the first track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scanning.

250

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

to. To select a

MP3/WMA player There are two scan features—you can ei- ther scan the files in a folder on a specif- ic disc or scan the first file of all the folder. Scanning the files on a folder: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the files in the folder you are listening file, push the “SCAN” again. After all the tracks on the disc have been scanned in one pass, nor- mal play resumes. Scanning the first file of all the folders: “SCAN” until you hear a beep. Push ” will appear on the display and “ the player will scan the first file of the next folder. To select a folder, push the “SCAN” again. After all the folders have been scanned in one pass, normal play resumes.

of

or

“Ɲ”

“Ɯ”

side

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release the “SEEK/TRACK” button. Do this again to find the station after that. Compact disc player Use this button to skip up or down to a different track. Push the “SEEK/TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the beginning of track, quickly push the button one time. Vehicles with rear seat entertainment sys- tem— While the DVD player is in operation, the chapter or track can be changed by push- ing the “SEEK/TRACK” button.

the down side of

the current

side of

“Ɯ” or

side

“Ɲ”

“Ɲ”

“Ɯ”

the

or

of

to return to

the beginning of

MP3/WMA player To file up or down to a different file: the “SEEK/TRACK” Push either side of several times until the file you want to listen to appears on the display. If you want the current file, push the “Ɲ” side of the but- ton one time, quickly. To fast forward or reverse the disc: If you want to fast forward or reverse the disc, push and hold it until you hear a beep. When you release the button, the player will resume playing. Vehicles with rear seat entertainment sys- tem— While the DVD player is in operation, the chapter or track can be changed by push- ing the “SEEK/TRACK” button. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

side of

“Ɯ” or

“Ɲ”

the

251

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

TEXT Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear.

then back

track

title,

to

to

08 SIENNA_U (L/O 0801)

file

the

from

this button

in the order

“TEXT” button while

MP3/WMA player This button is used to change the display for the MP3/WMA file that contains text data. To change the display, quickly push and release the MP3/WMA is playing. The display changes the elapsed time to folder name to file name to album title to track title to artist name, then back to the elapsed time. If is pushed while an MP3/WMA file that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire text data is not displayed, push and hold it until you hear a beep. The rest of the text data will appear. TUNE·FILE (Tuning and File up/down) Radio Turn the “TUNE·FILE” knob clockwise to the knob step up counterclockwise fre- quency. MP3/WMA player Turn the knob clockwise to file up. Turn the knob counterclockwise to file down.

frequency. Turn

to step down

the

the

252

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

"Type 2−1

Details of specific buttons, controls and features are described in the alphabetical list that follows.

253

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

"Type 2−2

254

08 SIENNA_U (L/O 0801)

Details of specific buttons, controls and features are described in the alphabetical list that follows.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. (See “TUNE·FILE” or “SEEK/TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset but- ton number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM·SAT”, “FM1” or “FM2” button.) XMr Satellite Radio∗— These buttons are used tune in radio channels. To preset a channel to a button: Tune in the desired channel. (See “TUNE·FILE” or “SEEK/TRACK”.) Push and hold down the button until you hear a beep—this will set the channel to the button. The preset but- ton number will appear on the display.

to preset and

08 SIENNA_U (L/O 0801)

To recall a preset channel: Push the but- ton for the channel you want. The preset button number and channel number will appear on the display. This radio can store three XMr channels for each button. (The display will show “SAT1”, “SAT2” or “SAT3” when you push “AM·SAT” button.) ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

radio

(Eject button)

This button is used to eject one or all compact discs. To eject the current compact disc, push and release the compact disc eject button. To eject a specific disc, push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to eject is displayed. Push and release the eject but- ton. To eject all discs at a time, press and hold the eject button until you hear a beep. The last compact disc played before pushing the button will be ejected first. If the ejected disc is not removed for a long time, the eject function will be canceled.

(Reverse/Fast−forward button)

Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM·SAT (AM band and XMr Satellite Radio∗) Push the “AM·SAT” button to turn on the radio and select the AM or XMr band. “AM”, “SAT1”, “SAT2” or “SAT3” will ap- pear on the display. Error messages If tuner malfunctions, your audio system will display the follow- ing error messages. “ANTENNA”: D The XMr antenna

is not connected. Check whether the XMr antenna cable is attached securely.

the satellite radio

D A short−circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer.

