2006 Toyota Sienna Owners Manual

You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information.

transmitters

for

If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: (cid:1) Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.

(cid:1) The battery may have been consumed. Check the battery in the transmitter. To replace the battery, see “—Replacing battery” on page 20.

If you lose your wireless remote control transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” on page 439 in Section 4.)

MADE IN U.S.A. This complies with Part 15 of the FCC rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.

15

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Locking and unlocking doors

Locking operation (type A)

Locking operation (type B)

Unlocking operation (type A)

Unlocking operation (type B)

16

this

To lock and unlock all the doors, push the switches of the transmitter slowly and securely. To lock: Push the lock switch. All the side doors and back door are locked simulta- neously. At time one beep will be heard, turn signal lights will flash once. Check to see that the doors are securely locked. If any of the side doors or back door is not securely closed, or if the key is in the ignition switch, locking cannot be per- formed by the lock switch and a beep will sound continuously for 10 seconds. How- ever, if the key is in the ignition switch, a beep will not sound. To stop the beep, close all the side doors and back door securely or push the un- lock switch. The buzzer can be disabled. For details, contact your Toyota dealer. To unlock: Push the unlock switch once to unlock only the driver’s door. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simulta- neously. Each time the unlock switch is pushed, two beeps will be heard, turn sig- nal lights will flash twice.

2006 SIENNA from March ‘06 Prod. (OM45443U)

lights and

This double switch operation to unlock all the side doors and back door can be changed to a single switch operation. For details, contact your Toyota dealer. When the unlock switch is pressed, the front personal ignition switch light come on. The lights remains on for about 15 seconds unless any of the side doors or back door are opened then and closed. (For further information, see “Front personal lights” on page 176 and/or “Igni- tion switch light” on page 179 in Section 1- 5.) You have 60 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will automatical- ly lock again. The lock function can be changed. For details, con- tact your Toyota dealer. is kept If pressed in, the locking or unlocking opera- tion is not repeated. Release the switch and then push again.

lock or unlock switch

the automatic door

timing

the

for

06 SIENNA_U (L/O 0603)

—Opening and closing sliding doors

The following adjustments can be made in this system. For details, contact your Toyota dealer. (cid:1) Cancelling the wireless door locking or

unlocking function

(cid:1) Cancelling the flash of the turn signal

lights

(cid:1) Cancelling the beep sound

Right side power sliding door (type A)

Right side power sliding door (type B)

17

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

The sliding door operation by the wireless remote control can be changed or dis- abled. For details, contact your Toyota dealer.

Opening operation can be performed by the switches under the following conditions only: (cid:1) The sliding door is unlocked. (cid:1) The power sliding door system is on. (The “SLIDE DOOR OFF” switch on the instrument panel is pushed out.)

(cid:1) The key is not in the ignition switch. (cid:1) The sliding door is between the fully- closed position and half- opened posi- tion.

Left side power sliding door (type B only)

the sliding door open

Push and hold the switch of the wire- less remote control transmitter about one second. The power sliding door opens and closes completely. Right side power sliding door— To open: Push switch (right side). To close: Push switch (right side) again. Left side power sliding door— To open: Push switch (left side). To close: Push switch (left side) again.

the sliding door open

the sliding door open

the sliding door open

the

fuel

The sliding door stops at the half- opened position when the window is opened more than about 15 cm (6 in.). The left side power sliding door does not operate when is opened. Closing operation can be performed by the wireless remote control switches under the following conditions only: (cid:1) The power sliding door system is on. (The “SLIDE DOOR OFF” switch on the instrument panel is pushed out.)

filler door

(cid:1) The key is not in the ignition switch. (cid:1) The sliding door is between the fully- opened position and half- opened posi- tion.

18

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Opening and closing back door (type B only)

—Activating alarm

Opening operation can be performed by the switch under the following conditions only: (cid:1) The back door is unlocked. (cid:1) The power back door system

is on. (The “BACK DOOR OFF” switch on the instrument panel is pushed out.)

(cid:1) The key is not in the ignition switch. (cid:1) The back door is between the fully- closed position and half- opened posi- tion.

Closing operation can be performed by the switch under the following conditions only: (cid:1) The power back door system is on. (The “BACK DOOR OFF” switch on the instrument panel is pushed out.)

(cid:1) The key is not in the ignition switch. (cid:1) The back door is between the fully- opened position and half- opened posi- tion.

The back door operation by the wireless remote control can be changed or dis- abled. For details, contact your Toyota dealer.

