2009 Nissan Murano Owners Manual

To open, push the knob *1 and pull out *2 .

Rear

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (113,1)

CARGO FLOOR BOX Type A 1. To open the cargo floor box, pull the strap *A .

2. Remove the strap *B from the back side of the board and hang it on the opening of the lift gate.

Type B To open the cargo floor box, push *A . To close, push the lid until the lock latches. The net partitions can be removed *B to make a larger storage space.

The cargo floor box needs to be removed when you need a spare tire. (See “FLAT TIRE” in the “6. In case of emergency” section.)

CAUTION

To avoid damage, do not load more then 22 lbs (10 kg) of cargo into the cargo floor box.

SIC3593

STORAGE BOX (if so equipped) To open, push the storage box lid *1
illustrated. The inner tray can be removed *2 as illustrated. Do not place valuable items in the storage box.

as

Do not use the storage box as an ashtray.

Type A

SIC3655

Type B

SIC3656

Instruments and controls 2-45

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (114,1)

To use the sub cover, hang the straps on the back of the head restraint *2 . To stow the cargo cover, remove it from the hooks and hold until it is retracted.

To remove the cargo cover, stow the cover and pull the left side of the holder to the opposite side *3 .

WARNING

. Never put anything on the cargo cover, no matter how small. Any object on it could cause an injury in an accident or sudden stop.

. Close the cargo cover when folding

the rear seat.

. Do not leave the cargo cover in the vehicle with it disengaged from the holder.

. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unse- cured cargo could cause personal injury.

. Your child could be seriously injured or killed in a collision if the child

Model "Z51-D" EDITED: 2007/ 10/ 2

LUGGAGE SIDE BOX To open the luggage side box, pull up the strap.

SIC3594

SIC3595

CARGO COVER (if so equipped) The cargo cover keeps the contents in the cargo area hidden from the outside.

To use the cargo cover, pull it out and hang both sides on the hooks *1 .

2-46 Instruments and controls

restraint top tether strap is da- maged.

— If the cargo cover contacts the top tether strap when it is at- tached to the top tether anchor, remove the cargo cover from the vehicle or secure it on the cargo floor below its attachment loca- tion. If the cargo cover is not removed, it may damage the top tether strap during a collision.

— Do not allow cargo to contact the top tether strap when it is attached to the top tether an- chor. Properly secure the cargo so it does not contact the top tether strap. Cargo that is not properly secured or that con- tacts the top tether strap may damage the top tether strap during a collision.

Black plate (115,1)

ropes and hooks.

. Unsecured cargo can become dan- gerous in an accident or sudden stop.

CAUTION

Do not apply a total load of more than 22 lb (10 kg) *A or 7 lb (3 kg) *B to a single hook.

LUGGAGE HOOKS (if so equipped)

SIC3596

WARNING

. Always make sure that the cargo is properly secured. Use the suitable

Instruments and controls 2-47

Model "Z51-D" EDITED: 2007/ 10/ 2

information” section.

WARNING

. Drive extra carefully when the vehi- cle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack.

. Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sud- den or unusual handling maneuvers. . Roof rack load should be evenly

distributed.

. Do not exceed maximum roof rack

load weight capacity.

. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

CAUTION

Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof

SIC3597

ROOF RACK (if so equipped) Always distribute the luggage evenly on the roof rack. Do not load more than 165 lb (75 kg) on the roof rails. Observe the maximum load limit shown on the crossbars or roof carriers when you attach them on the roof rails. Contact a NISSAN dealer for crossbar or other equipment information. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. or C.V.M.S.S. certification label (located on the driver’s door pillar). For more information regarding GVWR and GAWR, see “VEHICLE LOADING INFOR- MATION” in the “9. Technical and consumer 2-48 Instruments and controls

Black plate (116,1)

rack from the ground, use a ladder or stool.

