2004 Toyota Prius Owners Manual

oil. Then go immediately for emer- gency help.

Checking auxiliary battery condition— —Precautions

CAUTION

AUXILIARY BATTERY PRECAUTIONS When the auxiliary battery must be replaced, use the Prius designated battery. The auxiliary battery produces flam- mable and explosive hydrogen gas. D Do not cause a spark from the bat-

tery with tools.

D Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or

clothes.

D Never ingest electrolyte. D Wear protective safety glasses when

working near the battery.

D Keep children away from the bat-

tery.

298

Hold−down clamp

Ground cable

NOTICE

83p001c

Terminals

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

z Be sure the hybrid system and all accessories are off before perform- ing maintenance.

z When checking the battery, remove the ground cable from the negative terminal (“–” mark) first and rein- stall it last.

z Be careful not to cause a short cir-

cuit with tools.

z Take care no solution gets into the

battery when washing it.

If the auxiliary battery is disconnected or run down, the power window and back door may not operate automatically and the jam protection function will not func- tion correctly and does not open the back door after you reconnect, replace or re- charge the battery. In any of these cases, you should normalize each system. To normalize them, see “Power windows” on page 40 and “Back door” on page 39. Before you disconnect the auxiliary bat- tery, confirm the shift position is “P” and apply the parking brake completely.

is “N” when

After you reconnect the auxiliary battery, shift the shift lever to “N” and confirm the shift position the “IG−ON” mode is enabled. After connecting system may not start by pushing “POWER” switch. once again.

the hybrid the In that case, push it

the cables,

299

Auxiliary battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Make sure the power switch on the recharger is off when connecting the charger cables to the battery and when disconnecting them.

CAUTION

D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

D Only do a slow charge (3.5A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

300

Checking and replacing fuses

NOTICE

Type A

Never recharge the battery with the hybrid system on. Also, be sure all accessories are turned off.

Good

Blown

Type B

83p003

Good

Blown

Type C

Good

Blown

83p004b

locations” on page 275

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations of the fuses. Turn the hybrid system and inoperative component off. Pull the suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See page 314 for the functions controlled by each circuit.

for

Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “DOME” or “OBDII” fuse, which may be dispens- able for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close to the rating as possible. If the amperage is fuse might blow out again. but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

that specified,

lower

than

the

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

301

D Do not disassemble, repair or take apart the headlight bulbs, connec- tor, power supply circuits and ro- tate components. Or you may be injured by electric shocks. Call your dealer when the headlights fail to work or have to be replaced or dis- posed of.

NOTICE

Only use a bulb of the listed type.

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the hybrid system and light switch are off. Use bulbs with the wattage ratings given in the table.

CAUTION

D To prevent burning yourself, do not replace the light bulbs while they are hot.

D Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

Vehicles with discharge headlights— D Do not touch the high voltage sock- the headlight turns on. is momentarily generated injury by

et when 20000 V and may cause severe electric shock.

Adding washer fluid If any washer does not work, the wash- er tank may be empty. Add washer fluid. You may use plain water as washer fluid. However, in cold areas where tempera- tures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

302

the

fogging

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lense becomes wet in the rain or in a car wash. This is not a problem because the temperature difference between the outside and the windshield fogs up in the rain. However, if there large drop of water on the inside of the lense, or if there is water pooled light, contact your Toyota dealer.

is caused by

inside of

lense,

inside

is a

just

like

the

the

Light bulbs

Bulb No.

Type

9006

—

—

— —

Headlights Discharge headlights Halogen headlights Front fog lights Parking lights Front turn signal lights Rear turn signal lights — Tail lights — Back−up lights License plate lights Interior lights Personal lights Door courtesy lights Vanity lights L u g g a g e c o m p a r t- ment light

— — — — —

—

7440

35

60/55

51

21

21
21

A: D2R Discharge bulbs B: HB2 Halogen bulbs C: HB4 Halogen bulbs D: Wedge base bulbs E: Double end bulbs

303

—Headlights

83p030

83p031

83p010a

1. Open the hood. Remove the clips

and take out the cover.

Remove and install the clips as shown in the following illustration.

Removing clip

2. RIGHT−HAND HEADLIGHT ONLY: Re- move the clip and take out the air cleaner inlet.

Remove and install the clip as shown in the following illustration.

