2006 Toyota Sienna Owners Manual

(cid:1) Operates with the power sliding door

switches inside the vehicle

(cid:1) Operates with the wireless remote con-

trol transmitter

(cid:1) Assists operation with the outside or

inside handle by hand

the

The power sliding door system can be canceled by “SLIDE DOOR OFF” switch. When the power sliding door system is on, if you put the transmission out of “P” with the ignition key in the “ON” position and is not completely closed, a buzzer will sound.

the sliding door

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the sliding door automatically opens or closes.

(cid:1) Never allow a child to operate the

sliding door.

29

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

NOTICE

Do not apply excessive force when the sliding door is operated automati- cally. Otherwise, the power sliding door system may be damaged.

You can cause a beep to sound when the power sliding door is opened or closed. For details, contact your Toyota dealer.

Front overhead console

OPERATING WITH THE POWER SLIDING DOOR SWITCHES To open the door, push the switch. To close the door, push the switch once again. The door opens and closes com- pletely. Switches on the front overhead con- sole:

” switch—To operate

“ door

the

left side

” switch—To operate the right side

“ door

Switches on the center pillar:

“PWR DOOR” switch—To operate each side door

Opening operation can be performed by the switches under the following condi- tions: (cid:1) The sliding door is unlocked. (cid:1) The power sliding door system is on. is

“SLIDE DOOR OFF” switch

(The pushed out.)

Center pillar

(cid:1) The sliding door is between the fully- closed position and half- opened posi- tion.

30

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

CAUTION

If you shift the automatic transmis- sion selector lever out of “P” and accelerate before the power sliding door is closed completely, the sliding door may reverse to the open posi- tion. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you start driving.

(cid:1) When the ignition key is in the “ON” position, the transmission selector lever must be in “P”.

(cid:1) The

child- protector

is

unlocked.

(switches on the center pillar only)

Closing operation can be performed by the switches under the following condi- tions: (cid:1) The power sliding door system is on. is

“SLIDE DOOR OFF” switch

(The pushed out.)

(cid:1) The sliding door is between the fully- opened position and half- opened posi- tion.

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened. The length of time required to push the switches for operating the sliding door can be changed. For details, contact your Toyota dealer.

” or “

THE WIRELESS

OPERATING WITH REMOTE CONTROL TRANSMITTER To open or close the door, push the ” switch on the wireless “ remote control transmitter about one second. (Only when the power sliding door system is on.) For details, see “Wireless remote control” on page 14
in this Section. ASSISTS THE OUTSIDE OR INSIDE HANDLE BY HAND When the power sliding door system is on (the “SLIDE DOOR OFF” switch is pushed out), if you pull the outside handle or slide the the sliding door will automatically and completely open or close. When the power sliding door system is off, the sliding door can be operated manually by the outside or inside handle.

OPERATION WITH

inside handle,

31

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

inside or outside handle and

CLOSING THE FULLY- OPENED SLIDING DOOR To close the fully- opened sliding door, pull the then close the door. Sliding door closer: When the sliding door has not been fully closed, it is auto- matically closed completely even the power sliding door system is off.

if

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the automatically closes when it has not been fully closed.

sliding

door

(cid:1) Never allow a child to operate the

sliding door.

NOTICE

Do not apply excessive force when the sliding door closer is operating. Otherwise, the sliding door closer may be damaged.

32

Before operating the power sliding door, make sure there is nobody near the slid- ing door. Make sure the sliding door stops at the fully- opened position, and then al- low the passengers to get in and out of the vehicle. The resistance must be as strong as the force of the moving door, or stronger. As the sliding door approaches fully- closed or fully- opened position, its moving force increases significantly. The jam protection function may not work if something gets caught just before the sliding door is fully closed. If the sliding door receives a strong im- pact, this function may operate even if nothing is caught.

the

CAUTION

The power sliding door could injure people if they are caught in the door path. When using the power sliding door, observe the following: (cid:1) Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a serious injury.

JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power sliding door while it is closing or opening, the sliding door will automatically reverse to the opposite di- rection. However, if the power sliding door is between fully- opened positions while it is opening, the door will stop at that position. If function operates continuously at the closing operation more than 2 the sliding door will be stopped at that position and the power sliding door system will be canceled.

the half- opened and

jam protection

times,

the

2006 SIENNA from March ‘06 Prod. (OM45443U)

(cid:1) The

jam protection

function may not work if something gets caught just before the sliding door is fully closed.

