2013 Toyota Prius Owners Manual

2-1. Driving procedures

NOTICE

■When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle: ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ●Brake function ●Changes in quantity and quality of engine oil, transmission fluid for the

hybrid system, etc.

●Lubricant condition for the bearings and suspension joints (where possi-

ble), and the function of all joints, bearings, etc.

If the P position control system is damaged by flooding, it may not be possi- ble to shift the shift position to P, or from P to other positions. When the shift position cannot be changed from P to any other position, the front wheels will lock, and you will be unable to tow the vehicle with the front wheels on the ground, as the front wheels may be locked. In this case, transport the vehicle with both front wheels or all four wheels lifted.

193

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures Power (ignition) switch

Performing the following operations when carrying the electronic key on your person starts the hybrid system or changes “POWER” switch modes. ■ Starting the hybrid system

STEP 1

STEP 2

Check that the parking brake is set. Firmly depress the brake pedal. Check that the “POWER” switch indicator turns green. If the indi- cator does not turn green, the hybrid system cannot be started. When the shift position is N, the hybrid system cannot start. Shift the shift position to P when starting the hybrid system. (→P. 207)

STEP 3

Press the “POWER” switch.

The hybrid system can be started from any “POWER” switch mode. Continue depressing the brake pedal until the hybrid system is completely started.

194

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

STEP 4

Check that the “READY” indicator is on. If the “READY” indicator changes from a flashing light to a solid light and the buzzer sounds, the hybrid system is starting nor- mally. The vehicle will not move when the “READY” indicator is off. The vehicle can move when the “READY” indicator is on even if the engine is stopped. (The gasoline engine starts or stops auto- matically in accordance with the state of the vehicle.)

■ Stopping the hybrid system

STEP 1

STEP 2

Stop the vehicle completely. Set the parking brake. (→P. 214)

STEP 3

Shift the shift position to P. (→P. 207)

Check that the shift position indicator shows P. (→P. 204)

STEP 4

STEP 5

Press the “POWER” switch. The hybrid system will stop. Slowly release the brake pedal and check that the indicator on the “POWER” switch is off.

195

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

■ Changing “POWER” switch modes Modes can be changed by pressing the “POWER” switch with the brake pedal released. (The mode changes each time the switch is pressed.)

Off The emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “POWER” switch indicator turns amber. ON mode All electrical components can be used. The “POWER” switch indicator turns amber.

196

PRIUS_OM_OM47791U_(U)

2

2-1. Driving procedures

■Auto power off function

If the vehicle is left in ACCESSORY mode for more than 20 minutes or ON mode (the hybrid system is not operating) for more than an hour with the shift position in P, the “POWER” switch will automatically turn off. However, this function cannot entirely prevent the 12-volt battery from discharging. Do not leave the vehicle with the “POWER” switch in ACCESSORY or ON mode for long periods of time when the hybrid system is not operating.

■Sounds and vibrations specific to a hybrid vehicle

→P. 36

■Electronic key battery depletion

→P. 78

■When the ambient temperature is low, such as during winter driving

conditions The “READY” indicator may flash for a long time when the hybrid system is starting. Driving will become possible once the “READY” indicator has illumi- nated. Wait until the “READY” indicator has illuminated.

■Conditions affecting operation

→P. 74

■Notes for the entry function

→P. 75

■If the hybrid system does not start

The immobilizer system may not have been deactivated. (→P. 138) Contact your Toyota dealer.

197

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

■When the “POWER” switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.

■If the “READY” indicator does not come on

If the “READY” indicator does not come on when you press the “POWER” switch with the shift position in P and the brake pedal depressed, contact your Toyota dealer immediately.

■If the hybrid system is malfunctioning

→P. 501

■If the electronic key battery is depleted

→P. 460

■Operation of the “POWER” switch

●When operating the “POWER” switch, one short, firm press is enough. If the switch is pressed improperly, the hybrid system may not start or the “POWER” switch mode may not change. It is not necessary to press and hold the switch.

●If attempting to restart the hybrid system immediately after turning the “POWER” switch off, the hybrid system may not start in some cases. After turning the “POWER” switch off, please wait a few seconds before restarting the hybrid system.

■Automatically P position selection function

→P. 209

198

PRIUS_OM_OM47791U_(U)

2

2-1. Driving procedures

■When the P position control system malfunctions

The “POWER” switch will not be able to be turned off. In such a case, the switch can be turned off after applying the parking brake. Have the vehicle inspected by your Toyota dealer immediately.

