’05 HIGHLANDER_U (L/O 0409)
SECTION 1− 1
OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview Instrument cluster overview Indicator symbols on the instrument panel
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
11
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Instrument panel overview "Vehicles with rear seat entertainment system (view A)
1. Side defroster outlets 2. Instrument cluster 3. Center vents 4. Electric moon roof switch and personal
lights
5. Garage door opener 6. Auxiliary boxes 7. Side vents 8. Power door lock switches 9. Power window switches 10. Glove box 11. Automatic transmission selector lever 12. Rear ashtray 13. Input terminal adapter 14. Power outlets 15. Cup holder 16. Container 17. Front ashtray 18. Audio remote control switches 19. Hood lock release lever 20. Parking brake pedal 21. Window lock switch
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
"Vehicles without rear seat entertainment system (view A)
1. Side defroster outlets 2. Instrument cluster 3. Center vents 4. Electric moon roof switch and personal
lights
5. Garage door opener 6. Auxiliary boxes 7. Side vents 8. Power door lock switches 9. Power window switches 10. Glove box 11. Automatic transmission selector lever 12. Rear ashtray 13. Cup holder 14. Container 15. Power outlet 16. Front ashtray 17. Audio remote control switches 18. Hood lock release lever 19. Parking brake pedal 20. Window lock switch
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
"Vehicles with manual air conditioning controls (view B)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches 3. Emergency flasher switch 4. Clock 5. Front passenger’s seat belt reminder
light
6. Rear window and outside rear view
mirror defogger and windshield wiper de−icer switch
7. Air conditioning controls 8. Audio system 9. “AIRBAG ON” and “AIRBAG OFF”
indicator lights
10. Snow mode button 11. Seat heater switches 12. Cigarette lighter 13. “TRAC OFF” switch
(two−wheel drive models)
14. Cruise control switch 15. Ignition switch 16. Tilt steering lock release lever 17. Tire pressure warning system reset
switch
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
18. Power outlet (115 VAC) main switch 19. Rear heater main switch 20. Theft deterrent system/engine
immobilizer system indicator light
21. Power rear view mirror control switches
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
"Vehicles with automatic air conditioning controls (view B without navigation system)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches 3. Emergency flasher switch 4. Clock 5. Front passenger’s seat belt reminder
light
6. Air conditioning controls and
multi−information display
7. Rear window and outside rear view
mirror defogger and windshield wiper de−icer switch 8. Audio system 9. “AIRBAG ON” and “AIRBAG OFF”
indicator lights
10. Snow mode button 11. Seat heater switches 12. Cigarette lighter 13. “TRAC OFF” switch
(two−wheel drive models)
14. Cruise control switch 15. Ignition switch 16. Tilt steering lock release lever 17. Tire pressure warning system reset
switch
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
18. Power outlet (115 VAC) main switch 19. Rear heater main switch 20. Theft deterrent system/engine
immobilizer system indicator light
21. Power rear view mirror control switches
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
"Vehicles with automatic air conditioning controls (view B with navigation system)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches 3. Emergency flasher switch 4. Clock (See the separate “Navigation
System Owner’s Manual”.)
5. Front passenger’s seat belt reminder
light
6. Navigation system including air
conditioning controls (See the separate “Navigation System Owner’s Manual”.)
7. Rear window and outside rear view
mirror defogger switch
8. Audio system (See the separate
“Navigation System Owner’s Manual”.)