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (117,1)

WINDOWS

POWER WINDOWS

WARNING

. Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the win- dow lock switch to prevent unex- pected use of the power windows.

. Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols and become trapped in the window. Unattended children could become involved in serious acci- dents.

The power windows operate when the ignition switch is in the ON position or for about 45
seconds after the ignition switch is pushed to the OFF position. front passenger’s door is opened during this period of about 45 seconds, power to the windows is canceled.

the driver’s or

If

Instruments and controls 2-49

Model "Z51-D" EDITED: 2007/ 10/ 2

SIC3505

SIC3657

COAT HOOKS The coat hooks are equipped beside the rear personal lights.

CAUTION

Do not place items which are more than 2 lb (1 kg) on the hook.

CARGO NET (if so equipped) The cargo net helps keep packages in the cargo area from moving around while your vehicle is driven.

To install the cargo net, attach the hooks to the retainers *A .

CAUTION

Avoid keeping heavy objects in the net.

Black plate (118,1)

Locking passengers’ windows When the lock button *C is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.

SIC3283A

Front passenger side window

Main power window switch (driver’s side) 1. Driver side window 2. 3. Rear left passenger side window 4. Rear right passenger side window 5. Window lock button To open or close the window, push down *A or pull up *B the switch and hold it. The main switch (driver side switches) will open or close all the windows.

2-50 Instruments and controls

SIC3241

Passenger side power window switch The passenger side switch will open or close only the corresponding window. To open or close the window, push down or pull up the switch and hold it.

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (119,1)

Auto reverse function

1. Push the ignition switch to the ON position.

WARNING

There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the window.

If the control unit detects something caught in the window as it is closing, the window will be immediately lowered.

The auto reverse function can be activated when the window is closed by automatic operation when the ignition switch is in the ON position or for 45 seconds after the ignition switch is pushed to the OFF position.

Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the window occurs.

If the windows do not close automatically If the power window automatic function (closing only) does not operate properly, perform the following procedure to initialize the power window system.

2. Close the door.

3. Open the window more than halfway by

operating the power window switch.

4. Pull the power window switch and hold it to close the window, and then hold the switch more than 3 seconds after the window is closed completely.

5. Release the power window switch. Operate the window by the automatic function to confirm the initialization is complete.

6. Perform steps 2 through 5 above for other

windows.

If the power window automatic function does not operate properly after performing the pro- cedure above, have your vehicle checked by a NISSAN dealer.

Instruments and controls 2-51

Model "Z51-D" EDITED: 2007/ 10/ 2

SIC3285

Automatic operation (for front door win- dows) To fully open or close the window, completely push down or pull up the switch and release it; it need not be held. The window will automatically open or close all the way. To stop the window, just push or the switch in the opposite direction.

lift

A light push or pull on the switch will cause the window to open or close until the switch is released.

AUTOMATIC MOONROOF AND SUN- SHADES The moonroof and sunshades only operates when the ignition switch is in the ON position.

The automatic moonroof and sunshades are operational for about 45 seconds, even if the ignition switch is pushed to the OFF position. If the driver’s door or the passenger’s door is opened during this period of about 45 seconds, power to the moonroof and sunshades is canceled.

MOONROOF (if so equipped)

WARNING

In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.

. Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.

CAUTION

. Remove water drops, snow, ice or sand from the moonroof before opening.

. Do not place any heavy object on the moonroof or surrounding area. . Do not push or pull on the sun- shade. Doing so can damage the sunshade.

2-52 Instruments and controls

Black plate (120,1)

SIC3598

of

Sliding sunshade and moonroof When the OPEN side *1
the moonroof switch is pushed, the front and rear sunshades will fully open. When the switch is pushed again, the moonroof will fully open. When the CLOSE side *2
of the moonroof switch is pushed, the moonroof will automati- cally close. Push the switch again, and the front and rear sunshades will close.

When the OPEN or CLOSE side of the moon- roof switch is pushed to the second detent (*3
or *4 ), both the sunshade and moonroof will open or close.