■Ending display

When the “POWER” switch is turned off, each of the following will be dis- played on the multi-information display, and will extinguish after approxi- mately 30 seconds. ●The driving distance, driving time, consumption and eco savings since

the hybrid system was started*

●The odometer ●The clock *: The amount of money saved or spent, selected on the Eco savings record

display (→P. 56), is displayed.

CAUTION

■When starting the hybrid system

Always start the hybrid system while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the hybrid system under any cir- cumstances. Doing so may cause an accident resulting in death or serious injury.

■Stopping the hybrid system in an emergency

If you want to stop the hybrid system in an emergency while driving the vehi- cle, press and hold the “POWER” switch for more than 2 seconds, or press it briefly 3 times or more in succession. (→P. 563) However, do not touch the “POWER” switch while driving except in an emer- gency. Turning the hybrid system off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.

199

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

NOTICE

■To prevent 12-volt battery discharge

●Do not leave the “POWER” switch in ACCESSORY or ON mode for long

periods of time without the hybrid system on.

●If the hybrid system is off, but the indicator on the “POWER” switch is illu- minated, this indicates that the “POWER” switch is still turned on. When exiting the vehicle, always check that the “POWER” switch is off. ■Symptoms indicating a malfunction with the “POWER” switch

If the “POWER” switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction. Con- tact your Toyota dealer immediately.

200

PRIUS_OM_OM47791U_(U)

2

2-1. Driving procedures EV drive mode

In EV drive mode, the electric motor (traction motor), powered by the hybrid battery (traction battery), is used to drive the vehicle. This mode allows you to drive in residential areas late at night, or in indoor parking lots etc. without concern for noises and exhaust gas emissions.

Turns EV drive mode on/off

When EV drive mode is turned on, the EV drive mode indica- tor will come on. Pressing the switch when in EV drive mode will return the vehicle to normal driving (using the gasoline engine and elec- tric motor [traction motor]).

201

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

■Situations in which EV drive mode cannot be turned on It may not be possible to turn EV drive mode on in the following situations.* If it cannot be turned on, a buzzer will sound and a message will be shown on the multi-information display. ●The temperature of the hybrid system is high.

The vehicle has been left in the sun, driven on a hill, driven at high speeds, etc.

●The temperature of the hybrid system is low.

The vehicle has been left in temperatures lower than about 32 °F (0 °C) for a long period of time etc.

●The gasoline engine is warming up. ●The hybrid battery (traction battery) is low.

When the amount of remaining hybrid battery (traction battery) charge displayed on the meter is low. (→P. 44)

●Vehicle speed is high. ●The accelerator pedal is depressed firmly or the vehicle is on a hill etc. ●The windshield defogger is in use. *: Depending on the circumstances, EV drive mode may also not be

switched to in situations other than those above.

■Switching to EV drive mode when the gasoline engine is cold

If the hybrid system is started while the gasoline engine is cold, the gasoline engine will start automatically after a short period of time in order to warm up. In this case, you will become unable to switch to EV drive mode. After the hybrid system has started and the “READY” indicator has illumi- nated, press the EV drive mode switch before the gasoline engine starts to switch to EV drive mode.

202

PRIUS_OM_OM47791U_(U)

2

2-1. Driving procedures

■Automatic cancelation of EV drive mode

When driving in EV drive mode, the gasoline engine may automatically restart in the following situations. When EV drive mode is canceled, a buzzer will sound and the EV drive mode indicator will flash and go off. ●The hybrid battery (traction battery) becomes low. ●Vehicle speed becomes high. ●The accelerator pedal is depressed firmly or the vehicle is on a hill etc.

■Possible driving distance when driving in EV drive mode

In EV drive mode, it is possible to drive up to about 1.3 mile (2 km) if driving at a speed of about 25 mph (40 km/h) or less. (The distance that is possible depends on the hybrid battery [traction battery] level and driving conditions.)

■Changing a driving mode when in EV drive mode

EV drive mode can be used in conjunction with Eco drive mode and power mode. However, EV drive mode may be automatically canceled when used in con- junction with power mode.

■Fuel economy

PRIUS is designed to achieve the best possible fuel economy during normal driving (using the gasoline engine and electric motor [traction motor]). Driv- ing in EV drive mode more than necessary may lower fuel economy.

