2011 Toyota 4runner Owners Manual

429

3-7. Other interior features Vanity mirrors

Slide the cover to open.

The light turns on when the cover is opened.

CTH37AS008

NOTICE

■To prevent battery discharge

Do not leave the vanity lights on for extended periods while the engine is off.

430

3-7. Other interior features Clock

Adjusts the hours Adjusts the minutes

431

3-7. Other interior features

■For quicker adjustment of the clock

To advance the minutes and hours quickly, press and hold the “M” or “H” but- ton. The time can be adjusted back or forth by following the procedure below:

” or “SET/

The hour or minute can be moved for- ward or backward by pressing the “MODE/ ” button while pressing and holding the “H” or “M” but- ton. If the “MODE/ ” but- ton is also pressed and held in the above operation, the hour or minute will move faster.

” or “SET/

■The clock is displayed when

Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.

■When disconnecting and reconnecting battery terminals

The clock data will be reset.

432

3-7. Other interior features Outside temperature display

The temperature display shows temperatures within the ranges of -40°F (-40°C) and 122°F (50°C). Vehicles without Multi-terrain Select

433

3-7. Other interior features

Vehicles with Multi-terrain Select

■The outside temperature is displayed when

Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

434

3-7. Other interior features

■ICE indicator

Vehicles without Multi-terrain Select

If the outside temperature lowers to 37 °F (3 °C) or below when the engine switch is in the “ON” position (vehicles without a smart key system) or the “ENGINE START STOP” switch is in IGNITION ON mode (vehicles with a smart key system), the “ICE” indicator will come on to warn the driver that roads may be icy. Check the road surface and drive carefully. (The indicator will go off when the outside tem- perature rises to 41 °F [5 °C].)

Vehicles with Multi-terrain Select

If the outside temperature lowers to 37 °F (3 °C) or below when the engine switch is in the “ON” position, the “ICE” indicator will come on to warn the driver that roads may be icy. Check the road surface and drive carefully. (The indicator will go off when the outside temperature rises to 41 °F [5 °C].)

■Display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change: ●When the vehicle is stopped, or moving at low speeds (less than 14 mph

[24 km/h])

●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

435

3-7. Other interior features Power outlets (12V DC)

The power outlet can be used for 12 V accessories that run on less than 10 A. Center panel

CTH37AS006

436

3-7. Other interior features

Glove box

Luggage compartment (vehicles without the 120V AC)

CTH37AS019

CTH37AS085

437

3-7. Other interior features

Luggage compartment (vehicles with the 120V AC)

CTH37AS086

■The power outlet can be used when

Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.

NOTICE

■To avoid damaging the power outlet

Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.

■To prevent blown fuse

Do not use an accessory that uses more than 12 V 10 A.

■To prevent battery discharge

Do not use the power outlet longer than necessary when the engine is not running.

438

3-7. Other interior features Power outlets (120V AC)∗

The power outlet can be used for electrical appliances. Main switch

To use the power outlet, turn on the main switch.

The power supply starts a few seconds after the main switch is pressed.

Power outlet socket (in the console box)

CTH37AS055

CTH37AS023

∗: If equipped 439

3-7. Other interior features

Power outlet socket (luggage compartment)

CTH37AS087

Maximum available capacity of the power outlet

■ While the vehicle is being driven

The maximum capacity of the power outlet is always 120V AC/ 100W.

■ When the vehicle is stationary

The maximum capacity of the power outlet varies depending on the position of the shift lever. ● The maximum capacity is 120V AC/100W when the shift lever is

in any position other than P or N.

● The maximum capacity is 120V AC/400W when the shift lever is

in P or N. The maximum capacity of 400W can only be restored by turning the power outlet main switch off and then on again with the shift lever in P or N.

440

3-7. Other interior features

■The power outlet can be used when

The engine is running.

■The indicator light changes according to the maximum available

capacity as follows:

120V AC/400W 120V AC/100W

CTH37AS025

■When the power outlet is in operation

The sound of the cooling fan may be heard from the right side of the luggage compartment. This is normal and does not indicate a malfunction. ■If the engine is started with the power outlet main switch on

The maximum capacity of the power supply may decrease to below the stan- dard, or may be cut off completely, even when the vehicle is stationary.

