Login- Download PDF Manual
-
may cause a heat-induced fire.
4 35
YDM USA 4a.QXP 2016-05-03 17:25 Page 36
Features of your vehicle
WARNING - Unsecured
engine hood
Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could fly open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.
The support rod must be inserted completely into the hole whenever you inspect the engine compartment. This will prevent the hood from falling and possibly injuring you.
CAUTION
Before closing the hood,ensure that all obstructions are removed from the engine com- partment and surrounding body sheet metal. Closing the hood with an obstruction present could result in damage to the engine, sheet metal or the impacted objects.
36
YDM USA 4a.QXP 2016-05-03 17:25 Page 37
FUEL FILLER LID Opening the fuel filler lid
OYDDCO2024
1. Stop the engine. 2. To open the fuel filler lid, pull the
fuel filler lid opener up.
3. Pull open the fuel filler lid (1) out to
fully open.
4. To remove the cap turn the fuel
filler cap (2) counterclockwise.
5. Refuel as needed.
OYDDCO2023
The fuel filler lid must be opened from inside the vehicle by pulling up the fuel filler lid opener. If the fuel filler lid does not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved de-icer fluid (do not use radiator anti-freeze) or move the vehicle to a warm place and allow the ice to melt.Features of your vehicle
Closing the fuel filler lid 1. To install the cap, turn it clockwise until it "clicks" one time. This indi- cates that the cap is securely tight- ened.
2. Close the fuel filler lid and push it lightly and make sure that it is securely closed.
WARNING - Refueling
Always remove the fuel cap carefully and slowly. If the cap is venting fuel or if you hear a hissing sound, wait until the condition stops before com- pletely removing the cap. If pressurized fuel sprays out, it can cover your clothes or skin and subject you to the risk of fire and burns.
4 37
YDM USA 4a.QXP 2016-05-03 17:25 Page 38
Features of your vehicle
✽✽ NOTICE Tighten the cap until it clicks one time, otherwise the fuel cap open warning indicator light will illuminate.
Always check that the fuel cap is installed securely to prevent fuel spillage in the event of an accident.
WARNING - Fire /
explosion risk Read and follow all warnings posted at the gas station facili- ty. Failure to follow all warnings will result in severe personal injury, severe burns or death due to fire or explosion.
38
WARNING - Static
electricity
(cid:129) Before touching the fuel noz- zle, you should eliminate potentially dangerous static electricity discharge by touch- ing another metal part of the vehicle, a safe distance away from the fuel filler neck, noz- zle, or other gas source.
(cid:129) Do not get back into a vehicle once you have begun refuel- ing since you can generate static electricity by touching, rubbing or sliding against any item or fabric (polyester, satin, nylon, etc.) capable of produc- ing static electricity. Static electricity discharge can ignite fuel vapors resulting in rapid burning. If you must re- enter the vehicle, you should once again eliminate poten- tially dangerous static elec- tricity discharge by touching a metal part of the vehicle, away from the fuel filler neck, noz- zle or other gasoline source.
WARNING - Portable fuel
container
When using an approved portable fuel container, be sure to place the container on the ground prior to refueling. Static electricity dis- charge from the container can ignite fuel vapors causing a fire. Once refueling has begun, con- tact with the vehicle should be maintained until the filling is com- plete. Use only approved portable plastic fuel containers designed to carry and store gasoline.
WARNING - Cell phone
fires
Do not use cellular phones while refueling. Electric current and/or electronic interference from cel- lular phones can potentially ignite fuel vapors causing a fire.
YDM USA 4a.QXP 2016-05-03 17:25 Page 39
Features of your vehicle
Make sure to refuel your vehicle according to the "Fuel requirements" suggested in chapter 1. If the fuel filler cap requires replace- ment, use only a genuine Kia cap or the equivalent specified for your vehi- cle. An incorrect fuel filler cap can result in a serious malfunction of the fuel system or emission control sys- tem.
CAUTION - Exterior paint
Do not spill fuel on the exterior surfaces of the vehicle. Any type of fuel spilled on painted surfaces may damage the paint.
WARNING - Refueling& Vehicle fires
When refueling, always shut the engine off. Sparks produced by electrical components related to the engine can ignite fuel vapors causing a fire. Once refueling is complete, check to make sure the filler cap and filler door are securely closed, before starting the engine.
WARNING - Smoking
DO NOT use matches or a lighter and DO NOT SMOKE or leave a lit cigarette in your vehicle while at a gas station especially during refueling. Automotive fuel is highly flammable and can, when ignited, result in fire.
4 39
YDM USA 4a.QXP 2016-05-03 17:25 Page 40
Features of your vehicle
SUNROOF (IF EQUIPPED)
Sunroof open warning (if equipped)
■ Type A
In cold and wet climates, the sunroof may not work properly due to freez- ing conditions. After the vehicle is washed or in a rainstorm, be sure to wipe off any water that is on the sunroof before operating it. The sunroof cannot slide when it is in the tilt position nor can it be tilted while in an open or slide position.
OYDM046382
If your vehicle is equipped with a sunroof, you can slide or tilt your sunroof with the sunroof control lever located on the overhead console. The sunroof can only be opened, closed, or tilted when the ignition switch is in the ON position.CAUTION - Sunroof
control lever
Do not continue to press the sunroof control lever after the sunroof is fully opened,closed, or tilted.Damage to the motor or system components could occur.
CAUTION
To prevent damage to the sun- roof, periodically remove any dirt that may accumulate on the guide rail.
WARNING - Sunroof operation
When closing the sunroof, make sure there are no body parts in the movement range of the slid- ing roof. Parts of the body could become trapped or crushed.
40
■ Type B
OYDDDI2016
■ Type C
OYDNDI2030
OYDNDI2052
YDM USA 4a.QXP 2016-05-03 17:25 Page 41
Sliding the sunroof
If the driver removes the ignition key (smart key: turns off the engine) and opens the driver-side door when the sunroof is not fully closed, the warning chime will sound for a few seconds and a warning image will appear on the LCD display. Close the sunroof securely when leaving your vehicle.
