2008 Toyota Prius Owners Manual

ITY23P015

n The rear window wiper and washer can be operated when

The “POWER” switch is in ON mode.

NOTICE

n When the rear window is dry

Do not use the wipers, as they may damage the rear window.

163

PRIUS_U_(L/O_0802)

2-4. Using other driving systems Cruise control (if equipped)

Use the cruise control to maintain a set speed without using the accelerator. n Set the vehicle speed STEP 1

Turn the “ON-OFF” button ON. Push the button once more to deactivate the cruise control.

STEP 2

Accelerate or decelerate to the desired speed and press the lever down to set the cruise control speed.

n Adjusting the speed setting

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. the set Fine adjustment of speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pressing the lever up or down and releasing it.

164

PRIUS_U_(L/O_0802)

2

2-4. Using other driving systems

n Canceling and resuming regular acceleration

the brake pedal

Cancel Push the lever towards you to cancel cruise control. The setting is also canceled when is depressed. Resume To resume cruise control and return to the set speed, push the lever up.

n Cruise control can be set when

l The shift lever is in the “D” range. l Vehicle speed is between approximately 25 mph (40 km/h) and 125 mph

(200 km/h). n Accelerating

The vehicle can be accelerated normally. After acceleration, the set speed resumes.

n Automatic cruise control cancelation

The set speed is automatically canceled in any of the following situations. l Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed

l Actual vehicle speed is below 25 mph (40 km/h) l Enhanced VSC is activated

n If the cruise control indicator light flashes

Turn the “ON-OFF” button off once, and then reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

165

PRIUS_U_(L/O_0802)

2-4. Using other driving systems

CAUTION

n To avoid operating the cruise control by mistake

Keep the “ON-OFF” button off when not in use.

n Situations unsuitable for cruise control

In heavy traffic

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause seri- ous or fatal accident. l On roads with sharp bends l On slippery roads, such as those covered with rain, ice or snow l On winding roads l On steep hills

Vehicle speed may exceed the set speed when driving down a steep hill.

166

PRIUS_U_(L/O_0802)

2-4. Using other driving systems Rear view monitor system

The rear view monitor system assists the driver by displaying an image of the view behind the vehicle while reversing. The image is displayed in reverse on the screen. This allows the image to appear in the same manner as that of the rear view mirror.

Rear view image is displayed when the shift lever is in “R”.

If you move the lever out of “R”, the screen returns to the previous one.

ITY24P005

n Displayed area

the bumper or under

The area covered by the camera is lim- ited. Objects which are close to either corner of the bumper cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.

167

ITY24P006

Corner of bumper

ITY24P007

PRIUS_U_(L/O_0802)

2-4. Using other driving systems

n Rear view monitor system camera

In the following cases, it may be difficult to see the images on the screen, even when the system is functioning correctly. • In the dark (e.g. at night). • If the temperature near the lens is

extremely high or low.

• If water droplets get on the camera, or when humidity is high (e.g. when it rains).

• If foreign matter (e.g. snow or mud)

get on the camera lens.

• If the sun or headlights are shining

directly into the camera lens.

If a bright light (for example, sunlight reflected off the vehicle body) is picked up by the camera, a smear effect* pecu- liar to the camera may occur. *:Smear effect—A phenomenon that occurs when a bright light (for example, sunlight reflected off the vehicle body) is picked up by the camera; when trans- mitted by the camera, the light source appears to have a vertical streak above and below it.

n Smear effect

ITY24P008

ITY24P009

168

PRIUS_U_(L/O_0802)

2-4. Using other driving systems

CAUTION

n When using the rear view monitor system, observe these precautions

to avoid an accident that could result in death or serious injuries. l Never depend solely on the monitor system when reversing. l Always check visually and with the mirrors to confirm your intended path is

clear.

l Depicted distances between objects and flat surfaces differ from actual

distances.

l Do not use the system if the back door is open.

n Conditions which may affect the rear view monitor system

If the back of the vehicle is hit, the camera’s position and mounting angle may change. Contact your Toyota dealer.

l Rapid temperature changes, such as when hot water is poured on the

vehicle in cold weather, may cause the system to function abnormally. If the camera lens is dirty, it cannot transmit a clear image. Rinse with water and wipe with a soft cloth. If extremely dirty, wash with a mild cleanser and rinse.

l The displayed image may be darker and moving images may be slightly

distorted when the system is cold.