■The protection circuit may be activated to cut the power supply if any

of the following conditions apply: ●The engine is started with the power outlet main switch on. ●Use of electrical appliances exceeding the maximum capacity is

attempted. A sound may be heard when the protection circuit is activated. This is nor- mal and does not indicate a malfunction.

●Electrical appliances, which consume power exceeding 100W, have

been used continuously for a long time period.

●The total power usage by all electrical features (headlights, air condition- ing, etc.) has exceeded the total vehicle maximum for an extended period of time.

441

3-7. Other interior features

■If the protection circuit is activated and the power supply is cut, con-

duct the following procedure:

STEP 1

STEP 2

STEP 3

STEP 4

Park the vehicle in a safe place, and then securely apply the park- ing brake. Check and ensure that the shift lever is in P or N. Make sure that the power consumption of the electric appliance is within the maximum capacity of the power outlet and the appliance is not broken. Press the power outlet main switch again.

When the cabin temperature is high, open the windows to cool the tempera- ture down. Once it reaches the normal temperature, turn the power outlet main switch on again. If the power supply does not resume even after the above procedure has been performed, have the vehicle inspected by your Toyota dealer.

442

3-7. Other interior features

CAUTION

■Using a power outlet

Observe the following precautions to reduce the risk of injury. ●Use of the power outlet when it is wet with water or snow may result in electrical shocks and is extremely dangerous. The power outlet must be thoroughly dried before use.

●Do not allow children to use or play with the power outlet. ●Be careful not to get any part of your body caught in the power outlet lid. ●When using electrical appliances, strictly follow any cautions and notices

written on their labels and in the manufacturers' instruction manuals.

●Do not modify, disassemble or repair the power outlet or its inverter in any way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact your Toyota dealer for any necessary repairs.

■To prevent injuries and accidents, secure all electric appliances before

use and do not use any appliances that may do any of the following: ●Distract the driver while driving, or hamper safe driving. ●Result in a fire or burn injuries due to the appliance rolling, falling or over-

heating while driving.

●Emit steam while the windows of the cabin are closed.

■To prevent unexpected accidents, such as electric shocks, do not per-

form any of the following actions: ●Using the power outlet for electric heaters while sleeping. ●Contaminating the power outlet with liquid substances or mud. ●Handling electrical appliance plugs at the power outlet with wet hands or

feet.

●Inserting foreign objects into the power outlet. ●Using malfunctioning electric appliances. ●Inserting inappropriate or badly fitting plugs into the power outlet.

443

3-7. Other interior features

NOTICE

■To avoid damaging the power outlet and the plug

●Close the power outlet lid when not in use. ●Do not allow foreign objects or liquids to enter the power outlet, as this

may cause a short circuit.

●Do not use plug adaptors to connect too many plugs to the power outlet. ●After removing a plug, gently close the power outlet lid.

■To prevent the fuse from being blown

Do not use a 120V AC appliance that requires more than the maximum capacity of the power outlet. If a 120V AC appliance that consumes more than the maximum capacity is used, the protection circuit will cut the power supply.

■Appliances that may not operate properly (120V AC)

The following 120V AC appliances may not operate even if their power con- sumption is under maximum capacity. ●Appliances with high initial peak wattage ●Measuring devices that process precise data. ●Other appliances that require an extremely stable power supply

■To prevent battery discharge

Turn off all the vehicle's electronic equipment and accessories, such as the headlights and air conditioning, when electrical appliances that consume in excess of 100W are used continuously for long periods of time.

■To prevent any damage caused by heat

●Do not use any electrical appliances that give off intense heat, such as toasters, in any locations including the internal or external trim, seats and deck.

●Do not use any electrical appliances that are easily affected by vibration or heat inside the vehicle. Vibration while driving, or the heat of the sun while parking, may result in damage to those electrical appliances.

444

3-7. Other interior features

NOTICE

■If any electrical appliances are to be used while driving

Securely fasten both the appliances and their cables to prevent them from falling or getting caught in any of the power train components.

