3-6. Other interior features
Pull down the rear seat center armrest.
Open (push down the handle) Lock with the mechanical key or the master key Unlock with the mechanical key or the master key
Trunk storage extension
CAUTION
n While driving
l To avoid injury, always return the cargo hooks to their positions when they
are not in use.
l Always keep the trunk storage extension doors closed to reduce the
chance of injury in case of accident or sudden stop.
NOTICE
n When closing the trunk
Do not leave the luggage mat lever hooked on the edge of the trunk. The luggage mat may get damaged.
277
AVALON_U_(L/O_0802)
3-6. Other interior features Garage door opener (if equipped)
The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, and other devices.
The garage door opener (HomeLink® Universal Transceiver) is manufac- tured under license from HomeLink®.
Programming the HomeLink® (for U.S.A. owners)
The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.
Indicator Buttons
n Programming the HomeLink®
STEP 1
Point the remote control for the device 1 to 3 in. (25 to 75 mm) from the HomeLink® control but- tons as shown in the illustration. Keep the indicator light on the HomeLink® in view while pro- gramming.
278
AVALON_U_(L/O_0802)
STEP 2
STEP 3
3-6. Other interior features
Press and hold down one of the buttons on the HomeLink® and the button on the transmitter. Continue holding down both but- tons until the HomeLink® indica- tor light changes from a slow blink to a rapid flash. This will take approximately 30 seconds. Test the HomeLink® operation by pressing and holding the newly programmed button for 2 seconds. If programming was successful, the garage door will open and close.
If the rapidly
indicator then
If the garage door does not oper- ate, press and hold the pro- grammed button for at least 3 seconds. light remains flashes solid, your garage door opener is Rolling Code type. Skip STEP 4 and proceed to the section “Programming a Rolling Code system”.
STEP 4
Repeat the steps above to program another device for each of the remaining HomeLink® buttons.
279
AVALON_U_(L/O_0802)
3-6. Other interior features
n Programming a Rolling Code system (for U.S.A. owners)
If your device is Rolling Code equipped, follow the steps under the heading “Programming the HomeLink®” before proceeding with the steps listed below.
STEP 1
STEP 2
STEP 3
STEP 4
Locate the training button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener. Refer to the operation manual supplied with the garage door opener for the location of the training button. Press and release the training button. Press for 5 seconds and release the vehicle’s programmed HomeLink® button twice. The garage door may open. If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door. The ceiling mounted garage door opener motor should now recog- nize the HomeLink® transceiver and operate the garage door. Repeat the steps above to program another rolling code sys- tem for any of the remaining HomeLink® buttons.
n Programming an entry gate (for U.S.A. owners)/Programming
all devices in the Canadian market
STEP 1
STEP 2
STEP 3
STEP 4
Place your transmitter 1 to 3 in. (25 to 75 mm) away from the surface of the HomeLink®. Keep the indicator light on the HomeLink® in view while program- ming. Press and hold the selected HomeLink® button. Repeatedly press and release (cycle) the device’s remote control button for two seconds each until step 4 is completed. When the indicator light on the HomeLink® compatible trans- ceiver starts to flash rapidly, release the buttons.
280
AVALON_U_(L/O_0802)
3-6. Other interior features
STEP 5
STEP 6
Test the operation of the HomeLink® by pressing the newly programmed button. Check to see if the gate/device operates correctly. Repeat the steps above to program another device for each of the remaining HomeLink® buttons.
n Programming other devices
To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance.
n Reprogramming a button
The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the “Basic program- ming” instructions.
Operating the HomeLink®
Press the appropriate HomeLink® button. The HomeLink® indicator light on the HomeLink® transceiver should turn on.
The HomeLink® continues to send a signal for up to 20 seconds as long as the button is pressed.
Erasing the entire HomeLink® memory (all three programs)
Press and hold down the 2 out- side buttons for 20 seconds until the indicator light flashes.
If you sell your vehicle, be sure to erase the programs stored in the HomeLink® memory.
