2001 Toyota Sienna Owners Manual

01 SIENNA_U (L/O0008)

Power sliding door Some vehicles are equipped with a power sliding door. This system has the following functions: D The power sliding door can be oper- ated with the “DOOR L”, “DOOR R” and “POWER DOOR” switches inside the vehicle or “POWER DOOR”, “D− PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter. (For details about the wire- less transmitter, see “Wireless remote control” in this sec- tion.)

remote control

D If you move the sliding door

to the opening or closing direction by hand, the sliding door will automatically and completely open or close after you let go of the sliding door.

CAUTION

Do not leave small children or pets unattended in your vehicle. They could operate the power sliding door, and they themselves or others could be injured. Turn off the power sliding door system when the power sliding door is not in use.

or

“POWER DOOR”,

When the power sliding door system is on, you can open and close the sliding door with the “DOOR L”, “DOOR R” and “POWER DOOR” switches inside the ve- hicle “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless transmitter even if the sliding door child−protector is locked. If small children or pets are in the vehicle, turn off the system to prevent the accidental operation of the door.

remote control

the power sliding door,

“PWR DOOR OFF” SWITCH This switch is used to turn on and off the power sliding door system. For op- erating the “PWR DOOR OFF” switch on the instru- ment panel must be pushed out. (The orange line on the top of the switch indicates that the system is on.) To dis- able the power sliding door feature, push in the switch.

CAUTION

When jacking up the vehicle, turn off the power sliding door system and close the sliding door completely.

NOTICE

When your vehicle goes through an automatic car wash, make sure the power sliding door system is off.

2001 MY SIENNA (OM45406U)

19

01 SIENNA_U (L/O0008)

“DOOR L”, “DOOR R” AND “POWER DOOR” SWITCHES These switches are used to open and close the power sliding door. Push and release one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches. Opening and closing can be performed by the “PWR DOOR” switches under the following con- ditions: D The sliding door is unlocked. D The power sliding door system is on. is

“PWR DOOR OFF” switch

“DOOR R” and

“DOOR L”,

(The pushed out.)

Instrument panel

D To open the power sliding door when the ignition key is in the “ON” position, the transmission selector lever must be in “P”. (To close the sliding door from the fully−opened or half−opened posi- tion, the transmission selector lever is not required to be in “P”.)

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.

Center pillar

20

2001 MY SIENNA (OM45406U)

CAUTION

If you shift the automatic transmis- sion selector lever out of “P” and accelerate before the power sliding door is closed completely, the sliding door may reverse to the open posi- tion. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you start driving.

OPENING BY HAND When the power sliding door system is on, if you pull the outside door handle or push the inside lock release button to re- lease the sliding door, it will then automat- ically and completely open. When the power sliding door system is off, open the sliding door as usual. CLOSING BY HAND When the power sliding door system is on, if you slide the door about 10 cm (4
in.) to the closing direction and let the door go, it will automatically and com- pletely close. When the power sliding door system is off, close the sliding door as usual.

01 SIENNA_U (L/O0008)

“DOOR R” and inside

If you forcibly close the power sliding door by hand when the ignition key is in the “ON” position, the open power sliding door warning light may stay on. In this case, try opening and closing the power sliding door again by hand slowly, or use one of the “DOOR L”, “PWR DOOR” switches the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter. If you shift out of “P” when the power sliding door is opened or in the process of closing with the power sliding door sys- tem on, a buzzer will sound and the open power sliding door warning light will flash. This is a warning that the sliding door is not completely closed.

the

JAM PROTECTION FUNCTION If anything with sufficient resistance ob- structs the power sliding door while it is closing or opening, the sliding door will automatically reverse to the opposite di- rection. However, if the power sliding door is between fully−closed and half− opened positions while it is opening, the door will stop at that position. Before operating the power sliding door, make sure there is nobody near the slid- ing door. Make sure the sliding door stops at the fully−opened position, and then al- low the passengers to get on and off the vehicle.

2001 MY SIENNA (OM45406U)

21

DOOR

POWER

OPEN SLIDING WARNING LIGHT AND BUZZER This light on the instrument panel comes on if the power sliding door is not com- pletely closed with the ignition key in the “ON” position. (See “Service reminder indi- cators and warning buzzers” in Section 1−5.)