■If the power outlet is loose when an electrical appliance plug is con-

nected Replace the outlet. Contact your Toyota dealer for any necessary replace- ments.

■If the power outlet gets dirty

Turn the main switch off and use a soft, clean cloth to wipe it gently. Do not use any cleansing materials, such as organic solvents, wax, or compound cleaners, as these may damage the power outlet or cause it to malfunction.

445

3-7. Other interior features Seat heaters∗

Front passenger’s seat

Driver’s seat

CTH37AS005

On The indicator light comes on. Adjusts the seat tempera- ture The further you move the dial forward, the warmer the seat becomes.

■The seat heaters can be used when

Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

■When not in use

Move the dial fully backward. The indicator light turns off.

446

∗: If equipped

3-7. Other interior features

CAUTION

■Burns

●Use caution when seating the following persons in a seat with the seat

heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically chal-

lenged

• Persons with sensitive skin • Persons who are fatigued • Persons who have taken alcohol or drugs that induce sleep (sleeping

drugs, cold remedies, etc.)

●Do not cover the seat with anything when using the seat heater.

Using the seat heater with a blanket or cushion increases the temperature of the seat and may lead to overheating.

●Do not use the seat heater more than necessary. Doing so may cause

minor burns or overheating.

NOTICE

■To prevent seat heater damage

Do not put heavy objects that have an uneven surface on the seat and do not stick sharp objects (needles, nails, etc.) into the seat.

■To prevent battery discharge

Turn the seat heaters off when the engine is not running.

447

3-7. Other interior features Armrest

Fold down the armrest for use.

CTH37AS088

NOTICE

■To prevent damage to the armrest

Do not apply too much load on the armrest.

448

3-7. Other interior features Floor mat

Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.

Fix the floor mat in place using the retaining hooks (clips) pro- vided.

For details, refer to the floor mat retention clip installation instructions supplied with the clips.

CAUTION

Observe the following precautions. Failure to do so may cause the driver's floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. ■When installing the driver's floor mat

●Do not use floor mats designed for other models or different model year

vehicles, even if they are Toyota Genuine floor mats.

●Only use floor mats designed for the driver's seat. ●Always install the floor mat securely using the retaining hooks (clips) pro-

vided.

●Do not use two or more floor mats on top of each other. ●Do not place the floor mat bottom-side up or upside-down.

■Before driving

●Check that the floor mat is securely fixed in the right place with all the pro- vided retaining hooks (clips). Be espe- cially careful to perform this check after cleaning the floor.

●With the engine stopped and the shift lever in P, fully depress each pedal to the floor to make sure it does not inter- fere with the floor mat.

449

3-7. Other interior features Compass

The compass on the accessory meter display indicates the direction in which the vehicle is heading.

” button

“MODE/ “SET/ ” button Direction display

■ Displays and directions

Display

“N” “NE” “E” “SE” “S” “SW” “W” “NW”

450

Direction

North

Northeast

East

Southeast

South

Southwest

West

Northwest

3-7. Other interior features

Calibrating the compass

Samoa: 5 Guam: 8 Saipan: 8

CTH37AS072

The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies depending on the geographic position of the vehicle.

If you cross over one of the map boundaries shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to “Deviation calibra- tion”.

451

3-7. Other interior features

Deviation calibration

STEP 1

STEP 2

Stop the vehicle. Change the accessory meter display to deviation calibration mode by doing the following.

Vehicles without Multi-terrain Select

”

lights are

the parking

When turned on: Press and hold the “MODE/ button. A number (1 to 15) will appear on the display. When the parking lights are off: In accessory meter light control mode (→P. 196), press and hold the “MODE/ A number (1 to 15) will appear on the display.

” button.

Vehicles with Multi-terrain Select

452

”

lights are

the parking

When turned on: Press and hold the “MODE/ button. A number (1 to 15) will appear on the display. When the parking lights are off: In accessory meter light control mode (→P. 196), press and hold the “MODE/ A number (1 to 15) will appear on the display.

” button.

3-7. Other interior features

STEP 3

Referring to the map above, press the “MODE/

” or “SET/

” button to select the number of the zone you are in.