169

PRIUS_U_(L/O_0802)

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. n ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

n Brake Assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

n Enhanced VSC (Vehicle Stability Control) (If equipped)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

n EPS (Electric Power Steering)

Employs an electric motor to reduce the amount of effort needed to turn the steering wheel.

When the Enhanced VSC is operating

If the vehicle is in danger of slip- ping or the front wheels spin, the indicator flashes to indicate that the Enhanced VSC have been engaged.

A buzzer (intermittent) sounds to indicate that Enhanced VSC is operating. The slip indicator light flashes as well when ABS is operating.

ITY24P010

170

PRIUS_U_(L/O_0802)

2

2-4. Using other driving systems

n Sounds and vibrations caused by the ABS, BA and Enhanced VSC

l A sound may be heard from the hybrid system compartment when the hybrid system is started or just after the vehicle begins to move. This sound does not indicate that a malfunction has occurred in any of these systems.

l Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.

n Reduced effectiveness of EPS

The effectiveness of EPS is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the hybrid system OFF. The system should return to normal within 10 minutes.

171

PRIUS_U_(L/O_0802)

2-4. Using other driving systems

CAUTION

n The ABS does not operate effectively when

l The limits of tire gripping performance have been exceeded. l The vehicle hydroplanes while driving at high speed on the wet or slick

road.

n Stopping distance when the ABS is operating on the wet or slick roads The ABS is not designed to shorten the vehicle’s stopping distance. Always maintain a sufficient distance from the vehicle in front of you in the following situations. l When driving on dirt, gravel or snow-covered roads l When driving with tire chains l When driving over bumps in the road l When driving over roads with potholes or roads with uneven pavement

n When the Enhanced VSC is activated

The slip indicator light flashes and a warning buzzer sounds. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes and a buzzer sounds.

n Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the speci- fied tire pressure level. The ABS and Enhanced VSC will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

172

PRIUS_U_(L/O_0802)

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load.

l Stow cargo and luggage in the back door whenever possible.

Be sure all items are secured in place.

l Be careful to keep the vehicle level. Placing the weight as far

forward as possible helps maintain vehicle balance.

l For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit— (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehi- cle’s placard.

(2) Determine the combined weight of the driver and passengers

that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and

luggage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs. (1400 - 750 (5
× 150) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being

loaded on the vehicle. That weight may not safely exceed the available cargo and lug- gage load capacity calculated in Step 4.

173

PRIUS_U_(L/O_0802)

2-5. Driving information

(6)

If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 176) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 815 lb. (370
kg), the available amount of cargo and luggage load capacity will be as follows: 810 lb. — 366 lb. = 444 lb. (365 kg — 166 kg = 199 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

444 lb. — 388 lb. = 56 lb. (199 kg — 176 kg = 23 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load equaling the combined weight of the occupants who got on later, by an amount. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

174

PRIUS_U_(L/O_0802)

2-5. Driving information

CAUTION

n Storage precautions

l Do not place anything on the package tray behind the rear seatback. Such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

l Do not drive with objects on top of the instrument panel.

They may interfere with the driver’s field of view or move during sharp acceleration or turning, thus impairing the driver’s control of the vehi- cle. In an accident they may injure the vehicle occupants.

l Secure all items in the occupant compartment, as they may shift and

injure someone during an accident or sudden braking.

n Weight of the load

Improper loading may cause deterioration of steering or braking con- trol resulting in an accident which may cause death or serious injury.

l Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

l Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

175

PRIUS_U_(L/O_0802)

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. n Total load capacity: 810 lb. (365 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

n Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. Even if the number of occupants are within the seating capacity, do not exceed the total load capacity.

n Towing capacity

Toyota does not recommend towing a trailer with your vehicle.

n Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

n Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 388)

CAUTION

n Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

176

PRIUS_U_(L/O_0802)

2

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. n Pre-winter preparations

l Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

l Have a service technician inspect the level and specific grav-

ity of 12 volt battery electrolyte.

l Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires.

