2006 Toyota Sienna Owners Manual

button, or the seat could strike the rear passenger or hit your body against the steering wheel. If this happens, you can stop the move- ment by pressing another driving position memory switch, or de- pressing the brake pedal.

the seat

(cid:1) When returning seats to their origi- nal position, observe the following precautions in order to prevent per- sonal injury in a collision or sud- den stop: Be careful not to get your hands or feet pinched in the seat. Make sure is securely locked by pushing forward and rear- ward on the top of the seatback or by trying to pull up the edge of the bottom cushion. Failure to do so will prevent the seat belt from oper- ating properly. Make sure the seat belts are not twisted or caught under the seat and are arranged in their proper position and are ready to use.

Folding the seats up will enlarge the lug- gage compartment. See “—Stowage pre- cautions” on page 399 in Section 2 for precautions when loading luggage.

65

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Adjusting second seats

1. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. 2. SEATBACK

ADJUSTING

ANGLE

LEVER/STRAP (from front)

Lean forward and pull the lever or strap toward you. Then lean back to the de- sired angle and release the lever or strap. 3. SEATBACK

ADJUSTING

ANGLE

STRAP (from rear)

Pull the strap and push the seatback forward or pull it backward to the de- sired angle and release the strap.

Outer seat

66

Center seat

2006 SIENNA from March ‘06 Prod. (OM45443U)

CAUTION

reclining

Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the passengers are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt. In the event of a frontal collision, the more the seat is reclined, the greater the risk of death or personal injury.

06 SIENNA_U (L/O 0603)

—Tumbling second seat for third seat entry

CAUTION

After returning the seat, make sure the seat is securely locked by push- ing forward and rearward on the top of the seatback or by trying to pull up the edge of the bottom cushion. Failure to do so will prevent seat belt from operating properly.

For access to the third seat, perform the following procedure. Fold down the seatback while pulling the seatback angle adjusting lever or strap and swing up the seat. After passengers are in, return the seat until it locks securely, and lift up the seat back by pulling the lever or strap.

67

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Tumbling second seats (outer seats)

the

the

from

returning

the seat

tumbled second

When seat to its original position: the Once is moved tumbled position folded- down to position, it cannot be directly returned to the tumbled position again. (It is im- possible to operate the seat in the or- der 1→2→1.) When you the folded- down seat its tumbled position (position 1), you must return the folded- down seat (position 2) to (position 3) once. (It is possible to operate the seat in the order 1→2→3→1.)

its original position

return to

(position 2)

BEFORE TUMBLING SECOND SEATS (7- passenger models only) 1. Stow the second seat belt buckles

as shown in the illustration.

This prevents out when you tumble the second seats.

the buckles

from sticking

68

NOTICE

To prevent damage to the seat belt buckles, the buckles must be stowed before you fold the seatback.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

2. Make sure the shoulder belt passes through the hanger when folding the second seat.

This prevents the shoulder belt from being damaged.

TUMBLING SECOND SEATS 1. Lower the head restraint to the low- est position. Hold the center of the lever and pull it up. Then slide the seat to the rear- most lock position.

2. 7- passenger models only: Pull the

armrests up.

CAUTION

The seat belt must be removed from the hanger when the seat belt is in use.

69

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

length of

(cid:1) When tumbling the second seats, fix the seats securely by adjusting the the holding strap. Failure to do so may cause an un- expected accident or severe injury in the event of emergency braking or a collision.

(cid:1) Do not sit on the third seats when the second seat is tumbled in order to prevent personal injury in a colli- sion or sudden stop.

4. Take the holding strap out of the pocket. Pass the strap through the assist grip, and hook it as shown in the illustration.

When returning its original position, put the holding strap into the pocket.

the second seat

to

NOTICE

(cid:1) Do not use anything other than the assist grip to hold the second seat. (cid:1) The holding strap must be stowed into the pocket when it is not in use.

2006 SIENNA from March ‘06 Prod. (OM45443U)

3. Fold down the seatback while pulling the seatback angle adjusting lever or strap and swing up the seat.

If the front seat is in the way, adjust it so it will not interfere.

CAUTION

(cid:1) Make sure the seat is free of people or luggage. Then, hold the seat and slowly move it. Otherwise, people may be injured or luggage may be damaged if the seat hits them.

(cid:1) To avoid serious injury, do not sit

on the folded seatback.

70

06 SIENNA_U (L/O 0603)

CAUTION

To avoid serious injury: (cid:1) Do not set up the seatback table

while the vehicle is moving.

(cid:1) Do not sit on the folded seatback. (cid:1) Make sure the second seat is se- curely locked in position when you set the second seat as a temporary table.

NOTICE

To prevent damage to the seat, avoid putting heavy loads on the temporary table.