STEP 4

Press and hold the “SET/ ” button to confirm the number and to exit deviation calibration mode. (If the button is pressed for more than 6 seconds, the number will automatically be confirmed and the display returned to normal.)

Circling calibration

If “•” appears on the left side of the direction display, circling cali- bration needs to be performed.

STEP 1

STEP 2

Stop the vehicle in a place where it is safe to drive in a circle. In deviation calibration mode (→P. 452), press and hold the “MODE/ ” button to change to circling calibration mode.

“•” on the left side of the direction display will blink.

453

3-7. Other interior features

STEP 3

Drive the vehicle at 5 mph (8 km/ h) or less in a circle until a direc- tion is displayed.

If there is not enough space to drive in a circle, drive around the block until a direction is dis- played.

STEP 4

STEP 5

” button to confirm the direction Press and hold the “SET/ and to exit circling calibration mode. (If the button is pressed for several minutes, the direction will automatically be con- firmed and the display returned to normal.) Make sure that “•” on the left side of the direction display has gone off. If “•” is illuminated, perform the above procedure again.

■Conditions unfavorable to correct operation

The compass may not show the correct direction in the following conditions: ●The vehicle is stopped immediately after turning. ●The vehicle is on an inclined surface. ●The vehicle is in a place where the earth's magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).

●The vehicle has become magnetized.

(There is a magnet or metal object near the accessory meter display.)

●The battery has been disconnected. ●A door is open.

454

3-7. Other interior features

■Circling calibration error message (vehicles with Multi-terrain Select)

In the following situations, an error mes- sage regarding the circling calibration will appear on the accessory meter display for a few seconds: ●The vehicle was driven too fast during

the circling calibration.

●The circling calibration was not com- pleted successfully within about two minutes.

CAUTION

■While driving the vehicle

Do not adjust the display. Adjust the display only when the vehicle is stopped.

■When doing the circling calibration

Secure a wide space, and watch out for people and vehicles in the vicinity. Do not violate any local traffic rules while performing circling calibration.

NOTICE

■To avoid compass malfunctions

Do not place magnets or any metal objects near the accessory meter dis- play. Doing this may cause the compass sensor to malfunction.

■To ensure normal operation of the compass

●Do not perform a circling calibration of the compass in a place where the earth's magnetic field is subject to interference by artificial magnetic fields. ●During calibration, do not operate electric systems (moon roof, power win-

dows, etc.) as they may interfere with the calibration.

455

3-7. Other interior features Luggage compartment features

■ Cargo hooks Vehicles with third seats

STEP 1

Fold down the third seats. (→P. 72)

STEP 2

Raise the hook to use.

The cargo hooks are provided for securing loose items.

Vehicles without third seats

CTH37AS041

Raise the hook to use.

The cargo hooks are provided for securing loose items.

CTH37AS089

456

3-7. Other interior features

■ Cargo net hooks

The cargo net itself is not included as original equipment.

Vehicles with third seats (pattern 1)

Raise the rear cargo hook to use.

CTH37AS075

Vehicles with third seats (pattern 2)

STEP 1

Fold down the third seats. (→P. 72)

STEP 2

Raise the cargo hook to use.

Vehicles without third seats (pattern 1)

CTH37AS076

Raise the rear cargo hook to use.

CTH37AS090

457

3-7. Other interior features

Vehicles without third seats (pattern 2)

Raise the cargo hook to use.

CTH37AS091

■ Storage compartment Type A (if equipped)

Open the storage compart- ment as shown.

Type B (if equipped)

CTH37AS014

Open the storage compart- ment as shown.

CTH37AS092

458

■ Slide deck (if equipped)

CTH37AS093

■ Grocery bag hooks Type A

CTH37AS094

3-7. Other interior features

Slide the deck while turning the lock release lever, and then release the lever after sliding the deck to the lock position.

Half-slide locked position Full-slide locked position

459

3-7. Other interior features

Type B (if equipped)

To use the grocery bag hooks, slide the slide deck to the full- slide locked position. (→P. 459)

CTH37AS095

CAUTION

■When the cargo hooks are not in use

To avoid injury, always return the cargo hooks to their stowed positions.