281
AVALON_U_(L/O_0802)
3-6. Other interior features
n Before programming
Install a new battery in the transmitter.
l The battery side of the transmitter must be pointed away from the
HomeLink®.
n Certification for the garage door opener
This device complies with Part 15 of the FCC Rules and with RSS-210 of the IC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party respon- sible for compliance could void the user’s authority to operate the device.
CAUTION
n When programming a garage door or other remote control device
The garage door may operate, so ensure people and objects are out of dan- ger to prevent potential harm.
n Conforming to federal safety standards
Do not use the HomeLink® Compatible Transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards. This includes any garage door that cannot detect an obstruction object. A door or device without these features increases the risk of death or serious injury.
282
AVALON_U_(L/O_0802)
3-6. Other interior features Compass (if equipped)
The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. n Operation
To turn the compass on or off, press the switch.
n Displays and directions
Display
NE SE SW NW
Direction
North
Northeast
East
Southeast
South
Southwest
West
Northwest
283
AVALON_U_(L/O_0802)
3-6. Other interior features
Calibrating the compass
Samoa: 5 Guam: 8 Saipan: 8
The direction display deviates from the true direction determined by
the earth’s magnetic field. The amount of deviation varies according
to the geographic position of the vehicle.
If you cross over a map boundary shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to the following.
n Deviation calibration
STEP 1
Stop the vehicle where it is safe to drive in a circle.
STEP 2
Press the switch until a number (1 to 15) appears on the com- pass display.
STEP 3
Press the switch, and referring to the map above, select the number of the zone where you are.
284
AVALON_U_(L/O_0802)
3-6. Other interior features
STEP 4
Wait a few seconds until the compass direction is displayed. The calibration is complete.
n Circling calibration
If “CAL” appears on the display, drive the vehicle at 5 mph (8 km/ h) or less in a circle until a direc- tion is displayed.
If there is not enough space to drive in a circle, drive around the block until the direction is dis- played.
n Conditions unfavorable to correct operation
The compass may not show the correct direction in the following conditions: l The vehicle is stopped immediately after turning. l The vehicle is on an inclined surface. l The vehicle is in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).
l The vehicle has become magnetized.
(There is a magnet or metal object near the inside rear view mirror.)
l The battery has been disconnected. l A door is open.
285
AVALON_U_(L/O_0802)
3-6. Other interior features
CAUTION
n While driving
Do not adjust the display. Be sure to adjust the display only when the vehicle is stopped.
n When doing the circling calibration
Be sure to secure a wide space, and watch out for people and vehicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.
NOTICE
n To avoid the compass malfunctions
Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause a malfunction of the compass sensor.
n To ensure normal operation of the compass
l Do not perform circling calibration of the compass in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields. l During calibration, do not operate electric systems (moon roof, power win-
dows, etc.) as they may interfere with the calibration.
286
AVALON_U_(L/O_0802)
4-1. Maintenance and care Cleaning and protecting the vehicle exterior
Perform the following to protect the vehicle and maintain it in prime condition.
l Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. Wash the vehicle body using a sponge or soft cloth, such as a cham- ois.
l For hard-to-remove marks, use car wash soap and rinse thor-
oughly with water.
l Wipe away any water. l Wax the vehicle when the waterproof coating deteriorates. If water does not bead on a clean surface, apply wax when the vehicle body is cool.
288
AVALON_U_(L/O_0802)
4-1. Maintenance and care
n Automatic car washes
l Fold the mirrors back before washing the vehicle. l Brushes used in automatic car washes may scratch the vehicle surface
and harm your vehicle’s paint.
n High pressure car washes
Do not allow the nozzles of the car wash to come within close proximity of the windows. Before car wash, check that the fuel filler door is closed.
n Aluminum wheels
Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.
n Bumpers and side moldings
Do not scrub with abrasive cleaners.
n To prevent paint deterioration and corrosion on the body
l Wash the vehicle immediately in the following cases:
• After driving near the sea coast • After driving on salted roads • If you see coal tar or tree sap on the paint surface • If you see dead insects, insect droppings or bird droppings on the paint • After driving in an area contaminated with soot, oily smoke, mine dust,
iron powder or chemical substances
• If the vehicle becomes heavily soiled in dust or mud • If liquids such as benzine and gasoline are spilled on the paint surface If the paint is chipped or scratched, have it repaired immediately.
