To turn on or off the lights automatical-
ly, twist the headlight/turn signal lever
knob to the position 3 (“AUTO”) when
the ignition key is in the “ON” position.
The headlights and/or all of the lights in
position 1 automatically turn on or off de-
pending on the darkness of the surround-
ings.
Manually twist the knob to the position 2
to turn on the headlights if they are need-
ed immediately when entering a dark tun-
nel, parking structure, etc.
104
top of
the driver’s side
The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. Automatic light cut off system Position 1 or position 3 with the tail lights on— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position.
Position 2 or position 3 with the head-
lights on—
The lights automatically turn off after 30
seconds when any of the door or trunk lid
is opened and closed with the ignition key
in the “ACC” or “LOCK” position.
Vehicles with wireless remote control sys-
tem—The lights can be turned off immedi-
ately by pushing the “LOCK” switch on the
wireless remote control transmitter with all
the doors locked and the trunk lid closed.
If any of the door or trunk lid is kept
opened, the lights automatically
turn off
after 20 minutes.
To turn on the lights again, turn the igni-
tion key to the “ON” position or actuate
the headlight switch. If you are going to
park for over one week, make sure the
headlight switch is off.
NOTICE
To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Daytime Running Light (DRL) system Daytime Running Light (DRL) System can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many different driving conditions, but they can be espe- cially helpful the short periods after dawn and before sunset. The DRL system will make your headlights come on at a reduced brightness when: D The ignition is on with the engine run-
in
ning.
D The headlight switch is off. D The parking brake is released. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights for night driving.
to full intensity
High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights even when the headlight switch is off.
the lever all
TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” in Section 7−3.
105
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Emergency flashers
Instrument panel light control
NOTICE
To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.
flashers,
turn on
the emergency
To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.
To adjust the brightness of the instru- ment panel lights, turn the knob.
106
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Front fog lights
Interior light
To turn on the front fog lights, twist the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam.
To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns light on when any door is opened. The light goes off when all the doors are closed.
the
ILLUMINATED ENTRY SYSTEM When the switch is in the “DOOR” posi- tion and any door is opened, the light will come on. After all the doors are closed, the light remains on for about 15 seconds before fading out. However, in the following cases, the light goes off immediately. D All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.
D The ignition key is turned to the “ACC” or “ON” after all the doors are closed.
the
transmitter simultaneously,
D All the doors are closed and locked.
When all the doors are unlocked using
either the key or the wireless remote con-
trol
light
will come on and remain on for about 15
seconds, before fading out.
INTERIOR LIGHT CUT OFF OPERATION
To prevent
from being dis-
charged, the light will automatically turn
off when the key is removed and the door
is left opened with the switch at “DOOR”
position for 20 minutes or more.
the battery
107
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Front personal and interior lights
Front personal lights— To turn on the front personal lights, push the switch. To turn the lights off, push the switch once again. Interior lights— The interior lights turn on when any of the door is opened. The lights go off when all of the doors are closed. You cannot turn off the lights when any of the doors is opened.
With moon roof
Without moon roof
108
lights come on when any door
ILLUMINATED ENTRY SYSTEM The is opened. After all the doors are closed, the lights remain on for about 15 seconds and then go out. However, in the following cases, the lights go off immediately. D All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.
D The ignition key is turned to the “ACC” or “ON” after all the doors are closed.
D All the doors are closed and locked. When all the doors are unlocked using either the key or wireless remote control transmitter simultaneously, the lights will come on and remain on for about 15 sec- onds, before fading out. INTERIOR LIGHT CUT OFF OPERATION To prevent from being dis- charged, the lights will automatically turn off when the key is removed and the door is left opened for 20 minutes or more.
the battery
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Rear personal lights
Ignition switch light
the
light comes on
When all the doors are unlocked with the key or wireless remote control transmitter for simultaneously, about 15 seconds and fades out, even if the door is not opened. To prevent from being dis- charged, the light will automatically turn off when the key is removed and the door is left opened for 20 minutes or more.
the battery
then
To turn on the rear personal light, push the switch. To turn the light off, push the switch once again.
For easy access to the ignition switch, the ignition switch light comes on when any of the doors are opened. The light remains on for about 15 seconds after all the doors are closed. However, in the following cases, the light go off immediately. D All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.
