1998 Ford Ranger Owners Manual

U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.

130

Maintenance and care

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.

Traction A B C The traction grades, from highest to lowest are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering

(turning) traction.

Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed,

underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

131

Maintenance and care

SERVICING YOUR TIRES

Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been

parked for at least one hour or has been driven less than 5 km (3 miles).

• Adjust tire pressure to recommended specifications found on the Tire

Pressure Label.

Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control.

Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the “Service Guide.” If you notice that the tires wear unevenly, have them checked. The following procedure applies to vehicles equipped with single rear wheels, if your vehicle is equipped with dual rear wheels it is recommended that only the front wheels be rotated (side to side). • Four tire rotation

132

• Five tire rotation

Maintenance and care

Replacing the tires Replace the tires when the wear band is visible through the tire treads.

When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire

pressure decal. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the decal. If you do not follow these precautions, your vehicle may not drive properly and safely.

Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.),

as originally offered by Ford.

133

Maintenance and care

Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll

over.

Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.

SNOW TIRES AND CHAINS

Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods

of time may result in damage to vehicle components.

Snow tires must be the same size and grade as the tires you currently have on your vehicle.

The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use snow tires and chains, you must install steel wheels of the same size and specifications as those originally installed. Follow these guidelines when using snow tires and chains: • Do not use tire chains on aluminum wheels. Chains may chip the • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch any • Drive cautiously. If you hear the chains rub or bang against your

wiring, brake lines or fuel lines.

wheels.

vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle.

• If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.

tire chains on dry roads.

134

Maintenance and care

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS

Important safety precautions

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.

If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly

in a collision.

The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear a hissing sound, wait until it stops before

completely removing the cap.

Automotive fuels can cause serious injury or death if misused or mishandled.

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials

and any open flames before fueling your vehicle.

• Always turn off the vehicle before • Automotive fuels can be harmful

fueling.

or fatal if swallowed. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.

• Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin, promptly remove contaminated clothing and wash skin thoroughly with soap and water.

• If fuel is splashed in the eyes, remove contact lenses (if worn), flush

with water for 15 minutes and seek medical attention.

135

Maintenance and care • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors or skin contact could cause an adverse reaction. Consult a physician immediately.

Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT. Vehicles certified to California emission standards (indicated on the underhood Vehicle Emissions Control Information label) are designed to operate on California reformulated gasolines. If California reformulated gasoline is not available when you refuel, your vehicle can be operated on non-California fuels. However, even though your engine will perform adequately on other gasolines, the performance of the emission control devices and systems may be adversely affected. Repair of damage caused by using a fuel for which your vehicle was not designed may not be covered by your warranty.

Octane recommendations Your vehicle is designed to use “Regular” unleaded with an (R+M)/2
octane rating of 87. We do not recommend gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage.

87

Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” gasoline. “Premium” gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician.

136

Maintenance and care

The American Automobile Manufacturers Association (AAMA) issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle. We recommend the use of gasolines that meet the AAMA specification if they are available. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel.

Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE. Do not use gasolines containing methanol, which can damage critical fuel system components. Damage resulting from the use of methanol may not be covered by your warranty.

Running out of fuel Avoid running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel:You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine. If you run out of fuel, your Check Engine light may come on. For more information on the Check Engine light, refer to the Instrumentation chapter.

Calculating fuel economy To accurately calculate your vehicle’s fuel economy: 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five fuel tank fill-ups, fill the fuel tank and record the current mileage reading. 4. Use one of the following equations to calculate fuel economy. Liters used x 100 4 Total kilometers traveled Total miles traveled 4 Total gallons used Keep a record for at least one month. This will provide an accurate estimate of the vehicle’s fuel economy.

137

Maintenance and care

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuel. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at • Have the services listed in your “Service Guide” performed according

high speeds.

to the specified schedule.

The Scheduled Maintenance Services listed in the “Service Guide” are required because they are considered essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine

compartment and exhaust system, which can start a fire.

