2010 Toyota Highlander Owners Manual

■Certifications for the engine immobilizer system

●For vehicles sold in the U.S.A.

Vehicles without smart key system

FCC ID: MOZRI-20BTY

Vehicles with smart key system

FCC ID: NI4TMIMB-1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

117

1-6. Theft deterrent system

118

1-6. Theft deterrent system

●For vehicles sold in Canada This device complied with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

119

1-6. Theft deterrent system

120

1-6. Theft deterrent system

NOTICE

■To prevent damage to the key

Do not modify, remove or disable the engine immobilizer system. If any unauthorized changes or modifications are made, the proper opera- tion of the system cannot be guaranteed.

121

1-6. Theft deterrent system Alarm∗

The system sounds the alarm and flashes the lights when forcible entry is detected. ■ Triggering of the alarm

The alarm is triggered in the following situations. ● A locked door is unlocked or opened in any way other than using the wireless remote control door lock function or entry function (vehicles with smart key system). The doors will lock again automatically.

● The hood is opened while the vehicle is locked. ● The locked glass hatch is opened in any way other than using the wireless remote control door lock function or entry function (vehicles with smart key system).

● The battery is reconnected.

122

∗: If equipped

1

1-6. Theft deterrent system

■ Setting the alarm system

Vehicles without navigation system

Vehicles with navigation system

Close the doors and hood, and lock all doors using the wireless remote control door lock function or entry function (vehicles with smart key sys- tem). The system will be set automatically after 30 sec- onds. The light changes from being on to flashing when the system is set.

indicator

Close the doors and hood, and lock all doors using the wireless remote control door lock function or entry function (vehicles with smart key sys- tem). The system will be set automatically after 30 sec- onds. The light changes from being on to flashing when the system is set.

indicator

123

1-6. Theft deterrent system

■ Deactivating or stopping the alarm

Unlock the doors using the wireless remote control door lock function or the entry function (vehicles with smart key system).

■Items to check before locking the vehicle

To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following. ●Nobody is in the vehicle. ●The windows and moon roof are closed before the alarm is set. ●No valuables or other personal items are left in the vehicle.

■Panic mode

→P. 56

■When the battery is disconnected Be sure to cancel the alarm system. If the battery is disconnected before canceling the alarm, the system may be triggered when the battery is reconnected. ■When using the key to unlock the doors

Deactivate the alarm.

124

1-6. Theft deterrent system Theft prevention labels (U.S.A.)

These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.

125

1-7. Safety information Correct driving posture

Drive in a good posture as follows:

and to

Sit upright and well back in the seat. (→P. 79) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily the extent depressed required. (→P. 79) Adjust the seatback so that the controls are easily oper- able. Adjust the tilt and telescopic positions of the steering wheel downward so the air- bag is facing your chest. (→P. 100) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (→P. 91) Wear the seat belt correctly. (→P. 94)

126

1-7. Safety information

CAUTION

■While driving

●Do not adjust the position of the driver's seat while driving.

Doing so could cause the driver to lose control of the vehicle.

●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.

●Do not place anything under the front seats.

Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent. The adjustment mechanism may also be damaged.

■Adjusting the seat position

●Take care when adjusting the seat position to ensure that other passen-

gers are not injured by the moving seat.

●Do not put your hands under the seat or near the moving parts to avoid

injury. Fingers or hands may become jammed in the seat mechanism.

127

1-7. Safety information SRS airbags

The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.

Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components. Driver knee airbag Can help provide driver protection.

Side and curtain shield airbags Side airbags Can help protect the torso of the front seat occupants. Curtain shield airbags Can help protect primarily the head of outside occupants.

128

Airbag system components

1-7. Safety information

Curtain shield airbags Side airbags Front passenger airbag Side and curtain shield air- bag sensors Front airbag sensors Front passenger’s seat belt buckle switch Curtain shield airbag sen- sors “AIR BAG ON” and “AIR BAG OFF” indicator lights

SRS warning light Driver airbag Driver’s seat position sen- sor Driver’s seat belt buckle switch Driver knee airbag Airbag sensor assembly Occupant detection system (ECU and sensors)

Your vehicle is equipped with ADVANCED AIRBAGS designed based on US motor vehicle safety standards (FMVSS208). The airbag sys- tem controls airbag deployment power for the driver and front pas- senger. The driver airbag system consists of the driver seat's position sensor etc. The front passenger's airbag system consists of the front passenger occupant classification sensor etc.