D The ignition key is turned to the “ACC” or “ON” after all the doors are closed.
D All the doors are closed and locked.
109
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Windshield wipers and washer
(intermittent operation type)
To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.
Lever position
Position 1
Position 2
Position 3
Position 4
Operation
Intermittent operation Low speed operation High speed operation Washer on
110
the band upward to
The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it. To squirt washer fluid, pull the lever toward you (position 4). If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.
the washer
NOTICE
Do not operate the wipers if the wind- shield is dry. It may scratch the glass or may damage wiper blades.
Windshield wipers and washer
(raindrop detection type)
Automatic control adjuster
To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.
Lever position
Position 1
Position 2
Position 3
Position 4
Operation
Automatic operation Low speed operation High speed operation Washer on
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Even if the wiper lever is in the position 1, the system will switch to intermittent operations in the following conditions: D When
the windshield gets extremely
cold (at less than −10_C [14_F])
if
D When the system malfunctions
However, when
the windshield gets ex-
tremely hot (at more than 90_C [194_F]),
the wipers do not operate even
the
wiper lever is in the position 1.
When the ignition switch is turned off with
the wiper lever in the position 1, and then
the ignition switch is turned on again, the
automatic operation may not work even if
raindrops are on the windshield.
In this case, move the lever to another
position and return it
to the position 1
again.
CAUTION
Be careful not to get your fingers caught between the wipers and wind- shield. When the wiper lever is in the posi- tion 1 with the ignition switch on, the wipers could operate automatically in the following cases: D If you touch the upper center of the
windshield adjacent to the sensor.
D If you wipe the upper center of the windshield (adjacent to which the sensor is located) with a towel or other object.
D If the windshield vibrates. D If you touch the sensor.
NOTICE
Do not apply detergent to or wet the automatic wiper control sensor when cleaning the inside of the windshield.
111
2004 AVALON from Aug. ’04 Prod. (OM41412U)
is determined by
Automatic operation (position 1) The wiper speed the amount of raindrops and sunlight detected by the automatic wiper control sensor. The automatic wiper control sensor is on the the windshield as shown above. If you feel that the operation of the auto- matic wiper control is too fast or too slow, twist the automatic control adjuster in the “−” direction to lower sensitivity, and “+” direction to boost the sensitivity.
inside of
To squirt washer fluid, pull the lever toward you (position 4). If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.
the washer
NOTICE
Do not operate the wipers if the wind- shield is dry. It may scratch the glass or may damage wiper blades.
112
’04 AVALON U (L/O 0408)
Shifting the windshield wiper position
The wiper blades retract under the hood when the wipers are turned off. In the following cases, the wipers should be shifted retracted position (position 2) to the rest position (position 1) above the hood level. D When cleaning the windshield D When inspecting or replacing the wip-
from
the
ers
D When the retraction may be obstructed the bottom of the
by snow, etc., at windshield
than
Other wipers in the retracted position.
the above cases, keep
the
SHIFTING TO THE REST POSITION Hold the connection of the wiper arm and wiper blade and pull it upward for more than 10 cm (3.9 in.) along the windshield glass with force of the about 98 N (10 kgf, 22 lbf).
NOTICE
To prevent the wiper blades from be- ing deformed, be sure to hold the connection of the wiper arm and wip- er blade securely.
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Rear window and outside rear view mirror defoggers
Type A
Type C
TO
THE RETRACTED
RETURNING POSITION Push the connection of the wiper arm and wiper blade downward.
NOTICE
To prevent the wiper blades from be- ing deformed, be sure to hold the connection of the wiper arm and wip- er blade securely.
Type B
To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the surface. An indicator light will illuminate to indicate the defogger is operating. Type C—The heater panels in the outside rear view mirrors will also quickly clear the surfaces. Keep your hands off the mirror faces when the switch is on. Push the switch once again to turn the defoggers off.
113
2004 AVALON from Aug. ’04 Prod. (OM41412U)
The system will automatically shut off af-
ter the defogger has operated about 15
minutes.
CAUTION
Type C—Since the mirror surfaces can get hot, do not touch them when the defogger switch is on.
turn
Make sure you the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow. On some models, if the outside rear view mirrors are heavily coated with ice, use a spray de−icer before operating the switch.
