2004 Toyota 4runner Owners Manual

while still maintaining control of the ve- hicle. Parts of the airbag module (steering wheel hub, airbag cover and inflator) may be hot for several minutes after deployment, so do not inflate only once. The windshield may be damaged by absorbing some of the force of the inflat- ing airbag.

touch! The airbags

the occupant

CAUTION

The driver or front passenger who is too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. Toyota strongly recommends that: (cid:1) The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle.

(cid:1) The front passenger sit as far back

as possible from the dashboard.

(cid:1) All vehicle occupants be properly restrained using the available seat belts.

For instructions and precautions con- cerning the seating position, see “—Front seat precautions” on page 40 in this Section.

73

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

(cid:1) Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” on page 88 in this Sec- tion.

(cid:1) Toyota strongly recommends that all infants and children be placed in the rear seat of the vehicle and be properly restrained.

(cid:1) Do not allow a child to stand up or kneel on the front passenger seat, front passenger airbag since could considerable speed and the child may be killed or seriously in- jured.

the inflate with

force. Otherwise,

is

in use, since

(cid:1) Do not sit on the edge of the seat or lean against the dashboard when the vehicle the front passenger airbag could inflate with considerable speed and force. Anyone who is up against, or very close to, an airbag when it inflates, can be killed or seriously injured. Sit up straight and well back in the seat, and always use your seat belt properly.

74

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

the

(cid:1) Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, dashboard near front passenger airbag, front passenger airbag cover, front passenger airbag or airbag sensor assembly. Doing so may prevent the front airbag system from activating correctly, cause sudden activation of the system or disable the sys- tem, which could result in death or serious injury.

Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repair and modification.

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can in- terfere with proper operation of the SRS front airbag system in some cases. (cid:1) Installation of electronic devices such as a mobile two-way radio, cassette tape player or compact disc player

(cid:1) Modification of the suspension sys-

tem

(cid:1) Modification of the front end struc-

ture

(cid:1) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

(cid:1) Repairs made on or near the front fenders, front end structure, con- sole, steering column, steering wheel or dashboard near the front passenger airbag

75

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

(cid:1) Do not put anything or any part of your body on or in front of the dashboard or steering wheel pad that houses the front airbag sys- tem. They might restrict inflation or cause death or serious injury as they are projected rearward by the force of the deploying airbags. Like- wise, the driver and front passenger should not hold objects their arms or on their knees.

in

’04 4Runner_U (L/O 0409)

If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible. (cid:1) The light does not come on when the ignition key is turned to the “ON” posi- tion or remains on for more than 6
seconds or flashes.

(cid:1) The light comes on or starts flashing

while driving.

light system monitors

This indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after about 6 seconds. This means the SRS front airbags are oper- ating properly. This warning the airbag sensor assembly, front airbag sen- sors, side and curtain shield airbag sen- sors, curtain shield airbag sensors, driv- er’s seat position sensor, driver’s seat belt buckle switch, seat belt pretensioner as- semblies, inflators, warning light, “RSCA OFF” indicator light, interconnecting wiring and power sources. (For details, see “Ser- vice reminder indicators and warning buzz- ers” on page 139 in Section 1- 6.)

76

In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The SRS front airbags have been in-

flated.

(cid:1) The front of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS front airbags to inflate.

(cid:1) The pad section of the steering wheel or dashboard (shaded in the illustra- tion) is scratched, cracked, or other- wise damaged.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

SRS side airbags and curtain shield airbags

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

The SRS (Supplemental Restraint Sys- tem) side airbags and curtain shield air- bags are designed to provide further protection for the driver, front passen- ger and rear passengers* 1/second pas- sengers* 2 the primary safety protection provided by the seat belts. * 1: Without third seats * 2: With third seats

in addition to

In response to a severe side impact, the SRS side airbag and curtain shield airbags in the impacted side work with the seat belts to help reduce injury by inflating. The SRS side airbags help reduce injuries mainly to the driver’s or front passenger’s chest. The SRS curtain shield airbags help reduce injuries mainly to the driver’s, front passenger’s or rear/second passen- ger’s head and help prevent them from being thrown out of the vehicle. The SRS side airbag and curtain shield airbag on the passenger side are activated even with no passenger in the front seat or rear/second seat. Roll sensing function: In response to a vehicle rollover, the cur- tain shield airbags on both sides work with the seat belts to help reduce injury by inflating. The curtain shield airbags help reduce injuries mainly to the driver’s, front passenger’s or rear/second passen- ger’s head and help prevent them from being the vehicle. (This function can be turned off if inflation is not desired. See “Roll sensing of curtain shield airbags off switch” on page 87 in this Section.) The SRS curtain shield airbags may acti- vate even when the side airbags are not activated.