To stop the sunshades or moonroof during the

Model "Z51-D" EDITED: 2007/ 10/ 2

operation, push either of the OPEN *1 , CLOSE *2 or UP *5 of the switch. Tilting moonroof To tilt up the moonroof, push the moonroof switch to the up position *5 . To tilt down the moonroof, push the switch to the up position *5 or push the CLOSE side *2 of the switch.

When the moonroof is tilted up, push the CLOSE side of the moonroof switch to the second detent *4 . The moonroof will tilt down and the sunshades will close.

Auto reverse function

WARNING

There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the moonroof.

If the control unit detects something caught in the moonroof and sunshades when they are closing, the moonroof will be immediately opened.

The auto reverse function can be activated when

the moonroof and sunshades are closed by automatic operation when the ignition switch is in the ON position or for about 45 seconds after the ignition switch is pushed to the OFF position.

If the moonroof and sunshades cannot be closed automatically when the auto reverse function activates due to a malfunction, push and hold the CLOSE side *2 of the moonroof switch.

Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.

If the moonroof does not operate If the moonroof does not operate properly, perform the following procedure to initialize the moonroof operation system.

1.

If the moonroof is open, close it fully by pushing the CLOSE side *2 of the moon- roof switch.

2. Push and hold the CLOSE side *2 of the

moonroof switch.

3. Release the moonroof switch after

the moonroof or sunshade moves slightly to the closed position.

4. Push and hold the CLOSE side *2 of the

Black plate (121,1)

moonroof switch for 10 seconds.

5. The moonroof and sunshades will fully open

and then close.

6. Check if normally.

the moonroof switch operates

If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer.

Instruments and controls 2-53

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (122,1)

INTERIOR LIGHTS

SIC3249

SIC3250

SIC3251

MAP LIGHTS Push the button as illustrated to turn the light on or off.

PERSONAL LIGHTS Rear Push the button as illustrated to turn the light on or off.

INTERIOR LIGHT CONTROL SWITCH The interior light control switch has three positions: ON, DOOR and OFF.

ON position When the switch is in the ON position *1
map lights and rear personal nate.

lights will

the illumi-

2-54 Instruments and controls

DOOR position When the switch is in the DOOR position *2 , the map lights and rear personal lights will illuminate under the following conditions:

ignition switch is switched to the LOCK position

Model "Z51-D" EDITED: 2007/ 10/ 2

.

— remain on for about 15 seconds.

doors are unlocked by pushing the UN- LOCK button on the Intelligent Key or door handle request switch with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened and then closed with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened with the ignition switch in the ACC or ON position

— remain on while the door

is opened. When the door is closed, the lights go off.

The lights will also turn off after 30
minutes when the lights remain illumi- nated after the ignition switch has been pushed to the OFF or LOCK position to prevent the battery from becoming dis- charged.

When the auto interior illumination is set to the OFF position (see “VEHICLE INFORMATION AND SETTINGS” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section), the lights will illuminate under the following condition:

any door is opened with the ignition switch in any position

Black plate (123,1)

MOOD LIGHTS

— remain on while the door

is opened. When the door is closed, the lights go off.

OFF position When the switch is in the OFF position *3 , the lights will not the condition.

regardless of

illuminate,

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

Map lights

SIC3599

Ceiling

SIC3600

Instruments and controls 2-55

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (124,1)

VANITY MIRROR LIGHTS

CARGO LIGHTS

The mood lights *A located in the following positions will illuminate whenever the headlight switch is in the

next to the map lights

position.

or

on the rear ceiling

under the instrument panel

under the driver’s power window switch

The mood lights can be adjusted with the illumination control buttons.

See “Instrument brightness control” earlier in this section.

SIC2064

The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.

When the cover is closed, the light will turn off.

The lights will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.