NOTICE
When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.
114
’04 AVALON U (L/O 0408)
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
115
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
SECTION 1− 6
OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers
117
117
118
118
120
116
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Fuel gauge
Engine coolant temperature gauge
If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.
indicates
The gauge the approximate quantity of fuel remaining in the tank when the ignition switch is on. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual.
The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high
speed driving.
117
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Tachometer
Odometer and two trip meters
D Idling for a long period with the air conditioning on in stop−and−go traffic.
D Towing a trailer.
NOTICE
z Do not remove the thermostat
in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.
z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” in Section 4.
118
Type A
The tachometer indicates engine speed in thousands of rpm (revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.
NOTICE
Do not let the indicator needle get into the red zone. This may cause severe engine damage.
Type B
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
3. “ODO/TRIP” button—Resets
the
two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the button. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the button until the meter is set to zero. The same process can be applied for resetting the trip meter B.
to
Type C
trip meters when
This meter displays the odometer and two ignition switch is on. 1. Odometer—Shows
total distance
the
the
the vehicle has been driven.
2. Two
trip meters—Show
two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.
fuel economy and
the other
119
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Service reminder indicators and warning buzzers
If the indicator or buzzer comes on...
Do this.
or
If parking brake is off, stop immediately and contact Toyota dealer.
(indicator and buzzer)
Fasten driver’s seat belt.
Fasten front outside passenger’s seat belt.
Stop and check.
Stop and check.
Take vehicle to Toyota dealer.
Fill up tank.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
120
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
If the indicator or buzzer comes on...
Do this.
(h)
(i)
(j)
(k)
(l)
(m)
(n)
or
Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer.
Close all doors.
Replace bulb.
Take vehicle to Toyota dealer immediately.
Take vehicle to Toyota dealer.
Add washer fluid.
Key reminder buzzer
Remove key.
121
2004 AVALON from Aug. ’04 Prod. (OM41412U)
(a) Brake System Warning Light This light comes on in the following cases when the ignition key is in the “ON” posi- tion. D When the parking brake is applied... This light comes on for a few seconds when to the “ON” position even after the parking brake is released. D When the brake fluid level is low...
ignition key
turned
the
is
CAUTION
It is dangerous to continue driving normally when the brake fluid level is low.
Have your vehicle checked at your Toyota dealer in the following cases: D The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.
D The light does not come on even if the ignition key is turned on with the park- ing brake released.
A warning light turning on briefly during operation does not indicate a problem.
122
’04 AVALON U (L/O 0408)
CAUTION
(b) Driver’s Seat Belt Reminder Light
and Buzzer
If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The
light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. De- press the brake pedal firmly and bring the vehicle to an immediate stop.
D The brake system warning light re- mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely un- stable during braking.
to
remind you
light and buzzer
This buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light keep flashing and the buzz- er sounds for about 4 to 8 seconds. (c) Front Outside Passenger’s Seat Belt
Reminder Light
This light reminds you to buckle up the front outside passenger’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front outside passen- ger seat and does not fasten the seat belt. Unless the front outside passenger fastens the belt, the light stays on. This light reminds you to buckle up the front outside passenger’s seat belt. If luggage or other load is placed on the front outside passenger seat, depending on its weight and how it is placed on the seat, built−in sensors in the seat cushion may detect the pressure, causing the re- minder light to come on.
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
(d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.
NOTICE
Do not continue driving if the engine drive belt is broken or loose.
(e) Low Engine Oil Pressure Warning
Light
This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance.
light may occasionally
The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.
low. It
NOTICE
Do not drive the warning light on—even for one block. It may ruin the engine.
the vehicle with
(f) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on, or the lamp comes on while driving, first check the followings. D Empty fuel tank
If the fuel tank is empty, refuel immedi- ately.
D Loose fuel tank cap
If the fuel tank cap is loose, securely tighten it.