83p032

Installing clip

304

83p011

83p013a

83p014a

Removing clip

83p012

Installing clip

3. Unplug the connector. Turn the bulb cover counter−clockwise and remove it.

If the connector is tight, wiggle it.

4. Release

the bulb retaining spring and remove the bulb along with the socket. Install a new bulb into the socket and return the bulb retaining spring to its original position.

To install a bulb, align the tabs of the bulb with the cutout of the mounting hole.

305

—Front fog lights If either the left or right front fog lights burns out, contact your Toyota dealer.

NOTICE

Do not try to replace the front fog light bulbs by yourself. You may dam- age the vehicle.

—Parking lights

83p016a

83p015b

5. Install the bulb cover and turn clockwise. Plug in the connector.

it

306

83p017a

—Front turn signal lights

—Rear turn signal, tail and back−up lights

83p018a

83p023a

83p025c

83p019b

83p024b

a: Rear turn signal light b: Back−up light c: Tail light

307

—License plate lights

83p026b

83p028b

Remove the cover.

83p027a

308

SECTION 9

SPECIFICATIONS SPECIFICATIONS Dimensions and weight Electric motor Enginee Fuel Hybrid vehicle battery Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

310
310
310
311
311
311
313
314

309

Dimensions and weight Overall length mm (in.) 4445
1725
Overall width mm (in.) Overall height mm (in.) 1490
2700
mm (in.) Wheelbase 1505
mm (in.) Front tread Rear tread mm (in.) 1480
Vehicle capacity weight (occupants + luggage) kg (lb.)

385

*: Unladen vehicle

(175.0) (67.9) (58.7)* (106.3) (59.3) (58.3)

(845)

Electric motor Type:

Permanent magnet synchronous motor (water cooling)

Maximum output:

50/1200 − 1540 kW/rpm

Maximum torque:

400/0 − 1200 N·m/rpm

Engine Model: 1NZ−FXE Type: 4−cylinder in line, 4 cycle, gasoline Bore and stroke, mm (in.):

75.0 x 84.7 (2.95 x 3.33)

Displacement, cm3 (cu. in.):

1497 (91.4)

310

Fuel Fuel type:

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher

Fuel tank capacity, L (gal., lmp. gal.):

45 (11.9, 9.9)

Nickel−Metal hydride battery

Hybrid vehicle battery Type: Voltage: 7.2 V Capacity: 6.5 Ah (3HR) Quantity: 28
Overall voltage: 201.6 V

Service specifications ENGINE Valve clearance (engine cold), mm (in.):

Intake Exhaust

0.17—0.23 (0.007—0.009) 0.27—0.33 (0.011—0.013)

Spark plug type:

DENSO SK16R11
NGK IFR5A11

Spark plug gap, mm (in.):

1.1 (0.043)

311

ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., lmp. qt.):

Recommended oil viscosity: SAE 5W−30

With filter Without filter

3.7 (3.9, 3.3) 3.4 (3.6, 3.0)

“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade:

API grade SL “Energy−Conserving” or ILSAC multigrade engine oil.

oil008

Outside temperature

Please contact your Toyota dealer for further details.

COOLING SYSTEM Total capacity, L (qt., Imp. qt.):

For gasoline engine For electric motor and inverter and converter Coolant type:

8.6 (9.0, 7.5)

2.7 (2.9, 2.4)

“Toyota Super Long Life Coolant” is used in your Toyota vehicle at factory fill. In order to avoid technical prob- lems, only use “Toyota Super Long Life Coolant” or similar high quality ethyl- ene glycol based non−silicate, non− amine, non−nitrite, and non−borate coolant with long−life hybrid organic acid technology. (Coolant with long−life hybrid organic acid is a combination of low phosphates and or- ganic acids.) Do not use plain water alone. Please contact your Toyota dealer for further details.

technology

312

AUXILIARY BATTERY Open voltage at 20_C (68_F):

12.6 − 12.8 V 12.2 − 12.4 V 11.5 − 11.9 V

Fully charged Half charged Discharged

the

is removed with all

[Voltage that is checked 20 minutes after the key lights turned off] Charging rates: HYBRID TRANSAXLE Fluid capacity (drain and refill), L (qt., Imp. qt.): 3.6 (3.8, 3.2)