71

2006 SIENNA from March ‘06 Prod. (OM45443U)

You can use the seatback as a temporary table only when the vehicle is stopped. When you fold down the seatback from its upright position, locks will disengage. In this case, lift up the seat and fold down again to engage the rear leg locks.

the rear

leg

the

the

from

returning

the seat

tumbled second

When seat to its original position: the Once is moved tumbled position folded- down to position, it cannot be directly returned to the tumbled position again. (It is im- possible to operate the seat in the or- der 1→2→1.) When you the folded- down seat its tumbled position (position 1), you must return the folded- down seat (position 2) to (position 3) once. (It is possible to operate the seat in the order 1→2→3→1.)

its original position

return to

(position 2)

06 SIENNA_U (L/O 0603)

—Tumbling second seat (center seat)

CAUTION

When folding or returning the seat, observe the following precautions in order to prevent personal injury: (cid:1) Do not fold or remove the seat

while the vehicle is moving.

(cid:1) Be careful not to get your hands or

feet pinched in the seat.

When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: (cid:1) Make sure is securely locked by pushing forward and rear- ward on the top of the seatback or by trying to pull up the edge of the bottom cushion. Failure to do so will prevent the seat belt from oper- ating properly.

the seat

(cid:1) Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use.

TUMBLING SECOND SEAT 1. Lower the head restraint to the low- est position. Hold the center of the lever and pull it up. Then slide the seat to the rear- most lock position.

72

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

(cid:1) Make sure the seat is free of people or luggage. Then, hold the seat and slowly move it. Otherwise, people may be injured or luggage may be damaged if the seat hits them.

(cid:1) To avoid serious injury, do not sit

on the folded seatback.

2. Fold down the seatback while pulling

the seatback angle adjusting strap.

3. Pull the seat lock release lever (red)

and swing up the seat.

If the front seats are in the way, adjust it so it will not interfere. If the seat is not in the rear- most lock position, the rear leg will not unlock. In this case, slide the seat to the rear- most lock position and then do the above op- eration again.

73

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

length of

(cid:1) When tumbling the second seats, fix the seats securely by adjusting the the holding strap. Failure to do so may cause an un- expected accident or severe injury in the event of emergency braking or a collision.

(cid:1) Do not sit on the third seats when the second seat is tumbled in order to prevent personal injury in a colli- sion or sudden stop.

You can use the seatback as a temporary table only when the vehicle is stopped.

CAUTION

To avoid serious injury: (cid:1) Do not set up the seatback table

while the vehicle is moving.

(cid:1) Do not sit on the folded seatback. (cid:1) Make sure the second seat is se- curely locked in position when you set the second seat as a temporary table.

2006 SIENNA from March ‘06 Prod. (OM45443U)

4. Take the holding strap out of the pocket. Pass the strap through the assist grip, and hook it as shown in the illustration.

When returning its original position, put the holding strap into the pocket.

the second seat

to

NOTICE

(cid:1) Do not use anything other than the assist grip to hold the second seat. (cid:1) The holding strap must be stowed into the pocket when it is not in use.

74

06 SIENNA_U (L/O 0603)

NOTICE

CAUTION

—Removing second seats (outer seats)

To prevent damage to the seat, avoid putting heavy loads on the temporary table.

When folding or returning the seat, observe the following precautions in order to prevent personal injury: (cid:1) Do not fold or remove the seat

while the vehicle is moving.

(cid:1) Be careful not to get your hands or

feet pinched in the seat.

When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: (cid:1) Make sure is securely locked by pushing forward and rear- ward on the top of the seatback or by trying to pull up the edge of the bottom cushion. Failure to do so will prevent the seat belt from oper- ating properly.

the seat

(cid:1) Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use.

BEFORE REMOVING SECOND SEATS (7- passenger models only) 1. Stow the second seat belt buckles

as shown in the illustration.

This prevents out when you fold up the second seats.

the buckles

from sticking

NOTICE

To prevent damage to the seat belt buckles, the buckles must be stowed before you fold the seatback.

75

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

REMOVING SECOND SEATS 1. Lower the head restraint to the low- est position. Hold the center of the lever and pull it up. Then slide the seat to the rear- most lock position.

2. 7- passenger models only: Pull the

armrests up.

2006 SIENNA from March ‘06 Prod. (OM45443U)

2. Make sure the shoulder belts pass folding

the hangers when

through the second seat.

This prevents the shoulder belt from being damaged.

CAUTION

The seat belt must be removed from the hanger when the seat belt is in use.

76

06 SIENNA_U (L/O 0603)

To prevent personal injury in a colli- sion or sudden stop: (cid:1) Do not sit on or place anything on

the folded seatback while driving.

(cid:1) Do not

the loose in the vehicle.

leave

removed seat

(cid:1) Do not try to sit on or place any-

thing on the removed seat.