These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp does not go off even after several trips, contact your Toyota dealer as soon as possible. If the fuel tank is not empty or the fuel tank cap is not loose... D There is a problem somewhere in the engine, emission control system, auto- matic transmission electrical system or warning light system itself.
inspection
Contact your Toyota dealer as soon as possible to service the vehicle. Emissions Inspection and Maintenance (I/M) programs Your vehicle may not pass a state emission the malfunction indicator lamp remains on. Contact your to check your vehicle’s Toyota dealer emission and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection. For details, see “Emissions Inspection and Maintenance (I/M) programs” in Section 6.
system
control
if
123
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
If either of the following conditions oc- curs, this indicates a malfunction some- where in the components monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.
D The light comes on while you are driv-
ing.
A warning light turning on briefly during operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.
(i) Open Door Warning Light This light remains on until all the doors are completely closed. (j) Rear Light Failure Warning Light If this light comes on when the headlight switch is turned on, it indicates that one or more of the tail lights are burned out. If it comes on when the brake pedal is depressed, one or more stop lights are burned out. Have defective bulbs replaced as soon as possible. (k) SRS Warning Light This light will come on when the igni- tion key is turned to the “ON” position. After about 6 seconds, the light will go off. This means the system of the air- bags and front seat belt pretensioners are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side airbag sensors, driver’s seat position sensor, driver’s seat belt buckle switch, front seat belt pretensioner assem- blies, inflators, warning light, interconnect- ing wiring and power sources.
light system monitors
few seconds. Thereafter,
(g) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual. (h) “ABS” Warning Light The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system and the brake assist system work properly, the light turns off after a the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system, the brake assist system, the traction control system and the vehicle stability control system do not operate, but the brake system still oper- ates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.
if
124
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle.
D The light does not come on when the
ignition key is turned to the “ON” posi-
tion or remains on for more than 6
seconds or flashes.
D The light comes on or starts flashing
while driving.
(l) “VSC” Warning Light The light warns that there is a problem somewhere in the vehicle stability control system or traction control system. The light will come on when the ignition key is turned to “ON”, and will go off after about a few seconds. If the light comes on while driving, the vehicle stability control system and trac- tion control system do not work. However, as conventional braking operates when ap- plied, there is no problem to continue your driving.
In the following cases, contact your Toyota dealer: D The light does not come on after the
ignition is turned to on.
D The light is left on after the ignition is
turned to on.
D The light comes on while driving. The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed. (m) Low Windshield Washer Fluid Level
Warning Light
The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” in Section 7−3.) (n) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position.
light
SERVICE
CHECKING REMINDER INDICATORS (except the low fuel level warning low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the doors.
and
The open door warning come on.
light should
3. Close the door.
The open door warning light should go off.
4. Turn the ignition key to “ON”, but do
not start the engine. All the service reminder indicators ex- cept the open door warning light should come on. The “ABS” and “VSC” warn- ing lights, “TRAC OFF” and slip indica- tor lights go off after a few seconds. The SRS warning light goes off after about 6 seconds.
If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.
125
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
SECTION 1− 7
OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traction control system Vehicle stability control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
127
128
135
138
139
140
126
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Ignition switch with steering lock
immobilizer system”
You must push in the key to turn the key from “ACC” to the “LOCK” position. The selector lever must be in the “P” position before pushing the key. Vehicles with engine immobilizer system— Once you remove the key, the engine im- mobilizer system is automatically set. (See “Engine in Section 1−2.) When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently. If the automatic unlocking operation linked with the ignition switch is set, all doors are automatically unlocked when the igni- tion switch is turned from the “ON” posi- tion to the “ACC” or “LOCK” position. For details, see “—Automatic door locking and unlocking functions” in Section 1−2.
NOTICE
leave the key
Do not in the “ON” position if the engine is not running. The battery will discharge and the ignition could be damaged.
127
2004 AVALON from Aug. ’04 Prod. (OM41412U)
“START”—Starter motor on. The key will return to the “ON” position when released. For starting tips, see Section 3. “ON”—Engine on and all accessories on. This is the normal driving position. “ACC”—Accessories such as the radio operate, but the engine is off. the “ACC” or If you “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key. “LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position.
the key
leave
in
’04 AVALON U (L/O 0408)
Automatic transmission "Floor shift type
Lock release button To prevent misshifting
Selector lever
Overdrive switch
With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in “ON” position.)
Shift while holding the lock release button in.