255

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

“UPDATING”: D You have not subscribed to the XMr Satellite Radio. The radio is being up- dated with the latest encryption code. Contact for subscription information. When a con- tact is canceled, you can choose the “CH000” and all free−to−air channels.

the XMr Satellite Radio

D The premium channel you selected is not authorized. Wait for about 2 sec- onds until the radio returns to the pre- vious channel or “CH001”. If it does not change automatically, select anoth- er channel. If you want to listen to the the XMr premium channel, contact Satellite Radio.

is

“NO SIGNAL”: The XMr signal too weak at the current location. Wait until your vehicle reaches a location with a stronger signal. “LOADING”: The unit is acquiring audio or program information. Wait until the unit has received the information. “OFF AIR”: The channel you selected is not broadcasting any programming. Select another channel.

256

to

the radio returns

“− − −”: The channel you selected is no longer available. Wait for about 2 seconds until the previous channel or “CH001”. If it does not change automatically, select another channel. The XMr Listener Care Center is also available on the phone, please call (800) 967−2346 during the following hours: Monday—Saturday: 6 a.m.—2 a.m. East- ern Time Sunday: 8 a.m.—8 p.m. Eastern Time ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

radio

the

the

you

turn

time

tone and balance,

AUDIO CONTROL (Tone and sound bal- ance adjustment function) “AUDIO Each push CONTROL” knob, the mode changes. To adjust the knob. Type 2−1— BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7.

BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. ASL: The Automatic Sound Levelizer can be turned on by turning the knob. The ASL system automatically adjusts volume and tone in accordance with ambient noise levels. This helps ensure an optimal lis- tening experience even when road, wind or other ambient noise levels rise. RSE: Vehicles with a rear seat entertain- ment system—The system can be locked. For details, see page 280 in this Section. Type 2−2— BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. MID: Adjusts mid−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

ON”

“SURROUND

SURROUND: Turn on or off the surround or function. “SURROUND OFF” will appear on the display. ASL: The Automatic Sound Levelizer can be turned on by turning the knob. In addi- tion, turning the knob allows you to select from LOW, MID, and HIGH volume and tone settings. The ASL system automati- cally adjusts volume and tone in accor- dance with ambient noise levels. This helps ensure an optimal listening experi- ence even when road, wind or other ambi- ent noise levels rise. RSE: Vehicles with a rear seat entertain- ment system—The system can be locked. For details, see page 280 in this Section.

to play a

the “DISC·AUX” button

DISC·AUX (Compact disc) Push compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Vehicles with rear seat entertainment sys- tem— The “DISC·AUX” button may also be used to operate a DVD player when a disc is loaded in the DVD player. Pressing the “DISC·AUX” button changes between the CD player and DVD player. When the DVD player is in operation, “AUX” appears on the display. Vehicles with AUX adapter— To switch between CD, DVD, and AUX (external the “DISC·AUX” button. The AUX mode is only available when AUX adapter is connected to the system. When the AUX adapter is in use, “AUX” will appear on the display.

device) modes,

press

inserted

incorrectly

Error messages If the player malfunctions, your audio sys- tem will display following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If “NO MUSIC” appears on the display, it indicates that a disc with no MP3/WMA data has been inserted. Remove the disc from the player and insert an MP3/WMA data disc. If the malfunction still exists, take your vehicle to your Toyota dealer.