CAUTION

■While driving

When driving in EV drive mode, pay special attention to the area around the vehicle. Because there is no engine noise, pedestrians, people riding bicy- cles or other people and vehicles in the area may not be aware of the vehicle starting off or approaching them, so take extra care while driving.

203

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures Hybrid transmission

Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever

Shift lever Operate the shift lever gently and ensure correct shifting operation.

When shifting to the D or R positions, move the shift lever along the shift gate. To shift to the N position, slide the shift lever to the left and hold it. The shift position will change to N. Shifting to B is only possible when shift position D is selected.

The shift lever will always return to this original position after a shifting operation.

When shifting from P to N, D or R, from D to R, or from R to D, ensure that the brake pedal is being depressed and the vehicle is stationary.

204

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

Shift position indicator The position of the frame on the shift position indicator changes in accordance with the current shift position. When any shift position other than D or B is selected, the arrow toward B and B position indicator disappear from the shift position indicator.

When selecting the shift position, make sure that the shift position has been changed to the desired position by checking the shift position indica- tor provided on the instrument cluster. ■ Shift position purpose

Shift position

Function

Parking the vehicle/starting the hybrid system

Reversing Neutral

Normal driving*

Applying moderate engine braking when driving

down hills or on steep slopes

*: For good fuel economy and noise reduction, the D position should usu-

ally be used.

205

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

■ Selecting a driving mode

The following modes can be selected to suit driving conditions:

Eco drive mode Suitable for improving the fuel economy, because the torque cor- responding to the accelerator pedal depression amount can be generated more smoothly than it is in normal conditions and the operation of the air conditioning system (heating/cooling) will be minimized. When the “ECO MODE” switch is pressed, the “ECO MODE” indicator comes on. Power mode Use when high levels of response and feeling are desirable, such as when driving in mountainous regions or when overtak- ing. When the power mode switch is pressed, the power mode indicator comes on.

206

PRIUS_OM_OM47791U_(U)

2

2-1. Driving procedures

P position switch

■ When shifting the shift position to P

Fully stop the vehicle and set the parking brake, and then press the P position switch.

the shift position

When is changed to P, the indicator comes on. Check that the P position is illumi- nated on the shift position indica- tor.

■ Shifting the shift position from P to other positions

● While depressing the brake pedal firmly, operate the shift lever. If the shift lever is operated without depressing the brake pedal, the buzzer will sound and the shifting operation will be disabled. ● When selecting the shift position, make sure that the shift posi- tion has been changed to the desired position by checking the shift position indicator provided on the instrument cluster. ● The shift position cannot be changed from P to B directly.

207

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

■Operation of the air conditioning system in Eco drive mode

Eco drive mode controls the heating/cooling operations and fan speed of the air conditioning system to enhance fuel efficiency. (→P. 206) To improve air conditioning performance, adjust the fan speed or turn off Eco drive mode.

■For the shift positions

●When the “POWER” switch is off, the shift position cannot be changed. ●When the “POWER” switch is in ON mode (the hybrid system is not oper- ating), the shift position can only be changed to N. The shift position will be changed to N even if the shift lever is shifted to D or R and held in that position.

●When the “READY” indicator is on, the shift position can be changed

from P to D, N or R.

●When the “READY” indicator is flashing, the shift position cannot be changed from P to other position even if the shift lever is operated. Wait until the “READY” indicator changes from a flashing to a solid light, and then operate the shift lever again.

●The shift position can only be changed to B directly from D. In addition, if an attempt is made to change the shift position by moving the shift lever or by pressing the P position switch in any of the following situa- tions, the buzzer will sound and the shifting operation will be disabled or the shift position will automatically change to N. When this happens, select an appropriate shift position. ●Situations where the shifting operation will be disabled:

• When an attempt is made to change the shift position from P to other

position by moving the shift lever without depressing the brake pedal.

• When an attempt is made to change the shift position from P or N to B

by moving the shift lever.

208

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

●Situations where the shift position will automatically change to N: • When the P position switch is pressed while the vehicle is running.*1
• When an attempt is made to select the R position by moving the shift lever when the vehicle is moving forward.*2
• When an attempt is made to select the D position by moving the shift lever when the vehicle is moving in reverse.*3
• When an attempt is made to change the shift position from R to B by

*1: Shift position may be changed to P when driving at extremely low

moving the shift lever.

speeds.