NOTICE

(cid:1) Avoid putting heavy loads on the removed seat. The metallic tips of the seat leg may be damaged and the seat cannot be reinstalled.

(cid:1) Do not carry the removed seat with holding the seat position adjusting lever. Otherwise, the seat may slide and not installed properly. If you slide the removed seat, return the seat to the rear-most position be- fore it is installed.

3. Fold down the seatback while pulling the seatback angle adjusting lever or strap and swing up the seat.

4. Pull and hold the front leg release strap and fold down the seat. Then the front locks will disengage and you can remove the seat.

leg

CAUTION

(cid:1) Make sure the seat is free of people or luggage. Then, hold the seat and slowly move it. Otherwise, people may be injured or luggage may be damaged if the seat hits them.

(cid:1) To avoid serious injury, do not sit

on the folded seatback.

CAUTION

When removing the seat, observe the following to prevent personal injury: (cid:1) Do not fold or remove the seat

while the vehicle is moving.

(cid:1) Be careful not to get your hands or

feet pinched in the seat.

(cid:1) Be careful not to hit the removed seat against a person or drop it on yourself.

77

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Installing second seats (outer seats)

Front of the vehicle

Front of the vehicle

7- passenger models

8- passenger models

78

is not

When you install the second seats, be sure to place it where the seat is origi- nally positioned because each second seat interchangeable. You can distinguish the original seat position by the position of the front seat leg pin and the shape of the seat striker bezel in the floor. The right side second seat has a pin in the outside of the right front leg and the left side second seat has a pin in the outside of the left front leg as shown in the illustration.

CAUTION

You must install the seat in proper position to wear the seat belt proper- ly. Failure to be properly restrained with the seat belt in an accident can cause death or serious injury. Refer to the label on the side of the seat for additional installation instructions.

NOTICE

You must install the seat in its origi- nal position. If it is installed in the wrong position, the seat lock or bezel will be damaged.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

1. Align the front leg hooks with the rear strikers in the floor. Then swing up the seat.

2. Make sure the front

is locked securely, fold down the seat and en- gage the rear leg lock.

leg

You can easily align the front leg hooks with the rear strikers by using the floor bezel. Put the front legs of the seat short of the rear strikers as shown in the il- lustration. Then slide forward along the groove of the bezel until the front legs will reach the striker. Make sure the front legs align with the striker, swing up the seat.

the seat

79

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

NOTICE

When installing the seat, make sure to align the front leg hooks with both of the rearmost strikers in the floor. If you align the legs with the front strikers, the bezel in the floor will be damaged.

If you lock the rear legs before the front legs are locked securely, disengage the rear leg lock by pushing the red pin inside each rear leg. Then reinstall the seat fol- lowing the correct procedure.

80

2006 SIENNA from March ‘06 Prod. (OM45443U)

the

the

from

returning

the seat

tumbled second

When seat to its original position: the Once is moved tumbled position folded- down to position, it cannot be directly returned to the tumbled position again. (It is im- possible to operate the seat in the or- der 1→2→1.) When you the folded- down seat its tumbled position (position 1), you must return the folded- down seat (position 2) to (position 3) once. (It is possible to operate the seat in the order 1→2→3→1.)

its original position

return to

(position 2)

06 SIENNA_U (L/O 0603)

CAUTION

When reinstalling the seat, observe the following to prevent personal inju- ry: (cid:1) Do not reinstall the seat while the

vehicle is moving.

(cid:1) Be careful not to get your hands or

feet pinched in the seat.

(cid:1) Be careful not to hit the removed seat against a person or drop it on yourself.

the

(cid:1) After folding or installing the seat, push it forward and backward to make sure it is locked in position. When reinstalling seats to their origi- nal position, observe following precautions in order to prevent per- sonal injury in a collision or sudden stop: (cid:1) Make sure

is securely locked by pushing forward and rear- ward on the top of the seatback or by trying to pull up the edge of the bottom cushion. Failure to do so will prevent the seat belt from oper- ating properly.

the seat

(cid:1) Make sure the seat belts are not twisted or caught under the seat and are arranged in their proper position and are ready to use.

(cid:1) Install each seat in the same posi- tion from which it was removed. Failure to do so will prevent the occupants from using seat belts properly.

(cid:1) Do not reinstall the seat with its

back facing forward.

(cid:1) Make sure

the seat

is securely

locked in the proper position.

NOTICE

Do not carry the removed seat by holding the seat position adjusting le- ver. Otherwise, the seat may slide and not be installed properly. If you slide the removed seat, return the seat to the rear-most position before it is installed.

81

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Removing second seat (center seat)

7- passenger models only: The right side seat can be moved to the inside when the console box is not installed between the second seats.

REMOVING CENTER SECOND SEAT 1. Lower the head restraint to the low- est position. Hold the center of the lever and pull it up. Then slide the seat to the rear- most lock position.

