engine switch is turned to the “LOCK” position. With the engine switch in the “ON” position, the electric cooling fan may automatically start to run if the air conditioning is on and/or the coolant tem- perature is high. Be sure the engine switch is in the “LOCK” position and that the electric cooling fan is completely stopped when working near the electric cooling fan or radiator grille.
Brake fluid
n Checking fluid level
The brake fluid level should be between the “MAX” and “MIN” lines on the tank.
“MAX” “MIN”
446
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 447 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Adding fluid Make sure to check the fluid type and prepare the necessary items.
Fluid type
Items
FMVSS No.116 DOT 3 or SAE J1703 brake fluid Clean funnel
n Brake fluid can absorb moisture from the air
Excess moisture in the fluid can cause a dangerous loss of braking effi- ciency. Use only newly opened brake fluid.
CAUTION
n When filling the reservoir
Take care because brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.
NOTICE
n If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious problem.
447
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 448 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Power steering fluid
n Fluid level The fluid level should be within the appropriate range.
Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot)
Hot: Vehicle has been driven around 50 mph (80 km/h) for 20
minutes, or slightly longer in cold temperatures. (Fluid tem-
perature, 140°F - 175°F [60°C - 80°C])
Cold: Engine has not been run for about 5 hours. (Room tempera-
ture, 50°F - 85°F [10°C - 30°C])
n Checking the fluid level Make sure to check the fluid type and prepare the necessary items.
Fluid type
Items
Automatic transmission fluid DEXRON® II or III • Rag or paper towel • Funnel (used only for adding power steering fluid)
STEP 1
STEP 2
STEP 3
STEP 4
Clean all dirt off the reservoir. Remove the reservoir cap by turning it counterclockwise and wipe the dipstick clean. Reinstall the reservoir cap. Remove the reservoir cap again and look at the fluid level.
448
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 449 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
CAUTION
n Checking the fluid level
Take care, as the reservoir may be hot.
NOTICE
n When adding fluid
Avoid overfilling, or the power steering may be damaged.
n After replacing the reservoir cap
Check the steering box case, vane pump and hose connections for leaks or damage.
449
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 450 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Battery
n Battery exterior
Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.
Terminals Ground cable Hold-down clamp
n Checking battery condition
Check the battery condition using the indicator color. Type A
Green: Good condition Dark: Charging is necessary. Have the vehicle inspected by your Toyota dealer. light yellow: Not Clear or working properly. Have the battery checked by your Toyota dealer.
Blue: Good condition White: Charging is necessary. Have the vehicle inspected by your Toyota dealer. Red: Not working properly. Have the battery checked by your Toyota dealer.
Type B
450
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 451 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Before recharging
When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging:
If recharging with the battery installed on the vehicle, be sure to discon- nect the ground cable.
l Make sure the power switch on the charger is off when connecting and
disconnecting the charger cables to the battery.
451
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 452 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
CAUTION
n Chemicals in the battery
A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: l Do not cause sparks by touching the battery terminals with tools. l Do not smoke or light a match near the battery. l Avoid contact with eyes, skin and clothes. l Never inhale or swallow electrolyte. l Wear protective safety glasses when working near the battery. l Keep children away from the battery.
n Where to safely charge the battery
Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation.
n How to recharge the battery
Only perform a slow charge (5 A or less). The battery may explode if charged at a quicker rate.
n Emergency measures regarding electrolyte
If electrolyte gets in your eyes Flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility. If electrolyte gets on your skin Wash the affected area thoroughly. If you feel pain or burning, get medical attention immediately. If electrolyte gets on your clothes It can soak through clothing on to your skin. Immediately take off the cloth- ing and follow the procedure above if necessary. If you accidentally swallow electrolyte Drink a large quantity of water or milk. Follow with milk of magnesia, beaten raw egg or vegetable oil. Get emergency medical attention immedi- ately.
452
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 453 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
NOTICE
n When recharging the battery
Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.