*2: Shift position may be changed to R when driving at low speeds. *3: Shift position may be changed to D when driving at low speeds.

■Reverse warning buzzer

When shifting into R, a buzzer will sound to inform the driver that the shift position is in R.

■Automatically P position selection function

When the shift position is in a position other than P, pressing the “POWER” switch with the vehicle stopped completely will cause the shift position to change to P automatically, and then the “POWER” switch will turn off.

■If the shift position cannot be shifted from P

There is a possibility that the 12-volt battery is discharged. Check the 12-volt battery in this situation. (→P. 550)

209

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

■About engine braking

When shift position B is selected, releasing the accelerator pedal will apply engine braking. ●When the vehicle is driven at high speeds, compared to ordinary gaso- line-fueled vehicles, the engine braking deceleration is felt less than that of other vehicles.

●The vehicle can be accelerated even when shift position B is selected. If the vehicle is driven continuously in the B position, fuel efficiency will become low. Usually, shift the shift position to D.

■When driving with cruise control or radar cruise control activated

Even if switching the driving mode to power mode with the intent of enabling engine braking, engine braking will not activate because cruise control or radar cruise control will not be canceled.

■When canceling Eco drive mode/power mode

●Press the switch again. Also, power mode will be canceled automatically when the “POWER” switch is turned off. However, Eco drive mode will not be canceled automatically until the switch is pressed, even if the “POWER” switch is turned off.

●When in Eco drive mode, if the power mode switch is pressed or the operation is reversed, the mode will switch to that of the last switch to be pressed.

■Switching the drive mode when in EV drive mode

→P. 203

■After recharging/reconnecting the 12-volt battery

→P. 439

210

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

■Customization

Settings (e.g. Reverse warning buzzer) can be changed. (Customizable features →P. 596)

CAUTION

■When driving on slippery road surfaces

Do not accelerate or shift the shift position suddenly. Sudden changes in engine braking may cause the vehicle to spin or skid, resulting in an accident.

■For the shift lever

Do not remove the shift lever knob or use anything but a genuine Toyota shift lever knob. Also, do not hang anything on the shift lever. Doing so could prevent the shift lever from returning to position, causing unexpected accidents to occur when the vehicle is in motion.

■P position switch

Do not press the P position switch while the vehicle is moving. If the P position switch is pressed when driving at very low speeds (for example, directly before stopping the vehicle), the vehicle may stop sud- denly when the shift position switches to P, which could lead to an accident.

211

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures

NOTICE

■Hybrid battery (traction battery) charge

If the shift position is in N, the hybrid battery (traction battery) will not be charged. To help prevent the battery from discharging, avoid leaving the N position selected for an extended period of time.

■Situations where P position control system malfunctions are possible If any of the following situations occurs, P position control system malfunc- tions are possible. Immediately stop the vehicle in a safe place on level ground, apply the park- ing brake, and then contact your Toyota dealer. ●When the “P LOCK MALFUNCTION” warning message appears on the

multi-information display. (→P. 515)

●When the shift position indicator remains off.

■Notes regarding shift lever and P position switch operation

Avoid repeatedly operating the shift lever and P position switch in quick suc- cession. The system protection function may activate and it will not be temporarily possible to shift the shift position other than P. If this happens, please wait for a while before attempting to change the shift position again.

212

PRIUS_OM_OM47791U_(U)

2

2-1. Driving procedures Turn signal lever

The turn signal lever can be used to show the following intention of the driver:

Right turn Left turn Lane change to the right (push and hold the lever partway) The right hand signals will flash until you release the lever. Lane change left (push and hold the lever partway) The left hand signals will flash until you release the lever.

the

to

■Turn signals can be operated when The “POWER” switch is in ON mode.

■If the indicator flashes faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

213

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures Parking brake

U.S.A.

Canada

To set the parking brake, fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. (Depressing the pedal again releases the parking brake.)