■Slide deck operating precaution (if equipped)

●Be careful not to get hands or feet pinched by the slide deck. ●Be careful not to allow the slide deck to hit any persons or luggage while

sliding the deck.

●Do not operate the slide deck while someone is on it.

Doing so may cause an accident.

●If operating the slide deck when the vehicle is stopped on an incline, the slide deck may move faster. Be careful not to allow the slide deck to hit you or pinch your fingers etc.

●After sliding the deck, make sure it is securely locked in position. ●Do not close the back door while any person is sitting on the slide deck or

any person is between the slide deck and back door.

●Do not stow any objects into the space between the slide deck rails.

460

3-7. Other interior features

NOTICE

■To prevent damage to the cargo net hooks

Avoid hanging things other than a cargo net on them.

■Slide deck weight capacity (if equipped)

Do not load anything heavier than 440 lb. (200 kg) on the sliding deck.

■Grocery bag hook weight capacity

Do not hang any object heavier than 8.8 lb. (4 kg) on the grocery bag hooks.

■When using the slide deck (if equipped)

●Do not close the back door while the slide deck is sliding out. Doing so

may cause the back door or slide deck to break.

●If operating the slide deck when the vehicle is stopped on an incline, the slide deck may move faster. Be careful as luggage may become damaged or fly out and damage the cabin.

461

3-7. Other interior features Garage door opener

The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices.

The garage door opener (HomeLink® Universal Transceiver) is manufac- tured under license from HomeLink®.

Programming HomeLink® (for U.S. owners)

The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.

Indicator light Buttons

CTH37AS044

462

■ Programming HomeLink®

STEP 1

STEP 2

3-7. Other interior features

Point the remote control trans- mitter for the device 1 to 3 in. (25
to 75 mm) from the HomeLink® buttons.

Keep the HomeLink® indicator light in view while programming.

the Press and hold one of HomeLink® buttons and the the transmitter button. When HomeLink® light changes from a slow to a rapid flash after 20 seconds, release both buttons.

indicator

463

3-7. Other interior features

STEP 3

Test the HomeLink® operation by pressing the newly pro- grammed button.

If a HomeLink® button has been programmed for a garage door, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the rolling code type. Press and hold the programmed HomeLink® button. The remote control transmitter is of the rolling code type if the HomeLink® indicator light flashes rapidly for 2 seconds and then remains lit. If your transmitter is the rolling code type, proceed to the heading “Programming a roll- ing code system”.

STEP 4

Repeat the steps above to program another device for any of the remaining HomeLink® buttons.

464

3-7. Other interior features

■ Programming a rolling code system (for U.S. owners)

If your device is rolling code equipped, follow the steps under the heading “Programming HomeLink®” before proceeding with the steps listed below.

STEP 1

STEP 2

STEP 3

STEP 4

Locate the learn button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener. Refer to the operation manual supplied with the garage door opener for the location of the learn button. Press the learn button. Following this step, you have 30 seconds in which to initiate step 3
below. Press and release the vehicle’s programmed HomeLink® but- ton twice. The garage door may open. If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door. The ceiling mounted garage door opener motor should now recog- nize the HomeLink® signal and operate the garage door. Repeat the steps above to program another rolling code sys- tem for any of the remaining HomeLink® buttons.

465

3-7. Other interior features

■ Programming an entry gate (for U.S. owners)/Programming a

device in the Canadian market

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

STEP 6

Place the remote control transmitter 1 to 3 in. (25 to 75 mm) away from the HomeLink® buttons. Keep the HomeLink® indicator light in view while programming. Press and hold the selected HomeLink® button. Repeatedly press and release (cycle) the remote control transmitter for 2 seconds each until step 4 is completed. When the HomeLink® indicator light starts to flash rapidly, release the buttons. Test the HomeLink® operation by pressing the newly pro- grammed button. Check to see if the gate/device operates correctly. Repeat the steps above to program another device for any of the remaining HomeLink® buttons.

■ Programming other devices

To program other devices such as home security systems, home door locks and lighting, contact your Toyota dealer for assistance.

■ Reprogramming a button

The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the “Reprogramming a HomeLink® button” instructions.