177

PRIUS_U_(L/O_0802)

2-5. Driving information

n Before driving the vehicle

Perform the following according to the driving conditions. l Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. l To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

l Remove any ice that has accumulated on the vehicle chassis. l Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

n When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

n When parking the vehicle

Park the vehicle and Push the “P” position switch without setting the parking brake. The parking brake may freeze up, preventing it from being released.

178

PRIUS_U_(L/O_0802)

2-5. Driving information

Regulations on the use of snow chains

l Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

l Use SAE Class “S” type radial tire chains, with the exception of

radial cable chains or V-bar type chains. • • Refer to the explanation that comes with the tire chains for

Install the chains on the front tires.

installation instructions.

l Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

n Snow chain installation

Observe the following precautions when installing and removing chains.

Install and remove tire chains in a safe location. Install tire chains on the front tires. Install tire chains following the instructions provided in the accompanying instructions.

CAUTION

n Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. l Use tires of the size specified for your vehicle. l Maintain the specified level of tire inflation pressure. l Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

l Snow tires should be installed on all wheels.

179

PRIUS_U_(L/O_0802)

2-5. Driving information

CAUTION

n Driving with snow chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. l Do not drive in excess of the speed limit specified for the tire chains being

used, or 30 mph (50 km/h), whichever is lower.

l Avoid driving on bumpy road surfaces or over potholes. l Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

l Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

n Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

n Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

180

PRIUS_U_(L/O_0802)

2-5. Driving information Trailer towing

Toyota does not recommend towing a trailer with your vehicle. Toy- ota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for the use of tow hitch mounted carriers.

ITY25P001

181

PRIUS_U_(L/O_0802)

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

ITY25P002

NOTICE

n To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

182

PRIUS_U_(L/O_0802)

2-5. Driving information

183

PRIUS_U_(L/O_0802)

v3-1.Using the touch screen Touch screen

By touching the screen with your finger, you can control the audio system and air-conditioning, adjust the screen display etc.

Vehicles with navigation system

Vehicles without navigation system (Type A)

186

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

Vehicles without navigation system (Type B)

The “Information” screen shown in the above illustration is displayed when

the

is pressed.

Page

Switches

“CLIMATE” “AUDIO” “INFO” (Displaying the “Informa- tion” screen) “DISP” (Adjusting the display) Trip Information. (Displaying the “Trip Information” screen)

P. 201, 208
P. 219, 222

P. 186

P. 192, 197

P. 27

Maintenance

Telephone

Calendar

Language Screen Setting

Navigation System Owner’s Man- ual P. 277
Navigation System Owner’s Man- ual P. 191, 196
P. 194, 199

187

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

The initial screen

Vehicles with navigation system and vehicles without navigation system (Type A)

If the “POWER” switch is set to ACCESSORY or ON mode, the initializing screen will be dis- played for a few seconds as the system starts up.

Vehicles without navigation system (Type B)

188

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

Outside temperature display

The outside temperature is shown ranging from -22 °F (-30 °C) up to 122 °F (50 °C) at the upper right of the energy consumption or energy monitor screen or the upper left/right of the air conditioner screen.

Vehicles with navigation system and vehicles without navigation system (Type A)

189

Vehicles without navigation system (Type B)

MPGMPG

ITY31P017

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

n To avoid damaging the touch screen

l Touch the screen lightly with your finger. If there is no response, remove

your finger from the screen and try again.

l Remove any dirt on the screen by wiping with a soft cloth. Do not use

detergent.

n When using the touch screen

If the screen is cold, the display may be dark, or the system may seem to be operating slightly slower than normal.

l The screen may seem dark and hard to see when viewed through sun- glasses. Change your angle of viewing, adjust the display on he “Display” screen or remove your sunglasses.

n When the outside temperature drops below 37 °F (3 °C).

Also except the screen where outside temperature is displayed, outside tem- * are displayed in the upper portion of the screen for a perature and few seconds. *:

may not be displayed depending on the display type.

