Download PDF Manual

(airbag and inflator)


7. SRS warning light The airbag sensor assembly consists of a safing sensor and airbag sensor.


42


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


the windshield as


A crash severe enough to inflate the air- bags may break the vehicle buckles. In vehicles with a pas- senger airbag the windshield may also be damaged by absorbing some of the force of the inflating airbag.


CAUTION


D The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver side and front passenger side seat belt sys- tems. The front seat occupants can be killed or seriously injured by the inflating airbags if they do not wear the available seat belts properly. During sudden braking just before a collision, an unrestrained driver or front passenger can move for- ward into direct contact with or close proximity to the airbag which may then deploy during the colli- sion. To ensure maximum protection in an accident, the driver and all passengers the vehicle must wear their seat belts properly. Wear- ing a seat belt properly during an accident reduces the chances of death or serious injury or being thrown out of the vehicle. For in- structions and precautions concern- ing the seat belt system, see “Seat belts” on page 32 in this section.


in


restraint


D Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing front airbags. An infant or child who is too small to use a seat belt should be properly secured using a child Toyota strongly recommends in- fants and children be placed in the rear seat of the vehicle and proper- ly restrained. The rear seat is the safest for infants and children. For instructions concerning the installa- tion of a child restraint system, see “Child restraint” on page 53 in this section.


that all


system.


2003 MY COROLLA_U (OM12744U)


43


’03 Corolla U (L/O 0201)


D On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbags inflate, because impact could cause death or serious injury to the child. the installation of a child restraint sys- tem, see “Child restraint” on page 53 in this section.


instructions concerning


D For


the


D Never install a rear−facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.


Move seat fully back


the


D A forward−facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible, because the force of the deploying front passenger air- bag could cause death or serious injury to the child.


44


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


the


D Do not allow a child to stand up or to kneel on front passenger seat, since the front airbag inflates with considerable speed and force. Otherwise, the child may be killed or seriously injured.


D Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” on page 53 in this sec- tion.


D Do not put objects or your pets on or in front of the dashboard or steering wheel pad that houses the front airbag system. They might re- strict inflation or cause death or serious injury as they are projected rearward by the force of deploying airbags. Likewise, the driver and front passenger should not hold ob- jects their knees.


their arms or on


in


2003 MY COROLLA_U (OM12744U)


45


is


in use, since


D Do not sit on the edge of the seat lean over the dashboard when or the vehicle the front airbags inflate with consider- able speed and force. Otherwise, you may be killed or seriously in- jured. Sit up straight and well back in the seat, and always use your seat belt properly.


D Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, front passen- ger airbag cover, front passenger airbag or airbag sensor assembly. Doing so may cause sudden SRS front airbag inflation or disable the system, which could result in death or serious injury.


instructions Failure to follow these can result in death or serious injury. Consult your Toyota dealer about any repairs and modifications.


’03 Corolla U (L/O 0201)


NOTICE


consulting


front airbag system


Do not perform any of the following changes without your Toyota dealer. Such changes can interfere with proper operation of the SRS in some cases. z Installation of electronic devices such as a mobile two−way radio, cassette tape player or compact disc player


z Modification of the suspension sys-


tem


z Modification of the front end struc-


ture


z Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end


z Repairs made on or near the front fenders, front end structure, con- sole, steering wheel or dashboard near the front passenger airbag


steering


column,


This SRS front airbag system has a ser- vice reminder indicator to inform the driver of operating problems. If either of the fol- lowing conditions occurs, this indicates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to ser- vice the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or the light remains on.


D The light comes on while driving.


46


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


SRS side airbags


NOTICE


Do not disconnect the battery cables before contacting your Toyota dealer.


The SRS (Supplemental Restraint Sys- tem) side airbags are designed to pro- vide further protection for the driver and front passenger in addition to the primary safety protection provided by the seat belts. In response to a severe side impact, the SRS side airbags work together with the seat belts to help reduce injury by inflat- ing. The SRS side airbags help to reduce injuries mainly to the driver’s or front pas- senger’s chest. The SRS side airbag on the passenger seat is activated even with no passenger in the front seat. Be sure to wear your seat belt properly.


2003 MY COROLLA_U (OM12744U)


47


In the following cases, contact your Toyota dealer as soon as possible: D The SRS front airbags have been in-


flated.