466

3-7. Other interior features

Operating HomeLink®

Press the appropriate HomeLink® button. The HomeLink® indicator light should come on.

The HomeLink® compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed.

Erasing the entire HomeLink® memory (all three programs)

Press and hold the 2 outside but- tons for 20 seconds until the indi- cator light flashes.

If you sell your vehicle, be sure to erase the programs stored in the HomeLink® memory.

■Before programming

●Install a new battery in the remote control transmitter. ●The battery side of the remote control transmitter must be pointed away

from the HomeLink® button.

467

3-7. Other interior features

■Certification for the garage door opener

For vehicles sold in the U.S.A. FCC ID: CB2300NHL3
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For vehicles sold in Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

■When support is necessary

Visit on the web at www.homelink.com or call 1-800-355-3515.

CAUTION

■When programming a garage door or other remote control devices

The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm.

■Conforming to federal safety standards

Do not use the HomeLink® compatible transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards. This includes any garage door that cannot detect an interfering object. A door or device without these features increases the risk of death or serious injury.

468

3-7. Other interior features Safety Connect∗

Safety Connect is a subscription-based telematics service that uses Global Positioning System (GPS) data and embedded cellular tech- nology to provide safety and security features to subscribers. Safety Connect is supported by Toyota’s designated response center, which operates 24 hours per day, 7 days per week. Safety Connect service is available by subscription on select, telematics hardware-equipped vehicles. By using the Safety Connect service, you are agreeing to be bound by the Telematics Subscription Service Agreement and its Terms and Conditions, as in effect and amended from time to time, a current copy of which is available at Toyota.com. All use of the Safety Con- nect service is subject to such then-applicable Terms and Condi- tions. ■ System components

Microphone “SOS” button LED light indicators

CTH37AS054

∗: If equipped 469

3-7. Other interior features

■ Services

Subscribers have the following Safety Connect services avail- able: ● Automatic Collision Notification*

Helps drivers receive necessary response from emergency service providers. (→P. 472) *: U.S. Patent No. 7,508,298 B2

● Stolen Vehicle Location

Helps drivers in the event of vehicle theft. (→P. 473)

● Emergency Assistance Button (SOS)

Connects drivers to response-center support. (→P. 473)

● Enhanced Roadside Assistance

Provides drivers various on-road assistance. (→P. 473)

■ Subscription

After you have signed the Telematics Subscription Service Agreement and are enrolled, you can begin receiving services. A variety of subscription terms is available for purchase. Contact your Toyota dealer, call 1-800-331-4331, or push the “SOS” but- ton in your vehicle for further subscription details.

470

3-7. Other interior features

■Safety Connect Services Information

●Phone calls using the vehicles Bluetooth® technology will not be possible

during Safety Connect.

●Safety Connect is available beginning Fall 2009 on select Toyota models. Contact with the Safety Connect response center is dependent upon the telematics device being in operative condition, cellular connection avail- ability, and GPS satellite signal reception, which can limit the ability to reach the response center or receive emergency service support. Enroll- ment and Telematics Subscription Service Agreement required. A variety of subscription terms is available; charges vary by subscription term selected.

●Safety Connect services will function in the United States, including Hawaii and Alaska, and in Canada. The services will not function outside of the United States in countries other than Canada. For details about the service, contact your Toyota dealer.

●Safety Connect services are not subject to section 255 of the Telecom-

munications Act and the device is not TTY compatible.

■Languages

The Safety Connect response center will offer support in multiple languages. The Safety Connect system will offer voice prompts in English and Spanish. Please indicate your language of choice when enrolling.

■When contacting the response center

You may be unable to contact the response center if the network is busy.

471

3-7. Other interior features

Safety Connect LED light Indicators

When the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system) or the engine switch is turned to the “ON” position (vehicles without a smart key system), the red indicator light comes on for 2 seconds then turns off. Afterward, the green indicator light comes on, indicating that the service is active. The following indicator light patterns indicate specific system usage conditions: ● Green indicator light on = Active service ● Green indicator light flashing = Safety Connect call in process ● Red indicator light (except at vehicle start-up) = System malfunc-

tion (contact your Toyota dealer)

● No indicator light (off) = Safety Connect service not active

Safety Connect services

■ Automatic Collision Notification

In case of either airbag deployment or severe rear-end collision, the system is designed to automatically call the response center. The responding agent receives the vehicle’s location and attempts to speak with the vehicle occupants to assess the level of emer- gency. If the occupants are unable to communicate, the agent automatically treats the call as an emergency, contacts the nearest emergency services provider to describe the situation, and requests that assistance be sent to the location.