Push and hold the back door open switch on the wireless remote control transmitter for about one second. The power back door opens and closes completely. When closing or opening the back door, two beeps will be heard and the turn sig- nal lights will flash twice.

the horn

Pushing and holding the alarm switch blows intermittently and flashes the headlights, tail lights and turns on the front personal lights. The alarm switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, do the following: (cid:1) Push any of the switch on the wireless

remote control transmitter.

(cid:1) Lock or unlock either front doors or

back door with the key.

(cid:1) Turn the ignition key from the “LOCK”

to “ON” position.

19

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

The alarm does not work when the ignition key is in the “ON” position. This alarm function can be disabled. For details, contact your Toyota dealer.

—Replacing battery For replacement, use a CR2032 lithium battery or equivalent.

CAUTION

Special care should be taken to pre- vent small children from swallowing the removed transmitter battery or components.

NOTICE

(cid:1) When replacing the transmitter bat- tery, be careful not to lose the com- ponents.

(cid:1) Replace only with the same or equivalent type recommended by a Toyota dealer.

(cid:1) Dispose of used batteries according

to the local laws.

Replace the transmitter battery by follow- ing these procedures:

1. Using a coin or equivalent, open the

transmitter case.

20

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

(cid:1) Be careful not to bend the electrode when inserting the transmitter bat- tery and that dust or oils do not adhere to the transmitter case.

(cid:1) Close the transmitter case securely.

replacing battery, check

the After transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.

that

2. Remove the discharged transmitter bat-

3. Put in a new transmitter battery with

tery.

NOTICE

Do not bend the terminals.

positive (+) side up.

Close the transmitter case securely.

NOTICE

(cid:1) Make sure the positive side and negative side of the transmitter bat- tery are faced correctly.

(cid:1) Do not replace the battery with wet hands. Water may cause unexpected rust.

(cid:1) Do not touch or move any compo- nents inside the transmitter, or it may interfere with proper operation.

21

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Front doors

When either front door is unlocked with a key, the front personal lights and ignition switch light will come on and remain on for about 15 seconds before fading out. (For details, see “Front personal lights” on page 176 and “Ignition switch light” on page 179 in Section 1- 5.)

LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. All the side doors and back door lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice the doors simultaneously. This double key turning operation to un- lock all the side doors and back door can be changed to a single key turning opera- tion. For details, contact your Toyota deal- er.

in succession will unlock all

22

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. The front doors can be opened by pulling the inside handles even if the lock knobs are in the locked position.

2006 SIENNA from March ‘06 Prod. (OM45443U)

CAUTION

Do not pull the inside handle of the front doors while driving. The doors will open and an accident may occur. Toyota strongly recommends that all children be placed in the rear seat of the vehicle.

Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. The front doors cannot be locked if you leave the key in the ignition switch.

Driver’s side

06 SIENNA_U (L/O 0603)

lock: Push the switch down on the

LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To front side. To unlock: Push the switch down on the rear side. Operating the switch simultaneously locks or unlocks all the side doors and back door. If you do either of the following, no side door or back door can be unlocked with the power door lock switch. (cid:1) Lock all the side doors and back door with the key or wireless remote control transmitter when all the side doors and back door are closed.

(cid:1) Open the driver’s door or front passen- ger’s door and move the inside lock knobs of both front doors to the lock position, then close the front doors.

Front passenger’s side

23

2006 SIENNA from March ‘06 Prod. (OM45443U)

The power door lock switch can be reset in the following ways. (cid:1) Turn the ignition key to “ON”. (cid:1) Unlock all

the side doors and back door with the key or wireless remote control transmitter.

(cid:1) Unlock the driver’s door or front pas- lock the doors the power door

senger’s door with knob, and then unlock all and back door with lock switch.

inside

the

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle in an accident. It also helps pre- vent the doors from being opened unintentionally.

24

06 SIENNA_U (L/O 0603)

—Automatic door locking and unlocking functions AUTOMATIC DOOR LOCKING You can select the following functions: (cid:1) Locking linked with the shift position All doors are automatically locked when the selector lever is moved out of “P” position.

(cid:1) Locking linked with vehicle speed

All doors are automatically locked when the vehicle speed goes above about 20
km/h (12 mph).

You can set or cancel the automatic door locking functions: Be sure to apply the parking brake when performing the following operations. To select the locking linked with the shift position: 1. Close all doors and turn the ignition

key to the “ON” position.

2. Shift the selector lever to the “P” posi-

tion.

3. Within 10 seconds of turning the igni- tion key to the “ON” position, press and hold the driver’s side power door lock switch in the lock position for 5
seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again. To select the locking linked with the vehicle speed: 1. Close all doors and turn the ignition

key to the “ON” position.

