2010 Toyota Highlander Owners Manual

Selecting “List names” by using a voice command begins reading the list of the registered data. When listing is complete, the system returns to “Phonebook”. Pressing the following function will be available. • Dialing: “Dial” • Changing a registered name: “Change Name” • Deleting an entry: “Delete Entry” • Setting speed dial: “Set Speed Dial (Speed Dial)”

■Limitation of number of digits

A phone number that exceeds 24 digits cannot be registered.

371

3-5. Using the interior lights Interior lights list

Your Toyota is equipped with the illuminated entry system to assist in entering the vehicle. Owing to the function of the system, the lights shown in the following illustration automatically turn on/off according to the presence of the electronic key (vehicles with smart key system), whether the doors are locked/unlocked, whether the doors or glass hatch (if equipped) are opened/closed, and the “ENGINE START STOP” switch mode or the engine switch position.

Outer foot lights (vehicles with smart key system) Personal/interior lights (→P. 373) Engine switch light (vehicles without smart key system) Front door courtesy light Personal/interior light or interior light (→P. 373, 374) Interior light (→P. 374)

372

Personal/interior light main switch and personal/interior lights

3-5. Using the interior lights

Personal/interior light main switch

“OFF” The personal/interior lights and interior light can be individually turned on or off. Door position The personal/interior lights and interior light come on when a door or the glass hatch (if equipped) is opened. They turn off when the doors and glass hatch are closed. On The personal/interior lights and interior light cannot be individually turned off.

Personal/interior lights

Front

On/off

The illuminated entry system is activated even is turned off when the personal/inte- rior light main switch is in door position.

light

the

if

373

3-5. Using the interior lights

Personal/interior lights and interior light

Center (if equipped)

On/off

The illuminated entry system is activated even is turned off when the personal/inte- rior light main switch is in door position.

light

the

if

Interior light

Center (if equipped)

Rear

Off On The illuminated entry system is activated even is turned off when the personal/inte- rior light main switch is in door position.

light

the

if

■To prevent the battery discharge

If the lights remain on when the door is not fully closed and the personal/inte- rior light main switch is in door position, the lights will go off automatically after 20 minutes.

■Customization that can be configured at Toyota dealer

Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 582)

374

3-6. Using the storage features List of storage features

Auxiliary boxes Overhead console Glove box Bottle holders Cup holders Side table Console box Auxiliary box & cup holder

375

3-6. Using the storage features

Glove box

Glove box

Unlock with the master key (vehicles without smart key system) or mechanical key (vehicles with smart key sys- tem) Lock with the master key (vehicles without smart key system) or mechanical key (vehicles with smart key sys- tem) Open (pull lever)

■Power back door main switch (vehicles with power back door)

The power back door main switch is located in the glove box. (→P. 73)

CAUTION

■Caution while driving

Keep the glove box closed. Injuries may result in the event of an accident or sudden braking.

376

Console box

Upper

3-6. Using the storage features

Console box

Pull up the knob to release the lock. Lift the lid.

Lower

Push down the lever.

CAUTION

■Caution while driving

Keep the console box closed. Injuries may result in the event of an accident or sudden braking.

377

3-6. Using the storage features

Overhead console

Overhead console

The overhead console is useful for temporarily storing sunglasses and similar small items.

Press in the lid.

CAUTION

■Items that should not be left in the overhead console

Do not leave glasses or lighters in the console. If the interior of the vehicle becomes hot, lighters may explode and glasses may warp or become cracked.

■Caution while driving

Do not leave the overhead console open while driving. Items stored in it may fall out and cause injury.

■Size of stored items

Do not put large items in the overhead console. The overhead console may not be able to be shut from the conversation mir- ror state.

■Maximum storage weight

Do not place any object heavier than 0.4 lb. (200 g) in it. The console may be opened and cause injury.

378

Cup holders

Front (type A)

3-6. Using the storage features

Cup holders

Removing the adapters changes the size. (→P. 381)

Front (type B)

Lift the lid.

Console box

Pull out the cup holder.

379

3-6. Using the storage features

Side table

Cup holders

Install the side table before using the cup holder. (→P. 386) Removing the adapters changes the size. (→P. 381)

Rear (vehicles without third seat)

Rear (vehicles with third seat)

Removing the adapters changes the size. (→P. 381)

380

3-6. Using the storage features

Cup holders

■Adjusting size of the cup holder (front [type A], front [type B], side

table, rear [vehicles with third seats])

Front (type A)

Remove the adapter.