01 SIENNA_U (L/O0008)

The resistance must be as strong as the force of the moving door, or stronger. As the sliding door approaches fully− closed or fully−opened position, its moving force increases significantly. If the sliding door receives a strong im- pact, this function may work even if noth- ing is caught.

the

CAUTION

Power sliding door could injure people if they are caught in the door path. When using the power sliding door, observe the following: D Never try jamming any part of your jam protection

body to make the function work intentionally.

D You must always make sure

the heads, hands and other parts of the bodies of all occupants are away from the sliding door. If someone’s neck, head or hand gets caught in a closing sliding door, it could re- sult in a serious injury. When any- one closes the power sliding door, make sure he/she operates the slid- ing door safely.

NOTICE

Objects caught in the path of the slid- ing door may be damaged. Make sure there is nothing in the doorway be- fore closing the sliding door.

D The

jam protection

function may not work if something gets caught just before the sliding door is fully closed.

22

2001 MY SIENNA (OM45406U)

CAUTION

When the vehicle is stopped on a downward slope of a steep grade (17% or more), the sliding door may not stay in the fully−opened position and could suddenly close by itself, possibly resulting a personal injury. Making sure the sliding door does not close abruptly, the power sliding door system. Then the sliding door will operate under the control of the electric power.

turn on

THE POWER SLIDING

RESETTING DOOR SYSTEM If the power sliding door system operates incorrectly or does not operate under the following conditions, the system must be initialized and reset by the steps in the next column. D The battery is disconnected and then reconnected, or a discharged battery is recharged. In system by doing from 6 to 10.

initialize and reset the following steps

this case,

the

D The open power sliding door warning light stays on though the sliding door is closed. In system by doing from 1 to 10.

initialize and reset the following steps

this case,

the

CAUTION

To initialize and reset power sliding door system, stop the vehicle on a level ground.

01 SIENNA_U (L/O0008)

If the power sliding door system does not operate properly after the above proce- dure, there may be a problem in the sys- tem. Contact your Toyota dealer.

1. Be sure to turn off the power sliding door system by pushing in the “PWR DOOR OFF” switch.

2. Disconnect

the battery

for 1 minute

and then reconnect it.

3. Close the sliding door by hand.

(Step 3 can be performed before step 2.)

4. Turn on the power sliding door system by pushing out the “PWR DOOR OFF” switch.

5. Wait 5 seconds. 6. Open the sliding door by using one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches.

7. Wait 3 seconds after the sliding door

stops at the fully−opened position.

8. Close the sliding door by using one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches inside the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wire- less remote control transmitter.

9. Wait 3 seconds after the sliding door

stops at the fully−closed position.

10. Repeat the steps from 6 to 9.

2001 MY SIENNA (OM45406U)

23

01 SIENNA_U (L/O0008)

Wireless remote control

Locking operation

Unlocking operation

24

to

THE

AND

UNLOCKING

The wireless remote control system al- lows you lock or unlock all the doors from a distance within approxi- mately 1 m (3 ft.) of the vehicle. On some models, the system also allows you to activate the theft deterrent sys- tem from the same distance. LOCKING DOORS To lock and unlock all the doors, push the switches of the transmitter slowly and securely. To lock: Push the “LOCK” switch. All the doors are locked simultaneously. At this time one beep will be heard, parking lights, side marker lights, tail lights and other exterior lights will flash once. Left and right side power sliding door models—If is kept pressed in, the panic mode will work. (For details, see “PANIC (LOCK)” SWITCH.) Check to see that the doors are securely locked. If any of the doors is not securely closed, in the ignition switch, or locking cannot be performed by the “LOCK” switch and a beep will sound con- tinuously for 10 seconds. However, if the key is in the ignition, a beep will not sound.

“LOCK” switch

the key

the

is

if

2001 MY SIENNA (OM45406U)

the to unlock only

To stop the beep, close all the doors se- curely or push the “UNLOCK” switch. “UNLOCK” switch To unlock: Push once the driver’s door. Pushing the switch twice within 3 seconds unlocks all the doors simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights, side marker lights and tail lights will flash twice. When the “UNLOCK” switch is pressed, the personal lights, interior lights and/or ignition key light come on. The lights re- mains on for about 15 seconds unless any of the doors are opened then and closed. “Personal (For lights”, “Ignition switch light” in Section 1−4.) You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the doors will automatically lock again. If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera- tion is not repeated. Release the button and then push again.