129

1-7. Safety information

The main SRS airbag system components are shown above. The SRS airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sensor and an airbag sensor. In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. A chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants.

■SRS warning light

This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensor assemblies, curtain shield air- bag sensor assemblies, driver's seat position sensor, driver's seat belt buckle switch, front passenger occupant classification system, “AIR BAG ON” and “AIR BAG OFF” indicator lights, front passenger’s seat belt buckle switch, front seat belt pretensioner assemblies, inflators, interconnecting wir- ing and power sources. (→P. 511)

■If the SRS airbags deploy (inflate)

●Bruising and slight abrasions may result from contact with a deploying

(inflating) SRS airbag.

●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, and parts of the front and rear pillars and roof side rail, may be hot for several minutes. The airbag itself may also be hot.

●The windshield may crack.

130

1

1-7. Safety information

■Operating conditions (front airbags)

●The SRS front airbags will deploy if the severity of the frontal impact is above the designed threshold level, comparable to an approximate 15
mph (25 km/h) collision when the vehicle impacts straight into a fixed bar- rier that does not move or deform. However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision (e.g. a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck, etc.).

●It is possible that in some collisions where the forward deceleration of the vehicle is very close to the designed threshold level, the SRS front air- bags and the seat belt pretensioners may not activate together.

●The SRS front passenger airbag will not activate if there is no passenger sitting in the front passenger seat. However, the front passenger airbag may deploy if luggage is put in the seat, or the seat belt is fastened, even if the seat is unoccupied. (→P. 140) ■Operating conditions (side airbags)

●The SRS side airbags are designed to inflate when the passenger com-

partment is subjected to a severe impact from the side.

●The SRS side airbag on the passenger seat will not activate if there is no passenger sitting in the front passenger seat. However, the side airbag on the passenger seat may deploy if luggage is put in the seat, or the seat belt is fastened, even if the seat is unoccupied. (→P. 140)

■Operating conditions (curtain shield airbags)

The SRS curtain shield airbags are designed to inflate when the passenger compartment is subjected to a severe impact from the side or vehicle roll- over.

131

1-7. Safety information

■Conditions under which the SRS airbags may deploy (inflate), other

than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

●Hitting a curb, edge of pavement or

hard surface

●Falling into or jumping over a deep hole ●Landing hard or vehicle falling

The SRS curtain shield airbags may also deploy under the situation shown in the illustration.

●The angle of vehicle tip-up is marginal. ●The vehicle skids and hits a curb stone.

■Types of collisions that may not deploy the SRS airbag (front airbags) The SRS front airbags are generally not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision. But, whenever a collision of any type causes suffi- cient forward deceleration of the vehicle, deployment of the SRS front air- bags may occur.

●Collision from the side ●Collision from the rear ●Vehicle rollover

132

1-7. Safety information

■Types of collisions that may not deploy the SRS airbag

(side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.

●Collision from the side to the vehicle body other than the passenger com- partment

●Collision from the side at an angle

The SRS side airbags are not generally designed to inflate if the vehicle is involved in a frontal or rear collision, if it rolls over, or if it is involved in a low- speed side collision.

●Collision from the front ●Collision from the rear ●Vehicle rollover

The SRS curtain shield airbags are not generally designed to inflate if the vehicle is involved in a frontal or rear collision, if it pitches end over end, or if it is involved in a low-speed side collision.

●Collision from the front ●Collision from the rear ●Pitching end over end

133

1-7. Safety information

■When to contact your Toyota dealer

In the following cases, contact your Toyota dealer as soon as possible. Do not disconnect the battery cables before contacting your Toyota dealer. ●Any of the SRS airbags have been inflated.

●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS airbags to inflate.