■Parking brake engaged warning buzzer

→P. 499

■Usage in winter time

→P. 321

NOTICE

■Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

214

PRIUS_OM_OM47791U_(U)

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 119)

215

PRIUS_OM_OM47791U_(U)

2-2.Instrument cluster Gauges and meters

The units used on the display may differ depending on the target region. The following gauges and meters and display illuminate when the “POWER” switch is in ON mode:

Fuel gauge Displays the quantity of fuel remaining in the tank. Speedometer Displays the vehicle speed. Instantaneous fuel consumption Displays the current rate of fuel consumption. Shift position indicators Displays the shift position. Multi-information display Presents the driver with a variety of driving-related data. (→P. 225)

216

PRIUS_OM_OM47791U_(U)

2

Touch tracer display (if equipped)

2-2. Instrument cluster

When the audio control switches, climate control switches, “DISP” button or “TRIP” button of the steering wheel are touched, the touch tracer display will appear in front of the gauges, with the touched button highlighted to allow the driver to identify the button that is being operated.

The button can then be operated by further presses. If an audio/navigation system is used that is not compatible with the steering switches in this vehi- cle, the audio switch display may not operate correctly.

217

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

MPH or km/h button

The speed units can be selected MPH or km/h.

Press the button to switch the display between MPH and km/h.

218

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

Instrument panel light control

The brightness of the instrument panel lights can be adjusted by turn- ing the dial.

Brighter Darker

■Brightness of the instrument panel light

If the headlight switch is turned on while the surrounding area is dark, the instrument panel lights will dim.

219

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

CAUTION

■To prevent an accident

Instrument cluster

Do not place anything or attach a sticker in front of the instrument cluster. The item may obscure or obstruct the display, or could reflect off the display, possibly causing an accident.

NOTICE

■To prevent damage to the engine and its components

The engine may be overheating if the high coolant temperature warning light comes on or flashes. In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 556)

220

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and instrument panel inform the driver of the status of the vehicle’s vari- ous systems. For the purpose of explanation, the following illustration displays all indicators and warning lights illuminated. Instrument cluster

Some indicators and the units used on the display may differ depending on the target region. Instrument panel

221

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

(U.S.A.)

(Canada)

Turn signal indicator (→P. 213)

Headlight indicator (→P. 252)

Tail light indicator (→P. 252)

Headlight high beam indicator (→P. 255)

Front fog light indicator (→P. 258)

Security indicator (→P. 138)

“READY” indicator (→P. 194)

Eco Driving Indicator Light (→P. 226)

“ECO MODE” indicator (→P. 206)

Power mode indicator (→P. 206)

Cruise control indicator (→P. 268, 272)

Radar cruise control indicator (→P. 272)

“SET” indicator (→P. 268, 272)

LKA (Lane-Keeping Assist) indicator (→P. 289)

Slip indicator (→P. 301, 305)

EV indicator (→P. 226)

(if equipped)

(if equipped)

(if equipped)

(if equipped) *1, 2

222

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

EV drive mode indica- tor (→P. 201)

*1, 3

(if equipped)

“PCS” warning (→P. 308)

Shift position indicators (→P. 204)

“AIR BAG ON/OFF” indicator (→P. 156)

*1: These lights turn on when the “POWER” switch is turned to the ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is on, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

*2: The light flashes to indicate that the system is operating. *3: The light comes on when the system is turned off. The light flashes

faster than usual to indicate that the system is operating.

223

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 499)

*1

*2

*1

*1

*1

*1

*1

*1

*1

*1

*1

(U.S.A.) *1

(Canada) *1

(U.S.A.) *1

(Canada) (red) *1, 2

(yellow) *1

(if equipped) *2

(U.S.A.)

(Canada)

(if equipped)

(if equipped)

*1

(if equipped) *2

(if equipped) *1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is on, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

*2: The light flashes to indicate a malfunction.

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS and SRS airbag warning light not come on when you start the hybrid system, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

224

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster Multi-information display

The multi-information display presents the driver with a variety of driving-related data, including the clock.

● Energy monitor (→P. 44) ● Hybrid System Indicator (→P. 226) ● 5-minute/1-minute fuel consumption (→P. 52) ● Monthly fuel consumption record/eco savings record (→P. 55) ● Odometer/trip meter/distance to empty (→P. 230) ● Clock (→P. 232) ● Calendar (→P. 232) ● Dynamic radar cruise control display (if equipped) (→P. 272) ● LKA (Lane-Keeping Assist) display (if equipped) (→P. 289) ● Warning messages (→P. 513)

225

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

Switching the display

To switch “DISP” button.

the display, press

On vehicles with touch tracer dis- play, the steering switches opera- tion status is displayed on the instrument cluster for confirma- tion purposes. (→P. 217)

the odometer,

To switch trip meter and distance to empty, press “TRIP” button.