472

3-7. Other interior features

■ Stolen Vehicle Location

If your vehicle is stolen, Safety Connect can work with local author- ities to assist them in locating and recovering the vehicle. After fil- ing a police report, call the Safety Connect response center at 1- 800-331-4331 and follow the prompts for Safety Connect to initiate this service. In addition to assisting law enforcement with recovery of a stolen vehicle, Safety-Connect-equipped vehicle location data may, under certain circumstances, be shared with third parties to locate your vehicle. Further information is available at Toyota.com.

■ Emergency Assistance Button (“SOS”)

In the event of an emergency on the road, push the “SOS” button to reach the Safety Connect response center. The answering agent will determine your vehicle’s location, assess the emer- gency, and dispatch the necessary assistance required. If you accidentally press the “SOS” button, tell the response-center agent that you are not experiencing an emergency.

■ Enhanced Roadside Assistance

Enhanced Roadside Assistance adds GPS data to the already included warranty-based Toyota roadside service. Subscribers can press the “SOS” button to reach a Safety Connect response-center agent, who can help with a wide range of needs, such as: towing, flat tire, fuel delivery, etc. For a description of the Enhanced Roadside Assistance services and their limitations, please see the Safety Connect Terms and Conditions, which are available at Toyota.com.

473

3-7. Other interior features

Safety information for Safety Connect

Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals

The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for mobile wire- less phones. Those guidelines are consistent with the safety stan- dards previously set by the following U.S. and international standards bodies. ● ANSI (American National Standards Institute) C95.1 [1992] ● NCRP (National Council on Radiation Protection and Measure-

ment) Report 86 [1986]

● ICNIRP (International Commission on Non-Ionizing Radiation

Protection) [1996]

Those standards were based on comprehensive and periodic eval- uations of the relevant scientific literature. Over 120 scientists, engineers, and physicians from universities, and government health agencies and industries reviewed the available body of research to develop the ANSI Standard (C95.1). The design of Safety Connect complies with the FCC guidelines in addition to those standards.

474

3-7. Other interior features

■License

Licensed by QUALCOMM Incorporated under one or more of the following United States Patents and/or their counterparts in other nations: 4,901,307 5,490,165 5,056,109 5,504,773 5,101,501
5,506,865 5,109,390 5,511,073 5,228,054 5,535,239
5,267,261 5,544,196 5,267,262 5,568,483 5,337,338
5,600,754 5,414,796 5,657,420 5,416,797 5,659,569
5,710,784 5,778,338

■Certification for Safety Connect

FCC ID: O9EGTM1
FCC ID: O6Y-CDMRF101
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

475

3-7. Other interior features

476

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition:

● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.

● Wash the vehicle body using a sponge or soft cloth, such as a

chamois.

● For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

● Wipe away any water. ● Wax the vehicle when the waterproof coating deteriorates.

If water does not bead on a clean surface, apply wax when the vehi- cle body is cool.

■Automatic car washes

●Fold the mirrors and remove the detachable pole antenna before wash- ing the vehicle. Start washing from the front of the vehicle. Make sure to re-install the antenna and extend the mirrors before driving.

●Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle’s paint.

●In certain automatic car washes, the roof antenna (if equipped) or rear spoiler may interfere with machine operation. This may prevent the vehi- cle from being cleaned properly or result in damage to the antenna or rear spoiler.

■High pressure car washes

●Do not allow the nozzles of the car wash to come within close proximity

of the windows.

●Before using the car wash, check that the fuel filler door on your vehicle

is closed properly.

478

4-1. Maintenance and care

■Aluminum wheels (if equipped)

●Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.

●Do not use detergent on the wheels when they are hot, for example after

driving for long distance in the hot weather.

●Wash detergent from the wheels immediately after use.