●A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield airbags to inflate.

●The pad section of the steering wheel or dashboard or lower portion of the instrument panel is scratched, cracked, or otherwise damaged.

●The surface of the seats with the side airbag is scratched, cracked or other- wise damaged.

●The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked or other- wise damaged.

134

1-7. Safety information

CAUTION

■SRS airbag precautions

Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ●The driver and all passengers in the vehicle must wear their seat belts

properly. The SRS airbags are supplemental devices to be used with the seat belts. ●The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (“NHTSA”) advises:

Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag provides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 10 in. (250 mm) away now, you can change your driving position in several ways:

• Move your seat to the rear as far as you can while still reaching the

pedals comfortably.

• Slightly recline the back of the seat.

Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature. • If your steering wheel is adjustable, tilt it downward. This points the air-

bag toward your chest instead of your head and neck.

The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.

135

1-7. Safety information

CAUTION

■SRS airbag precautions

●If the seat belt extender has been con- nected to the driver's seat belt buckle but the seat belt extender has not also been fastened to the latch plate of the driver's seat belt, the SRS driver's air- bag system will judge that the driver is wearing the seat belt even though the seat belt has not been connected. In this case, the driver's airbag may not activate correctly in a collision, resulting in death or serious injury in the event of collision. Be sure to wear the seat belt with the seat belt extender.

●The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air- bag as possible with the seatback adjusted, so the front passenger sits upright.

●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children. (→P. 146)

136

1-7. Safety information

CAUTION

■SRS airbag precautions

●Do not sit on the edge of the seat or

lean against the dashboard.

●Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.

●Do not drive the vehicle while the driver or passenger has items resting on their knees.

●Do not lean against the door, the roof side rail or the front, side and rear pil- lars.

●Do not allow anyone to kneel on the passenger seat toward the door or put their head or hands outside the vehicle.

137

1-7. Safety information

CAUTION

■SRS airbag precautions

●Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad or lower portion of the instrument panel. These items can become projectiles when SRS driver, front passenger and knee airbags deploy.

●Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip.

●Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and seriously injure or kill you, should the SRS curtain shield airbag deploy.

●Vehicles without smart key system: Do not attach any heavy, sharp or hard objects such as keys or accessories to the key. The objects may restrict the SRS knee airbag inflation or be thrust into the driver's seat area by the force of the deploying airbag, thus causing a danger.

●If the vinyl cover is put on the area where the SRS knee airbag will deploy,

be sure to remove it.

●Do not use seat accessories which cover the parts where the SRS side

airbags inflate as they may interfere with inflation of the airbags.

●Do not strike or apply significant levels of force to the area of the SRS air-

bag components (→P. 129). Doing so can cause the SRS airbags to malfunction.

138

1-7. Safety information

CAUTION

■SRS airbag precautions

●Do not touch any of the component parts immediately after the SRS air-

bags have deployed (inflated) as they may be hot.

●If breathing becomes difficult after the SRS airbag has deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.

●If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.

■Modification and disposal of SRS airbag system components

Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. ●Installation, removal, disassembly and repair of the SRS airbags. ●Repairs, modifications, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rails.

●Repairs or modifications of the front fender, front bumper, or side of the

occupant compartment.

●Installation of snow plows, winches, etc. to the front grille (bull bars, kan-

garoo bar etc.).

●Modifications to the vehicle's suspension system. ●Installation of electronic devices such as mobile two-way radios or CD

players.

●Modifications to your vehicle for a person with a physical disability.

139

1-7. Safety information Front passenger occupant classification system

Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for front passenger.