3.5 A max.

Fluid type:

“Toyota Genuine ATF WS” or equivalent

BRAKES Minimum pedal clearance when depressed with the force of 196 N (20 kgf, 44 lbf) with the traction motor running, mm (in.):

101.0 (3.98)

Pedal free play, mm (in.):

1 − 4 (0.04 − 0.16)

Parking brake adjustment when depressed with the force of 294 N (30 kgf, 66 lbf):

6 − 9 clicks

Fluid type:

SAE J1703 or FMVSS No. 116 DOT 3

STEERING Wheel free play:

Less than 30 mm (1.2 in.)

Tires Tire size and inflation pressure:

Tire size kPa (kgf/cm2 or bar, psi) Standard

Front P185/65R15 86S

240 (2.4, 35)

Rear P185/65R15 86S

230 (2.3, 33)

Spare

T125/70D16 96M

420 (4.2, 60)

15 x 6JJ 16 x 4T

torque, N·m

(kgf·m,

Wheel size: Standard Spare

Wheel nut ft·lbf):

103 (10.5, 76)

NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire inflation pres- sure” “Aluminum wheel precautions”, page 289 through 296.

through

313

Fuses

90p007b

90p005b

90p008b

Instrument panel

Engine compartment

Luggage compartment

1. PWR 30 A: Power windows 2. DEF 40 A: Rear window defogger 3. M/HTR 15 A: Outside rear view mirror

heater

4. WIP 30 A: Windshield wiper 5. RR WIP 15 A: Rear wiper 6. WSH 20 A: Washer 7. ECU−IG 7.5 A: Smart entry and start system, power windows, multi−informa- tion display, electric power steering, theft deterrent system

314

8. GAUGE 10 A: Gauge and meter, back− flasher, power

lights, emergency

up windows

9. OBD 7.5 A: On−board diagnosis sys-

tem

10. STOP 7.5 A: Stop lights 11. DOOR 25 A: Power door lock system 12. ACC−B 25 A: “POWER OUTLET”,

“ACC” fuses

13. ECU−B 15 A: Multi−information display, power windows, air conditioning system

15. TAIL 10 A: Tail lights, license plates

light, parking lights

16. PANEL 7.5 A: Multi−information dis- instrument

play, clock, audio system, panel lights

17. A/C (HTR) 10 A: Air conditioning sys-

tem

18. FR DOOR 20 A: Power windows 19. PWR OUTLET 15 A: Power outlet 20. ACC 7.5 A: Audio system, multi−infor-

mation display, clock

14. AM1 7.5 A: Hybrid system

21. PWR OUTLET FR 15 A: Power outlet

22. IGN 7.5 A: Hybrid system, hybrid ve- hicle immobilizer system, SRS airbags

23. SPARE 30 A: Spare 24. SPARE 15 A: Spare 25. DRL 7.5 A: Daytime running light sys-

tem

26. H−LP LO RH 15 A (Vehicles with dis- charged headlight) or 10 A (Vehicles with halogen headlight): Right−hand headlight (low beam)

27. H−LP LO LH 15 A (Vehicles with dis- charged headlight) or 10 A (Vehicles with halogen headlight): Left−hand headlight (low beam)

35. P CON MTR 30 A: Parking control system or ABS−1 25 A: Anti−lock brake system

36. ETCS 10 A: Electronic throttle control

system

37. BATT FAN 10 A: Battery cooling fan 38. HAZ 10 A: Turn signal lights, emergen-

cy flasher

39. DOME 15 A: Audio system,

interior lights, smart entry and start system, gauge and meter, lights, luggage room light, clock

turn signal

40. ABS MAIN3 15 A: Anti−lock brake sys-

tem

28. H−LP HI RH 10 A: Right−hand head-

41. ABS MAIN2 10 A: Anti−lock brake sys-

light (high beam)

tem

29. H−LP HI LH 10 A: Left−hand headlight

42. ABS MAIN1 10 A: Anti−lock brake sys-

(high beam)

tem

30. EFI 15 A: Multiport fuel injection sys- injection

tem/sequential multiport system

fuel

31. AM2 15 A: “IGN” fuse, ignition system 32. HORN 10 A: Horn 33. HEV 20 A: Hybrid system 34. P CON MAIN 7.5 A: Parking control system, hybrid vehicle immobilizer sys- tem