OYDDCO2026
To open the sunroof automatically: Pull the sunroof control lever back- ward to the second detent position and then release it. The sunroof will slide all the way open. The sunroof will slide to the recom- mended open position (about 2in. (5
cm) before the maximum slide open position). To stop the sunroof sliding at any point, pull or push the sunroof control lever momentarily.Features of your vehicle
To open the sunroof to the maximum slide open position, press the switch towards the rear of the vehicle once again and hold it until the sunroof slide all the way open. To reduce wind noise while driving, we recommend you to drive at the recommended position (about 2in (5
cm) before the maximum slide open position).To close the sunroof automatically: Push the sunroof control lever for- ward to the second detent position and then release it. The sunroof will automatically close all the way. To stop the sunroof sliding at any point, pull or push the sunroof control lever momentarily. While driving with the sunroof in an open (or partially open position), your vehicle may demonstrate a wind buffeting or pulsation noise. This noise is a normal occurrence and can be reduced or eliminated by tak- ing the following actions. If you expe- rience the noise with the sunroof open, slightly reduce the size of the sunroof opening.
4 41
YDM USA 4a.QXP 2016-05-03 17:25 Page 42
Features of your vehicle
Automatic reversal
Tilting the sunroof
OYDDCO2027
To open the sunroof, push the sunroof control lever upward until the sunroof moves to the desired position. To close the sunroof, push the sunroof lever forward or pull downward until the sunroof moves to the desired position.OYF049215
If an object or part of the body is detected while the sunroof glass or sunshade is closing automatically, it will reverse the direction, and then stop. The auto reverse function does not work if a tiny obstacle is between the sliding glass or sunshade and the sunroof sash. You should always check that all passengers and objects are away from the sunroof before closing it.42
WARNING - Sunroof
Do not extend the face, neck, arms or body outside through the sunroof opening while driv- ing or operating the sunroof.
CAUTION - Sunroof
motor damage If you try to open the sunroof when the temperature is below freezing or when the sunroof is covered with snow or ice, the glass or the motor could be damaged.
YDM USA 4a.QXP 2016-05-03 17:25 Page 43
Sunshade
Resetting the sunroof Whenever the vehicle battery is dis- connected or discharged, or related fuse is blown, you must reset your sunroof system as follows:
✽✽ NOTICE Do not release the lever until the operation is completed. If you release the lever during oper- ation, try again from step 2.
Features of your vehicle
OBK049019
When opening the sunroof, the sun- shade will also open. Once the sun- roof is closed, the sunshade can be manually closed.6. Release the sunroof control lever after all operation has completed. (The sunroof system has been reset.)
❈ For more detailed information, contact an authorized Kia dealer.
✽✽ NOTICE If the sunroof is not reset when the vehicle battery is disconnected or discharged, or related fuse is blown, the sunroof may operate improperly.
1. Turn the ignition switch to the ON position or start the engine. We recommend resetting the sunroof while the engine is running.
2. Push and release the control lever forward in the direction of close repeatedly until the sunroof does not move. Sunroof will stop at the close position Glass will tilt up then will move up and down slightly.
3. Release the control lever when
sunroof does not move.
4. Glass will tilt up then will move up
and down slightly.
5. Within 5 seconds, push the sun- roof control lever forward in the direction of close until the sunroof operates as follows: Tilt down → Slide Open → Slide Close.
4 43
YDM USA 4a.QXP 2016-05-03 17:25 Page 44
Features of your vehicle
STEERING WHEEL Electric power steering (EPS) Power steering uses the motor to assist you in steering the vehicle. If the engine is off or if the power steer- ing system becomes inoperative, the vehicle may still be steered, but it will require increased steering effort. The electric power steering is con- trolled by the power steering control unit which senses the steering wheel torque and vehicle speed to com- mand the motor. The steering wheel becomes heavier as the vehicle’s speed increases and becomes lighter as the vehicle’s speed decreases for better control of the steering wheel. Should you notice any change in the effort required to steer during normal vehicle operation, have the power steering checked by an authorized Kia dealer.
44
✽✽ NOTICE The following symptoms may occur during normal vehicle operation: • The steering effort is increased immediately after turning the igni- tion switch on. This happens as the system performs the EPS system diagnostics. When the diagnostics are completed, the steering wheel will return to its normal condition • A click noise may be heard from the EPS relay after the ignition switch is turned to the ON or LOCK position.
• Motor noise may be heard when the vehicle is at a stop or at a low driving speed.
• The steering effort increases if the steering wheel is rotated continu- ously when the vehicle is not in motion. However, after a few min- utes, it will return to its normal condition.
• When you operate the steering wheel in low temperature, noise may occur. If the temperature rises, the noise will likely disap- pear. This is a normal condition.
(Continued)
(Continued) • When the charging system warn- ing light comes on or the battery voltage is low (when the alternator or battery does not operate nor- mally), the steering wheel may get heavy and become difficult to con- trol operate abnormally.
If the Electric Power Steering System does not operate normally, the warn- ing light will illuminate on the instru- ment cluster. The steering wheel may require increased steering effort. Take your vehicle to an authorized Kia dealer and have the vehicle checked as soon as possible.
YDM USA 4a.QXP 2016-05-03 17:26 Page 45
Tilt and telescoping steering Tilt steering allows you to adjust the steering wheel before you drive. You can also raise it to give your legs more room when you exit and enter the vehicle.
The steering wheel should be posi- tioned so that it is comfortable for you to drive, while permitting you to see the instrument panel warning lights and gauges.