Watch for fluid leaks, strange odors, smoke, loss of oil pressure, the charging system warning light, the “Check Engine” light or the temperature warning light. These events could indicate that the emission control system is not working properly.

If you smell exhaust fumes of any kind inside your vehicle, have the dealer inspect and fix your vehicle immediately. Do not drive

if you smell exhaust fumes. These fumes are harmful and could kill you.

138

Maintenance and care

Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your “Warranty Guide” for complete emission warranty information.

Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostic (OBD-II) system. If your “check engine/service engine soon” light is on, reference the applicable light description in the Warning Lights and Chimes section of your owners guide. Your vehicle may not pass the I/M test with the “check engine/service engine soon” light on. If the vehicle’s powertrain system or its battery has just been serviced, the OBD-II system is reset to a “not ready for I/M test” condition. To ready the OBD-II system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop and go, city type traffic with

at least four idle periods.

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete.

EXTERIOR BULBS

Replacing exterior bulbs Check the operation of the following lamps frequently: • headlamps • foglamps • high-mount brakelamp • brakelamps

139

Maintenance and care • turn signals • license plate lamp • tail lamps • back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance.

Replacing headlamp bulbs

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. If you are replacing the driver side headlamp, unclip the electronic module on the right side of the battery and move it out of the way. 2. Locate the headlamp bulb through the hole in the upper radiator support assembly. 3. Disconnect the electrical connector from the bulb by pulling the connector rearward.

4. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) about an eighth of a turn to free it from the bulb socket, and by sliding the ring off the plastic base. Keep the ring because it will be used again to retain the new bulb.

140

Maintenance and care

5. Remove the old bulb from its socket by gently pulling it straight back out of the socket. Do not turn the bulb while removing it. To install the new bulb: 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the socket. You may need to turn the bulb left or right to line up the grooves in the plastic base with the tabs in the socket. When the grooves are aligned, push the bulb into the socket until the plastic base contacts the rear of the socket. 2. Slip the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating it clockwise until you feel a “stop.” 3. Push the electrical connector into the rear of the plastic base until it snaps, locking it into position. 4. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again.

REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp Using the right bulbs

Function

Park/turn/side marker lamps (front) Headlamps Foglamps (if equipped) Hi-mount brakelamp Rear stop/tail lamps Rear turn lamps Rear license plate lamps

Number of

bulbs

Trade number

3157
9007
H3
906
3157
3156
194

141

Maintenance and care

Function

Backup lamp Dome lamp Map/dome-SuperCab (if equipped) Map/dome-Regular Cab (if equipped)

Number of

bulbs

Trade number

3156
912
906
212-2
906

To replace all instrument panel lights - see your dealer.

AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: 1. Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. 2. The headlamps do not seem to provide enough light for clear night vision. 3. The headlamp beams are pointed substantially away from a slightly down and to the right position.

CLEANING AND CARING FOR YOUR VEHICLE Refer to the “Customer Assistance Guide” for a list of Ford-approved cleaners, polishes and waxes.

Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight.

142

Maintenance and care

During winter months, it is especially important to wash the vehicle on a regular basis. Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle. Remove any exterior accessories, such as antennas, before entering a car wash. After washing, apply the brakes several times to dry them.

Waxing your vehicle Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle. Use tar remover to remove any tar spots.

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately.

Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar.

Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine block or • Cover the highlighted areas to prevent water damage when cleaning

other engine components.

the engine.

143

Maintenance and care

• 4.0L

• 3.0L

144

Maintenance and care

• 2.5L • Never wash or rinse the engine while it is running; water in the

running engine may cause internal damage.

Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.

Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.

Cleaning the wiper blades If the wiper blades do not wipe properly, clean the wiper blades with undiluted windshield wiper solution. Clean the windshield with undiluted windshield wiper solution or a mild non-abrasive detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.

145

Maintenance and care

Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.

Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Follow the directions that come with the cleaner.

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter.

Underbody Flush the complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage.