D The front of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS front airbags to inflate.


D The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.


passenger


airbag


front


’03 Corolla U (L/O 0201)


Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seat belt restraint system by the driver and front passenger when the SRS side airbags are inflated.


CAUTION


SRS side airbags inflate with consid- erable force. To avoid potential death or serious injury when they inflate, the driver and front passenger must: D Wear their seat belts properly. D Remain properly seated with their back upright and against the seat at all times.


light system monitors


This indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after about 6 seconds. This means the SRS side airbags are operat- ing properly. This warning the airbag sensor assembly, front airbag sen- sors, side airbag sensors, driver’s seat position sensor, driver’s seat belt buckle switch, front seat belt pretensioner assem- blies, inflators, warning light, interconnect- ing wiring and power sources. (For details, see indicators and warning buzzers” on page 85 in Section 1−5.)


reminder


“Service


48


2003 MY COROLLA_U (OM12744U)


from


The SRS side airbag system may not activate if the vehicle is subjected to a collision the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment as shown in the illustra- tion. The SRS side airbags are designed to inflate when the passenger compartment area suffers a severe the side. For the safety of all occupants, always wear your seat belts properly.


impact


from


Collision from the rear


Collision from the front


Vehicle rollover


The SRS side airbags are not designed to inflate if the vehicle is involved in a front or rear collision, if it rolls over, or if it is involved in a low−speed side collision.


’03 Corolla U (L/O 0201)


In a severe side impact, the side airbag sensor triggers the side airbag inflators. At this time a chemical reaction in the inflators quickly fills the airbags with non− toxic gas to help restrain the lateral mo- tion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non−toxic gas. This does not indicate a fire. This gas is nor- mally harmless; however, for those who have delicate skin, it may cause a minor skin irritation. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Front seats may be hot for several min- utes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.


The SRS side airbag system consists mainly of the following components, and their locations are shown in the illustra- tion. 1. SRS warning light 2. Side airbag modules


(airbag and inflator) 3. Side airbag sensors 4. Airbag sensor assembly The SRS side airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sen- sor and airbag sensor.


2003 MY COROLLA_U (OM12744U)


49


’03 Corolla U (L/O 0201)


CAUTION


D The SRS side airbag system is de- signed only as a supplement to the primary protection of the driver side and front passenger side seat belt systems. To ensure maximum protection in an accident, the driver and all passengers in the vehicle must wear their seat belts properly. Wearing a seat belt properly during an accident reduces the chances of death or serious injury or being thrown out of the vehicle. For instructions and precautions con- cerning the seat belt system, see “Seat belts” on page 32 in this sec- tion.


restraint


D Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing airbags. An infant or child who is too small to use a seat belt should be properly secured using a child Toyota strongly recommends in- fants and children be placed in the rear seat of the vehicle and proper- ly restrained. The rear seat is the safest for infants and children. For instructions concerning the installa- tion of a child restraint system, see “Child restraint” on page 53 in this section.


that all


system.


if he/she


D Do not allow a child to lean his/her head or any part of his/her body against the front door or the area of the seat from which the side air- bag deploys even is seated in the child restraint system. It is dangerous if the side airbag inflates, and the impact could cause death or serious injury to the child. For the installation of a child restraint sys- tem, see “Child restraint” on page 53 in this section.


instructions concerning


50


2003 MY COROLLA_U (OM12744U)


D Do not lean against the front door when the vehicle is in use, since the side airbag inflates with consid- erable speed and force. Otherwise, you may be killed or be seriously injured. Spacial care should be tak- en especially when you have a small child in the vehicle.


D Sit up straight and well back in the seat, distributing your weight evenly in the seat. Do not apply excessive weight to the outer side of the front seats on vehicles with side airbags.


’03 Corolla U (L/O 0201)


D Do not use seat accessories which cover the parts where the side air- bags inflate. Such accessories may prevent the side airbags from acti- vating correctly, causing death or serious injury.


D Do not modify or replace the seats or upholstery of front seats with side airbags. Such changes may disable the system or cause the side airbags to inflate accidentally, resulting in death or serious injury. Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repairs and modifications.