289
AVALON_U_(L/O_0802)
4-1. Maintenance and care
CAUTION
n Caution about the exhaust pipe
Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.
NOTICE
n To protect your vehicle’s painted surfaces
Do not use organic cleaners such as benzine or gasoline.
n Cleaning the exterior lights
l Wash carefully. Do not use organic substances or scrub with a hard brush.
This may damage the surfaces of the lights.
l Do not apply wax on the surface of the lights. Wax may cause damage to
the lenses.
n When using an automatic car wash
(vehicles equipped with the raindrop detection windshield wipers)
OFF
AUTO
Set the wiper switch to OFF. If the wiper switch is in “AUTO”, the wip- ers may operate and the wiper blades may be damaged.
290
AVALON_U_(L/O_0802)
4-1. Maintenance and care Cleaning and protecting the vehicle interior
The following procedures will help protect your vehicle’s interior and keep it in top condition: n Protecting the vehicle interior
Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
n Cleaning the leather areas
l Remove dirt and dust using a vacuum cleaner. l Wipe any excess dirt and dust with a soft cloth dampened with
diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.
l Wring out any excess water from the cloth and thoroughly
wipe off all remaining traces of detergent.
l Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded and venti- lated area.
n Synthetic leather areas
l Remove loose dirt using a vacuum cleaner. l Apply a mild soap solution to the synthetic leather using a
sponge or soft cloth.
l Allow the solution to soak in for a few minutes. Remove the
dirt and wipe off the solution with a clean, damp cloth.
291
AVALON_U_(L/O_0802)
4-1. Maintenance and care
n Cleaning the inside of the rear window
Do not use glass cleaner to clean the rear window, as this may cause dam- age to the rear window defogger heater wires. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires.
n Caring for leather areas
Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.
n Shampooing the carpets
There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. The excellent results are obtained by keeping the carpet as dry as possible.
n Seat belts
Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.
CAUTION
n Water in the vehicle
l Be careful not to splash or spill liquid on the floor. l Do not get any of the SRS components or wiring in the vehicle interior wet.
(→P. 83) Electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or serious injury.
292
AVALON_U_(L/O_0802)
4-1. Maintenance and care
NOTICE
n Cleaning detergents
Do not use the following types of detergent, as they may discolor the vehicle interior or cause streaks or damage to painted surfaces. l Non-seat portions: Organic substances such as benzine or gasoline, alka-
line or acidic solutions, dye, or bleach.
l Seats: Acidic solutions, such as thinner, benzine, or alcohol.
n Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of leather surfaces. l Remove any dust or dirt on leather surfaces immediately. l Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
l Do not place items made of vinyl, plastic, or that contain wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.
n Water on the floor
Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components under the floor of the vehicle, and may also cause the body to rust.
n Cleaning the inside of the rear window
Be careful not to scratch or damage the heater wires or antenna.
293
AVALON_U_(L/O_0802)
4-2. Maintenance Maintenance requirements
To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance. n General maintenance
Should be performed on a daily basis. This can be done by your- self or by a Toyota dealer. n Scheduled maintenance
Should be performed at specified intervals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
n Do-it-yourself maintenance
You can perform some maintenance procedures yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals are recommended. For details about warranty coverage, see the separate “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement”.
n Repair and replacement
It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
294
AVALON_U_(L/O_0802)
4-2. Maintenance
n Allow inspection and repairs to be performed by a Toyota dealer
l Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.
l Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.
CAUTION
n Hazardous materials
l Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
l Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.
l Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 318)
l Used engine oil contains chemicals that have been shown to cause cancer in laboratory animals. Avoid prolonged and repeated contact. Always pro- tect your skin by washing thoroughly with soap and water.
295
AVALON_U_(L/O_0802)
4-2. Maintenance General maintenance
Listed below are the general maintenance items that should be per- formed at the intervals specified in the “Scheduled Maintenance Guide” or “Owner’s” Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.
