2008 Toyota Prius Owners Manual

PRIUS_U_(L/O_0802)

1-8. Safety information Installing child restraints

Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the outboard rear seats using a seat belt or a child restraint lower anchor belt. Attach the top strap when install- ing a child restraint.

Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (→P. 66)

Child restraint lower anchor- ages

Lower anchorages are pro- vided for the outboard rear seats. (Buttons displaying the location of the anchorages are attached to the seats.)

Anchor bracket (for top strap) Anchor brackets are provided for all rear seats.

110

PRIUS_U_(L/O_0802)

1

1-8. Safety information

Installing child restraints using a seat belt (child restraint lock function belt)

n Rear facing ⎯ Infant seat/convertible seat STEP 1

Place the child seat on the rear seat facing the rear of the vehi- cle.

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

then allow

Fully extend the shoulder belt and to retract slightly in order to activate the ALR lock mode.

it

Lock mode allows the seat belt to retract only.

111

STEP 2

STEP 3

PRIUS_U_(L/O_0802)

1-8. Safety information

STEP 4

While pushing the child seat down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

n Forward facing ⎯ Convertible seat STEP 1

Place the child seat on the seat facing the front of the vehicle.

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

it

then allow

Fully extend the shoulder strap and to retract slightly into the ALR lock mode. Lock mode allows the seat belt to retract only.

STEP 2

STEP 3

112

PRIUS_U_(L/O_0802)

1

1-8. Safety information

While pushing the child seat into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

Place the booster seat on the seat facing the front of the vehi- cle.

Sit the booster in the child seat. Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child’s shoulder, and that the lap belt is as low as possible. (→P. 64)

113

STEP 4

n Booster seat STEP 1

STEP 2

PRIUS_U_(L/O_0802)

1-8. Safety information

Removing a child restraint installed with a seat belt

Push the buckle release button and fully retract the seat belt.

Installation with child restraint lower anchorages

Type A

STEP 1

STEP 2

Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the anchorages. If the child restraint has a top strap, top strap should be latched onto the anchorage.

the

For owners in Canada: The symbol on a child restraint system indicates the presence of a lower anchorage system.

Canada only

114

PRIUS_U_(L/O_0802)

1

Type B

1-8. Safety information

STEP 1

STEP 2

Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the anchorages. If the child restraint has a top strap, top strap should be latched onto the anchorage.

the

For owners in Canada: The symbol on a child restraint system indicates the presence of a lower anchorage system.

Canada only

Child restraint systems with a top strap

STEP 1

Secure the child restraint using a seat belt or lower anchors, and lock the head restraint in place at the highest position.

115

PRIUS_U_(L/O_0802)

1-8. Safety information

STEP 2

Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top strap. is

top strap

Make sure the securely latched.

STEP 3

Reinstall the head restraint.

ITY18P041

n Laws and regulations pertaining to anchorages

Anchorages conform to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819.

CAUTION

n When installing a booster seat

Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode: (→P. 66) l ALR mode causes the belt to tighten only which could cause injury or dis-

comfort to the child.

l Do not allow the child to play with the seat belt or the child could be killed

or serious injured.

116

PRIUS_U_(L/O_0802)

1

1-8. Safety information

CAUTION

n When installing a child restraint system

Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be injured or even killed in the event of sudden braking or an accident.

If the driver’s seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.

l Only put a forward facing or booster child seat on the front seat when unavoidable. When installing a forward facing or booster child seat on the front passenger seat, move the seat as far back as possible even if “AIR BAG OFF” indicator light is illuminated. Fail- ing to do so may result in death or seri- ous injury if the airbags deploy (inflate).

l When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder. Failing to do so may result in death or serious injury in the event of an accident or sudden braking.

l Ensure the belt and tab are securely locked and that the seat belt is not

twisted.

l Push and pull the child seat in different directions to be sure it is secure. l Follow all installation instructions provided by the child restraint system

manufacturer.