information, see

lights” and/or

“Interior

further

SWITCHING BEEP SOUND ON AND OFF You can switch the beep on and off. (The beep is on initially and after battery re- placement.) To switch the beep on and off: With the driver’s door opened— 1. Insert the ignition key and remove it. 2. Within 5 seconds,

ignition key again and turn it to the “ON” posi- tion.

insert

the

3. After 10 seconds, push

the same “LOCK”, “UNLOCK” or “PANIC” button twice within 10 seconds. Two beep sounds inform you that the program has been switched on or off. If this procedure is not followed exactly, the beep will not operate as expected. Check the beep ON/OFF operation by pushing the wireless remote control trans- mitter switch after you finish this proce- dure. the beep does not operate as expected, repeat this procedure from step 1.

If

01 SIENNA_U (L/O0008)

the switch. The sliding

“POWER DOOR”, “D−PWR DOOR” AND “P−PWR DOOR” SWITCHES (on some models) This switch of the wireless remote con- trol transmitter is used to open and close the power sliding door. Push the switch slowly and securely. To open: Push door opens completely. To close: Push the switch again. The slid- ing door closes completely. Opening and closing can be performed by the “D−PWR DOOR” and “P−PWR DOOR” switches under the following conditions only: D The sliding door is unlocked. D The power sliding door system is on. is

“PWR DOOR OFF” switch

“POWER DOOR”,

(The pushed out.)

Right side only power sliding door mod- els

D The

ignition key

is not

in

the “ON”

position.

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.

Left and right side power sliding door models

2001 MY SIENNA (OM45406U)

25

01 SIENNA_U (L/O0008)

The alarm will last for one minute. To stop alarm midway, do the following: D Push any of the switch on the wireless

remote control transmitter.

D Lock or unlock either front doors or

back door with the key.

D Turn the ignition key from the “LOCK”

to “ON” position.

The panic mode does not work when the ignition key is in the “ON” position.

the

and holding

“PANIC (LOCK)” SWITCH (left and right side power sliding door models) Pushing “PANIC (LOCK)” switch blows the horn intermit- tently and flashes the headlights, tail lights and other exterior lights. The “PANIC (LOCK)” switch is used to deter vehicle theft when you witness any- one attempting to break into or damage your vehicle.

26

2001 MY SIENNA (OM45406U)

intermittently and

“PANIC” SWITCH (right side only power sliding door models) Pushing the “PANIC” switch blows the horn the headlights, tail lights and other exterior lights. The “PANIC” switch is used to deter ve- hicle theft when you witness anyone at- tempting into or damage your vehicle.

to break

flashes

01 SIENNA_U (L/O0008)

MODEL/FCC ID: GQ43VT14T CAN: 1470102849
MADE IN U.S.A. This complies with Part 15 of the FCC rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.

for

transmitters

You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information. If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: D Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.

D The battery may have been consumed. Check the battery in the transmitter. To replace the battery, see “REPLACING TRANSMITTER BATTERY”.

If you lose your wireless remote control transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” in Section 4.)

The alarm will last for one minute. To stop alarm midway, do the following: D Push any of the switch on the wireless

remote control transmitter.

D Lock or unlock either front doors or

back door with the key.

D Turn the key from the “LOCK” to “ON”

position.

REMOTE

CONTROL

The panic mode does not work when the key is in the “ON” position. WIRELESS TRANSMITTER The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause to damage remote control transmitter. D Do not leave the wireless remote con- trol the temperature becomes high such as on the dashboard.

transmitter on places where

the wireless

D Do not disassemble it. D Avoid knocking

it hard against other

objects or dropping it.

D Avoid putting it in water.

2001 MY SIENNA (OM45406U)

27

01 SIENNA_U (L/O0008)

REPLACING TRANSMITTER BATTERY For replacement, use a CR2032 lithium battery or equivalent.

CAUTION

Special care should be that small children do not swallow the re- moved transmitter battery or compo- nents.

taken

NOTICE

When replacing the transmitter bat- tery, be careful not to lose the com- ponents.

Replace the transmitter battery by the fol- lowing procedures:

1. Using a coin or equivalent, open the

2. Remove the discharged transmitter bat-

transmitter case.

tery.

NOTICE

Do not bend the terminals.

28

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

replacing battery, check

After the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.

that

Power windows

The windows can be operated with the switch on each front door. The power windows work when the ignition switch is in the “ON” position. OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Lightly pull up the switch.