Check points
(→P. 318) (→P. 315) (→P. 313) (→P. 308)
• Maintenance-free • At the correct level? • At the correct level? • At the correct level? • No fumes or strange sounds? • At the correct level? (→P. 316) • Not blocked with foreign matter? (→P. 314) (→P. 321)
• At the correct level?
Engine compartment
Items
Battery Brake fluid Engine coolant Engine oil Exhaust system Power steering fluid
Radiator/condenser/hoses
Washer fluid
296
AVALON_U_(L/O_0802)
4-2. Maintenance
Vehicle interior
Items
Accelerator pedal
Automatic transmission “Park” mechanism
Brake pedal
Brakes
Head restraints Indicators/buzzers
Lights
Parking brake
Seat belts
Seats
Steering wheel
Check points
• Moves smoothly (without uneven pedal effort or catching)? • Can the vehicle be hold securely on an incline with the shift lever in “P”? • Moves smoothly? • Does it have appropriate clearance and correct amount of free play? • Pulls to one side when applied? • Loss of brake effectiveness? • Spongy feeling brake pedal? • Pedal almost touches floor? • Move smoothly and lock securely? • Function properly? • Do all the lights come on? • Headlights aimed correctly? (→P. 353) • Moves smoothly? • Can hold the vehicle securely on an incline? • Does the seat belt system operate smoothly? • Are the belts undamaged? • Do the seat controls operate properly? • Moves smoothly? • Has correct free play? • No strange noises?
297
AVALON_U_(L/O_0802)
4-2. Maintenance
Vehicle exterior
Items
Check points
Doors/trunk Engine hood Fluid leaks
Tire
• Operate smoothly? • The lock system works properly? • Is there any leakage after parking? • Inflation pressure is correct? • Tire surfaces not worn or damaged? • Tires rotated according to the mainte- nance schedule? • Wheel nuts are not loose?
CAUTION
n If the engine is running
Turn off the engine and ensure that there is adequate ventilation before per- forming maintenance checks.
298
AVALON_U_(L/O_0802)
4-2. Maintenance Emission inspection and maintenance (I/M) programs
Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. n If the malfunction indicator lamp comes on
The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.
n Your vehicle may not pass the I/M test:
l When the battery is disconnected or discharged
Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.
l When the fuel tank cap is loose
The malfunction indicator lamp comes on as a temporary mal- function and your vehicle may not pass the I/M test.
n When the malfunction indicator lamp goes off after several
driving trips The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.
n If your vehicle does not pass the I/M test
Contact your Toyota dealer to prepare the vehicle for re-testing.
299
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance Do-it-yourself service precautions
If you perform maintenance yourself, be sure to follow the correct procedure given in these sections.
Items
Parts and tools
Battery condition
(→P. 318)
Brake fluid level
(→P. 315)
Engine coolant level
(→P. 313)
Engine oil level
(→P. 308)
• Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology. For the U.S.A.: “Toyota Super Long Life Cool- ant” is pre-mixed with 50% cool- ant and 50% deionized water. For Canada: “Toyota Super Long Life Cool- ant” is pre-mixed with 55% cool- ant and 45% deionized water. • Funnel (used only for adding cool- ant) • “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel, funnel (used only for adding engine oil)
300
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Items
Parts and tools
Fuses
Headlight aim
(→P. 344)
(→P. 353)
Power steering fluid level
(→P. 316)
• Fuse with same amperage rating as original • Phillips-head screwdriver • Automatic transmission fluid DEXRON® II or III • Rag or paper towel • Clean funnel
Radiator and condenser
(→P. 314)
⎯
Tire inflation pressure (→P. 331)
Washer fluid
(→P. 321)
• Tire pressure gauge • Compressed air source • Water washer fluid containing anti- freeze (for winter use) • Funnel
CAUTION
The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions. n When working on the engine compartment
l Keep hands, clothing, and tools away from the moving fan and engine
drive belt.
l Be careful not to touch the engine, radiator, exhaust manifold, etc. right
after driving as they may be hot. Oil and other fluids may also be hot.
l Do not leave anything that may burn easily, such as paper or rags, in the
engine compartment.
l Do not smoke, cause sparks or expose an open flame to fuel or the bat-
tery. Fuel and battery fumes are flammable.
l Be extremely cautious when working on the battery. It contains poisonous
and corrosive sulfuric acid.