190

PRIUS_U_(L/O_0802)

3-1. Using the touch screen Setting the touch screen (Vehicles with AUX adapter)

You can change the touch screen to your desired settings.

Language settings

The language used for all voice guidance, messages and touch screen switches may be changed.

STEP 1

Press

STEP 2

Touch

on the “Information” screen.

STEP 3

Select the desired language.

STEP 4

Touch

Turning off the beep sound (if equipped)

The beep that sounds when a touch screen button is touched can be turned off. STEP 1

Press

191

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

STEP 2

Touch

Adjusting the display

STEP 1

STEP 2

Press Adjust the display as desired using If you do not touch the screen for 20 seconds, the system will return to the previous screen.

and

Contrast Brightness

Weaker Darker

Stronger Brighter

192

PRIUS_U_(L/O_0802)

n “Day Mode”

3-1. Using the touch screen

When the headlights are turned on, the screen dims. However the screen can be switched to “Day Mode”.

The screen will stay in “Day Mode” when the headlights are turned on until

is touched again.

If the instrument panel light control is set to “MAX”, “Day Mode” is not dis- played.

n To turn off the picture display

is touched, the screen display is turned off, and guidance is by

If voice only.

193

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

Screen settings

STEP 1

Press

STEP 2

Touch

on the “Information” screen. The following screen settings can be changed.

Automatic transition 20 seconds after air-conditioning or audio system use, the system will return the display to the previ- ous screen. Switch color You can select the switch color. Personal data deletion The following personal data is deleted: • User selection settings • Phone book data • Dialed numbers and received

calls

• Speed dial • Bluetooth® phone data • Security code • Maintenance conditions* • Maintenance information “off”

setting*

• Memory points* • Areas to avoid* • Previous points* • Route trace* *:If

equipped

the navigation system

is

194

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

n Setting automatic transition STEP 1

Touch

or

on the “Screen Setting” screen.

STEP 2

Press

n Setting the switch color or STEP 1

Touch

STEP 2

Press

n To delete personal data STEP 1

Touch the

STEP 2

on the “Screen Setting” screen.

on the “Screen Setting” screen.

Touch

Check carefully beforehand, as data cannot be retrieved once ini- tialized.

ITY31P011

n When deleting personal data

Data can only be deleted when the vehicle is stopped.

n When selling the vehicle

Be sure to initialize both the call history and personal data. (→P. 194)

n If you touch the

The display returns to the previous screen.

195

PRIUS_U_(L/O_0802)

3-1. Using the touch screen Setting the touch screen (Vehicles without AUX adapter)

You can change the touch screen to your desired settings.

Language settings

The language used for all voice guidance, messages and touch screen switches may be changed.

STEP 1

Press

STEP 2

Touch

on the “Information” screen.

STEP 3

Select the desired language.

STEP 4

Touch

196

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

Adjusting the display

STEP 1

Press

STEP 2

Adjust the display as desired using If you do not touch the screen for 20 seconds, the system will return to the previous screen.

and

Contrast Brightness

ITY31P013

Weaker Darker

Stronger Brighter

197

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

n “Day Mode”

When the headlights are turned on, the screen dims. However the screen can be switched to “Day Mode”.

The screen will stay in “Day Mode” when the headlights are turned on until

ITY31P014

is touched again.

If the instrument panel light control is set to “MAX”, “Day Mode” is not dis- played.

n To turn off the picture display

is touched, the screen display is turned off, and guidance is by

If voice only.

198

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

Screen settings

STEP 1

Press

STEP 2

Touch

on the “Information” screen. The following screen settings can be changed.

Automatic transition 20 seconds after air-conditioning or audio system use, the system will return the display to the previ- ous screen. Switch color You can select the switch color.

199

PRIUS_U_(L/O_0802)

3-1. Using the touch screen

n Setting automatic transition STEP 1

or

Touch Press

STEP 2

n Setting the switch color STEP 1

Touch screen. Press

STEP 2

on the “Screen Setting” screen.

or

on the “Screen Setting”

200

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger Automatic air conditioning system (Vehicles with AUX adapter)

Airflow and outlets are automatically adjusted according to the tem- perature setting. Press

to display the air conditioning operation screen.