117

PRIUS_U_(L/O_0802)

1-8. Safety information

CAUTION

n Do not use a seat belt extender

If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of a colli- sion.

n To correctly attach a child restraint system to the anchorages

When using the lower anchorages, be sure that there are no foreign objects around the anchorages and that the seat belt is not caught behind the child restraint. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of a sudden stop or accident.

118

PRIUS_U_(L/O_0802)

2-1. Driving procedures Driving the vehicle

The following procedures should be observed to ensure safe driv- ing. n Starting the hybrid system (→P. 131) n Driving STEP 1

Release the parking brake.

With the brake pedal depressed, shift the shift lever to “D”. (→P. 136) (→P. 142) Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle.

STEP 2

STEP 3

n Stopping STEP 1

STEP 2

With the shift lever in “D”, depress the brake pedal. If necessary, set the parking brake. When the vehicle is stopped for an extended period of time, push (→P. 137) the “P” position switch.

n Parking the vehicle STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

With the shift lever in “D”, depress the brake pedal. Set the parking brake. Push the “P” position switch. When parking on hill, if necessary, block the wheels. Press the “POWER” switch and stop the hybrid system. Lock the door, making sure that you have the electronic key on your person.

(→P. 142) (→P. 137)

Starting on a steep incline

STEP 1

STEP 2

STEP 3

Firmly set the parking brake and shift the shift lever to “D”. Gently depress the accelerator pedal. Release the parking brake.

120

PRIUS_U_(L/O_0802)

2-1. Driving procedures

n Driving in the rain

l Drive carefully when it is raining, because visibility will be reduced, the

windows may become fogged-up, and the road will be slippery.

l Drive carefully when it starts to rain, because the road surface will be

especially slippery.

l Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

n Breaking in your new Toyota

To extend the life of the vehicle, the following precautions are recommended to observe: l For the first 180 miles (300 km):

Avoid sudden stops.

l For the first 621 miles (1000 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in the low gears. • Do not drive at a constant speed for extended periods.

n Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 464)

n For efficient use

l Put the shift lever into “D” when driving

In the “N” position, the gasoline engine operates but electricity cannot be generated. The hybrid battery (traction battery) will be discharged requiring unnec- essary engine power to recharge.

l Drive your vehicle smoothly

Avoid abrupt acceleration and deceleration. Gradual acceleration and deceleration will make more effective use of the traction motor without having to use gasoline engine power.

121

PRIUS_U_(L/O_0802)

2-1. Driving procedures

l Avoid repeated acceleration

Repeated acceleration consumes hybrid battery (traction battery) power, resulting in poor acceleration. Battery power can be restored by driving with the accelerator pedal slightly released. l Push the “P” position switch when parking

In the “N” position, the hybrid battery (traction battery) does not recharge. Leaving the shift lever in the “N” position for an extended period of the time may discharge the hybrid battery. The vehicle cannot run if the hybrid battery is discharged.

n Normal characteristics after turning off the hybrid system

Approximately five hours after the hybrid system is turned off, you may hear sound coming from under the vehicle for several minutes. This is because the fuel evaporation leakage check is performed. It does not indicate a mal- function.

122

PRIUS_U_(L/O_0802)

2-1. Driving procedures

CAUTION

n When starting the vehicle

Always keep your foot on the brake pedal while stopped with the hybrid sys- tem running. This prevents the vehicle from creeping.

n When driving the vehicle

l Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly, allowing you to depress the brake and accelerator pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

l The driver should pay attention to pedestrians when the vehicle is pow- ered only by the electric motor (traction motor). Because there is no hybrid system sounds, the pedestrians may misjudge the vehicle’s movement.

l Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. this may cause a fire if there is any flammable material nearby.

l Do not let the vehicle roll backwards while the shift lever is in a driving

position, or roll forward while the shift lever is in “R”. Doing so may cause the hybrid system not to operate or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle. If the smell of exhaust is noticed inside the vehicle, open the windows and check that the back door is closed. Large amounts of exhaust in the vehi- cle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately.