WARNING - Steering wheel adjustment
Never adjust the angle and height of the steering wheel while driving. You may lose steering control
Features of your vehicle
Horn
OYDDCO3028
To change the steering wheel angle, pull down the lock release lever (1), adjust the steering wheel to the desired angle (2) and height (3), then pull up the lock-release lever to lock (4) the steering wheel in place. Be sure to adjust the steering wheel to the desired position before driving.OYDDCO2030
To sound the horn, press the horn symbol on your steering wheel. Check the horn regularly to be sure it operates properly. To sound the horn, press the area indicated by the horn symbol on your steering wheel (see illustration). The horn will operate only when this area is pressed.4 45
YDM USA 4a.QXP 2016-05-03 17:26 Page 46
Features of your vehicle
Heated steering wheel (if equipped)
OYDM046397
With the ignition switch in the ON position, pressing the heated steer- ing wheel button warms the steering wheel. The indicator on the button will illuminate and notify you on the LCD display. To turn the heated steering wheel off, press the button once again. The indicator on the button will turn off and notify you on the LCD display. If you turn on the ignition again after turning off your engine in half an hour (after operating heater button), the heating system will be main- tained in its 'on' condition.46
WARNING
If the steering wheel becomes too warm, turn the system off. The heated steering wheel may cause burns even at low tem- peratures, especially if used for long periods of time.
✽✽ NOTICE The heated steering wheel will turn off automatically approximately 30
minutes after the heated steering wheel is turned on.CAUTION
(cid:129) Do not install any grip to oper- ate the steering wheel. This causes damage to the heated steering wheel system.
(cid:129) When cleaning the heated steering wheel,do not use an organic solvent such as paint thinner, benzene, alcohol and gasoline. Doing so may dam- age the surface of the steering wheel.
(cid:129) If the surface of the steering wheel is damaged by a sharp object, damage to the heated steering wheel components could occur.
YDM USA 4a.QXP 2016-05-03 17:26 Page 47
FLEX STEER (5door, if equipped)
■ Type A
Normal mode
■ Type A
Features of your vehicle
OYDDCO2223
The FLEX STEER controls steering effort based upon driver's preference or road condition. You can select the desired steering mode by pressing the FLEX STEER button.■ Type B
OYDECO2233
■ Type B
OYDDCO2204
OYDDCO2207
The normal mode offers medium steering effort.OYDECO2232
When the steering mode button is pressed, the selected steering mode will appear on the LCD display. If the steering mode button is pressed within 4 seconds, the steering mode will change as shown above the pic- tures. If the steering mode button is not pressed for about 4 seconds, the LCD display will change to the previ- ous screen.4 47
YDM USA 4a.QXP 2016-05-03 17:26 Page 48
Features of your vehicle
Sport mode
■ Type A
Comfort mode
■ Type A
■ Type B
OYDDCO2206
■ Type B
OYDDCO2205
OYDDCO2208
The steering wheel becomes heav- ier. The sport mode is usually used when driving on the highway.OYDDCO2209
The steering wheel becomes lighter. The comfort mode is usually used when driving in the city or when park- ing the vehicle.48
For your safety, if you press the steering mode button while operating the steering wheel, the LCD display will change, but steering effort will not change immediately. After oper- ating the steering wheel, the steering effort will change automatically to the selected mode. Use caution when changing the steering mode while driving. When the electronic power steering is not operating, the flex steering wheel will not work.
YDM USA 4a.QXP 2016-05-03 17:26 Page 49
MIRRORS Inside rearview mirror Adjust the rearview mirror so that the center view through the rear window is seen. Make this adjustment before you start driving. Do not place objects in the rear seat which would interfere with your vision through the rear window.
WARNING - Mirror
adjustment
Do not adjust the rearview mirror while the vehicle is moving. This could result in loss of control.
Features of your vehicle
Electric chromic mirror (ECM) (if equipped) The electric rearview mirror automat- ically controls the glare from the headlights of the vehicles behind you in nighttime or low light driving condi- tions. The sensor mounted in the mir- ror senses the light level around the vehicle, and automatically controls the headlight glare from the vehicles behind you. When the engine is running, the glare is automatically controlled by the sensor mounted in the rearview mirror. Whenever the shift lever is shifted into reverse (R), the mirror will auto- matically go to the brightest setting in order to improve the drivers view behind the vehicle.
Day/night rearview mirror (if equipped)
Night
Day
OYDDCO2031
Make this adjustment before you start driving and while the day/night lever is in the day position. Pull the day/night lever toward you to reduce the glare from the headlights of the vehicles behind you during night driving. Remember that you lose some rearview clarity in the night position.
4 49
YDM USA 4a.QXP 2016-05-03 17:26 Page 50
Features of your vehicle
CAUTION - Cleaning
mirror
When cleaning the mirror,use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror. It may cause the liquid cleaner to enter the mirror housing which may damage the mirror.
50
Outside rearview mirror Be sure to adjust mirror angles before driving. Your vehicle is equipped with both left-hand and right-hand outside rearview mirrors. The mirrors can be adjusted remotely with the remote switch (if equipped). The mirror heads can be folded to prevent damage dur- ing an automatic car wash or when passing through a narrow street. The right outside rearview mirror is convex. Objects seen in the mirror are closer than they appear. Use your interior rearview mirror or direct observation to determine the actual distance of following vehicles when changing lanes.
Indicator
Sensor
OYDM046383
To operate the electric rearview mirror: (cid:129) The mirror defaults to the ON posi- tion whenever the ignition switch is turned on.
(cid:129) Press the ON/OFF button (1) to turn the automatic dimming func- tion off. The mirror indicator light will turn off. Press the ON/OFF button (1) to turn the automatic dimming func- tion on. The mirror indicator light will illuminate.
YDM USA 4a.QXP 2016-05-03 17:26 Page 51
CAUTION - Rearview
mirror
Do not scrape ice off the mirror face;this may damage the sur- face of the glass. If ice should restrict movement of the mirror, do not force the mirror for adjustment.To remove ice, use a deicer spray, or a sponge or soft cloth with very warm water.
WARNING - Mirror
adjustment
Do not adjust or fold the outside rearview mirrors while the vehi- cle is moving. This could result in loss of control.