SIC2131A

When the switch is in the ON position *1 , the light illuminates while the lift gate is opened. When the lift gate is closed, the light will turn off. When the switch is in the OFF position *2 , the light will turn off.

The lights will turn off after 30 minutes when the light remain illuminated to pre- vent the battery from becoming dis- charged.

2-56 Instruments and controls

Model "Z51-D" EDITED: 2007/ 10/ 2

HomeLink® UNIVERSAL TRANSCEIVER (if so equipped)

HomeLink® Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink® Universal Transceiver: . Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.

Is powered by your vehicle’s battery. No separate batteries are required. the vehicle’s battery is discharged or is dis- connected, HomeLink® will retain all pro- gramming.

If

Once HomeLink® Universal Transceiver is programmed, retain the original transmit- ter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink® Universal Transceiver buttons should be erased for security purposes. For additional information, see “PRO- GRAMMING HomeLink®” later in this sec- tion.

the vehicle,

WARNING

. Do not use HomeLink® Universal Transceiver with any garage door opener that lacks safety stop and

reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982.) A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.

. During programming procedure, your garage door or security gate may open or close. Make sure that people and objects are clear of the garage door, gate, etc. that you are programming.

. Your vehicle’s engine should be turned off while programming HomeLink® Universal Transceiver.

PROGRAMMING HomeLink® To program your HomeLink® Transceiver to operate a garage door, gate, or entry door opener, home or office lighting, you need to be at the same location as the device. Note: Garage door openers (manufactured after

Black plate (125,1)

1996) have “rolling code protection”. To pro- gram a garage door opener equipped with “rolling code protection”; you will need to use a ladder to get up to the garage door opener motor to be able to access the “smart or learn” program button.

Instruments and controls 2-57

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (126,1)

5.

button - releasing when the device begins to activate. If the indicator light on HomeLink® blinks rapidly for two seconds and then turns solid, HomeLink® has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train Home- Link®, completing the programming may require a ladder and another person for convenience.

6. Push and release the program button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. the wire originates from under a light lens, you will need to remove the lens to access the training button.

If

NOTE: Once you have pushed and released the training button on the garage door open- er’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. For convenience, use the help of a second person to assist when performing this step. 7. Quickly (within 30 seconds of pushing and releasing the garage door opener training button) and firmly push and release the HomeLink® button you’ve just programmed.

Model "Z51-D" EDITED: 2007/ 10/ 2

SIC3612

SIC3613

1. To begin, push and hold the 2 outer Home- Link® buttons (to clear the memory) until the indicator light *A blinks (after 20 seconds). Release both buttons.

3. Using both hands, simultaneously push and hold both the HomeLink® button you want to program and the hand-held transmitter button.

2. Position the end of the hand-held transmitter 1 to 3 in (20 to 70 mm) away from the HomeLink® surface.

DO NOT release the buttons until step 4 has been completed.

4. Hold down both buttons until the indicator light on HomeLink® flashes, changing from a “slow blink” to a “rapid blink”. This could take up to 90 seconds. When the indicator light blinks rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, push and hold the programmed HomeLink®

2-58 Instruments and controls

Push and release the HomeLink® button up to three times to complete the training.

8. Your HomeLink® button should now be programmed. To program the remaining HomeLink® buttons for additional door or gate openers, follow steps 2 through 8 only.

NOTE: Do not repeat step 1 unless you want to “clear” all previously programmed Home- Link® buttons.

If you have any questions or are having difficulty programming your HomeLink® buttons, please to the HomeLink® web site at: www. refer homelink.com or call 1-800-355-3515.

to 1992, D.O.C.

PROGRAMMING HomeLink® FOR CA- NADIAN CUSTOMERS Prior regulations required hand-held transmitters to stop transmitting after 2 seconds. To program your hand-held trans- mitter to HomeLink®, continue to push and hold the HomeLink® button (note steps 2 through 4
under “Programming HomeLink®”) while you push and re-push (“cycle”) your hand-held transmitter every 2 seconds until the indicator light flashes rapidly (indicating successful pro- gramming).