2. Shift the selector lever from “P” to the

“N” position.

3. Within 10 seconds of turning the igni- tion key to the “ON” position, press and hold the driver’s side power door lock switch in the lock position for 5
seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again.

2006 SIENNA from March ‘06 Prod. (OM45443U)

AUTOMATIC DOOR UNLOCKING You can select the following functions: (cid:1) Unlocking linked with the shift posi-

tion All doors are automatically unlocked when the selector lever is moved to “P” position.

(cid:1) Unlocking

linked with

the

ignition

switch All doors are automatically unlocked when the driver’s door is opened within 10 seconds after is turned to the “ACC” or “LOCK” posi- tion, or the key is removed.

ignition key

the

You can set or cancel the automatic door unlocking functions: Be sure to apply the parking brake when performing the following operations. To select the unlocking linked with the shift position: 1. Close all doors and turn the ignition

key to the “ON” position.

2. Shift the selector lever to the “P” posi-

tion.

06 SIENNA_U (L/O 0603)

Sliding doors (non- powered)

3. Within 10 seconds of turning the igni- tion key to the “ON” position, press and hold the driver’s side power door lock switch in the unlock position for 5 seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again. To select the unlocking linked with the ignition switch: 1. Close all doors and turn the ignition

key to the “ON” position.

2. Shift the selector lever from “P” to the

“N” position.

3. Within 10 seconds of turning the igni- tion key to the “ON” position, press and hold the driver’s side power door lock switch in the unlock position for 5 seconds and then release. The doors will be locked and unlocked to indicate that the function is set.

To cancel the function, do the above op- eration again.

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Move the knob forward. To unlock: Move the knob backward. Closing the sliding door with the lock knob in the lock position will also lock the slid- ing door. Be careful not to lock your keys in the vehicle.

25

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CLOSING THE FULLY- OPENED SLIDING DOOR To close the fully- opened sliding door, pull the then close the door.

inside or outside handle and

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps from being prevent thrown out from the vehicle in an accident. It also helps prevent the doors from being opened unintention- ally.

the passengers

26

CAUTION

(cid:1) When closing the sliding door, con- firm safety of the area around. Keep the heads, hands and other parts of the bodies of all occupants away from the sliding door. Other- wise, the closing door may cause an unexpected serious injury.

the door will slide

(cid:1) When the vehicle is stopped on a slope, faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door.

the door

(cid:1) When stopping on a downward slope, open fully while passengers are getting on or off. Do not pull the outside handle or inside handle while is open as the door could suddenly close by itself causing injury.

the door

NOTICE

Do not close the sliding door by ap- plying the brakes. Doing so could cause the door to be damaged.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

When the fuel filler door is opened, the left side sliding door will not open. Close the fuel filler door securely and then operate the sliding door.

NOTICE

Avoid forcibly opening the left side sliding door fully when the fuel filler door is opened. Otherwise, the fuel filler door may be damaged.

the sliding door window

When is opened more than about 15 cm (6 in.), the sliding door will stop at half- opened position reasons. Close the window and then operate the sliding door.

for safety

CAUTION

latched at this position.

Do not leave the sliding door at half- opened position because the door is not If the vehicle is stopped on a downward slope, it may move and cause an un- expected injury.

SLIDING DOOR CHILD- PROTECTORS Open the sliding door fully and move the lock lever to the “LOCK” position as shown on the label. Then close the sliding door. If the child- protector is locked, you cannot open the sliding door from the inside. We recommend using feature whenever small children are in the vehicle.

this

27

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

NOTICE

When your vehicle goes through an automatic car wash, make sure the power sliding door system is off.

Power sliding doors—

On

Off

POWER SLIDING DOOR MAIN SWITCH (“SLIDE DOOR OFF” switch) This switch is used to turn on and off the power sliding door system. In order to operate the power sliding door, the “SLIDE DOOR OFF” switch on the in- strument panel must be pushed out. (The orange line on top of the switch indicates that the power sliding door system is on.) To disable the power sliding door feature, push in the switch.

28

When the power sliding door system is on, you can open and close the sliding door with the power sliding door switches on the overhead console or wireless re- mote control transmitter even if the sliding door child- protector is locked. When the power sliding door system is off, you can open and close the sliding door by the same operations as non- pow- ered sliding door. The sliding door closer is operative even if the power sliding door system is off. See page 32 about sliding door closer.