(cid:1) Before you close the power sliding door, always make sure there is no- body around it. Also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught in a closing door, it could result injury. When anyone closes the power slid- ing door, make sure he or she oper- ates the door safely.

in death or serious

the vehicle.

inside

NOTICE

Objects caught in the path of the slid- ing door may be damaged. Make sure there is nothing in the doorway be- fore closing the sliding door.

06 SIENNA_U (L/O 0603)

—Power sliding door cautions

In any of

the battery.

If the battery is disconnected or run down, the power sliding door system may not work after you reconnect, replace or recharge these cases, close the sliding doors completely by hand to normalize the power sliding door system. If the power sliding door system does not operate properly after the above proce- dure, there may be a problem in the sys- tem. Contact your Toyota dealer.

CAUTION

(cid:1) When closing the sliding door, con- firm safety of the area around. Keep the heads, hands and other parts of the bodies of all occupants away from the sliding door. Other- wise, the closing door may cause an unexpected serious injury.

the door will slide

(cid:1) When the vehicle is stopped on a slope, faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door.

33

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

the door

(cid:1) When stopping on a downward slope, open fully while passengers are getting on or off. Do not pull the outside handle or inside handle while is open as the door could suddenly close by itself causing injury.

the door

NOTICE

Do not close the sliding door by ap- plying the brakes. Doing so could cause the door to be damaged.

When the fuel filler door is opened, the left side sliding door will not open. Close the fuel filler door securely and then operate the sliding door.

NOTICE

Avoid forcibly opening the left side sliding door fully when the fuel filler door is opened. Otherwise, the fuel filler door may be damaged.

the sliding door window

When is opened more than about 15 cm (6 in.), the sliding door will stop at half- opened position reasons. Close the window and then operate the sliding door.

for safety

34

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Sliding door child- protectors

CAUTION

Make sure to turn off the power slid- ing door system after the child- protectors.

locking

Open the sliding door fully and move the lock lever to the “LOCK” position as shown on the label. Then close the sliding door. When the child- protector is locked, you cannot open the sliding door by the inside door handle. We recommend using this feature whenever small children are in the vehicle.

CAUTION

When the power sliding door is ON— Do not leave the sliding door at half- opened position because the door will unlock after 30 minutes. If the vehicle is stopped on a downward slope, it may move and cause an unexpected injury. When is OFF—Do not leave the sliding door at half- opened position because the door is not latched at this position. If the vehicle is stopped on a down- ward slope, it may move and cause an unexpected injury.

the power sliding door

NOTICE

When the power sliding door is ON— To prevent the battery from being dis- charged, do not leave the sliding door at half-opened position.

35

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Back door (non- powered)

lights and

front personal

When all the side doors and back door are unlocked simultaneously with a key, the ignition switch light will come on and remain on for about 15 seconds before fading out. (For details, see “Front personal lights” on page 176 and “Ignition switch light” on page 179 in Section 1- 5.) If the back door opener does not operate, see “If you cannot operate back door opener” on page 440 in Section 4. If the battery is disconnected or run down, the back door will be automatically locked after you reconnect, replace or re- charge the battery. Be careful not to lock your keys in the vehicle.

When closing the back door, the inside strap can be used to make the reach easier. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See “—Stowage precautions” on page 399
in Section 2 for precautions when loading luggage.

To open the back door, push up the back door opener and raise the door. The back door can be opened when the vehicle is stopped. The back door can be locked or unlocked in the following ways. (cid:1) Operate

lock switch. (See “Front doors” on page 22 in this Section.) (cid:1) Operate

remote control. (See “Wireless remote control” on page 14 in this Section.)

the power door

the wireless

(cid:1) All the side doors and back door are locked and unlocked simultaneously with “Front doors” on page 22 in this Section.)

the driver’s door.

(See

36

2006 SIENNA from March ‘06 Prod. (OM45443U)

CAUTION

Keep the back door closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.

NOTICE

To avoid damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.

06 SIENNA_U (L/O 0603)

Power back door— —“BACK DOOR OFF” switch

On

Off

This switch is used to turn on and off the power back door system. In order to operate the power back door, the “BACK DOOR OFF” switch on the in- strument panel must be pushed out. (The orange line on top of the switch indicates that the power back door sys- tem is on.) To disable the power back door feature, push in the switch.

CAUTION

(cid:1) Do not leave small children or pets unattended in your vehicle. They could operate the power back door, and anyone around the back door could be injured. Turn off the power back door system when the power back door is not in use.