257

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

To load multiple compact discs, push and hold the button (until you hear a beep when the audio system is on). When the indicators on both sides of the slot turn green, insert the first compact disc. After the disc is loaded, the shutter of the slot will close. After a few seconds, the shut- ter will automatically open again and the indicators will turn green so the next disc can be inserted. The same process can be applied the discs. If the player is full of discs, “DISC FULL” will appear on the display. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume.

the rest of

loading

for

Ɲ DISC Ɯ Use these buttons to select a disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen to appears on the display. FM1 FM2
Push the “FM1” or “FM2” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM sta- tions, two for each of the preset button. LOAD This button is used to load the compact discs the compact disc player. This player can store up to six discs. To load one compact disc only, quickly push and release the button, then insert a compact disc. After the disc is loaded, the shutter of the slot will close. If no compact disc is inserted, the shutter will close after 15 seconds.

in

258

in random order, or

RAND (Random) Compact disc player There are two random features—you can either listen to the tracks on one compact to disc listen the tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will until you hear a beep. “ appear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

feature, push

random

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

in a

the files

MP3/WMA player There are two random playback features— you can either listen to all of the files on the compact discs in random order. You can also listen to the files in a single folder in random order. To randomly play folder: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display. To randomly play all of the files on the compact disc: Push and hold “RAND” (preset button 1) ” will until you hear a beep. “ appear on the display and the player will play all of the files on the disc in random order. To turn off the random playback feature, push this button again.

the

track

RPT (Repeat) Compact disc player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

file

the

MP3/WMA player There are two repeat features—you can repeat a signal file or an entire folder. Repeating a file: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the file ends, it will repeat automatically. This process will be continued until you push the button again to turn off the re- peat feature. Repeating a folder: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all of the files in the folder. When the last file in the folder ends, the folder will re- peat from the beginning. To turn off the repeat feature, push this button again.

259

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

the currently selected channel

To scan the preset channels: Push and hold the “SCAN” button until you hear a beep. “SCAN” appears on the display. The radio will tune in the next preset channel up the band, stay there for 5 seconds, and then move to the next preset channel. To stop scanning, push this button again. To scan category: Quickly push and release the “SCAN” but- ton. “SCAN” appears on the display. The radio will the same channel category up the band, stay there for 5 seconds, and then scan again. To stop scanning, push this button again. ∗: Use of satellite requires XMr tuner and service. Contact your Toyota dealer for details.

the next channel

radio

find

in

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up or down the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up or down the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again. XMr Satellite Radio∗— You can either scan the currently selected channel category or scan only the preset channels for that band.

260

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan up or down all the tracks on the disc you are listening to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. The discs in the compact disc changer of separate unit can be scanned up only. Scanning the first tracks of all the discs in the magazine: Push and hold the “SCAN” button until you hear a beep. “ SCAN” will appear on the display and the player will scan up or down the first track of the next disc. To stop scanning, push this button again. If the auto changer has scanned all the discs, it will stop scanning. The discs in the compact disc changer of separate unit can be scanned up only.

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

to. To select a

MP3/WMA player There are two scan features—you can ei- ther scan the files in a folder on a specif- ic disc or scan the first file of all the folder. Scanning the files on a folder: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the files in the folder you are listening file, push the “SCAN” again. After all the tracks on the disc have been scanned in one pass, nor- mal play resumes. Scanning the first file of all the folders: “SCAN” until you hear a beep. Push ” will appear on the display and “ the player will scan the first file of the next folder. To select a folder, push the “SCAN” again. After all the folders have been scanned in one pass, normal play resumes.

or

“Ɲ”

“Ɯ”

side

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release the “SEEK/TRACK” button. Do this again to find the station after that. XMr Satellite Radio∗— To select the next channel within the cur- rent channel category, push the “Ɯ” or “Ɲ” side of the “SEEK/TRACK” button. Repeat until a desired channel is found. ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

radio

of

of

or

“Ɲ”

“Ɯ”

side

Compact disc player Use this button to skip up or down to a different track. Push the “SEEK/TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the beginning of track, quickly push the button one time. Vehicles with rear seat entertainment sys- tem— While the DVD player is in operation, the chapter or track can be changed by push- ing the “SEEK/TRACK” button.

the down side of

the current

side of

“Ɯ” or

“Ɲ”

the

261

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

to return to

the beginning of

MP3/WMA player To file up or down to a different file: the “SEEK/TRACK” Push either side of several times until the file you want to listen to appears on the display. If you want the current file, push the “Ɲ” side of the but- ton one time, quickly. To fast forward or reverse the disc: If you want to fast forward or reverse the disc, push and hold it until you hear a beep. When you release the button, the player will resume playing. Vehicles with rear seat entertainment sys- tem— While the DVD player is in operation, the chapter or track can be changed by push- ing the “SEEK/TRACK” button. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

side of

“Ɯ” or

“Ɲ”

the

the display

that affects

TEXT XMr Satellite Radio∗1— When you push the “TEXT” button, the display changes as follows: CH NAME → TITLE (SONG/PROGRAM TITLE) → NAME (ARTIST NAME/FEA- TURE) → CH NUMBER → CH NAME Up to 10 alphanumeric characters can be displayed. (Some information will not be fully displayed.) The message display will be canceled if any button is pushed. If there is no song/program title or artist name/feature associated with the channel at that time, “− − − − −” will appear on the display. This XMr tuner supports “Audio Services” (Music and Talk) of only XMr Satellite Radio and “Text Information”∗2 linked to the respective audio services. ∗1: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details. Information

includes, Channel Name, (Artist) Name, (Song) Title and Category Name.

∗2: Text

radio

to

Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear.

then back

track

title,

to

262

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

file

the

in the order

“TEXT” button while

MP3/WMA player This button is used to change the display for the MP3/WMA file that contains text data. To change the display, quickly push and release the MP3/WMA is playing. The display changes the elapsed time to folder name to file name to album title to track title to artist name, then back to the elapsed time. If is pushed while an MP3/WMA file that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire text data is not displayed, push and hold it until you hear a beep. The rest of the text data will appear.

this button

from

08 SIENNA_U (L/O 0801)

TYPE/FOLDER (Type/Folder up/down) Radio XMr Satellite Radio∗— When you push the “Ɲ” or “Ɯ” side of the “TYPE/FOLDER” button while receiving a XMr channel, the current channel cate- gory appears on the display. When the channel category appears, push either the “TYPE/FOLDER” button to switch to the next or previous category. ∗: Use of satellite radio

requires XMr tuner and service. Contact your Toyota dealer for details.

side

“Ɲ”

“Ɯ”

or

of

MP3/WMA player To skip up or down to a different folder: Push either side of the “TYPE/FOLDER” several times until the number of the fold- er you want to listen to appears on the display. To jump to the first folder: Push and hold the “Ɲ” side of the button until you hear a beep. When playing a disc featuring both audio data (CD−DA) and MP3/WMA files, audio data (CD−DA) is played.

file in the current

the

to step down

frequency. Turn

TUNE·FILE (Tuning and File up/down) Radio Turn the “TUNE·FILE” knob clockwise to the knob step up counterclockwise fre- quency. XMr Satellite Radio∗— Turn the “TUNE·FILE” knob clockwise to step up the channel. Turn the knob coun- terclockwise to step down the channel. ∗: Use of satellite

requires XMr tuner and service. Contact your Toyota dealer for details.

radio

the

MP3/WMA player Turn the knob clockwise to file up. Turn the knob counterclockwise to file down.

263

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

08 SIENNA_U (L/O 0801)

AUX adapter

If you install an audio system other than a genuine audio system, you will not be able to use the AUX adapter.

inserting a mini plug into

By the AUX adapter, you can listen to music from a portable audio device through the vehicle’s speaker system. To use the AUX adapter, switch to the AUX mode (external device mode) by pressing the “DISC·AUX” button. When the AUX adapter is in use, “AUX” will appear on the display. To adjust the volume, turn the “PWR·VOL” knob. When using a portable audio device con- nected to the power outlet or cigarette lighter, noise may occur during playback. If this happens, use the power source of the portable audio device.

264

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

Audio remote controls (steering switches)

08 SIENNA_U (L/O 0801)

Some parts of the audio system can be adjusted using the switches on the steer- ing wheel. Details of the specific switches, controls, and features are described below. 1. Volume control switch 2. “ƜƝ” switch 3. “MODE” switch

265

2008 SIENNA from Aug. ’08 Prod. (OM45455U)

to

increase while

1. Volume control switch Push “+” to increase the volume. The vol- ume continues the switch is being pushed. Push “−” the volume. The to decrease volume continues to decrease while the