123

PRIUS_U_(L/O_0802)

2-1. Driving procedures

CAUTION

n When driving the vehicle

l Do not under any circumstances shift the shift lever to “R”, “N” or push the

“P” position switch while the vehicle is moving. Doing so can cause significant damage to the transmission and may result in a loss of vehicle control.

l Do not shift the shift lever to “N” while the vehicle is moving.

Doing so may cause the engine brake not to operate properly and lead to an accident.

l Do not turn the hybrid system off while driving.

The power steering and brake actuator will not operate properly if the hybrid system is not running.

l Use engine braking (“B”) to maintain a safe speed when driving down a

steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 136)

l When stopped on an inclined surface, use the brake pedal and parking brake to prevent the vehicle from rolling backward or forward and causing an accident.

l Do not adjust the position of the steering wheel, the seat, or the inside or

outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.

l Always check that all passengers’ arms, heads or other parts of their bod- ies are not outside the vehicle, as this may result in death or serious injury. l Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds.

124

PRIUS_U_(L/O_0802)

2

2-1. Driving procedures

CAUTION

n When driving on slippery road surfaces

l Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

l Sudden changes in engine speed, such as engine braking caused by upshifting or down-shifting, may cause the vehicle to skid, resulting in an accident.

l After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

n When shifting the shift lever

Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

n When the vehicle is stopped

l Do not race the hybrid system.

If the vehicle is in any gear other than “P” or “N” the vehicle may acceler- ate suddenly and unexpectedly, and may cause an accident.

l Do not leave the vehicle with the hybrid system on for a long time.

If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.

l Always keep a foot on the brake pedal while the hybrid system is running

to prevent an accident caused by the vehicle moving.

125

PRIUS_U_(L/O_0802)

2-1. Driving procedures

CAUTION

n When the vehicle is parked

l Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Failure to do so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may lead to a

fire.

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of eye glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle’s electrical components.

l Always apply the parking brake, push the “P” position switch, stop the

hybrid system and lock the vehicle. Do not leave the vehicle unattended while the hybrid system is running.

l Do not touch the exhaust pipe while the hybrid system is running or imme-

diately after turning the hybrid system off. Doing so may cause burns.

l Do not leave the hybrid system operating in an area with snow build up, or where it is snowing. If snowbanks build up around the vehicle while the hybrid system is operating, exhaust gases may collect and enter the vehi- cle. this may lead to death or a serious health hazard.

n Exhaust gases

Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard.

If the vehicle is in a poorly ventilated area, stop the hybrid system. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

l The exhaust should be checked occasionally. If there is a hole or crack cause by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.

126

PRIUS_U_(L/O_0802)

2-1. Driving procedures

CAUTION

n When taking a nap in the vehicle

Always turn the hybrid system off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to hybrid system overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

n When braking the vehicle

l When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle. If the power brake assist function does not operate, do not follow other vehicles closely and avoid downhill or sharp turns that require braking. In this case, braking is still possible, but it will require more force on the pedal than usual. Braking distance may also increase.

l Do not pump the brake pedal if the hybrid system stalls.

Each push on the pedal uses up your reserved brake fluid pressure.

l The brake system consists of 3 individual hydraulic systems: if one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and braking distance becomes longer. Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.

127

PRIUS_U_(L/O_0802)

2-1. Driving procedures

NOTICE

n While driving the vehicle

Do not use the accelerator pedal or depress accelerator and brake pedals together to hold the vehicle on a hill.

n When parking the vehicle

Always push the “P” position switch. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is accidentally depressed.

n Avoiding damage to vehicle parts

l Do not turn the steering wheel fully in either direction and hold it there for a

long time. Doing so may damage the power steering motor.

l When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

n If you hear a squealing or scraping noise (brake pad wear limit indica-

tors) Have your Toyota dealer check and replace the brake pads as soon as pos- sible. The rotor damage can result if the pads are not replaced when needed. Front brake only: Moderate levels of the brake pad and disc wear allow enhanced front braking power. As a result, the discs may wear more quickly than conventional brake discs. Therefore, when replacing the brake pads, Toyota recommends that you also have the thickness of the discs measured. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or that of the brake discs are exceeded.