Inside windows Use glass cleaner for the inside windows if they become fogged.

Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water. Be careful when removing ice from outside mirrors because you may damage the reflective surface.

146

Capacities and specifications

MOTORCRAFT PART NUMBERS

FA-1616
FG-872
BXT-58
FL-1A EV-225
AGSF-22PP***

FA-1616
FG-872
BXT-58
FL-400S EV-130
AWSF-32PP***

2.5L I4 engine 3.0L V6 engine 4.0L V6 engine FA-1616
FG-872
BXT-58
FL-400S EV-147
AWSF-32F**

Component Air filter Fuel filter Battery Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. ** Two spark plugs per cylinder required (eight total) *** If any spark plug needs to be removed for inspection, it must be re-installed in the same cylinder. Cylinders No.1, 2 and 3 have a “PG” suffix. Cylinders No. 4, 5 and 6 have a “P” suffix. If any spark plug needs to be replaced, use only spark plugs with the service part number suffix letters “PP” as shown on the engine decal.

147

Capacities and specifications

REFILL CAPACITIES

Fluid

Engine oil (includes filter change) Brake fluid

Power steering fluid Transmission fluid

Engine coolant

Ford Part Name Motorcraft 5W30 Super Premium Motor Oil High Performance DOT 3 Motor Vehicle Brake Fluid Motorcraft MERCONt ATF

Motorcraft MERCONt ATF Motorcraft MERCONtV ATF

Ford Extended Life Engine Coolant (DEX-COOL)

Application

Capacity

2.5L I4 and 3.0L V6 engine

4.3L (4.5 quarts)

4.0L V6 engine

4.7L (5.0 quarts)

All

All

5-speed manual

4x2 vehicles with automatic 4x4 vehicles with automatic 2.5L I4 engine without A/C 2.5L I4 engine with A/C 3.0L V6 engine without A/C 3.0L V6 engine with A/C 4.0L V6 engine without A/C 4.0L V6 engine with A/C

Fill to line on reservoir

Fill to range on dipstick

2.65L (2.8 quarts)

9.0L (9.5 quarts)

9.3L (9.8 quarts)

6.2L (6.5 quarts)

6.8L (7.2 quarts)

9.0L (9.5 quarts)

9.6L (10.2 quarts)

7.4L (7.8 quarts)

8.1L (8.6 quarts)

148

Capacities and specifications

Fluid

Fuel tank

Ford Part Name N/A

Transfer Case Fluid Front axle fluid

Warner 13–54

Motorcraft SAE 80W90 Axle Lubricant

Rear axle fluid1

Windshield washer fluid

Motorcraft SAE 80W90 Rear Axle Lubricant Ultra-Clear Windshield Washer Concentrate

Application

Regular cab (Short wheel base) Regular cab (Long wheel base) SuperCab 4x4 Vehicles

4x4 vehicles with 2.5L I4 or 3.0L V6 engine 4x4 vehicles with 4.0L V6 engine All

All

Capacity

62.8L (16.6 gallons)

75.7L (20.0 gallons)

74.2L (19.6 gallons)

1.2L (1.25 quarts)

1.4L (1.5 quarts)

1.7L (1.8 quarts)

2.4-2.6L (2.5-2.65 quarts)

Fill to line on reservoir

1 Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Service refill capacities are determined by filling the rear axle 6 mm to 14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole.

149

Capacities and specifications

LUBRICANT SPECIFICATIONS

Ford part name or equivalent 75W90 Gear Lube Motorcraft SAE 80W90
Rear Axle Lube1
High Performance DOT 3 Motor Vehicle Brake Fluid Ford Extended Life Engine Coolant (DEX-COOL) Motorcraft 5W30 Super Premium Motor Oil