9. “AIRBAG ON” and “AIRBAG OFF”
indicator lights
10. Snow mode button 11. Seat heater switches 12. Cigarette lighter 13. “TRAC OFF” switch
(two−wheel drive models)
14. Cruise control switch 15. Ignition switch 16. Tilt steering lock release lever
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
17. Tire pressure warning system reset
switch
18. Power outlet (115 VAC) main switch 19. Rear heater main switch 20. Theft deterrent system/engine
immobilizer system indicator light
21. Power rear view mirror control switches
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Instrument cluster overview
1. Tachometer 2. Service reminder indicators and
indicator lights
3. Speedometer
4. Fuel gauge 5. Low fuel level warning light 6. Engine coolant temperature gauge
7. Trip meter reset knob 8. Odometer and two trip meters 9. Instrument panel light control knob
10
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Indicator symbols on the instrument panel
or
Brake system warning light∗1
or
Anti−lock brake system warning light∗1
Driver’s seat belt reminder light∗1
Open door warning light∗1
Front passenger’s seat belt reminder light∗1
Automatic transmission fluid temperature warning light∗1 (four−wheel drive models)
Discharge warning light∗1
SRS warning light∗1
Low engine oil pressure warning light∗1
Vehicle stability control system warning light∗1
or
Malfunction indicator lamp∗1
Low tire pressure warning light∗1
Low windshield washer
light∗1
fluid
level warning
11
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Engine oil replacement reminder light∗1 (for vehicles sold in U.S.A.)
Snow mode indicator light
“AIRBAG ON” indicator light
Slip indicator light
“AIRBAG OFF” indicator light
Traction control system off indicator light
Headlight high beam indicator light
Cruise control indicator light∗2
Turn signal indicator lights
or
Automatic transmission indicator lights
Overdrive−off indicator light
12
∗1: For details, see “Service reminder indicators and warning
∗2:
buzzers” on page 135 in Section 1−6. If this light flashes, see “Cruise control” on page 165 in Section 1−7.
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
SECTION 1− 10
OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Multi−information display Clock Compass Cigarette lighter and ashtrays Power outlets Power outlet Glove box Garage door opener Auxiliary boxes Container Cup holders Bottle holders Tie−down hooks Luggage cover Roof luggage carrier Floor mat
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
266
267
268
272
273
274
275
275
278
280
281
283
283
284
286
288
information about the clock of a vehicle equipped with the separate “Navigation
For Navigation system, please refer System Owner’s Manual”.
to
265
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Multi−information display
Air conditioning system on—
Air conditioning system off—
266
The multi−information display indicates the following information. 1. Outside temperature 2. Average vehicle speed 3. Average fuel consumption 4. Instantaneous fuel consumption 5. Driving time 6. Air conditioning system on—The air
conditioned temperature is displayed. Air conditioning system off—The air conditioned is not dis- played.
temperature
Every time you push the “INFO” button, the display toggles through this informa- tion. The displayed values in the multi−informa- tion display indicate general driving condi- tions. Accuracy varies with driving habits and road conditions. You can adjust the air conditioned temper- ature while the multi−information is operat- ing. 5 seconds has been passed after ad- justing the “INFO” button, the display will be back to the multi−information display.
temperature or pushing
the
1. Outside temperature
(“OUTSIDE TEMP”)
from
indi-
temperature
the outside air
The outside temperature display cates the outside air temperature. The displayed ranges −22_F (−30_C) up to 122_F (50_C). If an abnormality exists in the connection of temperature sensor, “−−_F” (“−−_C”) will appear on the display. If “−−_F” (“−−_C”) appears on the display, contact your Toyota dealer. There may be a case that “−−_F” (“−−_C”) appears momentarily when the ignition is quickly turned to “ON”. It is normal if it goes out soon. 2. Average vehicle speed
(“AVG MPH” or “AVG km/h”)
Average vehicle speed is calculated and
displayed based on total driving dis-
tance and total driving time with the
engine running.
The displayed value is updated every 10
seconds.
To reset the calculation, push the “INFO”
button for more than 1 second.
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
3. Average fuel consumption
(“AVG MPG” or “AVG L/100 km”)
total
Average fuel consumption is calculated
and displayed based on total driving
distance and
fuel consumption
with the engine running.
The displayed value is updated every 10
seconds.
4. Instantaneous fuel consumption
(“MPG” or “L/100 km”)
The instantaneous fuel consumption is
calculated and displayed based on dis-
tance and fuel consumption for 1 sec-
onds with the engine running.
The displayed value is updated every 2
seconds.
Note that an accurate figure may not be
shown in the following cases.
D The vehicle is stopped with the engine
running. (The display will indicate the
extremely high fuel consumption.)
is driving down a
long slope applying the engine brake. (The display will indicate the extremely low fuel consumption.)
