2000 Toyota Corolla Owners Manual

depressing the clutch pedal, as this may cause engine racing or overrev- ving.

CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling the lever in the “CANCEL” di-

rection and releasing it.

b. Depressing the brake pedal. c. Depressing

the clutch pedal (manual

transmission).

If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto- matically cancel out. If the vehicle speed drops 16 km/h (10
mph) below the preset speed,the preset speed will also automatically cancel out.

lever or by depressing

On vehicles with 4- speed automatic trans- mission, even if you turn off the overdrive switch, with the cruise control on, engine braking will not be applied because the cruise control is not cancelled. To de- crease the vehicle speed, reset to a slow- er speed with the cruise control lever or depress the brake pedal. If you use the brake pedal, cruise control is cancelled. RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal or clutch pedal, pushing the lever up in the “RES/ACC” direction will restore the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARNING If the instrument cluster flashes when using the cruise “CRUISE ON·OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system.

“CRUISE”

indicator

control,

press

light

the

the

in

103

2000 Corolla(U)

(cid:2) The indicator light does not come on. (cid:2) The indicator light flashes again. (cid:2) The

light goes out after

indicator

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

104

2000 Corolla(U)

SECTION 1- 7

OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Car audio system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

106
106
124

105

2000 Corolla(U)

Reference

Type 1: AM·FM ETR radio

Type 3: AM·FM ETR radio/cassette player/ compact disc auto changer controller

Type 2: AM·FM ETR radio/cassette player

Type 4: AM·FM ETR radio/compact disc player

106

“FM”,

“AM”,

“AM·FM”,

“VOL/PWR”,

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “VOL/PWR”, “PWR·VOL” or “PWR/ VOL” to turn the audio system on and off. Push “TAPE” or “CD” to turn on that function without push- ing “PWR/ VOL”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “TAPE” or “CD” if the system is already on but you want to switch from one function to anoth- er.

“PWR·VOL” or

“AM·FM”,

“AM”,

“FM”,

2000 Corolla(U)

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble and bass levels. In fact, differ- ent kinds of music and vocal programs usually sound better with different mixes of treble and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

YOUR RADIO ANTENNA To lower a manual antenna, carefully push it down.

NOTICE

To prevent damage to the antenna, make sure it is retracted before driv- ing your Toyota through an automatic car wash.

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.

8 cm (3 in.) compact disc singles Your compact disc player does not need an adaptor to play compact disc singles. Compact disc singles are about 8 cm (3
in.) than standard discs. After you eject a compact disc single, do not insert a standard 12 cm (5 in.) disc until “DISC” disappears from the display.

in diameter- smaller

107

2000 Corolla(U)

NOTICE

Do not use an adaptor for compact disc singles—it could cause tracking errors or interfere with the ejection of compact discs.

108

2000 Corolla(U)

—Controls and features (cid:1)Type 1

Details of specific buttons, controls and features are described in the alphabetical listing that follows.

109

2000 Corolla(U)

TUNE Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the “(cid:1)” (up) or “(cid:2)” (down) side of “TUNE” to step up or down the station band. (If you hear a beep, you held the button too long and the radio will go into the seek mode.) Seeking In plays station band. To seek a station, push and hold the “(cid:1)” or “(cid:2)” side of “TUNE” until you hear a beep. Do this again to find another sta- tion.

the radio finds and the next station up or down the

the seek mode,

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button number will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and one FM station for each button. The preset station memory will be canceled out if the power source is interrupted (battery dis- connected or fuse blown). AM·FM Push “AM·FM” to switch between the AM and FM bands. “AM” or “FM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM·FM”.

the right and

BAL (Balance) Turn the “BAL” knob with pulling to adjust the balance between left speakers. PWR·VOL (Power·Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TONE Move the “TONE” ring around “BAL” to adjust the tone.

110

2000 Corolla(U)

(cid:1)Type 2

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

111

2000 Corolla(U)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button number will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and one FM station for each button. The preset station memory will be canceled out if the power source is interrupted (battery dis- connected or fuse blown).

(Eject button)

Push this button to eject a cassette. AM·FM Push “AM·FM” to switch between the AM and FM bands. “AM” or “FM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM·FM”. Also, push “AM·FM” to switch from cassette op- eration to radio operation.