301
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
CAUTION
n When working near the electric cooling fan or radiator grille
Be sure the “ENGINE START STOP” switch or the engine switch is OFF. With the “ENGINE START STOP” switch or the engine switch in ON mode, the electric cooling fan may automatically start to run if the air conditioning is on and/or the coolant temperature is high. (→P. 314)
n Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in the eyes.
NOTICE
n If you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine wear due to dirt in the air. Also a backfire could cause a fire in the engine compart- ment.
302
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance Hood
Release the lock from the inside of the vehicle to open the hood.
STEP 1
STEP 2
Pull the hood lock release lever.
The hood will pop up slightly.
Lift the hood catch and lift the hood.
CAUTION
n Pre-driving check
Check that the hood is fully closed and locked. If the hood is not locked properly it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
303
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance Positioning a floor jack
When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury.
Front
Rear
304
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
CAUTION
n When raising your vehicle
Make sure to observe the following to reduce the possibility of death or seri- ous injury.
l Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.
l Do not use the jack that was supplied with your vehicle. l Do not put any part of your body or get underneath the vehicle supported
only by the jack. Always use automotive jack stands or a solid, level surface.
l Do not start the engine while the vehicle is supported by the floor jack. l Stop the vehicle on level firm ground, firmly set the parking brake and put
the shift lever in “P”.
l Make sure to set the floor jack properly at the jack point.
Raising the vehicle with an improperly positioned floor jack will damage the vehicle and may cause the vehicle to fall off the floor jack.
l Do not raise the vehicle while someone is in the vehicle. l When raising the vehicle, do not place any objects on top of or underneath
the floor jack.
305
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance Engine compartment
Engine coolant reservoir
(→P. 313)
Power steering fluid reservoir Engine oil filler cap
(→P. 316)
(→P. 309)
Engine oil level dipstick
(→P. 308)
Brake fluid reservoir
(→P. 315)
306
AVALON_U_(L/O_0802)
Fuse box Battery Radiator Electric cooling fans Condenser Washer fluid tank
(→P. 344) (→P. 318) (→P. 314)
(→P. 314)
(→P. 321)
4-3. Do-it-yourself maintenance
Engine compartment cover
n Removing the cover
n Installing the clips
Open Insert Press
307
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Engine oil
With the engine at operating temperature and turned off, check the oil
level on the dipstick.
n Checking the engine oil
STEP 1
Park the vehicle on level ground. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.
STEP 2
Hold a rag under the end and pull the dipstick out.
STEP 3
STEP 4
STEP 5
STEP 6
Wipe the dipstick clean. Reinsert the dipstick fully. Holding a rag under the end, pull the dipstick out and check the oil level. Wipe the dipstick and reinsert it fully. Low Full
308
AVALON_U_(L/O_0802)
n Adding engine oil
4-3. Do-it-yourself maintenance
If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
Make sure to check the oil type and prepare the items needed before adding oil.
Oil grade Oil quantity (Low → Full)
ILSAC multigrade engine oil
1.6 qt. (1.5 L, 1.3 Imp. qt.)
Items
Clean funnel
STEP 1
STEP 2
STEP 3
Remove the oil filler cap. Add engine oil slowly, checking the dipstick. Install the filler cap, turning it clockwise.
309
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n Recommended viscosity
SAE 5W-30 is the best choice for good fuel economy, and good starting in cold weather.
If SAE 5W-30 oil is not available, SAE 10W-30 oil may be used. However, it should be replaced with SAE 5W-30 oil at the next oil change.
Outside temperature
n How to read oil container labels
The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use.