(cid:1) When jacking up the vehicle, turn off the power back door system and close the back door completely.

NOTICE

When your vehicle goes through an automatic car wash, make sure the power back door system is off.

37

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Automatic operation (power back door—ON) The power back door can be operated automatically in the following ways: (cid:1) Operates with

the power back door

switch on the overhead console

(cid:1) Operates with the wireless remote con-

trol transmitter

NOTICE

Do not apply excessive force when the back door is operated automati- cally. Otherwise, the power back door system may be damaged.

is

the

system

canceled,

(cid:1) Assists closing by hand The power back door system can be can- celed by the “BACK DOOR OFF” switch. When see “—Manual operation” on page 41 in this Section. When closing or opening the back door automatically, two beeps will be heard and the turn signal lights will flash twice. The beep sound can be changed. For de- tails, contact your Toyota dealer.

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the back door automatically closes. (cid:1) Never allow a child to operate the

back door.

38

OPERATING WITH THE POWER BACK DOOR SWITCH To open the door, push and hold the ” switch on the overhead con- “ sole about one second. To close the door, push this switch once again. The door opens and closes completely.

2006 SIENNA from March ‘06 Prod. (OM45443U)

Opening operation can be performed by the switch under the following condi- tions: (cid:1) The back door is unlocked. (cid:1) The power back door system

“BACK DOOR OFF” switch

is on. is

(The pushed out.)

(cid:1) The back door is between in the fully- closed position and half- opened posi- tion.

(cid:1) When the ignition key is in the “ON” position, the transmission selector lever must be in “P”.

Closing operation can be performed by the switch under the following condi- tions: (cid:1) The power back door system

“BACK DOOR OFF” switch

is on. is

(The pushed out.)

(cid:1) The back door is between in the fully- opened position and half- opened posi- tion.

The time of pushing the switches for oper- ating the back door can be changed. For details, contact your Toyota dealer.

06 SIENNA_U (L/O 0603)

(Only when

THE WIRELESS

OPERATING WITH REMOTE CONTROL TRANSMITTER To open or close the door, push and ” switch on the wireless hold the “ remote control transmitter about one second. the power back door system is on.) For details, see “Wireless remote control” on page 14
in this Section. ASSISTS CLOSING BY HAND When the power back door system is on (the “BACK DOOR OFF” switch is pushed out), if you move the back door about 10—15 cm (4—6 in.) from its fully- opened position, the back door will automatically and completely close. When the power back door system is off, the back door can be closed manually. The assisting function when closing the back door can be disabled and the assist- ing function when opening the back door can be added. For details, contact your Toyota dealer.

JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power back door while it is closing or opening, the back door will au- tomatically reverse to the opposite direc- tion. If function operates continuously at the closing operation more than 2 the back door will be stopped at that position.

jam protection

times,

the

39

2006 SIENNA from March ‘06 Prod. (OM45443U)

Before operating the power back door, make sure there is nobody near the back door. The resistance must be as strong as the force of the moving door, or stronger. As the back door approaches the fully- closed or fully- opened position, its moving force increases significantly. The jam protection function may not work if something gets caught just before the back door is fully closed. If the back door receives a strong impact, this function may operate even if nothing is caught.

06 SIENNA_U (L/O 0603)

If the battery is disconnected or run down, the back door will be automatically locked and the power back door system may not work after you reconnect, replace or recharge the battery. In any of these cases, normalize the power back door system by following procedure. 1. Unlock

the key, wireless remote control transmitter or power door lock switch.

the back door with

2. Close hand.

the back door completely by

If the power back door system does not operate properly after the above proce- dure, there may be a problem in the sys- tem. Contact your Toyota dealer.

CAUTION

The power back door could injure people if they are caught in the door path. When using the power back door, observe the following: (cid:1) Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a serious injury.

(cid:1) The

jam protection

function may not work if something gets caught just before the sliding door is fully closed.

(cid:1) Before you close the power back door, always make sure there is no- body around it. If someone’s neck, head or hands get caught in a clos- ing door, it could result in death or serious injury. When anyone closes the power back door, make sure he or she operates the door safely.

NOTICE

Objects caught in the path of the back door may be damaged. Make sure there is nothing in the doorway before closing the back door.