112

fast

tape

forwards completely,

BAL (Balance) Move the “BAL” ring around “TONE” to adjust the balance between the right and left speakers FF (Fast forward) Push the “FF” to fast forward a cassette tape. To stop the tape while it is fast forward- ing, lightly push the “REW”. If a the cassette player will play the other side of the tape, using the auto- reverse feature. PROG (Program) Push “PROG” to select the other side of a cassette tape. Auto- reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding. REW (Rewind) Push the “REW” to rewind to a tape. To stop the tape while it lightly push the “FF”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side.

feature: After

is rewinding,

ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push “TAPE” to switch from radio opera- tion the audio system is off, you can turn on the cas- sette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TONE Turn the “TONE” knob to adjust the tone.

to cassette operation.

If

the seek mode,

TUNE Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the “(cid:1)” (up) or “(cid:2)” (down) side of “TUNE” to step up or down the station band. (If you hear a beep, you held the button too long and the radio will go into the seek mode.) Seeking In plays station band. To seek a station, push and hold the “(cid:1)” or “(cid:2)” side of “TUNE” until you hear a beep. Do this again to find another sta- tion. VOL/PWR (Volume/Power) Push “VOL/PWR” to turn the audio system on and off. Turn “VOL/PWR” to adjust the volume.

the radio finds and the next station up or down the

2000 Corolla(U)

113

2000 Corolla(U)

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

(cid:1)Type 3

114

2000 Corolla(U)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button number will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM”).

(Eject button)

Push this button to eject a cassette. After you turn the ignition to “LOCK”, you will be able to eject a cassette but you will not be able to reinsert it.

(Reverse/Fast forward buttons)

the

the

fast

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto- re- verse feature. Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing.

is used

to adjust

AM Push “AM” to switch the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. AUDIO CONTROL / MODE Manual tone adjustment function— This knob the manually. tone adjustment, push For “AUDIO CONTROL / MODE” repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show range “BAS -5” to “BAS 5”. tone adjustment, push For high- pitch “AUDIO CONTROL / MODE” repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show range “TRE -5” to “TRE 5”.

low- pitch

from

from

tone

the

the

115

2000 Corolla(U)

to adjust

is also used

the display. Then

Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “AUDIO CONTROL / MODE” repeatedly until “FAd” appears on turn the knob to adjust the front/rear balance. The display will show the range from “FAd F7” to “FAd R7”. For “AUDIO CONTROL / MODE” repeatedly until “BAL” appears on the knob to adjust the left/right balance. The display will show the range from “BAL L7” to “BAL R7”.

left/right adjustment, push

the display. Then

turn

time you push “CD”,

CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes between single disc play- er and automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly.

inserted up- side down. Clean

116

is

it the

inside

loaded

If “Err 2” appears on the display, indicates no disc magazine, insert a disc. If “Err 3” or “Err 4” on the display, it indicates there is a trouble inside the sys- tem. Eject the disc or magazine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC (cid:2)(cid:1) Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display.

2000 Corolla(U)

top side,

PROG (Program) Push “PROG” to select the other side of tape. The display a cassette indicates ” indi- which side is currently selected (“ indicates bottom cates side). Auto- reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

”

“

B NR*

Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, push the button marked with the double- D symbol. The double- D symbol will appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM Push “FM” to switch the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM sta- tions, two for each button. If the audio system is off, you can turn on the radio by pushing “FM”. Also, push “FM” to switch from cassette or compact disc operation to radio operation.

to

the

listen

RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. To randomly play the tracks on a disc: Quickly push and release ”RAND”. ”RAND” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push the ”RAND” a second time. Compact disc auto changer only— To randomly play all the tracks magazine: Push and hold “RAND” until you hear a beep. “D·RAND” will appear on the display and the player will perform all the tracks on all the discs in the magazine in ran- dom order. To turn off the random feature, push “RAND” a second time.

in the

117

2000 Corolla(U)

RPT (Repeat) There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” while the track is playing. “RPT” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “RPT” until you hear a beep. “D·RPT” will appear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for a few seconds, and then move to the next preset station. To select a station, push “SCAN” a second time. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for a few seconds, and then scan again. To select a station, push “SCAN” a second time.