D The vehicle
The calculation is reset when the ignition switch is turned off.
’05 HIGHLANDER_U (L/O 0409)
Clock
5. Driving time (“E/T”)
The elapsed time after the engine starts
is displayed.
When the engine is started, driving time
is counted from 0:00. Up to 11:59 (11
hours, 59 minutes) can be displayed.
When the driving time exceeds 11:59, the
counter returns to 0:00.
The calculation is reset when the ignition
switch is turned off.
To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. The key must be in the “ACC” or “ON” position. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock).
267
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
Compass
The direction is indicated on the inside rear view mirror. If the ignition switch was turned off with the system on, the system will automati- cally turn back on when the ignition switch is turned on. Push the “COMP” switch to turn the com- pass system on and off.
268
’05 HIGHLANDER_U (L/O 0409)
indicates
the vehicle
the direction The compass that the above case, it shows that the vehicle is heading north.
is heading.
In
Displays
NE SE SW NW
Directions
North
Northeast
East
Southeast
South
Southwest
West
Northwest
The compass may not show the correct direction in the following conditions: D The vehicle is stopped immediately af-
ter turning.
D The compass does not adjust while the
vehicle is stopped.
D The ignition switch is turned off imme-
diately after turning.
D The vehicle is on an inclined surface.
D The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).
D The vehicle is magnetized. (There is a magnet or a metal object on or near the inside rear view mirror.)
the deviation
D The battery has been disconnected. If your vehicle is out of the set zone, refer to “CALIBRATING THE COMPASS” below to set the zone number. If the compass works to calibrate the direction automati- cally while the vehicle is in motion. For additional precision or calibrating, see COMPASS” below.
for complete THE
“CALIBRATING
is small,
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Compass sensor
The compass sensor is in the inside rear view mirror.
NOTICE
Do not put magnets or a metal object on or near the inside rear view mirror of the vehicle. Doing this may cause malfunction of the compass sensor.
the
from
CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on true direction deter- deviates mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust this deviation, stop the vehicle, then push and hold the “COMP” switch until the zone number appears on the dis- play. Then push the “COMP” switch, refer- ring to the following map to select the number of the zone where the vehicle is.
269
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Samoa: 5
Guam:
Saipan: 8
After calibration, leaving the system for several seconds returns it to the compass mode.
CAUTION
Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.
Zone number
270
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the battery has been removed, re- placed or disconnected. D Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).
in a place where
D During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.
the direction display on
CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. To rectify this, stop the vehicle and push and hold the “COMP” switch until “C” appears on the display. If “C” appears on the display because of a drastic change in the magnetic field, perform circling calibration.
in a circle, drive around
Drive the vehicle in a circle at 8 km/h (5
mph) or less. If there is not enough space
to drive
the
block.
After driving 1 to 3 circles in the above
method, calibration is completed when the
direction is shown on the display.
If calibration cannot be performed because
of the magnetized vehicle etc., take your
vehicle to Toyota dealer.
271
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Cigarette lighter and ashtrays
CAUTION
D When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.
D Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.
Cigarette lighter
Rear ashtray
272
Front ashtray
CIGARETTE LIGHTER To use the cigarette lighter, press it in. After it finishes heating up, it automati- cally pops out ready for use. If the engine is not running, the key must be in the “ACC” position. Do not hold the cigarette lighter pressed in. Use a Toyota genuine cigarette lighter or equivalent for replacement.
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Power outlets (12 VDC)
ASHTRAYS Front ashtray: To use the ashtray, open the lid. When finished with your cigarette, thor- oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, close the lid completely. To remove the ashtray, pull the lid and pull it out. Rear ashtray: To use the ashtray, pull it out. When finished with your cigarette, thor- oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, close the lid completely. To remove the ashtray, press down on the lock spring plate and pull out.
CAUTION
To reduce the chance of in case of an accident or sudden stop while driving, always completely close the ashtray after use.
injury
Front
Rear
The power outlets (12 VDC) are de- signed for power supply for car acces- sories. The key must be in the “ACC” or “ON” position for the power outlets to be used.