82

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

(cid:1) Make sure the seat is free of people or luggage. Then, hold the seat and slowly move it. Otherwise, people may be injured or luggage may be damaged if the seat hits them.

(cid:1) To avoid serious injury, do not sit

on the folded seatback.

2. Fold down the seatback while pulling

the seatback angle adjusting strap.

3. Pull the rear leg release lever (red)

and swing up the seat.

If the seat is not in the rear- most lock position, the rear leg will not unlock. In this case, slide the seat to the rear- most lock position and then do the above op- eration again.

83

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

NOTICE

(cid:1) Avoid putting heavy loads on the removed seat. The metallic tips of the seat leg may be damaged and the seat cannot be reinstalled.

(cid:1) Do not carry the removed seat with holding the seat position adjusting lever.

When removing the seat, observe the following to prevent personal injury: (cid:1) Do not fold or remove the seat

while the vehicle is moving.

(cid:1) Be careful not to get your hands or

feet pinched in the seat.

(cid:1) Be careful not to hit the removed seat against a person or drop it on yourself.

To prevent personal injury in a colli- sion or sudden stop: (cid:1) Do not sit on or place anything on

the folded seatback while driving.

(cid:1) Do not

the loose in the vehicle.

leave

removed seat

(cid:1) Do not try to sit on or place any-

thing on the removed seat.

2006 SIENNA from March ‘06 Prod. (OM45443U)

4. Pull and hold the front leg release strap and fold down the seat. Then the front locks will disengage and you can remove the seat.

leg

84

—Installing seconds seat (center seat)

Front of the vehicle

06 SIENNA_U (L/O 0603)

is not

When you install the second seats, be sure to place it where the seat is origi- nally positioned because each second seat interchangeable. You can distinguish the original seat position by the position of the front seat leg pin and the shape of the seat striker bezel in the floor. The second center seat has a pin in the inside of the right front leg as shown in the illustration.

CAUTION

You must install the seat in proper position to wear the seat belt proper- ly. Failure to be properly restrained with the seat belt in an accident can cause death or serious injury. Refer to the label on the side of the seat for additional installation instructions.

NOTICE

You must install the seat in its origi- nal position. If it is installed in the wrong position, the seat lock or bezel will be damaged.

1. Align the front leg hooks with the rear strikers in the floor. Then swing up the seat.

85

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

You can easily align the front leg hooks with the rear strikers by using the floor bezel. Put the front legs of the seat short of the rear strikers as shown in the il- lustration. Then slide forward along the groove of the bezel until the front legs will reach the striker. Make sure the front legs align with the striker, swing up the seat.

the seat

NOTICE

When installing the seat, make sure to align the front leg hooks with the rearmost strikers of each pair in the floor. If you align the legs with the front strikers, the bezel in the floor will be damaged.

2. Make sure the front

is locked securely, fold down the seat and en- gage the rear leg lock.

leg

86

2006 SIENNA from March ‘06 Prod. (OM45443U)

If you lock the rear legs before the front legs are not lock securely, disengage the rear leg lock by pulling the rear leg re- lease lever. Then reinstall the seat follow- ing the correct procedure.

06 SIENNA_U (L/O 0603)

INSTALLING THE SECOND CENTER SEAT IN THE FRONT AND CENTER POSITION The second center seat can be used in the forward position. To use the center second seat in the for- ward position, install according to the fol- lowing procedure.

87

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

BEFORE INSTALLING THE SECOND CENTER SEAT IN FRONT AND CENTER POSITION 1. Slide the front seats forward from the

the rear- most position, stand seatbacks to the upright position.

2. For vehicles equipped with the front seat side table, pull up the lock re- lease lever and fold the table down.

INSTALLING THE SECOND CENTER SEAT IN THE FRONT AND CENTER POSITION 1. Remove the second center seat from the normal position. (For details, see “—Removing second seat (center seat)” on page 82 in this Section.) Align the front leg hook with the rear striker of the forward pair. Then swing the seat until it reaches the folded seat side table.

88

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

2. Push the foot pedal forward to se- curely latch the front leg locks. Make sure the front leg is locked securely, fold down the seat and engage the rear leg lock.

CAUTION

When reinstalling the seat, observe the following to prevent personal inju- ry: (cid:1) Do not reinstall the seat while the

vehicle is moving.

(cid:1) Be careful not to get your hands or

feet pinched in the seat.

(cid:1) Be careful not to hit the removed seat against a person or drop it on yourself.

the

(cid:1) After folding or installing the seat, push it forward and backward to make sure it is locked in position. When reinstalling seats to their origi- nal position, observe following precautions in order to prevent per- sonal injury in a collision or sudden stop: (cid:1) Make sure

is securely locked by pushing forward and rear- ward on the top of the seatback or by trying to pull up the edge of the bottom cushion. Failure to do so will prevent the seat belt from oper- ating properly.

the seat

89

2006 SIENNA from March ‘06 Prod. (OM45443U)

(cid:1) Make sure the seat belts are not twisted or caught under the seat and are arranged in their proper position and are ready to use.