118

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning for the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first tracks of all the discs in the magazine. To select a track, push the “SCAN” a second time. If the player scanned all the tracks on the disc, it will stop scanning. Compact disc auto changer only— Scanning the first discs in the magazine: Push and hold “SCAN” until you hear a beep. “D·SCAN” will appear on the display and the player will perform the first track of the next disc. To select a disc, push the “SCAN” a second time. If the player has scanned all it will stop scanning.

tracks of all the

the discs,

for

ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TRACK Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly.

the beginning of

up/down

button):

(Track

to

2000 Corolla(U)

the seek mode,

TUNE Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the “(cid:1)” (up) or “(cid:2)” (down) side of “TUNE” to step up or down the station band. (If you hear a beep, you held the button too long and the radio will go into the seek mode.) Seeking In plays station band. To seek a station, push and hold the “(cid:1)” or “(cid:2)” side of “TUNE” until you hear a beep. Do this again to find another sta- tion. VOL/PWR (Volume/Power) Push “VOL/PWR” to turn the audio system on and off. Turn “VOL/PWR” to adjust the volume.

the radio finds and the next station up or down the

119

2000 Corolla(U)

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

(cid:1)Type 4

120

2000 Corolla(U)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button number will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM·FM”).

(Eject button)

Push this button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a disc but you will not be able to reinsert it.

to fast

(Reverse/Fast forward buttons) If you want forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM·FM Push “AM·FM” to switch between the AM and FM bands. “AM”, “FM1” or “FM2” will appear on the display. These systems al- low you to set twelve FM stations, two for each button. If the audio system is off, you can turn on the radio by pushing “AM·FM”. Also, push from compact disc operation to radio operation. AUDIO CONTROL / MODE Manual tone adjustment function— This knob the manually. tone adjustment, push For “AUDIO CONTROL / MODE” repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show range “BAS -5” to “BAS 5”.

to switch

to adjust

low- pitch

“AM·FM”

is used

from

tone

the

the

from

to adjust

is also used

tone adjustment, push For high- pitch “AUDIO CONTROL / MODE” repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show range “TRE -5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “AUDIO CONTROL / MODE” repeatedly until “FAd” appears on the turn knob to adjust the front/rear balance. The display will show the range from “FAd F7” to “FAd R7”. For “AUDIO CONTROL / MODE” repeatedly until “BAL” appears on the knob to adjust the left/right balance. The display will show the range from “BAL L7” to “BAL R7”.

left/right adjustment, push

the display. Then

the display. Then

turn

121

2000 Corolla(U)

time you push “CD”,

CD (Compact Disc) Push “CD” to switch from radio operation to compact disc operation. If the audio system is off, you can turn on the com- pact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes between built- in single disc player and automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly.

inserted up- side down. Clean

122

is

it the

inside

loaded

If “Err 2” appears on the display, indicates no disc magazine, insert a disc. If “Err 3” or “Err 4” on the display, it indicates there is a trouble inside the sys- tem. Eject the disc or magazine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC (cid:2)(cid:1) Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. PWR/VOL (Power/Volume) Push “PWR/VOL” to turn the audio system on and off. Turn “PWR/VOL” to adjust the volume.

to

the

listen

RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. To randomly play the tracks on a disc: Quickly push and release ”RAND”. ”RAND” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push the ”RAND” a second time. Compact disc auto changer only— To randomly play all the tracks magazine: Push and hold “RAND” until you hear a beep. “D·RAND” will appear on the display and the player will perform all the tracks on all the discs in the magazine in ran- dom order. To turn off the random feature, push “RAND” a second time.

in the

2000 Corolla(U)

RPT (Repeat) There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” while the track is playing. “RPT” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “RPT” until you hear a beep. “D·RPT” will appear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for a few seconds, and then move to the next preset station. To select a station, push “SCAN” a second time. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for a few seconds, and then scan again. To select a station, push “SCAN” a second time.

