Instant Fuel Economy (3)
(cid:129) This mode displays the instant fuel
economy during the last few sec-
onds when the vehicle speed is
more than 6.2MPH(10km/h).
- Fuel economy range: 0.0 ~ 99.9
L/100km or 0.0 ~ 99.9 MPG
(Type A), 0.0 ~ 30.0 L/100km or
0.0 ~ 50.0 MPG (Type B, C)
Average Fuel Economy (2)
(cid:129) The average fuel economy is cal-
culated by the total driving dis-
tance and fuel consumption since
the last average fuel economy
reset.
- Fuel economy range: 0.0 ~ 99.9
MPG or L/100km
(cid:129) The average fuel economy can be reset both manually and automati- cally.
Manual reset
To clear the average fuel economy
manually, press the RESET button
(Type A : RESET, Type B, C :
) on
the steering wheel for more than 1
second when the average fuel econo-
my is displayed.
Automatic reset To make the average fuel economy be reset automatically whenever refu- eling, select the “Auto Reset” mode in User Setting menu of the LCD win- dow (Refer to “LCD window”). Under “Auto Reset” mode, the aver- age fuel economy will be cleared to zero (---) when the vehicle speed exceeds 1MPH after refueling more than 1.6 gallons(6 liters).
✽✽ NOTICE
The average fuel economy is not dis-
played for more accurate calculation
if the vehicle does not drive more
than 10 seconds or 50 meters (0.03
miles) since the ignition switch or
Engine Start/Stop button is turned
to ON.
62
YDM USA 4a.QXP 2016-05-03 17:26 Page 63
Trip A/B
■ Type A
■ Type B
(cid:129) To reset the tripmeter, press the RESET button (Type A : RESET, Type B, C : ) on the steering wheel for more than 1 second when the tripmeter is displayed.
■ Type C
OYDM046390N/OYDM046396
OYDM046392N
Tripmeter (1) (cid:129) The tripmeter is the total driving dis- tance since the last tripmeter reset. - Distance range: 0.0 ~ 9999.9 mi. or
km
Features of your vehicle
Average Vehicle Speed (2) (cid:129) The average vehicle speed is cal- culated by the total driving dis- tance and driving time since the last average vehicle speed reset. - Speed range: 0 ~ 999 MPH or km/h (cid:129) To reset the average vehicle speed, press the RESET button (Type A : RESET, Type B, C : ) on the steering wheel for more than 1 sec- ond when the average vehicle speed is displayed.
✽✽ NOTICE • The average vehicle speed is not dis- played if the driving distance is less than 0.03 miles (50 meters) or the driving time is less than 10 seconds since the ignition switch or Engine Start/Stop button is turned to ON.
• Even if the vehicle is not in motion, the average vehicle speed keeps going while the engine is running.
4 63
YDM USA 4a.QXP 2016-05-03 17:27 Page 64
Features of your vehicle
Elapsed Time (3)
(cid:129) The elapsed time is the total driv-
ing time since the last elapsed time
reset.
- Time range (hh:mm): 00:00 ~ 99:59
(cid:129) To reset the elapsed time, press
the RESET button (Type A :
RESET, Type B, C :
) on the
steering wheel for more than 1
second when the elapsed time is
displayed.
✽✽ NOTICE Even if the vehicle is not in motion, the elapsed time keeps going while the engine is running.
64
Digital speedometer
One time driving information mode
OYDM046394
This mode displays the current
speed of the vehicle.
OJFA045285
This display shows trip distance (1),
average fuel economy (2) and the
vehicle can be driven with the
remaining fuel (3).
This information is displayed for a
few seconds when you turn off the
engine and then goes off automati-
cally. The information provided is cal-
culated according to each trip.
If the estimated distance is below
1mi (1km), the distance to empty (3)
will display as "---" and a refuel mes-
sage will appear (4).
YDM USA 4a.QXP 2016-05-03 17:27 Page 65
LCD Modes (for Type B, C instrument cluster)
OYD046310L
(1) Trip Computer mode This mode displays driving informa- tion like the tripmeter, fuel economy, and so on. For more details, refer to “Trip Computer” in this chapter.
(2) Turn By Turn mode (if equipped) This mode displays the state of the navigation.
Features of your vehicle
Turn By Turn Mode (if equipped)
OYD046299
This mode displays the state of the
navigation.
(3) Audio mode (if equipped) This mode displays the state of the A/V system.
(4) Service mode This mode informs of service interval (mileage or days) and pressure sta- tus of each tire.
(5) Master warning mode This mode informs of warning mes- sages related to washer fluid or mal- function of Blind Spot Detection sys- tem (BSD) and so on.
(6) User Setting mode On this mode, you can change set- tings of the doors, lamps and so on.
❈ For controlling the LCD modes, refer to "LCD window Control" in this chapter.
4 65
YDM USA 4a.QXP 2016-05-03 17:27 Page 66
Features of your vehicle
A/V Mode (if equipped)
Service Mode
Service required
OYD046298
This mode displays the state of the
A/V system.
OYDNDI2059
Service in
It calculates and displays when you
need a scheduled maintenance
service (mileage or days).
If the remaining mileage or time
reaches 1,500 km (900 mi.) or 30
days, "Service in" message is dis-
played for several seconds each time
you set the ignition switch or Engine
Start/Stop Button to the ON position.
OYD046220L If you do not have your vehicle serv- iced according to the already inputted service interval, “Service required” message is displayed for several sec- onds each time you set the ignition switch or Engine Start/Stop Button to the ON position.
66
YDM USA 4a.QXP 2016-05-03 17:27 Page 67
To reset the service interval to the mileage and days you inputted before: - Press the SELECT/RESET button
for more than 1 second.
Features of your vehicle
User Settings Mode
OYD046210L On this mode, you can change set- ting of the doors, lamps, and so on.
4 67
OYD046218L
Service in OFF If the service interval is not set, “Service in OFF” message is dis- played on the LCD window.
✽✽ NOTICE If any of the following conditions occurs, the mileage and days may be incorrect. - The battery cable is disconnected. - The fuse switch is turned off. - The battery is discharged.
YDM USA 4a.QXP 2016-05-03 17:27 Page 68
Features of your vehicle
Driving Assist (if equipped) (cid:129) Lane Keeping Assist System (LKAS, if equipped) : To adjust the sensitivity of the Lane Keeping Assist System.
- Lane
Departure/Standard LKA/Activ LKA For more informa- tion, refer to the "Lane Keep Assist System" in chap ter 5.
(cid:129) Autonomous Emergency Braking system (AEB,if equipped) : To acti- vate or deactivate the Autonomous Emergency Braking (AEB).
information,
For more to "Autonomous Emergency Braking (AEB)" in chapter 5.
refer
68
Door (cid:129) Automatically Lock - Disable : The auto door lock opera-
tion will be deactivated.
- Enable on Speed : All doors will be automatically locked when the vehicle exceeds 9.3mph(15km/h).
speed
- Enable on Shift : All doors will be automatically locked if the auto- matic transaxle shift lever is shifted from the P (Park) position to the R (Reverse), N (Neutral), or D (Drive) position.
(cid:129) Forward Collision Warning (FCW, if equipped) : To adjust the initial warning alert time for Autonomous Emergency Braking system.
- Late/Normal/Early For more infor- to "Autonomous in
mation, refer Emergency Braking (AEB)" chapter 6.
(cid:129) Rear Collision Warning (RCW,if
equipped)
- Rear Cross Traffic Alert : To acti- vate or deactivate the Rear Cross Traffic Alert system.
For more information, refer to "Blind Spot Detection" in chapter 5.
- Blind Spot Detection sound : To activate or deactivate the Blind Spot Detection sound.
For more information, refer to "Blind Spot Detection" in chapter 5.
YDM USA 4a.QXP 2016-05-03 17:27 Page 69
(cid:129) Automatically Unlock - Disable : The auto door unlock
operation will be canceled.
- Vehicle Off : All doors will be auto- matically unlocked when the igni- tion key is removed from the igni- tion switch or the Engine Star/Stop button is set to the OFF position.
- On Shift to P : All doors will be automatically unlocked if the auto- matic transaxle shift lever is shifted to the P (Park) position.
(cid:129) Two Press Unlock - Off:
The two press unlock function will be deactivated. Therefore, all doors will unlock if the door is unlocked.
- On:
The driver’s door will unlock if the door is unlocked. When the door is unlocked again within 4 seconds, all doors will unlock.
Features of your vehicle
(cid:129) Horn Feedback (if equipped) - Off:
The Horn feedback operation will be deactivated.
- On:
After locking the door by pressing the lock button on the transmitter, if you press the lock button again within 4 seconds, the warning sound will operate once to indicate that all doors are locked. (cid:129) Smart Trunk (if equipped) To activate or deactivate the Smart Trunk system. For more details, refer to "Smart Trunk" in this chapter.
Light (cid:129) One Touch Turn Signal (if equipped) - Off: The one touch turn signal function
will be deactivated.
- 3, 5, 7 Flashes : The lane change signals will blink 3, 5, or 7 times when the turn signal lever is moved slightly.
For more details, refer to "Light" in this chapter. (cid:129) Head Lamp Delay (if equipped) - If this item checked, the head lamp
delay function will be activated.
(cid:129) Welcome Light (If equipped) - If this item checked, the welcome
light function will be activated.
4 69
YDM USA 4a.QXP 2016-05-03 17:27 Page 70
Features of your vehicle
Sound (cid:129) Cluster voice guide Vol.
(if equipped) : Adjust the cluster voice guide volume. (Level 0~3)
(cid:129) BSD (Blind Spot Detection) Sound
(if equipped)
If this item checked, the blind spot detection sound will be activated. For more details, refer to "Blind Spot Detection System" in chapter 5. (cid:129) Welcome Sound (if equipped) If this item checked, the welcome sound function will be activated.
70
Convenience (cid:129) Seat Easy Access(if equipped) - None : The seat easy access func-
tion is deactivated.
- Normal/Extended : When you turn off the engine, the driver’s seat will automatically move rearward short (Normal) or long (Extended) for you to enter or exit the vehicle more comfortably. If you change the Engine Start/Stop button from OFF posi- tion to the ACC, ON, or START position, the driver’s seat will return to the original position.
For more details, refer to "Driver Position Memory System" in chapter 3.
Service interval (if equipped) On this mode, you can activate the service interval function with mileage (km or mi.) and period (months). - Off : The service interval function
will be deactivated.
- On :You can set the service interval
(mileage and months).
For more details, refer to "Service Mode" in this chapter.
✽✽ NOTICE If it is not available to set service interval on your vehicle, we recom- mend that you consult an authorized Kia dealer.
YDM USA 4a.QXP 2016-05-03 17:27 Page 71
Warning messages Warning messages appear on the LCD to warn the driver. It is located in the center of the instrument cluster. The warning message may appear differently depending on the type of instrument cluster and some may not show the warning message at all. The warning message is shown in either symbol, symbol and text, or text type only. You can choose the preferred language (for Type B only) by selecting the User setting menu in LCD mode.
Other features (cid:129) Fuel Economy Auto Reset - Off : The average fuel economy will not reset automatically whenever refueling.
- After Ignition : The average fuel economy will reset automatically when driving.
- After Refueling : The average fuel economy will reset automatically when refueling.
(cid:129) Fuel Economy Unit Choose the preferred fuel economy unit. (cid:129) Temperature Unit Choose the preferred temperature unit. (cid:129) Language (if equipped) Choose preferred the language.
Features of your vehicle
Door Open (cid:129) It means that any door is open.
OYD046191
4 71
YDM USA 4a.QXP 2016-05-03 17:27 Page 72
Features of your vehicle
■ Type A
■ Type B
Turn on FUSE SWITCH (if equipped) (cid:129) This warning message illuminates if the fuse switch under the steer- ing wheel is OFF.
(cid:129) It means that you should turn the
fuse switch on.
For more details, refer to “Fuses” in chapter 7.
OYD046193
Trunk (tailgate) Open (cid:129) It means that the trunk (tailgate) is
open.
OYD046250L/OYD046197
Sunroof Open (if equipped) (cid:129) This warning is displayed if you turn off the engine when the sun- roof is open.
72
YDM USA 4a.QXP 2016-05-03 17:27 Page 73
Engine has overheated This warning message illuminates when the engine coolant tempera- ture is above 120°C (248°F). This means that the engine is overheated and may be damaged. If your vehicle is overheated, refer to “Overheating” in chapter 6.
Features of your vehicle
Shift to P (for smart key system and automatic transaxle) (cid:129) This warning message illuminates if you try to turn off the engine without the shift lever in P (Park) position. (cid:129) At this time, the Engine Start/Stop Button turns to the ACC position (If you press the Engine Start/Stop Button once more, it will turn to the ON position).
Press START button while turn steer- ing (for smart key system) (cid:129) This warning message illuminates if the steering wheel does not unlock normally when the Engine Start/Stop Button is pressed.
(cid:129) It means that you should press the Engine Start/Stop Button while turning the steering wheel right and left.
Low Key Battery (for smart key system) (cid:129) This warning message illuminates if the battery of the smart key is discharged when the Engine Start/Stop Button changes to the OFF position.
Steering wheel unlocked (for smart key system) (cid:129) This warning message illuminates if the steering wheel does not lock when the Engine Start/Stop Button changes to the OFF position.
4 73
YDM USA 4a.QXP 2016-05-03 17:27 Page 74
Features of your vehicle
Check Steering Wheel Lock System (for smart key system) (cid:129) This warning message illuminates if the steering wheel does not lock normally when the Engine Start/Stop Button changes to the OFF position.
Press brake pedal to start engine (for smart key system and automatic transaxle) (cid:129) This warning message illuminates if the Engine Start/Stop Button changes to the ACC position twice by pressing the button repeatedly without depressing the brake pedal. (cid:129) It means that you should depress the brake pedal to start the engine.
Press clutch pedal to start engine (for smart key system and manual transaxle) (cid:129) This warning message illuminates if the Engine Start/Stop Button changes to the ACC position twice by pressing the button repeatedly without depressing the clutch pedal. (cid:129) It means that you should depress the clutch pedal to start the engine.
Key not in vehicle (for smart key system) (cid:129) This warning message illuminates if the smart key is not in the vehicle when you press the Engine Start/Stop Button.
(cid:129) It means that you should always
have the smart key with you.
Key not detected (for smart key system) (cid:129) This warning message illuminates if the smart key is not detected when you press the Engine Start/Stop Button.
Press START button again (for smart key system) (cid:129) This warning message illuminates if you can not operate the Engine Start/Stop Button when there is a problem with the Engine Start/Stop Button system.
(cid:129) It means that you could start the engine by pressing the Engine Start/ Stop Button once more.
(cid:129) If the warning illuminates each time you press the Engine Start/Stop Button, we recommend that you have the vehicle inspected by an authorized Kia dealer.
74
YDM USA 4a.QXP 2016-05-03 17:27 Page 75
Press START button with smart key (for smart key system) (cid:129) This warning message illuminates if you press the Engine Start/Stop Button while the warning message “Key not detected” is illuminating. (cid:129) At this time, the immobilizer indica-
tor light blinks.
Check fuse “BRAKE SWITCH” (for smart key system and automatic transaxle/transmission) (cid:129) This warning message illuminates if the brake switch fuse is discon- nected.
(cid:129) It means that you should replace the fuse with a new one. If that is not possible, you can start the engine by pressing the Engine Start/Stop Button for 10 seconds in the ACC position.
Features of your vehicle
Shift to P or N to start engine (for smart key system and automatic transaxle) (cid:129) This warning message illuminates if you try to start the engine with the shift lever not in the P (Park) or N (Neutral) position.
Low Washer Fluid (if equipped) (cid:129) This warning message illuminates on the service reminder mode if the washer fluid level in the reser- voir is nearly empty.
(cid:129) It means that you should refill the
washer fluid.
✽✽ NOTICE You can start the engine with the shift lever in the N (Neutral) position. But, for your safety, we recommend that you start the engine with the shift lever in the P (Park) position.
Low Fuel (cid:129) This warning message illuminates
if the fuel tank is nearly empty. - When the low fuel level warning
light is illuminates.
Add fuel as soon as possible.
4 75
YDM USA 4a.QXP 2016-05-03 17:27 Page 76
Features of your vehicle
WARNING AND INDICATOR LIGHTS Warning lights
Air bag Warning Light
Seat Belt Warning Light
✽✽ NOTICE - Warning lights Make sure that all warning lights are OFF after starting the engine. If any light is still ON, this indicates a situation that needs attention.
This warning light informs the driver that the seat belt is not fastened. For more details, refer to the "Seat Belts" in chapter 3.
This warning light illuminates:
(cid:129) Once you set the ignition switch or
Engine Start/Stop Button to the ON
position.
- It illuminates for approximately 6
seconds and then goes off.
(cid:129) When there is a malfunction with
the SRS. In this case, have your vehicle inspected by an authorized Kia dealer.
76
YDM USA 4a.QXP 2016-05-03 17:27 Page 77
Features of your vehicle
Parking Brake & Brake Fluid Warning Light
This warning light illuminates:
(cid:129) Once you set the ignition switch or
Engine Start/Stop Button to the ON
position.
- It illuminates for approximately 3
seconds
- It remains on if the parking brake
is applied.
(cid:129) When the parking brake is applied. (cid:129) When the brake fluid level in the
reservoir is low. - If the warning light illuminates with the parking brake released, it indicates the brake fluid level in reservoir is low.
If the brake fluid level in the reservoir is low: 1.Drive carefully to the nearest safe
location and stop your vehicle.
2.With the engine stopped, check the brake fluid level immediately and add fluid as required (For more details, refer to "Brake Fluid" in chapter 7). Then check all brake components for fluid leaks. If any leak on the brake system is still found, the warning light remains on, or the brakes do not operate properly, do not drive the vehicle. In this case, have your vehicle towed to an authorized Kia dealer and inspected.
Dual-diagonal braking system Your vehicle is equipped with dual- diagonal braking systems. This means you still have braking on two wheels even if one of the dual sys- tems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the vehicle. Also, the vehicle will not stop in as short a distance with only a portion of the brake system working. If the brakes fail while you are driv- ing, shift to a lower gear for addition- al engine braking and stop the vehi- cle as soon as it is safe to do so.
4 77
YDM USA 4a.QXP 2016-05-03 17:27 Page 78
Features of your vehicle
Driving the vehicle with a warning light ON is dangerous. If the Parking Brake & Brake Fluid Warning Light illuminates with the parking brake released, it indicates that the brake fluid level is low. In this case, have your vehicle inspect- ed by an authorized Kia dealer.
78
Electronic Brake force Distribution (EBD) System Warning Light These two warning lights illuminate at the same time while driving: (cid:129) When the ABS and regular brake
system may not work normally. In this case, have your vehicle inspected by an authorized Kia dealer.
Anti-lock Brake System (ABS) Warning Light
This warning light illuminates:
(cid:129) Once you set the ignition switch or
Engine Start/Stop Button to the ON
position.
- It illuminates for approximately 3
seconds and then goes off.
(cid:129) When there is a malfunction with the ABS (The normal braking sys- tem will still be operational without the assistance of the anti-lock brake system). In this case, have your vehicle inspected by an authorized Kia dealer.
YDM USA 4a.QXP 2016-05-03 17:27 Page 79
Features of your vehicle
WARNING - ABS/Brake
Light
When both ABS and Parking Brake & Brake Fluid Warning Lights are on, the brake system will not work normally and you may experience an unexpected and dangerous situation during sudden braking thereby increas- ing the risk of a crash or injury. In this case, avoid high speed driving and abrupt braking. Have your vehicle inspected by an authorized Kia dealer as soon as possible.
✽✽ NOTICE - Electronic Brake force Distribution (EBD) System Warning Light
When the ABS Warning Light is on or both ABS and Parking Brake & Brake Fluid Warning Lights are on, the speedometer, odometer, or trip- meter may not work. Also, the EPS Warning Light may illuminate and the steering effort may increase or decrease. In this case, have your vehicle inspect- ed by an authorized Kia dealer as soon as possible.
Electronic Power Steering (EPS) Warning Light (if equipped)
This warning light illuminates: (cid:129) Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It remains on until the engine is
started.
(cid:129) When there is a malfunction with
the EPS. In this case, have your vehicle inspected by an authorized Kia dealer.
4 79
YDM USA 4a.QXP 2016-05-03 17:27 Page 80
Features of your vehicle
Malfunction Indicator Lamp (MIL)
This warning light illuminates: (cid:129) Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It remains on until the engine is
started.
(cid:129) When there is a malfunction with
the emission control system. In this case, have your vehicle inspected by an authorized Kia dealer.
80
Charging System Warning Light
This warning light illuminates: (cid:129) Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It remains on until the engine is
started.
(cid:129) When there is a malfunction with either the alternator or electrical charging system.
CAUTION - Gasoline
Engine
If the Malfunction Indicator Lamp (MIL) illuminates, poten- tial catalytic converter damage is possible which could result in loss of engine power. In this case, have your vehicle inspected by an authorized Kia dealer as soon as possible.
CAUTION - Malfunction
Indicator Lamp (MIL)
Driving with the Malfunction Indicator Lamp (MIL) on may cause damage to the emission control systems which could effect drivability and/or fuel economy.
YDM USA 4a.QXP 2016-05-03 17:27 Page 81
If there is a malfunction with either the alternator or electrical charging system: 1. Drive carefully to the nearest safe
location and stop your vehicle.
2. Turn the engine off and check the alternator drive belt for looseness or breakage. If the belt is adjusted properly, there may be a problem in the electrical charging system. In this case, have your vehicle inspected by an authorized Kia dealer as soon as possible.
Features of your vehicle
CAUTION - Engine damage
If the engine is not stopped immediately after the engine oil pressure warning light is illumi- nated and stays on while the engine is running, serious engine damage may result.
Engine Oil Pressure Warning Light
This warning light illuminates: (cid:129) Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It remains on until the engine is
started.
(cid:129) When the engine oil pressure is low.
If the engine oil pressure is low: 1. Drive carefully to the nearest safe
location and stop your vehicle.
2. Turn the engine off and check the engine oil level (For more details, refer to "Engine Oil" in section 7). If the level is low, add oil as required. If the warning light remains on after adding oil or if oil is not avail- able, have your vehicle inspected by an authorized Kia dealer as soon as possible.
4 81
Low Fuel Level Warning Light
This warning light illuminates: When the fuel tank is nearly empty.
If the fuel tank is nearly empty: Add fuel as soon as possible.
CAUTION - Low Fuel
Level
Driving with the Low Fuel Level warning light on or with the fuel level below can cause the engine to misfire and damage the catalytic converter (if equipped).
YDM USA 4a.QXP 2016-05-03 17:27 Page 82
Features of your vehicle
If the warning light stays on while the engine is running, there may be seri- ous engine damage. In this case, 1. Stop the vehicle as soon as it is
safe to do so.
2. Turn off the engine and check the oil level. If the oil level is low, fill the engine oil to the proper level.
3. Start the engine again. If the warn- ing light stays on after the engine is started, turn the engine off immediately. In this case, have your vehicle inspected by an authorized Kia dealer.
82
YDM USA 4a.QXP 2016-05-03 17:27 Page 83
Low Tire Pressure Warning Light
This warning light illuminates:
(cid:129) Once you set the ignition switch or
Engine Start/Stop Button to the ON
position.
- It illuminates for approximately 3
seconds and then goes off.
(cid:129) When one or more of your tires are
significantly underinflated. For more details, refer to "Tire Pressure Monitoring System (TPMS)" in chapter 6.
This warning light remains on after blinking for approximately 60 seconds or repeats blinking and off at the intervals of approximately 3 seconds: (cid:129) When there is a malfunction with
the TPMS. In this case, have your vehicle inspected by an authorized Kia dealer as soon as possible. For more details, refer to "Tire Pressure Monitoring System (TPMS)" in chapter 6.
Features of your vehicle
WARNING - Low tire pressure
(cid:129) Significantly low tire pressure makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances.
(cid:129) Continued driving or low pres- sure tires will cause the tires to overheat and fail.
The TPMS cannot alert you to severe and sudden tire damage caused by external factors. If you notice any vehicle instability, immediately take your foot off the accelerator pedal, apply the brakes gradually with light force, and slowly move to a safe position off the road.
4 83
YDM USA 4a.QXP 2016-05-03 17:27 Page 84
Features of your vehicle
Door Ajar Warning Light (if equipped)
Adaptive Front Lighting System (AFLS) Warning Light (if equipped)
AFLS
Washer Fluid Warning Light (if equipped)
you
This warning light blinks: (cid:129) Once
the Engine
Start/Stop Button to the ON posi-
tion.
- It illuminates for approximately 3
set
seconds and then goes off.
(cid:129) When there is a malfunction with
the AFLS.
This warning light illuminates: (cid:129) When the washer fluid level in the
reservoir is nearly empty. In this case, you should refill the washer fluid.
If there is a malfunction with the AFLS: 1. Drive carefully to the nearest safe
location and stop your vehicle.
2. Turn the engine off and restart the engine. If the warning light remains on, have your vehicle inspected by an authorized Kia dealer.
This warning light illuminates: When a door is not closed securely.
Trunk (tailgate) Open Warning Light (if equipped)
This warning light illuminates: When the trunk (tailgate) is not closed securely.
84
YDM USA 4a.QXP 2016-05-03 17:27 Page 85
Master Warning Mode (if equipped)
(cid:129) This warning light informs the driv-
er the following situations - Low washer fluid (if equipped) - Blind Spot Detection (BSD) mal-
function (if equipped)
- Service reminder and so on.
The Master Warning Light illumi- nates when more than one of the above warning situations occur. At this time, the LCD Modes Icon will change from ( If the warning situation is solved, the master warning light will be turned off and the LCD Modes Icon will be changed back to its previous icon ( ). (ex : refill the washer fluid)
) to (
).
Features of your vehicle
Indicator Lights
Electronic Stability
Control (ESC) Indicator
Light
This indicator light illuminates:
(cid:129) Once you set the ignition switch or
Engine Start/Stop Button to the ON
position.
- It illuminates for approximately 3
seconds and then goes off.
(cid:129) When there is a malfunction with
the ESC system. In this case, have your vehicle inspected by an authorized Kia dealer.
Electronic Stability
Control (ESC) OFF
Indicator Light
This indicator light illuminates:
(cid:129) Once you set the ignition switch or
Engine Start/Stop Button to the ON
position.
- It illuminates for approximately 3
seconds and then goes off.
(cid:129) When you deactivate the ESC sys- tem by pressing the ESC OFF but- ton.
For more details, refer to "Electronic Stability Control (ESC)" in chapter 5.
This indicator light blinks: While the ESC is operating.
For more details, refer to "Electronic Stability Control (ESC)" in chapter 5.
4 85
YDM USA 4a.QXP 2016-05-03 17:27 Page 86
Features of your vehicle
SPORT Mode Indicator Light (if equipped)
Immobilizer Indicator Light (Without Smart Key) (if equipped)
Immobilizer Indicator Light (With Smart Key) (if equipped)
This indicator light illuminates (cid:129) When you select "SPORT" mode
as drive mode.
For more details, refer to "Drive Mode Integrated Control System" in chapter 5.
ECO Mode Indicator Light (if equipped)
This indicator light illuminates: (cid:129) When the vehicle detects the immobilizer in your key properly while the ignition switch is ON. - At this time, you can start the
engine.
- The indicator light goes off after
starting the engine.
This indicator light illuminates: (cid:129) When you select “ECO” mode as
drive mode.
For more details, refer to “Drive Mode Integrated Control System” in chapter 5.
This indicator light blinks: (cid:129) When there is a malfunction with
the immobilizer system. In this case, have your vehicle inspected by an authorized Kia dealer.
86
This indicator light illuminates for up to 30 seconds: (cid:129) When the vehicle detects the smart key in the vehicle properly while the Engine Start/Stop Button is ACC or ON. - At this time, you can start the
engine.
- The indicator light goes off after
starting the engine.
This indicator light blinks for a few seconds: (cid:129) When the smart key is not in the
vehicle. - At this time, you can not start the
engine.
YDM USA 4a.QXP 2016-05-03 17:27 Page 87
Features of your vehicle
This indicator light illuminates for 2
seconds and goes off:
(cid:129) When the vehicle can not detect
the smart key which is in the vehi-
cle while the Engine Start/Stop
Button is ON.
In this case, have your vehicle
inspected by an authorized Kia
dealer.
This indicator light blinks: (cid:129) When the battery of the smart key
is weak. - At this time, you can not start the engine. However, you can start the engine if you press the Engine Start/Stop Button with the smart key. (For more details, refer to "Starting the Engine" in section 5).
(cid:129) When there is a malfunction with
the immobilizer system. In this case, have your vehicle inspected by an authorized Kia dealer.
Turn Signal Indicator Light
High Beam Indicator Light
This indicator light blinks: (cid:129) When you turn the turn signal light
on.
If any of the following occurs, there may be a malfunction with the turn signal system. In this case, have your vehicle inspected by an authorized Kia dealer.
- The indicator light does not blink
but illuminates.
- The indicator light blinks more
rapidly.
- The indicator light does not illumi-
nate at all.
This indicator light illuminates: (cid:129) When the headlights are on and in
the high beam position
(cid:129) When the turn signal lever is pulled
into the Flash-to-Pass position.
Light ON Indicator Light
This indicator light illuminates: (cid:129) When the tail lights or headlights
are on.
Front Fog Indicator Light (if equipped)
This indicator light illuminates: (cid:129) When the front fog lights are on.
4 87
YDM USA 4a.QXP 2016-05-03 17:27 Page 88
Features of your vehicle
Cruise Indicator Light (if equipped)
CRUISE
KEY OUT Indicator Light (if equipped)
KEY OUT
LKAS (Lane Keeping Assistant System) Indicator (if equipped)
This indicator light illuminates: (cid:129) When the cruise control system is
enabled.
When the ENGINE START/STOP button is in the ACC or ON position, if any door is open, the system checks for the smart key.
For more details, refer to "Cruise Control System" in chapter 5.
Cruise SET Indicator Light (if equipped)
SET
This indicator light illuminates: (cid:129) When the cruise control speed is set.
For more details, refer to "Cruise Control System" in chapter 5.
This indicator light blinks: When the smart key is not in the vehicle and any door is open with the ignition switch or Engine Start/Stop button in the ACC or ON position. - At this time, if you close all doors, the chime will also sound for approximately 5 seconds.
- The indicator will go off while the
vehicle is moving.
The LKAS indicator will illuminate when you turn the lane keeping assistant system on by pressing the LKAS button. If there is a problem with the system, the yellow LKAS indicator will illumi- nate. For more details, refer to "LKAS" in chapter 5.
88
YDM USA 4a.QXP 2016-05-03 17:27 Page 89
REARVIEW CAMERA (IF EQUIPPED)
Always keep the camera lens clean. If lens is covered with foreign matter, the camera may not operate normally. The rearview camera is not a substi- tute for proper and safe backing-up procedures. Always drive safely and use caution when backing up. The rearview camera may not display every object behind the vehicle.
OYDM046015
The rear view camera will activate
with the ignition switch on and the
shift lever in the R (Reverse) position.
Note- during initial start up, system may not display instantly due to the audio system booting up. 2 ~ 4 seconds may be required before displaying during initial reverse selection. This occurs when starting and immediately shifting to reverse. This system is a supplemental sys- tem that shows behind the vehicle through the UVO audio or navigation display backing-up.
Features of your vehicle
WARNING - Backing Up & Using Camera Never rely solely on the rear view camera when backing up. Prior to entering your vehicle always do a visual check of the area behind your vehicle, and before backing up be aware of your sur- roundings and supplement the rear view camera by looking over your shoulders and checking your rear view mirrors. Due to the difficulty of ensuring that the area behind you remains clear, always back up slowly and stop immediately if you even suspect that a person, and especially a child, might be behind you.
4 89
Headlight escort function (if equipped) The headlights (and/or taillights) will remain on for approximately 20 min- utes after the ignition key is removed or turned to the ACC or LOCK posi- tion. However, if the driver’s door is opened and closed, the headlights are turned off after 30 seconds. The headlights can be turned off by pressing the lock button on the trans- mitter (or smart key) twice or turning off the light switch from the headlight or Auto light position.
If the driver gets out of the vehicle through other doors (except driver's door), the battery saver function does not operate and the headlight escort function does not turn off automatically. Therefore, It causes the battery to be discharged. In this case, make sure to turn off the lamp before getting out of the vehicle. If the headlights are not working properly have your vehicle inspected by an authorized Kia dealer. Don't attempt to inspect or replace the wiring yourself to prevent mal- function.
YDM USA 4a.QXP 2016-05-03 17:27 Page 90
Features of your vehicle
LIGHTING Battery saver function (cid:129) The purpose of this feature is to prevent the battery from being dis- charged. The system automatically turns off the parking lights when the driver removes the ignition key and opens the driver-side door.
(cid:129) With this feature, the parking lights will turn off automatically if the driv- er parks on the side of the road at night. If necessary, to keep the lights on when the ignition key is removed, perform the following: 1) Open the driver-side door. 2) Turn the parking lights OFF and ON again using the light switch on the steering column.
90
YDM USA 4a.QXP 2016-05-03 17:27 Page 91
Lighting control
Parking light position (
Headlight position ( )
Features of your vehicle
OXM049110
The light switch has a Headlight and
a Parking light position.
To operate the lights, turn the knob at
the end of the control lever to one of
the following positions:
(1) OFF position
(2) Parking light position
(3) Headlight position
(4) Auto light / AFLS position
(if equipped)
OAM049041
When the light switch is in the park-
ing light position (1st position), the
tail, position, license and instrument
panel lights will turn ON.
OAM049042
When the light switch is in the head-
light position (2nd position) the head,
tail, position, license and instrument
panel lights will turn ON.
The ignition switch must be in the ON
position to turn on the headlights.
4 91
YDM USA 4a.QXP 2016-05-03 17:27 Page 92
Features of your vehicle
Auto light position (if equipped)
OYDDCO2042
When the light switch is in the AUTO
light position, the taillights and head-
lights will turn ON or OFF automati-
cally depending on the amount of
light outside the vehicle.
Never place anything over the sensor
(1) located on the instrument panel.
This will ensure better auto-light sys-
tem control.
Do not clean the sensor using a win-
dow cleaner, the cleaner may leave a
light film which could interfere with
sensor operation.
92
If your vehicle has window tint or other types of metallic coating on the front windshield, the Auto light sys- tem may not work properly.
High beam operation
OAM049044
To turn on the high beam headlights,
push the lever away from you. Pull it
back for low beams.
The high-beam indicator will light
when the headlight high beams are
switched on.
To prevent the battery from being
discharged, do not leave the lights
on for a prolonged time while the
engine is not running.
YDM USA 4a.QXP 2016-05-03 17:28 Page 93
WARNING - High beams
Do not use high beam when there are other vehicles. Using high beam could obstruct the other driver's vision.
OAM049043
To flash the headlights, pull the lever
towards you. It will return to the normal
(low-beam) position when released.
The headlight switch does not need to
be on to use this flashing feature.
Features of your vehicle
Turn signals and lane change signals
OAM049045
The ignition switch must be on for the
turn signals to function. To turn on
the turn signals, move the lever up or
down (A). The green arrow indicators
on the instrument panel indicate
which turn signal is operating. They
will self-cancel after a turn is com-
pleted. If the indicator continues to
flash after a turn, manually return the
lever to the OFF position.
To signal a lane change, move the
turn signal lever slightly and hold it in
position (B). The lever will return to
the OFF position when released.
4 93
YDM USA 4a.QXP 2016-05-03 17:28 Page 94
Features of your vehicle
If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement. If an indicator flash is abnormally quick or slow, a bulb may be burned out or have a poor electrical connec- tion in the circuit.
94
One-touch lane change function To activate an one-touch lane change function, move the turn sig- nal lever slightly and then release it. The lane change signals will blink 3, 5 or 7 times. You can choose one-touch lane change blinking function in "One touch turn lamp" of "User setting". Refer to "User setting" in chapter 4.
✽✽ NOTICE If an indicator flash is abnormally quick or slow, the bulb may be burned out or have a poor electrical connection in the circuit.
Front fog light (if equipped)
lights are used
OAM049046N Fog to provide improved visibility when visibility is poor due to fog, rain or snow, etc. The fog lights will turn on when the fog light switch (1) is turned to the on position after the headlights are turned on. To turn off the fog lights, turn the switch (1) to the off position. When in operation, the fog lights consume large amounts of vehicle electrical power. Only use the fog lights when visibility is poor.
YDM USA 4a.QXP 2016-05-03 17:28 Page 95
AFLS (Adaptive Front Lighting System) (if equipped)
OYDDCO2042
Adaptive front lighting system uses
the steering angle and vehicle
speed, to keep your field of vision
wide by swiveling and leveling the
headlamp.
Change the switch to the AUTO posi-
tion when the engine is running. The
adaptive front lighting system will
operate when the headlamp is ON.
To turn off the AFLS, change the
switch to other positions. After turn-
ing the AFLS off, headlamp swiveling
no longer occurs, but leveling oper-
ates continuously.
Features of your vehicle
Never place anything over the sen- sor(1) located on the instrument panel. This will ensure better auto- light system to turn on and off auto- matically. If the AFLS malfunction indicator comes on, the AFLS is not working properly. Drive to the nearest safe location and restart the engine. If the indicator continuously remains on, have system be checked by an authorized Kia dealer.
4 95
YDM USA 4a.QXP 2016-05-03 17:28 Page 96
Features of your vehicle
WIPERS AND WASHERS Front
Rear ( 5 Door, if equipped)
OAM049100L
A : Wiper speed control (front)
OAM049048N
· HI – High wiper speed · LO – Low wiper speed · INT – Intermittent wipe · OFF – Off · MIST – Single wipe
96
B : Intermittent control wipe time
adjustment
C : Wash with brief wipes (front)*
D : Rear wiper/washer control
/ON – Continuous wipe · · ---/INT – Intermittent wipe · O/OFF – Off
E : Wash with brief wipes (rear)
* : if equipped
Windshield wipers Operates as follows when the igni- tion switch is turned ON. MIST : For a single wiping cycle, push the lever upward and release it. The wipers will operate continuously if the lever is held in this position.
OFF : Wiper is not in operation INT : Wiper operates intermittently at the same wiping intervals. Use this mode in a light rain or mist. To vary the speed setting, turn the speed control knob.
LO : Normal wiper speed HI : Fast wiper speed
If there is a heavy accumulation of snow or ice on the windshield, defrost the windshield for about 10 minutes, or until the snow and/or ice is removed before using the windshield wipers to ensure proper operation.
YDM USA 4a.QXP 2016-05-03 17:28 Page 97
Windshield washers (front)
OYF049101
In the OFF position, pull the lever
gently toward you to spray washer
fluid on the windshield and to run the
wipers 1-3 cycles.
Use this function when the wind-
shield is dirty.
The spray and wiper operation will
continue until you release the lever. If
the washer does not work, check the
washer fluid level.
If the fluid level is not sufficient, you
add appropriate non-abrasive wind-
shield washer fluid to the washer
reservoir.
The reservoir filler neck is located in the front of the engine compartment on the passenger side.
CAUTION - Washer pump
To prevent possible damage to the washer pump, do not oper- ate the washer when the fluid reservoir is empty.
WARNING - Obscured visibility
Do not use the washer in freez- ing temperatures without first warming the windshield with the defrosters; the washer solu- tion could freeze on the wind- shield and obscure your vision.
Features of your vehicle
CAUTION - Wiper position When washing the vehicle, set the wiper switch in the off posi- tion to stop the auto wiper oper- ation. The wiper may operate and be damaged if the switch is set in the AUTO mode while washing the vehicle.
CAUTION - Wipers &
windshields
(cid:129) To prevent possible damage to the wipers or windshield, do not operate the wipers when the windshield is dry.
(cid:129) To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them. (cid:129) To prevent damage to the wiper arms and other compo- nents,do not attempt to move the wipers manually.
4 97
YDM USA 4a.QXP 2016-05-03 17:28 Page 98
Features of your vehicle
Rear window wiper and wash- er switch (5 door) (if equipped)
OAM049103N The rear window wiper and washer switch is located at the end of the wiper and washer switch lever. Turn the switch to desired position to operate the rear wiper and washer. ON - Normal wiper operation INT - Intermittent wipe OFF - Wiper is not in operation
98
OYD044500
Push the lever away from you to
spray rear washer fluid and to run the
rear wipers 1~3 cycles. The spray
and wiper operation will continue
until you release the lever.
YDM USA 4a.QXP 2016-05-03 17:28 Page 99
INTERIOR LIGHT Do not use the interior lights for extended periods when the engine is not running. It may cause battery discharge.
WARNING - Interior light
Do not use the interior lights when driving in the dark. The glare from the interior lights may obstruct your view and cause an accident.
Automatic turn off function (if equipped) The interior lights automatically turn off approximately 20 minutes after the ignition switch is turned off. If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage.
Features of your vehicle
Map lamp (if equipped) ■ Type A
■ Type B
OYDM046385
OYDM046384
Push the lens (1) to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a map
lamp at night or as a personal lamp for
the driver and front passenger.
4 99
YDM USA 4a.QXP 2016-05-03 17:28 Page 100
Features of your vehicle
(cid:129) DOOR (2) :
In the DOOR position, the map lamp and the room lamp come on when any door is opened regard- less of the ignition switch position. When doors are unlocked by the transmitter (or smart key), the map lamp and the room lamp come on for approximately 30 seconds as long as any door is not open. The map lamp and the room lamp go out gradually after approximate- ly 30 seconds if the door is closed. However, if the ignition switch is ON or all doors are locked, the map lamp and the room lamp will turn off immediately. If a door is opened with the ignition switch in the ACC or LOCK position, the map lamp and the room lamp stays on for about 20 minutes. However, if a door is opened with the ignition switch in the ON position, the map lamp and the room lamp stays on continuously. If the type B room lamp switch is OFF, it doesn't work.
100
(cid:129) OFF (3) : The lights turn off even if
the
lamp
a door is opened. is When turned ON by pressing the lens (1), the lamp does not turn off even if the switch (2) is in the OFF position.
(cid:129) ON (4) : The map lamp and the room lamp stay on at all times.
Room lamp
OMD040097
To turn the room lamp ON or OFF,
push the switch.
If your vehicle is not equipped with a
map lamp, the room lamp will also
turn on or off as follows.
- The room lamp comes on when a door is opened. The lamps go out after approximately 30 seconds. - The room lamp comes on for approximately 30 seconds when doors are unlocked with a trans- mitter or smart key as long as the doors are not opened.
YDM USA 4a.QXP 2016-05-03 17:28 Page 101
- The room lamp will stay on for approximately 20 minutes if a door is opened with the ignition switch in the ACC or LOCK/OFF position.
- The room lamp will stay on con- tinuously if the door is opened with the ignition switch in the ON position.
- The room lamp will go out imme- diately if the ignition switch is changed to the ON position or all doors are locked.
Luggage room lamp (cid:129) 4 Door
Features of your vehicle
The luggage lamp comes on as long as the trunk lid (tailgate) is open. To prevent unnecessary charging sys- tem drain, close the trunk lid (tail- gate) securely after using the lug- gage room.
(cid:129) 5 Door
OYDDCO2045
OYDDCO3237
The luggage room lamp comes on
when the trunk (tailgate) is opened.
4 101
YDM USA 4a.QXP 2016-05-03 17:28 Page 102
Features of your vehicle
Glove box lamp
Vanity mirror lamp (if equipped)
OYDECO2046CN The glove box lamp comes on when the glove box is opened. To prevent unnecessary charging system drain, close the glove box securely after use.
102
OLM049105
Push the switch to turn the light on or
off.
(cid:129)
: The lamp will turn on if this
button is pressed.
(cid:129)
: The lamp will turn off if this
button is pressed.
Always have the switch in the off position when the vanity mirror lamp is not in use. If the sunvisor is closed without turning the lamp off, it may discharge the battery or damage the sunvisor.
YDM USA 4a.QXP 2016-05-03 17:28 Page 103
WELCOME SYSTEM (IF EQUIPPED) Headlamp welcome When the headlight(light switch in the headlight or AUTO position) is on and all doors (and trunk/tailgate) are locked and closed, the headlight, position light and tail light will come on for 15 seconds if any of the below is performed. (cid:129) Without smart key system
- When the door unlock button is
pressed on the transmitter.
(cid:129) With the smart key system
- When the door unlock button is
pressed on the smart key.
At this time, if you press the door lock button (on the transmitter or smart key), the lights will turn off immediately.
Interior light welcome
When the interior light switch is in the
DOOR position and all doors (and
trunk/tailgate) are locked and closed,
the room lamp will come on for 30
seconds if any of the below is per-
formed.
(cid:129) Without smart key system
- When the door unlock button is
pressed on the transmitter.
(cid:129) With the smart key system
- When the door unlock button is
pressed on the smart key.
- When the button of the outside
door handle is pressed.
At this time, if you press the door lock button, the lamps will turn off imme- diately.
Features of your vehicle
Puddle lamp and pocket lamp (if equipped) When all doors are locked and closed, the puddle lamp and pocket lamp will come on for 15 seconds if any of the below is performed. (cid:129) With the smart key system
- When the door unlock button is
pressed on the smart key.
- When the button of the outside
door handle is pressed.
- When the vehicle is approached with the smart key in possession.
At this time, if you press the door lock button, the lamps will turn off imme- diately.
4 103
YDM USA 4a.QXP 2016-05-03 17:28 Page 104
Features of your vehicle
DEFROSTER
CAUTION - Conductors
To prevent damage to the con- ductors bonded to the inside surface of the rear window, never use sharp instruments or window cleaners containing abrasives to clean the window.
If you want to defrost and defog the front windshield, refer to "Windshield Defrosting and Defogging" in this section.
104
The rear window defroster automati-
cally turns off after approximately 20
minutes or when the ignition switch is
turned off. To turn off the defroster
manually, press the rear window
defroster button again.
Outside mirror defroster (if equipped) If your vehicle is equipped with the outside rearview mirror defrosters, they will operate at the same time you turn on the rear window defroster.
Front wiper deicer (if equipped) If your vehicle is equipped with the front wiper deicer, it will be operating at the same time you operate the front windshield defroster.
Rear window defroster ■ Type B ■ Type A
the
OYD046017L The defroster heats the window to remove frost, fog and thin ice from the interior and exterior of the rear window, while the engine is running. To activate rear window defroster, press the rear window defroster button located in the center facia switch panel. The indicator on the rear window defroster button illu- minates when the defroster is on. If there is heavy accumulation of snow on the rear window, brush it off before operating the rear defroster.
YDM USA 4a.QXP 2016-05-03 17:28 Page 105
MANUAL CLIMATE CONTROL SYSTEM
Features of your vehicle
1. Air conditioning button 2. Fan speed control knob