2019 Toyota Corolla Owners Manual

played.

• When only a small amount of fuel is added to the tank, the display may

not be updated. When refueling, turn the engine switch off. If the vehicle is refueled with- out turning the engine switch off, the display may not be updated.

● Elapsed time (after reset*2/after start)*1

Displays the elapsed time since the function was reset and the engine was started, respectively

● Eco Driving Indicator Zone Display (vehicles with a continuously

variable transmission) P. 100

● LDA (Lane Departure Alert with steering control) vehicle sway

warning P. 227

● Display off

A blank screen is displayed

*1: Can be registered to Drive information 1 or 2. (P. 93) *2: Resetting procedures:

• Select a function to be reset using the meter control switch and then

press and hold to reset.

• If there is more than one function that can be reset, check boxes will be

displayed next to those functions.

COROLLA_TMMMS_TMMC_U

2. Instrument cluster

93

Settings display ■ Changing the settings

using the meter control switch.

Select Select an item and then set it with the center button.

■ Customizable items

● LDA (Lane Departure Alert with steering control)

P. 226

● LDA (Lane Departure Alert with steering control) vehicle sway

warning P. 227

● PCS (Pre-Collision System)

P. 214

● Language

Select to change the language displayed on the multi-information display.

● Units

Select to change the unit of measure displayed on the multi-infor- mation display.

● Drive information 1/Drive information 2

Select to select up to 2 items that will be displayed on a Drive information screen.

● Eco driving indicator light

Select to activate/deactivate the Eco Driving Indicator Light. (P. 99)

● Pop-up display

Select to set the following pop-up displays, which may appear in some situations, on/off. • Route guidance display of the navigation system-linked sys-

tem (if equipped)

• Incoming call display of the hands-free phone system

● Accent color

Select to change the accent colors on the screen, such as the cursor color.

COROLLA_TMMMS_TMMC_U

94

2. Instrument cluster

● Maintenance system (U.S.A.)

Select to reset the message after the required maintenance is performed. (P. 415)

● Initialization

Registered or changed meter settings will be deleted or returned to their default setting.

■Pop-up display

In some situations, such as when a switch operation is performed, a pop-up display, such as the operating dynamic radar cruise control switch, will be temporarily displayed on the multi-information display. The pop-up display function can be set on/off.

■Setting display automatic cancelation

In the following situations, a setting display in which the settings can be changed through the meter control switches will automatically be turned off. ●When a warning message appears while the setting display is displayed ●When the vehicle begins to move while the setting display is displayed

■Liquid crystal display

Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem continuing to use the display.

COROLLA_TMMMS_TMMC_U

2

2. Instrument cluster

95

WARNING

■The information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed. For example, there is a lag between the driver’s shifting and the new gear number appearing on the display. This lag could cause the driver to down- shift again, causing rapid and excessive engine braking and possibly an accident resulting in death or injury.

■Cautions during setting up the display

As the engine needs to be running during setting up the display, ensure that the vehicle is parked in a place with adequate ventilation. In a closed area such as a garage, exhaust gases including harmful carbon monoxide (CO) may collect and enter the vehicle. This may lead to death or a serious health hazard.

NOTICE

■During setting up the display

To prevent battery discharge, ensure that the engine is running while setting up the display features.

COROLLA_TMMMS_TMMC_U

96

2. Instrument cluster

Fuel consumption information Fuel consumption information can be displayed on Entune Audio, Entune Audio Plus and/or Entune Premium Audio.

Entune Audio, Entune Audio Plus or Entune Premium Audio

Trip information  Entune Audio Press the “CAR” button.

If the “Past Record” screen is dis- played, select “Trip Information”.

 Entune Audio Plus or Entune Premium Audio

Press the “APPS” button. Touch “Eco” on screen. If the “Past Record” screen is dis- played, select “Trip Information”.

the “Apps”

COROLLA_TMMMS_TMMC_U

fuel consumption

Average vehicle speed Elapsed time Range Previous per minute Current fuel consumption Reset data “Past Record” screen appears

information

trip

the

2. Instrument cluster

97

Vehicles without a smart key system: Average fuel consumption for the past 15 minutes is divided by color into past averages and averages attained since the engine switch was last turned to the “ON” position. Use the displayed average fuel con- sumption as a reference. Vehicles with a smart key system: Average fuel consumption for the past 15 minutes is divided by color into past averages and averages attained since the engine switch was last turned to IGNITION ON mode. Use the displayed average fuel consumption as a reference.