Passenger compartment temperature display

Outside temperature display

Off

Air conditioning operation screen display button

Temperature control Airflow display Fan speed display

Automatic mode

Air conditioning ON/OFF switch

Outside air or recirculated mode

Windshield defogger

The above illustration is for a vehicle equipped with the navigation

ITY32P001

system. The position of equipped with the navigation system.

may differ slightly for vehicles not

201

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

Using the automatic mode

STEP 1

Press

indicator located in the instrument panel.

STEP 3
STEP 2

The air conditioning system will begin to operate. Air outlets and fan, and automatically switches between outside air and recirculated air modes are automatically adjusted according to the temperature setting. Press ∧ to increase the temperature and ∨ to decrease the temperature. The temperature for the driver and passenger seats can be set sep- arately.

Adjusting the settings

n Adjusting the temperature setting

Press ∧ to increase the temperature and ∨ to decrease the temper- ature.

202

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

n Adjusting the fan speed

Touch any switch of increase) on the operating screen. Press

to turn the fan off.

n Changing the air outlets

(decrease ↔

Touch any mode on the operat- ing screen.

Air flows to the upper body.

ITY32P002

ITY32P003

: In the beginning of the automatic air flow mode, air might be delivered.

Air flows to the upper body and feet.

ITY32P004

203

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

Air flows to the feet.

Air flows to the feet and the windshield defogger operates.

ITY32P005

ITY32P006

204

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

n Switching between outside air and recirculated air modes

Press

The mode switches between

(recycles air inside the vehicle) and (introduces air from outside the vehicle) modes each time the but-

ton is pressed. l When the system is switched to automatic mode, the air conditioning system operates automatically. However, recirculated air mode will be activated if it is selected manually. If the hybrid system us turned off in the outside air mode, the auto- matic control of the air intake is activated when the hybrid system is turned on again.

indicator will come on in the instrument cluster while the recircu-

lated air mode is selected.

Defogging the windshield

Press

The air conditioning system con- trol operates automatically.

indicator will come on in the instrument cluster while the windshield air flow mode is on.

ITY32P011

205

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Front outlets

Direct air flow to the left or right, up or down Turn the knob to open or close the vent

ITY32P008

n Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. l The system may switch automatically to recirculated mode when the

coolest temperature setting is selected in summer. Immediately after the switch is pressed, the fan may stop for a while until warm or cool air is ready to flow.

n Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

n Window defogger feature

Recirculated air mode may automatically switch to in situations where the windows need to be defogged.

n Outside temperature approaches 32°F (0°C).

(outside air) mode

The air conditioning system may not operate even when

is touched.

n 2-way air intake control

To improve fuel economy, OUTSIDE AIR mode control changes when the air intake selector is set in OUTSIDE AIR on the following conditions: l When the maximum heating is needed with the air flow in “Floor” or “Floor/Windshield”, fresh air flows in the upper compartment, while air is recirculated in the lower compartment.

l When cooling is needed, both fresh and recirculate modes turns on.

206

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

CAUTION

n To prevent the windshield from fogging up

Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

n To prevent 12 volt battery discharge

Do not leave the automatic air conditioning system on longer than necessary when the hybrid system is not running.

207

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger Automatic air conditioning system (Vehicles without AUX adapter)

Airflow and outlets are automatically adjusted according to the tem- perature setting. Press

to display the air conditioning operation screen.

Outside temperature display

Air conditioning ON/OFF switch

Passenger compartment temperature display

Air conditioning operation screen display button

Outside air or recirculated mode

CLIMATE

AUDIO

85 F

75

DISPLAY

Airflow display

Fan speed display

INFO

Temperature control

ODO TRIP

km/h MPH

Windshield defogger

Off

Automatic mode

The above illustration is for a vehicle equipped with the navigation

system. The position of equipped with the navigation system.

may differ slightly for vehicles not

ITY32P009

208

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

Using the automatic mode

STEP 1

Press

indicator located in the instrument panel.