Vehicles without navigation system

Vehicles with navigation system

SRS warning light “AIR BAG OFF” indicator light “AIR BAG ON” indicator light Front passenger's seat belt reminder light

140

1

1-7. Safety information

Conditions and operation of the front passenger occupant classification system ■ Adult*1

Indicator/

warning light

Devices

“AIR BAG ON” and “AIR BAG OFF” indi-

cator lights

SRS warning light

Front passenger's seat belt reminder

light

Front passenger airbag

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Front passenger's seat belt pretensioner

“AIR BAG

ON” Off

Flashing*2

Activated

■ Child*3 or child restraint system*4

Indicator/

warning light

Devices

“AIR BAG ON” and “AIR BAG OFF” indi-

cator lights

SRS warning light

Front passenger's seat belt reminder

light

Front passenger airbag

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Front passenger's seat belt pretensioner

“AIR BAG OFF”*5

Off

Flashing*2

Deactivated

Activated

141

1-7. Safety information

■ Unoccupied

Indicator/

warning light

Devices

“AIR BAG ON” and “AIR BAG OFF” indi-

cator lights

SRS warning light

Front passenger's seat belt reminder

light

Front passenger airbag

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Not illumi-

nated

Off

Deactivated

Activated

Front passenger's seat belt pretensioner Deactivated

■ There is a malfunction in the system

Indicator/

warning light

Devices

“AIR BAG ON” and “AIR BAG OFF” indi-

cator lights

SRS warning light

Front passenger's seat belt reminder

light

Front passenger airbag

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Front passenger's seat belt pretensioner

“AIR BAG

OFF” On

Off

Deactivated

Activated

*1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture.

*2: In the event the front passenger does not wear a seat belt. *3: When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/ her as an adult depending on his/her physique or posture.

142

1-7. Safety information

*4: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 147)

*5: In case the indicator is not illuminated, consult this manual as for

installing the child restraint system properly. (→P. 151)

143

1-7. Safety information

CAUTION

■Front passenger occupant classification system precautions

Observe the following precautions regarding front passenger occupant clas- sification system. Failure to do so may cause death or serious injury. ●Wear the seat belt properly. ●Make sure the front passenger's seat belt tab has not been left inserted

into the buckle before someone sits in the front passenger seat.

●Make sure the “AIR BAG OFF” indicator light is not illuminated when using the seat belt extender for the front passenger seat. If the “AIR BAG OFF” indicator light is illuminated, disconnect the extender tongue from the seat belt buckle, then reconnect the seat belt. Reconnect the seat belt extender after making sure the “AIR BAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIR BAG OFF” indicator light is illumi- nated, the front passenger airbag, side airbag on the front passenger side may not activate correctly, which could cause death or serious injury in the event of collision.

●Do not apply a heavy load to the front passenger seat or equipment (e.g.

seatback pocket).

●Do not put weight on the front passenger seat by putting your hands or

feet on the front passenger seat seatback from the rear passenger seat.

●Do not let a rear passenger lift the front passenger seat with their feet or

press on the seatback with their legs.

●Do not put objects under the front passenger seat. ●Do not recline the front passenger seatback so far that it touches a rear seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger's airbags will not deploy in the event of a severe accident. If the seatback touches the rear seat, return the seat- back to a position where it does not touch the rear seat. Keep the front passenger seatback as upright as possible when the vehicle is moving. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.

144

1

1-7. Safety information

CAUTION

■Front passenger occupant classification system precautions

●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remains illuminated, either ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.

●When it is unavoidable to install the forward-facing child restraint system on the front passenger seat, install the child restraint system on the front passenger seat in the proper order. (→P. 151)

●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.

●Child restraint systems installed on the rear seat should not contact the

front seatbacks.

●Do not use a seat accessory, such as a cushion or seat cover, that covers

the seat cushion surface.

●Do not modify or replace the upholstery of the front seat.

145

1-7. Safety information Child restraint systems

A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.

Points to remember

Studies have shown that installing a child restraint on a rear seat is much safer than installing one to the front passenger seat. ● Choose a child restraint system that suits your vehicle and is

appropriate to the age and size of the child.

● For installation details, follow the instructions provided with the

child restraint system. General installation instructions are provided in this manual. (→P. 151)

146

1-7. Safety information

Types of child restraints

Child restraint systems are classified into the following 3 types according to the age and size of the child.

Rear facing ⎯ Infant seat/convertible seat

Forward facing ⎯ Convertible seat

Booster seat

147

1-7. Safety information

■Selecting an appropriate child restraint system

●Use a child restraint system appropriate for the child until the child

becomes large enough to properly wear the vehicle’s seat belt.