NOTICE


consulting


Do not perform any of the following changes without your Toyota dealer. Such changes can interfere with proper operation of the SRS side airbag system in some cases. z Installation of electronic devices such as a mobile two−way radio, cassette tape player or compact disc player


z Modification of the suspension sys-


tem


z Modification of the side structure of


the passenger compartment


z Repairs made on or near the con-


sole or front seat


2003 MY COROLLA_U (OM12744U)


51


D Do not attach a cup holder or any other device or object on or around the door. When the side airbag in- flates, the cup holder or any other device or object will be thrown with great force or the side airbag may not activate correctly, resulting in injury. Likewise, death or serious the driver and front passenger should not hold objects their arms or on their knees.


in


’03 Corolla U (L/O 0201)


NOTICE


Do not disconnect the battery cables before contacting your Toyota dealer.


In the following cases, contact your Toyota dealer as soon as possible: D The SRS side airbags have been in-


flated.


D The portion of the doors (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS side airbags to inflate.


D The surface of the seats with the side airbag (shaded is scratched, cracked, or otherwise dam- aged.


illustration)


the


in


following


conditions occurs,


This SRS side airbag system has a service reminder indicator to inform the driver of operating problems. If either of the this indicates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or the light remains on.


D The light comes on or flashes while


driving.


52


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all 50 states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAE J1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts” on page 32 for details.


CAUTION


D For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.


D Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, installed on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. D Never install a rear−facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear−facing child restraint system is installed on the front seat.


D Unless


it install a straint system on the front seat.


is unavoidable, do not forward−facing child re-


the


D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the force of the deploying front passenger air- bag could cause death or serious injury to the child.


D On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbags inflate, because impact could cause death or serious injury to the child. D Make sure that you have complied with all installation instructions pro- vided restraint manufacturer and that the system is properly secured.


child


the


the


by


2003 MY COROLLA_U (OM12744U)


53


’03 Corolla U (L/O 0201)


D After


installing the child restraint system, make sure it is secured in place following the manufacturer’s instructions. If it is not restrained securely, it may cause death or se- rious the event of a sudden stop or accident.


the child


injury


to


in


When not using the child restraint system, keep it secured with the seat belt or place it in the trunk or somewhere other than the passenger compartment. This will pre- vent the event of a sudden stop or accident.


injuring passengers


from


in


it


—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap por- tion of the lap/shoulder belt. You must carefully consult the manufacturer’s instructions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. restraint system should be The child installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.


CAUTION


D Never install a rear−facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear−facing child restraint system is installed on the front seat.


D Unless


it install a straint system on the front seat.


is unavoidable, do not forward−facing child re-


the


D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the force of the deploying front passenger air- bag could cause death or serious injury to the child.


D On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbags inflate, because impact could cause death or serious injury to the child.


the


54


2003 MY COROLLA_U (OM12744U)


—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchor brackets for se- curing the top strap of a child restraint system. For instructions about how to use the an- chor bracket, see “—Using a top strap” on page 65 in this section. The child restraint lower anchorages ap- proved for your vehicle may also be used. See “—Installation with child restraint low- er anchorages” on page 67 in this section.


’03 Corolla U (L/O 0201)


(A) Infant seat


(C) Booster seat


(B) Convertible seat


2003 MY COROLLA_U (OM12744U)


55


’03 Corolla U (L/O 0201)


—Installation with 3−point type seat belt


(A) INFANT SEAT INSTALLATION An infant seat is used in rear−facing position only.


CAUTION


D Never install a rear−facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.


56


2003 MY COROLLA_U (OM12744U)


the


lock mechanism of


D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. This can cause death or serious injury to a child and front passenger in case of a sudden braking or collision.


D If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.


’03 Corolla U (L/O 0201)


CAUTION


D After inserting the tab, make sure that the tab and buckle are locked, and the lap and shoulder portions of the belt are not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the child restraint system until the seat belt is fixed.


from


1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.


2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.


the


To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.


2003 MY COROLLA_U (OM12744U)


57


’03 Corolla U (L/O 0201)


3. While pressing the infant seat


firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.


CAUTION


Push and pull the child restraint sys- tem in different directions to make sure the it installation instructions provided by its manufacturer.


is secure. Follow all


4. To remove the infant seat, press the buckle−release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.


freely again and be ready


58


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward− facing or rear−facing position depend- ing on the child’s age and size. When installing, follow the manufacturer’s in- structions about the applicable child’s age and size as well as directions for installing the child restraint system.


