2010 Toyota Avalon Owners Manual

2-3. Operating the lights and windshield wipers

■The windshield wiper and washer can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position.

■Dripping prevention wiper sweep

After washing and wiping operation several times, the wipers operate one more time after a short delay to prevent dripping. However, the last sweep will not happen if the vehicle is traveling above 106
mph (170 km/h).

■Effects of vehicle speed on wiper operation

Vehicle speed affects the following even when the wipers are not in “AUTO” mode. ●Intermittent wiper interval ( ●Wiper operation when the washer is being used (delay until drip preven-

mode)

tion wiper sweep occurs)

With low speed mode, wiper operation will be switched from low speed to intermittent wiper operation only when the vehicle is stationary.

■Rain drop sensor (vehicles equipped with the raindrop detection wind-

shield wipers)

The sensor judges the amount of rain- drops.

163

AVALON_U (OM41437U)

2-3. Operating the lights and windshield wipers

■If no windshield washer fluid sprays

Check that the washer nozzles are not blocked if there is washer fluid in the windshield washer fluid reservoir.

■In extremely hot or cold weather (vehicles equipped with the raindrop

detection windshield wipers) Even if the wiper lever is in “AUTO” mode, the system will switch to intermit- tent operations when the system malfunctions. However, when the windshield gets extremely hot (at more than 194°F [90°C]) or extremely cold (at less than 14°F [-10°C]), the wipers do not oper- ate even if the wiper lever is in “AUTO” mode.

■Customization that can be configured at Toyota dealer

Settings (e.g. drip prevention function) can be changed. (Customizable features →P. 457)

CAUTION

■Caution regarding the use of windshield wipers in “AUTO” mode

The windshield wipers may operate unexpectedly if the sensor is touched or the windshield is subject to vibration in “AUTO” mode. Take care that your fingers or anything else do not become caught in the windshield wipers.

NOTICE

■When the windshield is dry

Do not use the wipers, as they may damage the windshield.

■When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

164

AVALON_U (OM41437U)

2-4. Using other driving systems Cruise control

Use the cruise control to maintain a set speed without using the accelerator.

Indicator Cruise control switch

■ Set the vehicle speed STEP 1

STEP 2

Press the “ON-OFF” button to operate the cruise control.

Push the button once more to deactivate the cruise control.

Accelerate or decelerate to the desired speed and press the lever down to set the cruise control speed.

165

AVALON_U (OM41437U)

2-4. Using other driving systems

■ Adjusting the speed setting

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pressing the lever up or down and releasing it.

■ Canceling and resuming regular acceleration

the brake pedal

Cancel Pull the lever towards you to cancel cruise control. The setting is also canceled when is depressed. Resume To resume cruise control and return to the set speed, push the lever up.

■Cruise control can be set when

●The shift lever is in the “D” or “4”, “5”, or “6” range of “S” mode. ●Vehicle speed is between approximately 25 mph (40 km/h) and 125 mph

(200 km/h). ■Accelerating

The vehicle can be accelerated normally. After acceleration, the set speed resumes.

166

AVALON_U (OM41437U)

2

2-4. Using other driving systems

■Automatic cruise control cancelation

The set speed is automatically canceled in any of the following situations. ●Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed At this time, the memorized set speed is not retained.

●Actual vehicle speed is below 25 mph (40 km/h) ●VSC is activated

■If the cruise control indicator light flashes

Turn the “ON-OFF” button off once, and then reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

CAUTION

■To avoid operating the cruise control by mistake

Keep the “ON-OFF” button off when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause seri- ous or fatal accident. ●In heavy traffic ●On roads with sharp bends ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

Vehicle speed may exceed the set speed when driving down a steep hill.

●On winding roads

167

AVALON_U (OM41437U)

2-4. Using other driving systems Dynamic laser cruise control∗

Dynamic laser cruise control supplements conventional cruise con- trol with a vehicle-to-vehicle distance control. In the vehicle-to-vehi- cle distance control mode, the vehicle automatically accelerates or decelerates in order to maintain a set following distance from vehi- cles ahead.

Indicator Display Cruise control switch Distance switch

∗: If equipped

168

AVALON_U (OM41437U)

■ Set the vehicle speed STEP 1

2-4. Using other driving systems

Press the “ON-OFF” button to operate the cruise control.

