01 SIENNA_U (L/O0008)
Foreword
Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build. This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the follow- ing pages carefully. When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality mainte- nance and any other assistance you may require. Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also. All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of continual product improvement, we reserve the right to make changes at any time without notice. Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle.
© 2000 TOYOTA MOTOR CORPORATION All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Important information about this manual
Safety and vehicle damage warnings
Safety symbol
Throughout this manual, you will see safety and vehicle dam- age warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows:
CAUTION
This is a warning against something which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk to yourself and other people.
NOTICE
This is a warning against something which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.
the safety symbol When you see shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.
ii
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Important information about your Toyota
New vehicle warranty
Your new vehicle limited warranties:
is covered by
the
following Toyota
D New vehicle warranty D Emission control systems warranty D Others further
information, please refer
Information Booklet” or
For Warranty Supplement”.
to the “Owner’s “Owner’s Manual
Your responsibility for maintenance
It is the owner’s responsibility to make sure that the specified maintenance is performed. Section 6 gives de- tails of these maintenance requirements. Also included in Section 6 is general maintenance. For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
Accessories, spare parts and modification of your Toyota
A wide variety of non−genuine spare parts and accesso- ries for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their perfor- mance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durabili- ty, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.
iii
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Spark ignition system of
your Toyota
The spark ignition system in your Toyota meets all re- quirements of the Canadian Interference−Causing Equip- ment Standard.
Installation of a mobile two−way radio system
Scrapping of your Toyota
The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by the quali- fied service shop or by your Toyota dealer before you dispose of your vehicle.
fuel
injection system/sequential multiport
As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as multiport fuel injection system, cruise control system, anti−lock brake system, traction control system, vehicle skid control sys- tem, SRS airbag system and seat belt pretensioner sys- tem, be sure to check with your Toyota dealer for pre- cautionary measures or special regarding installation.
instructions
iv
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
SECTION 1− 1
OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview Instrument cluster overview Indicator symbols on the instrument panel
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Instrument panel overview
1. Side defroster outlets 2. Side vents 3. Instrument cluster 4. Automatic transmission selector lever 5. Center vents 6. Garage door opener, garage door
opener box or auxiliary box
7. Electric moon roof switch, front
personal light or front interior light switch
8. Front personal lights or front interior
light
9. Power door lock switches 10. Power window switches 11. Glove box 12. Auxiliary boxes 13. Tilt steering lock release lever 14. Hood lock release lever 15. Parking brake pedal 16. Window lock switch
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches 3. Clock and front passenger’s seat belt
reminder light
4. Emergency flasher switch 5. Front air conditioning controls 6. Rear fan speed selector or rear fan
position selector
7. Rear window and outside rear view
mirror defoggers switch
8. Car audio 9. Seat heater switches 10. Ashtray 11. Power sliding door switches 12. Power outlet 13. Cigarette lighter 14. Power rear quarter window switch 15. Ignition switch 16. Cruise control switch 17. Audio remote control buttons 18. Power sliding door off switch
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
19. Tire pressure warning system reset switch or traction control system off switch
20. Theft deterrent system/Engine
immobiliser system indicator light
21. Power rear view mirror control switch 22. Instrument panel light control dial
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Instrument cluster overview "With tachometer
1. Engine coolant temperature gauge 2. Tachometer 3. Service reminder indicators and
indicator lights
4. Speedometer 5. Fuel gauge 6. Trip meter reset knob
7. Odometer and two trip meters
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
"Without tachometer
1. Engine coolant temperature gauge 2. Service reminder indicators and
indicator lights
3. Speedometer
4. Odometer and two trip meters 5. Fuel gauge 6. Trip meter reset knob
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Indicator symbols on the instrument panel
or
Brake system warning light∗1
or
Anti−lock brake system warning light∗1
Driver’s seat belt reminder light∗1
Open door warning light∗1
Front passenger’s seat belt reminder light∗1
Open power sliding door warning light∗1
Discharge warning light∗1
SRS warning light∗1
or
Malfunction indicator lamp∗1
Vehicle skid control system warning light∗1
Low windshield washer fluid level warning
light∗1
Low fuel level warning light∗1
Low tire pressure warning light∗1
Low oil pressure warning light∗1
Traction control system off indicator/warning
light∗1
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Turn signal indicator lights
Headlight high beam indicator light
Overdrive−off indicator light
Cruise control indicator light∗2
Automatic transmission indicator lights
Slip indicator light
∗1: For details, see “Service reminder indicators and warning
buzzers” in Section 1−5.