(cid:1) Install each seat in the same posi- tion from which it was removed. Failure to do so will prevent the occupants from using seat belts properly.

(cid:1) Do not reinstall the seat with its

back facing forward.

(cid:1) Make sure

the seat

is securely

locked in the proper position.

NOTICE

Do not carry the removed seat by holding the seat position adjusting le- ver.

90

06 SIENNA_U (L/O 0603)

—Adjusting third seats (manual seat)

Lean forward and pull the strap for- ward. Then lean back to the desired angle and release the strap.

CAUTION

(cid:1) Avoid reclining

(cid:1) Align both seatbacks at the same angle when a person sits in the third seat center position. Other- wise, the person cannot wear the seat belt properly and this may cause serious injuries in a collision. the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the passengers are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt. In the event of a frontal colli- sion, the more the seat is reclined, the greater the risk of death or per- sonal injury.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Adjusting third seats (power seat)

To adjust the seatback angle, push ei- ther side of the switch. Releasing the switch will stop the seat- back at that position.

CAUTION

(cid:1) Avoid reclining

(cid:1) Align both seatbacks at the same angle when a person sits in the third seat center position. Other- wise, the person cannot wear the seat belt properly and this may cause serious injuries in a collision. the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the passengers are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt. In the event of a frontal colli- sion, the more the seat is reclined, the greater the risk of death or per- sonal injury.

—Stowing third seats (manual seat) Before stowing the third seats: (cid:1) Stow the seat belt buckles and center seat belt. (See “—Stowing seat belt buckles of the second and third seats” on page 111 and “—Stowing the center seat belt of the third seats” on page 112
in this Section.)

(cid:1) Lower the head restraint to the lowest position. See “Head restraints” on page 104 in this Section.

91

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

2. Pull and hold the seat lock release strap (“TO STOW/USE” printed on its surface) and lift up the seat rear- ward. Then push the seat down.

strap

release

If the seat does not lift up when the seat lock (“TO STOW/USE” printed on its surface) is pulled, reset as following procedure. Lift the seatback by pulling on the seat- back angle adjusting strap (“TO FOLD/ LIFT SEATBACK” printed on its surface). Then push the seatback down again.

STOWING THIRD SEATS 1. Pull

the seatback angle adjusting (“TO FOLD/LIFT SEATBACK” fold

its surface),

then

strap printed on down the seatback.

92

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

3. Push the seat against the floor and

make sure it is locked securely.

93

2006 SIENNA from March ‘06 Prod. (OM45443U)

To return the third seats, perform the following procedure. 1. Pull and hold the seat lock release strap (“TO STOW/USE” printed on its surface), then lift up the seat rear- forward and ward. Push then engage locks. Make sure the front legs are locked securely.

the seat

front

the

leg

strap

release

If the seat does not lift up when the seat lock (“TO STOW/USE” printed on its surface) is pulled, reset as following procedure. Lift the seatback by pulling on the seat- back angle adjusting strap (“TO FOLD/ LIFT SEATBACK” printed on its surface). Then push the seatback down again.

06 SIENNA_U (L/O 0603)

2. Pull

the seatback angle adjusting strap (“TO FOLD/LIFT SEATBACK” printed on its surface) and raise the seatback.

CAUTION

Do not sit on the third seat when it is in the stowed position as shown in the illustration. It may cause an acci- dent or severe injury in the event of emergency braking or collision.

94

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

When stowing or returning the seat, observe the following precautions in order to prevent personal injury: (cid:1) Make sure the seat is free of people or luggage. Then, hold the seat and slowly move it. Otherwise, people may be injured or luggage may be damaged if the seat hits them.

(cid:1) Be careful not to get your hands or

feet pinched in the seat.

(cid:1) Do not stow and return the seats when you are inside the vehicle in order to prevent pinching your hands or feet in the seat. Be sure to stow and return the seats from outside the vehicle.

When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: (cid:1) Make sure is securely locked by pushing forward and rear- ward on the top of the seatback or by trying to pull up the edge of the bottom cushion. Failure to do so will prevent the seat belt from oper- ating properly.

the seat

(cid:1) Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use.

—Folding third seats (power seat only) The third seats can be folded down au- tomatically by operating the folding/re- turning switch that is inside the back door opening on the outer edge of the ceiling. Before folding the third seats: (cid:1) Stow the seat belt buckles and center seat belt. (See “—Stowing seat belt buckles of the second and third seats” on page 111 and “—Stowing the center seat belt of the third seats” on page 112
in this Section.)