Hybrid System Indicator

Hybrid System Indicator displays the hybrid system operating condi- tion and provides Eco-friendly driving assistance in accordance with the driving conditions and the acceleration.

226

PRIUS_OM_OM47791U_(U)

2

2-2. Instrument cluster

■ Names and meaning of each icons

Hybrid battery (traction bat- tery) status (→P. 50) EV indicator The EV indicator comes on when driving the vehicle using only the electric motor (traction motor). Eco Driving Indicator Light Turns on when the vehicle is driven in Eco-friendly. Hybrid System Indicator Refer to “Reading Hybrid System Indicator” below. Average speed* Average fuel consumption/eco savings* Use the displayed average fuel consumption as a reference.

*:The current amount since the trip meter was reset will be displayed. These functions can be reset by pressing and holding the “TRIP” button. The display can be switched between average fuel consump- tion/average speed and eco sav- ings. (→P. 234)

227

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Reading Hybrid System Indicator

Charge area Eco area Power area Hybrid Eco area

As shown below, the driving conditions of the vehicle can be con- firmed by checking the status of the indicator bar.

228

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

Hybrid System Indicator*1

Charge area: Shows regenerative charging. (→P. 34)

Hybrid Eco area: Shows that gasoline engine power is not being used very often.*2

Eco area: Shows that the vehicle is driven in Eco-friendly.

Power area: Shows that the driving power is more than the upper limit of Eco driving (during full power driving etc.).

*1: The images are examples only, and may vary slightly from actual condi-

tions.

*2: The gasoline engine will automatically stop and restart under various

conditions.

229

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

Odometer/trip meter/distance to empty

■ Switching the display

The display changes as follows each time the “TRIP” button is pressed. Also, if the button is kept pressed down while the trip meter is being displayed, the trip meter will be reset to 0.

230

PRIUS_OM_OM47791U_(U)

2

2-2. Instrument cluster

■ Display items ● Odometer

● Trip meter

Displays the total distance the vehicle has been driven.

Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different dis- tances independently.

● Distance to empty

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.

• When only a small amount of fuel is added to the

tank, the display may not be updated. When refueling, turn the “POWER” switch off. If the vehicle is refueled without turning the “POWER” switch off, the display may not be updated.

231

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

Clock

The clock can be adjusted by pressing the buttons.

Adjusts the hours. Adjusts the minutes. Rounds to the nearest hour.* *: e.g. 1:00 to 1:29 → 1:00
1:30 to 1:59 → 2:00

Setting up the displays

STEP 1

Press the “DISP” button until the “SETTINGS” screen appears.

Calendar will be displayed.

STEP 2

While the vehicle is stopped, press and hold the “DISP” button until the screen changes. The selected item will change each time the “DISP” button is pressed.

232

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Setting the gasoline price

STEP 1

Select “GASOLINE PRICE”.

Press and hold the “DISP” button to enter the setting mode.

STEP 2

Select gasoline price by pressing the “DISP” or “TRIP” button.

Press and hold the button to change the amount continuously. If neither button is operated for approximately 5 seconds, the set- ting will be changed and the screen will return to the previous display.

233

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Switching the fuel consumption display

STEP 1

STEP 2

Select “FUEL CONSU. DISP.”.

Press and hold the “DISP” button to enter the setting mode.

Select “CONSUMP.” or “ECO SAVINGS”.

Press and hold the “DISP” button to finish setting.

234

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Setting the comparison consumption Select TION”.

STEP 1

“COMP. CONSUMP-

Press and hold the “DISP” button to enter the setting mode.

STEP 2

Select the comparison consump- tion by pressing the “DISP” or “TRIP” button.

Press and hold the button to change the amount continuously. If neither button is operated for approximately 5 seconds, the set- ting will be changed and the screen will return to the previous display.

235

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Setting the calendar

STEP 1

STEP 2

Select “CALENDAR”.

Press and hold the “DISP” button to enter the setting mode.

Select the date by pressing the “DISP” or “TRIP” button.

Press and hold the button to change the date continuously. If neither button is operated for approximately 5 seconds, the set- ting will be changed and the screen will return to the previous display.

236

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Switching the EV indicator and Eco Driving Indicator Light

activated or deactivated

STEP 1

Select “EV/ECO”.

Press and hold the “DISP” button to enter the setting mode.