CAUTION


D Never install a rear−facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.


Move seat fully back


the


D A forward−facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible, because the force of the deploying front passenger air- bag could cause death or serious injury to the child.


2003 MY COROLLA_U (OM12744U)


59


’03 Corolla U (L/O 0201)


D On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbags inflate, because impact could cause death or serious injury to the child.


the


1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.


provided insert the


by tab


the


lock mechanism of


D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. This can cause death or serious injury to a child and front passenger in case of a sudden braking or collision.


D If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.


60


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


CAUTION


D After inserting the tab, make sure that the tab and buckle are locked, and the lap and shoulder portions of the belt are not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the child restraint system until the seat belt is fixed.


from


2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.


To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.


3. While pressing


the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.


2003 MY COROLLA_U (OM12744U)


61


’03 Corolla U (L/O 0201)


CAUTION


Push and pull the child restraint sys- tem in different directions to make sure the it installation instructions provided by its manufacturer.


is secure. Follow all


4. To remove the convertible seat, press the buckle−release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.


freely again and be ready


(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward−fac- ing position only.


62


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


D On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbags inflate, because impact could cause death or serious injury to the child.


the


Move seat fully back


CAUTION


the


D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the force of the deploying front passenger air- bag could cause death or serious injury to the child.


1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.


insert


the


tab


Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” on page 32 for details.


2003 MY COROLLA_U (OM12744U)


63


’03 Corolla U (L/O 0201)


D If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the child restraint system until the seat belt is fixed.


from


2. To remove the booster seat, press the the


buckle−release button and allow belt to retract.


CAUTION


D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.


to do so could reduce


D Both high−positioned lap belts and loose−fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on a child’s hips as possible.


D For child’s safety, do not place the


shoulder belt under child’s arm.


D After inserting the tab, make sure that the tab and buckle are locked, and the lap and shoulder portions of the belt are not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.


64


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


—Using a top strap


Symbol


Anchor brackets


Follow the procedure below for a child restraint system that requires the use of a top strap.


Use the anchor bracket on the package tray behind the rear seat to attach the top strap. Anchor brackets are rear seating position. This symbol indicates the location of the anchor brackets.


for each


installed


TO USE THE ANCHOR BRACKET: 1. Outside anchor brackets only—


Remove the head restraint.


2003 MY COROLLA_U (OM12744U)


65


’03 Corolla U (L/O 0201)


2. Open the lid of the anchor bracket.


3. Securely


fasten


the child restraint


system with the seat belt. Latch bracket and tighten the top strap.


the hook onto


the anchor


4. Outside anchor brackets only—


Replace the head restraint.


instructions


For the child re- straint system, see “Child restraint” on page 53 in this section.


install


to


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


2003 MY COROLLA_U (OM12744U)


66


’03 Corolla U (L/O 0201)


—Installation with child restraint lower anchorages


for child restraint Lower anchorages systems complying with FMVSS225
specifications are installed in the rear seat. The anchorages are installed in the clear- ance between the seat cushion and seat- back of both outside rear seats. Child restraint systems complying with FMVSS225 specifications can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt.


Type A


Type B


2003 MY COROLLA_U (OM12744U)


67


’03 Corolla U (L/O 0201)


SYSTEM


CAUTION


Tilt steering wheel


D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages and that the seat belt is not caught.


in different directions


D Push and pull the child restraint system to make sure it is secure. Follow all the instructions pro- vided by its manufacturer.


installation


the


lock mechanism of


D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. This can cause death or serious injury to a child and front passenger in case of a sudden braking or collision.


To change the steering wheel angle, hold the steering wheel, push down the lock the steering wheel to the desired angle and return the lever to its original position.


release


lever,


tilt


RESTRAINT


CHILD INSTALLATION Type A— 1. Widen


the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages near the tag on the seatback.


2. Latch the hooks of lower straps onto the anchorages and tighten the lower straps. Type B— 1. Widen


the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages near the tag on the seatback.


2. Latch the buckles onto the anchor-


ages.


it should be anchored. (For


If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 65 in this section.) For the installation details, refer to the in- struction manual equipped with each prod- uct.


68


2003 MY COROLLA_U (OM12744U)


CAUTION


D Do not adjust the steering wheel while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.


D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.