NOTICE
the
z To prevent
fuse
from being blown, do not use the electricity over the total vehicle capacity of 12VDC/120W (front and rear outlets together).
z To prevent the battery from being discharged, do not use the power outlets longer than necessary when the engine is not running.
z Close the power outlet
lids when the power outlets are not in use. Inserting a foreign object other than the appropriate plug that fits the outlet, or allowing any liquid into the outlet may cause electrical fail- ure or short circuits.
273
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Power outlet (115 VAC)
NOTICE
z To prevent the battery from being discharged, do not use the power outlet longer than necessary when the engine is not running.
z Close the power outlet lid when the power outlet is not in use. Inserting anything other than an appropriate plug that fits the outlet may cause electrical failure or short circuits.
The power outlet is not designed for the following electric appliances even though their power consumption is un- der 115 VAC/100W. These appliances may not operate properly.
This power outlet (115 VAC) is designed for use as a power supply for electric appliances in the vehicle. The key must be in the “ON” position for the power outlet to be used. The maximum capacity for this power out- let is 115 VAC/100W. If you attempt to use an appliance that requires more than 115 VAC or 100W, the protection circuit will activate and cut the power supply. The power supply will restart automatically when you use an appliance that operates within the 115 VAC/100W limits.
Main switch
To use the power outlet, push the main switch on the instrument panel. An indicator light will illuminate to indicate that the power outlet is ready for use. Push the main switch once again to turn the power outlet off. When the power out- let is not in use, make sure that the main switch is turned off.
274
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
D Appliances with high initial peak watt- age: cathode−ray tube type televisions, compressor−driven refrigerators, electric pumps, electric tools, etc.
D Measuring devices which process pre- cise data: medical equipment, measur- ing instruments, etc.
D Other appliances requiring an extremely stable power supply: microcomputer− controlled electric blankets, touch sen- sor lamps, etc.
Certain electrical appliances may cause radio noise.
’05 HIGHLANDER_U (L/O 0409)
Glove box
Garage door opener
The garage door opener ( Universal Transceiver) is manufactured under license from HomeLinkR and can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, etc.
To use the glove box, do this. To open: Pull the lever. With the instrument panel lights on, the glove box light will come on when the globe box is open. To lock: Insert the master key and turn it clockwise.
CAUTION
To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.
injury
275
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
transmitter prior
(a) Programming the HomeLinkR
The HomeLinkR in your vehicle has 3
buttons and you can store one program
for each button.
To ensure correct programming into the
HomeLinkR, install a new battery in the
hand−held
to program-
ming.
The battery side of the hand−held trans-
mitter must be pointed away
the
HomeLinkR during the programming pro-
cess.
For Canadian users, follow the procedure
“Programming an entrance gate/pro-
in
gramming all devices
the Canadian
market”.
1. Decide which of 3 HomeLinkR buttons
from
in
you want to program.
2. Place your hand−held garage transmit- ter 25 to 75 mm (1 to 3 in.) away from the surface of the HomeLinkR.
Keep the indicator light on the HomeLinkR in view while programming.
276
3. Simultaneously press and hold
the hand−held garage transmitter button along with the selected HomeLinkR but- ton.
4. When
the
indicator
the HomeLinkR changes from a slow to a rapid flash after 20 seconds, you can release both buttons.
light on
5. Test the operation of the HomeLinkR by pressing the newly programmed button. If programming a garage door opener, check to see if the garage door opens and closes.
(on
light
indicator
If the garage door does not operate, iden- tify if your garage transmitter is of the “Rolling Code” type. Press and hold the programmed HomeLinkR button. The ga- rage door has the rolling code feature if the HomeLinkR) the flashes rapidly and then remains lit after 2 seconds. If your garage transmitter is the “Rolling Code” type, proceed to the heading “Programming a rolling code sys- tem”. 6. Repeat steps 2 through 5 for each re- maining HomeLinkR button to program another device.
it
is
to
is necessary
Programming a rolling code system “Rolling Code” If your device follow equipped, steps 1 through 4 under the heading “Programming the HomeLinkR” before proceeding with the steps listed below. 1. Locate the “training” button on the ceil- ing mounted garage door opener motor. The exact the button may vary by brand of garage door opener. Refer the owner’s guide supplied by the garage door opener manufacturer for the location of this “training” button.
location and color of
to
2. Press the “training” button on the ceil- ing mounted garage door opener motor. Following this step, you have 30 seconds in which to initiate step 3 below. 3. Press and release the vehicle’s pro- grammed HomeLinkR button twice. The garage door may open. the door does open, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door.