40

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Manual operation (power back door—OFF)

lights and

front personal

When all the side doors and back door are unlocked simultaneously with a key, the ignition switch light will come on and remain on for about 15 seconds before fading out. (For details, see “Front personal lights” on page 176 and “Ignition switch light” on page 179 in Section 1- 5.) If the back door opener does not operate, see “If you cannot operate back door opener” on page 440 in Section 4. If the battery is disconnected or run down, the back door will be automatically locked after you reconnect, replace or re- charge the battery. Be careful not to lock your keys in the vehicle.

When closing the back door, the inside strap can be used to make the reach easier. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See “—Stowage precautions” on page 399
in Section 2 for precautions when loading luggage.

To open the back door, push up the back door opener and raise the door. The back door can be opened when the vehicle is stopped. The back door can be locked or unlocked in the following ways. (cid:1) Operate

lock switch. (See “Front doors” on page 22 in this Section.) (cid:1) Operate

remote control. (See “Wireless remote control” on page 14 in this Section.)

the power door

the wireless

(cid:1) All the side doors and back door are locked and unlocked simultaneously with “Front doors” on page 22 in this Section.)

the driver’s door.

(See

41

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Power windows

CAUTION

Keep the back door closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.

NOTICE

To avoid damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.

Back door closer: When the back door has not been fully closed, it is automati- cally closed completely even if the power back door system is off.

CAUTION

(cid:1) Careful attention is needed so as not to get your fingers trapped as the back door automatically closes when it has not been fully closed. (cid:1) Never allow a child to operate the

back door.

NOTICE

Do not apply excessive force when the back door closer is operating. Otherwise, the back door closer may be damaged.

The windows can be operated with the switch on each front door. The power windows work when the ignition key is in the “ON” position. Key off operation: If both front doors are closed, the front door windows and sliding door windows work for 43 seconds even after the ignition switch is turned off. It stops working when either front door is opened.

42

2006 SIENNA from March ‘06 Prod. (OM45443U)

OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Lightly pull up the switch.

06 SIENNA_U (L/O 0603)

Automatic operation: Type A—Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it. Type B—Push the switch completely down or pull it completely up, and then release it. The window will fully open or close. To stop the window partway, lightly move the switch in the opposite direction and then release it. Jam protection function (type B only): During automatic closing operation, the window stops and opens half way if some- thing gets caught between the window and window frame. If the window receives a strong impact, this function may work even if nothing is caught.

43

2006 SIENNA from March ‘06 Prod. (OM45443U)

Type A (to open only)

Type B (to open and close)

06 SIENNA_U (L/O 0603)

Window lock switch

If the battery is disconnected or run down, the power window may not operate automatically and the jam protection func- tion will not function correctly after you reconnect, replace or recharge the battery. In any of these cases, you should normal- ize the power window. To normalize the power window: 1. Push down the power window switch

and lower the window halfway.

2. Pull up

the switch until

the window closes and hold the switch for a sec- ond.

that

Make sure the window opens and closes automatically. If the power window cannot be operated properly, have it checked by your Toyota dealer.

CAUTION

(cid:1) Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a serious injury.

(cid:1) The

jam protection

function may not work if something gets caught just before fully closed.

the window

is

44

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

THE

PASSENGERS’

OPERATING WINDOWS Use the switch on each passenger’s door or the switches on the driver’s door that control each passenger’s win- dow. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passengers’ windows cannot be operated. The sliding door window cannot be oper- ated when the sliding door is opened.

CAUTION

To avoid serious personal injury, you must do the following. (cid:1) Before you close the power win- dows, always make sure there is nobody around the power windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it could result in death or serious in- jury. When anyone closes the power windows, make sure he or she op- erates the windows safely.

in a closing window,

the vehicle.

inside

(cid:1) When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.

them

(cid:1) Be sure to remove the ignition key

when you leave your vehicle.

(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power window switches and get in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.

trapped

45

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Manual quarter windows

Power quarter windows

Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either is opened.

front door

CAUTION

To open the quarter window, pull the latch handle toward you and swing it fully out. When closing the window, make sure it is completely closed.

The quarter windows can be operated with the “REAR VENT” switch on the instrument panel. The power quarter windows work when the ignition key is in the “ON” position. To open: Push the switch on the upper side. To close: Push the switch on the lower side. Both the left and right rear quarter win- dows move as the switch.

long as you hold

46

To avoid serious personal injury, you must do the following. (cid:1) Before you close the power quarter windows, always make sure there is nobody around the power quarter windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it could result in death or serious in- jury. When anyone closes the power windows, make sure he or she op- erates the windows safely.

in a closing window,

the vehicle.

inside

(cid:1) When small children are in the ve- hicle, never let them use the power quarter window switches without supervision.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Hood

(cid:1) Be sure to remove the ignition key

when you leave your vehicle.

(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power quarter window switch and get trapped in a window. Unattended person (particularly a small child) can be involved in a serious accident.

To open the hood: 1. Pull the hood lock release lever. The

hood will spring up slightly.

CAUTION

Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.

2. In front of the vehicle, pull up the the

lever and

lift

auxiliary catch hood.

47

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Theft deterrent system

CAUTION

After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.

NOTICE

Be sure to return the support rod to its clip before closing the hood. Clos- ing the hood with the support rod up could cause the hood to bend.

3. Hold the hood open by inserting the

support rod into the slot.

To insert the support rod into the slot, move it straight up. If it is moved to the side or toward the inside of the vehicle, it may become detached. Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood and make sure it locks into place. If necessary, press down gently on the front edge to lock it.

the support rod

to

48

To deter the vehicle theft, the system is designed to sound an alarm if any of the side doors, back door or hood is forcibly unlocked or opened or the bat- tery terminal is disconnected and then reconnected when the vehicle is locked. The alarm blows the horn intermittently and flashes the headlights, tail lights and turn signal lights, and turns on the front personal lights.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

The system will automatically be set after 30 seconds. When the system is set, the indicator light will start flashing again. 4. After making sure

light starts flashing, you may leave the ve- hicle.

indicator

the

Never leave anyone in the vehicle when you set the system, because unlocking from the inside will activate the system. CANCELING THE SYSTEM The system can be canceled by the fol- lowing ways: (cid:1) Any of the side doors or the back door is unlocked with the key or wireless remote control transmitter.

for 2 seconds when

(cid:1) Turn the ignition key to “ON” position. If the parking lights and tail lights come on is canceled, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

the system

WHEN THE SYSTEM IS SET Activating the system The system will sound the alarm under the following conditions: (cid:1) If any of the side doors or back door is unlocked or opened without the key or wireless remote control transmitter, or if the hood is forcibly opened.

(cid:1) If the battery terminal is disconnected

and then reconnected.

(cid:1) If the ignition is hotwired. The indicator light will come on when the system is activated. If the alarm has been activated and any of the side doors or back door is un- locked, all the side doors and back door will re- lock automatically. After one minute, the alarm will automati- cally stop and the indicator light will starts flashing again. Reactivating the system Once set, the system is automatically re- set after the alarm stopped automatically after one minute. The alarm will activate again under the same in circumstances “Activating the system”.

described

49

2006 SIENNA from March ‘06 Prod. (OM45443U)

SETTING THE SYSTEM 1. Turn

the ignition key position and remove it.

to the “LOCK”

the

On some models, the indicator light will start flashing when the key is removed from “Engine immobilizer system” on page 13 in this Section for details.) 2. Have all passengers get out of

ignition switch.

(See

the

vehicle.

3. Close and lock all the side doors, back

door and hood.

The indicator light will remain on when all the side doors, back door and hood are closed and locked.

06 SIENNA_U (L/O 0603)

Fuel tank cap

TESTING THE SYSTEM 1. Open all the windows. 2. Set the system as described above. All the side doors and back door should be locked with the key or wireless re- mote control to wait until the indicator light starts flash- ing.

transmitter. Be sure

3. Unlock any side door from the inside. The system should activate the alarm.

for

this operation

4. Stop the alarm as described above. 5. Repeat

the other doors and hood. When the hood, also check that the system is activated when the battery terminal is disconnected and then reconnected. the system does not work properly,

If have it checked by your Toyota dealer.

testing

This indicates that the fuel filler door is on the left side of your vehicle.

Stopping the alarm The alarm will be stopped by the following these ways: (cid:1) Unlock any of the side doors or the back door with the key or wireless re- mote control transmitter.

(cid:1) Turn the ignition key from the “LOCK”

to “ON” position.

the

the system at

These ways cancel same time. If the battery becomes discharged due to the vehicle being unused for a long time, etc., when the battery is recharged or the alarm. If this happens, immediately unlock any of the side doors or the back door with the key or the wireless remote con- trol transmitter, and the alarm will stop.

the system will give

replaced,

50

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

NOTICE

Avoid opening the fuel filler door when the left side sliding door is fully opened. Otherwise, the fuel filler door may be damaged.