128

PRIUS_U_(L/O_0802)

2-1. Driving procedures

NOTICE

n If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually press the brake pedal to slow down the vehicle. It may be difficult to control your vehicle. l The vehicle will make abnormal sounds. l The vehicle will behave abnormally. Replace a flat tire with a new one. (→P. 441)

n When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle. l Engine stalling l Short in electrical components l Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. l Brake function l Changes in quantity and quality of engine oil, transmission fluid for the

hybrid system, etc.

l Lubricant condition for the bearings and suspension joints (where possi-

ble) and the function of all joints, bearings, etc.

129

PRIUS_U_(L/O_0802)

2-1. Driving procedures Power (ignition) switch

Modes can be switched by pressing the “POWER” switch when car- rying the electronic key on your person. (The hybrid system can be started in any mode by operating the switch at the same time as depressing the brake pedal.) n Changing power (ignition) switch mode

OFF mode ACCESSORY mode Some electrical components such as the audio system can be used. ON mode All electrical components can be used. *: The power

cannot be switched to OFF unless the shift lever is in “P”.

POWER

POWER

POWER

ITY21P001

130

PRIUS_U_(L/O_0802)

2-1. Driving procedures

n Starting the hybrid system (vehicle with smart key system) STEP 1

Check that the parking brake is set. Turn off unnecessary lights and accessories. Check that the shift position is set in “P”. Sit in the driver’s seat and firmly depress the brake pedal.

STEP 2

STEP 3

STEP 4

STEP 5

POWER

READY

Press the “POWER” switch.

few seconds,

After a the “READY” light will flash and come on with a beep sound. The vehicle can move when the “READY” light is on, even if the hybrid system is stopped.

ITY21P002

131

PRIUS_U_(L/O_0802)

2-1. Driving procedures

n Starting the hybrid system (vehicle without smart key sys-

tem) STEP 1

STEP 2

STEP 3

STEP 4

Check that the parking brake is set. Turn off unnecessary lights and accessories. Check that the shift position is set in “P”.

Insert the key into the key slot and firmly with the brake pedal depressed.

ITY21P009

132

PRIUS_U_(L/O_0802)

STEP 5

POWER

READY

2-1. Driving procedures

Press the “POWER” switch.

few seconds,

the After a “READY” light will flash and come on with a beep sound. The vehicle can move when the “READY” light is on, even if the hybrid system is stopped.

ITY21P002

133

PRIUS_U_(L/O_0802)

2-1. Driving procedures

n If the hybrid system does not start

The hybrid system immobilizer system may not have been deactivated. (→P. 81)

n If the “READY” light does not come on

If the “READY” light does not come on when you press the power switch with the shift lever in “P” and the brake pedal pressed, contact your Toyota dealer immediately.

n When the “POWER” switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toy- ota dealer immediately.

n Auto power OFF function

The “POWER” switch will automatically turn OFF when left in ACCESSORY mode for 1 hour or more.

n Electronic key battery depletion

→P. 44

n When the electronic key battery is discharged

→P. 396

n Conditions affecting operation

→P. 42

n Leak detection pump

Several hours after the engine is turned off, you may hear a sound coming from underneath the luggage compartment for several minutes. This is normal operation and does not indicate a malfunction.

134

PRIUS_U_(L/O_0802)

2

2-1. Driving procedures

CAUTION

n When starting the hybrid system

Always start the hybrid system while sitting in the driver’s seat. Do not press the accelerator pedal while starting the hybrid system under any circum- stances. Doing so may cause an accident resulting in death or serious injury.

n Stopping the hybrid system in an emergency

If you want to stop the hybrid system in an emergency while driving the vehi- cle, push and hold the “POWER” switch for more than 3 seconds. However, do not touch the “POWER” switch while driving except in an emer- gency. If the hybrid system stops while the vehicle is being driven, this could lead to an unexpected accident.