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning for the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first tracks of all the discs in the magazine. To select a track, push the “SCAN” a second time. If the player scanned all the tracks on the disc, it will stop scanning. Compact disc auto changer only— Scanning the first discs in the magazine: Push and hold “SCAN” until you hear a beep. “D·SCAN” will appear on the display and the player will perform the first track of the next disc. To select a disc, push the “SCAN” a second time. If the player has scanned all it will stop scanning.

tracks of all the

the discs,

for

123

2000 Corolla(U)

TUNE (Tuning) Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the “(cid:1)” (up) or “(cid:2)” (down) side of “TUNE” to step up or down the station band. (If you hear a beep, you held the button too long and the radio will go into the seek mode.) Seeking In plays station band. To seek a station, push and hold the “(cid:1)” or “(cid:2)” side of “TUNE” until you hear a beep. Do this again to find another sta- tion.

the radio finds and the next station up or down the

the seek mode,

Car audio system operating hints

NOTICE

To ensure the correct audio system operation: (cid:1) Be careful not to spill beverages

over the audio system.

(cid:1) Do not put anything other than a cassette tape or Compact Disc into the slot.

(cid:1) The use of cellular phone inside or near the vehicle may cause a noise from the speakers of the audio sys- tem which you are listening to. However, this does not indicate a malfunction.

RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio—it is just the normal result of conditions outside the vehicle. For example, nearby buildings and terrain can interfere with FM reception. Power lines or telephone wires can interfere with AM signals. And of course, radio signals have a limited range. The farther you are from a station, the weaker its signal will be. conditions change constantly as your vehicle moves.

In addition,

reception

ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TRACK Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly.

the beginning of

up/down

button):

(Track

to

124

2000 Corolla(U)

signals are

Here are some common reception prob- lems that probably do not indicate a prob- lem with your radio: FM Fading and drifting stations—Generally, the effective range of FM is about 40 km (25
miles). Once outside this range, you may notice fading and drifting, which increase with the distance from the radio transmit- ter. They are often accompanied by distor- tion. Multi- path—FM reflective, making it possible for two signals to reach your antenna at the same time. If this happens, the signals will cancel each oth- er out, causing a momentary flutter or loss of reception. Static and fluttering—These occur when signals are blocked by buildings, trees, or other large objects. Increasing the bass level may reduce static and fluttering. the FM signal you Station swapping—If are interrupted or weak- is ened, and there is another strong station nearby on the FM band, your radio may tune in the second station until the origi- nal signal can be picked up again.

listening to

they can

AM Fading—AM broadcasts are reflected by the upper atmosphere—especially at night. These reflected signals can interfere with those received directly from the radio sta- tion, causing the radio station to sound alternately strong and weak. Station interference—When a reflected sig- nal and a signal received directly from a radio station are very nearly the same frequency, interfere with each other, making it difficult to hear the broad- cast. Static—AM is easily affected by external sources of electrical noise, such as high tension power lines, lightening, or electri- cal motors. This results in static. CARING FOR YOUR CASSETTE PLAYER AND TAPES For the best performance for your cas- sette player and tapes: Clean the tape head and other parts regu- larly. (cid:2) A dirty

tape head or tape path can decrease sound quality and tangle your cassette to clean them is by using a cleaning tape. (A wet type is recommended.)

tapes. The easiest way

Use high- quality cassettes. (cid:2) Low- quality cassette tapes can cause many problems, including poor sound, inconsistent and constant auto- reversing. They can also get stuck or tangled in the cassette player.

playing

speed,

(cid:2) Do not use a cassette if it has been damaged or tangled or if its label is peeling off.

(cid:2) Do not leave a cassette in the player if you are not listening to it, especially if it is hot outside.

(cid:2) Store cassettes in their cases and out

of direct sunlight.

(cid:2) Avoid using cassettes with a total play- ing time longer than 100 minutes (50
minutes per side). The tape used in these cassettes is thin and could get stuck or tangled in the cassette player.

125

2000 Corolla(U)

(cid:2) If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears the disc from the player and wait until it dries.

to be working. Remove

CARING FOR YOUR COMPACT DISC PLAYER AND DISCS (cid:2) Use only compact discs

labeled as

shown.

(cid:2) Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.

(cid:2) Bumpy roads or other vibrations may

make your compact disc player skip.