Multi-Purpose Grease

Premium Long-Life Grease

Ford part number

XY- 75W90-QL F1TZ- 19580-B

Ford specification

WSP- M2C201-A WSL- M2C192-A

C6AZ- 19542- AB

ESA- M6C25-A and DOT 3

F6AZ- 19544-AA or

ESE- M97B44-A or WSS- M97B44-D

XO-5W30-BSP or QSP

DOAZ- 19584-AA or F5AZ- 19g209-AA XG-1-C

WSS- M2C153-G and API Certification Mark ESB- M1C93-B or ESB- M1C159-A ESA- M1C75-B

Item

Front axle

Rear axle

Brake fluid and clutch fluid (if equipped)

Engine coolant

Engine oil

Hinges, latches, stricker plates, fuel filler door hinge and seat tracks

Transmission /steering/parking brake linkages and pivots, brake and clutch pedal shaft, clutch pilot bearing and. input shaft spline (manual transmission).

150

Item

Power steering fluid, transfer case fluid and transmission fluid (manual)

Automatic transmission (4R44E and 5R55E)

Windshield washer fluid

Capacities and specifications

Ford part name or equivalent Motorcraft MERCONt ATF

Motorcraft MERCONtV ATF Ultra-clear windshield washer concentrate

Ford part number

Ford specification

XT-2-QDX

MERCONt

XT-5-QM

MERCONtV

C9AZ- 19550-AB

ESR- M17P5-A

1 Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok axles.

ENGINE DATA

Engine Cubic inches Horsepower Torque

Required fuel grade Firing order Spark plug gap Ignition system Compression ratio

3.0L V6 engine 182

2.5L I4 engine 153
119 @ 5000 rpm 150 @ 5000 rpm 160 @ 4200 rpm 146 lbs. ft. @ 3000 rpm 87 octane

185 lbs. ft. @ 3250 rpm 87 octane

225 lbs. ft. @ 2750 rpm 87 octane

4.0L V6 engine 245

1-3-4-2
1.07-1.17 mm (0.042-.046 inch) EDIS

1-4-2-5-3-6
1.07-1.17 mm (0.042-.046 inch) EDIS

1-4-2-5-3-6
1.3-1.4 mm (0.052-.056 inch) EDIS

9.4:1

9.14:1

9.0:1

151

Capacities and specifications

VEHICLE DIMENSIONS

Vehicle dimensions

(1) Overall length (2) Overall width (3) Overall height 4x2/4x4
(4) Wheelbase (5) Track - Front (5) Track - Rear

Regular Cab Short Wheel Base (SWB) mm (in) 4 763 (187.5) 1 785 (70.3) 1 575 (62.0) / 1 655 (65.2) 2 831 (111.4) 1 486 (58.5) 1 455 (57.3)

Regular Cab Long Wheel Base (LWB) mm (in) 5 093 (200.5) 1 785 (70.3) 1 586 (62.4) / 1 655 (65.2) 2 983 (117.4) 1 486 (58.5) 1 455 (57.3)

Supercab mm (in)

5 153 (202.9) 1 785 (70.3) 1 585 (62.4) / 1 684 (66.3) 3 192 (125.7) 1 485 (58.5) 1 455 (57.3)

152

Capacities and specifications

153

Capacities and specifications

IDENTIFYING YOUR VEHICLE

Safety compliance label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver’s side.

MFD. BY FORD MOTOR CO. IN U.S.A.

DATE: XXXXX FGAWR: XXXXXX/XXXXXXX

GVWR:XXXXX LB/ XXXXX KG RGAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.

VIN: XXXXXXXXXXXXXXXXX

TYPE: XXXXXXXXXXXXXXX

MAXIMUM LOAD=OCCUPANTS + LUGGAGE=XXXKG/XXXXLB OCCUPANTS: X TOTAL X FR X 2ND X RR OCCUPANTS LUGGAGE XX XXXKG/XXXXLB X XXXKG/XXXXLB

TIRE: XXXX/XXXXX XXX PRESSURE (FR) XXX kPa/33 PSI COLD PRESSURE (RR) XXX kPa/33 PSI COLD TRAILER TOWING - SEE OWNER GUIDE

EXT PNT: XXXXXX XXXXXX RC: XX DSO: XXXX F0000
BAR INT TR TP/PS R AXLE TR SPR T0000
X XX XXX X XX X XXXX

UTC (cid:209) FOHT-15294A10-GA

Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.