NOTICE

n To prevent 12 volt battery discharge

Do not leave the “POWER” switch in ACCESSORY or ON mode for long periods if the hybrid system is not running.

n When starting the hybrid system

l Do not race the hybrid system.

If the hybrid system becomes difficult to start or stalls frequently, have the hybrid system checked immediately.

135

PRIUS_U_(L/O_0802)

2-1. Driving procedures Transmission

Select a shift position appropriate for the driving conditions. n Shifting the shift lever

You can operate the shift lever only in “D”. Keep the shift lever in “N” for a while after you shift it to that position. The shift lever always returns to this original position after shifting operation.

ITY21P003

136

PRIUS_U_(L/O_0802)

2-1. Driving procedures

n Shift position uses

Shift position

Function

Parking the vehicle or starting the hybrid system

Reversing Neutral

Normal driving

Engine braking position*

*: Shown only while in “D” position.

Changing shift ranges in “P” position

With the brake pedal pressed down, push the “P” position switch. The “P” position is displayed on the instrument cluster, and the indicator on the “P” position switch comes on.

You can only shift to other posi- tion from “P” when the brake pedal is depressed.

ITY21P004

137

PRIUS_U_(L/O_0802)

2-1. Driving procedures

n Using engine brake

To use the engine braking, shift the shift lever to “B” position. l During high speed driving, you may feel that deceleration by engine brak-

ing is less than that of a typical vehicle.

l Do not continue normal driving with the transmission in “B” for a long

time. This may cause decreased fuel economy. To prevent this, use “D” for normal driving.

n Reverse warning buzzer

When shifting into “R”, a buzzer will sound to inform the driver that the shift lever is in “R”.

n If the system malfunctions

The following conditions, there is some problem in the system. Immediately stop the vehicle in a safe place and contact your Toyota dealer. l The indicator on the “P” position switch flashes. However, this does not indicate a malfunction unless a warning message appears in the touch screen.

l All frames of shift position indicators in the instrument cluster flash. l The parking system error message appears on the touch screen. l The instrument cluster and touch screen does not come on when the

“POWER” switch is in ON mode.

138

PRIUS_U_(L/O_0802)

2-1. Driving procedures

n Alarms

The following table describes circumstances and correction procedures when only alarms are sound.

Alarm

Situation

The driver attempts to shift out of the “P” position with- out pressing the brake pedal.

The “P” position switch is pressed while the vehicle is moving. The driver attempts to shift to the “R” position while the vehicle is in forward motion. The driver attempts to shift to the “D” position while the vehicle is in rearward motion. The driver attempts to select the “B” position while in a shift position other than “D” and “P”. The driver attempts to select the “B” position while in the “P” position.

If the driver’s door is opened when the transmis- sion is in “N”, “D” or “B”.

Interior alarm sounds once

Interior alarm beep sounds and warning message*

*: Follow the warning message displayed.

PRIUS_U_(L/O_0802)

Correction procedure The transmission will not move out of the “P” position, so press the brake pedal before attempting to shift again.

The transmission will automatically be set to the “N” position, so select the appropriate position.

The transmission will not move out of the “P” position.

Push the “P” position switch.

139

2-1. Driving procedures Turn signal lever (Type A)

Left turn Right turn Move and hold the lever partway to signal a lane change The left hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change The right hand signal will flash until you release the lever.

n Turn signals can be operated when The “POWER” switch is in ON mode.

n If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

140

PRIUS_U_(L/O_0802)

2

2-1. Driving procedures Turn signal lever (Type B)

Left turn Right turn Move and hold the lever partway to signal a lane change The left hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change The right hand signal will flash until you release the lever.

n Turn signals can be operated when The “POWER” switch is in ON mode.

n If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

141

PRIUS_U_(L/O_0802)

2-1. Driving procedures Parking brake

Sets the parking brake* (Depressing the pedal again releases the parking brake.)