2001 MY SIENNA (OM45406U)

29

3. Put a new transmitter battery with posi-

tive (+) side up.

Close the transmitter case securely.

NOTICE

z Make sure

the positive side and negative side of the transmitter bat- tery should be faced correctly.

z Be careful not to bend the electrode of the transmitter battery insertion and that dust or oils do not adhere to the transmitter case.

z Close the transmitter case securely.

01 SIENNA_U (L/O0008)

Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. It stops working when either front door is opened.

CAUTION

D Never try jamming any part of your jam protection

body to make the function work intentionally.

Window lock switch

D The

jam protection

function may not work if something gets caught just before fully closed.

the window

is

Automatic operation: Push the switch completely down or pull it completely up, and then release it. The window will fully open or close. To stop the window part- way, lightly move the switch in the oppo- site direction and then release it. Jam protection function: During automat- ic closing operation, the window stops and opens half way if something gets caught between the window and window frame. If the window receives a strong impact, this function may work even if nothing is caught.

THE

that controls

PASSENGER’S

the switch on

OPERATING WINDOW Use the passenger’s door. The driver’s door also has the switch the passenger’s window. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passenger’s window cannot be operated.

30

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

CAUTION

To avoid serious personal injury, you must do the following. D Always make sure the heads, hands and other parts of the bodies of all occupants are kept completely in- side the vehicle before you close the power windows. If someone’s neck, head or hands gets caught in a closing window, it could result in a serious injury. When anyone closes the power windows, make sure that he/she operates the win- dows safely.

D When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.

them

D Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power window switches and get in a window. Unat- tended children can be involved in serious accidents.

trapped

Power rear quarter windows

The rear quarter windows can be oper- ated with the “REAR VENT” switch on the instrument panel. rear quarter windows work The power when the ignition switch is in the “ON” position. Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either is opened. Both the left and the right rear quarter windows move as long as you hold the switch.

front door

2001 MY SIENNA (OM45406U)

31

01 SIENNA_U (L/O0008)

Center side windows and manual rear quarter windows

D Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power rear quarter window switch and get trapped in a window. Unattended children can be involved in serious accidents.

To open the window, pull the latch han- dle toward you and swing it fully out. When closing the window, make sure it is completely closed.

To open: Push the switch on the upper side. To close: Push the switch on the lower side.

CAUTION

To avoid serious personal injury, you must do the following. D Always make sure the hands and other parts of the bodies of all oc- cupants are kept completely inside the vehicle before you close the power If someone’s hands get caught in a closing window, it could result in a serious injury. When anyone closes the power rear quarter windows, make sure that he/she operates the windows safely.

rear quarter windows.

D When small children are in the ve- hicle, never let them use the power rear quarter window switches with- out supervision.

32

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

Back door

Insert the key into the keyhole and turn it. To lock: Turn the key clockwise. To unlock: Turn the key counterclockwise. To open the back door, pull the lever. Vehicles with power door lock system—All the doors lock and unlock simultaneously with back door.

Strap

Handle

When closing the back door, use the inside strap or handle for easier reach to the back door. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See in Section 2 for precautions in loading lug- gage.

“Luggage stowage precautions”

CAUTION

Keep the back door closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.

NOTICE

To prevent damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.

2001 MY SIENNA (OM45406U)

33

01 SIENNA_U (L/O0008)

Hood

To open the hood: 1. Pull the hood lock release lever. The

hood will spring up slightly.

CAUTION

Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.

2. In front of the vehicle, pull up the the

lever and

lift

auxiliary catch hood.

3. Hold the hood open by inserting the

support rod into the slot.

Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood make sure it If necessary, press down gently on the front edge to lock it.

the support rod

into place.

locks

to

CAUTION

After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.

34

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

Theft deterrent system

To deter the vehicle theft, the system is designed to give an alarm if any of the front, sliding or back doors or hood is forcibly unlocked or the battery ter- minal is disconnected and then recon- nected when the vehicle is locked. The alarm blows the horn intermittently and flashes the headlights, tail lights and other exterior lights.