Remote control
OYDM046403N
Electric type The electric remote control mirror switch allows you to adjust the posi- tion of the left and right outside rearview mirrors. To adjust the posi- tion of either mirror the ignition switch should be in the ACC or ON position. Move the lever (1) to R or L to select the right side mirror or the left side mirror, then press a corresponding point on the mirror adjustment con- trol to position the selected mirror up, down, left or right. After the adjustment, put the lever into neutral (center) position to pre- vent inadvertent adjustment.
Features of your vehicle
CAUTION - Outside mirror (cid:129) The mirrors stop moving when they reach the maximum adjusting angles, but the motor continues to operate while the switch is pressed. Do not press the switch longer than necessary, the motor may be damaged.
(cid:129) Do not attempt to adjust the outside rearview mirror by hand. Doing so may damage the parts.
4 51
YDM USA 4a.QXP 2016-05-03 17:26 Page 52
Features of your vehicle
Folding the outside rearview mirror
OYDDCO2041
Electric type The outside rearview mirror can be folded or unfolded by pressing the switch as below. Left (1) : The mirrors will unfold. Right (2) : The mirrors will fold.
52
Center (AUTO, 3) : The mirror will fold or unfold auto- matically as follows: (cid:129) Without smart key system
- The mirrors will fold or unfold when the door is locked or unlocked by the transmitter.
(cid:129) With smart key system
- The mirrors will fold or unfold when the door is locked or unlocked by the smart key.
- The mirrors will fold or unfold when the door is locked or unlocked by the button on the outside door handle.
- The mirrors will unfold when you approach the vehicle (all doors closed and locked) with a smart key in possession. (if equipped)
CAUTION - Electric type
outside rearview mirror The electric type outside rearview mirror operates even though the ignition switch is in the OFF position. However, to prevent unnecessary battery discharge, do not adjust the mirrors longer than necessary while the engine is not running. Do not attempt to fold the elec- tric type outside rearview mirror by hand because doing so could cause motor damage or failure.
YDM USA 4a.QXP 2016-05-03 17:26 Page 53
Features of your vehicle
OYDDCO2040
Manual type To fold outside rearview mirror, grasp the housing of mirror and then fold it toward the rear of the vehicle.
4 53
YDM USA 4a.QXP 2016-05-03 17:26 Page 54
Features of your vehicle
INSTRUMENT CLUSTER ■■ Type A / Type B
■■ Type C
54
1. Tachometer
2. Speedometer
3. Engine coolant temperature gauge
4. Fuel gauge
5. Turn signal indicators
6. Warning and indicator lights
7. LCD window
❈ The actual cluster in the vehicle may differ
from the illustration. For more details refer to the "Gauges" in the next pages.
OYDM046404/OYDM046375N
YDM USA 4a.QXP 2016-05-03 17:26 Page 55
Instrument Cluster Control Adjusting Instrument Cluster Illumination
■ Type A
■ Type B
(cid:129) If the brightness reaches to the maximum or minimum level, an alarm will sound.
Features of your vehicle
■ Type C
OYDDDI2011/OYDEDI2020
OYDM046398
The instrument panel illumination intensity can be adjusted by pressing the control switch with the headlight switch in any position when the igni- tion switch is in the ON position. The illumination intensity is shown on the instrument cluster LCD win- dow.
OYDEDI2034
(cid:129) If you hold the illumination control button ("+" or "-"), the brightness will be changed continuously.4 55
YDM USA 4a.QXP 2016-05-03 17:26 Page 56
Features of your vehicle
LCD window Control
■ Type A
■ Type B
OYDDDI2018
The LCD window modes can be changed by using the control buttons on the steering wheel.[Type A] (1) TRIP : TRIP button for changing
trip modes
(2) RESET : RESET button for reset-
ting items
56
[Type B] (1)
(2)
(3)
: MODE button for changing modes : MOVE button for changing items : SELECT/RESET button for setting or the selected item
resetting
Gauges Speedometer ■ Type A, B
❈ For the LCD modes, refer to "LCD
window" in this chapter.
■ Type C
OYDEDI2003R
OYDEDI2004R The speedometer indicates the for- ward speed of the vehicle. The speedometer is calibrated in miles per hour and/or kilometers per hour.
YDM USA 4a.QXP 2016-05-03 17:26 Page 57
The tachometer pointer may move slightly when the ignition switch is in ACC or ON position with the engine OFF. This movement is normal and will not affect the accuracy of the tachometer once the engine is run- ning.
CAUTION - Red zone
Do not operate the engine with- in the tachometer's RED ZONE. This may cause severe engine damage.
Tachometer
■ Type A, B
■ Type C
OYDDDI2005
OYDDDI2006
indicates
tachometer
The the approximate number of engine revo- lutions per minute (rpm). Use the tachometer to select the cor- rect shift points and to prevent lug- ging and/or over-revving the engine.
Features of your vehicle
Engine coolant temperature gauge
■ Type A, B
■ Type B
OYDDDI2007/OYDDDI2008
This gauge shows the temperature of the engine coolant when the igni- tion switch is ON. Do not continue driving with an over- heated engine. If your vehicle over- heats, refer to "If the engine over- heats" in chapter 6. If the gauge pointer moves beyond the normal range area toward the "H" position, it indicates overheating that may damage the engine.4 57
YDM USA 4a.QXP 2016-05-03 17:26 Page 58
Features of your vehicle
Fuel gauge
■ Type A, B
■ Type C
OYDDDI2009
OYDDDI2010
The fuel gauge indicates the approx- imate amount of fuel remaining in the fuel tank. The fuel tank capacity is given in chapter 8. The fuel gauge is supplemented by a low fuel warning light, which will illuminate when the fuel tank is nearly empty. 58
On inclines or curves, the fuel gauge pointer may fluctuate or the low fuel warning light may come on earlier than usual due to the movement of fuel in the tank.