2. To remove the fuel tank cap, turn the cap counterclockwise by 90 de- grees (to the pressure point 1), and then turn it an additional 30 degrees (to point 2). Pause slightly before removing it.

It is not unusual to hear a slight swoosh when the cap is opened.

51

2006 SIENNA from March ‘06 Prod. (OM45443U)

1. To open the fuel filler door, pull the

lever up. When refueling, turn off the engine.

CAUTION

(cid:1) Do not smoke, cause sparks or al- flames when refueling.

low open The fumes are flammable.

(cid:1) When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck is suddenly re- moved.

the cap

if

06 SIENNA_U (L/O 0603)

Electric moon roof

When installing the cap, turn the cap clockwise until you hear one click. When you hear the click, the cap is fully closed. If the cap is not installed securely, the malfunction lamp comes on. Make sure the cap is tightened securely. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

indicator

CAUTION

Sliding operation

(cid:1) Make sure the cap is installed se- in

curely to prevent fuel spillage the event of an accident.

(cid:1) Use only a genuine Toyota fuel tank cap for replacement. It is designed to regulate fuel tank pressure.

NOTICE

To prevent damage to the cap, apply force only in the turning direction to the cap. Do not pull or pry it.

Tilting operation

2006 SIENNA from March ‘06 Prod. (OM45443U)

3. The removed cap can be stored on the back side of the fuel filler door. Position the cap so that the hooks point to the left and right, and set it in the receptacle on the back side of the door.

52

06 SIENNA_U (L/O 0603)

the

the moon roof, use

To operate switch on the overhead console. The moon roof works when the ignition key is in the “ON” position. The sun shade can be opened or closed by hand. Sliding operation— To open: Push the switch on the “SLIDE OPEN” side. The roof will fully open automatically. To stop the roof partway, push the switch on either the “SLIDE OPEN” or “TILT UP” side quickly. When you quickly push and release the switch, the moon roof will open while the switch is being pushed and stop when released. The sun shade will be opened together with the roof. When the moon roof is opened fully, the deflector will raise to reduce the entering of the strong wind. The angle of the de- flector will be adjusted according to the vehicle speed. To close: Push the switch on the “TILT UP” side.

The roof will fully close automatically. To stop the roof partway, push the switch on either the “SLIDE OPEN” or “TILT UP” side quickly. When you quickly push and release the switch, the moon roof will close while the switch is being pushed and stop when released. Tilting operation— To tilt up: Push the switch on the “TILT UP” side. The roof will fully tilt up automatically. To stop the roof partway, push the switch on either the “SLIDE OPEN” or “TILT UP” side quickly. When you quickly push and release the switch, the moon roof will tilt up while the switch is being pushed and stop when released. To tilt down: Push “SLIDE OPEN” side. The roof will fully tilt down automatically. To stop the roof partway, push the switch on either the “SLIDE OPEN” or “TILT UP” side quickly. When you quickly push and release the switch, the moon roof will tilt down while the switch is being pushed and stop when released.

the switch on

the

Key off operation: If both front doors are closed, it works for 43 seconds even after the ignition switch is turned off. It stops working when either front door is opened. Jam protection function: (cid:1) If something gets caught between the moon roof and frame during slide clos- ing operation, the moon roof stops and opens half way, and the deflector stops and raises fully.

(cid:1) If something gets caught between the moon tilting down operation, the moon roof stops and opens fully.

frame during

roof and

If the moon roof receives a strong impact, this function may work even if nothing is caught. If the moon roof does not operate auto- matically or the jam protection function does not operate correctly, you should normalize the moon roof. To normalize the moon roof, push and hold the switch on the “TILT UP” side until the moon roof tilts all the way up and then tilts down a little automatically.

53

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

(cid:1) Be sure to remove the ignition key

when you leave your vehicle.

(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power window switches and get in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.

trapped

(cid:1) Never sit on

top of

the vehicle

around the roof opening.

(cid:1) Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a serious injury.

(cid:1) The

jam protection

function may not work if something gets caught just before the moon roof is fully closed.

Make sure that the moon roof opens and closes automatically. If the moon roof can- not be operated properly, have it checked by your Toyota dealer.

CAUTION

To avoid serious personal injury, you must do the following. (cid:1) While the vehicle is moving, always keep the heads, hands and other parts of the bodies of all occupants away from the roof opening. Other- wise, they could be seriously in- jured if the vehicle stops suddenly or if the vehicle is involved in an accident.