310
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n Engine oil consumption
l The amount of engine oil consumed depends on the oil viscosity, the
quality of the oil and the way the vehicle is driven.
l More oil is consumed under driving conditions such as high speeds, fre-
quent acceleration and deceleration.
l A new engine consumes more oil. l When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accu- rately.
l Oil consumption: Max. 1.1 qt./600 miles, 0.9 lmp.qt./600 miles (1.0 L per 1000 km). If the vehicle consumes more than this amount, contact your Toyota dealer.
n After changing the engine oil (U.S.A.only)
The oil change system should be reset. Perform the following procedures:
STEP 1
Switch the display to the odometer. (→P. 136) Turn the “ENGINE START STOP” switch or the engine switch to the OFF. While pressing the trip meter reset button, turn the “ENGINE START STOP” switch or the engine switch to the ON. Continue to press and hold the button until the trip meter displays 000000.
STEP 2
STEP 3
311
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
CAUTION
n Used engine oil
l Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
l Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
l Do not leave used engine oil within the reach of children.
NOTICE
n To prevent serious engine damage Check the oil level on regular basis.
n When replacing the engine oil
l Be careful not to spill engine oil on the vehicle components. l Avoid overfilling, or the engine could be damaged. l Check the oil level on the dipstick every time you refill the vehicle. l Be sure the engine oil filler cap is properly tightened.
312
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Engine coolant
The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold.
Reservoir cap Full Low If the level is on or below the “L” line, add coolant up to the “F” line.
n If the coolant level drops within a short time after replenishing
Visually check the radiator, hoses, coolant reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system.
n Coolant selection
Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.
U.S.A.: “Toyota Super Long Life Coolant” is a mixture of 50% coolant and
50% deionized water. (Enabled: -31°F [-35°C])
Canada: “Toyota Super Long Life Coolant” is a mixture of 55% coolant
and 45% deionized water. (Enabled: -44°F [-42°C])
For more details about coolant, contact your Toyota dealer.
313
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
CAUTION
n When the engine is hot
Do not remove the radiator cap. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing burns or other injuries.
NOTICE
n When adding the coolant
Coolant is neither plain water not straight antifreeze. The correct mixture of water and anti freeze must be used to provide proper lubrication, corrosion protection and cooling. Be sure to read the antifreeze or coolant label.
n If you spill coolant
Be sure to wash it off with water to prevent it from damaging to parts or paint.
Radiator and condenser
Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer.
CAUTION
n When the engine is hot
Do not touch the radiator or condenser, as they may be hot and you may be burned.
314
AVALON_U_(L/O_0802)
Brake fluid
n Checking fluid level
4-3. Do-it-yourself maintenance
The brake fluid level should be between the “MAX” and “MIN” lines on the tank.
Make sure to check the fluid type and prepare the necessary items. n Adding fluid
Fluid type
Items
FMVSS No.116 DOT 3 or SAE J1703 brake fluid Clean funnel
n Brake fluid can absorb moisture from the air
Excess moisture in the fluid can cause a dangerous loss of braking effi- ciency. Use only newly opened brake fluid.
CAUTION
n When filling the reservoir
Take care because brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets in your eyes, flush your eyes with clean water immediately. If you still experience discomfort, see a doctor.
315
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
NOTICE
n If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious problem.
Power steering fluid
n Fluid level
The fluid level should be within the appropriate range.
Full (when hot) Add fluid (when hot) Full (when cold) Add fluid (when cold)
Hot: The vehicles has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures. (Fluid tem- perature, 140°F - 175°F [60°C - 80°C]).
Cold: The engine has not been run for about 5 hours. (Room tem-
perature, 50°F - 85°F [10°C - 30°C]).
316
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n Checking the fluid level
Make sure to check the fluid type and prepare the necessary items.
Fluid type
Items
Automatic transmission fluid DEXRON® II or III Rag or paper, clean funnel (only for adding fluid)
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
Clean all dirt off the reservoir. Remove the cap by turning it counterclockwise. Wipe the dipstick clean. Reinstall and remove the reservoir cap again. Check the fluid level.
CAUTION
n When checking the reservoir
Take care, as the reservoir may be hot.
NOTICE
n When adding fluid
Avoid overfilling, or the power steering may be damaged.
n After replacing the reservoir cap
Check the steering box case, vane pump and hose connections for leaks or damage.
317
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Battery
Check the battery as follows. n Battery exterior
Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.