✽✽ NOTICE - Fuel gauge Running out of fuel can expose vehi- cle occupants to danger. You must stop and obtain additional fuel as soon as possible after the warning light comes on or when the gauge indicator comes close to the "E (Empty)" level.
CAUTION - Low fuel
Avoid driving with extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.
Odometer
■ Type A
■ Type B
■ Type C
OYDNDI2902/OYDNDI2904
OYDNDI2906
Odometer The odometer indicates the total dis- tance the vehicle has been driven. You will also find the odometer useful to determine when periodic mainte- nance should be performed.
YDM USA 4a.QXP 2016-05-03 17:26 Page 59
Transaxle Shift Indicator Automatic Transaxle Shift Indicator (if equipped) ■ Type B ■ Type A
(cid:129) Park : P (cid:129) Reverse : R (cid:129) Neutral : N (cid:129) Drive : D (cid:129) Sports Mode : 1, 2, 3, 4, 5, 6
■ Type C
OYD046244L/OYD046245L
OYDM046376
This indicator displays which auto- matic transaxle shift lever is selected.
Features of your vehicle
Manual transaxle shift indicator (if equipped)
This indicator informs you which gear is desired while driving to save fuel. For example
: Indicates that shifting up to the 3rd gear is desired (currently the shift lever is in the 2nd gear).
: Indicates that shifting down to the 3rd gear is desired (current- ly the shift lever is in the 4th gear).
✽✽ NOTICE When the system is not working properly, up & down arrow indica- tor and Gear are not displayed.
4 59
YDM USA 4a.QXP 2016-05-03 17:26 Page 60
Features of your vehicle
LCD WINDOWS (IF EQUIPPED) Over view
■ Type A
■ Type B
OYDM046395
■ Type C
OYD046307L
OYDM04630
60
LCD windows show the following var- ious information to drivers. - Trip information - LCD modes (for Type B, C) - Warning messages (for Type B, C)
Trip information (Trip computer) The trip computer is a microcomput- er-controlled driver information sys- tem that displays information related to driving.
✽✽ NOTICE Some driving information stored in the trip computer (for example Average Vehicle Speed) resets if the battery is disconnected.
Trip Modes
FUEL ECONOMY
(cid:129) Distance To Empty (cid:129) Average Fuel Economy (cid:129) Instant Fuel Economy
TRIP A
(cid:129) Tripmeter [A] (cid:129) Average Vehicle Speed [A] (cid:129) Elapsed Time [A]
TRIP B
(cid:129) Tripmeter [B] (cid:129) Average Vehicle Speed [B] (cid:129) Elapsed Time [B]
Digital speedometer
(for Type B,C)
YDM USA 4a.QXP 2016-05-03 17:26 Page 61
Type A To change the trip mode, press the “TRIP” button.
Fuel Economy
■ Type A
■ Type B
Type B To change the trip mode, press the MOVE button ▼.
■ Type C
OYDM046386N/OYDNDI2033
OYDM046389N
Distance To Empty (1) (cid:129) The range is the estimated dis- tance the vehicle can be driven with the remaining fuel.
Features of your vehicle
- Distance range : 30 ~ 9999 mi or
50 ~ 9999 km.
(cid:129) If the estimated distance is below 30 mi. (50 km), the trip computer will display "---" as distance to empty.
✽✽ NOTICE • If the vehicle is not on level ground or the battery power has been interrupted, the distance to empty function may not operate correct- ly.
• The distance to empty may differ from the actual driving distance as it is an estimate of the available driving distance.
• The trip computer may not regis- ter additional fuel if less than 6
liters (1.6 gallons) of fuel are added to the vehicle.• The fuel economy and distance to empty may vary significantly based on driving conditions, driv- ing habits, and condition of the vehicle.
4 61
YDM USA 4a.QXP 2016-05-03 17:26 Page 62
Features of your vehicle
Instant Fuel Economy (3) (cid:129) This mode displays the instant fuel economy during the last few sec- onds when the vehicle speed is more than 6.2MPH(10km/h). - Fuel economy range: 0.0 ~ 99.9
L/100km or 0.0 ~ 99.9 MPG (Type A), 0.0 ~ 30.0 L/100km or 0.0 ~ 50.0 MPG (Type B, C)Average Fuel Economy (2) (cid:129) The average fuel economy is cal- culated by the total driving dis- tance and fuel consumption since the last average fuel economy reset. - Fuel economy range: 0.0 ~ 99.9
MPG or L/100km
(cid:129) The average fuel economy can be reset both manually and automati- cally.
Manual reset To clear the average fuel economy manually, press the RESET button (Type A : RESET, Type B, C : ) on the steering wheel for more than 1
second when the average fuel econo- my is displayed.Automatic reset To make the average fuel economy be reset automatically whenever refu- eling, select the “Auto Reset” mode in User Setting menu of the LCD win- dow (Refer to “LCD window”). Under “Auto Reset” mode, the aver- age fuel economy will be cleared to zero (---) when the vehicle speed exceeds 1MPH after refueling more than 1.6 gallons(6 liters).
✽✽ NOTICE The average fuel economy is not dis- played for more accurate calculation if the vehicle does not drive more than 10 seconds or 50 meters (0.03
miles) since the ignition switch or Engine Start/Stop button is turned to ON.62
YDM USA 4a.QXP 2016-05-03 17:26 Page 63
Trip A/B
■ Type A
■ Type B
(cid:129) To reset the tripmeter, press the RESET button (Type A : RESET, Type B, C : ) on the steering wheel for more than 1 second when the tripmeter is displayed.
■ Type C
OYDM046390N/OYDM046396
OYDM046392N
Tripmeter (1) (cid:129) The tripmeter is the total driving dis- tance since the last tripmeter reset. - Distance range: 0.0 ~ 9999.9 mi. or
km
Features of your vehicle
Average Vehicle Speed (2) (cid:129) The average vehicle speed is cal- culated by the total driving dis- tance and driving time since the last average vehicle speed reset. - Speed range: 0 ~ 999 MPH or km/h (cid:129) To reset the average vehicle speed, press the RESET button (Type A : RESET, Type B, C : ) on the steering wheel for more than 1 sec- ond when the average vehicle speed is displayed.