126

2000 Corolla(U)

CAUTION

Compact disc players use an invisible laser beam which could cause hazard- ous if directed outside the unit. Be sure to operate the player correctly.

radiation exposure

(cid:2) Your compact disc player cannot play special shaped or low- quality compact discs such as those shown here. Do not use them as the player could be damaged.

inserting

(cid:2) Handle compact discs carefully, espe- them. cially when you are them on the edge and do not Hold bend fingerprints them. Avoid getting on them, particularly on the shiny side. (cid:2) Dirt, scrapes, warping, pin holes, or other disc damage could cause the player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.)

(cid:2) Remove discs from the compact disc

them. Store

player when you are not listening to their plastic cases away from moisture, heat, and direct sunlight.

them

in

To clean a compact disc: Wipe it with a soft, lint- free cloth that has been damp- ened with water. Wipe in a straight line from the center to the edge of the disc (not in circles). Dry it with another soft, lint- free cloth. Do not use a conventional record cleaner or anti- static device.

127

2000 Corolla(U)

128

2000 Corolla(U)

SECTION 1- 8

OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Controls Air flow selector settings Operating tips Side vents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

130
133
133
135

129

2000 Corolla(U)

1. Temperature Selector 2. Air Intake Selector 3. Air Flow Selector 4. “A/C” Button 5. Fan Speed Selector

Controls

130

Fan speed selector Turn the knob to adjust the fan speed—to the right to increase, to the left to de- crease. Temperature selector Turn the knob to adjust the temperature— to the right to warm, to the left to cool.

2000 Corolla(U)

5. Windshield—Air flows mainly from the

windshield vents. Use with the air intake selector posi- tioned in Fresh.

For details about air flow selector settings, see the illustration after “A/C” button. Turning the air flow control knob to wind- shield or floor/windshield position turns on the defroster- linked air conditioning. At this time, the “A/C” button indicator comes on regardless of whether or not the “A/C” button is pressed in. This is to clean up the front view more quickly. When the “A/C” button is not pressed in, turning the air flow control knob to anoth- er position turns off the air conditioning.

131

Air flow selector Turn the knob to select the vents used for air flow. 1. Panel—Air

flows mainly

from

the

instrument panel vents.

2. Bi- level—Air flows from both the floor vents and the instrument panel vents. 3. Floor—Air flows mainly from the floor

vents.

the

4. Floor/Windshield—Air

flows mainly floor vents and windshield

from vents. Use with the air intake selector posi- tioned in Fresh.

2000 Corolla(U)

“A/C” button To turn on the air conditioning, press the “A/C” button. The “A/C” button indicator will come on. To turn the air conditioning off, press the button again. If the “A/C” button indicator flashes, there is a problem in the air conditioning system and the air conditioning automatically shuts off. If this happens, take your ve- hicle to a Toyota dealer for service.

Air intake selector Move the lever to select the air source. 1. Recirculate—Recirculates the air inside

the vehicle.

2. Fresh—Draws outside air into the sys-

tem.

132

Air flow selector settings

2000 Corolla(U)

Operating tips (cid:1) To cool off your Toyota after

it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.

(cid:1) Make sure the air intake grilles in front of the windshield are not blocked (by leaves or snow, for example).

(cid:1) On humid days, do not blow cold air on the windshield. The windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.

(cid:1) Keep the area under the front seats clear to allow air to circulate through- out the vehicle.

(cid:1) On cold days, move the fan speed to “HI” for a minute to help clear the in- take ducts of snow or moisture. This can reduce the amount of fogging on the windows.

133

2000 Corolla(U)

Heating For best results, set controls to:

Air conditioning For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards red zone Air intake—FRESH (outside air) Air flow—FLOOR Air conditioning—OFF

for a

few minutes. To keep

(cid:1) For quick heating, select recirculated air the windows from fogging, select fresh af- ter interior has been warmed.

the vehicle

(cid:1) Press the “A/C” button on for dehumidi-

fied heating.

(cid:1) Choose floor/windshield air flow to heat the vehicle interior while defrosting or defogging the windshield.

Fan speed—Any setting except “OFF” Temperature—Towards blue zone Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—ON

(cid:1) For quick cooling, move the air intake selector to recirculate for a few min- utes.