●If a child is too large for a child restraint system, sit the child on a rear

seat and use the vehicle's seat belt. (→P. 94)

CAUTION

■Child restraint precautions

●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.

●Never install a rear-facing child restraint system on the front passenger

seat even if “AIR BAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag can cause death or serious injury to the child if the rear-fac- ing child restraint system is installed on the front passenger seat.

148

1

1-7. Safety information

CAUTION

■Child restraint precautions

●A forward-facing child restraint system may be allowed to be installed on the front passenger seat only when it is unavoidable. A child restraint sys- tem that requires a top tether strap should not be used in the front passen- ger seat since there is no top tether strap anchor for the front passenger seat. Adjust the seatback as uprights as possible and always move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illuminated, because the front passenger airbag could inflate with consid- erable speed and force. Otherwise, the child may be killed or seriously injured.

●Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of an accident.

●Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side air- bags and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.

●Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop or an accident. ■Child restraint lock function belt precaution

Do not allow children to play with the child restraint lock function belt. If the belt becomes twisted around a child’s neck, it will not be possible to pull the belt out leading to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.

149

1-7. Safety information

CAUTION

■When the child restraint system is not in use

●Keep the child restraint system properly secured on the seat even if it is

not in use. Do not store the restraint unsecured in the passenger compartment.

●If it is necessary to detach the child restraint system, remove it from the vehicle or store it securely in the luggage compartment. This will prevent it from injuring passengers in the event of a sudden stop or accident.

150

1-7. Safety information Installing child restraints

Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.

Second seat: Child restraint LATCH anchors

LATCH anchors are provided for the rear outside seats. (But- tons displaying the location of the anchors are attached to the seats.)

Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt)

151

1-7. Safety information

Second seat: Anchor brackets (for top tether strap)

Anchor brackets are provided for the second seats.

152

Installation with LATCH system

STEP 1

1-7. Safety information

Fold the seatback while pulling the lever. Return the seatback and secure it at the 1st lock posi- tion (most upright position). Adjust the seatback to the 3rd lock position. (→P. 82)

Type A

STEP 2

Canada only

1st lock position 3rd lock position

Latch the hooks of the lower straps onto the LATCH anchors. The bars are installed in the clearance between the seat cush- ion and seatback. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchors.

For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.

153

the buckles onto

Latch LATCH anchors.

the

The bars are installed in the clearance between the seat cush- ion and seatback. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchors.

For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.

1-7. Safety information

Type B

STEP 2

Canada only

154

1-7. Safety information

Installing child restraints using a seat belt (child restraint lock function belt)

■ Rear facing ⎯ Infant seat/convertible seat STEP 1

Place the child seat on the rear seat facing the rear of the vehi- cle.

STEP 2

STEP 3

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

then allow

Fully extend the shoulder belt and to retract slightly in order to activate the ALR lock mode.

it

Lock mode allows the seat belt to retract only.

155

1-7. Safety information

STEP 4

While pushing the child seat down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

■ Forward facing ⎯ Convertible seat STEP 1

Place the child seat on the seat facing the front of the vehicle.

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

it

then allow

Fully extend the shoulder strap and to retract slightly into the ALR lock mode. Lock mode allows the seat belt to retract only.

STEP 2

STEP 3

156

1

STEP 4

1-7. Safety information

While pushing the child seat into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchors.

STEP 5

■ Booster seat STEP 1

STEP 2

Place the booster seat on the seat facing the front of the vehi- cle.

Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer's instructions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child's shoulder, and that the lap belt is as low as possible. (→P. 94)

157

1-7. Safety information

Removing a child restraint installed with a seat belt

Push the buckle release button and fully retract the seat belt.

Child restraint systems with a top tether strap (second seat only)

STEP 1

Secure the child restraint using the seat belt or lower anchors, and adjust the head restraint to the upmost position.

158

1

STEP 2

Front of vehicle

STEP 3

1-7. Safety information

Outside seat: Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap. Center seat: Latch the hook onto the anchor bracket and tighten the top tether strap.

Make sure the top tether strap is securely latched. Hook Top strap Anchor bracket

Adjust the head restraint to the downmost position.

■Laws and regulations pertaining to anchorages

The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819.

159

1-7. Safety information

CAUTION

■When installing a booster seat

Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode. (→P. 95) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.

■When installing a child restraint system

Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking or an accident.

●If the driver's seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.

●Adjust the front passenger seat or sec- ond seats so that it does not interfere with the child restraint system.

●Only put a forward-facing or booster child seat on the front seat when unavoidable. When installing a forward- facing or booster child seat on the front passenger seat, move the seat as far back as possible even if “AIR BAG OFF” indicator light is illuminated. Fail- ing to do so may result in death or seri- ous injury if the airbags deploy (inflate).

160

1

1-7. Safety information

CAUTION

■When installing a child restraint system

●When installing a child restraint system in the rear center seat, adjust both seat cushions to the same position and align seatbacks at the same angle. The seatbacks must be adjusted to the same angle. Otherwise, the child restraint system cannot be securely restrained and this may cause death or serious injuries in an accident.

●When using the LATCH anchors for a child restraint system, move the seat as far back as possible (second seat only), with the seatback close to the child restraint system.

●When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder. Failing to do so may result in death or serious injury in the event of an accident or sudden braking.

●Ensure that the belt and tab are securely locked and the seat belt is not

twisted.

●Push and pull the child seat from side to side and forward to be sure it is

secure.

●After securing a child restraint system, never adjust the seat. ●Follow all installation instructions provided by the child restraint system

manufacturer.

■Do not use a seat belt extender

If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of an accident.

■To correctly attach a child restraint system to the anchors

When using the LATCH anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of a sudden stop or an accident.

161

1-7. Safety information

162

2-2. Instrument cluster Gauges and meters

Vehicles without smart key system The following gauges and meters illuminate when the engine switch is in the “ON” position. Vehicles with smart key system The following gauges and meters illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode. Tachometer Displays the engine speed in revolutions per minute. Engine coolant temperature gauge Displays the engine coolant temperature. Fuel gauge Displays the quantity of fuel remaining in the tank. Speedometer Displays the vehicle speed. Odometer/trip meter switching and trip meter resetting button Switches between odometer and trip meter displays. Pushing and hold- ing the button will reset the trip meter when the trip meter is being dis- played.

188

2-2. Instrument cluster

Odometer/Trip meter

Odometer Displays the total distance the vehicle has been driven. Trip meter Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker When the headlight switch is turned on, the brightness will be reduced slightly unless the control dial is turned fully up.

NOTICE

■To prevent damage to the engine and its components

●Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

●The engine may be overheating if the temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 545)

189

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster

Center panel (vehicles without navigation system)

190

Center panel (vehicles with navigation system)

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Turn signal indicator (→P. 185)

Headlight high beam indicator (→P. 205)

Downhill assist control system indicator (→P. 225)

Slip indicator (→P. 219)

(U.S.A.)

(Canada)

(if equipped)

Headlight indicator (→P. 203)

Tail light indicator (→P. 203)

Front fog light indicator (→P. 207)

“SNOW” indicator (→P. 181)

(4WD models)

191

2-2. Instrument cluster

Shift position and shift range indica- tors (→P. 180)

(if equipped)

Enhanced VSC off indi- cator (→P. 220) Engine immobilizer/ alarm indicator (→P. 115, 122)

SRS airbag on-off indi- cator (→P. 140)

Cruise control indicator (→P. 211)

“TRAC OFF” indicator (→P. 219)

*: These lights turn on when the engine switch is turned to the “ON” position (vehicles without smart key system) or the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) to indicate that a system check is being performed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 510)

*1

*1

(Canada) *1

(U.S.A.) *1, 2

(U.S.A.)

(U.S.A.) *4

*1

*1

*5

*1, 2

*1

*1

*1

*1

(Canada) *1, 2

(U.S.A.) *1, 2

(Canada)

*1

*3

192

2

2-2. Instrument cluster

*1: These lights turn on when the engine switch is turned to the “ON” position (vehicles without smart key system) or the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

*2: Vehicles without multi-information display *3: Vehicles with multi-information display *4: Vehicles without navigation system *5: Vehicles with navigation system

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS and SRS airbag warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

193

2-2. Instrument cluster Multi-information display∗

The multi-information display presents the driver with a variety of driving-related data, including the current outside temperature and clock.

● Outside temperature

Indicates the outside tempera- ture. The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).

● Clock

(→ P. 197)

Indicates and sets the time.

● Trip information (→P. 195) Displays cruising range, fuel consumption and other cruis- ing-related information.

● Automatic air conditioning system display (if equipped) (→P. 263) Automatically displayed when the automatic air conditioning is turned on.

● Rear view monitor

(→P. 214) (if equipped) Automatically displayed when the shift lever is moved into the R position.

194

∗: If equipped

2-2. Instrument cluster

● Warning messages

(→P. 521) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.

Trip information

Push the “DISP” button to dis- play trip information. Display items can be switched by pressing the “DISP” button.

■ Average fuel consumption after refueling

Displays the average fuel consumption since the vehicle was last refueled.

■ Instantaneous fuel consumption

Displays the instantaneous fuel consumption.

■ Cruising range

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis- played.

• When only a small amount of fuel is added to the tank, the display may

not be updated. ■ Driving distance

Displays the driving distance since the engine was started.

195

2-2. Instrument cluster

■ Average fuel consumption

Displays the average fuel consumption since the function was reset. This function can be reset by pressing the “DISP” button for longer than one second when the average fuel consumption is displayed. When the function is reset, the previous five average fuel consumption values will automatically be displayed for six seconds.

■ Average fuel consumption history

Displays the previous five average fuel consumption values.

Setting up the displays

Display the set up screen on the multi-information display when the vehicle is stopped.

Press and hold the “DISP” button to display the set up screen.

Select the desired item on the menu screen.

Press and hold the “DISP” button to enter the setting mode.

STEP 1

STEP 2

196

2-2. Instrument cluster

■ Setting the clock STEP 1

Select “CLOCK” on the menu screen. Press and hold the “DISP” button until the display changes.

STEP 2

STEP 3

Press the “DISP” button to adjust the hours.

After adjusting the hours, wait 5
seconds to allow the hours to be automatically input.

Press the “DISP” button to adjust the minutes.

After adjusting the minutes, wait 5
seconds to allow the minutes to be automatically input.

197

2-2. Instrument cluster

■ Setting the display STEP 1

Select “DISPLAY” on the menu screen. Press and hold the “DISP” button until the display changes.

STEP 2

Select the desired item on the menu screen.

Press and hold the “DISP” button to enter the setting mode.

● Setting the day mode STEP 1

STEP 2

Select “DAY MODE” on the menu screen. Press and hold the “DISP” button until the display changes. Press the “DISP” button to select “ON” or “OFF”. After setting the day mode, wait 5 seconds to allow the mode to be automatically input.

● Setting the background color STEP 1

Select “BACKGROUND COLOR” on the menu screen. Press and hold the “DISP” button until the display changes. Press the “DISP” button to select “BLACK” or “BLUE”. After selecting a background color, wait 5 seconds to allow the color to be automatically input.

STEP 2

198

2

2-2. Instrument cluster

● Setting the brightness STEP 1

Select “BRIGHTNESS” on the menu screen. Press and hold the “DISP” button until the display changes.

STEP 2

Press the “DISP” button to adjust the brightness. +: Brighter -: Darker

the brightness, After adjusting wait 5 seconds to allow the bright- ness to be automatically input.

● Setting the contrast STEP 1

Select “CONTRAST” on the menu screen. Press and hold the “DISP” button until the display changes.

STEP 2

Press the “DISP” button to adjust the contrast. +: Strengthen -: Weaken

After adjusting the contrast, wait 5
seconds to allow the contrast to be automatically input.

● Returning to the previous screen

Select “RETURN” on the menu screen. Press and hold the “DISP” button until the display changes.

199

2-2. Instrument cluster