∗2: If this light flashes, see “Cruise control” in Section 1−6.
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
SECTION 1− 2
OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors
Keys
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
Engine immobiliser system
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Front doors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Sliding door
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Power sliding door
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
Wireless remote control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Power windows
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Power rear quarter windows
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
Center side windows and manual rear quarter windows
. . . . . . . . . .
32
Back door
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Hood
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
Theft deterrent system
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
Fuel tank cap
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
Electric moon roof
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Keys (without engine immobiliser system)
Keys (with engine immobiliser system)
Your vehicle is supplied with two kinds of keys. 1. Master key—This key works in every
lock.
2. Sub key—This key will not work in the
glove box.
To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant. Since the doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.
KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend you to write down the key number and keep it in safe place.
Your vehicle is supplied with two kinds of keys. 1. Master key (black)—This key works in lock. Your Toyota dealer will every need it to make you a new key with built−in transponder chip.
2. Sub key (gray)—This key will not work
in the glove box.
A transponder chip for engine immobiliser system has been filled in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.
10
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant. Since the side door can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.
NOTICE
the
When using a key containing a trans- ponder chip, observe following precautions: z When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.
z When starting the engine, do not use the key with other transponder keys around (including keys of oth- er vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after taking off other transponder keys (includ- ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.
2001 MY SIENNA (OM45406U)
11
01 SIENNA_U (L/O0008)
z Do not cover the key grip with any material that cuts off electromagnet- ic waves.
z Do not knock the key hard against
other objects.
z Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.
z Do not put the key
in water or
wash it in an ultrasonic washer.
z Do not bend the key grip.
z Do not use the key with electromag-
netic materials.
KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend you to write down the key number and keep it in safe place.
12
2001 MY SIENNA (OM45406U)
Engine immobiliser system
01 SIENNA_U (L/O0008)
Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off. For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you. If you make your own duplicate key, you will not be able to cancel the sys- tem or start the engine.
immobiliser system
The engine is a theft prevention system. When you in- sert the key in the ignition switch, the transponder chip the key’s head transmits an electronic code to the ve- hicle. The engine will start, only when the electronic code in the chip corre- sponds to the registered ID code for the vehicle.
in
indicator
light will start
The system is automatically set when the key is removed from the ignition switch. The flashing to show the system is set. If either of the following indicator condi- tions occurs, contact your Toyota dealer. D The light stays on except when the theft deterrent system is set- ting or activating. (See “Theft deterrent system”.)
indicator
D The indicator light does not start flash- ing when the key is removed from the ignition switch.
D The indicator light flashes unsteady.
2001 MY SIENNA (OM45406U)
13
01 SIENNA_U (L/O0008)
For vehicles sold in U.S.A.
For vehicles sold in Canada
Front doors
This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.
interference,
including
FCC ID: MOZ RI−4BTY MADE IN JAPAN This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.
CAUTION
Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
14
2001 MY SIENNA (OM45406U)
LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. Vehicles with power door lock system—All the doors lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice in succession will unlock all the doors simultaneously.
01 SIENNA_U (L/O0008)
LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch on the front side. To unlock: Push the switch on the rear side. All the doors lock or unlock simultaneous- ly.
CAUTION
Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of locking the doors helps seat belts, prevent the driver and passengers from being thrown out from the ve- hicle during an accident. It also helps prevent the doors from being opened unintentionally.