Shift normally.
128
Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” position and the lock re- lease button depressed). (a) Selector lever The shift position is also displayed on the instrument cluster. P: Parking, engine starting and
key removal
R: Reverse N: Neutral D: Normal driving (with overdrive on) 2: Stronger engine braking L: Maximum engine braking
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
releasing
the cruise control
When the cruise control is being used, even if you downshift the transmission by pushing and the overdrive switch, engine braking will not be enabled because is not can- celled. For ways to decrease the vehicle speed, see “Cruise control” in this Section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” in Section 3. The transmission must be in “P” or “N”.
2. With your foot holding down the brake
pedal, shift the selector lever to “D”.
When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into the over- drive gear even with the overdrive on.
temperature
low,
is
CAUTION
Never put your foot on the accelera- tor pedal while shifting.
3. Release the parking brake and brake the accelerator pedal
pedal. Depress slowly for smooth starting.
If the automatic locking operation linked with the shift position is set, all doors are automatically locked when the selector le- ver is moved out of the “P” position after the ignition switch is turned to the “ON” position and all the doors are closed. For details, see “—Automatic door locking and unlocking functions” in Section 1−2. (d) Using engine braking To use engine braking, you can downshift the transmission as follows: D Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to third gear.
D Shift into the “2” position. The trans- mission will downshift to second gear when the vehicle speed drops down to or lower than 132 km/h (82 mph), and stronger engine braking will be en- abled.
D Shift into the “L” position. The trans- first gear mission will downshift when the vehicle speed drops down to or lower than 59 km/h (36 mph), and maximum engine braking will be en- abled.
to
129
2004 AVALON from Aug. ’04 Prod. (OM41412U)
(b) Overdrive switch You can select either third gear (with overdrive off) or fourth gear (with over- drive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will automatically be on.
for better
releasing
When the cruise control is being used, even if you downshift the transmission by pushing and the overdrive switch, engine braking will not be enabled because is not can- celled. For ways to decrease the vehicle speed, see “Cruise control” in this Section.
the cruise control
CAUTION
Be careful when downshifting on a slippery shifting could cause the vehicle to skid or spin.
surface. Abrupt
(e) Using “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in first gear and automatically shift to second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.
130
’04 AVALON U (L/O 0408)
NOTICE
z Be careful not to over−rev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference:
“2” “L”
. . . . . . . . . . . . . . . . . . . . . . .
139 km/h (86 mph) 76 km/h (47 mph) z Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmission dam- age from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.
(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.
NOTICE
Never shift into reverse while the ve- hicle is moving.
(g) Parking 1. Bring the vehicle to a complete stop. 2. With
the brake pedal pressed down, fully depress the parking brake pedal to apply the parking brake securely.
3. With
the brake pedal pressed down, shift the selector lever to the “P” posi- tion.
CAUTION
Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.
If the automatic unlocking operation linked with the shift position is set, all doors are automatically unlocked when the selector lever is moved to the “P” position after the ignition switch is turned to the “ON” position. For details, see “—Automatic door locking and unlocking functions” in Section 1−2.
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
(i)
If you cannot shift the selector le- ver out of “P” position
is depressed, use
If you cannot shift the selector lever from the “P” position even though the brake pedal lock override button. For instructions, see “If you cannot shift automatic transmission selector lever” in Section 4.
the shift
(h) Good driving practice D If the transmission repeatedly shifts up and down between third gear and over- drive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately after- ward.
D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.
CAUTION
Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.
NOTICE
Always use the brake pedal or the parking brake to hold the vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator ped- al, as this can cause the transmission to overheat.
131
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
"Column shift type
Selector lever
Overdrive switch
With the brake pedal depressed, shift while pilling the selector lever toward you. (The ignition switch must be in “ON” position.)
Shift while pulling the selector lever toward you.
Shift normally.
132
Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” position and the selector lever pulled toward you). (a) Selector lever The shift position is displayed on the in- strument cluster. P: Parking, engine starting and
key removal
R: Reverse N: Neutral D: Normal driving (with overdrive on) 2: Stronger engine braking L: Maximum engine braking
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
releasing
the cruise control
When the cruise control is being used, even if you downshift the transmission by pushing and the overdrive switch, engine braking will not be enabled because is not can- celled. For ways to decrease the vehicle speed, see “Cruise control” in this Section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” in Section 3. The transmission must be in “P” or “N”.