Terminals Hold-down clamp
n Checking battery condition
Check the battery condition by the indicator color.
Type A Green
Dark
Type B Blue
White
Clear or light yellow
Red
Good condition Charging necessary. Have the battery checked by your Toyota dealer. Not working properly, have the battery checked by your Toy- ota dealer.
318
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n Before recharging
When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging:
If recharging with the battery installed on the vehicle, be sure to discon- nect the ground cable.
l Make sure the power switch on the charger is off when connecting and
disconnecting the charger cables to the battery.
319
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
CAUTION
n Chemicals in the battery
A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near bat- tery: l Do not cause sparks by touching the battery terminals with tools. l Do not smoke or light a match near the battery. l Avoid contact with eyes, skin and clothes. l Never inhale or swallow electrolyte. l Wear protective safety glasses when working near the battery. l Keep children away from the battery.
n Where to safety charge the battery
Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation.
n How to recharge the battery
Only perform a slow charge (5A or less). The battery may explode if charged at a quicker rate.
n Emergency measures regarding electrolyte
If electrolyte gets in your eyes Flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility. If electrolyte gets on your skin Wash the affected area thoroughly. If you feel pain or a burning sensation, seek medical attention immediately. If electrolyte gets on your clothes It can soak through clothing on to your skin. Immediately take off the cloth- ing and follow the procedure above if necessary. If you accidentally swallow electrolyte Drink a large quantity of water or milk. Follow with milk of magnesia, beaten raw egg or vegetable oil. Get emergency medical attention immedi- ately.
320
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
NOTICE
n When recharging the battery
Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.
Washer fluid
If any washer does not work or the low washer fluid warning light comes on, the washer tank may be empty. Add washer fluid.
CAUTION
n When refilling the washer fluid
Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc.
NOTICE
n Do not use any fluid other than washer fluid
Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces.
n Diluting washer fluid
Dilute washer fluid with water as necessary. Refer to the freezing temperatures listed on the washer fluid tank.
321
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance Tires
Replace or rotate tires in accordance with maintenance sched- ules and treadwear. n Checking tires
location of
New tread Treadwear indicator Worn tread The treadwear indicators is shown by the “TWI” or “∆” marks, etc., molded on the sidewall of each tire. Check spare tire condition and inflation pressure if not rotated.
Rotate the tires in the order shown.
To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is carried out at the same inter- val as tire inspection. Do not fail to initialize the tire pressure warning system after tire rotation.
n Tire rotation
Front
322
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n The tire pressure warning system
Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 373)
Installing tire pressure warning valves and transmitters
When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed. When new tire pressure warning valves and transmitters are installed, new tire pressure warning valve and transmitter ID codes must be registered in the tire pressure warning computer and tire pressure warning system must be initialized. Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer.
Initializing the tire pressure warning system
n The tire pressure warning system must be initialized in the fol-
lowing circumstances: l When rotating the tires on vehicles differing with front and rear
tire inflation pressures.
l When changing the tire inflation pressure by changing traveling
speed or load weight, etc.
When the tire pressure warning system is initialized, the current tire inflation pressure is set as the pressure benchmark.
323
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n How to initialize the tire pressure warning system
STEP 1
Park the vehicle in safe place and turn the “ENGINE START STOP” switch or the engine switch to OFF mode. While the vehicle is moving, initialization is not performed. Adjust the tire inflation pressure to the specified cold tire infla- tion pressure level. (→P. 412) Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level. Turn the “ENGINE START STOP” switch or the engine switch to ON mode.
STEP 2
STEP 3
STEP 4
Push and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times.
STEP 5
Wait for a few minutes with the ON mode, and then turn the “ENGINE START STOP” switch or the engine switch to OFF mode.
324
AVALON_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Registering ID codes
The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.
n When to replace your vehicle’s tires
Tires should be replaced if: l You have tire damage such as cuts, splits, cracks deep enough to
expose the fabric or bulges indicating internal damage
l A tire goes flat repeatedly or cannot be properly repaired due to the
size or location of a cut or other damage
If you are not sure, consult with your Toyota dealer.
n Replacing tires and wheels