43. FR FOG 15 A: Fog lights 44. CHS W/P 10 A: CHS W/P 45. AMP 30 A: Audio system 46. PTC HTR2 30 A: PTC heater 47. PTC HTR1 30 A: PTC heater 48. CDS FAN 30 A: Electric cooling fan 49. DC/DS−S 5 A: Inverter and converter 50. MAIN 120 A: Hybrid system

315

316

SECTION 10

REPORTING SAFETY DEFECTS FOR U.S. OWNERS REPORTING SAFETY DEFECTS FOR U.S. OWNERS 318
Reporting safety defects for U.S. owners

. . . . . . . . . . . . . . . . . . . . . .

317

To contact NHTSA, you may either call the Auto Safety Hotline toll−free at 1−800−424−9393 (or 366−0123
in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

Reporting safety defects for U.S. owners If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the Na- tional Highway Traffic Safety Ad- ministration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., (Toll−free: Inc. 1−800−331−4331).

If NHTSA receives similar com- plaints, it may open an investiga- tion, and if it finds that a safety de- fect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual prob- lems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.

318

Quick index D If a service reminder indicator or warning buzzer comes on D If your vehicle will not start D If your vehicle overheats D If you have a flat tire D If your vehicle needs to be towed D Tips for driving during break-in period D How to start the hybrid system D General maintenance Gas station information Fuel type:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

117
238
242
243
254
202
230
269

UNLEADED gasoline, Octane Rating 87 (Research Octane Number 91) or higher. See page 202 for detailed information.

Fuel tank capacity:

45 L (11.9 gal., 9.9 lmp. gal.) See page 204 for detailed information.

Engine oil:

API grade SL “Energy−Conserving” or ILSAC multigrade engine oil is recommended. See page 283 for detailed information.

Tire information: See pages 289 through 296. Tire inflation pressure: See page 313.

U −5

Publication No. OM47482U Part No. 01999-47482
Printed in Japan 04−0407−01

U)

Important information about this manual

Safety and vehicle damage warnings

Safety symbol

Throughout this manual, you will see safety and vehicle dam- age warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows:

CAUTION

This is a warning against anything which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to reduce the risk of injury to yourself and others.

NOTICE

This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or re- duce the risk of damage to your vehicle and its equipment.

When you see the safety symbol shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.

Important information about your Toyota

Occupant restraint systems

Toyota encourages you and your family to take the time to read Section 2−2 of this Owner’s Manual carefully. In terms of helping you understand how you can receive the maximum benefit of the occupant restraint systems this vehicle provides, Section 2−2 of this Owner’s Manu- al is the most important section for you and your family to read. Section 2−2 describes the function and operation con- cerning seats, seat belts, SRS airbags and child re- straint systems of this vehicle and some potential haz- ards you should be aware of. These systems work to- gether along with the overall structure of this vehicle in order to provide occupant restraint in the event of a crash. The effect of each system is enhanced when it is used properly and together with other systems. No single occupant restraint system can, by itself, provide you or your family with the equal level of restraint which these systems can provide when used together. That is why it is important for you and your family to under- stand these systems and how they relate to each other.

the purpose and proper use of each of

ii

The purpose of all occupant restraint systems is to help reduce the possibility of death or serious injury in the event of a collision. None of these systems, either indi- vidually or together, can ensure that there is no injury in the event of collision. However, the more you know about these systems and how to use them properly, the greater your chances become of surviving an accident without death or serious injury.

Seat belts provide the primary restraint to all occupants of the vehicle, and every occupant of the vehicle should wear seat belts properly at all times. Children should always be secured in child restraint systems that are appropriate for their age and size. SRS (Supplemental imply, Restraint System) airbags are, as designed to, seat belts and are not substitutes for them. SRS airbags can be very effective in reducing the risk of head and chest injuries by preventing contact of the head and chest with interior portions of the vehicle.

to work with, and be supplemental

their names

tremendous speed. The rapid deployment of

In order to be effective, the SRS airbags must deploy with the SRS airbags makes the SRS airbags themselves poten- tial sources of serious injury if an occupant is too close to an airbag, or if an object or some part of his or her body has been placed between the occupant and the airbag at the time of deployment. This is just one exam- ple of how the instructions in Section 2−2 of this Own- er’s Manual will help ensure proper use of the occupant restraint systems, and increase the safety they can pro- vide to you and your family in the event of an accident.