This image is an example only.

COROLLA_TMMMS_TMMC_U

98

2. Instrument cluster

■ Past record

 Entune Audio Press the “CAR” button.

If the “Trip Information” screen is displayed, select “Past Record”.

 Entune Audio Plus or Entune Premium Audio

Press the “APPS” button. Touch “Eco” on the “Apps” screen. If the “Trip Information” screen is displayed, select “Past Record”.

fuel economy

Previous record Current fuel economy Best recorded fuel econ- omy Update data Reset the past record data “Trip Information” screen appears Average recorded fuel economy

the past record

These images are examples only, and may vary slightly from actual conditions.

■Resetting the data

Selecting “Clear” on the “Trip Information” screen will reset the consumption data. Selecting “Clear” on the “Past Record” screen will reset the past record data.

■Updating the past record data

Selecting “Update” on the “Past Record” screen will update the past record data.

■Cruising range

Displays the estimated maximum distance that can be driven with the quan- tity of fuel remaining. This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis- played.

COROLLA_TMMMS_TMMC_U

2. Instrument cluster

99

Eco Driving Indicator (vehicles with a con- tinuously variable transmission)

 Monochrome display

 Color display

Eco Drive Indicator Light During Eco-friendly acceleration operation (Eco driving), Eco Driv- ing Indicator Light will turn on. When the acceleration exceeds Zone of Eco driving, and when the vehicle is stopped, the light turns off.

COROLLA_TMMMS_TMMC_U

100

2. Instrument cluster

Eco Drive Indicator Zone Display Suggests Zone of Eco driving with current Eco driving ratio based on acceleration.

Eco driving ratio based on acceleration If the acceleration exceeds Zone of Eco driving, the right side of Eco Driving Indicator Zone Display blinks. Zone of Eco driving

 Monochrome display

 Color display

Eco Driving Indicator Light customization  Vehicles with a monochrome display

P. 83

 Vehicles with a color display

P. 93

■Operation of Eco Driving Indicator

Eco Driving Indicator will not operate in the following conditions: ●The shift lever is in any position other than D. ●Paddle shift switch* is operated. ●Sport mode* is selected. ●The vehicle speed is approximately 80 mph (130 km/h) or higher. *: If equipped

COROLLA_TMMMS_TMMC_U

101

Operation of each component

3-1. Key information

Keys .................................. 102

3-2. Opening, closing and

locking the doors Doors ................................ 108
Trunk................................. 117
Smart key system ............. 122

3-3. Adjusting the seats

Front seats ........................ 130
Rear seats......................... 132
Head restraints.................. 134

3-4. Adjusting the steering

wheel and mirrors Steering wheel .................. 137
Inside rear view mirror ...... 139
Outside rear view mirrors............................. 141

3-5. Opening and closing

the windows Power windows ................. 143
Moon roof.......................... 147

COROLLA_TMMMS_TMMC_U

102

3-1. Key information

Keys

The keys The following keys are provided with the vehicle.  Vehicles without a smart key system (type A)

Keys Key number plate

 Vehicles without a smart key system (type B)

Keys Operating the wireless remote con- trol function Key number plate

 Vehicles with a smart key system

Electronic keys • Operating the smart key system

(P. 122)

• Operating the wireless remote

control function Mechanical keys Key number plate

COROLLA_TMMMS_TMMC_U

3

3-1. Key information

103

Wireless remote control (if equipped)  Vehicles without a smart key system

Locks all the doors (P. 108) Unlocks all the doors (P. 108) Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Sounds the alarm (P. 104) Opens the trunk (P. 118)

 Vehicles with a smart key system

Locks all the doors (P. 109) Unlocks all the doors (P. 109) Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the trunk (P. 118) Sounds the alarm (P. 104)

Using the mechanical key To take out the mechanical key, push the release button and take the key out.