2. With your foot holding down the brake
pedal, shift the selector lever to “D”.
When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into the over- drive gear even with the overdrive on.
temperature
low,
is
CAUTION
Never put your foot on the accelera- tor pedal while shifting.
3. Release the parking brake and brake the accelerator pedal
pedal. Depress slowly for smooth starting.
If the automatic locking operation linked with the shift position is set, all doors are automatically locked when the selector le- ver is moved out of the “P” position after the ignition switch is turned to the “ON” position and all the doors are closed. For details, see “—Automatic door locking and unlocking functions” in Section 1−2. (d) Using engine braking To use engine braking, you can downshift the transmission as follows: D Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to third gear.
D Shift into the “2” position. The trans- mission will downshift to second gear when the vehicle speed drops down to or lower than 132 km/h (82 mph), and stronger engine braking will be en- abled.
D Shift into the “L” position. The trans- first gear mission will downshift When the vehicle speed drops down to or lower than 59 km/h (36 mph), and maximum engine braking will be en- abled.
to
133
2004 AVALON from Aug. ’04 Prod. (OM41412U)
(b) Overdrive switch You can select either third gear (with overdrive off) or fourth gear (with over- drive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will automatically be on.
for better
releasing
When the cruise control is being used, even if you downshift the transmission by pushing and the overdrive switch, engine braking will not be enabled because is not can- celled. For ways to decrease the vehicle speed, see “Cruise control” in this Section.
the cruise control
CAUTION
Be careful when downshifting on a slippery shifting could cause the vehicle to skid or spin.
surface. Abrupt
(e) Using “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in first gear and automatically shift to second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.
134
’04 AVALON U (L/O 0408)
NOTICE
z Be careful not to overrev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference:
“2” “L”
. . . . . . . . . . . . . . . . . . . . . . .
139 km/h (86 mph) 76 km/h (47 mph) z Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmission dam- age from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.
(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.
NOTICE
Never shift into reverse while the ve- hicle is moving.
(g) Parking 1. Bring the vehicle to a complete stop. 2. With
the brake pedal pressed down, fully depress the parking brake pedal to apply the parking brake securely.
3. With
the brake pedal pressed down, shift the selector lever to the “P” posi- tion.
CAUTION
Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.
If the automatic unlocking operation linked with the shift position is set, all doors are automatically unlocked when the selector lever is moved to the “P” position after the ignition switch is turned to the “ON” position. For details, see “—Automatic door locking and unlocking functions” in Section 1−2.
2004 AVALON from Aug. ’04 Prod. (OM41412U)
(h) Good driving practice D If the transmission repeatedly shifts up and down between third gear and over- drive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately after- ward.
D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.
CAUTION
Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.
NOTICE
Always use the brake pedal or the parking brake to hold the vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator ped- al, as this can cause the transmission to overheat.
’04 AVALON U (L/O 0408)
(i)
If you cannot shift the selector le- ver out of “P” position
is depressed, use
If you cannot shift the selector lever from the “P” position even though the brake pedal lock override button. For instructions, see “If you cannot shift automatic transmission selector lever” in Section 4.
the shift
Traction control system The traction control system automatical- ly helps prevent the spinning of front wheels when the vehicle is started or accelerated on slippery road surfaces. When the ignition key is turned to “ON”, the system automatically turns on.
CAUTION
Under certain slippery road condi- tions, full traction of the vehicle and power against front wheels cannot be maintained, even though the traction control system is in operation. Do not drive the vehicle under any speed or maneuvering conditions which may cause traction control. In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tire chains. Always drive at an appropriate and cautious speed the present road condi- tions.
the vehicle
tires or
lose
for
to
135
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
When the traction control system is oper- ating, the following conditions occur: D The system controls the spinning of the front wheels. At this time, the slip indi- cator light blinks.
D You may feel vibration or noise in your the is
vehicle, caused by operation of brakes. This functioning properly.
the system
indicates
The slip indicator light comes on for a few seconds when the ignition key is turned to “ON”. If the indicator light does not come on when the ignition is turned on, contact your Toyota dealer.