Toyota recommends you to read the provisions in Sec- tion 2−2 carefully and refer to them as needed during your time of ownership of this vehicle.

New vehicle warranty

Your new vehicle limited warranties:

is covered by

the

following Toyota

D New vehicle warranty D Emission control systems warranty D Others For the “Owner’s Warranty Information Booklet” or “Owner’s Manual Sup- plement”.

information, please

further

refer

to

Your responsibility for maintenance

It is the owner’s responsibility to make sure the speci- fied maintenance is performed. Section 7 gives details of these maintenance requirements. Also included in Sec- tion 7 is general maintenance. For scheduled mainte- nance information, please refer to the “Scheduled Main- tenance Guide” or “Owner’s Manual Supplement”.

iii

Accessories, spare parts and modification of your Toyota

for Toyota vehicles are currently available

A wide variety of non−genuine spare parts and accesso- ries in the market. You should know that Toyota does not warrant these products and is not responsible for their perfor- mance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.

This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durabili- ty, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.

Important health and safety information about your Toyota

CAUTION

D WARNING: Engine exhaust, some of its constitu- ents, and a wide variety of automobile compo- nents contain or emit chemicals known to the State of California to cause cancer and birth de- fects and other reproductive harm. In addition, oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other repro- ductive harm.

lead and

D Battery posts, terminals and related accessories contain lead compounds. Wash your hands after handling. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing thoroughly with soap and water.

iv

Spark ignition system of your Toyota

Tires and loading on your Toyota

Underinflated or overinflated tire inflation pressure and the excess load may result in the deterioration of steering ability and braking ability, leading to an accident. Check the tire inflation pressure periodi- cally and be sure to keep the load limits given in this Owner’s Manual. For details about tire inflation pressure and load limits, see page 289 and pages 224.

The spark ignition system in your Toyota meets all re- quirements of the Canadian Interference−Causing Equip- ment Standard.

Installation of a mobile two−way radio system

As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as multiport fuel injection system / sequential multiport fuel injection system, cruise control system, anti−lock brake system, vehicle stability control system, SRS airbag sys- tem, seat belt pretensioner system and Toyota hybrid system, be sure to check with your Toyota dealer for precautionary measures or special instructions regarding installation.

Hybrid vehicle battery

The hybrid vehicle battery has a limited service life. Call your Toyota dealer information about recycling or disposal of hybrid vehicle battery and your vehicle.

for

Scrapping of your Toyota

in The SRS airbag and seat belt pretensioner devices your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt preten- sioner removed and disposed of by the qualified service shop or by your Toyota dealer before you dispose of your vehicle.

CAUTION

When your vehicle or battery needs to be dis- posed of, be sure to consult your Toyota dealer. Hybrid vehicle batteries must be collected through Toyota dealers. If your vehicle is dis- posed of without dismantling, someone could receive an electric shock by touching the high voltage parts of the hybrid vehicle battery. If the battery is not disposed of properly, its contents can cause death or serious injury.

vi

CAUTION

Precautions for use

of hybrid vehicle

The vehicle has both high voltage DC and AC systems as well as a 12−volt system. DC and AC high voltage are both very dangerous and can cause death or serious injury, se- vere burns and electric shock. D In order to avoid personal injuries, do not touch the high voltage cables (orange colored) and their connectors.

D Follow the caution labels attached to the high volt-

age parts.

D Do not remove or replace the high voltage parts such as the inverter unit (located in the engine compartment), hybrid vehicle battery (located be- hind rear seat), etc.

D Do not touch the service plug located in the left side trim of the luggage compartment without hy- brid system technical training. (See “Precautions for use” on page 12 in Section 1−2.) This compo- nent is provided to disable the high voltage sys- tem in case of servicing at a Toyota dealer.

CAUTION

If an accident occurs

D Pull your vehicle off the road, push the “P” posi- tion switch, stop the hybrid system and if the key is inserted into key slot, remove it.