Front (type B)

Remove the separator.

Side table

Remove the adapter.

Rear (vehicles with third seat)

Remove the adapter.

381

3-6. Using the storage features

Cup holders

CAUTION

■Items unsuitable for the cup holder

Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury. If possible, cover hot drinks to prevent burns.

■When not in use

Front (type B) and console box cup holders: Keep the cup holders closed. Injuries may result in the event of an accident or sudden braking.

382

3-6. Using the storage features

Bottle holders

Bottle holders

Front

Rear

CAUTION

■Items unsuitable for the bottle holder

Do not place anything other than a bottle in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.

NOTICE

■When stowing a bottle

Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders. The contents may spill.

383

3-6. Using the storage features

Auxiliary boxes

Type A

Auxiliary boxes

Pull up the lever.

Type B

Lift the lid.

Remove the separator to use the box. (→P. 381)

Type C (if equipped)

Lift the lid.

384

3-6. Using the storage features

Auxiliary boxes

Type D

Lift the lid.

■Auxiliary box (type D)

Install the side table. (→P. 386)

CAUTION

■Caution while driving

Keep the auxiliary boxes closed. Injuries may result in the event of an accident or sudden braking.

385

3-6. Using the storage features

Side table

■ Installing the side table STEP 1

Side table

Take out the side table from the console box.

STEP 2

Remove the second center seat. (→P. 87)

STEP 3

Engage the front pins of the side table with the hooks. Push down on the side table to engage the rear pin locks.

■ Removing the side table STEP 1

Take out the second center seat from the console box.

386

STEP 2

STEP 3

STEP 4

3-6. Using the storage features

Side table

Pull the lock release lever to remove the side table.

Stow the side table in the con- sole box.

Push down on the end to engage the pins in the holes and close the console box door.

Make sure that the side table is securely locked in position.

CAUTION

■Caution while driving

Keep the console box closed. Injuries may result in the event of an accident or sudden braking.

387

3-7. Other interior features Sun visors

Forward position Flip down. Side position Flip down, unhook, and swing to the side. Side extender Place in side position then slide backwards.

388

3-7. Other interior features Vanity mirrors

Slide the cover.

The light turns on when the cover is opened. (vehicles with vanity mirror light)

NOTICE

■To prevent the battery from being discharged

Do not leave the vanity lights on for extended periods while the engine is stopped.

389

3-7. Other interior features Clock (vehicles without multi-information display)

Adjusts the hours. Adjusts the minutes.

■The clock is displayed when

The engine switch is in the “ACC” or “ON” position.

390

3-7. Other interior features Conversation mirror

Press in the lid.

Push the lid back up half way.

■To use the overhead console from the conversation mirror state

Fully close the lid, then open it again. (→P. 378)

391

3-7. Other interior features Power outlets

The power outlet can be used for a following component.

12 V: Accessories that run on less than 10 A. 115 VAC: Accessories that use less than 100 W.

■ 12 V

Type A*1

Type B*2

392

3-7. Other interior features

Type C

Type D

■ 115 VAC*3

Main switch To use the power outlet, turn on the main switch. Power outlet socket

*1: Vehicles with seat heater *2: Vehicles without seat heater *3: Vehicles with rear entertainment system

393

3-7. Other interior features

■The power outlet can be used when

12 V

Vehicles without smart key system: The engine switch is in the “ACC” or “ON” position. Vehicles with smart key system: The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.

115 VAC

Vehicles without smart key system: The engine switch is in the “ON” position. Vehicles with smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

394

3-7. Other interior features

NOTICE

■To avoid damaging the power outlet

Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.

■To prevent the fuse from being blown

12 V Do not use an accessory that uses more than 12 V 10 A. 115 VAC Do not use a 115 VAC appliance that requires more than 100 W. If a 115 VAC appliance that consumes more than 100 W is used, the pro- tection circuit will cut the power supply.

■To prevent the battery discharge

Do not use the power outlet longer than necessary when the engine is off.