STEP 2

The air conditioning system will begin to operate. Air outlets and fan, and automatically switches between outside air and recirculated air modes are automatically adjusted according to the temperature setting. Press ∧ to increase the temperature and ∨ to decrease the temperature. The temperature for the driver and passenger seats can be set sep- arately.

Adjusting the settings

n Adjusting the temperature setting

Press ∧ to increase the temperature and ∨ to decrease the temper- ature.

209

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

n Adjusting the fan speed

Touch any switch of increase) on the operating screen. Press

to turn the fan off.

n Changing the air outlets

(decrease ↔

Touch any mode on the operat- ing screen.

Air flows to the upper body.

ITY32P010

ITY32P003

: In the beginning of the automatic air flow mode, air might be delivered.

Air flows to the upper body and feet.

ITY32P004

210

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

Air flows to the feet.

ITY32P005

ITY32P006

Air flows to the feet and the windshield defogger operates.

211

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

n Switching between outside air and recirculated air modes

Press

The mode switches between

(recycles air inside the vehicle) and (introduces air from outside the vehicle) modes each time the but-

ton is pressed. l When the system is switched to automatic mode, the air conditioning system operates automatically. However, recirculated air mode will be activated if it is selected manually. If the hybrid system us turned off in the outside air mode, the auto- matic control of the air intake is activated when the hybrid system is turned on again.

indicator will come on in the instrument cluster while the recircu-

lated air mode is selected.

Defogging the windshield

Press

The air conditioning system con- trol operates automatically.

indicator will come on in the instrument cluster while the windshield air flow mode is on.

ITY32P007

212

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Front outlets

Direct air flow to the left or right, up or down Turn the knob to open or close the vent

ITY32P008

n Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. l The system may switch automatically to recirculated mode when the

coolest temperature setting is selected in summer. Immediately after the switch is pressed, the fan may stop for a while until warm or cool air is ready to flow.

n Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

n Window defogger feature

Recirculated air mode may automatically switch to in situations where the windows need to be defogged.

n Outside temperature approaches 32°F (0°C).

(outside air) mode

The air conditioning system may not operate even when

is touched.

n 2-way air intake control

To improve fuel economy, OUTSIDE AIR mode control changes when the air intake selector is set in OUTSIDE AIR on the following conditions: l When the maximum heating is needed with the air flow in “Floor” or “Floor/Windshield”, fresh air flows in the upper compartment, while air is recirculated in the lower compartment.

l When cooling is needed, both fresh and recirculate modes turns on.

213

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

CAUTION

n To prevent the windshield from fogging up

Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

n To prevent 12 volt battery discharge

Do not leave the automatic air conditioning system on longer than necessary when the hybrid system is not running.

214

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger Using the steering wheel climate remote control switches

Some air conditioning features can be controlled using the switches on the steering wheel.

ITY32P014

Automatic mode Temperature control Recirculated air mode Windshield defogger mode Rear window and outside rear view mirror defogger mode

Using the automatic mode

STEP 1

Press The air conditioning system will operate, and air outlets and fan speed will be set automatically. “AUTO” will be displayed on the multi-information display. (if equipped)

STEP 2

Press “∧” on decrease the temperature.

to increase the temperature and “∨” to

Adjusting the temperature setting

Press “∧” on the temperature.

to increase the temperature and “∨” to decrease

215

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger

Changing the recirculated air mode

Press

. (→P. 205, 212)

Using the windshield defogger mode

Press

. (→P. 205, 212)

Using the rear window and outside rear view mirror defogger mode

Press

. (→217)

216

PRIUS_U_(L/O_0802)

3-2. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers

These features are used to defog the rear window, and to remove raindrops, dew and frost from the outside rear view mirrors. (vehi- cles with mirror defoggers)

Type A

Type B

Press the button.

Press the button to turn on the rear window and outside rear view mirror defoggers. The defoggers will automatically turn off after approximately 15
minutes. Pressing the button again also turns the defoggers off.

indicator located in the

instrument panel.