Push the button once more to deactivate.

STEP 2

Accelerate or decelerate to the desired speed and press the lever down to set.

169

AVALON_U (OM41437U)

2-4. Using other driving systems

■ Selecting conventional constant speed control mode

Press the “ON-OFF” button to operate the cruise con- trol. Switch to constant speed control mode. (Push and hold for approxi- mately 1 second.) Push the button once more to deactivate. Vehicles with smart key sys- tem: Vehicle-to-vehicle dis- tance control mode is always reset when “ENGINE START STOP” switch is turned to IGNITION ON mode. Vehicles without smart key system: Vehicle-to-vehicle dis- tance control mode is always reset when the engine switch is turned to the “ON” position.

the

170

AVALON_U (OM41437U)

2

■ Adjusting the speed setting

2-4. Using other driving systems

Increase speed Decrease speed Hold the lever until the desired speed setting is displayed. In the constant speed control mode, fine adjustment of the set speed (approximately 1.0
mph [1.6 km/h]) can be made by lightly pressing the lever up or down and releasing it.

■ Canceling and resuming the speed setting

the brake pedal

Cancel Pull the lever towards you to cancel cruise control. The setting is also canceled when is depressed. Resume To resume cruise control and return to the set speed, push the lever up.

171

AVALON_U (OM41437U)

2-4. Using other driving systems

■ Changing the vehicle-to-vehicle distance

the switch Each push of changes the vehicle-to-vehicle distance Long Medium Short Vehicles with smart key sys- tem: The vehicle-to-vehicle distance is automatically set to the the “ENGINE STOP” switch is turned to IGNITION ON mode. Vehicles without smart key system: The vehicle-to-vehicle distance is automatically set to the the engine switch is turned to the “ON” position. A vehicle mark is displayed ahead if one is detected.

long mode when

long mode when

START

172

AVALON_U (OM41437U)

2-4. Using other driving systems

Cruising in vehicle-to-vehicle distance control mode

This mode employs a laser radar sensor to detect the presence of vehicles within 400 ft. (120 m) ahead and to judge the distance between your vehicle and those vehicles.

Note that vehicle-to-vehicle distance will close when traveling on long downhill slopes.

Example of constant speed cruising When there are no vehicles ahead The vehicle travels at the speed set by the driver. The desired vehicle-to- vehicle distance can also be set by operating the vehicle-to-vehicle dis- tance switch. Example of deceleration cruising When the vehicle ahead is driving slower than the set speed When a vehicle is detected running ahead of you, in the same lane, the system automatically decelerates your vehicle. When a greater reduction in vehicle speed is necessary, the system applies the brakes. A warning tone warns you when the system cannot decelerate sufficiently to prevent your vehicle from closing on the vehicle ahead.

173

AVALON_U (OM41437U)

2-4. Using other driving systems

Example of follow-up cruising When following a vehicle driving slower than the set speed The system continues follow-up cruising while adjusting for changes in the speed of the vehicle ahead in order to maintain the vehicle-to-vehicle dis- tance set by the driver. Example of acceleration When there are no longer vehicles driving slower than the set speed in the lane ahead When the vehicle ahead of you executes a lane change, the system slowly accelerates until the set vehicle speed is reached. The system then returns to fixed speed cruising.

Approach warning

When your vehicle is too close to a vehicle ahead, and sufficient automatic deceleration via the cruise control is not possible, the dis- play will flash and buzzer will sound to alert the driver. An example of this would be if another driver cuts in front of you while you are follow- ing a vehicle. Apply the brake to ensure an appropriate vehicle-to- vehicle distance.

174

AVALON_U (OM41437U)

2-4. Using other driving systems

■Dynamic laser cruise control warning lights, display and buzzers

Warning lights, display and buzzers are used to indicate a system malfunc- tion or to alert you to the need for caution while driving.

“CRUISE” indicator light Master warning light Warning code

The warning codes indicate the following.

Warning code

Details

Correction procedures

C1

C2

Indicates that the laser radar sensor is dirty or covered with ice.

Indicates that the system is unable to judge the vehi- cle-to-vehicle distance.

E3 (Flashing)

Indicates that a system malfunction has been detected.

Clean the sensor.

• Stop the wiper or switch the wiper to variable inter- mittent operation. • Avoid direct sunlight. • Wait until the weather becomes clear. Turn off and restart the “ENGINE START STOP” switch or the engine switch.

If the same code appears again after implementing the correction procedure, or if the cruise control cannot be set, contact your Toyota dealer.

175

AVALON_U (OM41437U)

2-4. Using other driving systems

■Switching modes

The mode cannot be switched to constant speed control mode if vehicle-to- vehicle distance control mode has been used. The mode also cannot be switched from constant speed control to vehicle-to-vehicle control mode. Turn the system off by pressing the “ON-OFF” button, and turn it on again.

■The dynamic laser cruise can be set when

●The shift lever is in “D” or the “4”, “5” or “6” range of “S” mode. ●Vehicle speed is between approximately 28 mph (45 km/h) and 85 mph

(135 km/h). ■Accelerating

The vehicle can be accelerated normally.

■Automatically canceling vehicle-to-vehicle distance control

Vehicle-to-vehicle distance control driving is automatically canceled in the following situations. ●Vehicle speed falls below 25 mph (40 km/h) ●VSC is activated ●The sensor cannot operate correctly because it is covered in some way Vehicle-to-vehicle distance control driving must be reset by turning the “ON- OFF” button on again. If vehicle-to-vehicle distance control driving is automatically canceled for any other reason, there may be a malfunction in the system. Contact your Toyota dealer.

■Automatically canceling constant speed control

The set speed is automatically canceled in the following situations. ●Actual vehicle speed is more than 10 mph (16 km/h) below the preset

vehicle speed At this time, the memorized set speed is not retained.

●Vehicle speed falls below 25 mph (40 km/h) ●VSC is activated

176

AVALON_U (OM41437U)

2-4. Using other driving systems

■Vehicle-to-vehicle distance settings

Select a distance from the table below. Note that the distances shown corre- spond to a vehicle speed of 55 mph (90 km/h). Vehicle-to-vehicle distance increases/decreases in accordance with vehicle speed.

Distance options

Long Medium Short

Vehicle-to-vehicle distance Approximately 245 ft. (75 m) Approximately 165 ft. (50 m) Approximately 100 ft. (30 m)

■Laser radar sensor

Always keep the sensor clean to ensure that the vehicle-to-vehicle distance con- trol operates properly. (Some obstruc- tions, such as snow, ice or plastic objects, cannot be detected by the obstruction sensor.) Dynamic laser cruise control is canceled if an obstruction is detected.

■Approach warning

In the following instances, there is a possibility that the warning will not occur. ●When the speed of the vehicle ahead matches or exceeds your vehicle’s

speed

●When the vehicle ahead is traveling at an extremely slow speed ●Immediately after the cruise control speed has been set ●At the instant the accelerator is applied

■Certification

This product is a class l laser product complied with 21 C.F.R part 1040.10 and 1040.11.

177

AVALON_U (OM41437U)

2-4. Using other driving systems

CAUTION

■Before using dynamic laser cruise control

Do not overly rely on vehicle-to-vehicle distance control. Be aware of the set vehicle speed. If automatic deceleration/acceleration is not appropriate, adjust the vehicle speed, as well as the distance between your vehicle and vehicles ahead by applying the brakes, etc.

■To avoid operating the dynamic laser cruise control by mistake

Keep the “ON-OFF” button off when not in use.

■Situations unsuitable for dynamic laser cruise control

Do not use dynamic laser cruise control in any of the following situations. Doing so may result in inappropriate control of speed and could cause seri- ous or fatal accident. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●Where there are sudden changes between sharp up and down gradients ●At entrances to expressways ●When weather conditions are bad enough that they may prevent the sen-

sors from functioning correctly (fog, snow, sandstorm, heavy rain, etc.)

●When the approach warning buzzer can be heard often

178

AVALON_U (OM41437U)

2-4. Using other driving systems

CAUTION

■When the laser radar sensor may not be correctly detecting the vehicle

ahead Apply the brakes as necessary when any of the following types of vehicles are in front of you. As the sensor may not be able to correctly detect these types of vehicles, the proximity alarm (→P. 175) will not be activated, and an accident may result. ●Vehicles that cut in suddenly ●Vehicles traveling at low speeds ●Vehicles that are not moving ●Vehicles with small rear ends (trailers with no load on board etc.) ●Motorcycles traveling in the same lane

■Conditions under which the vehicle-to-vehicle distance control may

not function correctly Apply the brakes as necessary in the following conditions as the laser radar sensor may not be able to correctly detect vehicles ahead, and an accident may result. ●When water or snow thrown up by the surrounding vehicles hinders the

functioning of the sensor

●When your vehicle is pointing upwards (caused by a heavy load in the

trunk etc.)

●When the road curves or when the lanes are narrow ●When steering wheel operation or your position in the lane is unstable ●When the vehicle ahead of you decelerates suddenly.

179

AVALON_U (OM41437U)

2-4. Using other driving systems

NOTICE

■To ensure the laser radar sensor functions correctly

Do not do the following to the sensor or grille cover as doing so may cause the sensor not to function correctly and could result in an accident. ●Stick or attach anything to them ●Leave them dirty ●Disassemble or subject them to strong shocks ●Modify or paint them ●Replace them with non-genuine parts

■Handling the laser radar sensor

Observe the following to ensure the cruise control system can function effec- tively. ●Keep the sensor clean at all times.

Clean the sensor with a soft cloth so you do not mark or damage them.

●Do not subject the sensor or surrounding area to a strong impact.

If the sensor moves even slightly off position, the system may malfunction. If the sensor or surrounding area is subject to a strong impact, always have the area inspected and adjusted by a Toyota dealer.

●Do not disassemble the sensor. ●Do not attach accessories or stickers to the sensor, surrounding area. ●Do not modify or paint the sensor.

180

AVALON_U (OM41437U)

2

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

■ Brake assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

■ VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

■ TRAC (Traction Control)

Maintains drive power and prevents the front wheels from spinning when starting the vehicle or accelerating on slippery roads.

When the VSC/TRAC are operating

If the vehicle is in danger of slip- ping, or if the front wheels spin, the slip indicator light flashes to indicate the VSC/TRAC have been engaged.

that

A buzzer (intermittent) sounds to indicate that VSC is operating.

181

AVALON_U (OM41437U)

2-4. Using other driving systems

■Sounds and vibrations caused by the ABS, brake assist, VSC and

TRAC ●A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

●Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.

CAUTION

■The ABS does not operate effectively when

●The limits of tire gripping performance have been exceeded. ●The vehicle hydroplanes while driving at high speed on the wet or slick

road.

■Stopping distance when the ABS is operating on the wet or slick roads The ABS is not designed to shorten the vehicle’s stopping distance. Always maintain a sufficient distance from the vehicle in front of you in the following situations. ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or roads with uneven pavement

182

AVALON_U (OM41437U)

2

2-4. Using other driving systems

CAUTION

■TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC is operating. Do not drive the vehicle in conditions where stability and power may be lost.

■When the VSC is activated

The slip indicator light flashes and a warning buzzer sounds. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes and a buzzer sounds.

■Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recom- mended tire pressure level. The ABS and VSC systems will not function correctly if different tires are fit- ted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

■Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

183

AVALON_U (OM41437U)

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load.

● Stow cargo and luggage in the trunk whenever possible. Be

sure all items are secured in place.

● Be careful to keep the vehicle level. Placing the weight as far

forward as possible helps maintain vehicle balance.

● For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) – (Total weight of occupants) Steps for Determining Correct Load Limit— (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehi- cle’s placard.

(2) Determine the combined weight of the driver and passengers

that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and

luggage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs. (1400 – 750 (5
× 150) = 650 lbs.)

184

AVALON_U (OM41437U)

2-5. Driving information

(6)

(5) Determine the combined weight of luggage and cargo being

loaded on the vehicle. That weight may not safely exceed the available cargo and lug- gage load capacity calculated in Step 4. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 188) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 870 lb. (395
kg), the available amount of cargo and luggage load capacity will be as follows: 870 lb. – 366 lb. = 504 lb. (395 kg –166 kg = 229 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

504 lb. – 388 lb. = 116 lb. (229 kg – 176 kg = 53 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load equaling the combined weight of the occupants who got on later, by an amount. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

185

AVALON_U (OM41437U)

2-5. Driving information

CAUTION

■Things that must not be carried in the trunk

The following things may cause a fire if loaded in the trunk. ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●Do not place cargo or luggage in or on the following locations as the item may get under the brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Instrument panel • Dashboard

●Secure all items in the occupant compartment, as they may shift and

injure someone during an accident or sudden braking.

●Never allow anyone to ride in the trunk. It is not designed for passen- gers. They should ride in their seats with their seat belts properly fas- tened. Otherwise, they are much more likely to suffer death or serious injury, in the event of sudden braking, sudden swerving or an accident.

186

AVALON_U (OM41437U)

2-5. Driving information

CAUTION

■Weight of the load

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

187

AVALON_U (OM41437U)

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 870 lb. (395 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. Even if the number of occupants are within the seating capacity, do not exceed the total load capacity.

■ Towing capacity

Toyota does not recommend towing a trailer with your vehicle.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 354)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

188

AVALON_U (OM41437U)

2

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires.

189

AVALON_U (OM41437U)

2-5. Driving information

■ Before driving the vehicle

Perform the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to “P” without setting the parking brake. The parking brake may freeze up, preventing it from being released.

190

AVALON_U (OM41437U)

2

2-5. Driving information

Selecting snow chains

Use the correct snow chain size when mounting the snow chains. Chain size is regulated for each tire size.

Side chain:

0.12 in. (3.0 mm) 1.18 in. (30.0 mm) 0.39 in. (10.0 mm)

Cross chain:

0.16 in. (4.0 mm) 0.98 in. (25.0 mm) 0.55 in. (14.0 mm)

Regulations on the use of snow chains

● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

● Install the chains on the front tires. ● Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

■Snow chain installation

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires only. ●Install tire chains following the instructions provided in the accompanying

instructions.

191

AVALON_U (OM41437U)

2-5. Driving information

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified for your vehicle. ●Maintain the specified level of tire inflation pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Snow tires should be installed on all wheels.

192

AVALON_U (OM41437U)

2

2-5. Driving information

CAUTION

■Driving with snow chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used, or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

■Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

193

AVALON_U (OM41437U)

2-5. Driving information Trailer towing

Toyota does not recommend towing a trailer with your vehicle. Toy- ota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for the use of tow hitch mounted carriers.

194

AVALON_U (OM41437U)

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

195

AVALON_U (OM41437U)

2-5. Driving information

196

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger Automatic air conditioning system

Airflow and outlets are automatically adjusted according to the tem- perature setting.

Without navigation system

With navigation system

Windshield defogger

Driver’s side temperature control

Automatic mode

Passenger’s side temperature control

Off

Dual operation

Changes the air outlets used

Fan speed

Air conditioning ON/OFF switch

Outside air or recirculated mode

This illustration is a vehicle equipped with the outside rear view mirror defoggers.

198

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

Using the automatic mode

STEP 1

STEP 2

Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting. Press “∧” to increase the temperature and “∨” to decrease the temperature on The temperature for the driver and passenger seats can be set sep- arately.

Adjusting the settings

■ Adjusting the temperature setting

Press “∧” to increase the temperature and “∨” to decrease the tem- perature on

Press “∧” (increase) or “∨” (decrease) on to separately adjust the temperature for the passenger and driver sides (dual mode). Press to return the driver and passenger side temperatures to the

same setting (simultaneous mode). The air conditioning system switches between dual and simultaneous modes each time

is pressed.

■ Adjusting the fan speed

Press “∧” (increase) or “∨” (decrease) on the Press

to turn the fan off.

switch.

199

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

■ Changing the air outlets

Press

The air outlets switch each time the button is pressed. The air flow shown on the display indicate the following.

Air flows to the upper body.

Air flows to the upper body and feet.

200

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

Air flows to the feet.

Air flows to the feet and the windshield defogger operates.

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (indicator off) and recircu- lated air mode (indicator on) modes each time the button is pressed.

201

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

Defogging the windshield

Press

The air conditioning system con- trol operates automatically.

202

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Center outlets

Turn the knob to open or close the vent Direct air flow to the left or right

Turn the knob to open or close the vent Direct air flow to the left or right

Turn the knob to open or close the vent Direct air flow to the left or right

203

Side outlets

Rear seat outlets

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

■Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. ●Immediately after the switch is pressed, the fan may stop for a while until

warm or cool air is ready to flow.

●Cool air may flow to the area around the upper body when the heater is

on.

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

■Switching between outside air and recirculated air modes

Recirculated air mode or outside air mode may be automatically switched to in accordance with the temperature setting and the inside temperature.

■Window defogger feature

Recirculated air mode may automatically switch to outside air mode in situa- tions where the windows need to be defogged. ■Outside temperature approaches 32°F (0°C)

The air conditioning system may not operate even when pressed.

is

■When the indicator light on

flashes

Press and turn off the air conditioning system before turning it on once more. There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

• It is recommended that the air conditioning system be set to outside air

mode prior to turning the vehicle off.

• The start timing of the blower may be delayed for a short period of time immediately after the air conditioning system is started in automatic mode.

204

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

CAUTION

■To prevent the windshield from fogging up

Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the automatic air conditioning system on longer than necessary when the engine is not running.

205

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger Using the steering wheel climate control switches

Some air conditioning feature can be controlled using the switches on the steering wheel.

Temperature control Automatic mode Off

Using the automatic mode

STEP 1

Press

The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the tempera- ture setting.

STEP 2

Press “∧” to increase the temperature and “∨” to decrease the temperature on

The temperature for the driver and passenger seats can be set separately.

206

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

Adjust the temperature settings

Press “∧” to increase the temperature and “∨” to decrease the tem- perature on

Press “∧” (increase) or “∨” (decrease) on to separately adjust the temperature for the passenger and driver sides (dual mode). Press to turn off the dual mode and to return the driver and passenger

side temperatures to the same setting (simultaneous mode). This function will be canceled when pushed.

on the instrument panel is

Turning off the fan

Press

AVALON_U (OM41437U)

207

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers

These features are used to defog the rear window, and to remove raindrops, dew and frost from the outside rear view mirrors.

With outside rear view mir- ror defoggers Without outside rear view mirror defoggers

Press the button to turn on the rear window (and outside rear view mirror) defoggers. The defoggers will automatically turn off after approximately 15 min- utes. Pressing the button again also turns the defoggers off.

The operation time changes according to the ambient tem- perature and vehicle speed.

■Operating conditions

Vehicles with smart key system

The “ENGINE START STOP” switch must be in IGNITION ON mode.

Vehicles without smart key system

The engine switch must be in the “ON” position.

208

AVALON_U (OM41437U)

3-1. Using the air conditioning system and defogger

CAUTION

■When the outside rear view mirror defoggers are on (if equipped)

Do not touch the rear view mirror surfaces, as they can become very hot and burn you.

NOTICE

■To prevent battery discharge

Turn the defoggers off when the engine is not running.

209

AVALON_U (OM41437U)

3-2. Using the audio system Audio system type

CD player with changer and AM/FM radio

The audio system appearance may differ slightly for vehicles not equipped with JBL brand audio system.

Title

Using the radio Using the CD player Playing MP3 and WMA discs Optimal use of the audio system Using the AUX adapter Using the steering wheel audio switches

Page P. 213
P. 220
P. 228
P. 236
P. 238
P. 239

210

AVALON_U (OM41437U)

3-2. Using the audio system

■Using cellular phones

Interference may be heard through the audio system’s speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

CAUTION

■For vehicles sold in the U.S.A. and Canada

●Part 15 of the FCC Rules

FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

●Laser products

• Do not take this unit apart or attempt to make any changes yourself.

This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

NOTICE

■To prevent battery discharge

Do not leave the audio system on longer than necessary with the engine off.

■To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

211

AVALON_U (OM41437U)

3-2. Using the audio system Audio cover

Press to open.

CAUTION

■When opening or closing the audio cover

Do not jam your hands in the cover.

NOTICE

■To avoid damaging the audio cover or CD

●Do not hold the cover while it is opening. ●Do not close the audio cover before removing an ejected CD.

212

AVALON_U (OM41437U)

3-2. Using the audio system Using the radio

Press

or

to choose an AM or FM band.

Seek frequency

Station selector

Change the program type

Power

Volume

AM⋅SAT/FM mode buttons

Adjust the frequency (AM, FM mode) or channel (SAT mode)

Scan for receivable stations

Setting station presets (excluding XM® Satellite Radio)

STEP 1

Search for desired stations by turning

or pressing “∧”

or “∨” on

STEP 2

Press and hold one of the preset stations (1 - 6) until you hear a beep.

213

AVALON_U (OM41437U)

3-2. Using the audio system

Scanning radio stations (excluding XM® Satellite Radio)

■ Scanning the preset radio stations

STEP 1

Press and hold until you hear a beep. Preset stations will be played for 5 seconds each. When the desired station is reached, press the button again.

STEP 2
■ Scanning all radio stations within range

STEP 1

STEP 2

Press All stations with reception will be played for 5 seconds each. When the desired station is reached, press the button again.

214

AVALON_U (OM41437U)

3-2. Using the audio system

XM® Satellite Radio (if equipped) ■ Receiving XM® Satellite Radio

STEP 1

Press

until “SAT” shows in the display.

The display changes as follows each time the button is pressed. “AM” → “SAT1” → “SAT2” → “SAT3”

STEP 2

Turn

to select a desired channel from all the categories

or press “∧” or “∨” on the current category.

to select a desired channel in

215

AVALON_U (OM41437U)

3-2. Using the audio system

■ Presetting XM® Satellite Radio channels

Select the desired channel. Press and hold the button (1 - 6) until you hear a beep.

■ Changing the channel category

Press “∧” or “∨” on

■ Scanning XM® Satellite Radio channels

● Scanning channels in the current category

STEP 1

STEP 2

Press When the desired channel is reached, press the button again.

● Scanning preset channels

STEP 1

STEP 2

Press and hold When the desired channel is reached, press the button again.

until you hear a beep.

■ Displaying text information

Press The display will show up to 12 characters. The display changes as follows each time the button is pressed. ● CH NAME ● TITLE (SONG/PROGRAM TITLE) ● NAME (ARTIST NAME/FEATURE) ● CH NUMBER

216

AVALON_U (OM41437U)

3-2. Using the audio system

■When the battery is disconnected

All preset stations are erased.

■Reception sensitivity

●Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc.

●The radio antenna is mounted inside the rear window. To maintain clear radio reception, do not attach metallic window tinting or other metallic objects to the antenna wire mounted inside the rear window.

■Receiving XM® Satellite Radio

An XM® Satellite Radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 con- tiguous states and 10 Canadian provinces. ●XM® subscriptions

For detailed information about XM® Satellite Radio or to subscribe: U.S.A– Visit on the web at www.xmradio.com or call 1-800-967-2346. Canada– Visit on the web at www.xmradio.ca or call 1-877-438-9677.

●Radio ID

You will need the radio ID when activating XM® service or reporting a

problem. Select “CH000” using number will appear.

, and the receiver’s 8-character ID

●Satellite tuner

The tuner supports only Audio Services (Music and Talk) and the accom- panying Text Information of XM® Satellite Radio.

217

AVALON_U (OM41437U)

3-2. Using the audio system

■If the satellite radio does not operate normally

If a problem occurs with the XM® tuner, a message will appear on the dis- play. Refer to the table below to identify the problem, and take the suggested corrective action.

ANTENNA

UPDATING

NO SIGNAL

LOADING

OFF AIR

-----

The XM® antenna is not connected. Check whether the XM® antenna cable is attached securely. There is a short-circuit in the antenna or the sur- rounding antenna cable. See a Toyota certified dealer. You have not subscribed to XM® Satellite Radio. The radio is being updated with the latest encryp- tion code. Contact XM® Satellite Radio for sub- scription information. When a contract is canceled, you can choose “CH000” and all free-to-air chan- nels. The premium channel you selected is not autho- rized. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. If you want to listen to the premium chan- nel, contact XM® Satellite Radio. The XM® signal is too weak at the current location. Wait until your vehicle reaches a location with a stronger signal. The unit is acquiring audio or program information. Wait until the unit has received the information. The channel you selected is not broadcasting any programming. Select another channel. There is no song/program title or artist name/fea- ture associated with the channel at that time. No action needed.

218

AVALON_U (OM41437U)

3-2. Using the audio system

---

The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel.

Contact the XM® Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 438-9677 (Canada).

■Certifications for the radio tuner

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by trying one or more of the following: ●Reorienting or relocating the receiving antenna. ●Increasing the separation between the equipment and receiver.