thrown out of

77

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

restraint

(cid:1) Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing airbags. An infant or child who is too small to use a seat belt should be properly secured using a child Toyota strongly recommends in- fants and children be placed in the rear seats of the vehicle and prop- erly restrained. The rear seats are the safest for infants and children. For the installation of a child restraint sys- tem, see “Child restraint” on page 88 in this Section.

instructions concerning

that all

system.

(cid:1) Do not allow anyone to lean his/her head or any part of his/her body against the door or the area of the seat, front pillar, rear pillar or roof side rail from which the SRS side airbag and curtain shield airbag deploy even is a child seated in the child restraint system. It is dangerous if the SRS side air- bag and curtain shield airbag in- flate, and the impact of the deploy- ing airbag could cause death or se- rious injury to the occupant.

if he/she

Always wear your seat belt properly. Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seat belt restraint system by the driver and front passenger when the SRS side airbags and curtain shield airbags are inflated.

CAUTION

to

(cid:1) The SRS side airbag and curtain is designed shield airbag system the only as a supplement the driver, primary protection of front passenger and rear /second passenger seat belt systems. To ensure maximum protection in an accident, the driver and all passen- gers in the vehicle must wear their seat belts properly. Wearing a seat belt properly during an accident reduces the chances of death or serious injury or being thrown out of the vehicle. For instructions and precautions concerning the seat belt system, see “Seat belts” on page 61 in this Section.

78

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Collision from the rear

Collision from the front

Vehicle rollover

The SRS side airbags are not generally designed to inflate if the vehicle is in- volved in a front or rear collision, if it rolls over, or if it is involved in a low- speed side collision.

The SRS side airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment as shown in the illustration. The SRS side airbags are designed to inflate when the passenger compartment area suffers a severe the side. Always wear your seat belts properly.

impact

from

from

The curtain shield airbags may not acti- if the vehicle is subjected to a vate collision the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment as shown in the illustra- tion. The curtain shield airbags are designed to inflate when the passenger compartment area suffers a severe the side or vehicle rollover. Always wear your seat belts properly.

impact

from

79

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Collision from the front

Collision from the rear

Hitting a curb, edge of pavement or hard surface

Falling into or jumping over a deep hole

The angle of vehicle tip- up is marginal

Skidding vehicle hitting a curb stone

Pitch end over end

Landing hard or vehicle falling

The curtain shield airbags may inflate if the angle of vehicle tip- up is margin- al or if the skidding vehicle’s tires hit a curb stone laterally as shown in the illustration.

The curtain shield airbags are not gen- erally designed to inflate if the vehicle is involved in a front or rear collision, if it pitches end over end, or if it is involved in a low- speed side collision.

The SRS side and curtain shield airbags may deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

80

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

inflators and/or

The SRS side airbag and curtain shield airbag system is controlled by the airbag sensor assembly. The airbag sensor as- sembly consists of a safing sensor and airbag sensor. the side and In a severe side impact, curtain shield airbag sensor and/or the curtain shield airbag sensor trigger(s) the the curtain side airbag shield airbag time a chemical reaction in the inflators quickly fills the airbags with non- toxic gas to help restrain the occu- pants. In a vehicle rollover, the airbag sensor assembly triggers the curtain shield airbag inflator. At this time, a chemical reaction in the airbags with non- toxic gas to help restrain the lateral motion of the occupants.

the lateral motion of

inflators quickly

inflators. At

this

fills

the

When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non- toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation with soap and water. If you can safely exit from the vehicle, you should do so imme- diately. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Front seats as well as parts of the front and rear pillars, front, center and rear garnish and roof interior may be hot for several minutes, but them- selves will not be hot. The airbags are designed to inflate only once.

the airbags

81

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

The SRS side airbag and curtain shield airbag system consists mainly of the fol- lowing components, and their locations are shown in the illustration. 1. SRS warning light 2. Curtain shield airbag modules

(airbag and inflator)

3. Side airbag modules

(airbag and inflator)

4. Curtain shield airbag sensors 5. Side and curtain shield airbag sensors 6. Airbag sensor assembly

’04 4Runner_U (L/O 0409)

CAUTION

inflate with

SRS side airbags and curtain shield airbags considerable force. To reduce the possibility of death or serious injury when they in- flate, the driver, front passenger and rear/second passengers must: (cid:1) Wear their seat belts properly. (cid:1) Remain properly seated with their backs upright and against the seats at all times.

Improper sitting and wearing of the seat belts may not retain you inside the vehicle.

82

(cid:1) Do not allow anyone to lean against the door when the vehicle is in use, since the side airbag and curtain shield airbag could inflate with con- siderable speed and force. Other- wise, he/she may be killed or seri- ously injured. Special care should be taken especially when you have a small child in the vehicle.

(cid:1) Sit up straight and well back in the seat, distributing your weight evenly in the seat. Do not apply excessive weight the seats with a side airbag, and to the front pillar, rear pillar and roof side rail with a curtain shield airbag.

the outer side of

to

Type A

Type B

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

(cid:1) Make sure the “RSCA OFF” indica- tor light is off. The curtain shield airbags will not inflate in a vehicle rollover if this indicator light is on and you may be killed or seriously injured. For details, see “Roll sens- ing of curtain shield airbags off switch” on page 87 in this Section.

inflate, since

(cid:1) Do not allow anyone to get his/her head closer to the area where the side airbag and curtain shield air- bag these airbags could considerable speed and force. Otherwise, he/she may be killed or seriously injured. Special care should be taken espe- cially when you have a small child in the vehicle.

inflate with

(cid:1) Do not allow anyone to kneel on the passenger seat, facing the pas- senger’s side door, since the side airbag and curtain shield airbag could considerable speed and force. Otherwise, he/she may be killed or seriously injured. Special care should be taken espe- cially when you have a small child in the vehicle.

inflate with

83

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

(cid:1) Do not allow anyone to get his/her head or hands out of windows the curtain shield airbags since could inflate with considerable speed and force. Otherwise, he/she may be killed or seriously injured. Special care should be taken espe- cially when you have a small child in the vehicle.

(cid:1) Do not attach a cup holder or any other device or object on or around the door. When the side airbag in- flates, the cup holder or any other device or object will be thrown with great force or the side airbag may not activate correctly, resulting in injury. Likewise, death or serious the driver and front passenger should not hold objects their arms or on their knees.

in

(cid:1) Do not attach a microphone or any other device or object near the area where the curtain shield airbags ac- tivate such as on the windshield glass, side door glass, front, center and roof side garnish, roof interior or assist grips. When the curtain shield airbags the micro- phone or other device or object will be hurled with great force or the curtain shield airbags may not acti- vate correctly, which could result in death or serious injury.

inflate,

84

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

(cid:1) Do not hook a hanger, heavy or sharp pointed objects on the coat hook. If the curtain shield airbag inflates, those items will be thrown away with great force or the curtain shield airbag may not activate cor- rectly, resulting in death or serious injury. When you hang clothes, hang them on the coat hook direct- ly.

(cid:1) Do not use seat accessories which cover the parts where the side air- bags inflate. Such accessories may prevent the side airbags from acti- vating correctly, causing death or serious injury.

(cid:1) Do not modify or replace the seats or upholstery of the seats with side airbags. Such changes may prevent the side airbag system from activat- ing correctly, disable the system or cause the side airbags to inflate ac- cidentally, resulting in death or seri- ous injury.

(cid:1) Do not disassemble or repair the front pillars and roof side rails con- taining the curtain shield airbags. Such changes may disable the sys- tem or cause the curtain shield air- bags to inflate accidentally, result- ing in death or serious injury.

(cid:1) Do not modify or change the sus- pension system. Such changes may cause the curtain shield airbags to inflate accidentally, which could re- sult in death or serious injury.

the manufacturer’s

(cid:1) Do not use tires or wheels other than recom- mended size. Such a use may cause the curtain shield airbags to inflate accidentally, which could result in death or serious injury. For details, see “Checking and replacing tires” on page 372 in Section 7- 2.

(cid:1) Do not place luggage heavier than specified on the roof luggage carri- er. Such luggage may cause the curtain shield airbags to inflate ac- cidentally, which could in death or serious injury. For details, see “Roof luggage carrier” on page 268 in Section 1- 10.

result

Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repair and modification.

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the SRS side airbag and curtain shield airbag system in some cases. (cid:1) Installation of electronic devices such as a mobile two-way radio, cassette tape player or compact disc player

(cid:1) Modification of the side structure of

the passenger compartment

(cid:1) Repairs made on or near the con-

sole or front seat

85

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible. (cid:1) The light does not come on when the ignition key is turned to the “ON” posi- tion or remains on for more than 6
seconds or flashes.

(cid:1) The light comes on or starts flashing

while driving.

light system monitors

This indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after about 6 seconds. This means the SRS side airbags and curtain shield airbags are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side and curtain shield airbag sen- sors, curtain shield airbag sensors, driv- er’s seat position sensor, driver’s seat belt buckle switch, seat belt pretensioner as- semblies, inflators, warning light, “RSCA OFF” indicator light, interconnecting wiring and power sources. (For details, see “Ser- vice reminder indicators and warning buzz- ers” on page 139 in Section 1- 6.)

86

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Roll sensing of curtain shield airbags off switch

In the following cases, contact your Toyota dealer as soon as possible: (cid:1) Any of the SRS side airbags and cur- tain shield airbags have been inflated. (cid:1) The portion of the doors (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield airbags to inflate.

(cid:1) The surface of the seats with the side airbag (shaded is scratched, cracked, or otherwise dam- aged.

illustration)

the

in

(cid:1) The portion of

the front, center and rear garnish, and roof interior contain- ing inside (shaded in the illustration) is scratched, cracked, or otherwise damaged.

the curtain shield airbags

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

The roll sensing of curtain shield air- bags off switch (“RSCA OFF” switch) can turn off the curtain shield airbags and seat belt pretensioners in a vehicle rollover. This switch should only be used if inflation is not desired (such as extreme off- road driving).

is

function

turned on.

When you push the “RSCA OFF” switch for a few seconds with the ignition switch on, the “RSCA OFF” indicator light comes on and the roll sensing function is turned off. When you push the switch again, the indicator light goes off and the roll sens- ing (For details about the roll sensing function, see “SRS side airbags and curtain shield airbags” on page 77 in this Section.) In a severe side impact, the curtain shield airbags on impacted side will inflate even if the roll sensing function is turned off. (For details about the curtain shield air- bags, see “SRS side airbags and curtain shield airbags” on page 77 in this Sec- tion.) In a severe frontal impact, the seat belt pretensioners will work even if the roll sensing function is turned off. (For details about the seat belt pretensioners, see “—Seat belt pretensioners” on page 67 in this Section.) If the ignition switch is turned to “ACC” or “LOCK” with the roll sensing function off and then the ignition switch is turned back to “ON”, the roll sensing function will turn back on automatically.

87

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

CAUTION

(cid:1) Before normal driving, make sure the “RSCA OFF” indicator light is off.

light

(cid:1) When the roll sensing function is turned off (and the “RSCA OFF” indicator is on), the curtain shield airbags and seat belt preten- sioners will not work in a vehicle rollover. Turning off the curtain shield airbags and seat belt preten- sioners reduces occupant protection which your vehicle safety systems can provide in- crease the likelihood of death or serious injuries.

in accidents and

88

’04 4Runner_U (L/O 0409)

Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- propriate child restraint systems for children. The laws of all 50 states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAE J1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts” on page 61 in this Section for details.

CAUTION

(cid:1) For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.

(cid:1) Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, and is put on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. (cid:1) Never install a rear- facing child re- straint system on the front passen- ger seat. In the event of an acci- dent, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child the rear- facing child re- straint system is installed on the front passenger seat.

if

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

the

(cid:1) A forward- facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the front pas- inflate with senger airbag could considerable speed and force. Otherwise, the child may be killed or seriously injured.

(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.

If

installing a child

(cid:1) Do not use the seat belt extender when restraint system on the front or rear passen- ger seat. installing a child re- straint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of collision.

(cid:1) Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly se- cured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sud- den stop or accident.

—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap por- tion of the lap/shoulder belt. You must carefully consult the manufacturer’s instructions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. restraint system should be The child installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. When not using the child restraint system, keep it secured with the seat belt or place it somewhere other the passenger compartment. This will prevent it from in- juring passengers in the event of a sud- den stop or accident.

than

89

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

(A) Infant seat

(C) Booster seat

—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchor brackets for se- curing the top strap of a child restraint system. For instructions about how to use the an- chor bracket, see “—Using a top strap” on page 100 in this Section. The child restraint lower anchorages ap- proved for your vehicle may also be used. See “—Installation with child restraint low- er anchorages” on page 104 in this Sec- tion.

90

(B) Convertible seat

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

—Installation with seat belt

(A) INFANT SEAT INSTALLATION An infant seat must be used in rear- facing position only.

CAUTION

(cid:1) Never install a rear- facing child re- straint system on the front passen- ger seat. In the event of an acci- dent, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child the rear- facing child re- straint system is installed on the front passenger seat.

if

(cid:1) Do not install a child restraint sys- tem on the second (or third) seat if it interferes with the lock mecha- nism of the front (or second) seats. Otherwise, the child or front (or second) seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.

91

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

92

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

93

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Move seat fully back

CAUTION

(cid:1) Never install a rear- facing child re- straint system on the front passen- ger seat. In the event of an acci- dent, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child the rear- facing child re- straint system is installed on the front passenger seat.

if

the

(cid:1) A forward- facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible, because the front pas- inflate with senger airbag could considerable speed and force. Otherwise, the child may be killed or seriously injured.

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward- facing or rear- facing position de- pending on the age and size of the the child. When manufacturer’s the applicable age and size of the child as well as directions the child restraint system.

installing, follow instructions about

installing

for

94

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.

(cid:1) Do not install a child restraint sys- tem on the second (or third) seat if it interferes with the lock mecha- nism of the front (or second) seats. Otherwise, the child or front (or second) seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

95

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

96

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward- facing position only.

97

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 61 in this Section for details.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

Move seat fully back

CAUTION

the

(cid:1) A forward- facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the front pas- senger airbag could inflate with considerable force. and speed Otherwise, the child may be killed or seriously injured.

98

’04 4Runner_U (L/O 0409)

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.

(cid:1) If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

could

(cid:1) Both high- positioned lap belts and cause loose- fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.

injuries due

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2. To remove the child restraint system, the buckle release button and

press allow the belt to retract.

99

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

—Using a top strap (vehicles without third seats)

Follow the procedure below for a child restraint system that requires the use of a top strap.

100

’04 4Runner_U (L/O 0409)

Anchor brackets

Symbol

Use the anchor brackets behind the rear seatbacks to attach the top strap. Anchor brackets are rear seating position. This symbol indicates the location of the anchor brackets.

for each

installed

TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

2. Raise the anchor bracket.

3. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

4. Replace the head restraint.

instructions

For the child re- straint system, see “Child restraint” on page 88 in this Section.

install

to

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

101

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

—Using a top strap (vehicles with third seats)

Anchor brackets

Symbol

Lower the anchor bracket when it is not in use.

Follow the procedure below for a child restraint system that requires the use of a top strap.

Use the anchor brackets behind the sec- ond seatbacks to attach the top strap. Anchor brackets are second seat. This symbol indicates the location of the anchor brackets.

for each

installed

102

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.

2. Open the anchor bracket cover.

3. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint” on page 88 in this Section.

install

to

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

103

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

—Installation with child restraint lower anchorages (vehicles without third seats)

4. Replace the head restraint. Close the anchor bracket cover when the anchor bracket is not used.

specifications

Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the rear seats. The anchorages are installed in the gap between the seat cushion and seatback of both outside rear seats. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

104

Canada only

Type A buttons)

(anchor position

indicated by

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Canada only

Canada only

Canada only

Type A tags)

(anchor position

indicated by

Type B buttons)

(anchor position

indicated by

Type B tags)

(anchor position

indicated by

105

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

SYSTEM

CAUTION

—Installation with child restraint lower anchorages (vehicles with third seats)

RESTRAINT

CHILD INSTALLATION 1. Widen

the gap between

the seat cushion and seatback slightly and confirm the position of the lower an- chorages near the buttons or tags on the seatback.

2. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 100 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

106

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

the

lock mechanism of

(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

specifications

Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the second seats. The anchorages are installed in the seat cushion of the right side seating position and between the center and left side seat- ing position. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

5th lock position

1st lock position

2. Take off the cover on the seat cush-

ion.

SYSTEM

RESTRAINT

CHILD INSTALLATION 1. Fold down the seatback. Make sure the rear seat legs are relocked into place (folding down the seatback will disengage them) by pushing down- ward on the back of the seat. Adjust the seatback to the 1st lock position (most upright position) and then to the 5th lock position.

Make sure locked securely.

the seat and seatback

is

Canada only

Type A buttons)

(anchor position

indicated by

107

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Canada only

Canada only

Canada only

(anchor position

indicated by

Type B buttons)

(anchor position

indicated by

Type B tags)

(anchor position

indicated by

Type A tags)

108

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

3. Widen the slits of the seat cushion slightly and confirm the position of the lower anchorages near the but- tons or tags on the seatback. 4. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 102 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

’04 4Runner_U (L/O 0409)

CAUTION

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

(cid:1) After securing

the child restraint

system, never recline the seat.

(cid:1) Do not install a child restraint sys- tem on the second seat if it inter- feres with the lock mechanism of the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

(cid:1) When using the left side lower an- chorages for the child restraint sys- tem, do not sit in the center seat. The performance of the center seat belt cannot be brought out suffi- the belt may be ciently because the seat belt high- positioned or may be the risk of serious injury in the case of collision.

loose- fitting, posing

109

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

110

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

SECTION 1- 4

OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt steering wheel Tilt and telescopic steering wheel Outside rear view mirrors Anti- glare inside rear view mirror Auto anti- glare inside rear view mirror Rear side- view mirrors Sun visors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

112
112
113
115
116
117
117

111

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Tilt steering wheel

Tilt and telescopic steering wheel

CAUTION

(cid:1) Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

To change the steering wheel angle, hold the steering wheel, pull the lock release lever toward you, tilt the steer- ing wheel to the desired angle and re- lease the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.

112

ADJUSTMENT OF STEERING WHEEL TILT To change the steering wheel angle, hold the steering wheel, pull the lock release lever toward you, tilt the steer- ing wheel to the desired angle and re- lease the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Outside rear view mirrors—

CAUTION

(cid:1) Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

(cid:1) After adjusting the steering wheel, try moving it up and down or for- ward and rearward to make sure it is locked in position.

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror. On some models, when you push the back window defogger switch, the heater panels in the outside rear view mirrors will quickly clear the surface. (See “Back win- dow and outside rear view mirror defog- gers” on page 133 in Section 1- 5.)

113

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

OF

TELESCOPIC

ADJUSTMENT STEERING COLUMN To change the steering wheel length, push down the lock release lever, set the steering wheel to the desired length and return the lever to its original posi- tion.

On some models, the outside rear view mirrors are rain clearing mirrors that clear the driver’s rear view when it rains. (For details, see “Rain clearing mirrors” on page 345 in Section 5.)

CAUTION

(cid:1) Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.

(cid:1) On some models, since the mirror surfaces can get hot, do not touch them when the defogger switch is on.

114

’04 4Runner_U (L/O 0409)

—Power rear view mirror control

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de-icer to free the mirror.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch to “L” (left) or “R”

2. Control switch—To move

the mirror Push the switch in the desired direc- tion.

Mirrors can be adjusted when the key is in the “ACC” or “ON” position.

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

—Folding rear view mirrors

Anti- glare inside rear view mirror

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

The rear view mirrors can be folded backward for parking in compact areas. To fold the rear view mirror, push back- ward.

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

115

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Auto anti- glare inside rear view mirror

to reduce

In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off the automatic function, push the “MIRROR” switch. To turn on the automatic function again, push the “MIRROR” switch. Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it may take a little longer for the mirror to darken the detection of headlights.

in response

to

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

To ensure correct functioning of an anti- glare mirror sensor located on the back side of the mirror, do not touch or cover the sensor with your finger or a piece of cloth, etc.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti- glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.

ignition key

the

is

116

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

Rear side- view mirrors

Sun visors—

Rear side- view mirrors are useful as a secondary means of checking the area to the rear of the vehicle. Carefully check the area to the rear of the vehicle by either looking directly or using both outside and inside rear view mirrors.

Type A

Type B

117

2004 4RUNNER from Sep. ’04 Prod. (OM35847U)

’04 4Runner_U (L/O 0409)

CAUTION

(cid:1) Type A—Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover rear view mirror and obstruct the rear view.

the anti- glare

inside

(cid:1) Type B—Slide the main sun visor only when it is swung down to the lateral side. It can cover the anti- glare inside rear view mirror and obstruct the rear view.

To block the glare from the front when the main sun visor is swung to the lateral side, swing down the sub visor.

To block out glare, move the sun visor. To block out glare from the front—Swing down the main sun visor (position 1). To block out glare from the side—Swing down the main sun visor, remove it from the hook and swing it to the lateral side (position 2). Type A—If glare comes from obliquely be- hind you, extend the plate at the end of the visor (to position 3). Type B—If glare comes from obliquely be- hind you, slide the main sun visor back- ward (to position 3).