Driver’s side
LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. Closing the front door with the lock knob in the lock position will also lock the front door. Be careful not to lock your keys in the vehicle. Vehicles with power door sys- tem—The door cannot be locked if you leave the key in the ignition switch.
lock
Passenger’s side
2001 MY SIENNA (OM45406U)
15
01 SIENNA_U (L/O0008)
Sliding door
CLOSING FROM OUTSIDE To close the fully−opened sliding door, pull the outside handle toward you and then close the door.
Lock release button
LOCKING AND UNLOCKING WITH KEY (on some models) Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward.
LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob downward. To unlock: Push the knob upward. To open the sliding door, push the lock release button and then open the door.
16
2001 MY SIENNA (OM45406U)
lock
Vehicles with power door sys- tem—The sliding doors will be locked si- multaneously when either front door or the back door is locked with the power door lock switch or key. If you lock either front door or the back door with the power door lock switch or key while the sliding door is open, the sliding door will be locked after it is closed. (For instructions, see “Front doors” or “Back door” in this sec- tion.) Closing the sliding door with the lock knob in the lock position will also lock the slid- ing door. Be careful not to lock your keys in the vehicle. CLOSING FROM INSIDE To close push the close the door.
fully−opened sliding door, then
the lock release button and
01 SIENNA_U (L/O0008)
D When the vehicle is stopped on a gradient, the door will slide faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door.
the door
D When stopping on a downward slope, open fully while passengers are getting on or off. Do not pull the outside handle or push the lock release button while the door is open as the door could suddenly close by itself causing in- jury.
NOTICE
Do not close the sliding door by ap- plying the brakes. Doing so could cause the door to be damaged.
CAUTION
D When closing the sliding door, con- firm safety of the area around. Keep the heads, hands and other parts of the bodies of all occupants away from the sliding door. Other- wise, they will be possibly caught and pinched by the closing door causing an unexpected serious inju- ry.
2001 MY SIENNA (OM45406U)
17
01 SIENNA_U (L/O0008)
Vehicles with power sliding door system— If the power sliding door system is on, the child−protector feature is cancelled when someone pushes one of the “DOOR L”, “DOOR R” and “POWER DOOR” switches the vehicle or “POWER DOOR”, inside “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter.
CAUTION
Make sure to turn off the power slid- ing door system after the child−protectors.
locking
SLIDING DOOR CHILD−PROTECTORS Open the sliding door fully and move the lock lever to the “LOCK” position as shown on the label. Then close the sliding door. If the child−protector is locked, you cannot open the sliding door from the inside. We recommend using feature whenever small children are in the vehicle.
this
DOOR
SLIDING
HALF−OPENED STOPPER When opening the left side sliding door, it stops at the half−opened position if the fuel filler door is opened. Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is open.
NOTICE
Avoid forcibly opening the left side sliding door refueling. Otherwise, the fuel filler door may be damaged.
fully when
18
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Power sliding door Some vehicles are equipped with a power sliding door. This system has the following functions: D The power sliding door can be oper- ated with the “DOOR L”, “DOOR R” and “POWER DOOR” switches inside the vehicle or “POWER DOOR”, “D− PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter. (For details about the wire- less transmitter, see “Wireless remote control” in this sec- tion.)
remote control
D If you move the sliding door
to the opening or closing direction by hand, the sliding door will automatically and completely open or close after you let go of the sliding door.
CAUTION
Do not leave small children or pets unattended in your vehicle. They could operate the power sliding door, and they themselves or others could be injured. Turn off the power sliding door system when the power sliding door is not in use.
or
“POWER DOOR”,
When the power sliding door system is on, you can open and close the sliding door with the “DOOR L”, “DOOR R” and “POWER DOOR” switches inside the ve- hicle “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless transmitter even if the sliding door child−protector is locked. If small children or pets are in the vehicle, turn off the system to prevent the accidental operation of the door.
remote control
the power sliding door,
“PWR DOOR OFF” SWITCH This switch is used to turn on and off the power sliding door system. For op- erating the “PWR DOOR OFF” switch on the instru- ment panel must be pushed out. (The orange line on the top of the switch indicates that the system is on.) To dis- able the power sliding door feature, push in the switch.