TRACTION CONTROL OFF MODE When getting the vehicle out of mud or newly fallen snow, etc., turn off the traction control system. This system that controls engine performance inter- feres with the process of freeing front wheels. To turn off: Push “TRAC OFF” switch. The “TRAC OFF” indicator light will come on. The vehicle stability control system is al- ways activated, even if the traction control system is turned off. To turn on: Push “TRAC OFF” switch once again. The “TRAC OFF” indicator light will go off.
2004 AVALON from Aug. ’04 Prod. (OM41412U)
that
NORMAL DRIVING MODE Leave the system on during the ordi- nary driving so it can operate when needed. You may hear a sound the engine compartment for a few seconds when the engine is started or just after the vehicle begins to move. This means that the trac- tion control system is in the self−check mode, but does not indicate a malfunction.
in
136
to “ON”.
“TRAC OFF” indicator light comes on for a few seconds when the ignition key is turned It will come on again when you push the “TRAC OFF” switch to turn off the system. In the following cases, contact your Toyota dealer: D The indicator light does not come on when the ignition key is turned “ON”. D The indicator light remains on after the
ignition is turned on.
D The indicator light comes on with the
normal driving mode while driving.
’04 AVALON U (L/O 0408)
“VSC” warning light This light warns that there is a problem somewhere in the traction control system or the vehicle stability control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.
In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the
ignition key is turned to “ON”.
D The warning light comes on while driv-
ing.
The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.
137
2004 AVALON from Aug. ’04 Prod. (OM41412U)
Vehicle stability control
system
The vehicle stability control system
helps provide integrated control of the
systems such as anti−lock brake sys-
tem,
traction control, engine control,
etc. This system automatically controls
the brakes and engine to help prevent
the vehicle from skidding when corner-
ing on a slippery road surface or oper-
ating steering wheel abruptly.
This system will activate when your ve-
hicle speed reaches or exceeds 15 km/h
(9 mph), and will deactivate when the ve-
hicle speed reduces to below 15 km/h (9
mph).
You may hear a sound
the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the sys-
tem is in the self−check mode but does
not indicate a malfunction.
in
138
’04 AVALON U (L/O 0408)
CAUTION
D Do not rely excessively on the ve- hicle stability control system. Even if the vehicle stability control sys- tem is operating, you must always drive carefully and attentively to avoid serious injury. Reckless driv- ing will result in an unexpected ac- cident. light flashes and an alarm sounds, spe- cial care should be taken while driving.
indicator
the slip
If
D Only use tires of specified size. The size, manufacture, brand and tread pattern for all 4 tires should be the same. If you use the tires other than specified, different type or size, the vehicle stability control system may not function correctly. When replacing the tires or wheels, contact your Toyota dealer. (See “Checking and replacing tires” in Section 7−2.)
D In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tires or tire chains.
If the vehicle is going to skid during driv- ing, the slip indicator light blinks and an alarm sounds intermittently. Special care should be taken while driving. The slip indicator light comes on for a few seconds when the ignition key is turned to “ON”. If the indicator light does not come on when the ignition is turned on, contact your Toyota dealer.
2004 AVALON from Aug. ’04 Prod. (OM41412U)
’04 AVALON U (L/O 0408)
Parking brake
In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the
ignition key is turned to “ON”.
D The warning light comes on while driv-
ing.
The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.
Type A
Type B
139
2004 AVALON from Aug. ’04 Prod. (OM41412U)
“VSC” warning light This light warns that there is a problem somewhere in the vehicle stability control system or the traction control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.
’04 AVALON U (L/O 0408)
When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Fully depress the parking brake pedal. For better holding power, first de- press the brake pedal and hold it while setting the parking brake. To release: Depress pedal while depressing the brake pedal. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.
the parking brake
CAUTION
Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.
Cruise control
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) with your foot off the
accelerator pedal.
Your cruising speed can be maintained
although a slight speed change may occur
when driving up or down gradient, within
the
limits of engine performance. On
steeper hills, a greater speed change will
occur so it is better to drive without the
cruise control.
When the cruise control is on, the driving
pattern of the automatic transmission is
fixed in the normal position, regardless of
the position of the selector switch.
CAUTION