■Bumpers and side moldings

Do not scrub with abrasive cleaners.

CAUTION

■When washing the vehicle

Do not apply water to the inside of the engine compartment. Doing so may cause the electrical components etc. to catch fire.

■Precautions regarding the exhaust pipe

Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.

479

4-1. Maintenance and care

NOTICE

■To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.) ●Wash the vehicle immediately in the following cases:

• After driving near the sea coast • After driving on salted roads • If coal tar or tree sap is present on the paint surface • If dead insects, insect droppings or bird droppings are present on the

paint surface

• After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled with dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface

●If the paint is chipped or scratched, have it repaired immediately. ●To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

■Cleaning the exterior lights

●Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

●Do not apply wax on the surfaces of the lights.

Wax may cause damage to the lenses.

■Detachable pole antenna installation and removal precautions

●Before driving, ensure that the antenna is installed. ●When the antenna is removed, such as before entering an automatic car wash, make sure to store it in a suitable place so as not to lose it. Also, before driving, make sure to reinstall the antenna in its original position. ■High pressure car washes (vehicles with rear view monitor system)

When washing the vehicle, do not apply intensive bursts of water to the cam- era or camera area. Doing so may result in the camera malfunctioning.

480

4-1. Maintenance and care Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.

■ Cleaning the leather areas

● Remove dirt and dust using a vacuum cleaner. ● Wipe off any excess dirt and dust with a soft cloth dampened

with diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.

● Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

● Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded and venti- lated area.

■ Cleaning the synthetic leather areas

● Remove loose dirt using a vacuum cleaner. ● Apply a mild soap solution to the synthetic leather using a

sponge or soft cloth.

● Allow the solution to soak in for a few minutes. Remove the

dirt and wipe off the solution with a clean, damp cloth.

481

4-1. Maintenance and care

■Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.

■Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not use water. Wipe dirty surfaces and let them dry. Excellent results are obtained by keeping the carpet as dry as possible.

■Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.

CAUTION

■Water in the vehicle

●Do not splash or spill liquid in the vehicle.

Doing so may cause electrical components etc. to malfunction or catch fire.

●Do not get any of the SRS components or wiring in the vehicle interior wet.

(→P. 115) An electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or serious injury.

■Cleaning the interior (especially instrument panel)

Do not use polish wax or polish cleaner. The instrument panel may reflect off the windshield, obstructing the driver’s view and leading to an accident, resulting in death or serious injury.

482

4-1. Maintenance and care

NOTICE

■Cleaning detergents

●Do not use the following types of detergent, as they may discolor the vehi-

cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline,

alkaline or acidic solutions, dye, and bleach.

• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-

hol.

●Do not use polish wax or polish cleaner. The instrument panel’s or other

interior part’s painted surface may be damaged.

■Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of leather surfaces: ●Remove any dust or dirt from leather surfaces immediately. ●Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

●Do not place items made of vinyl, plastic, or containing wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.

■Water on the floor

Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components such as the audio system above or under the floor of the vehicle. Water may also cause the body to rust.

■Cleaning the inside of the back window

●Do not use glass cleaner to clean the back window, as this may cause damage to the rear window defogger heater wires. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires.

●Be careful not to scratch or damage the heater wires.

483

4-2. Maintenance Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular maintenance are essential. It is the owner’s responsibility to perform regular checks. Toyota recommends performing the following main- tenance: ■ General maintenance

General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.

■ Scheduled maintenance

Scheduled maintenance should be performed at specified inter- vals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

■ Do-it-yourself maintenance

You can perform some maintenance procedures by yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals is recommended. For details about warranty coverage, see the separate “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement”.

■Repair and replacement

It is recommended that genuine Toyota parts be used for repairs to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.

484

4-2. Maintenance

■Allow inspection and repairs to be performed by a Toyota dealer

●Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.

●Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.

CAUTION

■If your vehicle is not properly maintained

Improper maintenance could result in serious damage to the vehicle and possible serious injury or death.

■Handling of the battery

●Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.

●Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.

●Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 509)

485

4-2. Maintenance General maintenance

Listed below are the general maintenance items that should be per- formed at the intervals specified in the “Owner's Warranty Informa-