The mechanical key can only be inserted in one direction, as the key only has grooves on one side. If the key cannot be inserted in a lock cylinder, turn it over and re- attempt to insert it. After using the mechanical key, store it in the electronic key. Carry the mechanical key together with the electronic key. If the electronic key bat- tery is depleted or the entry function does not operate properly, you will need the mechanical key. (P. 523)

COROLLA_TMMMS_TMMC_U

104

3-1. Key information

■Panic mode (with a wireless remote control function)

 Vehicles without a smart key system When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the wireless remote control.

 Vehicles with a smart key system When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the electronic key.

■If you lose your keys

New genuine keys can be made by your Toyota dealer using the other key (vehicles without a smart key system) or mechanical key (vehicles with a smart key system) and the key number stamped on your key number plate. Keep the plate in a safe place such as your wallet, not in the vehicle.

■When riding in an aircraft

When bringing a key with wireless remote control function onto an aircraft, make sure you do not press any button on the key while inside the aircraft cabin. If you are carrying the key in your bag etc., ensure that the buttons are not likely to be pressed accidentally. Pressing a button may cause the key to emit radio waves that could interfere with the operation of the aircraft.

COROLLA_TMMMS_TMMC_U

3

3-1. Key information

105

■Key battery depletion (vehicles with a wireless remote control function)

 Vehicles without a smart key system If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (P. 455)  Vehicles with a smart key system ●The standard battery life is 1 to 2 years. ●If the battery becomes low, an alarm will sound in the cabin when the engine

stops. (P. 503)

●As the electronic key always receives radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms indi- cate that the electronic key battery may be depleted. Replace the battery when necessary. (P. 455) • The smart key system or the wireless remote control does not operate. • The detection area becomes smaller. • The LED indicator on the key surface does not turn on.

●To avoid serious deterioration, do not leave the electronic key within 3 ft. (1

m) of the following electrical appliances that produce a magnetic field: • TVs • Personal computers • Cellular phones, cordless phones and battery chargers • Recharging cellular phones or cordless phones • Table lamps • Induction cookers ■Replacing the battery

P. 455

■Confirmation of the registered key number

The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details.

■If a wrong key is used (vehicles with a smart key system)

The key cylinder rotates freely to isolate inside mechanism.

COROLLA_TMMMS_TMMC_U

3-1. Key information

106
■Certification for the wireless remote control

FCC ID: HYQ12BEL

 For the U.S.A. FCC ID: HYQ23AAH NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For 12BEL The FCC ID/IC Certification number is affixed inside the equipment. You can find the ID/number when replacing the battery.  For Canada NOTE: This device complies with Industry Canada’s licence-exempt RSSs. Opera- tion is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. For 12BEL/12BDP The FCC ID/IC Certification number is affixed inside the equipment. You can find the ID/number when replacing the battery. NOTE: Le présent appareil est conforme aux CNR d'lndustrie Canada appli- cables aux appareils radio exempts de licence. L'exploitation est autori- sée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage; (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compro- mettre le fonctionnement. Pour 12BEL/12BDP L’identification FCC/le numéro d’accréditation IC est apposé(e) à l’intérieur de l’appareil. Cette identification/ce numéro est visible au remplacement de la pile.

■Customization

Settings (e.g. wireless remote control system) can be changed. (Customizable features: P. 564)

COROLLA_TMMMS_TMMC_U

3

3-1. Key information

107

NOTICE

■To prevent key damage

●Do not drop the keys, subject them to strong shocks or bend them. ●Do not expose the keys to high temperatures for long periods of time. ●Do not get the keys wet or wash them in an ultrasonic washer etc. ●Do not attach metallic or magnetic materials to the keys or place the keys

close to such materials.

●Do not disassemble the keys. ●Do not attach a sticker or anything else to the surface of the electronic key

and key (with a wireless remote control function).