CAUTION

(cid:1) Do not leave small children or pets in your vehicle. They unattended could operate the power sliding door and injure themselves or oth- ers. Turn off the power sliding door system when the power sliding door is not in use.

(cid:1) When jacking up the vehicle, turn off the power sliding door system and close the sliding door com- pletely.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of locking the doors helps seat belts, prevent from being thrown out from the vehicle in an accident. It also helps prevent the doors from being opened unintention- ally.

the passengers

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Move the knob forward. To unlock: Move the knob backward. Closing the sliding door with the lock knob in the lock position will also lock the slid- ing door. Be careful not to lock your keys in the vehicle.

—Operation of power sliding door The power sliding door can be operated automatically in the following ways: (cid:1) Operates with the power sliding door

switches inside the vehicle

(cid:1) Operates with the wireless remote con-

trol transmitter

(cid:1) Assists operation with the outside or

inside handle by hand

the

The power sliding door system can be canceled by “SLIDE DOOR OFF” switch. When the power sliding door system is on, if you put the transmission out of “P” with the ignition key in the “ON” position and is not completely closed, a buzzer will sound.

the sliding door

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the sliding door automatically opens or closes.

(cid:1) Never allow a child to operate the

sliding door.

29

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

NOTICE

Do not apply excessive force when the sliding door is operated automati- cally. Otherwise, the power sliding door system may be damaged.

You can cause a beep to sound when the power sliding door is opened or closed. For details, contact your Toyota dealer.

Front overhead console

OPERATING WITH THE POWER SLIDING DOOR SWITCHES To open the door, push the switch. To close the door, push the switch once again. The door opens and closes com- pletely. Switches on the front overhead con- sole:

” switch—To operate

“ door

the

left side

” switch—To operate the right side

“ door

Switches on the center pillar:

“PWR DOOR” switch—To operate each side door

Opening operation can be performed by the switches under the following condi- tions: (cid:1) The sliding door is unlocked. (cid:1) The power sliding door system is on. is

“SLIDE DOOR OFF” switch

(The pushed out.)

Center pillar

(cid:1) The sliding door is between the fully- closed position and half- opened posi- tion.

30

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

If you shift the automatic transmis- sion selector lever out of “P” and accelerate before the power sliding door is closed completely, the sliding door may reverse to the open posi- tion. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you start driving.

(cid:1) When the ignition key is in the “ON” position, the transmission selector lever must be in “P”.

(cid:1) The

child- protector

is

unlocked.

(switches on the center pillar only)

Closing operation can be performed by the switches under the following condi- tions: (cid:1) The power sliding door system is on. is

“SLIDE DOOR OFF” switch

(The pushed out.)

(cid:1) The sliding door is between the fully- opened position and half- opened posi- tion.

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened. The length of time required to push the switches for operating the sliding door can be changed. For details, contact your Toyota dealer.

” or “

THE WIRELESS

OPERATING WITH REMOTE CONTROL TRANSMITTER To open or close the door, push the ” switch on the wireless “ remote control transmitter about one second. (Only when the power sliding door system is on.) For details, see “Wireless remote control” on page 14
in this Section. ASSISTS THE OUTSIDE OR INSIDE HANDLE BY HAND When the power sliding door system is on (the “SLIDE DOOR OFF” switch is pushed out), if you pull the outside handle or slide the the sliding door will automatically and completely open or close. When the power sliding door system is off, the sliding door can be operated manually by the outside or inside handle.

OPERATION WITH

inside handle,

31

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

inside or outside handle and

CLOSING THE FULLY- OPENED SLIDING DOOR To close the fully- opened sliding door, pull the then close the door. Sliding door closer: When the sliding door has not been fully closed, it is auto- matically closed completely even the power sliding door system is off.

if

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the automatically closes when it has not been fully closed.

sliding

door

(cid:1) Never allow a child to operate the

sliding door.

NOTICE

Do not apply excessive force when the sliding door closer is operating. Otherwise, the sliding door closer may be damaged.

32

Before operating the power sliding door, make sure there is nobody near the slid- ing door. Make sure the sliding door stops at the fully- opened position, and then al- low the passengers to get in and out of the vehicle. The resistance must be as strong as the force of the moving door, or stronger. As the sliding door approaches fully- closed or fully- opened position, its moving force increases significantly. The jam protection function may not work if something gets caught just before the sliding door is fully closed. If the sliding door receives a strong im- pact, this function may operate even if nothing is caught.

the

CAUTION

The power sliding door could injure people if they are caught in the door path. When using the power sliding door, observe the following: (cid:1) Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a serious injury.

JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power sliding door while it is closing or opening, the sliding door will automatically reverse to the opposite di- rection. However, if the power sliding door is between fully- opened positions while it is opening, the door will stop at that position. If function operates continuously at the closing operation more than 2 the sliding door will be stopped at that position and the power sliding door system will be canceled.

the half- opened and

jam protection

times,

the

2006 SIENNA from March ‘06 Prod. (OM45443U)

(cid:1) The

jam protection

function may not work if something gets caught just before the sliding door is fully closed.

(cid:1) Before you close the power sliding door, always make sure there is no- body around it. Also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught in a closing door, it could result injury. When anyone closes the power slid- ing door, make sure he or she oper- ates the door safely.

in death or serious

the vehicle.

inside

NOTICE

Objects caught in the path of the slid- ing door may be damaged. Make sure there is nothing in the doorway be- fore closing the sliding door.

06 SIENNA_U (L/O 0603)

—Power sliding door cautions

In any of

the battery.

If the battery is disconnected or run down, the power sliding door system may not work after you reconnect, replace or recharge these cases, close the sliding doors completely by hand to normalize the power sliding door system. If the power sliding door system does not operate properly after the above proce- dure, there may be a problem in the sys- tem. Contact your Toyota dealer.

CAUTION

(cid:1) When closing the sliding door, con- firm safety of the area around. Keep the heads, hands and other parts of the bodies of all occupants away from the sliding door. Other- wise, the closing door may cause an unexpected serious injury.

the door will slide

(cid:1) When the vehicle is stopped on a slope, faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door.

33

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

the door

(cid:1) When stopping on a downward slope, open fully while passengers are getting on or off. Do not pull the outside handle or inside handle while is open as the door could suddenly close by itself causing injury.

the door

NOTICE

Do not close the sliding door by ap- plying the brakes. Doing so could cause the door to be damaged.

When the fuel filler door is opened, the left side sliding door will not open. Close the fuel filler door securely and then operate the sliding door.

NOTICE

Avoid forcibly opening the left side sliding door fully when the fuel filler door is opened. Otherwise, the fuel filler door may be damaged.

the sliding door window

When is opened more than about 15 cm (6 in.), the sliding door will stop at half- opened position reasons. Close the window and then operate the sliding door.

for safety

34

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Sliding door child- protectors

CAUTION

Make sure to turn off the power slid- ing door system after the child- protectors.

locking

Open the sliding door fully and move the lock lever to the “LOCK” position as shown on the label. Then close the sliding door. When the child- protector is locked, you cannot open the sliding door by the inside door handle. We recommend using this feature whenever small children are in the vehicle.

CAUTION

When the power sliding door is ON— Do not leave the sliding door at half- opened position because the door will unlock after 30 minutes. If the vehicle is stopped on a downward slope, it may move and cause an unexpected injury. When is OFF—Do not leave the sliding door at half- opened position because the door is not latched at this position. If the vehicle is stopped on a down- ward slope, it may move and cause an unexpected injury.

the power sliding door

NOTICE

When the power sliding door is ON— To prevent the battery from being dis- charged, do not leave the sliding door at half-opened position.

35

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Back door (non- powered)

lights and

front personal

When all the side doors and back door are unlocked simultaneously with a key, the ignition switch light will come on and remain on for about 15 seconds before fading out. (For details, see “Front personal lights” on page 176 and “Ignition switch light” on page 179 in Section 1- 5.) If the back door opener does not operate, see “If you cannot operate back door opener” on page 440 in Section 4. If the battery is disconnected or run down, the back door will be automatically locked after you reconnect, replace or re- charge the battery. Be careful not to lock your keys in the vehicle.

When closing the back door, the inside strap can be used to make the reach easier. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See “—Stowage precautions” on page 399
in Section 2 for precautions when loading luggage.

To open the back door, push up the back door opener and raise the door. The back door can be opened when the vehicle is stopped. The back door can be locked or unlocked in the following ways. (cid:1) Operate

lock switch. (See “Front doors” on page 22 in this Section.) (cid:1) Operate

remote control. (See “Wireless remote control” on page 14 in this Section.)

the power door

the wireless

(cid:1) All the side doors and back door are locked and unlocked simultaneously with “Front doors” on page 22 in this Section.)

the driver’s door.

(See

36

2006 SIENNA from March ‘06 Prod. (OM45443U)

CAUTION

Keep the back door closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.

NOTICE

To avoid damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.