As the doors are locked, the system will give you a preparation time of 30 seconds before the setting, during which the front, sliding or back doors and hood may be opened. Be careful not to unlock any door with the key or wireless remote control transmitter during setting. This will cancel the system. light 4. After making sure starts flashing, you may leave the ve- hicle.

indicator

the

The system will automatically be set after the preparation time passes. The indicator light will flash to show the system is set. If any of the front, sliding or back doors or hood is open at that time, the setting is interrupted until it is closed and locked. Never leave anyone in the vehicle when you set the system, because unlocking from the inside will activate the system.

SETTING THE SYSTEM 1. Turn

the ignition key position and remove it.

to the “LOCK”

is

removed

The indicator light will start flashing when the key ignition switch. (See “Engine immobiliser system” for details.) 2. Have all passengers get out of

from

the

the

vehicle.

3. Close the front, sliding and back doors and hood. Then lock all the doors with the key or wireless remote control transmitter.

The indicator light will come on when the front, sliding and back doors and hood are closed and locked.

2001 MY SIENNA (OM45406U)

35

01 SIENNA_U (L/O0008)

the system does not work properly,

If have it checked by your Toyota dealer.

described

The alarm will activate again under the same circumstances in “Activating the system”. Stopping the alarm To stop alarm midway, do the following: D Unlock either front door or back door with the key or wireless remote control transmitter.

WHEN THE SYSTEM IS SET Activating the system The system will give the alarm under the following conditions: D If any of

front, sliding or back doors the hood is forcibly opened without the key or wire- less remote control transmitter

is unlocked or

the

if

D If the battery terminal is disconnected

D Turn the key from the “LOCK” to “ON”

and then reconnected

position.

The indicator light will come on when the system is activating. If any of the doors is unlocked without the key or wireless remote control transmitter and the key is not in the ignition switch, all the doors will be automatically locked again. After 1 minute, the alarm will automatically stop and the indicator light will start flash- ing again. Reactivating the alarm Once set, the system cannot be cancelled without the key or wireless remote control transmitter. If the front, sliding and back doors and hood are closed after the alarm stops, the system automatically resets the alarm.

the system at

the

These ways cancel same time. TESTING THE SYSTEM 1. Open all the windows. 2. Set

the system as described above. The doors should be locked with the key or wireless remote control transmit- ter. Be sure to wait until the indicator light goes off or starts flashing.

3. Unlock any door from the inside. The

system should activate the alarm.

this operation

4. Cancel the system as described above. 5. Repeat the other doors and hood. When testing on the hood, also check that the system is activated when the battery terminal is disconnected and then reconnected.

for

36

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

Fuel tank cap

This indicates that the fuel filler door is on the left side of your vehicle.

With tachometer

Without tachometer

1. To open the fuel filler door, pull the

lever up. When refueling, turn off the engine.

CAUTION

D Do not smoke, cause sparks or al- flames when refueling.

low open The fumes are flammable.

D When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck is suddenly re- moved.

the cap

if

2001 MY SIENNA (OM45406U)

37

NOTICE

the

filler door Avoid opening when the left side sliding door is fully opened. Otherwise, the fuel filler door may be damaged.

fuel

01 SIENNA_U (L/O0008)

The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. The left side sliding door does not open fully if the fuel filler door is opened. Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.

CAUTION

D Make sure the cap is tightened se- in

curely to prevent fuel spillage case of an accident.

D Use only a genuine Toyota fuel tank cap for replacement. It is designed to regulate fuel tank pressure.

2. To remove the fuel tank cap, turn the cap slowly counterclockwise, then pause slightly before removing it. After removing the cap, hang it on the cap hanger.

the cap clockwise

It is not unusual to hear a slight swoosh when the cap is opened. When installing, turn till you hear a click. If the cap is not tightened securely, the malfunction lamp comes on. Make sure the cap is tightened securely.

indicator

38

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

Electric moon roof

Sliding operation

Tilting operation

Tilting operation— To tilt up: Push the switch on the “TILT UP” side. To lower: Push the switch on the “SLIDE OPEN” side. You may stop the moon roof at any de- sired position. The roof will move while the switch is being pushed and stop when released except to slide open.