AIR

BAG

XXXXXXXXXXXXXXXXX

Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).

154

Reporting safety defects

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C. area) or write to: NHTSA U.S. Department of Transportation 400 Seventh Street Washington D.C. 20590
You can also obtain other information about motor vehicle safety from the Hotline.

155

Index

Aiming headlamps ....................142
Air bag supplemental restraint system ..........................................47
and child safety seats ..............48
description ................................47
disposal ......................................50
indicator light ...........................50
passenger air bag ...........48,51,52

Air conditioning

manual heating and air conditioning system .......19,20,21
Ambulance packages ....................3
Anti-lock brake system (ABS)

description ................................66
Anti-theft system ........................35
Battery .......................................128
voltage gauge ............................15

Brake fluid

checking and adding ..............118
Brakes ..........................................64
anti-lock ................................64,65
anti-lock brake system (ABS) warning light .............................66
fluid, checking and adding ....118
Brake-shift interlock ...................67
Break-in period .............................2
Bulbs, replacing ........................139
headlamps ...............................140
specifications ..........................141
Changing a tire .........................101
Child safety seats ........................54
Chime

headlamps on ............................11
Cleaning your vehicle ...............142
engine compartment ..............143
fabric ........................................146
instrument panel ....................146
plastic parts ............................145
safety belts ..............................146
tail lamps .................................145
washing ....................................142
waxing .....................................143

156

wheels ......................................143
windows ..................................146

Clutch

fluid ..........................................119
Controls ..................................23,31
Driving under special conditions ....................................77
high water .................................78
slippery roads ......................78,79
Emission control system ..........138
Engine ........................................151
service points ............112,113,114
Engine block heater ...................62
Engine coolant

checking and adding ..............121
disposal ....................................122
refill capacities ........................123
Engine oil ...........................115,117
changing oil and oil filter .......118
checking and adding .......115,117
Exhaust fumes ............................63
Foglamps .....................................16
Four-Wheel Drive vehicles .........74
control trac ..........................22,75
indicator light ...........................75

Fuel

calculating fuel economy .......137
improving fuel economy ..........92
octane rating ...........................136
quality ......................................136
running out of fuel .................137
safety information relating to automotive fuels ................135
Fuel gauge ...................................12
Fuel pump shut-off switch .........93
Fuse panels

instrument panel ......................95
power distribution box .............98
Fuses .......................................94,95
Gauges, Mechanical

engine coolant temperature gauge .........................................13

Hazard flashers ...........................93
Headlamps ...................................16
daytime running lights .............16
flashing ......................................17
high beam .................................16
Heating ........................................17
High beams

indicator light .............................9
Hood ..........................................111
Instrument panel

lighting up panel and interior .17
Jump-starting your vehicle .....106, 107
attaching cables ......................107
disconnecting cables ..............108

key in ignition chime ...............11

Keys

Lamps

interior lamps .........................141

Lights, warning and indicator

air bag ..........................................8
anti-lock brakes (ABS) ..............8
anti-theft .....................................9
brake ............................................8
charging system ..........................9
check engine ............................6,7
cruise indicator .........................10
door ajar ....................................10
fuel reset .....................................8
overdrive off ................................9
safety belt ...................................8
turn signal indicator ...................9

Load limits

trailer towing ............................81
Lubricant specifications ...........150
Manual transmission

driving .............................72,73,74

Mirrors

cleaning ...................................146
side view mirrors (power) .......31
Motorcraft parts ........................147
Odometer .....................................14