06 SIENNA_U (L/O 0603)

Power back door— —“BACK DOOR OFF” switch

On

Off

This switch is used to turn on and off the power back door system. In order to operate the power back door, the “BACK DOOR OFF” switch on the in- strument panel must be pushed out. (The orange line on top of the switch indicates that the power back door sys- tem is on.) To disable the power back door feature, push in the switch.

CAUTION

(cid:1) Do not leave small children or pets unattended in your vehicle. They could operate the power back door, and anyone around the back door could be injured. Turn off the power back door system when the power back door is not in use.

(cid:1) When jacking up the vehicle, turn off the power back door system and close the back door completely.

NOTICE

When your vehicle goes through an automatic car wash, make sure the power back door system is off.

37

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Automatic operation (power back door—ON) The power back door can be operated automatically in the following ways: (cid:1) Operates with

the power back door

switch on the overhead console

(cid:1) Operates with the wireless remote con-

trol transmitter

NOTICE

Do not apply excessive force when the back door is operated automati- cally. Otherwise, the power back door system may be damaged.

is

the

system

canceled,

(cid:1) Assists closing by hand The power back door system can be can- celed by the “BACK DOOR OFF” switch. When see “—Manual operation” on page 41 in this Section. When closing or opening the back door automatically, two beeps will be heard and the turn signal lights will flash twice. The beep sound can be changed. For de- tails, contact your Toyota dealer.

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the back door automatically closes. (cid:1) Never allow a child to operate the

back door.

38

OPERATING WITH THE POWER BACK DOOR SWITCH To open the door, push and hold the ” switch on the overhead con- “ sole about one second. To close the door, push this switch once again. The door opens and closes completely.

2006 SIENNA from March ‘06 Prod. (OM45443U)

Opening operation can be performed by the switch under the following condi- tions: (cid:1) The back door is unlocked. (cid:1) The power back door system

“BACK DOOR OFF” switch

is on. is

(The pushed out.)

(cid:1) The back door is between in the fully- closed position and half- opened posi- tion.

(cid:1) When the ignition key is in the “ON” position, the transmission selector lever must be in “P”.

Closing operation can be performed by the switch under the following condi- tions: (cid:1) The power back door system

“BACK DOOR OFF” switch

is on. is

(The pushed out.)

(cid:1) The back door is between in the fully- opened position and half- opened posi- tion.

The time of pushing the switches for oper- ating the back door can be changed. For details, contact your Toyota dealer.

06 SIENNA_U (L/O 0603)

(Only when

THE WIRELESS

OPERATING WITH REMOTE CONTROL TRANSMITTER To open or close the door, push and ” switch on the wireless hold the “ remote control transmitter about one second. the power back door system is on.) For details, see “Wireless remote control” on page 14
in this Section. ASSISTS CLOSING BY HAND When the power back door system is on (the “BACK DOOR OFF” switch is pushed out), if you move the back door about 10—15 cm (4—6 in.) from its fully- opened position, the back door will automatically and completely close. When the power back door system is off, the back door can be closed manually. The assisting function when closing the back door can be disabled and the assist- ing function when opening the back door can be added. For details, contact your Toyota dealer.

JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power back door while it is closing or opening, the back door will au- tomatically reverse to the opposite direc- tion. If function operates continuously at the closing operation more than 2 the back door will be stopped at that position.

jam protection

times,

the

39

2006 SIENNA from March ‘06 Prod. (OM45443U)

Before operating the power back door, make sure there is nobody near the back door. The resistance must be as strong as the force of the moving door, or stronger. As the back door approaches the fully- closed or fully- opened position, its moving force increases significantly. The jam protection function may not work if something gets caught just before the back door is fully closed. If the back door receives a strong impact, this function may operate even if nothing is caught.

06 SIENNA_U (L/O 0603)

If the battery is disconnected or run down, the back door will be automatically locked and the power back door system may not work after you reconnect, replace or recharge the battery. In any of these cases, normalize the power back door system by following procedure. 1. Unlock

the key, wireless remote control transmitter or power door lock switch.

the back door with

2. Close hand.

the back door completely by

If the power back door system does not operate properly after the above proce- dure, there may be a problem in the sys- tem. Contact your Toyota dealer.

CAUTION

The power back door could injure people if they are caught in the door path. When using the power back door, observe the following: (cid:1) Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a serious injury.

(cid:1) The

jam protection

function may not work if something gets caught just before the sliding door is fully closed.

(cid:1) Before you close the power back door, always make sure there is no- body around it. If someone’s neck, head or hands get caught in a clos- ing door, it could result in death or serious injury. When anyone closes the power back door, make sure he or she operates the door safely.