If
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
(c) Erasing
the
entire HomeLinkR
memory (all three programs)
To erase all previously programmed codes
at one time, press and hold down the 2
outside buttons for 20 seconds until the
indicator light flashes.
If you sell your vehicle, be sure to erase
the HomeLinkR
the programs stored
memory.
in
now
should
recognize
The ceiling mounted garage door opener motor the HomeLinkR unit and be able activate the garage door up/down. 4. Repeat steps 1 through 3 for each re- maining HomeLinkR button to program another rolling code system.
Programming an entrance gate/program- ming all devices in the Canadian market 1. Decide which of the 3 HomeLinkR but-
2. Place
your
tons you want to program. hand−held
gate/device transmitter 25 to 75 mm (1 to 3 in.) away the from HomeLinkR.
surface
the
of
Keep the indicator light on the HomeLinkR in view while programming. 3. Press
selected
hold
and
the
HomeLinkR button.
4. Continuously press and release (cycle)
transmitter
the hand−held gate/device
button every two seconds until step 5
is complete.
the
the HomeLinkR changes from a slow to a rapid flash after 20 seconds, you can release both buttons.
light on
5. When
indicator
6. Test the operation of the HomeLinkR by pressing the newly programmed button. Check to see if the gate/device oper- ates correctly.
7. Repeat steps 1 through 6 for each re- maining HomeLinkR button to program another device.
Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button Individual HomeLinkR buttons cannot be erased, however, to reprogram a single button, follow the procedure “Programming the HomeLinkR”. (b) Operating the HomeLinkR To operate the appropriate HomeLinkR button to activate the programmed device. The HomeLinkR indicator light should come on. The HomeLinkR continues to send the signal for up the button is pressed.
the HomeLinkR, press
to 20 seconds as
long as
277
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
CAUTION
D When programming the HomeLinkR Universal Transceiver, you may be operating a garage door or other device. Make sure people and ob- jects are out of the way of the ga- rage door or other device to pre- vent potential harm or damage.
D Do not use this HomeLinkR Univer- sal Transceiver with any garage door opener that lacks the safety stop and reverse feature as re- quired by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door open- er which cannot detect an object (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death.
278
’05 HIGHLANDER_U (L/O 0409)
received,
This device complies with Part 15 of the FCC Rules and with RSS−210 of the IC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party re- sponsible for compliance could void the user’s authority to operate the device.
including
Auxiliary boxes To use the auxiliary boxes, open the lids as shown in the following illustra- tions.
CAUTION
D To reduce the chance of injury in case of an accident or sudden stop, always keep the auxiliary box closed while driving.
D Type A—It is designed for holding a light objects, do not place any heavy objects in it. Heavy objects may cause the holder to open and contents to fly out resulting in inju- ries.
NOTICE
Type A—During hot weather, the inte- rior of the vehicle becomes very hot. Do not leave anything flammable or deformable such as a lighter, glasses, etc. inside.
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Type A (ceiling)
Type C (rear console)
Type E (luggage compartment)
Type B (instrument panel)
Type D (rear console)
279
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Container
This container can be used as an auxil- iary holder.
CAUTION
Do not put objects in the container which can shift, roll out or be thrown out in the event of sudden stops or accidents. Objects which come out of the container can create a safety haz- ard due to interference with pedal op- eration or driver distraction. D Do not store drinks or cans which
could easily roll out.
Type F (luggage compartment)
280
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Cup holders
D Do not store objects which are higher than the lower edge of the container.
D Do not store objects which are larg- er than the width of the container.