✽✽ NOTICE • The average vehicle speed is not dis- played if the driving distance is less than 0.03 miles (50 meters) or the driving time is less than 10 seconds since the ignition switch or Engine Start/Stop button is turned to ON.
• Even if the vehicle is not in motion, the average vehicle speed keeps going while the engine is running.
4 63
YDM USA 4a.QXP 2016-05-03 17:27 Page 64
Features of your vehicle
Elapsed Time (3) (cid:129) The elapsed time is the total driv- ing time since the last elapsed time reset. - Time range (hh:mm): 00:00 ~ 99:59
(cid:129) To reset the elapsed time, press the RESET button (Type A : RESET, Type B, C : ) on the steering wheel for more than 1
second when the elapsed time is displayed.✽✽ NOTICE Even if the vehicle is not in motion, the elapsed time keeps going while the engine is running.
64
Digital speedometer
One time driving information mode
OYDM046394
This mode displays the current speed of the vehicle.OJFA045285
This display shows trip distance (1), average fuel economy (2) and the vehicle can be driven with the remaining fuel (3). This information is displayed for a few seconds when you turn off the engine and then goes off automati- cally. The information provided is cal- culated according to each trip. If the estimated distance is below 1mi (1km), the distance to empty (3) will display as "---" and a refuel mes- sage will appear (4).YDM USA 4a.QXP 2016-05-03 17:27 Page 65
LCD Modes (for Type B, C instrument cluster)
OYD046310L
(1) Trip Computer mode This mode displays driving informa- tion like the tripmeter, fuel economy, and so on. For more details, refer to “Trip Computer” in this chapter.
(2) Turn By Turn mode (if equipped) This mode displays the state of the navigation.
Features of your vehicle
Turn By Turn Mode (if equipped)
OYD046299
This mode displays the state of the navigation.(3) Audio mode (if equipped) This mode displays the state of the A/V system.
(4) Service mode This mode informs of service interval (mileage or days) and pressure sta- tus of each tire.
(5) Master warning mode This mode informs of warning mes- sages related to washer fluid or mal- function of Blind Spot Detection sys- tem (BSD) and so on.
(6) User Setting mode On this mode, you can change set- tings of the doors, lamps and so on.
❈ For controlling the LCD modes, refer to "LCD window Control" in this chapter.
4 65
YDM USA 4a.QXP 2016-05-03 17:27 Page 66
Features of your vehicle
A/V Mode (if equipped)
Service Mode
Service required
OYD046298
This mode displays the state of the A/V system.OYDNDI2059
Service in It calculates and displays when you need a scheduled maintenance service (mileage or days). If the remaining mileage or time reaches 1,500 km (900 mi.) or 30
days, "Service in" message is dis- played for several seconds each time you set the ignition switch or Engine Start/Stop Button to the ON position.OYD046220L If you do not have your vehicle serv- iced according to the already inputted service interval, “Service required” message is displayed for several sec- onds each time you set the ignition switch or Engine Start/Stop Button to the ON position.
66
YDM USA 4a.QXP 2016-05-03 17:27 Page 67
To reset the service interval to the mileage and days you inputted before: - Press the SELECT/RESET button
for more than 1 second.
Features of your vehicle
User Settings Mode
OYD046210L On this mode, you can change set- ting of the doors, lamps, and so on.
4 67
OYD046218L
Service in OFF If the service interval is not set, “Service in OFF” message is dis- played on the LCD window.
✽✽ NOTICE If any of the following conditions occurs, the mileage and days may be incorrect. - The battery cable is disconnected. - The fuse switch is turned off. - The battery is discharged.
YDM USA 4a.QXP 2016-05-03 17:27 Page 68
Features of your vehicle
Driving Assist (if equipped) (cid:129) Lane Keeping Assist System (LKAS, if equipped) : To adjust the sensitivity of the Lane Keeping Assist System.
- Lane
Departure/Standard LKA/Activ LKA For more informa- tion, refer to the "Lane Keep Assist System" in chap ter 5.
(cid:129) Autonomous Emergency Braking system (AEB,if equipped) : To acti- vate or deactivate the Autonomous Emergency Braking (AEB).
information,
For more to "Autonomous Emergency Braking (AEB)" in chapter 5.
refer
68
Door (cid:129) Automatically Lock - Disable : The auto door lock opera-
tion will be deactivated.
- Enable on Speed : All doors will be automatically locked when the vehicle exceeds 9.3mph(15km/h).
speed
- Enable on Shift : All doors will be automatically locked if the auto- matic transaxle shift lever is shifted from the P (Park) position to the R (Reverse), N (Neutral), or D (Drive) position.
(cid:129) Forward Collision Warning (FCW, if equipped) : To adjust the initial warning alert time for Autonomous Emergency Braking system.
- Late/Normal/Early For more infor- to "Autonomous in
mation, refer Emergency Braking (AEB)" chapter 6.
(cid:129) Rear Collision Warning (RCW,if
equipped)
- Rear Cross Traffic Alert : To acti- vate or deactivate the Rear Cross Traffic Alert system.
For more information, refer to "Blind Spot Detection" in chapter 5.
- Blind Spot Detection sound : To activate or deactivate the Blind Spot Detection sound.
For more information, refer to "Blind Spot Detection" in chapter 5.
YDM USA 4a.QXP 2016-05-03 17:27 Page 69
(cid:129) Automatically Unlock - Disable : The auto door unlock
operation will be canceled.
- Vehicle Off : All doors will be auto- matically unlocked when the igni- tion key is removed from the igni- tion switch or the Engine Star/Stop button is set to the OFF position.
- On Shift to P : All doors will be automatically unlocked if the auto- matic transaxle shift lever is shifted to the P (Park) position.