Washer fluid
Add washer fluid in the following situations. l Any washer does not work. l The low washer fluid warning
light comes on.
CAUTION
n When refilling washer fluid
Do not refill washer fluid when the engine is hot or running, as washer fluid contains alcohol and may catch fire if spilled on the engine etc.
NOTICE
n Do not use any fluid other than washer fluid
Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces.
n Diluting washer fluid
Dilute washer fluid with water as necessary. Refer to the freezing temperatures listed on the washer fluid tank.
453
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 454 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance Tires
Replace or rotate tires in accordance with maintenance sched- ules and treadwear. n Checking tires
location of
New tread Treadwear indicator Worn tread The treadwear indicators is shown by the “TWI” or “ ” marks, etc., molded on the sidewall of each tire. Vehicles with compact spare tire: check spare tire condi- tion and inflation pressure.
Rotate the tires in the order shown.
To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is carried out at the same inter- val as tire inspection.
n Tire rotation
Front
n The tire pressure warning system
Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 507) Vehicles with compact spare tire: The compact spare tire is not equipped with the tire pressure warning valve and transmitters.
454
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 455 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Installing tire pressure warning valves and transmitters
When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed. When new tire pressure warning valves and transmitters are installed, new tire pressure warning valve and transmitter ID codes must be registered in the tire pressure warning computer and tire pressure warning system must be initialized. Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer. (→P. 456)
Initializing the tire pressure warning system
n The tire pressure warning system must be initialized when the
tire size is changed
When the tire pressure warning system is initialized, the current tire
inflation pressure is set as the pressure benchmark.
n How to initialize the tire pressure warning system
STEP 1
Park the vehicle in a safe place and turn the engine switch to the “ACC” or “LOCK” position. While the vehicle is moving, initialization is not performed. Adjust the tire inflation pressure to the specified cold tire infla- tion pressure level. (→P. 548) Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level. Turn the engine switch to the “ON” position.
STEP 2
STEP 3
455
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 456 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
STEP 4
Push and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times.
STEP 5
Wait for several minutes with the engine switch in the “ON” position, and then turn the engine switch to the “ACC” or “LOCK” position.
Registering ID codes
The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.
456
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 457 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n When to replace your vehicle's tires
Tires should be replaced if: l You have tire damage such as cuts, splits, cracks deep enough to
expose the fabric or bulges indicating internal damage
l A tire goes flat repeatedly or cannot be properly repaired due to the
size or location of a cut or other damage
If you are not sure, consult with your Toyota dealer.
n Replacing tires and wheels
If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light comes on after blinking for 1 minute to indicate a system malfunction.
n Tire life
Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.
n If the tread wears down below 0.16 in. (4 mm) on snow tires
The effectiveness of snow tires is lost.
n Maximum load of tire
Check that the maximum load of the replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. As for the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire, and as for the Gross Axle Weight Ratings (GAWR), see the Certification Label. (→P. 543, 553).
457
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 458 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Tire types
1 Summer tires
Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.
2 All season tires
All season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions, as well as for use year round. All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving.
3 Snow tires
For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, con- struction and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restriction. Snow tires should be installed on all wheels. (→P. 226) n Initializing the tire pressure warning system
Initialize the tire pressure warning system with the tire inflation pressure adjusted to the specified level.
n If you push the tire pressure warning reset switch accidentally
If initialization is performed, adjust the tire inflation pressure to the speci- fied level and initialize the tire pressure warning system again.
458
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 459 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n When the initialization of the tire pressure warning system has
failed Initialization can be completed in several minutes. However, in the fol- lowing cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. l When operating the tire pressure warning reset switch, the tire pres-
sure warning light does not flash 3 times.
l After carrying out the initialization procedure, the tire pressure warn-
ing light blinks for 1 minute then stays on after driving for about 20
minutes.
n Routine tire inflation pressure checks
The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.
459
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 460 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Tire pressure warning system certification
MODEL/FCC IDs: Transmitter: GQ4-32T Receiver: GQ4-37R IC (Canada) IDs: Transmitter: 1470A-13T Receiver: 1470A-9R
For vehicles sold in the U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user's authority to operate the equip- ment.