(cid:1) Lower the head restraint to the lowest restraints” on

position. page 104 in this Section.)

“Head

(See

(cid:1) Make sure that there is no object on the seat cushion. If an object is caught between the seat cushion and seatback during the operation, seat operation will stop.

95

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

1. FOLDING/RETURNING SWITCH The seatback will be folded by pushing this switch. The seatback will be returned by push- ing this switch again. 2. RETURNING SWITCH The seatback will be returned by push- ing this switch. 3. STOWING SWITCH The seats will be stow. (See “—Stowing third seats” on page 99) 4. SEATBACK ADJUSTING SWITCH The seatback will be returned by push- ing this switch. The seatback will be adjusted. “Adjusting third seats” on page 91)

(See

96

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

If an object is caught between the seat- back and seat cushion, the indicator light above the switches flashes and a beep sounds for about 10 seconds. Re- move the object before operating the seat again. If the indicator light above the switches flashes even though there is no object between the seatback and seat cushion, contact your Toyota dealer.

FOLDING THIRD SEATS Push the folding/returning switch. The seatback will fold down. If the indicator light above the switches flashes three times when the folding/re- turning switch is pushed, the folding op- eration will not start. To continue the operation, do the follow- ing: 1. Open the back door when the ignition key is in “LOCK” or “ACC” and/or the automatic transmission selector lever is in “P”.

2. Push the folding/returning switch. Seat operation will stop if any one of the switches shown in the illustrations is pushed. At this time the indicator light above the switches comes on and a beep sounds for about 10 seconds. If the engine is started during operating, the seat operation may also be stopped. To continue the folding operation, the seat- back must be back to its original position first.

Operation from outside

97

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

2. Lock

the seat

legs and push any

switch other than the stowing switch.

Seat operation will stop if any one of the switches shown in the illustrations is pushed. At this time the indicator light above the switches comes on and a beep sounds for about 10 seconds. If the engine is started during operating, the seat operation may also be stopped. To continue the returning operation, the seatback must be back to the folded posi- tion first.

CAUTION

When folding or returning the seats, observe the following precautions in order to prevent personal injury: (cid:1) Make sure that the seat path

is clear before moving the seat. Other- wise, injury may result from contact with the seat.

(cid:1) Be careful not to allow hands or feet to get caught or pinched in the seat.

to

the seats

It could result

When returning their original position, make sure the seat belts are not twisted or caught in the seatback. in serious injuries in a sudden braking or a col- lision. Do not shift the automatic transmis- sion selector lever out of “P” with the ignition key in “ON” during the operation. Doing so may cause the vehicle to move and result in serious personal injury.

2006 SIENNA from March ‘06 Prod. (OM45443U)

Operation from inside

RETURNING THIRD SEATS Push one of the switches shown in the illustrations. The seatback returns to its original position. If the indicator light above the switches three times when the switch is flashes pushed, the returning operation will not start. To continue the operation, do the follow- ing: 1. Operation from outside only—Open the back door when the ignition key is in “LOCK” or “ACC” and/or the automatic transmission selector lever is in “P”.

98

This “3RD SEAT” warning light warns the third seat operation is not yet complete when to the “ON” position.

ignition key

turned

the

is

06 SIENNA_U (L/O 0603)

—Stowing third seat (power seat) The third seats can be stowed by push- ing and holding the stowing switch that is inside the back door opening on the outer edge of the ceiling. Before stowing the third seats: (cid:1) Stow the seat belt buckles and center seat belt. (See “—Stowing seat belt buckles of the second and third seats” on page 111 and “—Stowing the center seat belt of the third seats” on page 112
in this Section.)

(cid:1) Lower the head restraint to the lowest restraints” on

position. page 104 in this Section.)

“Head

(See

(cid:1) Make sure that there is no object on the seat cushion, the seats and floor of the luggage compart- ment. If an object is caught during the operation, seat operation will stop.

floor around

99

2006 SIENNA from March ‘06 Prod. (OM45443U)

from

1. FOLDING/RETURNING SWITCH The seatback will be folded/returned. (See “Folding third seats” on page 95) 2. RETURNING SWITCH The seat will be returned the stowed position by pushing and holding this switch. 3. STOWING SWITCH The seat will be stowed by pushing and holding this switch. 4. SEATBACK ADJUSTING SWITCH The seatback will be returned. “Folding third seats” on page 95) The seatback will be adjusted. “Adjusting third seats” on page 91)

(See

(See

100

06 SIENNA_U (L/O 0603)

STOWING THIRD SEATS Push and hold the stowing switch. A beep sounds twice to indicate the start of the operation. The beep sounds again twice when the operation is com- pleted. If the indicator light above the switches flashes while the stowing switch is being pushed, the stowing operation will not start.