(cid:129) Two Press Unlock - Off:
The two press unlock function will be deactivated. Therefore, all doors will unlock if the door is unlocked.
- On:
The driver’s door will unlock if the door is unlocked. When the door is unlocked again within 4 seconds, all doors will unlock.
Features of your vehicle
(cid:129) Horn Feedback (if equipped) - Off:
The Horn feedback operation will be deactivated.
- On:
After locking the door by pressing the lock button on the transmitter, if you press the lock button again within 4 seconds, the warning sound will operate once to indicate that all doors are locked. (cid:129) Smart Trunk (if equipped) To activate or deactivate the Smart Trunk system. For more details, refer to "Smart Trunk" in this chapter.
Light (cid:129) One Touch Turn Signal (if equipped) - Off: The one touch turn signal function
will be deactivated.
- 3, 5, 7 Flashes : The lane change signals will blink 3, 5, or 7 times when the turn signal lever is moved slightly.
For more details, refer to "Light" in this chapter. (cid:129) Head Lamp Delay (if equipped) - If this item checked, the head lamp
delay function will be activated.
(cid:129) Welcome Light (If equipped) - If this item checked, the welcome
light function will be activated.
4 69
YDM USA 4a.QXP 2016-05-03 17:27 Page 70
Features of your vehicle
Sound (cid:129) Cluster voice guide Vol.
(if equipped) : Adjust the cluster voice guide volume. (Level 0~3)
(cid:129) BSD (Blind Spot Detection) Sound
(if equipped)
If this item checked, the blind spot detection sound will be activated. For more details, refer to "Blind Spot Detection System" in chapter 5. (cid:129) Welcome Sound (if equipped) If this item checked, the welcome sound function will be activated.
70
Convenience (cid:129) Seat Easy Access(if equipped) - None : The seat easy access func-
tion is deactivated.
- Normal/Extended : When you turn off the engine, the driver’s seat will automatically move rearward short (Normal) or long (Extended) for you to enter or exit the vehicle more comfortably. If you change the Engine Start/Stop button from OFF posi- tion to the ACC, ON, or START position, the driver’s seat will return to the original position.
For more details, refer to "Driver Position Memory System" in chapter 3.
Service interval (if equipped) On this mode, you can activate the service interval function with mileage (km or mi.) and period (months). - Off : The service interval function
will be deactivated.
- On :You can set the service interval
(mileage and months).
For more details, refer to "Service Mode" in this chapter.
✽✽ NOTICE If it is not available to set service interval on your vehicle, we recom- mend that you consult an authorized Kia dealer.
YDM USA 4a.QXP 2016-05-03 17:27 Page 71
Warning messages Warning messages appear on the LCD to warn the driver. It is located in the center of the instrument cluster. The warning message may appear differently depending on the type of instrument cluster and some may not show the warning message at all. The warning message is shown in either symbol, symbol and text, or text type only. You can choose the preferred language (for Type B only) by selecting the User setting menu in LCD mode.
Other features (cid:129) Fuel Economy Auto Reset - Off : The average fuel economy will not reset automatically whenever refueling.
- After Ignition : The average fuel economy will reset automatically when driving.
- After Refueling : The average fuel economy will reset automatically when refueling.
(cid:129) Fuel Economy Unit Choose the preferred fuel economy unit. (cid:129) Temperature Unit Choose the preferred temperature unit. (cid:129) Language (if equipped) Choose preferred the language.
Features of your vehicle
Door Open (cid:129) It means that any door is open.
OYD046191
4 71
YDM USA 4a.QXP 2016-05-03 17:27 Page 72
Features of your vehicle
■ Type A
■ Type B
Turn on FUSE SWITCH (if equipped) (cid:129) This warning message illuminates if the fuse switch under the steer- ing wheel is OFF.
(cid:129) It means that you should turn the
fuse switch on.
For more details, refer to “Fuses” in chapter 7.
OYD046193
Trunk (tailgate) Open (cid:129) It means that the trunk (tailgate) is
open.
OYD046250L/OYD046197
Sunroof Open (if equipped) (cid:129) This warning is displayed if you turn off the engine when the sun- roof is open.
72
YDM USA 4a.QXP 2016-05-03 17:27 Page 73
Engine has overheated This warning message illuminates when the engine coolant tempera- ture is above 120°C (248°F). This means that the engine is overheated and may be damaged. If your vehicle is overheated, refer to “Overheating” in chapter 6.
Features of your vehicle
Shift to P (for smart key system and automatic transaxle) (cid:129) This warning message illuminates if you try to turn off the engine without the shift lever in P (Park) position. (cid:129) At this time, the Engine Start/Stop Button turns to the ACC position (If you press the Engine Start/Stop Button once more, it will turn to the ON position).
Press START button while turn steer- ing (for smart key system) (cid:129) This warning message illuminates if the steering wheel does not unlock normally when the Engine Start/Stop Button is pressed.
(cid:129) It means that you should press the Engine Start/Stop Button while turning the steering wheel right and left.
Low Key Battery (for smart key system) (cid:129) This warning message illuminates if the battery of the smart key is discharged when the Engine Start/Stop Button changes to the OFF position.
Steering wheel unlocked (for smart key system) (cid:129) This warning message illuminates if the steering wheel does not lock when the Engine Start/Stop Button changes to the OFF position.
4 73
YDM USA 4a.QXP 2016-05-03 17:27 Page 74
Features of your vehicle
Check Steering Wheel Lock System (for smart key system) (cid:129) This warning message illuminates if the steering wheel does not lock normally when the Engine Start/Stop Button changes to the OFF position.
Press brake pedal to start engine (for smart key system and automatic transaxle) (cid:129) This warning message illuminates if the Engine Start/Stop Button changes to the ACC position twice by pressing the button repeatedly without depressing the brake pedal. (cid:129) It means that you should depress the brake pedal to start the engine.