*: Fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot.

U.S.A.

Canada

ITY21P007

NOTICE

n Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

n When parking the vehicle

Before you leave the vehicle, set the parking brake, push the “P” position switch and make sure that the vehicle does not move.

142

PRIUS_U_(L/O_0802)

2-2. Instrument cluster Gauges and meters

The following gauges and meters illuminate when the “POWER” switch is in ON mode.

Shift position indicator Displays the shift position Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Odometer Displays the total distance the vehicle has been driven. Trip meter Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently.

143

PRIUS_U_(L/O_0802)

2-2. Instrument cluster

Odometer/trip meter and trip meter reset button

Odometer Trip meter A* Trip meter B*

*: Pushing and holding the but-

ton will reset the trip meter.

MPH or km/h button

The speed units can be selected MPH or km/h.

MA VO

km/h MPH

km/h MPH

ITY22P003

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker

144

PRIUS_U_(L/O_0802)

2-2. Instrument cluster

NOTICE

n To prevent damage to the hybrid system and its components

The hybrid system may be overheating if the high coolant temperature warn- ing light is displayed on the touch screen. In this case, immediately stop the vehicle in a safe place. Check the hybrid system after it has cooled com- pletely. (→P. 456)

145

PRIUS_U_(L/O_0802)

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster

Touch screen (Type A)

ITY22P006

146

PRIUS_U_(L/O_0802)

2-2. Instrument cluster

Touch screen (Type B)

ITY22P007

147

PRIUS_U_(L/O_0802)

2-2. Instrument cluster

n Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Turn signal indicator (→P. 140)

Headlight high beam indicator (→P. 150)

Headlight indicator (→P. 150)

Tail light indicator (→P. 150)

(U.S.A.)

(Canada)

Shift position and shift range indicators (→P. 136)

Cruise control indicator (→P. 164)

Slip indicator (→P. 170)

ON

SRS airbag on-off indi- cator (→P. 101)

Recirculate mode indi- cator (→P. 205, 212) Automatic air condi- tioner indicator (→P. 202, 209)

Windshield air flow indi- cator (→P. 205, 212)

Rear window and out- side rear view mirror defoggers indicator (→P. 217) Driving ready indicator (→P. 130) Immobilizer / Theft deterrent system indica- tor (→P. 81, 84)

148

PRIUS_U_(L/O_0802)

2-2. Instrument cluster

n Warning lights

Warning lights inform the driver of malfunctions in the indicated vehicle’s systems. (→P. 426)

(U.S.A.)

(U.S.A.)

red

(Canada)

yellow

(if equipped)

(U.S.A.)

(Canada)

(if equipped) *:These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is started is on, or after a few seconds. There may be a malfunction in a system if the lights do not come on, or turn off. Have the vehicle inspected by your Toyota dealer.

CAUTION

n If a safety system warning light does not come on

Should a safety system light such as ABS and the SRS airbag warning light not come on when you start the hybrid system, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

149

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers Headlight switch (Type A)

The headlights can be operated manually or automatically.

U.S.A.

Canada

AU TO

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and all the lights listed above turn on and off auto- matically. (When the “POWER” switch is in ON mode.)

(if equipped)

ITY23P001

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release to turn them off. You can flash the high beams with the headlights on or off.

150

PRIUS_U_(L/O_0802)

2

2-3. Operating the lights and windshield wipers

n Daytime running light system (if equipped)

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the hybrid system is started and the parking brake is released. Daytime running lights are not designed for use at night.

n Headlight control sensor (if equipped)

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight con- trol system to malfunction.

interferes with

n Automatic light off system

Opening the driver’s door with the “POWER” switch in ACCESSORY mode or OFF will turn the headlights and tail lights off. To turn the lights on again, switch to ON mode, or turn the light switch “OFF” once and then back to the

position.

or

n Automatic headlight leveling system (Vehicle with discharge head-

lights) The level of the headlights is automatically adjusted according to the number of passengers and the loading condition of the vehicle to ensure that the headlights do not interfere with other road users.

n If the

indicator flashes...