■Appliances that may not operate properly (115 VAC)

The following 115 VAC appliances may not operate properly even if their power consumption is under 100 W. ●Appliances with high initial peak wattage ●Measuring devices that process precise data ●Other appliances that require an extremely stable power supply

395

3-7. Other interior features Seat heaters∗

Driver's seat

Front passenger's seat

Pops the knob out On The indicator light comes on. Adjusts the seat tempera- ture The further you turn the knob clockwise, the warmer the seat becomes.

■The seat heaters can be used when Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

■When not in use

Turn the knob fully counterclockwise. The indicator light turns off. Press the knob into the recessed position.

396

∗: If equipped

3-7. Other interior features

CAUTION

■Burns

●Use caution when seating the following persons in a seat with the seat

heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the disabled • Persons with sensitive skin • Persons who are fatigued • Persons who have taken alcohol or drugs that induce sleep (sleeping

drugs, cold remedies, etc.)

●Do not cover the seat with anything when using the seat heater.

Using the seat heater with a blanket or cushion increases the temperature of the seat and may lead to overheating.

NOTICE

■To prevent seat heater damage

Do not put unevenly weighted objects on the seat and do not stick sharp objects (needles, nails, etc.) into the seat.

■To prevent battery discharge

Turn the switches off when the engine is not running.

397

3-7. Other interior features Armrests

Pull the armrest down for use.

NOTICE

■To prevent damage to the armrest

Do not place too much strain on the armrest.

398

3-7. Other interior features Floor mat

Securely place a mat that matches the size of the space on the car- pet.

Secure the driver's floor mat using the hooks provided.

CAUTION

■When inserting the floor mat

Observe the following precautions. Failure to do so may result in the floor mat slipping and interfering with the movement of the pedals during driving, resulting in an accident. ●Make sure the floor mat is properly placed on the vehicle carpet and the

correct side faces upward.

●Do not place floor mats on top of existing mats.

399

3-7. Other interior features Luggage compartment features

■ Cargo hooks

Cargo hooks are provided for securing loose items.

■ Shopping bag hooks

■ Auxiliary box

Lift the center deck board.

400

3-7. Other interior features

■ Separating luggage compartment

The center deck board can be used to separate the luggage compartment. Remove the center deck board and insert it upright into the groove.

The board cannot be inserted when the luggage cover is stowed.

401

3-7. Other interior features

■ Luggage cover (vehicles with luggage cover) STEP 1

Hang the hooks on the hook brackets on the second seat seatback.

Vehicles with the third seat: When using the luggage cover, the third seat must be fold down. (→P. 86)

Pull out the luggage cover and engage both ends to secure it.

STEP 2

■ When taking out luggage through the glass hatch (vehicles with glass hatch) Pull the luggage cover to disengage both ends.

STEP 1

Engage both ends of the luggage cover with the grooves shown in the illustration and stand the cover upright.

STEP 2

402

3-7. Other interior features

■Removing the luggage cover (vehicles with luggage cover)

The luggage cover can be removed by following the procedure below.

Detach the hooks. Push in the left side of the luggage cover while keeping hold of the right side. Then raise the right side and pull the luggage cover out.

■Luggage storage box (vehicles without third seat)

STEP 1

Lift the deck board.

STEP 2

Secure the board using the hook.

403

3-7. Other interior features

■Stowing the luggage cover (vehicles with luggage cover)

STEP 1

STEP 2

STEP 3

Remove the side deck boards and open the center deck board.

Fold the flaps on top of the luggage cover with the hooks rolled inside.

Place the left end of the luggage cover in the recess on the left-hand side and then lower the right end into the recess on the right-hand side.

CAUTION

■When the cargo hooks are not in use

To avoid injury, always return the cargo hooks to their positions when they are not in use.

■Caution while driving

Do not drive with any of the deck boards opened. Items may fall out and cause injury.

404

3-7. Other interior features

NOTICE

■Shopping bag hook weight capacity

Do not hang any object heavier than 4 lb. (2 kg) on shopping bag hooks.

■While driving

Do not drive with the luggage cover standing upright in the grooves as the luggage cover may fall down.

■Before inserting the center deck board into the luggage compartment

Make sure the luggage cover is not stowed.

■Closing the back door (vehicles without third seat)

Do not close the back door with the hook attached, or the hook may be dam- aged.

405

3-7. Other interior features Garage door opener∗

The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, and other devices.

The garage door opener (HomeLink® Universal Transceiver) is manufac- tured under license from HomeLink®.

Programming the HomeLink® (for U.S.A. owners)

The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.

Indicator Buttons

■ Programming the HomeLink® STEP 1

Point the remote control for the device 1 to 3 in. (25 to 75 mm) from the HomeLink® control but- tons.

Keep the indicator light on the HomeLink® in view while pro- gramming.

406

∗: If equipped

STEP 2

STEP 3

3-7. Other interior features

Press and hold down one of the buttons on the HomeLink® and the button on the transmitter. When the indicator light on the HomeLink® changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

Test the operation of HomeLink® by pressing newly programmed button.

the the

the

hold

If programming a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the Rolling Code type. Press and programmed HomeLink® button. The garage door has the rolling code feature if the HomeLink®) flashes rapidly for 2
seconds and then remains lit. If your transmitter is the Rolling Code type, proceed to the head- ing “Programming a rolling code system”.

light (on

indicator

the

STEP 4

Repeat the steps above to program another device for each of the remaining HomeLink® buttons.

407

3-7. Other interior features

■ Programming a Rolling Code system (for U.S.A. owners)

If your device is Rolling Code equipped, follow the steps under the heading “Programming the HomeLink®” before proceeding with the steps listed below.

STEP 1

STEP 2

STEP 3

STEP 4

Locate the training button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener. Refer to the operation manual supplied with the garage door opener for the location of the training button. Press the training button. Press and release the vehicle’s programmed HomeLink® but- ton twice. The garage door may open. If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door. The ceiling mounted garage door opener motor should now recog- nize the HomeLink® transceiver and operate the garage door. Repeat the steps above to program another rolling code sys- tem for any of the remaining HomeLink® buttons.

■ Programming an entry gate (for U.S.A. owners)/Programming

all devices in the Canadian market

STEP 1

STEP 2

STEP 3

STEP 4

Place your transmitter 1 to 3 in. (25 to 75 mm) away from the surface of the HomeLink®. Keep the indicator light on the HomeLink® in view while program- ming. Press and hold the selected HomeLink® button. Repeatedly press and release (cycle) the device’s remote control button for two seconds each until step 4 is complete. When the indicator light on the HomeLink® compatible trans- ceiver start to flashing rapidly, release the buttons.

408

3-7. Other interior features

STEP 5

STEP 6

Test the operation of the HomeLink® by pressing the newly programmed button. Check to see if the gate/device operates correctly. Repeat the steps above to program another device for each of the remaining HomeLink® buttons.

■ Programming other devices

To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance.

■ Reprogramming a button

The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the programming instructions.

Operating the HomeLink®

Press the appropriate HomeLink® button. The HomeLink® indicator light on the HomeLink® transceiver should turn on.

The HomeLink® continues to send a signal for up to 20 seconds as long as the button is pressed.

Erasing the entire HomeLink® memory (all three programs)

Press and hold down the 2 out- side buttons for 20 seconds until the indicator light flashes.

If you sell your vehicle, be sure to erase the programs stored in the HomeLink® memory.

409

3-7. Other interior features

■Before programming

●Install a new battery in the transmitter. ●The battery side of the transmitter must be pointed away from the

HomeLink®.

■Certification for the garage door opener

This device complies with Part 15 of the FCC Rules and with RSS-210 of the IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party respon- sible for compliance could void the user's authority to operate the device.

CAUTION

■When programming a garage door or other remote control device

The garage door may operate, so ensure people and objects are out of dan- ger to prevent potential harm.

■Conforming to federal safety standards

Do not use the HomeLink® Compatible Transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards. This includes any garage door that cannot detect an obstruction object. A door or device without these features increases the risk of death or serious injury.

410

3-7. Other interior features Compass∗

The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation

To turn the compass on or off, press the switch.

■ Displays and directions

Display

NE SE SW NW

Direction

North

Northeast

East

Southeast

South

Southwest

West

Northwest

∗: If equipped 411

3-7. Other interior features

Calibrating the compass

The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle.

If you cross over a map boundary shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to the following.

■ Deviation calibration STEP 1

Stop the vehicle where it is safe to drive in a circle.

STEP 2

Press the switch until a number (1 to 15) appears on the com- pass display.

STEP 3

Press the switch, and referring to the map above, select the number of the zone where you are. If the direction is displayed several seconds after adjustment, the calibration is complete.

412

■ Circling calibration

3-7. Other interior features

When C appears on the display, drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed.