’03 Corolla U (L/O 0201)


Outside rear view mirrors—


CAUTION


Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.


NOTICE


The outside rear view mirrors are fixed in place. Do not try to fold the mirrors. It may damage the mirrors.


Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.


2003 MY COROLLA_U (OM12744U)


69


’03 Corolla U (L/O 0201)


—Power rear view mirror control


Anti−glare inside rear view mirror


NOTICE


If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.


To adjust a mirror, use the switches. 1. Master switch—To select the mirror to


the switch to “L” (left) or “R”


be adjusted Push (right). 2. Control


switch—To move


ror P ush direction.


the switch


in


the mir- the desired


Mirrors can be adjusted when the key is in the “ACC” or “ON” position.


70


2003 MY COROLLA_U (OM12744U)


Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.


’03 Corolla U (L/O 0201)


Auto anti−glare inside rear view mirror


CAUTION


Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.


Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti− glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.


ignition key


the


is


” switch.


to reduce


In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off the automatic function, push the “ To turn on the automatic function again, push the “ Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it may take a little longer for the mirror to darken the detection of headlights.


in response


” switch.


to


CAUTION


Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.


2003 MY COROLLA_U (OM12744U)


71


’03 Corolla U (L/O 0201)


Vanity mirrors


Driver’s side only—To use the vanity mirror, open the cover.


To ensure correct functioning of an anti−glare mirror sensor located on the back side of the mirror, do not touch or cover the sensor with your finger or a piece of cloth, etc.


Driver’s side


72


2003 MY COROLLA_U (OM12744U)


Front passenger’s side


’03 Corolla U (L/O 0201)


SECTION 1− 4


OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Front fog lights Interior/instrument panel light controlol Personal lights Windshield wipers and washer Rear window defogger


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


74
76
77
77
78
79
79


2003 MY COROLLA_U (OM12744U)


73


’03 Corolla U (L/O 0201)


Headlights and turn signals


NOTICE


To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.


tail,


license plate,


HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Light reminder buzzer A buzzer will remind you to turn the lights off when the driver’s door is opened if you remove the key with the headlight switch on.


the


74


2003 MY COROLLA_U (OM12744U)


Daytime running light system (for U.S.A.) Daytime running light system can make it easier for others to see the front of your vehicle during the day. This system can be helpful in many different driving condi- tions, but they can be especially helpful in the short periods after dawn and before sunset. This system will make your headlights come on at a reduced brightness when: D The engine is running. D The parking brake is released. D The headlight/turn signal lever knob is


in the “OFF” position.


to full intensity


To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights for night driving. The headlights automatically switch to full the or reduced darkness of the daytime running light system is activated. Also, the other exterior lights and instru- ment panel lights automatically turn on or off.


intensity depending on the surroundings when


’03 Corolla U (L/O 0201)


Daytime running light system (for Canada) Daytime running light system can make it easier for others to see the front of your vehicle during the day. This system can be helpful in many different driving condi- tions, but they can be especially helpful in the short periods after dawn and before sunset. This system will make your headlights come on at a reduced brightness when: D The engine is running. D The parking brake is released. D The headlight/turn signal lever knob is


in the “OFF” position or position 1.


To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights for night driving.


to full intensity


The daytime running light control sensor is on the top of the driver’s side instru- ment panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor.


High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.


the lever all


2003 MY COROLLA_U (OM12744U)


75


’03 Corolla U (L/O 0201)


Emergency flashers


NOTICE


To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.


TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 225 in Section 7−3. 76


flashers,


turn on


the emergency


To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


Front fog lights


Interior/instrument panel light control


OFF ON


DOOR


To turn on the front fog lights, twist the band of the headlight/turn signal lever. They will come on only when the headlights are on low beam.


interior


light dial has


INTERIOR LIGHT To turn on the interior light, turn the dial. The positions: OFF—Turns the light off. ON—Keeps the light on all the time. DOOR—Turns the light on when any of the doors is opened. The light goes off when all the doors are closed.


the following


Illuminated entry system With the dial in the DOOR position, the light comes on when any door is opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. However, in the following cases, the light goes out immediately: D All the doors are closed when the igni- tion key is in “ACC” or “ON” position. D The ignition key is turned to “ACC” or


“ON” after all the doors are closed.


D All the doors are locked when the light


is still on.