CAUTION

To avoid serious personal injury, you must do the following. D While the vehicle is moving, always keep the heads, hands and other parts of the bodies of all occupants away from the roof opening. Other- wise, they could be seriously in- jured if the vehicle stops suddenly or if the vehicle is involved in an accident.

the

To operate the moon roof, use switches beside the personal light. The moon roof works when the ignition switch is in the “ON” position. Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. It stops working when any of the doors is opened. Sun shade operation— The sun shade can be opened or closed by hand. Sliding operation— To open: Push the switch on the “SLIDE OPEN” side. The roof will fully open. To stop the roof partway, push the “SLIDE OPEN” or “TILT UP” side briefly. The sun shade will be opened together with the roof. To close: Push the switch on the “TILT UP” side. As a precaution when closing, the roof stops at the half closed position before fully closing. Therefore, release the switch and then push it again to close it com- pletely.

the switch on either

2001 MY SIENNA (OM45406U)

39

01 SIENNA_U (L/O0008)

D Always make sure nobody places his/her head, hands and other parts of the body in the roof opening be- fore you close the roof. If some- one’s neck, head or hands gets caught in the closing roof, it could result injury. When anyone closes the roof, first make sure it is safe to do so.

in a serious

D Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the moon roof switches and get trapped in the roof opening. Unat- tended children can be involved in serious accidents.

D Never sit on

top of

the vehicle

around the roof opening.

40

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

SECTION 1− 3

OPERATION OF INSTRUMENTS AND CONTROLS Seats, Seat belts, Steering wheel and Mirrors Seats Front seats Rear seats Head restraints Armrests Seat heaters Seat belts SRS driver and front passenger airbags SRS side airbags Child restraint Tilt steering wheel Outside rear view mirrors Anti−glare inside rear view mirror Auto anti−glare inside rear view mirror Sun visors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42
42
45
61
62
62
63
74
81
87
114
115
116
117
118

2001 MY SIENNA (OM45406U)

41

01 SIENNA_U (L/O0008)

Seats While the vehicle is being driven, all ve- hicle occupants should have the seatback upright, sit well back in the seat and prop- erly wear the seat belts provided.

CAUTION

D Do not drive the vehicle unless the occupants are properly seated. Do top of a not allow sitting on folded−down seatback, or the luggage compartment. Persons not properly seated and/or properly re- strained by seat belts can be se- verely injured in the event of emer- gency braking or a collision.

in

D During driving, do not allow pas- to stand up or move sengers around between seats. Severe inju- ries can occur in the event of emer- gency braking or a collision.

Front seats— —Front seat precautions (on vehicles with SRS side airbags)

CAUTION

The SRS side airbags are installed in the driver and front passenger seats. Observe the following precautions. D Do not lean against the front door when the vehicle is in use. The side airbag inflates with considerable speed and force; you may be killed or seriously injured.

for

D Do not use accessories

the seats which cover the parts where the side airbags inflate. Such acces- sories may prevent the side airbags from activating correctly, causing death or serious injury.

the

D Do not modify or replace the seats or upholstery of front seats with the side airbags. Such changes may disable the system or cause the side airbags to inflate acciden- tally, resulting in death or serious injury. Consult your Toyota dealer if you this kind.

insist modifications of

—Seat adjustment precautions Adjust the driver’s seat so that the foot pedals, steering wheel and instrument panel controls are within easy reach of the driver.

CAUTION

D Adjustments should not be made while the vehicle is moving, as the seat may unexpectedly move and cause the driver to lose control of the vehicle.

D When adjusting the seat, be careful not to hit the seat against a pas- senger or luggage.

D After adjusting the seat position, try sliding it forward and backward to make sure it is locked in posi- tion.

D After adjusting the seatback, exert body pressure to make sure it is locked in position.

42

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

—Adjusting front seats (manual seat)

D While adjusting the seat, do not put your hands under the seat or near the moving parts. You may catch and injure your hands or fingers.

1. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. 2. SEATBACK

ADJUSTING

ANGLE

LEVER

lever up. lean back to the desired angle

Lean forward and pull the Then and release the lever.

CAUTION

To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maxi- mum protection in a frontal or rear collision when the driver and the pas- senger are sitting up straight and well back If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen. Therefore, in the event of a frontal collision, the risk of personal injury may increase with increasing recline of the seat- back.

in the seats.

2001 MY SIENNA (OM45406U)

43

01 SIENNA_U (L/O0008)

1. SEAT POSITION AND SEAT CUSHION

HEIGHT ADJUSTING SWITCH

Move the control switch in the desired direction. Releasing the switch will stop the seat at that position. Do not place anything under front seats. It might interfere with the seat−lock mechanism. 2. SEATBACK

ADJUSTING

ANGLE

the

SWITCH

Move the control switch in the desired direction. Releasing the switch will stop the seat- back at that position.