It may indicate a malfunction in the system. Contact your Toyota dealer.

n Customization

Settings (e.g. light sensor sensitivity) can be changed. (→P. 488)

151

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers

NOTICE

n To prevent 12 volt battery discharge

Do not leave the lights on longer than necessary if the hybrid system is not running.

152

PRIUS_U_(L/O_0802)

2

2-3. Operating the lights and windshield wipers Headlight switch (Type B)

The headlights can be operated manually or automatically.

U.S.A.

Canada

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and all the lights listed above turn on and off auto- matically. (When the “POWER” switch is in ON mode.)

(if equipped)

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release to turn them off. You can flash the high beams with the headlights on or off.

153

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers

n Daytime running light system (if equipped)

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the hybrid system is started and the parking brake is released. Daytime running lights are not designed for use at night.

n Headlight control sensor (if equipped)

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight con- trol system to malfunction.

interferes with

n Automatic light off system

Opening the driver’s door with the “POWER” switch in ACCESSORY mode or OFF will turn the headlights and tail lights off. To turn the lights on again, switch to ON mode, or turn the light switch “OFF” once and then back to the

position.

or

n Automatic headlight leveling system (Vehicle with discharge head-

lights) The level of the headlights is automatically adjusted according to the number of passengers and the loading condition of the vehicle to ensure that the headlights do not interfere with other road users.

n If the

indicator flashes...

It may indicate a malfunction in the system. Contact your Toyota dealer.

n Customization

Settings (e.g. light sensor sensitivity) can be changed. (→P. 488)

154

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers

NOTICE

n To prevent 12 volt battery discharge

Do not leave the lights on longer than necessary if the hybrid system is not running.

155

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers Fog light switch (if equipped)

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.

Type A

OFF ON

ITY23P004

156

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers

Type B

157

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers Windshield wipers and washer (Type A)

Wiper intervals can be adjusted for intermittent operation (when “INT” is selected).

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

Wash/wipe operation

Wipers operate automatically.

ITY23P005

ITY23P007

158

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers

n The windshield wiper and washer can be operated when

The “POWER” switch is in ON mode.

n Intermittent windshield wiper interval (“INT”) mode

Intermittent windshield wiper interval adjustment (increase) Intermittent windshield wiper interval adjustment (decrease)

ITY23P008

n If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

n When the windshield is dry

Do not use the wipers, as they may damage the windshield.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. n When a nozzle becomes block

Do not try to clear it with a pin or other object. The nozzle will be damaged.

159

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers Windshield wipers and washer (Type B)

Wiper intervals can be adjusted for intermittent operation (when

is selected).

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

Wash/wipe operation

Wipers operate automatically.

ITY23P012

ITY23P013

160

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers

n The windshield wiper and washer can be operated when

The “POWER” switch is in ON mode.

n Intermittent windshield wiper interval mode

Intermittent windshield wiper interval adjustment (decrease) Intermittent windshield wiper interval adjustment (increase)

ITY23P014

n If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

n When the windshield is dry

Do not use the wipers, as they may damage the windshield.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. n When a nozzle becomes block

Do not try to clear it with a pin or other object. The nozzle will be damaged.

161

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers Rear window wiper and washer (Type A)

Intermittent window wiper operation Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion

ITY23P006

n The rear window wiper and washer can be operated when

The “POWER” switch is in ON mode.

NOTICE

n When the rear window is dry

Do not use the wipers, as they may damage the rear window.

162

PRIUS_U_(L/O_0802)

2-3. Operating the lights and windshield wipers Rear window wiper and washer (Type B)

Intermittent window wiper operation Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion