2000 Toyota Corolla Owners Manual

range, install the filler cap hand- tight. Oil quantity, L (qt., lmp. qt.):

1.3 (1.4, 1.1)

NOTICE

(cid:1) Avoid overfilling, or the engine

could be damaged.

(cid:1) Check the oil level on the dipstick

once again after adding the oil.

Engine oil selection Use API grade SJ, “Energy- Conserving” or ILSAC multigrade engine oil. Recommended viscosity (SAE):

for good

SAE 5W- 30 is the best choice for your vehicle, fuel economy, and good starting in cold weather. If you use SAE 10W- 30 engine oil in extremely low temperatures, the engine may become difficult to start, so SAE 5W- 30 engine oil is recommended.

Checking the engine oil level

Low level

Full level

Add oil

O.K.

Too full

With the engine at operating tempera- ture and turned off, check the oil level on the dipstick. 1. To get a

the vehicle should be on a level spot. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.

reading,

true

2. Pull out the dipstick, and wipe it clean

with a rag.

3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.

4. Pull the dipstick out and look at the oil

level on the end.

206

2000 Corolla(U)

Oil identification marks Either or both API registered marks are added to some oil containers to help you select the oil you should use. The API Service Symbol is located any- where on the outside of the container. The top portion of the label shows the oil quality by API (American Petroleum Insti- tute) designations such as SJ. The center portion of the label shows the SAE viscos- ity grade such as SAE 5W- 30. “Energy- Conserving” shown in the lower portion, indicates that the oil has fuel- saving ca- pabilities. The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is displayed on the front of the container.

API service symbol

ILSAC certification mark

Checking the engine coolant level Look at the see- through coolant reser- voir when the engine is cold. The cool- ant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir. If the level is low, add ethyl- ene- glycol type coolant for a proper corrosion protection of aluminum com- ponents. The coolant level in the reservoir will vary with engine temperature. However, if the level is on or below the “LOW” line, add coolant. Bring the level up to the “FULL” line. Always use ethylene- glycol type coolant for a proper corrosion protection of alumi- num components. See information in the next column. If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, engine coolant filler cap, radiator cap and drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system.

the system. Visually check

in

207

2000 Corolla(U)

Checking brake fluid

We recommend to use 50% solution for your Toyota, to provide protection down to about -35(cid:2)C (- 31(cid:2)F). When it is extreme- ly cold, to about -50(cid:2)C (- 58(cid:2)F), 60% solution is rec- ommended. Do not use more than 70% solution for better coolant performance.

to provide protection down

NOTICE

Do not use alcohol type antifreeze or plain water alone.

Type A

Type B

CAUTION

To prevent burning yourself, do not remove the radiator cap when the en- gine is hot.

Coolant type selection Use of improper coolants may damage your engine cooling system. Your coolant must contain ethylene- glycol type coolant for a proper corrosion protection of your engine that contains aluminum compo- nents. Use “TOYOTA Long Life Coolant” or equivalent. In addition to preventing freezing and sub- sequent damage to the engine, this will also prevent corrosion. Further supplemen- tal inhibitors or additives are neither need- ed nor recommended. Read the coolant container for information on freeze protection. Follow the manufac- turer’s directions to mix with plain water (preferably demineralized water or distilled water). The total capacity of the cooling system is given in Section 8.

for how much

208

reservoir. The

To check the fluid level, simply look at the see- through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear. So be sure to keep the reservoir filled. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem. If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir. Remove and replace the reservoir cover by hand.

2000 Corolla(U)

Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.

CAUTION

Take care when filling the reservoir because brake fluid can harm your eyes and damage painted surfaces. If fluid gets in your eyes, flush your eyes with clean water.

If hot add

Checking power steering fluid

If hot O.K.

Close

If cold O.K.

Open

If cold add

NOTICE

If you spill some of the fluid, be sure to wash it off with water to prevent it from damaging the parts or paint.

III.

Check the fluid level through the reser- voir. If necessary, add automatic trans- mission fluid DEXRON(cid:3) II or If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more in frigid temperatures), the fluid is hot (60(cid:2)C—80(cid:2)C or 140(cid:2)F—175(cid:2)F). You may also check the level when the fluid is temperature, 10(cid:2)C—30(cid:2)C or 50(cid:2)F—85(cid:2)F) if the engine has not been run for about five hours.

(about

room

cold

209

2000 Corolla(U)

Checking tire pressure

Clean all dirt from outside of the reservoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add automatic fluid DEXRON(cid:3) II or III to bring the level within the range. To remove the filler cap, turn it counter- clockwise and lift up. To reinstall it, turn it clockwise. After filler cap,visually check the steering box case, vane pump and hose connections for leaks or damage.

transmission

replacing

the

CAUTION

The reservoir tank may be hot so be careful not to burn yourself.

NOTICE

Avoid overfilling, or the power steer- ing could be damaged.

210

Keep your tire pressures at the proper level. The recommended cold tire pressures, tire size and the vehicle capacity weight are given in Section 8. They are also on the tire pressure label as shown. You should check the tire pressures every two weeks, or at least once a month. And don’t forget the spare! Incorrect tire pressure can reduce tire life and make your vehicle less safe to drive.

the

results

tire pressure

tire pressure

is excessively

Low in excessive wear, poor handling, reduced fuel econo- my, and the possibility of blowouts from overheated tires. Also, low tire pressure can cause poor sealing of the tire bead. If low, there is the possibility of wheel deforma- tion and/or tire separation. High tire pressure produces a harsh ride, handling problems,excessive wear at the center of the tire tread, and a greater possibility of tire damage from road haz- ards. If a tire frequently needs refilling, have it checked by your Toyota dealer. The following instructions for checking tire pressure should be observed: (cid:1) The pressure should be checked only when the tires are cold. If your ve- hicle has been parked for at least 3
hours and has not been driven for more than 1.5 km or 1 mile since, you will get an accurate cold tire pressure reading.

(cid:1) Always use a tire pressure gauge. The appearance of a tire can be mis- leading. Besides, that are even just a few pounds off can degrade handling and ride.

tire pressures

2000 Corolla(U)

(cid:1) Take special care when adding air to the compact spare tire. The smaller tire size can gain pressure very quick- ly. Add compressed air in small quanti- ties and check the pressure often until it reaches the specified pressure.

(cid:1) Do not bleed or reduce tire pressure after driving. It is normal for the tire pressure to be higher after driving.

(cid:1) Never exceed

the vehicle capacity weight. The passenger and luggage weight should be located so that the vehicle is balanced.

(cid:1) Be sure to reinstall the tire inflation valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as possible.

Checking and replacing tires

Tread wear indicator

CHECKING YOUR TIRES Check the tires tread for the tread wear indicators. If the indicators show, re- place the tires. The tires on your Toyota have built- in tread wear indicators to help you know when the tires need replacement. When the tread depth wears to 1.6 mm (0.06
in.) or less, the indicators will appear. If you can see the indicators in two or more adjacent grooves, the tire should be re- placed. The lower the tread, the higher the risk of skidding. The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.).

Check the tires regularly for damage such as cuts, splits and cracks. If any damage is found, consult with a techni- cian and have the tire repaired or re- placed. Even if the damage does not appear seri- ous, a qualified technician should examine the damage. Objects which have pene- trated the tire may have caused internal damage. Any tires which are over 6 years old must be checked by a qualified techni- cian even if damage is not obvious. Tires deteriorate with age even have never or seldom been used. This applies also to the spare tire and tires stored for future use. REPLACING YOUR TIRES When replacing a tire, use only the same size and construction as original- ly installed and with the same or great- er load capacity. Using any other size or type of tire may seriously affect handling, ride, speedome- ter/odometer calibration, ground clearance, and clearance between the body and tires or snow chains.

they

if

211

2000 Corolla(U)

Rotating tires

CAUTION

(cid:1) Do not mix radial, bias belted, or bias- ply tires on your vehicle. It can cause dangerous handling char- acteristics, resulting in loss of con- trol.

(cid:1) Do not use tires or wheels other recom-

the manufacturer’s

than mended size.

Vehicles with compact spare tire

tire

Toyota recommends all four tires, or at least both front or rear tires be re- placed as a set. See “If you have a flat tire” in Section 4
for tire change procedure. When a is replaced, should always be balanced. An unbalanced wheel may affect vehicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.

the wheel

212

Vehicles without compact spare tire

To equalize the wear and help extend tire life, Toyota recommends that you rotate your tires approximately every 12000 km (7500 miles). However, the most appropriate timing for tire rotation may vary according to your driving hab- its and road surface conditions. See “If you have a flat tire” in Section 4
for tire change procedure. When for uneven wear and damage. Abnormal wear is usu- ally caused by incorrect tire pressure, im- proper wheel alignment, out- of- balance wheels, or severe braking.

tires, check

rotating

CAUTION

Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.

2000 Corolla(U)

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select the same size, construction and load capacity as the original tires on your Toyota. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions. SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replac- ing.

CAUTION

(cid:1) Do not drive with the snow tires

incorrectly inflated.

(cid:1) Never drive over 120 km/h (75 mph)

with any type of snow tires.

TIRE CHAIN SELECTION Use the tire chains of correct size and type. Use SAE Class “S” type radial tire chains except radial cable chains or V- bar type chains. Regulations regarding the use of tire chains vary according to location or type of road, so always check them before installing chains. CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer.

rear driving

0.5—1.0

the

If wheel covers are used, they will be scratched by the chain band,so remove the covers before putting on the chains.

CAUTION

(cid:1) Do not exceed 50 km/h (30 mph) or recom- is

the chain manufacturer’s mended speed lower.

limit, whichever

(cid:1) Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.

(cid:1) Avoid sharp turns or locked- wheel braking, as use of chains may ad- versely affect vehicle handling.

NOTICE

Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicle as well as the tire.

213

2000 Corolla(U)

Aluminum wheel precautions (cid:1) After driving your vehicle the first 1600
km (1000 miles), check that the wheel nuts are tight. repaired, or (cid:1) If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).

rotated, tires, check

that

(cid:1) When using tire chains, be careful not

to damage the aluminum wheels.

(cid:1) Use only the Toyota wheel nuts and for your aluminum

wrench designed wheels.

(cid:1) When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.

(cid:1) As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.

Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.

Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace damaged wheels, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. This must be observed on compact spare tires, too. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.

214

2000 Corolla(U)

SECTION 7- 3

DO- IT- YOURSELF MAINTENANCE Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

216
217
218
219
219

215

2000 Corolla(U)

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. (cid:1) Do not cause a spark from the bat-

tery with tools.

(cid:1) Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. (cid:1) Avoid contact with eyes, skin or

clothes.

(cid:1) Never ingest electrolyte. (cid:1) Wear protective safety glasses when

working near the battery.

(cid:1) Keep children away from the bat-

tery.

216

EMERGENCY MEASURES (cid:1) If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

(cid:1) If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

(cid:1) If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

(cid:1) If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

—Checking battery exterior

Terminals

Ground cable

Hold- down clamp

Check the battery for corroded or loose terminal connections, cracks, or loose hold- down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold- down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

2000 Corolla(U)

NOTICE

Type A

—Checking battery fluid

(cid:1) Be sure the engine and all accesso- ries are off before performing main- tenance.

(cid:1) When checking the battery, remove the ground cable from the negative terminal (“-” mark) first and rein- stall it last.

(cid:1) Be careful not to cause a short cir-

cuit with tools.

(cid:1) Take care no solution gets into the

battery when washing it.

Green

Dark

Clear or light yellow

Type B

Blue

White

Red

CHECKING BY HYDROMETER Check hydrometer color.

the battery condition by

the

Hydrometer color

Type A

Type B

GREEN

BLUE

DARK WHITE

Condition Condition

Good

Charging necessary. Have battery checked by your Toyota dealer.

CLEAR

or LIGHT YELLOW

RED

Have battery checked by your Toyota dealer.

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

(cid:1) Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

(cid:1) Only do a slow charge (5A or less). Charging at a quicker rate is dan- gerous. The battery may explode, causing personal injuries.

NOTICE

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

217

2000 Corolla(U)

Checking and replacing fuses

Type A

Good

Blown

Type B

Good

Blown

Type C

Good

Blown

218

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” in Section 7- 1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull a suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See Section 8 of this manual for the functions controlled by each circuit.

Type A fuses can be pulled out by the pull- out tool. The location of the pull- out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “FOG” or “S- HTR” fuse, which may be dispensable for normal driving, and use its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close as possible to, the rating. If the amperage is fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

that specified,

lower

than

the

if

it

2000 Corolla(U)

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

Adding washer fluid If any washer does not work or low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. You may use plain water as washer fluid. in cold areas where tempera- However, tures freezing point, use fluid containing antifreeze. This washer product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

range below

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.

CAUTION

Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

NOTICE

Only use a bulb of the listed type.

219

2000 Corolla(U)

—Headlights

W Type

1. Open the hood.

RIGHT- HAND HEADLIGHT: Remove the bolts and the relay block.

take out

the relay block

Put place other than on the engine.

in

the appropriate

NOTICE

Do not place the relay block on the engine.

2. LEFT- HAND HEADLIGHT: Remove the clip and take out the air cleaner duct.

Remove and shown in the following illustration.

install

the cover clip as

Light bulbs

Headlights

front side

Parking, marker and front turn signal lights

Rear side marker lights

Rear turn signal lights

Bulb No. —

60/55

3157NA

27/8

194

3.8

3156

27

Stop and tail lights

3157

27/8

18

3.8

18

10

4.9

Back- up lights

License plate lights

High mounted stoplight

Personal light

Interior light

Trunk light

921

194

921

—

—

168

A: HB2 halogen bulbs B: Single end bulbs C: Wedge base bulbs D: Double end bulbs

220

2000 Corolla(U)

Removing clip: Use a flat- bladed screw- driver or equivalent

3. Unplug the connector. Remove the

rubber cover.

If the connector is tight, wiggle it.

4. Release

the bulb retaining spring and remove the bulb. Install a new bulb and the bulb retaining spring.

To install a bulb, align the tabs of the bulb with the mounting hole.

the cutouts of

Installing clip

221

2000 Corolla(U)

—Parking, front side marker and front turn signal lights

Use a Phillips- head screwdriver.

5. Install

the rubber cover with

the “TOP” mark upward, and snuggle on the boss. Insert the connector.

Make sure the rubber cover fits snugly on the connector and the headlight body. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

222

2000 Corolla(U)

—Rear side maker, rear turn signal, and stop and tail lights

Removing:

Installing:

Removing clips (type B): Use a Phillips- head screwdriver.

Removing and installing clips (type A): Use a flat- bladed screwdriver or equivalent.

Installing clips (type B)

223

2000 Corolla(U)

—Back- up lights

a: Stop and tail light b: Rear turn signal light c: Rear side marker light

224

2000 Corolla(U)

—License plate lights (left side)

225

2000 Corolla(U)

—License plate lights (right side)

—High mounted stoplight

226

2000 Corolla(U)

227

2000 Corolla(U)

228