●Vehicles with a smart key system: Do not place the keys near objects that produce magnetic fields, such as TVs, audio systems and induction cook- ers, or medical electrical equipment, such as low-frequency therapy equip- ment.

■Carrying the electronic key on your person (vehicles with a smart key

system) Carry the electronic key 3.9 in. (10 cm) or more away from electric appli- ances that are turned on. Radio waves emitted from electric appliances within 3.9 in. (10 cm) of the electronic key may interfere with the key, caus- ing the key to not function properly.

■In case of a smart key system malfunction or other key-related prob-

lems (vehicles with a smart key system) Take your vehicle with all the electronic keys provided with your vehicle to your Toyota dealer.

■When an electronic key is lost (vehicles with a smart key system)

If the electronic key remains lost, the risk of vehicle theft increases signifi- cantly. Visit your Toyota dealer immediately with all remaining electronic keys that was provided with your vehicle.

COROLLA_TMMMS_TMMC_U

108

3-2. Opening, closing and locking the doors

Doors

Unlocking and locking the doors from the outside ◆ Smart key system (if equipped)

Carry the electronic key to enable this function.

Grip the driver’s door handle to unlock the door. Grip the passenger’s door handle to unlock all the doors.* Make sure to touch the sensor on the back of the handle. The doors cannot be unlocked for 3 seconds after the doors are locked.

*: The door unlock settings can be changed. (P. 115)

Touch the lock sensor (the indentation on the upper part of the door handle) to lock all the doors. Check that the door is securely locked.

◆ Wireless remote control (if equipped)  Vehicles without a smart key system

Locks all the doors Check that the door is securely locked. Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the but- ton again within 5 seconds unlocks the other doors.

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

109

 Vehicles with a smart key system

Locks all the doors Check that the door is securely locked. Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the but- ton again within 5 seconds unlocks the other doors.

◆ Key

Turning the key operates the doors as follows:  Vehicles without a smart key system

Locks all the doors Unlocks all the doors Driver’s side only: Turning the key unlocks the driver's door. Turning the key again unlocks the other doors.

 Vehicles with a smart key system The doors can also be locked and unlocked with the mechanical key. (P. 523)

COROLLA_TMMMS_TMMC_U

110

3-2. Opening, closing and locking the doors

■Operation signals

A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: once; Unlocked: twice)

■Security feature

If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.

■When the door cannot be locked by the lock sensor on the upper part of

the door handle If the door will not lock even when the top- side sensor area is touched, try using your palm to touch the lock sensor.

■Door lock buzzer

If an attempt to lock the doors using the wireless remote control or smart key system is made when a door is not fully closed, a buzzer will sound for 5 sec- onds. Fully close the door, and lock the vehicle again.

■Setting the alarm (if equipped)

Locking the doors will set the alarm system. (P. 69)

■If the smart key system or the wireless remote control does not operate

properly Use the mechanical key to lock and unlock the doors. (P. 523) Replace the battery with a new one if it is depleted. (P. 455)

COROLLA_TMMMS_TMMC_U

3

3-2. Opening, closing and locking the doors

111

Unlocking and locking the doors from the inside ◆ Door lock switches Locks all the doors Unlocks all the doors

◆ Inside lock buttons

Locks the door Unlocks the door The front doors can be opened by pulling inside handle even if the lock buttons are in the lock position.

the

Locking the doors from the outside without a key

Move the inside lock button to the lock position. Close the door.

 Vehicles without a smart key system The door cannot be locked if either of the front doors is open and the key is in the engine switch.  Vehicles with a smart key system The door cannot be locked if the engine switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle. However, the key may not be detected correctly and the door may be locked.

COROLLA_TMMMS_TMMC_U

112

3-2. Opening, closing and locking the doors

Rear door child-protector lock The door cannot be opened from inside the vehicle when the lock is set.

Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

113

Automatic door locking and unlocking systems The following functions can be set or cancelled:

Function

Operation

Shift position linked door locking function*1
Shift position linked door unlocking function*1

Speed linked door locking function*2

Shifting the shift lever out of P locks all doors. Shifting the shift lever to P unlocks all doors. All doors are locked when the vehi- cle speed is approximately 12 mph (20 km/h) or higher.  Vehicles without a smart key sys-

tem

Driver’s door linked door unlocking function

All doors are unlocked when the driver's door is opened within approximately 45 seconds of turning the engine switch to “ACC” or “LOCK”.  Vehicles with a smart key system All doors are unlocked when the driver's door is opened within approximately 45 seconds of turning the engine switch to ACCESSORY mode or OFF. *1: Vehicles with a continuously variable transmission *2: Vehicles with a smart key system

COROLLA_TMMMS_TMMC_U

114

3-2. Opening, closing and locking the doors

■ Setting and canceling the functions

To switch between set and canceled, follow the procedure below:

Vehicles without a smart key system: Close all the doors and switch the engine switch to the “ON” position. (Perform step within 20 seconds.) Vehicles with a smart key system: Close all the doors and switch the engine switch to IGNITION ON mode. (Perform step within 20 seconds.) Shift the shift lever to P or N, and press and hold the lock switch driver's door or for approximately 5 seconds and then release. The shift lever and switch posi- tions corresponding the desired function to be set are shown as follows. Use the same procedure to cancel the function.

to

Function

Shift lever position

Driver’s door lock switch position

linked door

Shift position linked door lock- ing function*1
Shift position unlocking function*1
Speed linked door locking func- tion*2
Driver's door unlocking function

linked door

*1: Vehicles with a continuously variable transmission *2: Vehicles with a smart key system When the setting or canceling operation is complete, all doors are locked and then unlocked.

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

115

■Switching the door unlock function (vehicles with a smart key system) It is possible to set which doors the entry function unlocks using the wireless remote control.

Turn the engine switch off. When the indicator light on the key surface is not on, press and hold

for approximately 5 seconds while pressing and holding

or

The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step

.) Multi-information display

Monochrome

display

Color display

Unlocking function

Beep

the Holding driver’s door handle unlocks only the driver’s door. Holding the front passenger’s door handle unlocks all the doors.

Exterior: Beeps 3 times Interior: Pings once

Holding either front door han- dle unlocks all the doors.

Exterior: Beeps twice Interior: Pings once

Vehicles with an alarm: To prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 sec- onds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm. (P. 69)

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

116
■Conditions affecting the operation of the smart key system or wireless

remote control (with a wireless remote control function)  Vehicles without a smart key system The wireless remote control function may not operate normally in the follow- ing situations: ●When the wireless key battery is depleted ●Near a TV tower, radio station, electric power plant, airport or other facility

that generates strong radio waves

●When carrying a portable radio, cellular phone or other wireless communi-

cation devices

●When multiple wireless keys are in the vicinity ●When the wireless key is in contact with, or is covered by a metallic object ●When a wireless key (that emits radio waves) is being used nearby ●When the wireless key has been left near an electrical appliance such as a

personal computer

●If window tint with a metallic content or metallic objects are attached to the

rear window

 Vehicles with a smart key system P. 125

■Customization

Settings (e.g. unlocking function using a key) can be changed. (Customizable features: P. 564)

WARNING

■To prevent an accident

Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock all the doors. ●Ensure that all doors are properly closed. ●Do not pull the inside handle of the doors while driving.

The doors may be opened and the passengers are thrown out of the vehi- cle and it may result in serious injury or death. Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.

●Set the rear door child-protector locks when children are seated in the rear

seats.

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

117

Trunk The trunk can be opened using the trunk opener, entry function, wireless remote control or key.

Opening the trunk from inside the vehicle Pull up the lever to release the trunk lid.

Opening the trunk from outside the vehicle ◆ Smart key system (if equipped)

While carrying the electronic key, press the button on the trunk lid.

When all the doors are unlocked with the power door lock sys- tem, the trunk can be opened without carrying the electronic key.

COROLLA_TMMMS_TMMC_U

118

3-2. Opening, closing and locking the doors ◆ Wireless remote control (if equipped)  Vehicles without a smart key system Press and hold the switch.

 Vehicles with a smart key system Press and hold the switch.