NOTICE

Objects caught in the path of the back door may be damaged. Make sure there is nothing in the doorway before closing the back door.

40

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Manual operation (power back door—OFF)

lights and

front personal

When all the side doors and back door are unlocked simultaneously with a key, the ignition switch light will come on and remain on for about 15 seconds before fading out. (For details, see “Front personal lights” on page 176 and “Ignition switch light” on page 179 in Section 1- 5.) If the back door opener does not operate, see “If you cannot operate back door opener” on page 440 in Section 4. If the battery is disconnected or run down, the back door will be automatically locked after you reconnect, replace or re- charge the battery. Be careful not to lock your keys in the vehicle.

When closing the back door, the inside strap can be used to make the reach easier. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See “—Stowage precautions” on page 399
in Section 2 for precautions when loading luggage.

To open the back door, push up the back door opener and raise the door. The back door can be opened when the vehicle is stopped. The back door can be locked or unlocked in the following ways. (cid:1) Operate

lock switch. (See “Front doors” on page 22 in this Section.) (cid:1) Operate

remote control. (See “Wireless remote control” on page 14 in this Section.)

the power door

the wireless

(cid:1) All the side doors and back door are locked and unlocked simultaneously with “Front doors” on page 22 in this Section.)

the driver’s door.

(See

41

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Power windows

CAUTION

Keep the back door closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.

NOTICE

To avoid damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.

Back door closer: When the back door has not been fully closed, it is automati- cally closed completely even if the power back door system is off.

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the back door automatically closes when it has not been fully closed. (cid:1) Never allow a child to operate the

back door.

NOTICE

Do not apply excessive force when the back door closer is operating. Otherwise, the back door closer may be damaged.

The windows can be operated with the switch on each front door. The power windows work when the ignition key is in the “ON” position. Key off operation: If both front doors are closed, the front door windows and sliding door windows work for 43 seconds even after the ignition switch is turned off. It stops working when either front door is opened.

42

2006 SIENNA from March ‘06 Prod. (OM45443U)

OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Lightly pull up the switch.

06 SIENNA_U (L/O 0603)

Automatic operation: Type A—Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it. Type B—Push the switch completely down or pull it completely up, and then release it. The window will fully open or close. To stop the window partway, lightly move the switch in the opposite direction and then release it. Jam protection function (type B only): During automatic closing operation, the window stops and opens half way if some- thing gets caught between the window and window frame. If the window receives a strong impact, this function may work even if nothing is caught.

43

2006 SIENNA from March ‘06 Prod. (OM45443U)

Type A (to open only)

Type B (to open and close)

06 SIENNA_U (L/O 0603)

Window lock switch

If the battery is disconnected or run down, the power window may not operate automatically and the jam protection func- tion will not function correctly after you reconnect, replace or recharge the battery. In any of these cases, you should normal- ize the power window. To normalize the power window: 1. Push down the power window switch

and lower the window halfway.

2. Pull up

the switch until

the window closes and hold the switch for a sec- ond.

that

Make sure the window opens and closes automatically. If the power window cannot be operated properly, have it checked by your Toyota dealer.

CAUTION

(cid:1) Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a serious injury.

(cid:1) The

jam protection

function may not work if something gets caught just before fully closed.

the window

is

44

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

THE

PASSENGERS’

OPERATING WINDOWS Use the switch on each passenger’s door or the switches on the driver’s door that control each passenger’s win- dow. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passengers’ windows cannot be operated. The sliding door window cannot be oper- ated when the sliding door is opened.

CAUTION

To avoid serious personal injury, you must do the following. (cid:1) Before you close the power win- dows, always make sure there is nobody around the power windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it could result in death or serious in- jury. When anyone closes the power windows, make sure he or she op- erates the windows safely.

in a closing window,

the vehicle.

inside

(cid:1) When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.

them

(cid:1) Be sure to remove the ignition key

when you leave your vehicle.

(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power window switches and get in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.

trapped

45

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Manual quarter windows

Power quarter windows

Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either is opened.

front door

CAUTION

To open the quarter window, pull the latch handle toward you and swing it fully out. When closing the window, make sure it is completely closed.

The quarter windows can be operated with the “REAR VENT” switch on the instrument panel. The power quarter windows work when the ignition key is in the “ON” position. To open: Push the switch on the upper side. To close: Push the switch on the lower side. Both the left and right rear quarter win- dows move as the switch.

long as you hold

46

To avoid serious personal injury, you must do the following. (cid:1) Before you close the power quarter windows, always make sure there is nobody around the power quarter windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it could result in death or serious in- jury. When anyone closes the power windows, make sure he or she op- erates the windows safely.

in a closing window,

the vehicle.

inside

(cid:1) When small children are in the ve- hicle, never let them use the power quarter window switches without supervision.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Hood

(cid:1) Be sure to remove the ignition key

when you leave your vehicle.