CAUTION
When jacking up the vehicle, turn off the power sliding door system and close the sliding door completely.
NOTICE
When your vehicle goes through an automatic car wash, make sure the power sliding door system is off.
2001 MY SIENNA (OM45406U)
19
01 SIENNA_U (L/O0008)
“DOOR L”, “DOOR R” AND “POWER DOOR” SWITCHES These switches are used to open and close the power sliding door. Push and release one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches. Opening and closing can be performed by the “PWR DOOR” switches under the following con- ditions: D The sliding door is unlocked. D The power sliding door system is on. is
“PWR DOOR OFF” switch
“DOOR R” and
“DOOR L”,
(The pushed out.)
Instrument panel
D To open the power sliding door when the ignition key is in the “ON” position, the transmission selector lever must be in “P”. (To close the sliding door from the fully−opened or half−opened posi- tion, the transmission selector lever is not required to be in “P”.)
Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.
Center pillar
20
2001 MY SIENNA (OM45406U)
CAUTION
If you shift the automatic transmis- sion selector lever out of “P” and accelerate before the power sliding door is closed completely, the sliding door may reverse to the open posi- tion. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you start driving.
OPENING BY HAND
When the power sliding door system is
on, if you pull the outside door handle or
push the inside lock release button to re-
lease the sliding door, it will then automat-
ically and completely open.
When the power sliding door system is
off, open the sliding door as usual.
CLOSING BY HAND
When the power sliding door system is
on, if you slide the door about 10 cm (4
in.) to the closing direction and let the
door go,
it will automatically and com-
pletely close.
When the power sliding door system is
off, close the sliding door as usual.
01 SIENNA_U (L/O0008)
“DOOR R” and inside
If you forcibly close the power sliding door by hand when the ignition key is in the “ON” position, the open power sliding door warning light may stay on. In this case, try opening and closing the power sliding door again by hand slowly, or use one of the “DOOR L”, “PWR DOOR” switches the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter. If you shift out of “P” when the power sliding door is opened or in the process of closing with the power sliding door sys- tem on, a buzzer will sound and the open power sliding door warning light will flash. This is a warning that the sliding door is not completely closed.
the
JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power sliding door while it is closing or opening, the sliding door will automatically reverse to the opposite di- rection. However, if the power sliding door is between fully−closed and half− opened positions while it is opening, the door will stop at that position. Before operating the power sliding door, make sure there is nobody near the slid- ing door. Make sure the sliding door stops at the fully−opened position, and then al- low the passengers to get on and off the vehicle.
2001 MY SIENNA (OM45406U)
21
DOOR
POWER
OPEN SLIDING WARNING LIGHT AND BUZZER This light on the instrument panel comes on if the power sliding door is not com- pletely closed with the ignition key in the “ON” position. (See “Service reminder indi- cators and warning buzzers” in Section 1−5.)
01 SIENNA_U (L/O0008)
The resistance must be as strong as the force of the moving door, or stronger. As the sliding door approaches fully− closed or fully−opened position, its moving force increases significantly. If the sliding door receives a strong im- pact, this function may work even if noth- ing is caught.
the
CAUTION
Power sliding door could injure people if they are caught in the door path. When using the power sliding door, observe the following: D Never try jamming any part of your jam protection
body to make the function work intentionally.
D You must always make sure
the heads, hands and other parts of the bodies of all occupants are away from the sliding door. If someone’s neck, head or hand gets caught in a closing sliding door, it could re- sult in a serious injury. When any- one closes the power sliding door, make sure he/she operates the slid- ing door safely.
NOTICE
Objects caught in the path of the slid- ing door may be damaged. Make sure there is nothing in the doorway be- fore closing the sliding door.
D The
jam protection
function may not work if something gets caught just before the sliding door is fully closed.
22
2001 MY SIENNA (OM45406U)
CAUTION
When the vehicle is stopped on a downward slope of a steep grade (17% or more), the sliding door may not stay in the fully−opened position and could suddenly close by itself, possibly resulting a personal injury. Making sure the sliding door does not close abruptly, the power sliding door system. Then the sliding door will operate under the control of the electric power.
turn on
THE POWER SLIDING
RESETTING DOOR SYSTEM If the power sliding door system operates incorrectly or does not operate under the following conditions, the system must be initialized and reset by the steps in the next column. D The battery is disconnected and then reconnected, or a discharged battery is recharged. In system by doing from 6 to 10.
initialize and reset the following steps
this case,
the
D The open power sliding door warning light stays on though the sliding door is closed. In system by doing from 1 to 10.
initialize and reset the following steps
this case,
the
CAUTION
To initialize and reset power sliding door system, stop the vehicle on a level ground.
01 SIENNA_U (L/O0008)
If the power sliding door system does not operate properly after the above proce- dure, there may be a problem in the sys- tem. Contact your Toyota dealer.
1. Be sure to turn off the power sliding door system by pushing in the “PWR DOOR OFF” switch.
2. Disconnect
the battery
for 1 minute
and then reconnect it.
3. Close the sliding door by hand.
(Step 3 can be performed before step 2.)
4. Turn on the power sliding door system by pushing out the “PWR DOOR OFF” switch.
5. Wait 5 seconds. 6. Open the sliding door by using one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches.
7. Wait 3 seconds after the sliding door
stops at the fully−opened position.
8. Close the sliding door by using one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches inside the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wire- less remote control transmitter.
9. Wait 3 seconds after the sliding door
stops at the fully−closed position.
10. Repeat the steps from 6 to 9.
2001 MY SIENNA (OM45406U)
23
01 SIENNA_U (L/O0008)
Wireless remote control
Locking operation
Unlocking operation
24
to
THE
AND
UNLOCKING
The wireless remote control system al- lows you lock or unlock all the doors from a distance within approxi- mately 1 m (3 ft.) of the vehicle. On some models, the system also allows you to activate the theft deterrent sys- tem from the same distance. LOCKING DOORS To lock and unlock all the doors, push the switches of the transmitter slowly and securely. To lock: Push the “LOCK” switch. All the doors are locked simultaneously. At this time one beep will be heard, parking lights, side marker lights, tail lights and other exterior lights will flash once. Left and right side power sliding door models—If is kept pressed in, the panic mode will work. (For details, see “PANIC (LOCK)” SWITCH.) Check to see that the doors are securely locked. If any of the doors is not securely closed, in the ignition switch, or locking cannot be performed by the “LOCK” switch and a beep will sound con- tinuously for 10 seconds. However, if the key is in the ignition, a beep will not sound.
“LOCK” switch
the key
the
is
if
2001 MY SIENNA (OM45406U)
the to unlock only
To stop the beep, close all the doors se- curely or push the “UNLOCK” switch. “UNLOCK” switch To unlock: Push once the driver’s door. Pushing the switch twice within 3 seconds unlocks all the doors simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights, side marker lights and tail lights will flash twice. When the “UNLOCK” switch is pressed, the personal lights, interior lights and/or ignition key light come on. The lights re- mains on for about 15 seconds unless any of the doors are opened then and closed. “Personal (For lights”, “Ignition switch light” in Section 1−4.) You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the doors will automatically lock again. If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera- tion is not repeated. Release the button and then push again.
information, see
lights” and/or
“Interior
further
SWITCHING BEEP SOUND ON AND OFF You can switch the beep on and off. (The beep is on initially and after battery re- placement.) To switch the beep on and off: With the driver’s door opened— 1. Insert the ignition key and remove it. 2. Within 5 seconds,
ignition key again and turn it to the “ON” posi- tion.
insert
the
3. After 10 seconds, push
the same “LOCK”, “UNLOCK” or “PANIC” button twice within 10 seconds. Two beep sounds inform you that the program has been switched on or off. If this procedure is not followed exactly, the beep will not operate as expected. Check the beep ON/OFF operation by pushing the wireless remote control trans- mitter switch after you finish this proce- dure. the beep does not operate as expected, repeat this procedure from step 1.