For vehicles sold in Canada
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
460
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 461 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
CAUTION
n When inspecting or replacing tires
Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train, as well as dangerous han- dling characteristics, which may lead to fatal or injury accidents. l Do not mix tires of different makes, models, tread patterns or tread-
wear.
l Do not use tire sizes other than those recommended by Toyota. l Do not mix radial, bias-belted, or bias-ply tires. l Do not mix summer, all season and snow tires. l Do not tow if your vehicle has a compact spare tire installed.
n When initializing the tire pressure warning system
Do not push the tire pressure warning reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pres- sure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.
461
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 462 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
NOTICE
n Repairing or replacing tires, wheels and tire pressure warning
valves and transmitters When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. n To avoid damaging the tire pressure warning valves and transmit-
ters Do not use liquid sealants on flat tires.
n Do not use puncture sealant sprays to repair flats
Puncture sealant sprays may damage tire pressure warning valves and transmitters.
n Driving on rough roads
Take particular care when driving on roads with loose surfaces or pot- holes. These conditions may cause losses in tire inflation pressure, reducing the cushioning ability of the tires. In addition driving on rough roads may cause damage to the tires themselves, as well as the vehicle's wheels and body.
n If tire inflation pressures become low while driving
Do not continue driving, or your tires and/or wheels may be ruined.
462
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 463 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance Tire inflation pressure
n Tire inflation pressure
The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 548)
463
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 464 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Inspection and adjustment procedure
Tire valve Tire pressure gauge
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust the pressure. If you add too much air, press the center of the valve to lower. After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage. Reinstall the tire valve cap.
n Tire inflation pressure check interval
You should check tire inflation pressure every two weeks, or at least once a month. Do not forget to check the spare.
464
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 465 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Effects of incorrect tire inflation pressure
Driving with incorrect tire inflation pressure may result in the following: l Reduced fuel efficiency l Reduced driving comfort and tire life l Reduced safety l Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer.
n Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following: l Check only when the tires are cold.
If your vehicle has been parked for at least 3 hours and has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
l Always use a tire pressure gauge.
The appearance of the tire can be misleading. In addition, tire infla- tion pressures that are even just a few pounds off can degrade ride and handling.
l Do not bleed or reduce tire inflation pressure after driving. It is normal
for the tire inflation pressure to be higher after driving.
l Never exceed the vehicle capacity weight.
Passengers and luggage weight should be placed so that the vehicle is balanced.
465
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 466 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
CAUTION
n Proper inflation is critical to save tire performance
Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. l Excessive wear l Uneven wear l Poor handling l Possibility of blowouts resulting from overheated tires l Poor sealing of the tire bead l Wheel deformation and/or tire separation l A greater possibility of tire damage from road hazards
NOTICE
n When inspecting and adjusting tire inflation pressure
Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps have been lost, replace them as soon as possible.
466
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 467 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance Wheels
If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. n Wheel selection
When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and offset. Replacement wheels are available at your Toyota dealer. Toyota does not recommend using: l Wheels of different sizes or types l Used wheels l Bent wheels that have been straightened
n Aluminum wheel precautions
l Use only Toyota wheel nuts and wrenches designed for use
with your aluminum wheels.
l When rotating, repairing or changing your tires, check that the
wheel nuts are still tight after driving 1000 miles (1600 km).
l Be careful not to damage the aluminum wheels when using
tire chains.
l Use only Toyota genuine balance weights or equivalent and a
plastic or rubber hammer when balancing your wheels.
n When replacing wheels
The wheels of your Toyota are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed. (→P. 455)
467
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 468 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
CAUTION
n When replacing wheels
l Do not use wheels that are a different size from those recommended in
the Owner’s Manual, as this may result in loss of handling control.
l Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing serious injury or death.
NOTICE
n Replacing tire pressure warning valves and transmitters
l Because tire repair or replacement may affect the tire pressure warning valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
l Ensure that only genuine Toyota wheels are used on your vehicle.
Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.
468
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 469 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance Air conditioning filter
The air conditioning filter must be cleaned or changed regularly to
maintain air conditioning efficiency.
n Removal method
STEP 1
Turn the engine switch to the “LOCK” position.
STEP 2
STEP 3
Open the glove box. Slide off the damper.
Push in each side of the glove box to disconnect the claws.
STEP 4
Remove the filter case.
469
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 470 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
STEP 5
Remove the filter from the fil- ter case.
If the filter is dirty, clean by blowing air through the downward side.
compressed from
filter
the
Hold the air gun 2 in. (5 cm)
from the filter and blow for
approximately 2 minutes at 72
psi (500 kPa, 5.0 kgf/cm2 or
bar).
If it is not available, have the
filter cleaned by your Toyota
dealer.
Install a new filter to the filter case.
The “↑UP” marks shown on the filter should be pointing up.
n Cleaning method
n Replacement method
470
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 471 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Checking interval
Inspect, clean and replace the air conditioning filter according to the mainte- nance schedule. In dusty areas or areas with heavy traffic flow, more fre- quent cleaning or early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)
n If air flow from the vents decreases dramatically
The filter may be clogged. Check the filter and replace it if necessary.
NOTICE
n To prevent damage to the system
l When using the air conditioning system, make sure that a filter is always
installed.
l When cleaning the filter, do not clean the filter with water.
471
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 472 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance Wireless remote control battery
Replace the battery with a new one if it is discharged. n You will need the following:
Lithium battery (CR2032)
n Replacing the battery
STEP 1
Remove the cover using a coin protected with tape etc.
STEP 2
Remove the discharged trans- mitter battery.
Insert a new battery with the “+” terminal facing up.
472
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 473 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n If the wireless remote control battery is discharged
The following symptoms may occur. l The wireless remote control will not function properly. l The operational range is reduced.
n Use a CR2032 lithium battery
l Batteries can be purchased at your Toyota dealer, jewelers, or camera
stores.
l Replace only with the same or equivalent type recommended by your
Toyota dealer.
l Dispose of used batteries according to the local laws.
CAUTION
n Removed battery and other parts
Keep away from children. These parts are small and if swallowed by a child they can cause choking.
NOTICE
n For normal operation after replacing the battery
Observe the following precautions to prevent accidents. l Always work with dry hands.
Moisture may cause the battery to rust.
l Do not touch or move any other components inside the remote control. l Do not bend either of the battery terminals.
473
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 474 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have
blown. If this happens, check and replace the fuses as necessary.
STEP 1
Turn the engine switch to the “LOCK” position. The fuses are located in the following places. To check the fuses, follow the instructions below.
STEP 2
Engine compartment
Push the tab in and lift the lid off.
Driver’s side instrument panel
Remove the lid.
474
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 475 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Passenger’s side instrument panel
1. Open the glove box. Slide
off the damper.
2. Push in each side of the glove box to disconnect the claws.
STEP 3
After a system failure, see “Fuse layout and amperage rat- ings” (→P. 478) for details about which fuse to check.
475
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 476 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
STEP 4
Take out the pullout tool.
type A
Only fuse can be removed using the pullout tool.
STEP 5
Check if the fuse has blown.
Type A
Type B
Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.
Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.
476
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 477 Tuesday, June 10, 2008 11:01 AM
Type C
Type D
4-3. Do-it-yourself maintenance
Normal fuse Blown fuse Contact your Toyota dealer.
Normal fuse Blown fuse Contact your Toyota dealer.