(cid:1) Before you close the moon roof, always make sure there is nobody around the moon roof. You must also make sure nobody places his or her head, hands and other parts of the body in the roof opening. If someone’s neck, head or hands get caught in the closing roof, it could result injury. When anyone closes the moon roof, first make sure it is safe to do so.

in death or serious

54

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

SECTION 1- 3

OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats Front seats Driving position memory system Rear seats Head restraints Armrests Seat heaters Seat belts SRS airbags Child restraint

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

56
56
63
65
104
104
105
106
118
137

55

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Seats While the vehicle is being driven, all ve- hicle occupants should have the seatback upright, sit well back in the seat and prop- erly wear the seat belts provided.

CAUTION

(cid:1) Do not drive the vehicle unless the occupants are properly seated. Do not allow any passengers to sit on top of a folded- down seatback, or in the luggage compartment or car- go area. Persons not properly seated and/or not properly re- strained by seat belts can be se- verely injured in the event of emer- gency braking or a collision.

(cid:1) During driving, do not allow any passengers to stand up or move around between seats. Otherwise, severe the event of emergency braking or a collision.

injuries can occur

in

Front seats— —Front seat precautions Driver seat

CAUTION

The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (“NHTSA”) advises: Since the risk zone for driver airbag is the first 50—75 mm (2—3 in.) of inflation, placing yourself 250 mm (10
in.) from your driver airbag provides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 250
mm in.) away now, you can change your driving position in sever- al ways: (cid:1) Move your seat to the rear as far as you can while still reaching the pedals comfortably.

(10

56

(cid:1) Slightly recline

the back of

the seat. Although vehicle designs vary, many drivers can achieve the 250
mm (10 in.) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non- slippery cushion, or raise the seat if your vehicle has that feature.

(cid:1) If your steering wheel is adjustable, tilt it downward. This points the air- bag toward your chest instead of your head and neck.

The seat should be adjusted as rec- ommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

Front passenger seat

Front seats (with SRS side airbags)

CAUTION

CAUTION

The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury es- pecially if the front passenger is very close to the airbag. The front passen- ger seat should be as far from the airbag as possible with the seatback adjusted, so the front passenger sits upright.

The SRS side airbags are installed in the driver and front passenger seats. Observe the following precautions. (cid:1) Do not lean against the front door when the vehicle is in use, since the side airbag inflates with consid- erable speed and force. Otherwise, you may be killed or seriously in- jured.

(cid:1) Do not use seat accessories which cover the area where the side air- bags inflate. Such accessories may prevent the side airbags from acti- vating correctly, causing death or serious injury.

(cid:1) Do not modify or replace the seats or upholstery of the seats with side airbags. Such change may prevent the side airbag system from activat- ing correctly, disable the system or cause the side airbags to inflate ac- cidentally, resulting in death or seri- ous injury.

—Seat adjustment precautions

CAUTION

(cid:1) Do not adjust the seat while the vehicle is moving as the seat may unexpectedly move and cause the driver to lose control of the vehicle. (cid:1) Be careful that the seat does not

hit a passenger or luggage.

(cid:1) After adjusting the seat position, re- lease the lever and try sliding the seat forward and backward to make sure it is locked in position.

(cid:1) After adjusting the seatback, push your body back against the seat to make sure the seat in position.

locked

is

interfere with

(cid:1) Do not put objects under the seats except for putting them in the auxil- the objects iary box. Otherwise, may the seat- lock mechanism or unexpectedly push up the seat position adjusting lever and the seat may suddenly move, causing the driver to lose control of the vehicle.

57

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Adjusting driver’s seat (manual seat)

(cid:1) While adjusting the seat, do not put your hands under the seat or near the moving parts. Otherwise, your hands or fingers may be caught and injured.

1. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. 2. SEAT HEIGHT ADJUSTING KNOB To change the seat height, turn the knob either way. 3. SEATBACK

ADJUSTING

ANGLE

LEVER

lever up. lean back to the desired angle

Lean forward and pull the Then and release the lever.

58

2006 SIENNA from March ‘06 Prod. (OM45443U)

CAUTION

reclining

Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- der belt. In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or personal injury.

4. SEAT

LUMBAR

SUPPORT

ADJUSTING KNOB

To change the amount of lumbar sup- port, turn the knob either way.