—Adjusting front seats (power seat)

3. SEAT CUSHION HEIGHT ADJUSTING

KNOB

Turn the knob either way.

44

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

Rear seats— —Rear seat precautions

CAUTION

CAUTION

To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maxi- mum protection in a frontal or rear collision when the driver and the pas- senger are sitting up straight and well back If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen. Therefore, in the event of a formal collision, the risk of personal injury may increase with increasing recline of the seat- back.

in the seats.

D Any operations should not be made

while the vehicle is moving.

D When adjusting the seat, be careful not to hit the seat against a pas- senger or luggage.

D Third seats only: Adjust both seats to the same position and seatbacks to the same angle when a person sits on the third seat center posi- tion. Otherwise, the person can not wear seat belt properly and this may cause serious injuries in a col- lision.

D After adjusting the seat position, try sliding it forward and backward to make sure it is lock in position. D After adjusting the seatback, exert body pressure to make sure it is locked in position.

D When returning seats to their origi-

nal position: Make sure the seat belts are not twisted or caught under the seat and are arranged in their proper position and are ready to use. is securely Make sure locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion. Failure to do so will prevent seat belt from operating properly.

the seat

Folding the seats up will enlarge the lug- gage compartment. See “Luggage stowage precautions” in Section 2 for precautions in loading luggage.

2001 MY SIENNA (OM45406U)

45

01 SIENNA_U (L/O0008)

—Adjusting second seat (bench seat)

—Adjusting second seats (captain seat)

SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever up. lean back to the desired angle Then and release the lever.

CAUTION

To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maxi- mum protection in a frontal or rear collision when the passengers are sit- ting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdo- men. Therefore, the event of a frontal collision, the risk of personal injury may increasing recline of the seatback.

increase with

in

46

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

—Moving second seat for third seat entry (right side captain seat)

CAUTION

D After putting back

try pushing the seat forward and rear- ward to make sure it is secured in place.

the seat,

D Passengers sitting in the third seat must be careful not to accidentally pull the release lever while the ve- hicle is moving.

For access to the third seat, do this. 1. Pull the lever behind the seatback.

The seat will slide forward.

2. Move the seat to the front−most posi-

tion.

After passengers are in, lift up the seat- back and return the seat until it locks.

2001 MY SIENNA (OM45406U)

47

1. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. Do not place anything under the seats. It might interfere with the seat−lock mecha- nism. 2. SEATBACK

ADJUSTING

ANGLE

LEVER

lever up. lean back to the desired angle

Lean forward and pull the Then and release the lever.

CAUTION

To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maxi- mum protection in a frontal or rear collision when the passengers are sit- ting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdo- men. Therefore, the event of a frontal collision, the risk of personal injury may increasing recline of the seatback.

increase with

in

01 SIENNA_U (L/O0008)

—Folding second seat (bench seat)

CAUTION

To avoid serious injury: D Do not set up the seatback table

while the vehicle is moving.

D Do not sit on the folded seatback. D Make sure the second seat is se- curely locked in position when you set the second seat as a temporary table.

NOTICE

To prevent the seat from damaging, avoid putting heavy loads on the tem- porary table.

Lift the seatback angle adjusting lever (1) or press the lever (2) behind the seatback and fold the seatback down.

You can use the second seatback as a temporary table only when the vehicle is stopped.

48

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

—Folding second seats (captain seat)

1. Pull the lever behind the seatback. Right side only—The seat will slide for- ward.

2. Lift the seatback angle adjusting le-

ver and fold the seatback down.

You can use the second seatback as a temporary table only when the vehicle is stopped.

2001 MY SIENNA (OM45406U)

49

01 SIENNA_U (L/O0008)

—Removing second seat (bench seat)

CAUTION

To avoid serious injury: D Do not set up the seatback table

while the vehicle is moving.

D Do not sit on the folded seatback. D Make sure the second seat is se- curely in sliding position when you set the second seat as a temporary table.

locked

D When the second seat for a table was slid for accessing to the third seat, get the seatback up to the upright position, fold the seatback down again, and make certain all the latches are engaged.

NOTICE

To prevent the seat from damaging, avoid putting heavy loads on the tem- porary table.