◆ Key (vehicles with a key cylinder on the trunk lid)

the key clockwise

Turn release the trunk lid.

to

COROLLA_TMMMS_TMMC_U

3

3-2. Opening, closing and locking the doors

119

■Operation signal (with a wireless remote control function)

A buzzer sounds to indicate that the trunk has been opened.

■Trunk light

The trunk light turns on when the trunk is opened.

■Function to prevent the trunk being locked with the electronic key inside

(vehicles with a smart key system) ●When all doors are being locked, closing the trunk lid with the electronic key

left inside the trunk will sound an alarm. In this case, the trunk lid can be opened by pressing the trunk release but- ton on the trunk lid.

●Even when the spare electronic key is put in the trunk with all the doors locked, the key confinement prevention function can be activated so the trunk can be opened. In order to prevent theft, take all electronic keys with you when leaving the vehicle.

●Even when the electronic key is put in the trunk with all the doors are locked, the key may not be detected depending on the places and the surrounding radio wave conditions. In this case, the key confinement prevention function cannot be activated, causing the doors to lock when the trunk is closed. Make sure to check where the key is before closing the trunk.

●The key confinement prevention function cannot be activated if any one of

the doors is unlocked. In this case, open the trunk using the trunk opener.

■Internal trunk release lever

The trunk lid can be opened by pushing the glow-in-the-dark lever located on the inside of the trunk lid to the side. The lever will continue to glow for some time after the trunk lid is closed.

■Customization

The trunk unlocking operation can be changed. (Customizable features: P. 564)

COROLLA_TMMMS_TMMC_U

120

3-2. Opening, closing and locking the doors

WARNING

■Caution while driving

●Keep the trunk lid closed while driving.

If the trunk lid is left open, it may hit near-by objects while driving or lug- gage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the trunk lid before driving.

●Before driving the vehicle, make sure that the trunk lid is fully closed. If the trunk lid is not fully closed, it may open unexpectedly while driving, caus- ing an accident.

●Never let anyone sit in the trunk. In the event of sudden braking or a colli-

sion, they are susceptible to death or serious injury.

■When a child is in the vehicle

Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not allow a child to play in the trunk.

If a child is accidentally locked in the trunk, the child could suffer from heat exhaustion, suffocation or other injuries.

●Do not allow a child to open or close the trunk lid.

Doing so may cause the trunk lid to operate unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing trunk lid.

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

121

WARNING

■Using the trunk

Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in seri- ous injury. ●Remove any heavy loads, such as snow and ice, from the trunk lid before opening it. Failure to do so may cause the trunk lid to suddenly shut again after it is opened.

●When opening or closing the trunk lid, thoroughly check to make sure the

surrounding area is safe.

●If anyone is in the vicinity, make sure they are safe and let them know that

the trunk is about to open or close.

●Use caution when opening or closing the trunk lid in windy weather as it

may move abruptly in strong wind.

●The trunk lid may suddenly shut if it is not opened fully. It is more difficult to open or close the trunk lid on an incline than on a level surface, so beware of the trunk lid unexpectedly opening or closing by itself. Make sure that the trunk lid is fully open and secure before using the trunk.

●When closing the trunk lid, take extra care to prevent your fingers etc. from being caught.

●When closing the trunk lid, make sure to press it lightly on its outer surface. If the trunk handle is used to fully close the trunk lid, it may result in hands or arms being caught.

●Do not attach any accessories other than genuine Toyota parts to the trunk lid. Such additional weight on the trunk lid may cause the lid to suddenly shut again after it is opened.

COROLLA_TMMMS_TMMC_U

122

3-2. Opening, closing and locking the doors

Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.)

● Locks and unlocks the doors (P. 108) ● Opens the trunk (P. 117) ● Starts the engine (P. 174)

■Antenna location

Antennas outside the cabin Antennas inside the cabin Antenna inside the trunk Antenna outside the trunk

: If equipped

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

123

■Effective range (areas within which the electronic key is detected)

When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3
ft. (0.7 m) of either of the outside front door handles. (Only the doors detecting the key can be operated.) When starting the engine or changing engine switch modes The system can be operated when the electronic key is inside the vehicle. When opening the trunk The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of the trunk release button.

■Alarms and warning indicators

A combination of exterior and interior alarms as well as warning messages shown on the multi-information display are used to prevent theft of the vehicle and accidents resulting from erroneous operation. Take appropriate mea- sures in response to any warning message on the multi-information display. (P. 489) The following table describes circumstances and correction procedures when only alarms are sounded.

Alarm

Situation

Exterior alarm sounds once for 5 seconds

Interior alarm sounds continuously

An attempt was made to lock the vehicle while a door was open. The trunk was closed while the electronic key was still inside the trunk and all the doors were locked. The engine switch was turned to ACCESSORY mode while the driver’s door was open (or the was driver’s opened the engine switch was in ACCESSORY mode).

door while

Correction procedure Close all of the doors and the doors again.

lock

Retrieve the electronic key from the trunk and close the trunk lid.

Turn the engine switch off and the driver’s door.

close

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

124
■Battery-saving function

The battery-saving function will be activated in order to prevent the electronic key battery and the vehicle battery from being discharged while the vehicle is not in operation for a long time. ●In the following situations, the smart key system may take some time to

unlock the doors. • The electronic key has been left in an area of approximately 6 ft. (2 m) of

the outside of the vehicle for 10 minutes or longer.

• The smart key system has not been used for 5 days or longer.

●If the smart key system has not been used for 14 days or longer, the doors cannot be unlocked at any doors except the driver’s door. In this case, take hold of the driver’s door handle, or use the wireless remote control or the mechanical key, to unlock the doors.

■Electronic Key Battery-Saving Function

twice while pressing and . Confirm that the electronic

When battery-saving mode is set, battery depletion is minimized by stopping the electronic key from receiving radio waves. Press holding key indicator flashes 4 times. While the battery-saving mode is set, the smart key system cannot be used. To cancel the function, press any of the elec- tronic key buttons.

COROLLA_TMMMS_TMMC_U

3

3-2. Opening, closing and locking the doors

125

■Conditions affecting operation

The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and engine immobi- lizer system from operating properly. (Ways of coping: P. 523) ●When the electronic key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electrical noise

●When carrying a portable radio, cellular phone, cordless phone or other

wireless communication device

●When the electronic key is in contact with, or is covered by the following

metallic objects • Cards to which aluminum foil is attached • Cigarette boxes that have aluminum foil inside • Metallic wallets or bags • Coins • Hand warmers made of metal • Media such as CDs and DVDs

●When other wireless keys (that emit radio waves) are being used nearby ●When carrying the electronic key together with the following devices that

emit radio waves • Another vehicle’s electronic key or a wireless key that emits radio waves • Personal computers or personal digital assistants (PDAs) • Digital audio players • Portable game systems

●If window tint with a metallic content or metallic objects are attached to the

rear window

●When the electronic key is placed near a battery charger or electronic

devices

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

126
■Note for the entry function

●Even when the electronic key is within the effective range (detection areas),

the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near

the ground, or in a high place when the doors are locked or unlocked.

• The electronic key is near the ground or in a high place, or too close to

the rear bumper center when the trunk is opened.

• The electronic key is on the instrument panel, rear package tray or floor, or in the door pockets or glove box when the engine is started or engine switch modes are changed.

●Do not leave the electronic key on top of the instrument panel or near the door pockets when exiting the vehicle. Depending on the radio wave recep- tion conditions, it may be detected by the antenna outside the cabin and the doors will become lockable from the outside, possibly trapping the electronic key inside the vehicle.

●As long as the electronic key is within the effective range, the doors may be locked or unlocked by anyone. However, only the doors detecting the elec- tronic key can be used to unlock the vehicle.

●Even if the electronic key is not inside the vehicle, it may be possible to start

the engine if the electronic key is near the window.

●The doors may unlock or lock if a large amount of water splashes on the door handle, such as in the rain or in a car wash, when the electronic key is within the effective range. (The doors will automatically be locked after approximately 60 seconds if the doors are not opened and closed.)