2006 SIENNA from March ‘06 Prod. (OM45443U)

To continue the operation, do the follow- ing: 1. Open the back door when the ignition key is in “LOCK” or “ACC” and/or the automatic transmission selector lever is in “P”.

the

indicator

2. Push and hold the stowing switch. To operation stops, light above the switches comes on and a beep sounds for about 10 seconds if any of the following condition occur during the opera- tion: (cid:1) When the stowing switch is released. (cid:1) When the folding/returning switch, re- turning switch or seatback adjusting switch the stowing switch is being pushed.

is pushed while

(cid:1) When the ignition key is turned to the “ON” position and the automatic trans- mission selector lever is moved from the “P” position.

(cid:1) When the automatic transmission selec- tor lever is in the “N” position and the ignition key is turned to the “ON” posi- tion.

If the engine is started during operating, the seat operation may also be stopped.

06 SIENNA_U (L/O 0603)

If an object is caught between the seat- back and seat cushion, the indicator light above the switches flashes and a beep sounds for about 10 seconds. Re- move the object before operating the seat again. If the indicator light above the switches flashes even though there is no object between the seatback and seat cushion, contact your Toyota dealer. If an object is caught between the seat and floor, the object prevents the seat from moving. Do not continue the op- eration. Remove the object before oper- ating the seat again. When the seat is already folded, the seat can be stowed using the same procedure. If an object is caught between the seat- back and seat cushion, the stowing opera- tion will not start.

After stowing the seats, open the flaps as shown in the illustration.

101

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

To continue the operation, do the follow- ing: 1. Open the back door when the ignition key is in “LOCK” or “ACC” and/or the automatic transmission selector lever is in “P”.

RETURNING THIRD SEATS Push and hold the returning switch un- til the seat cushion is locked. A beep sounds twice to indicate the start of the operation. Releasing the switch when the beep sounds again completes the operation automatically. If the indicator light above the switches flashes while the returning switch is being pushed, the returning operation will not start.

the

indicator

2. Push and hold the returning switch. To operation stops, light above the switches comes on and a beep sounds for about 10 seconds if any of the following condition occur during the opera- tion: (cid:1) When the returning switch is released legs are securely

the seat

before locked.

(cid:1) When the folding/returning switch, stow- ing switch or seatback adjusting switch is pushed while the returning switch is being pushed.

(cid:1) When the ignition key is turned to the “ON” position and the automatic trans- mission selector lever is moved from the “P” position.

(cid:1) When the automatic transmission selec- tor lever is in the “N” position and the ignition key is turned to the “ON” posi- tion.

102

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

If the engine is started during operating, the seat operation may also be stopped. If an object is caught between the seat and floor, the object prevents the seat from moving. Do not continue the op- eration. Remove the object before oper- ating the seat again. If the indicator light above the switches flashes even though there is no object between the seatback and seat cushion, contact your Toyota dealer.

CAUTION

When stowing or returning the seats, observe the following precautions in order to prevent personal injury: (cid:1) Make sure that the seat path

is clear before moving the seat. Other- wise, injury may result from contact with the seat.

(cid:1) Be careful not to allow hands or feet to get caught or pinched in the seat. Be sure to operate the seats from outside the vehicle.

to

the seats

in the seat.

When the indicator above the stowing switch and returning switch come on or flash, do not continue the opera- tion. An object or a person may be caught If a person is caught, serious injury may result. When returning their original position, make sure the seat belts are not twisted or caught in the seatback. in serious injuries in a sudden braking or a col- lision. Do not shift the automatic transmis- sion selector lever out of “P” with the ignition key in “ON” during the operation. Doing so may cause the vehicle to move and result in serious personal injury.

It could result

This “3RD SEAT” warning light warns the third seat operation is not yet complete when to the “ON” position.

ignition key

turned

the

is

NOTICE

Make sure that the seat path is clear before stowing or returning the seat. Otherwise, the seat cushion and seat legs may be damaged if the seat comes into contact with the luggage.

103

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Head restraints

Armrests

For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. Third seats—When an occupant sits on the seat, always pull up the head restraint to the lock position. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.

CAUTION

(cid:1) Adjust the center of the head re- straint so that it is closest to the top of your ears.

(cid:1) After adjusting the head restraint, make sure it is locked in position. the head re-

(cid:1) Do not drive with

straints removed.

To adjust the armrest, lower the armrest to the lowest position and raise it to the desired angle. Raising the armrest to the highest position unlocks the armrest to let you return it to the lowest position.

NOTICE

To prevent damage to the armrest, avoid putting heavy loads on it.

2006 SIENNA from March ‘06 Prod. (OM45443U)

Front and second seats

Third seats

104

06 SIENNA_U (L/O 0603)

Seat heaters

CAUTION

NOTICE

To turn on the seat heater, move the dial upward (“L” dial for the left front seat or “R” dial for the right front seat). At this time, the indicator light will illuminate to indicate the seat heat- er is operating. Move the dial upward or downward to ad- just to the desired temperature. To turn it off, move the dial downward until it stops. When the seat heater is not in use, move the dial fully downward. The key must be in the “ON” position to operate seat heaters.