STEP 2

Select “ON” or “OFF”.

Press and hold the “DISP” button to finish setting.

237

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Switching the steering switch operation display on/off (if

equipped)

STEP 1

STEP 2

Select “STEERING SWITCH”.

Press and hold the “DISP” button to enter the setting mode.

Select “ON” or “OFF”.

Press and hold the “DISP” button to finish setting.

238

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Selecting 12h/24h clock display

STEP 1

Select “CLOCK”.

Press and hold the “DISP” button to enter the setting mode.

STEP 2

Select “12h” or “24h”.

Press and hold the “DISP” button to finish setting.

239

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Selecting the language

STEP 1

Select “LANGUAGE”.

Press and hold the “DISP” button to enter the setting mode.

STEP 2

Select the language you want to read.

Press and hold the “DISP” button to set the language.

240

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Turning off the multi-information display

STEP 1

Select “SCREEN OFF”.

Press and hold the “DISP” button to enter the setting mode.

STEP 2

Select “OFF”.

Press and hold the “DISP” button to turn off the multi-information display. To re-display the multi-information display, press the “DISP” button to display “SETTINGS” screen and follow the same pro- cedure, selecting “ON” instead of “OFF”.

the

■ Returning to the previous screen

Select “EXIT” and press and hold the “DISP” button.

The screen will revert to the “SETTINGS” screen.

241

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■System check display

After switching the “POWER” switch to ON mode, “welcome to PRIUS” is dis- played while is checked. When the system check is com- plete, the normal screen will return.

system operation

■Ending display

→P. 199

■Eco Driving Indicator Light

Eco Driving Indicator Light will turn on when driving power is lower than the upper limit of Eco driving. It will turn off when the acceleration exceeds the Eco driving accelerator upper limit or when the vehicle is stopped. Eco Driving Indicator Light will not operate in the following conditions: ●The shift position is anything other than D. ●The driving mode is set to power mode or EV drive mode. (→P. 201, 206) ●The vehicle speed is approximately 80 mph (130 km/h) or higher. Eco Driving Indicator Light is also displayed when 5-minute consumption, 1- minute consumption, monthly fuel consumption record or eco savings record is displayed. Eco Driving Indicator Light can be set to activated or deactivated. (→P. 237)

242

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■Driving in Eco drive mode

The multi-information display will automatically switch the display to Hybrid System Indicator, regardless of which display is currently being shown. (→P. 226)

■Touch tracer display (if equipped)

●The touch tracer display can be set to not display even if the steering

switches are touched.

●Only the circular, rubber-covered switches have a built-in touch sensor. Touching any of the other switches will not display the touch tracer dis- play.

■Display settings can be changed when

The vehicle speed is less than approximately 5 mph (8 km/h).

■Engine speed

On hybrid vehicles, engine speed is precisely controlled in order to help improve fuel efficiency and reduce exhaust emissions etc. There are times when the engine speed that is displayed may differ even when vehicle oper- ation and driving conditions are the same.

■When the 12-volt battery is disconnected

The following data will be reset. ●Average fuel consumption ●Distance to empty ●Average vehicle speed ●Clock ●Display settings ●Trip meter

243

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■Vacuum fluorescent display

Small spots or light spots may appear on the display. This phenomenon is characteristic of vacuum fluorescent displays, and there is no problem to continue using the display.

NOTICE

■Steering switches

To prevent damage to the steering switches, observe the following precau- tions. ●Do not touch the steering switches with wet hands ●Do not push hard or sharp objects into the steering switches ●Do not subject the steering switches to strong impacts ●Do not allow organic solvents containing thinner, benzene or gasoline, or

acidic/alkaline soap to adhere to the surfaces of the steering switches

244

PRIUS_OM_OM47791U_(U)

2

2-2. Instrument cluster Head-up display∗

The head-up display can be used to project vehicle speed and other information onto the windshield.

(Head-up display)

Head-up display Display brightness will change automatically according to the brightness of the surrounding area. HUD main switch Turn-by-turn switch (if equipped) Display position adjustment switch Display brightness adjust- ment switch Used the display brightness to the desired level.

navigation

to adjust

∗: If equipped 245

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■ Head-up display contents

● Speedometer

Displays the vehicle speed. ● Hybrid System Indicator

Provides assistance for Eco-friendly driving.