Type A (rear console)
Type B (luggage compartment)
Type C (second seat armrest)
281
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
The cup holders are designed for hold- ing cups or drink−cans securely. Type A—To use the holder, open the lid. Type C—To use the holder, pull down the second seat armrest and push the button on the armrest.
CAUTION
D Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.
reduce
D Type A and C—To
the chance of injury in case of an acci- dent or sudden stop while driving, keep the cup holder closed when it is not in use.
Type A only— The cup holder can be adjustable to the size of the cups or drink−cans by changing the holder position.
282
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Bottle holders
Tie−down hooks
NOTICE
Do not put a cup or open bottle in the bottle holder because the con- tents may spill when the door opens or closes.
The bottle holders are designed to hold bottles securely.
CAUTION
Do not attempt to use the holder for any other purpose for which it was intended. Inappropriately sized or shaped objects may be thrown about in the compartment and possibly in- jure people in the vehicle during a sudden braking or an accident.
To secure your luggage, use the tie−down
hooks as shown above.
See “—Stowage precautions” on page 313
in Section 2 for precautions when loading
luggage.
CAUTION
To avoid personal injury, keep the tie− down hooks folded in place on the floor when not in use.
Vehicles with the third seat—When using the tie−down hooks, the third seat must be “—Folding down third seat” on page 51 in Section 1−3.)
folded down.
(See
283
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
Luggage cover
NOTICE
Do not use the anchor brackets on the second seat seatback instead of the tie−down hooks.
’05 HIGHLANDER_U (L/O 0409)
USING LUGGAGE COVER To use the luggage cover: 1. Pull out the forward luggage cover and hang the hooks to the hook brackets on the second seat seat- back.
2. Pull out the rear luggage cover and
secure it to the hook brackets.
CAUTION
Do not place anything on the luggage cover. Such thrown about and possibly injure people in the vehicle during sudden braking or a collision.
items may be
Vehicles with the third seat—When using the luggage cover, the third seat must be folded down. (See “—Folding down third seat” on page 51 in Section 1−3.)
284
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
REMOVING LUGGAGE COVER To remove the luggage cover, push in the left end to release the right end, and lift the luggage cover out. After you remove the luggage cover, stow it under deck board as described below. This will prevent passengers from injury in the event of a sudden stop or accident.
STOWING LUGGAGE COVER To stow the luggage cover, do the fol- lowing. 1. Remove the side deck boards and
open the center deck board.
285
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
2. Push in the left end of the luggage cover and place the luggage cover in the holder as shown.
CAUTION
Make sure the luggage cover is se- curely stowed.
Roof luggage carrier
Cross rails
Side knobs
Upper knob
Roof rails
The roof roof rails and sliding cross rails.
luggage carrier consists of
ADJUSTING THE POSITION OF CROSS RAILS: 1. Turn the upper and side knobs coun- the cross
loosen
to
terclockwise rails.
286
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Follow the manufacture’s instructions and precautions when the attach- ments or their equivalent.
installing
CAUTION
When you load cargo on the roof lug- gage carrier, observe the following: D Place the cargo so that its weight is distributed evenly between the front and rear axles.
2. Slide the cross rails to the appropri- ate position for loading the luggages and turn the side knobs clockwise to tighten the cross rails securely.
3. In order to fix the cross rails to the appropriate the upper knobs clockwise after tightening all of the side knobs.
length, turn
the
with
Vehicles electric moon roof—There are cross rail stoppers on the roof the cross rails being touched with the tilted up moon roof.
rails which help you prevent
NOTICE
Vehicles with the electric moon roof only—Do not remove the cross rail stoppers, or the moon roof may be damaged when it is tilted.
CAUTION
them. Failure
Make sure the cross rails are fixed securely by pushing forward and rear- ward to do so may cause an unexpected accident or se- vere injury in the event of emergency braking or a collision.
D If loading long or wide cargo, never
exceed the vehicle overall length or
width.
and
weights” on page 406 in Section 8
for
information on your vehicle
overall length and width.)
“Dimensions
(See
D Before driving, make sure the cargo the roof
fastened on
is securely luggage carrier.
D Loading cargo on the roof luggage carrier will make the center of the vehicle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneu- vers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle cor- rectly.