If
01 SIENNA_U (L/O0008)
the switch. The sliding
“POWER DOOR”, “D−PWR DOOR” AND “P−PWR DOOR” SWITCHES (on some models) This switch of the wireless remote con- trol transmitter is used to open and close the power sliding door. Push the switch slowly and securely. To open: Push door opens completely. To close: Push the switch again. The slid- ing door closes completely. Opening and closing can be performed by the “D−PWR DOOR” and “P−PWR DOOR” switches under the following conditions only: D The sliding door is unlocked. D The power sliding door system is on. is
“PWR DOOR OFF” switch
“POWER DOOR”,
(The pushed out.)
Right side only power sliding door mod- els
D The
ignition key
is not
in
the “ON”
position.
Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.
Left and right side power sliding door models
2001 MY SIENNA (OM45406U)
25
01 SIENNA_U (L/O0008)
The alarm will last for one minute. To stop alarm midway, do the following: D Push any of the switch on the wireless
remote control transmitter.
D Lock or unlock either front doors or
back door with the key.
D Turn the ignition key from the “LOCK”
to “ON” position.
The panic mode does not work when the ignition key is in the “ON” position.
the
and holding
“PANIC (LOCK)” SWITCH (left and right side power sliding door models) Pushing “PANIC (LOCK)” switch blows the horn intermit- tently and flashes the headlights, tail lights and other exterior lights. The “PANIC (LOCK)” switch is used to deter vehicle theft when you witness any- one attempting to break into or damage your vehicle.
26
2001 MY SIENNA (OM45406U)
intermittently and
“PANIC” SWITCH (right side only power sliding door models) Pushing the “PANIC” switch blows the horn the headlights, tail lights and other exterior lights. The “PANIC” switch is used to deter ve- hicle theft when you witness anyone at- tempting into or damage your vehicle.
to break
flashes
01 SIENNA_U (L/O0008)
MODEL/FCC ID: GQ43VT14T
CAN: 1470102849
MADE IN U.S.A.
This complies with Part 15 of the FCC
rules. Operation is subject to the follow-
ing two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, includ-
ing interference that may cause unde-
sired operation.
for
transmitters
You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information. If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: D Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.
D The battery may have been consumed. Check the battery in the transmitter. To replace the battery, see “REPLACING TRANSMITTER BATTERY”.
If you lose your wireless remote control transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” in Section 4.)
The alarm will last for one minute. To stop alarm midway, do the following: D Push any of the switch on the wireless
remote control transmitter.
D Lock or unlock either front doors or
back door with the key.
D Turn the key from the “LOCK” to “ON”
position.
REMOTE
CONTROL
The panic mode does not work when the key is in the “ON” position. WIRELESS TRANSMITTER The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause to damage remote control transmitter. D Do not leave the wireless remote con- trol the temperature becomes high such as on the dashboard.
transmitter on places where
the wireless
D Do not disassemble it. D Avoid knocking
it hard against other
objects or dropping it.
D Avoid putting it in water.
2001 MY SIENNA (OM45406U)
27
01 SIENNA_U (L/O0008)
REPLACING TRANSMITTER BATTERY For replacement, use a CR2032 lithium battery or equivalent.
CAUTION
Special care should be that small children do not swallow the re- moved transmitter battery or compo- nents.
taken
NOTICE
When replacing the transmitter bat- tery, be careful not to lose the com- ponents.