●If the wireless remote control is used to lock the doors when the electronic key is near the vehicle, there is a possibility that the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)

●Touching the door lock or unlock sensor while wearing gloves may prevent

lock or unlock operation.

●When the lock operation is performed using the lock sensor, recognition sig- nals will be shown up to two consecutive times. After this, no recognition signals will be given.

●If the door handle becomes wet while the electronic key is within the effec- tive range, the door may lock and unlock repeatedly. In this case, follow the following correction procedures to wash the vehicle: • Place the electronic key in a location 6 ft. (2 m) or more away from the

vehicle. (Take care to ensure that the key is not stolen.)

• Set the electronic key to battery-saving mode to disable the smart key

system. (P. 124)

COROLLA_TMMMS_TMMC_U

3

3-2. Opening, closing and locking the doors

127

●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a message may be shown on the multi-information dis- play and a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.

●The lock sensor may not work properly if it comes into contact with ice,

snow, mud, etc. Clean the lock sensor and attempt to operate it again.

●If there is another electronic key in the detection area, it may take slightly

longer to unlock the doors after the door handle is gripped.

●Fingernails may scrape against the door during operation of the door han-

dle. Be careful not to injure fingernails or damage the surface of the door.

●A sudden handle operation or a handle operation immediately after entering the effective range may prevent the doors from being unlocked. Touch the door unlock sensor and check that the doors are unlocked before pulling the door handle again.

●Unlocking the vehicle may take more time if another electronic key is within

the effective range.

■When the vehicle is not driven for extended periods

●To prevent theft of the vehicle, do not leave the electronic key within 6 ft. (2

m) of the vehicle.

●The smart key system can be deactivated in advance. (P. 564)

■To operate the system properly

Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the outside of the vehicle. Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention function may not operate.)

■If the smart key system does not operate properly

●Locking and unlocking the doors: Use the mechanical key. (P. 523) ●Starting the engine: P. 524

■Customization

Settings (e. g. smart key system) can be changed. (Customizable features: P. 564)

■If the smart key system has been deactivated in a customized setting

●Locking and unlocking the doors and opening the trunk:

Use the wireless remote control or mechanical key. (P. 118, 523)

●Starting the engine and changing engine switch modes: P. 524
●Stopping the engine: P. 175

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

128
■Certification for the smart key system

FCC ID: HYQ14FBA

 For the U.S.A. FCC ID: HYQ23AAB NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.  For Canada NOTE: This device complies with Industry Canada’s licence-exempt RSSs. Opera- tion is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.  For the U.S.A. FCC ID: NI4TMLF10-51
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.  For Canada This device complies with Industry Canada’s licence-exempt RSSs. Opera- tion is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. NOTE: Le présent appareil est conforme aux CNR d’lndustrie Canada appli- cables aux appareils radio exempts de licence. L’exploitation est autori- sée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compro- mettre le fonctionnement.

COROLLA_TMMMS_TMMC_U

3-2. Opening, closing and locking the doors

129

WARNING

■Caution regarding interference with electronic devices

●People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should keep away from the smart key system antennas. (P. 122) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of the emitted radio waves. Then, consult your doctor to see if you should disable the entry function.

●User of any electrical medical device other than implantable cardiac pace- makers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.

Ask your Toyota dealer for details for disabling the entry function.

COROLLA_TMMMS_TMMC_U

130

3-3. Adjusting the seats

Front seats

Adjustment procedure  Manual seat

Seat position adjustment lever Seatback angle adjustment lever

 Power seat (driver’s side only)

Vertical height adjustment lever (driver’s side only)

position

adjustment

Seat switch Seatback angle adjustment switch

(front) angle

Seat cushion adjustment switch Vertical height adjustment switch

COROLLA_TMMMS_TMMC_U

3-3. Adjusting the seats

131

WARNING

■Seat adjustment

●Be careful that the seat does not hit passengers or luggage. ●Do not recline the seat more than necessary when the vehicle is in motion

to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident.

●Manual seat only: After adjusting the seat, make sure that the seat is

locked in position.

■When adjusting the seat positions

Make sure to leave enough space around the feet so they do not get stuck.