Press clutch pedal to start engine (for smart key system and manual transaxle) (cid:129) This warning message illuminates if the Engine Start/Stop Button changes to the ACC position twice by pressing the button repeatedly without depressing the clutch pedal. (cid:129) It means that you should depress the clutch pedal to start the engine.
Key not in vehicle (for smart key system) (cid:129) This warning message illuminates if the smart key is not in the vehicle when you press the Engine Start/Stop Button.
(cid:129) It means that you should always
have the smart key with you.
Key not detected (for smart key system) (cid:129) This warning message illuminates if the smart key is not detected when you press the Engine Start/Stop Button.
Press START button again (for smart key system) (cid:129) This warning message illuminates if you can not operate the Engine Start/Stop Button when there is a problem with the Engine Start/Stop Button system.
(cid:129) It means that you could start the engine by pressing the Engine Start/ Stop Button once more.
(cid:129) If the warning illuminates each time you press the Engine Start/Stop Button, we recommend that you have the vehicle inspected by an authorized Kia dealer.
74
YDM USA 4a.QXP 2016-05-03 17:27 Page 75
Press START button with smart key (for smart key system) (cid:129) This warning message illuminates if you press the Engine Start/Stop Button while the warning message “Key not detected” is illuminating. (cid:129) At this time, the immobilizer indica-
tor light blinks.
Check fuse “BRAKE SWITCH” (for smart key system and automatic transaxle/transmission) (cid:129) This warning message illuminates if the brake switch fuse is discon- nected.
(cid:129) It means that you should replace the fuse with a new one. If that is not possible, you can start the engine by pressing the Engine Start/Stop Button for 10 seconds in the ACC position.
Features of your vehicle
Shift to P or N to start engine (for smart key system and automatic transaxle) (cid:129) This warning message illuminates if you try to start the engine with the shift lever not in the P (Park) or N (Neutral) position.
Low Washer Fluid (if equipped) (cid:129) This warning message illuminates on the service reminder mode if the washer fluid level in the reser- voir is nearly empty.
(cid:129) It means that you should refill the
washer fluid.
✽✽ NOTICE You can start the engine with the shift lever in the N (Neutral) position. But, for your safety, we recommend that you start the engine with the shift lever in the P (Park) position.
Low Fuel (cid:129) This warning message illuminates
if the fuel tank is nearly empty. - When the low fuel level warning
light is illuminates.
Add fuel as soon as possible.
4 75
YDM USA 4a.QXP 2016-05-03 17:27 Page 76
Features of your vehicle
WARNING AND INDICATOR LIGHTS Warning lights
Air bag Warning Light
Seat Belt Warning Light
✽✽ NOTICE - Warning lights Make sure that all warning lights are OFF after starting the engine. If any light is still ON, this indicates a situation that needs attention.
This warning light informs the driver that the seat belt is not fastened. For more details, refer to the "Seat Belts" in chapter 3.
This warning light illuminates: (cid:129) Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It illuminates for approximately 6
seconds and then goes off.
(cid:129) When there is a malfunction with
the SRS. In this case, have your vehicle inspected by an authorized Kia dealer.
76
YDM USA 4a.QXP 2016-05-03 17:27 Page 77
Features of your vehicle
Parking Brake & Brake Fluid Warning Light
This warning light illuminates: (cid:129) Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It illuminates for approximately 3
seconds
- It remains on if the parking brake
is applied.
(cid:129) When the parking brake is applied. (cid:129) When the brake fluid level in the
reservoir is low. - If the warning light illuminates with the parking brake released, it indicates the brake fluid level in reservoir is low.
If the brake fluid level in the reservoir is low: 1.Drive carefully to the nearest safe
location and stop your vehicle.
2.With the engine stopped, check the brake fluid level immediately and add fluid as required (For more details, refer to "Brake Fluid" in chapter 7). Then check all brake components for fluid leaks. If any leak on the brake system is still found, the warning light remains on, or the brakes do not operate properly, do not drive the vehicle. In this case, have your vehicle towed to an authorized Kia dealer and inspected.
Dual-diagonal braking system Your vehicle is equipped with dual- diagonal braking systems. This means you still have braking on two wheels even if one of the dual sys- tems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the vehicle. Also, the vehicle will not stop in as short a distance with only a portion of the brake system working. If the brakes fail while you are driv- ing, shift to a lower gear for addition- al engine braking and stop the vehi- cle as soon as it is safe to do so.
4 77
YDM USA 4a.QXP 2016-05-03 17:27 Page 78
Features of your vehicle
Driving the vehicle with a warning light ON is dangerous. If the Parking Brake & Brake Fluid Warning Light illuminates with the parking brake released, it indicates that the brake fluid level is low. In this case, have your vehicle inspect- ed by an authorized Kia dealer.
78
Electronic Brake force Distribution (EBD) System Warning Light These two warning lights illuminate at the same time while driving: (cid:129) When the ABS and regular brake
system may not work normally. In this case, have your vehicle inspected by an authorized Kia dealer.
Anti-lock Brake System (ABS) Warning Light
This warning light illuminates: (cid:129) Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It illuminates for approximately 3
seconds and then goes off.
(cid:129) When there is a malfunction with the ABS (The normal braking sys- tem will still be operational without the assistance of the anti-lock brake system). In this case, have your vehicle inspected by an authorized Kia dealer.
YDM USA 4a.QXP 2016-05-03 17:27 Page 79
Features of your vehicle
WARNING - ABS/Brake
Light
When both ABS and Parking Brake & Brake Fluid Warning Lights are on, the brake system will not work normally and you may experience an unexpected and dangerous situation during sudden braking thereby increas- ing the risk of a crash or injury. In this case, avoid high speed driving and abrupt braking. Have your vehicle inspected by an authorized Kia dealer as soon as possible.
✽✽ NOTICE - Electronic Brake force Distribution (EBD) System Warning Light
When the ABS Warning Light is on or both ABS and Parking Brake & Brake Fluid Warning Lights are on, the speedometer, odometer, or trip- meter may not work. Also, the EPS