287
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Floor mat
D If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then dur- ing the trip to make sure the cargo remains in its place.
D Do not exceed 45 kg (100 lb.) cargo weight on the roof luggage carrier.
NOTICE
When loading the luggages, be careful not the moon roof.
the surface of
to scratch
Use a floor mat of the correct size.
If the floor carpet and floor mat have 2
holes, then they are designed for use with
locking clips. Fix the floor mat with lock-
ing clips into the holes in the floor carpet.
CAUTION
Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and the movement of the pedals during driv- ing, it may cause an accident.
interferes with
288
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
SECTION 1− 2
OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys Engine immobilizer system Wireless remote control Side doors Power windows Back door Hood Theft deterrent system Fuel tank cap Electric moon roof
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
17
18
24
27
30
31
32
34
36
13
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Keys (without engine immobilizer system)
Keys (with engine immobilizer system)
KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.
Your vehicle is supplied with two kinds of keys. 1. Master keys (black)—These keys work in every lock. Your Toyota dealer will need one of them to make a new key with a built−in transponder chip.
2. Sub key (gray)—This key will not work
in the glove box.
Your vehicle is supplied with two kinds of keys. 1. Master keys—These keys work in ev-
ery lock.
2. Sub key—This key will not work in the
glove box.
To protect items locked in the glove box when using valet parking, leave the sub key with the attendant. Since the side doors can be locked with- out a key, you should always carry a spare key in case you accidentally lock your keys inside the vehicle.
14
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
A transponder chip for engine immobilizer system has been placed in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine. To protect items locked in the glove box when using valet parking, leave the sub key with the attendant. Since the side doors can be locked with- out a key, you should always carry a spare key in case you accidentally lock your keys inside the vehicle.
’05 HIGHLANDER_U (L/O 0409)
NOTICE
the
When using a key containing a trans- ponder chip, observe following precautions: z When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.
z When starting the engine, do not use the key with other transponder keys around (including keys of oth- er vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after remov- ing other transponder keys (includ- ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.
15
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
z Do not cover the key grip with any material that cuts off electromagnet- ic waves.
z Do not knock the key hard against
other objects.
z Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under direct sunlight. z Do not put the key
in water or
wash it in an ultrasonic washer.
z Do not bend the key grip.
z Do not use the key with electromag-
netic materials.
KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.
16
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
Engine immobilizer system
For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you. If you make your own duplicate key, you will not be able to cancel the sys- tem or start the engine.
NOTICE
Do not modify, remove or disas- semble the engine immobilizer sys- tem. If any unauthorized changes or modifications are made, proper opera- tion of the system cannot be guaran- teed.
immobilizer system
The engine is a theft prevention system. When you in- sert the key in the ignition switch, the transponder chip the key’s head transmits an electronic code to the ve- hicle. The engine will start only when the electronic code in the chip corre- sponds to the registered ID code for the vehicle.
in
indicator
light will start
The system is automatically set when the key is removed from the ignition switch. The flashing to show the system is set. In the following cases, contact your Toyota dealer. D The indicator light stays on. D The indicator light does not start flash- ing when the key is removed from the ignition switch.
D The indicator light flashes inconsistent-
ly.
Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off.
17
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
For vehicles sold in U.S.A.
For vehicles sold in Canada
Wireless remote control—
FCC ID: MOZRI−20BTY MADE IN JAPAN This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.
CAUTION
Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
18
This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.
interference,
including
1. “LOCK” switch 2. “UNLOCK” switch 3. “PANIC” switch
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
The wireless remote control system is designed to lock or unlock all the side doors and back door, or activate the “PANIC” mode from a distance within approximately 1 m (3 ft.) of the vehicle. When you operate any switch, push it slowly and securely. The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause damage to the transmitter. D Do not leave the transmitter in places the temperature becomes high
where such as on the dashboard.
D Do not disassemble it. D Avoid knocking
it hard against other
objects or dropping it.
D Avoid putting it in water. You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information.
transmitters
for
’05 HIGHLANDER_U (L/O 0409)
If the wireless remote control transmitter does not actuate the side doors and back door or alarm, or operate from a normal distance: D Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.