When any door is unlocked with the key or wireless remote control transmitter, the light comes on for 15 seconds, even if the door is not opened. To prevent the battery being discharged, the lights will automatically turn off when the key is removed and the door is left opened with the dial in the DOOR position for 20 minutes or more.


2003 MY COROLLA_U (OM12744U)


77


’03 Corolla U (L/O 0201)


Personal lights


INSTRUMENT PANEL LIGHT To adjust the brightness of the instru- ment panel lights, turn the dial.


Type A


Type C


To turn on the personal light, push the switch. To turn it off, push the switch once again.


78


2003 MY COROLLA_U (OM12744U)


Type B


’03 Corolla U (L/O 0201)


Windshield wipers and washer


Rear window defogger


to


the


increase


interval adjuster: The


With “INT TIME” band lets you adjust the wiping time inter- val when the wiper lever is in the intermit- tent position (position 1). Twist the band upward time between sweeps, and downward to decrease it. To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 225 in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.


the washer


NOTICE


Do not operate the wipers if the wind- shield the glass.


It may scratch


is dry.


To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.


Lever position


Speed setting


Position 1


Position 2


Position 3


Intermittent


Slow


Fast


For a single sweep of push the lever up and release it.


the windshield,


To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the sur- faces. An indicator light will illuminate to indicate the defogger is operating. Push the switch once again to turn the defogger off. The system will automatically shut off af- ter the defogger has operated about 15
minutes.


2003 MY COROLLA_U (OM12744U)


79


’03 Corolla U (L/O 0201)


Make sure you turn the defogger off when the window is clear. Leaving the defogger on for a long time could cause the battery to discharge, especially during stop−and− go driving. The defogger is not designed for drying rain water or for melting snow.


NOTICE


When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.


80


2003 MY COROLLA_U (OM12744U)


’03 Corolla U (L/O 0201)


SECTION 1− 5


OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine coolant temperature gaugege . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outside temperature display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzersrs . . . . . . . . . . . . . .


82
82
83
84
84
85


2003 MY COROLLA_U (OM12744U)


81


’03 Corolla U (L/O 0201)


Fuel gauge


Engine coolant temperature gauge


indicates


The gauge the approximate quantity of the fuel remaining in the tank when the ignition switch is on. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. The needle moves when braking, acceler- ating or making turns. This is caused by the fuel moving in the tank. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.


2003 MY COROLLA_U (OM12744U)


Type A


Type B


Type A


Type B


82


The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high


speed driving.


D Idling for a long period with the air conditioning on in stop−and−go traffic.


D Towing a trailer.


NOTICE


z Do not remove the thermostat


in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.


’03 Corolla U (L/O 0201)


Tachometer


z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” on page 173 in Section 4.


The tachometer indicates engine speed in thousands of rpm (revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.


NOTICE


Do not let the indicator needle get into the red zone. This may cause severe engine damage.


2003 MY COROLLA_U (OM12744U)


83


’03 Corolla U (L/O 0201)


Odometer and two trip meters


Outside temperature display


3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.


to


Centigrade display


Fahrenheit display


trip meters when


This meter displays the odometer and two ignition switch is on. 1. Odometer—Shows


total distance


the


the


the vehicle has been driven.


2. Two


trip meters—Show


two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.


fuel economy and


the other


84


2003 MY COROLLA_U (OM12744U)


from


temperature


The outside temperature is indicated on the display when the ignition switch is on. The displayed ranges −30_C (−22_F) up to 50_C (122_F). If there is any abnormality in the connec- tion of the outside air temperature sensor, “−−” will appear on the display. If “−−” ap- pears on the display, contact your Toyota dealer. There may be a case that “−−” appears momentarily when the ignition is quickly turned to “ON”. It is normal if it goes out soon.


’03 Corolla U (L/O 0201)


Service reminder indicators and warning buzzers


If the indicator or buzzer comes on...


Do this.


If the indicator or buzzer comes on...


Do this.


(a)


(b)


(c)


(d)


or


If parking brake is off, stop immediately and contact Toyota dealer.


Fasten driver’s seat belt.


(indicator and buzzer)


Fasten front passenger’s seat


belt.


Stop and check.


(e)


(f)


(g)


(h)


or


or


Take vehicle to Toyota dealer.


Fill up tank.


Stop and check.


Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and


Loading...
x