477
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 478 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Fuse layout and amperage ratings
n Engine compartment
Fuse
Ampere
Circuit
1 MAIN
AM2
ETCS
DRL
DOOR NO.2
HORN
DOME
478
30 A
30 A
10 A
20 A
25 A 10 A
10 A
Headlights, daytime running light
system, H-LP RL, H-LP LL
INJ, IGN, GAUGE 2
Multiport fuel injection system/
sequential multiport fuel injection
system
Daytime running light system,
H-LP RH, H-LP LH
Power door lock system
Horns
Personal/interior lights, vanity
lights, door courtesy lights, luggage
compartment light, engine switch
light, trip information display
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 479 Tuesday, June 10, 2008 11:01 AM
Fuse
RAD NO.1
EFI NO.1
10 ALT-S
11 HAZ
12 ECU-B
13 H-LP RH
14 H-LP LH
15 RAD NO.3
16 EFI NO.2
17 A/F
18 SPARE 19 SPARE 20 SPARE 21 SPARE 22 RR2 SEAT 23 HTR 24 FAN 25 PBD 26 R-PSD
4-3. Do-it-yourself maintenance
Ampere
Circuit
15 A
20 A
7.5 A
15 A
10 A
15 A 15 A 30 A
10 A
25 A
15 A 20 A 30 A 30 A 50 A 50 A 50 A 30 A 30 A
Audio system
Multiport fuel injection system/
sequential multiport fuel injection
system, EFI NO.2
Charging system
Turn signal lights, emergency
flashers
Power sliding door, air conditioning
system, power windows, multiplex
communication system, meter and
gauge, wireless remote control sys-
tem
Right-hand headlight
Left-hand headlight
Audio system
Multiport fuel injection system/
sequential multiport fuel injection
system
Multiport fuel injection system/
sequential multiport fuel injection
system
Spare fuse
Spare fuse
Spare fuse
Spare fuse
Power third seat
Air conditioning system, A/C
Electric cooling fans
Power back door
Right side power sliding door
479
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 480 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Fuse
Ampere
Circuit
27
L-PSD
28 RR A/C
29 DEF
30 SPARE
31 ALT
32 ABS1
33 ABS2
34 ST
35
L-RR2 SEAT
36 R-RR2 SEAT
37 H-LP RL
38 H-LP LL
39 RSE
40
INJ
30 A 40 A 40 A 7.5 A
140 A
50 A
30 A
30 A 30 A 30 A 10 A
10 A
7.5 A
10 A
Left side power sliding door Rear air conditioning system Rear window defogger, MIR HTR Spare fuse Charging system, RR A/C, HTR, FAN, PBD, R-PSD, L-PSD, DEF Anti-lock brake system, traction control system, vehicle stability control system Anti-lock brake system, traction control system, vehicle stability control system Starting system Power third seat Power third seat Right-hand headlight (low beam) Left-hand headlight (low beam), front fog lights Rear seat entertainment system Multiport fuel injection system/ sequential multiport fuel injection system
480
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 481 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Under the driver’s side instrument panel
Fuse 1 MIR HTR
RAD2
PWR OUTLET CIG
ECU ACC
6 GAUGE2
IGN
IG2
RR WIP
10 WIP
11 GAUGE1
12 S-HTR
Ampere
Circuit
10 A
7.5 A
15 A 15 A
7.5 A
7.5 A
7.5 A
7.5 A
15 A
30 A
10 A
15 A
Outside rear view mirror defoggers Audio system, navigation system, rear seat entertainment system Power outlets Cigarette lighter Shift lock control system, air condi- tioning system, power rear view mirror control Meter and gauge Multiport fuel injection system/ sequential multiport fuel injection system, SRS airbag system, multi- plex communication system Multiport fuel injection system/ sequential multiport fuel injection system Rear window wiper Windshield wiper and rear window wiper Back-up lights, turn signal lights, emergency flashers Seat heaters
481
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 482 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Fuse
Ampere
Circuit
13 WSH
14 HTR
20 A
10 A
15 ECU-IG
10 A
16 PANEL
10 A
17 TAIL
18 S/ROOF 19 AC INV 20 FR DEF
21 AM1
10 A
25 A 15 A 15 A
7.5 A
Windshield washer and rear win- dow washer Air conditioning system Intuitive parking assist system, rear view monitor system, multiplex communication system, multiport fuel injection system/sequential multiport fuel injection system, anti- lock brake system, traction control system, vehicle stability control system, shift lock control system, dynamic laser cruise control sys- tem, seat heaters, power back door, moon roof, multi-information display, auto anti-glare inside rear view mirror, power windows, power outlets (115 V), power third seat, driving position memory system Air conditioning system, seat heat- ers, audio system, navigation sys- tem, power sliding door, power back door, trip information display, rear window defogger, emergency flashers, instrument panel lights, steering switch lights Stop/tail lights, license plate lights, parking lights, side maker lights Moon roof Power outlets (115 V) Windshield wiper de-icer Multiport fuel injection system/ sequential multiport fuel injection system, starter system