(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power quarter window switch and get trapped in a window. Unattended person (particularly a small child) can be involved in a serious accident.

To open the hood: 1. Pull the hood lock release lever. The

hood will spring up slightly.

CAUTION

Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.

2. In front of the vehicle, pull up the the

lever and

lift

auxiliary catch hood.

47

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Theft deterrent system

CAUTION

After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.

NOTICE

Be sure to return the support rod to its clip before closing the hood. Clos- ing the hood with the support rod up could cause the hood to bend.

3. Hold the hood open by inserting the

support rod into the slot.

To insert the support rod into the slot, move it straight up. If it is moved to the side or toward the inside of the vehicle, it may become detached. Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood and make sure it locks into place. If necessary, press down gently on the front edge to lock it.

the support rod

to

48

To deter the vehicle theft, the system is designed to sound an alarm if any of the side doors, back door or hood is forcibly unlocked or opened or the bat- tery terminal is disconnected and then reconnected when the vehicle is locked. The alarm blows the horn intermittently and flashes the headlights, tail lights and turn signal lights, and turns on the front personal lights.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

The system will automatically be set after 30 seconds. When the system is set, the indicator light will start flashing again. 4. After making sure

light starts flashing, you may leave the ve- hicle.

indicator

the

Never leave anyone in the vehicle when you set the system, because unlocking from the inside will activate the system. CANCELING THE SYSTEM The system can be canceled by the fol- lowing ways: (cid:1) Any of the side doors or the back door is unlocked with the key or wireless remote control transmitter.

for 2 seconds when

(cid:1) Turn the ignition key to “ON” position. If the parking lights and tail lights come on is canceled, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

the system

WHEN THE SYSTEM IS SET Activating the system The system will sound the alarm under the following conditions: (cid:1) If any of the side doors or back door is unlocked or opened without the key or wireless remote control transmitter, or if the hood is forcibly opened.

(cid:1) If the battery terminal is disconnected

and then reconnected.

(cid:1) If the ignition is hotwired. The indicator light will come on when the system is activated. If the alarm has been activated and any of the side doors or back door is un- locked, all the side doors and back door will re- lock automatically. After one minute, the alarm will automati- cally stop and the indicator light will starts flashing again. Reactivating the system Once set, the system is automatically re- set after the alarm stopped automatically after one minute. The alarm will activate again under the same in circumstances “Activating the system”.

described

49

2006 SIENNA from March ‘06 Prod. (OM45443U)

SETTING THE SYSTEM 1. Turn

the ignition key position and remove it.

to the “LOCK”

the

On some models, the indicator light will start flashing when the key is removed from “Engine immobilizer system” on page 13 in this Section for details.) 2. Have all passengers get out of

ignition switch.

(See

the

vehicle.

3. Close and lock all the side doors, back

door and hood.

The indicator light will remain on when all the side doors, back door and hood are closed and locked.

06 SIENNA_U (L/O 0603)

Fuel tank cap

TESTING THE SYSTEM 1. Open all the windows. 2. Set the system as described above. All the side doors and back door should be locked with the key or wireless re- mote control to wait until the indicator light starts flash- ing.

transmitter. Be sure

3. Unlock any side door from the inside. The system should activate the alarm.

for

this operation

4. Stop the alarm as described above. 5. Repeat

the other doors and hood. When the hood, also check that the system is activated when the battery terminal is disconnected and then reconnected. the system does not work properly,

If have it checked by your Toyota dealer.

testing

This indicates that the fuel filler door is on the left side of your vehicle.

Stopping the alarm The alarm will be stopped by the following these ways: (cid:1) Unlock any of the side doors or the back door with the key or wireless re- mote control transmitter.

(cid:1) Turn the ignition key from the “LOCK”

to “ON” position.

the

the system at

These ways cancel same time. If the battery becomes discharged due to the vehicle being unused for a long time, etc., when the battery is recharged or the alarm. If this happens, immediately unlock any of the side doors or the back door with the key or the wireless remote con- trol transmitter, and the alarm will stop.

the system will give

replaced,

50

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

NOTICE

Avoid opening the fuel filler door when the left side sliding door is fully opened. Otherwise, the fuel filler door may be damaged.

2. To remove the fuel tank cap, turn the cap counterclockwise by 90 de-