1. Lift the seatback angle adjusting le- ver (1) or press the lever (2) behind the seatback and fold the seatback down.

2. Pull the seat lock release lever. Lift the seat and remove the seat toward you.

Removing the second seat will enlarge the luggage compartment. See “Luggage stow- age precautions” in Section 2 for precau- tions in loading luggage.

50

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

CAUTION

reinstalling

When removing or the seat, observe the following to prevent personal injury: D Be careful not to get your hands or

feet pinched in the seat.

D Be careful not to hit the removed seat against a person or drop it on yourself.

NOTICE

Avoid putting heavy loads on the re- moved seat. The metallic tips of the seat legs may be damaged and the seat cannot be reinstalled.

To reinstall the second seat, do this. 1. Hook the front legs to the floor. 2. Lock the rear legs.

CAUTION

D Make sure

the seat

is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion. Failure to do so will prevent seat belt from operating properly.

D Do not remove the second seat or fold the seatback down whenever the third seat is folded up.

2001 MY SIENNA (OM45406U)

51

01 SIENNA_U (L/O0008)

—Removing second seats (captain seat)

1. Pull the lever behind the seatback. Right side only—The seat will slide for- ward.

2. Lift the seatback angle adjusting le-

ver and fold the seatback down.

3. Pull the seat lock release lever. Lift the

the seat cushion and remove seat toward you.

Removing the second seat will enlarge the luggage compartment. See “Luggage stow- age precautions” in Section 2 for precau- tions in loading luggage.

52

2001 MY SIENNA (OM45406U)

01 SIENNA_U (L/O0008)

CAUTION

reinstalling

When removing or the seat, observe the following to prevent personal injury: D Be careful not to get your hands or

feet pinched in the seat.

D Be careful not to hit the removed seat against a person or drop it on yourself.

NOTICE

Avoid putting heavy loads on the re- moved seat. The metallic tips of the seat legs may be damaged and the seat cannot be reinstalled.

To reinstall the second seat, do this. 1. Hook the front legs to the floor. 2. Lock the rear legs.

CAUTION

D Make sure

the seat

is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion. Failure to do so will prevent seat belt from operating properly.

D Do not remove the second seat or fold the seatback down whenever the third seat is folded up.

2001 MY SIENNA (OM45406U)

53

01 SIENNA_U (L/O0008)

—Adjusting third seats

1. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. When a person sits on the third seat center position, adjust both seats to the same position. Do not place anything under the seats. It might interfere with the seat−lock mecha- nism. 2. SEATBACK

ADJUSTING

ANGLE

LEVER

lever up. lean back to the desired angle

Lean forward and pull the Then and release the lever. When a person sits on the third seat center position, adjust both seatbacks to the same angle.

54

2001 MY SIENNA (OM45406U)

CAUTION

to

D Adjust both seats to the same posi- tion and seatbacks the same angle when a person sits on the third seat center position. Other- wise, the person can not wear seat belt properly and this may cause serious injuries in a collision.

D To reduce the risk of sliding under lap belt during a collision, the the seatback any avoid reclining more than needed. The seat belts provide maximum protection in a frontal or rear collision when the passengers are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly the abdomen. Therefore, in the event of a frontal collision, the risk of personal injury may increase with increasing recline of the seatback.

to

01 SIENNA_U (L/O0008)

—Folding third seats

third center seat belt as

the

BEFORE FOLDING THIRD SEAT Stow shown in the illustration. This prevents when you fold up the third seat.

the belt

from

falling out

NOTICE

z The third center seat belt must be stowed before you fold up the third seat.

z Make sure to stow the third center seat belt in order not to cause dam- age on the seat belt by pinching it between the third seat inner leg and seat striker.

FOLDING UP THIRD SEAT 1. Remove the head restraint.

2001 MY SIENNA (OM45406U)

55

01 SIENNA_U (L/O0008)

2. Slide the seat to the rear−most posi-

tion.

3. Lift the seatback angle adjusting le- ver (1) or press the lever (2) behind the seatback and fold the seatback down.

56

2001 MY SIENNA (OM45406U)

You can use the third seatback as a tem- porary is stopped.

table only when

the vehicle

CAUTION

To avoid serious injury: D Do not set up the seatback table

while the vehicle is moving.

D Do not sit on the folded seatback. D Make sure the third seat is securely locked in position when you set the third seat as a temporary table.

01 SIENNA_U (L/O0008)

NOTICE

To prevent the seat from damaging,