D In order to avoid personal injuries, do not touch any high voltage wirings and their connectors, and high voltage parts (inverter unit, hybrid vehicle battery, etc.).

D If some exposed electric wires are protruding in- side or outside of your vehicle, an electric shock may occur. Never touch the electric wires.

touch

it because

D If fluid leaks or gets in some parts of the vehicle, never it may be electrolyte (strong alkali) from the hybrid vehicle battery. If it gets into your skin or eyes, wash off immediately with a large amount of water, if possible, boric acid solution, and get immediate medical attention in order to help avoid serious injury.

D If a vehicle fire occurs, extinguish it using a fire extinguisher for the exclusive use on electric fires. Or, use a large amount of water to prevent flam- mable gas from being generated from the batteries.

vii

D If your vehicle needs to be towed, do it with the front wheels raised. For details on towing, see “If your vehicle needs to be towed” on page 254 in Section 5.

CAUTION

High Voltage

Your vehicle is equipped with cables connected to parts of the vehicle subject to high voltage (about 500 V at maximum). There are some other parts that reach high temperatures while you drive. Never touch battery cables (wrapped in orange−colored har- nesses) or their connectors since they are under high voltage and dangerous. Caution labels are ap- plied to these parts to identify them. Carefully ob- serve the instructions on these caution labels.

00p001

viii

ix

Information Guide

How to operate PUSH BUTTON STARTING HYBRID SYSTEM

A. Starting HYBRID SYSTEM

(1) (2)

(3)

Apply the parking brake firmly. Insert the key* and press the “POWER” switch with the brake pedal depressed firmly. You can start driving your Prius when the flashing “READY” light stays on after a few seconds and you hear a beep.

B. Stopping HYBRID SYSTEM

Press the “POWER” switch with the vehicle at a stop.

C. Selecting “ACC” or “IG-ON” mode

“OFF”

“ACC”

Green

“IG-ON”

Amber

(1) (2)

Insert the key.* Press the “POWER” switch without depressing the brake pedal. Each press changes the hybrid system from “OFF” mode to “ACC” (accessories such as the radio on), to “IG- ON” (all accessories on) and then back to “OFF”. The indicator color on the “POWER” switch tells you which mode is se- lected.

Switching by each press

You do not need to insert the key on the vehicle with smart entry and start system. (For details, see “Smart entry and start system” in the Owner’s Manual.)

Selector lever operation

A. Starting procedure

(1) When the “READY” light comes on, move the selector lever into “D” or “R” and release it with the brake pedal depressed. The “D” or “R” position is selected and the lever returns to its original position. You can confirm which position is selected with the in- dicator in the instrument cluster. Release the parking brake and your foot from the brake pedal gradually, and then start your Prius by depress- ing the accelerator pedal assuredly.

(2)

— See Owner’s Manual for details —

Information Guide

B. Stopping procedure

(1)

(2)

Stop your Prius completely by de- pressing the brake pedal and then ap- ply the parking brake. Press the “P” position switch. The in- dicator on the switch comes on and transaxle is locked to “P”.

Note: Be sure to put the hybrid transaxle into “P” when parking. During traffic jams, use the “D” position and continue driving in that position. The battery cannot be charged in “N”. When releasing the accelerator pedal in “B”, engine braking will be applied stronger than in “D”. Compared with ordinary vehicles, you may feel less powerful engine braking during high speed driving.

For environment friendly and economical driving

(1)

(2)

Avoid abrupt acceleration or deceleration. This will ensure that sufficient power supply remains in the hybrid vehicle battery and will enable you to drive efficiently. Check the tire inflation pressure frequently to keep it at the proper level.

Note: Trip information (Consumption, energy monitor) can be shown in the multi- informa- tion display. Use this information for driving with good fuel economy. To see the information, press “INFO” (located outside the display) and touch “Trip Info.” (located inside the display).

On the side of the rear right seatback, there is an air vent provided to cool the hybrid vehicle battery. Do not put luggage or block the vent. If the vent is covered, the hybrid vehicle battery will overheat, and this may cause lower vehicle output and reduced performance.

— See Owner’s Manual for details — Printed in Japan 01- 0308- 00

01999- 47466 U 2