D The battery may have been consumed. Check the battery in the transmitter. To replace the battery, see “—Replacing transmitter battery” on page 22.
If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an acci- dent. (See “If you lose your wireless re- mote control transmitter” on page 355 in Section 4.) For vehicles sold in U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.
interference
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interfer- ence by one or more of the following measures:
to radio or
19
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
—Locking and unlocking doors
D Reorient or relocate the receiving an-
tenna.
D Increase the separation between the
equipment and receiver.
D Connect the equipment into an outlet to
on a circuit different which the receiver is connected.
from
that
D Consult the dealer or an experienced
radio/TV technician for help.
FCC WARNING: Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
For vehicles sold in Canada
Locking operation
Operation is subject to the following two conditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.
interference,
including
20
Unlocking operation
To lock and unlock all the side doors and back door, push the switches of the transmitter slowly and securely. To lock: Push the “LOCK” switch. All the side doors and back door are locked si- multaneously. At this time, one beep will be heard, and the turn signal lights flash once. Check to see that all the side doors and back door are securely locked. If any of the side doors or back door is not securely closed, locking cannot be performed by the “LOCK” switch and a beep will sound continuously for 10 sec- onds. However, if the key is in the igni- tion, a beep will not sound. To stop the beep, close all the side doors and back door securely or push the “UNLOCK” switch. The beep can be disabled. For details, contact your Toyota dealer. “UNLOCK” switch To unlock: Push once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the turn signal lights flash twice.
the
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
This double switch operation to unlock all the side doors and back door can be changed to a single switch operation. For details, contact your Toyota dealer. When all the side doors and back door are unlocked simultaneously with a wire- less remote control transmitter, the center interior light, personal lights and ignition switch light come on for about 15 seconds before fading out, even if the door is not opened. (For details, see “Interior lights” on page 124, “Personal lights” on page 125 and “Ignition switch light” on page 126 in Section 1−5.) You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will be automati- cally locked again. At this time, one beep will be heard, and the turn signal lights flash once. lock The timing function can be changed. For details, con- tact your Toyota dealer. If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera- tion is not repeated. Release the switch and then push again.
the automatic door
for
’05 HIGHLANDER_U (L/O 0409)
The wireless door locking or unlocking function can be erased. For details, con- tact your Toyota dealer.
—Switching beep sound You can switch the beep on and off. (The beep is on initially and after battery re- placement.) To switch the beep on and off: With the driver’s door opened— 1. Insert the ignition key and remove it. 2. Within 5 seconds,
ignition key again and turn it to the “ON” posi- tion.
insert
the
3. After 10 seconds, push
the same “LOCK”, “UNLOCK” or “PANIC” switch twice within 10 seconds. Two beep sounds inform you that the program has been switched on or off. If this procedure is not followed exactly, the beep will not operate as expected. Check the beep on/off operation by push- ing the transmitter switch after you finish this procedure. If the beep does not oper- ate as expected, repeat this procedure from step 1.
21
2005 HIGHLANDER from Nov. ’04 Prod. (OM48570U)
’05 HIGHLANDER_U (L/O 0409)
—Activating panic mode
The “PANIC” mode does not work when the ignition key is in the “ON” position. The alarm function can be disabled. For details, contact your Toyota dealer.
flashes
to break
Pushing the “PANIC” switch blows the horn intermittently and the headlights and tail lights. The “PANIC” switch is used to deter ve- hicle theft when you witness anyone at- tempting into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, do the following: D Push the “PANIC” switch once again. D Unlock any of side door or back door with the key or wireless remote control transmitter.
—Replacing transmitter battery For replacement, use a CR2016 lithium battery or equivalent.
CAUTION
Special care should be taken to pre- vent small children from swallowing the removed transmitter battery or components.
NOTICE
z When replacing the transmitter bat- tery, be careful not to lose the com- ponents.
z Replace only with
the same or equivalent type recommended by a Toyota dealer.
z Dispose of used batteries according
to the local laws.
Replace the transmitter battery by follow- ing these procedures:
D Turn the ignition key from the “LOCK”
to “ON” position.