(cid:1) Do not put unevenly weighed ob- jects on the seat and do not stick sharp objects (needles, nails, etc.) into the seat.

(cid:1) When cleaning the seats, do not use organic substances (paint thin- ner, benzine, alcohol, gasoline, etc.). They may damage the heater and seat surface.

(cid:1) To prevent the battery from being discharged, turn the switch off when the engine is not running.

the seat heater because

Occupants must use caution when op- erating it may make them feel too hot or cause burns at low temperatures (erythema, varicella). Use extra caution for; (cid:1) Babies, small children, elderly per- sons, sick persons or persons with physical disabilities

(cid:1) Persons who have sensitive skin (cid:1) Persons who are exhausted (cid:1) Persons who have taken alcohol or drugs which induce sleep (sleeping drug, cold remedy, etc.)

To prevent the seat from overheating, do not use the seat heater with a blanket, cushion, or other insulating objects which cover the seat.

105

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Do not allow any children to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious in- jury or death during emergency braking or a collision. Also, do not let the child sit on your lap. Holding a child in your arms does not provide sufficient restraint. Pregnant woman. Toyota recommends the use of a seat belt. Ask your doctor for specific lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Toyota recommends the use of a seat belt. Depending on the inju- ry, first check with your doctor for specific recommendations.

recommendations. The

Seat belts— —Seat belt precautions Toyota strongly urges that the driver and passengers in the vehicle be properly re- strained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents. The seat belts provided for your vehicle are designed for people of adult size, large enough to properly wear them. Child. Use a child restraint system ap- propriate for the child until the child be- comes large enough to properly wear the vehicle’s seat belts. See “Child restraint” on page 137 in this Section for details. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid infla- tion of the airbag may cause death or serious injury to the child.

106

CAUTION

the vehicle

(cid:1) Avoid reclining

in their seats Persons should ride their seat belts properly wearing whenever is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision. When using the seat belts, observe the following: (cid:1) Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may In the contact the shoulder belt. event of a the more the seat is reclined, the great- er the risk of death or personal in- jury.

frontal collision,

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

(cid:1) Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or doors.

(cid:1) Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be re- placed. Do not disassemble or modify the system.

—Fastening front and rear seat belts

Tab

Buckle

(cid:1) Keep the belts clean and dry.

If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive clean- ers, or allow them to come into the belts—they may contact with severely weaken (See “Cleaning the interior” on page 447
in Section 5.)

the belts.

(cid:1) Replace the belt assembly (includ- ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.

tab

the

into

insert

Adjust the seat as needed and sit up straight and well back in the seat. To fasten your belt, pull it out of the re- tractor and the buckle. You will hear a click when the tab locks into the buckle. The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.

is

then

When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” on page 137 in this Section.) To free the belt again, fully retract the belt and then pull the belt out once more. If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor.

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from death or serious injury.

107

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Take up slack

Too high

CAUTION

(cid:1) Both high- positioned lap belts and loose- fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on hips as possible.

(cid:1) Do not place the shoulder belt un-

der your arm.

Keep as low on hips as possible

the

lap and

the position of

Adjust shoulder belts. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit by pulling the shoulder portion upward through the latch plate.

108

Seat belts for seats with outside arm- rests— Fasten your belt, ensuring that the shoul- der portion of the belt passes over the top of the outside armrest and that the lap portion of the belt passes under the out- side armrest as shown.

CAUTION

Always wear the belt with the shoul- der portion over the outside armrest and the lap portion under the outside armrest. Failure to do so may in- crease the chance of injury in an ac- cident.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause serious injuries in a collision.

Seat belts with an adjustable shoulder anchor— Adjust the shoulder anchor position to your size. To raise: Slide the anchor up. To lower: Push in the lock release button and slide the anchor down. After adjustment make sure the anchor is locked in position.

To release the belt, press the buckle release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.

109

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

located and securely

Make sure the both buckles are cor- rectly latched. Failure to properly match the buckle and tab may cause serious injury in case of an accident or a collision.

CENTER SEAT BELT OF THE THIRD SEATS The center seat belt of the third seats is a 3- point type restraint with 2 buckles. Both seat belt buckles must be correctly located and securely for proper operation. Make sure buckle 1 is securely latched for ready use of the center seat belt of the third seats.

latched

110

Two buckles and tabs for center seat belt of the third seats The to prevent the belt from being buckled in the wrong place.

tabs have different shapes

two

Buckle 1—Matches hooked end Buckle 2—Matches concave end

the

tab with

the

the

tab with

the

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)