Replace the transmitter battery by the fol- lowing procedures:
1. Using a coin or equivalent, open the
2. Remove the discharged transmitter bat-
transmitter case.
tery.
NOTICE
Do not bend the terminals.
28
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
replacing battery, check
After the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.
that
Power windows
The windows can be operated with the switch on each front door. The power windows work when the ignition switch is in the “ON” position. OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Lightly pull up the switch.
2001 MY SIENNA (OM45406U)
29
3. Put a new transmitter battery with posi-
tive (+) side up.
Close the transmitter case securely.
NOTICE
z Make sure
the positive side and negative side of the transmitter bat- tery should be faced correctly.
z Be careful not to bend the electrode of the transmitter battery insertion and that dust or oils do not adhere to the transmitter case.
z Close the transmitter case securely.
01 SIENNA_U (L/O0008)
Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. It stops working when either front door is opened.
CAUTION
D Never try jamming any part of your jam protection
body to make the function work intentionally.
Window lock switch
D The
jam protection
function may not work if something gets caught just before fully closed.
the window
is
Automatic operation: Push the switch completely down or pull it completely up, and then release it. The window will fully open or close. To stop the window part- way, lightly move the switch in the oppo- site direction and then release it. Jam protection function: During automat- ic closing operation, the window stops and opens half way if something gets caught between the window and window frame. If the window receives a strong impact, this function may work even if nothing is caught.
THE
that controls
PASSENGER’S
the switch on
OPERATING WINDOW Use the passenger’s door. The driver’s door also has the switch the passenger’s window. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passenger’s window cannot be operated.
30
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
CAUTION
To avoid serious personal injury, you must do the following. D Always make sure the heads, hands and other parts of the bodies of all occupants are kept completely in- side the vehicle before you close the power windows. If someone’s neck, head or hands gets caught in a closing window, it could result in a serious injury. When anyone closes the power windows, make sure that he/she operates the win- dows safely.
D When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.
them
D Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power window switches and get in a window. Unat- tended children can be involved in serious accidents.
trapped
Power rear quarter windows
The rear quarter windows can be oper- ated with the “REAR VENT” switch on the instrument panel. rear quarter windows work The power when the ignition switch is in the “ON” position. Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either is opened. Both the left and the right rear quarter windows move as long as you hold the switch.
front door
2001 MY SIENNA (OM45406U)
31
01 SIENNA_U (L/O0008)
Center side windows and manual rear quarter windows
D Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power rear quarter window switch and get trapped in a window. Unattended children can be involved in serious accidents.
To open the window, pull the latch han- dle toward you and swing it fully out. When closing the window, make sure it is completely closed.
To open: Push the switch on the upper side. To close: Push the switch on the lower side.
CAUTION
To avoid serious personal injury, you must do the following. D Always make sure the hands and other parts of the bodies of all oc- cupants are kept completely inside the vehicle before you close the power If someone’s hands get caught in a closing window, it could result in a serious injury. When anyone closes the power rear quarter windows, make sure that he/she operates the windows safely.
rear quarter windows.
D When small children are in the ve- hicle, never let them use the power rear quarter window switches with- out supervision.
32
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Back door
Insert the key into the keyhole and turn it. To lock: Turn the key clockwise. To unlock: Turn the key counterclockwise. To open the back door, pull the lever. Vehicles with power door lock system—All the doors lock and unlock simultaneously with back door.
Strap
Handle
When closing the back door, use the inside strap or handle for easier reach to the back door. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See in Section 2 for precautions in loading lug- gage.
“Luggage stowage precautions”
CAUTION
Keep the back door closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.
NOTICE
To prevent damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.
2001 MY SIENNA (OM45406U)
33
01 SIENNA_U (L/O0008)
Hood
To open the hood: 1. Pull the hood lock release lever. The
hood will spring up slightly.
CAUTION
Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.
2. In front of the vehicle, pull up the the
lever and
lift
auxiliary catch hood.