● Turn-by-turn navigation*

Displays a notification of upcoming intersections during navigation system route guidance. (→P. 249) ● Dynamic radar cruise control*

Displays the approach warning. (→P. 272)

● PCS (Pre-Collision System)*

Indicates that there is a possibility of collision. (→P. 307)

● LKA (Lane-Keeping Assist)*

Displays a warning message that alerts the driver of a deviation from the lane through use of the lane departure warning function. (→P. 504) *: If equipped

246

PRIUS_OM_OM47791U_(U)

2

2-2. Instrument cluster

Switching the head-up display

Display items can be switched by pressing the “HUD” main switch.

Speedometer Displays the vehicle speed. Speedometer and Hybrid Sys- tem Indicator Displays Hybrid System Indicator under the speedometer. (→P. 226) Off When on, the indicator light on the “HUD” main switch comes on.

Switching the turn-by-turn navigation display (if equipped)

On/off

When on, the indicator light on the “NAVI” button comes on.

247

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

Setting up the display

■ Setting the brightness

The brightness of the display is automatically adjusted in accor- dance with the brightness of the surrounding environment. How- ever, the brightness can also be manually adjusted in 5 stages.

Darker Brighter The brightness can be manually adjusted in 5 stages.

■ Adjusting the display position

Lower Higher

248

PRIUS_OM_OM47791U_(U)

2

2-2. Instrument cluster

Turn-by-turn navigation display (if equipped)

the direction

When the vehicle approaches an intersection, the vehicle should go is guided by the arrow. When the vehicle approaches an intersection, the route guidance will start and the distance* to the intersection will also be dis- played. *: The distance decreases in incre- ments of 50 ft. (15 m) and the dis- tance indication will disappear when the vehicle passes through the intersection.

■System check display

When the “POWER” switch is turned OFF while the head-up display is on, and is then turned again to ON mode, “welcome to PRIUS” is displayed while system operation is checked. When the system check is complete, the normal screen will return.

249

PRIUS_OM_OM47791U_(U)

2-2. Instrument cluster

■When driving on snowy roads or in other bright environments

When the highest level of brightness has been reached, the display can be made even brighter by pressing and holding “∧” on the brightness control button. Pressing “∨” on the brightness control button or turning the “POWER” switch off will cause the brightness level to revert to the original level.

■Display speed setting function

The speedometer can be set to display only when a desired vehicle speed is reached.

STEP 1

STEP 2

STEP 3

Press and hold the “HUD” main switch while the vehicle is stopped and while the head-up display is showing only the speedometer. The speedometer will begin to flash. Set the desired display speed on the speedometer by pressing “∧” and “∨” on the display position adjustment button. Press “∧” to raise the speed and “∨” to lower. The speed will change by 1 mph (1.6 km/h) each time the button is pressed, and continu- ously by 10 mph (16 km/h) when the button is pressed and held. Press and hold the “HUD” main switch to finish setting.

■Head-up display

The head-up display may seem dark and hard to see when viewed through sunglasses, especially polarized sunglasses. Adjust the brightness of the head-up display or remove your sunglasses.

■When the 12-volt battery is disconnected

The head-up display settings will be reset.

250

PRIUS_OM_OM47791U_(U)

2

2-2. Instrument cluster

CAUTION

■Before using the head-up display

Check that the position and brightness of the head-up display image does not interfere with safe driving. Incorrect adjustment of the image’s position or brightness may obstruct the driver’s view and lead to an accident, resulting in death or serious injury.

NOTICE

■To prevent damage to the components

If an object falls into the opening of the head-up display, remove it immediately. Also, avoid spilling water or other liquids near the head-up display opening as this may cause mechanical damage.

251

PRIUS_OM_OM47791U_(U)

2-3. Operating the lights and windshield wipers Headlight switch

The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: Type A

The headlights, park- ing lights and so on turn on and off auto- matically (when the “POWER” switch is in ON mode). The side marker, parking, tail, license plate and instrument panel lights turn on. The headlights and all the lights listed above turn on. The daytime running lights turn off.

252

PRIUS_OM_OM47791U_(U)

2

2-3. Operating the lights and windshield wipers

Type B

The daytime running lights turn on. The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all the lights listed above turn on. The daytime running lights turn off.

253

PRIUS_OM_OM47791U_(U)

2-3. Operating the lights and windshield wipers

Type C

The daytime running lights turn on. The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and