482
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 483 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
Fuse
Ampere
Circuit
22 STOP
10 A
23 P/W
24 OBD 25 FOG 26 P/VENT 27 P/SEAT 28 PWR
25 A
7.5 A 15 A 15 A 30 A 30 A
Stop/tail lights, high mounted stop- light, shift lock control system, anti- lock brake system, traction control system, vehicle stability control system, multiport fuel injection sys- tem/sequential multiport fuel injec- tion system, multiplex communication system Power windows, power rear view mirror On-board diagnosis system Front fog lights Power quarter windows Power front seats Power windows
483
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 484 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Under the passenger’s side instrument panel
Fuse
Ampere
Circuit
ST
A/C SFT
7.5 A
7.5 A 5 A
Multiport fuel injection system/ sequential multiport fuel injection system Manual air conditioning system Shift lock control system
n After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (→P. 486) If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer.
n If there is an overload in the circuits
The fuses are designed to blow before the entire wiring harness is damaged.
484
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 485 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
CAUTION
n To prevent system breakdowns and vehicle fire
Observe the following precautions. Failing to do so may cause damage, and possibly a fire or injury. l Never use a fuse of a higher amperage rating than indicated, or use any
other object in place of a fuse.
l Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.
l Do not modify fuses or the fuse box.
NOTICE
n Before replacing fuses
Have the cause of electrical overload determined and repaired by your Toyota dealer as soon as possible.
485
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 486 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance Light bulbs
You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. n Preparing a replacement light bulb
Check the wattage of the light bulb being replaced. (→P. 549)
n Turning the power back door main switch off
→P. 48
n Front bulb locations
Headlight low beams (halogen bulbs)
Front side marker lights
Parking and front turn signal lights
Headlight high beams
486
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 487 Tuesday, June 10, 2008 11:01 AM
n Rear bulb locations
4-3. Do-it-yourself maintenance
Rear turn signal lights
Back-up lights
Stop/tail and rear side marker lights
License plate lights
Tail lights
Replacing light bulbs
n Headlight (halogen bulbs)
STEP 1
Turn the bulb base counterclock- wise.
Headlight (high beam) Headlight (low beam)
STEP 2
Pull out the light bulb while depressing the lock release.
487
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 488 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Front side marker light
STEP 1
Turn the bulb base counterclock- wise.
STEP 2
Remove the light bulb.
488
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 489 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Parking and front turn signal lights
STEP 1
Turn the bulb base counterclock- wise.
STEP 2
Remove the light bulb.
489
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 490 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Rear turn signal, stop/tail and rear side marker lights
STEP 1
Remove the securing bolts and remove the unit.
To protect the cover, place a rag between the flathead screwdriver and cover as shown in the illus- tration.
Turn the bulb bases counter- clockwise.
Remove the light bulbs. Rear turn signal light Stop/tail and rear side marker light
STEP 2
STEP 3
490
SIENNA_U_(L/O_0807)
SIENNA_U_45452U.book Page 491 Tuesday, June 10, 2008 11:01 AM
4-3. Do-it-yourself maintenance
n Tail and back-up lights
STEP 1
Open the back door and remove the strap.
STEP 2
STEP 3
Remove board.
the back door
trim
Turn the bulb bases counter- clockwise.
STEP 4
Remove the light bulbs.