06 SIENNA_U (L/O 0603)

—Adjusting driver’s seat (power seat)

1. SEAT POSITION, SEAT CUSHION HEIGHT

SEAT

ANGLE ADJUSTING SWITCH

AND

Move the control switch in the desired direction. Releasing the switch will stop the seat at that position. Do not place anything under front seats, as this might interfere with the seat movement. 2. SEATBACK

ADJUSTING

ANGLE

the

SWITCH

Move the control switch in the desired direction. Releasing the switch will stop the seat- back at that position.

59

2006 SIENNA from March ‘06 Prod. (OM45443U)

CAUTION

reclining

Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- der belt. In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or personal injury.

3. SEAT

LUMBAR ADJUSTING SWITCH

SUPPORT

Press either side of the switch. The amount of lumbar support will change while the switch is pressed.

60

06 SIENNA_U (L/O 0603)

—Adjusting front passenger’s seat (manual seat)

1. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. 2. SEATBACK

ADJUSTING

ANGLE

LEVER

lever up. lean back to the desired angle

Lean forward and pull the Then and release the lever.

CAUTION

reclining

Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- In the event of a frontal der belt. collision, the more the seat is re- clined, the greater the risk of death or personal injury.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

—Adjusting front passenger’s seat (power seat)

3. SEATBACK FOLDING LEVER

some models)

(on

front passenger’s seat can be

The folded down using this lever.

1. SEAT POSITION ADJUSTING SWITCH Move the control switch in the desired direction. Releasing the switch will stop the seat at that position. Do not place anything under front seats, as this might interfere with the seat movement. 2. SEATBACK

ADJUSTING

ANGLE

the

SWITCH

Move the control switch in the desired direction. Releasing the switch will stop the seat- back at that position.

61

2006 SIENNA from March ‘06 Prod. (OM45443U)

CAUTION

reclining

Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- der belt. In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or personal injury.

62

06 SIENNA_U (L/O 0603)

—Folding front passenger’s seat

1. Pull the seatback angle adjusting le- ver and raise the seatback to its up- right position.

2. Pull the seatback folding lever and

fold the seatback down.

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

NOTICE

To prevent damage to the seat, avoid putting heavy loads on the temporary table.

Driving position memory system This system can memorize the position of the driver’s seat and outside rear view mirrors, and recall them at the touch of a button. Buttons “1” and “2” can memorize two separate positions.

You can use the seatback as a temporary table only when the vehicle is stopped.

CAUTION

To avoid serious injury: (cid:1) Do not set up the seatback table

while the vehicle is moving.

(cid:1) Do not sit on the folded seatback. front passenger’s (cid:1) Make sure seat is securely locked in sliding position when you set the seat as a temporary table.

the

63

2006 SIENNA from March ‘06 Prod. (OM45443U)

06 SIENNA_U (L/O 0603)

To make only slight changes to an already memorized position, the easiest way is to first activate the memorized position, then make the desired changes and perform step 2 above.

RECALLING THE MEMORIZED POSITION When you push button “1” or “2”, a beep will sound and the driving posi- tion will be automatically adjusted to the position recorded for that button. The memorized position can be recalled under the following conditions: (cid:1) The ignition key is in the “ON position and the automatic transmission selector lever is in the “P” position.

(cid:1) The key is not in the ignition switch and less than 30 seconds have passed since opening the driver’s door.

2006 SIENNA from March ‘06 Prod. (OM45443U)

SETTING THE DRIVING POSITION The key must be in the “ON” position and the automatic transmission selector lever is in the “P” position. 1. Adjust the driver’s seat and outside the desired

to

rear view mirrors position.

2. While pushing

the “SET” button, push button “1” or “2” until a beep is heard.

The system can memorize up to 2 posi- tions by repeating the above steps. If step 2 is performed when both buttons “1” and “2” are memorized, the previous position will be erased and a new position will be set.

64

06 SIENNA_U (L/O 0603)

Rear seats— —Rear seat precautions

CAUTION

(cid:1) Adjustment should not be made

while the vehicle is moving.

(cid:1) Be careful that the seat does not

hit a passenger or luggage.

(cid:1) After adjusting the seat position, try sliding it forward and backward to make sure it is lock in position. (cid:1) After adjusting the seatback, push back your body to make sure it is locked in position.

To stop the operation, push any driving position memory button. To reactivate the system, push the button “1” or “2” again. If is disconnected, the memory will be erased and the posi- tions will have to be set again.

the vehicle’s battery

CAUTION

(cid:1) Do not start the vehicle while the

adjustment are being made.

(cid:1) Take care not to select the wrong