If there is not enough space to drive in a circle, drive around the block until the direction is dis- played.

■Conditions unfavorable to correct operation

The compass may not show the correct direction in the following conditions: ●The vehicle is stopped immediately after turning. ●The vehicle is on an inclined surface. ●The vehicle is in a place where the earth's magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).

●The vehicle has become magnetized.

(There is a magnet or metal object near the inside rear view mirror.)

●The battery has been disconnected. ●A door is open.

CAUTION

■While driving the vehicle

Do not adjust the display. Be sure to adjust the display only when the vehicle is stopped.

■When doing the circling calibration

Be sure to secure a wide space, and watch out for people and vehicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

413

3-7. Other interior features

NOTICE

■To avoid the compass malfunctions

Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause a malfunction of the compass sensor.

■To ensure normal operation of the compass

●Do not perform circling calibration of the compass in a place where the earth's magnetic field is subject to interference by artificial magnetic fields. ●During calibration, do not operate electric systems (moon roof, power win-

dows, etc.) as they may interfere with the calibration.

414

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition.

● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. Wash the vehicle body using a sponge or soft cloth, such as a chamois.

● For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

● Wipe away any water. ● Wax the vehicle when the waterproof coating deteriorates. If water does not bead on a clean surface, apply wax when the vehicle body is cool.

■Automatic car washes

●Before washing the vehicle, do the following.

• Fold the mirrors back. • Remove the antenna. (mast type only) • Turn the power back door system off.

●Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle’s paint.

■High pressure car washes

●Do not allow the nozzles of the car wash to come within close proximity

of the windows.

●Before car wash, check that the fuel filler door on your vehicle is closed

properly.

416

4-1. Maintenance and care

■Aluminum wheels

Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.

■Bumpers

Do not scrub with abrasive cleaners.

■To prevent deterioration and body corrosion

●Wash the vehicle immediately in the following cases:

• After driving near the sea coast • After driving on salted roads • If you see coal tar or tree sap on the paint surface • If you see dead insects or insect droppings on the paint • After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled in dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface

●If the paint is chipped or scratched, have it repaired immediately.

CAUTION

■Caution about the exhaust pipe

Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.

417

4-1. Maintenance and care

NOTICE

■To protect your vehicle’s painted surfaces

Do not use organic cleaners such as benzene or gasoline.

■If the windshield washer nozzle become blocked

Contact your Toyota dealer. Do not try to clear it with a pin or other object. This may damage the nozzle. ■Cleaning the exterior lights

●Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

●Do not apply wax on the surfaces of the lights.

Wax may cause damage to the lenses.

■To prevent damage to the windshield wiper arms

When lifting the wiper arms away from the windshield, pull the driver side wiper arm upward first, and repeat for the passenger side. When returning the wipers to their original position, do so from the passenger side first.

418

4-1. Maintenance and care Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle's interior and keep it in top condition: ■ Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.

■ Cleaning the leather areas

● Remove dirt and dust using a vacuum cleaner. ● Wipe any excess dirt and dust with a soft cloth dampened with

diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.

● Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

● Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded ventilated area.

■ Synthetic leather areas

● Remove loose dirt using a vacuum cleaner. ● Apply a mild soap solution to the synthetic leather. ● Allow the solution to soak in for a few minutes. Remove the

dirt and wipe off the solution with a clean, damp cloth.

419

4-1. Maintenance and care

■Cleaning the inside of the rear window or left-side rear quarter window Do not use glass cleaner to clean the rear window or left-side rear quarter window, as this may cause damage to the rear window defogger heater wires or print type antenna (if equipped). Use a cloth dampened with luke- warm water to gently wipe the windows clean. Wipe the windows in strokes running parallel to the heater wires or print type antenna (if equipped).

■Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior.

■Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. Excellent results are obtained by keeping the carpet as dry as possi- ble.

■Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.

CAUTION

■Water in the vehicle

●Do not splash or spill liquid in the vehicle.

Doing so may cause electrical components etc. to malfunction or catch fire.

●Do not get any of the SRS components or wiring in the vehicle interior wet.

(→P. 129) Electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or severe injury.

420

4-1. Maintenance and care

NOTICE

■Cleaning detergents

Do not use organic substances such as benzene or gasoline, acidic or alka- line solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces.

■Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of leather surfaces. ●Remove any dust or dirt on leather surfaces immediately. ●Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

●Do not place items made of vinyl, plastic, or that contain wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.

■Water on the floor

Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components under the floor of the vehicle, and may also cause the body to rust.

■Cleaning the inside of the rear window or left-side rear quarter window Be careful not to scratch or damage the heater wires or print type antenna (if equipped).

421

4-2. Maintenance Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance. ■ General maintenance

General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.

■ Scheduled maintenance

Scheduled maintenance should be performed at specified inter- vals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

■ Do-it-yourself maintenance

You can perform some maintenance procedures yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals is recommended. For details about warranty coverage, see the separate “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.

■Repair and replacement

It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.

422

4-2. Maintenance

■Allow inspection and repairs to be performed by a Toyota dealer

●Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.

●Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.

CAUTION

■Warning in handling of battery

●Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.

●Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.

●Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 449)

423

4-2. Maintenance General maintenance

Listed below are the general maintenance items that should be per- formed at the intervals specified in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.

Engine compartment

Items

Check points

Battery Brake fluid Engine coolant Engine oil Exhaust system

Radiator/condenser/hoses

Washer fluid

(→P. 449) Maintenance-free. (→P. 448) At the correct level? At the correct level? (→P. 445) At the correct level? (→P. 440) No fumes or strange sounds? Not blocked with foreign matter? (→P. 447) At the correct level? (→P. 452)

424

4-2. Maintenance

Vehicle interior

Items

Check points

Accelerator pedal

Automatic transmission “Park” mechanism

Brake pedal

Brakes

Head restraints

Indicators/buzzers

Lights

Parking brake

Seat belts

Seats

Steering wheel

• Moves smoothly (without uneven pedal effort or catching)? • Can the vehicle be held securely on an incline with the shift lever in P? • Moves smoothly? • Does it have appropriate clear- ance and correct amount of free play? • Not pull to one side when applied? • Loss of brake effectiveness? • Spongy feeling brake pedal? • Pedal almost touches floor? • Move smoothly and lock securely? • Function properly? • Do all the lights come on? • Headlights aimed correctly? • Moves smoothly? • Can hold the vehicle securely on an incline? • Does the seat belt system oper- ate smoothly? • Are the belts undamaged? • Do the seat controls operate properly? • Moves smoothly? • Has correct free play? • No strange noises?

425

4-2. Maintenance

Vehicle exterior

Door Engine hood

Fluid leaks

Tire

Items

Check points

• Operate smoothly? • The lock system works properly? • Is there any leakage after park- ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? • Tires rotated according to the maintenance schedule? • Wheel nuts are not loose?

CAUTION

■If the engine is running

Turn the engine off and ensure that there is adequate ventilation before per- forming maintenance checks.

426

4-2. Maintenance Emission inspection and maintenance (I/M) programs

Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. ■ If the malfunction indicator lamp comes on

The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.

■ Your vehicle may not pass the I/M test:

● When the battery is disconnected or discharged

Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.

● When the fuel tank cap is loose

The malfunction indicator lamp comes on as a temporary mal- function and your vehicle may not pass the I/M test.

■ When the malfunction indicator lamp goes off after several

driving trips The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.

■ If your vehicle does not pass the I/M test

Contact your Toyota dealer to prepare the vehicle for re-testing.

427

4-3. Do-it-yourself maintenance Do-it-yourself service precautions

If you perform maintenance yourself, be sure to follow the correct procedures as given in these sections.

Items

Parts and tools

• Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology. For the U.S.A.: “Toyota Super Long Life Coolant” is pre-mixed with 50% coolant and 50% deionized water. For Canada: “Toyota Super Long Life Coolant” is pre-mixed with 55% coolant and 45% deionized water. • Funnel (used only for adding engine coolant) • “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel, funnel (used only for adding oil)

Battery condition

(→P. 449)

Brake fluid level

(→P. 448)

Engine coolant level

(→P. 445)

Engine oil level

(→P. 440)

428

4-3. Do-it-yourself maintenance

Items

Parts and tools

Fuses

(→P. 475)

• Fuse with same amperage rating as original

Radiator and condenser

(→P. 447)

Tire inflation pressure (→P. 463)

Washer fluid

(→P. 452)

⎯

• Tire pressure gauge • Compressed air source • Water washer fluid containing antifreeze (for winter use) • Funnel

429