Index

Off road driving, 4-wheel drive .77
Overdrive .....................................28
Panic alarm feature, remote entry system ................................33
Parking brake ..............................66
Power door locks ........................31
Power steering

fluid, checking and adding ....123
Radio ............................................24
Recreational towing, all wheels on the ground .............................89
Refill capacities for fluids ........148
Relays ..........................................94
Remote entry system .................32
illuminated entry ......................34
locking/unlocking doors ...........32
replacement/additional transmitters ...............................34
replacing the batteries .............33
Reporting safety defects ..........155
Safety restraints

extension assembly ..................45
lap and shoulder belts ...40,41,42
maintenance ..............................46
proper use .................................39
warning light and chime .........11, 45,46

Safety seats for children

attaching with tether straps ....57
tether anchorage hardware .....58
Seats ............................................37
adjusting the seat, manual .......37
jump seats ............................38,39
lumbar support .........................38
rear seat access ........................38
Servicing your vehicle ..............110
precautions when servicing ...110
Snowplowing .................................2
Special notice

diesel-powered vehicles .............3
utility-type vehicles ....................2
Speed control ..............................24

157

Index

canceling a set speed ...............27
indicator light ...........................28
resuming a set speed ...............28
tap up/tap down .......................26
turning off .................................25
Speedometer ...............................14
Starting your vehicle .............59,61
Tachometer

mechanical cluster ...................13
Tilt steering wheel ......................29
Tires ....................................130,132
changing ..................................103
checking the pressure ............132
replacing ..................................133
rotating ....................................132
snow tires and chains ............134
treadwear ................................131
Traction-lok rear axle ..........79,127
Trailer towing ..............................81
tips .............................................89

Transaxle

fluid, checking and adding (manual) .................................126

Transfer case

fluid checking .........................127

Transmission .............................124

automatic operation ..........67,68,69,70,71,72
fluid, checking and adding (automatic) .............................124
Trip odometer .............................14
Turn signal

lever ...........................................24
Vehicle dimensions ...................152
Vehicle Identification Number (VIN) ..........................................154
Vehicle loading ............................79
Ventilating your vehicle .............63
Windows

power windows, operating .......30

Windshield washer fluid and wipers

checking and adding fluid .....120
checking and replacing wiper blades ......................................129
operation ...................................29
Wrecker towing .........................109

158

Recommended fuel Fuel tank capacity (Regular cab-Short wheel base) Fuel tank capacity (Regular cab-Long wheel base) Fuel tank capacity (SuperCab) Engine oil capacity (with filter change)- 2.5L and 3.0L engines Engine oil capacity (with filter change)- 4.0L engine Tire size and pressure

Hood release

Filling station information

Unleaded fuel only - 87 octane 62.8L (16.6 gallons)

75.7 (20.0 gallons)

74.2L (19.6 gallons) 4.3L (4.5 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G See Safety Compliance Certification Label on inside of driver door. Pull handle under the left side of the instrument panel 6.2L (6.5 quarts)

9.0L (9.5 quarts)

6.8L (7.2 quarts)

9.6L (10.2 quarts)

Coolant capacity-2.5L without air conditioning Coolant capacity-2.5L with air conditioning Coolant capacity-3.0L without air conditioning Coolant capacity-3.0L with air conditioning Coolant capacity-4.0L without air conditioning Coolant capacity-4.0L with air conditioning Power steering fluid capacity Manual transmission fluid capacity 2.65L (2.8 quarts) Automatic transmission fluid 9.0L (9.5 quarts) capacity-4x2 vehicles Automatic transmission fluid capacity-4x4 vehicles

9.3L (9.8 quarts)

7.4L (7.8 quarts)

8.1L (8.6 quarts)

Fill to range on dipstick

159

Filling station information

Ensure correct automatic transmission fluid is used for a specific application. Check the container to verify the fluid is MERCONt and/or MERCON Vt approved. Some fluids have been approved as meeting both MERCONt and MERCONt V requirements and will be labeled as such. Fluids labeled as meeting only MERCONt or only MERCONt V requirements must not be used interchangeably. DO NOT mix MERCONt and MERCONt V. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. Refer to your “Service Guide” to determine the correct service interval.

160