Ventilation For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards blue zone Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—OFF

(cid:1) When driving on dusty roads, close all windows. If dust thrown up by the ve- hicle is still drawn into the vehicle after closing the windows, it is recommended that the air intake selector be set to FRESH and the fan speed selector to any setting except “OFF”.

(cid:1) If following another vehicle on a dusty road, or driving in windy and dusty conditions, it is recommended that the air intake selector be temporarily set to RECIRCULATE, which will close off the outside passage and prevent outside air and dust from entering the vehicle interior.

134

2000 Corolla(U)

Defogging The inside of the windshield For best results, set controls to:

Defrosting The outside of the windshield For best results, set controls to:

Side vents

Fan speed—Any setting except “OFF” Temperature—Towards red zone to heat;

blue zone to cool Air intake—FRESH (outside air) Air flow—WINDSHIELD

turns on

Turning the air flow control knob to wind- shield position the defroster- linked air conditioning. At this time, the “A/C” button indicator comes on regard- less of whether or not the “A/C” button is pressed in. This is to clean up the front view more quickly. When the “A/C” button is not pressed in, turning the air flow control knob to a posi- tion other than windshield or floor/wind- shield turns off the air conditioning. (cid:1) On humid days, do not blow cold air on the windshield—the difference be- tween the outside and inside tempera- tures could make the fogging worse.

Fan speed—Any setting except “OFF” Temperature—Towards red zone Air intake—FRESH (outside air) Air flow—WINDSHIELD

turns on

Turning the air flow control knob to wind- shield position the defroster- linked air conditioning. At this time, the “A/C” button indicator comes on regard- less of whether or not the “A/C” button is pressed in. This is to clean up the front view more quickly. When the “A/C” button is not pressed in, turning the air flow control knob to a posi- tion other than windshield or floor/wind- shield turns off the air conditioning. (cid:1) To heat the vehicle interior while de- choose

windshield,

frosting floor/windshield air flow.

the

If air flow control is not satisfactory, check the side vents. The instrument panel vents may be opened or closed as shown.

135

2000 Corolla(U)

136

2000 Corolla(U)

SECTION 1- 9

OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Clock Cigarette lighter and ashtray Glove box Auxiliary boxes Cup holders Floor mat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

138
138
139
139
140
140

137

2000 Corolla(U)

Clock

Cigarette lighter and ashtray

ASHTRAY To use the ashtray, open out. finished with your cigarette, thor- When oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, push it back in completely. To remove the ashtray, press down on the lock spring plate and pull out.

CAUTION

To reduce the chance of in case of an accident or sudden stop while driving, always push the ash- tray back in completely after use.

injury

CIGARETTE LIGHTER To use the cigarette lighter, press it in. When it becomes heated, it automatical- ly pops out ready for use. If the engine is not running, the key must be in the “ACC” position. Do not hold the cigarette lighter pressed in. Use a Toyota genuine cigarette lighter or equivalent for replacement.

The digital clock indicates the time. The key must be in the “ACC” or “ON” position. To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock). When lights are turned on, the brightness of the time in- dication will be reduced.

instrument panel

the

138

2000 Corolla(U)

Glove box

Auxiliary boxes

To use the glove box, do this. To open: Pull the lever.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

Type A

Type C

To use the box, do the following. Type A and type B: Pull on the handle. Type C: Open the center console box.

CAUTION

in To reduce the chance of case of an accident or a sudden stop, always keep the auxiliary box closed while driving.

injury

139

Type B

2000 Corolla(U)

Cup holders

Floor mat

The cup holder is designed for holding cups or drink- cans securely its holes. Front: To use the holders, push the lid and pull it out completely. Rear: To use the holder, pull it out.

in

CAUTION

(cid:1) Do not place anything else other than cups or drink- cans on the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

(cid:1) To reduce the chance of injury in case of an accident or a sudden stop while driving, keep the cup holder closed when it is not in use.

Use a floor mat of the correct size. If the floor carpet and floor mat have a hole, then it is designed for use with a locking clip. Fix the floor mat with locking clip into the hole in the floor carpet.

Front

Rear

140

2000 Corolla(U)

CAUTION

Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and the movement of the pedals during driv- ing, it may cause an accident.

interferes with

141

2000 Corolla(U)

142

2000 Corolla(U)

SECTION 7- 1

DO- IT- YOURSELF MAINTENANCE Introduction Engine compartment overview Fuse locations Do- it- yourself service precaution Parts and tools

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

200
201
202
203

199

2000 Corolla(U)

1. Power steering fluid reservoir 2. Engine oil level dipstick 3. Engine oil filler cap 4. Brake fluid reservoir 5. Fuse blocks 6. Battery 7. Engine coolant reservoir 8. Electric cooling fans 9. Windshield washer fluid tank

Engine compartment overview

200

2000 Corolla(U)

Fuse locations

Spare fuses

201

2000 Corolla(U)

Do- it- yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do- it- yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This section gives for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do- it- yourself maintenance, see “Parts and tools”. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:

instructions only

202

CAUTION

(cid:1) When the engine is running, keep hands, clothing, and tools away from the moving fan and engine drive rings, watches, and ties is advisable.)

(Removing

belts.

(cid:1) Right after driving,

the engine compartment—the engine, radiator, exhaust manifold and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot.

(cid:1) If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.

(cid:1) Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable. (cid:1) Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid. (cid:1) Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

(cid:1) Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.

(cid:1) Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. (cid:1) Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.

(cid:1) Do not

leave used oil within the

reach of children.

2000 Corolla(U)

(cid:1) Do not overfill automatic transmis- sion fluid, or the transmission could be damaged.

(cid:1) Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

(cid:1) Be careful not to scratch the glass

surface with the wiper frame.

(cid:1) When closing the engine hood, check to see that you have not for- gotten any tools, rags, etc.

(cid:1) Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

NOTICE

(cid:1) Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.

(cid:1) Add only demineralized or distilled water to fill the radiator. And if you spill some of the coolant, be sure to wash off with water to prevent it from damaging the parts or paint.

(cid:1) Do not allow dirt or anything else to fall through the spark plugholes. (cid:1) Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

(cid:1) Do not reuse iridium-tipped spark

plugs by cleaning or regapping.

Parts and tools Here is a list of parts and tools you will need on performing do- it- yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. Checking the engine oil level Parts (if level is low): API (cid:1) Engine

SJ, “Energy- Conserving” ILSAC multigrade having viscosity proper for your climate

grade or

oil

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding oil) Checking the engine coolant level Parts (if level is low): (cid:1) “TOYOTA Long Life Coolant” or equiva-

lent See Section 7- 2 for details about cool- ant type selection.

(cid:1) Demineralized or distilled water Tools: (cid:1) Funnel (only for adding coolant)

203

2000 Corolla(U)

Checking and replacing fuses Parts (if replacement is necessary): (cid:1) Genuine Toyota fuse or equivalent with

same amperage rating as original

Adding washer fluid Parts: (cid:1) Water (cid:1) Washer fluid containing antifreeze (for

winter use)

Tools: (cid:1) Funnel Replacing light bulbs Parts: (cid:1) Bulb with same number and wattage rating as original (See charts in “Re- placing light bulbs” in Section 7- 3.)

Checking brake fluid Parts (if level is low): (cid:1) SAE J1703 or FMVSS No.116 DOT 3

brake fluid

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding fluid) Checking power steering fluid Parts (if level is low): (cid:1) Automatic

transmission

DEXRON(cid:2)II or III

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding fluid) Checking battery condition Tools: (cid:1) Warm water (cid:1) Baking soda (cid:1) Grease (cid:1) Conventional wrench

(for

clamp bolts)

204

fluid

Tools: (cid:1) Screwdriver

terminal

2000 Corolla(U)

SECTION 7- 2

DO- IT- YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking brake fluid Checking power steering fluid Checking tire pressure Checking and replacing tires Rotating tires Installing snow tires and chains Replacing wheels Aluminum wheel precautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

206
207
208
209
210
211
212
213
214
214

205

2000 Corolla(U)

If the oil level is below or only slightly above the low level, add engine oil of the same type as already in the engine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. The approximate quantity of oil needed to fill between the low level and the full level on the dipstick is indicated below for ref- erence. When the level reaches within the correct