3. Hold the hood open by inserting the
support rod into the slot.
Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood make sure it If necessary, press down gently on the front edge to lock it.
the support rod
into place.
locks
to
CAUTION
After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.
34
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Theft deterrent system
To deter the vehicle theft, the system is designed to give an alarm if any of the front, sliding or back doors or hood is forcibly unlocked or the battery ter- minal is disconnected and then recon- nected when the vehicle is locked. The alarm blows the horn intermittently and flashes the headlights, tail lights and other exterior lights.
As the doors are locked, the system will give you a preparation time of 30 seconds before the setting, during which the front, sliding or back doors and hood may be opened. Be careful not to unlock any door with the key or wireless remote control transmitter during setting. This will cancel the system. light 4. After making sure starts flashing, you may leave the ve- hicle.
indicator
the
The system will automatically be set after the preparation time passes. The indicator light will flash to show the system is set. If any of the front, sliding or back doors or hood is open at that time, the setting is interrupted until it is closed and locked. Never leave anyone in the vehicle when you set the system, because unlocking from the inside will activate the system.
SETTING THE SYSTEM 1. Turn
the ignition key position and remove it.
to the “LOCK”
is
removed
The indicator light will start flashing when the key ignition switch. (See “Engine immobiliser system” for details.) 2. Have all passengers get out of
from
the
the
vehicle.
3. Close the front, sliding and back doors and hood. Then lock all the doors with the key or wireless remote control transmitter.
The indicator light will come on when the front, sliding and back doors and hood are closed and locked.
2001 MY SIENNA (OM45406U)
35
01 SIENNA_U (L/O0008)
the system does not work properly,
If have it checked by your Toyota dealer.
described
The alarm will activate again under the same circumstances in “Activating the system”. Stopping the alarm To stop alarm midway, do the following: D Unlock either front door or back door with the key or wireless remote control transmitter.
WHEN THE SYSTEM IS SET Activating the system The system will give the alarm under the following conditions: D If any of
front, sliding or back doors the hood is forcibly opened without the key or wire- less remote control transmitter
is unlocked or
the
if
D If the battery terminal is disconnected
D Turn the key from the “LOCK” to “ON”
and then reconnected
position.
The indicator light will come on when the system is activating. If any of the doors is unlocked without the key or wireless remote control transmitter and the key is not in the ignition switch, all the doors will be automatically locked again. After 1 minute, the alarm will automatically stop and the indicator light will start flash- ing again. Reactivating the alarm Once set, the system cannot be cancelled without the key or wireless remote control transmitter. If the front, sliding and back doors and hood are closed after the alarm stops, the system automatically resets the alarm.
the system at
the
These ways cancel same time. TESTING THE SYSTEM 1. Open all the windows. 2. Set
the system as described above. The doors should be locked with the key or wireless remote control transmit- ter. Be sure to wait until the indicator light goes off or starts flashing.
3. Unlock any door from the inside. The
system should activate the alarm.
this operation
4. Cancel the system as described above. 5. Repeat the other doors and hood. When testing on the hood, also check that the system is activated when the battery terminal is disconnected and then reconnected.
for
36
2001 MY SIENNA (OM45406U)
01 SIENNA_U (L/O0008)
Fuel tank cap
This indicates that the fuel filler door is on the left side of your vehicle.
With tachometer
Without tachometer
1. To open the fuel filler door, pull the
lever up. When refueling, turn off the engine.
CAUTION
D Do not smoke, cause sparks or al- flames when refueling.
low open The fumes are flammable.
D When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck is suddenly re- moved.
the cap
if
2001 MY SIENNA (OM45406U)
37
NOTICE
the
filler door Avoid opening when the left side sliding door is fully opened. Otherwise, the fuel filler door may be damaged.
fuel
01 SIENNA_U (L/O0008)
The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. The left side sliding door does not open fully if the fuel filler door is opened. Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.
CAUTION