NOTE: If programming a garage door opener, etc.,

it is advised to unplug the device during the “cycling” process to prevent possible damage to the garage door opener com- ponents.

OPERATING THE HomeLink® UNIVER- SAL TRANSCEIVER HomeLink® Universal Transceiver (once pro- grammed) may now be used to activate the garage door, etc. To operate, simply push the appropriate programmed HomeLink® Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted.

PROGRAMMING TROUBLE-DIAGNO- SIS If HomeLink® does not quickly learn the hand- held transmitter information:

replace the hand-held transmitter batteries with new batteries.

position the hand-held transmitter with its battery area facing away from the Home- Link® surface. push and hold both the HomeLink® and hand-held transmitter buttons without inter- ruption.

position the hand-held transmitter 2 to 5 in (50 to 127 mm) away from the HomeLink® surface. Hold the transmitter in that position

Black plate (127,1)

for up to 15 seconds. If HomeLink® is not programmed within that time, try holding the transmitter in another position - keeping the indicator light in view at all times.

If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this Owner’s Manual.

CLEARING THE PROGRAMMED IN- FORMATION Individual buttons cannot be cleared, however to clear all programming, push and hold the two outside buttons and release when the indicator light begins to flash (in approximately 20
seconds).

REPROGRAMMING A SINGLE Home- Link® BUTTON To reprogram a HomeLink® Universal Transcei- ver button, complete the following. 1. Push and hold the desired HomeLink® button. Do not release the button until step 4 has been completed.

2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 2 to 5 in (50 to 127
mm) away from the HomeLink® surface.

3. Push and hold the hand-held transmitter

Instruments and controls 2-59

Model "Z51-D" EDITED: 2007/ 10/ 2

may be received, that may cause undesired operation.

including interference

The transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

DOC: ISTC 1763K1313

FCC I.D.: CB2V67690

button.

4. The HomeLink® indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.

The HomeLink® Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLink® button that was just programmed. This procedure will not affect any other programmed HomeLink® buttons.

IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLink®. Consult the Owner’s Manual of each device or call the those devices for manufacturer or dealer of additional information.

When your vehicle is recovered, you will need to reprogram the HomeLink® Univer- sal Transceiver with your new transmitter information.

FCC Notice:

This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that

2-60 Instruments and controls

Black plate (128,1)

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (10,1)

3 Pre-driving checks and adjustments

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN Vehicle Immobilizer System keys . . . . . . . . . . . . 3-2
Intelligent Key system (if so equipped) . . . . . . . . . . . . . . . . 3-3
Mechanical key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Valet hand-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Locking with mechanical key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Opening and closing windows with the mechanical key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Locking with power door lock switch . . . . . . . . . . . . . . . . . . 3-6
Vehicle speed sensing door lock mechanism . . . . . . . . 3-6
Automatic door unlock mechanism . . . . . . . . . . . . . . . . . . . . . 3-6
Child safety rear door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Intelligent Key system (if so equipped) . . . . . . . . . . . . . . . . . . . . 3-7
Intelligent Key operating range . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Door locks/unlocks precaution . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Intelligent Key operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Battery saver system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Warning signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Remote keyless entry system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
How to use remote keyless entry system . . . . . . . . . . . 3-15

Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Operating manual lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Operating power lift gate (if so equipped) . . . . . . . . . . 3-19
Auto closure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Lift gate release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Opening fuel-filler door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Tilting telescopic steering column . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Manual operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Electric operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Inside mirror. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Outside mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Vanity mirror. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Automatic drive positioner (if so equipped). . . . . . . . . . . . . 3-30
Entry/exit function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Memory storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
System operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31

Model "Z51-D" EDITED: 2007/ 10/ 2

KEYS

A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record any key numbers so it is very important to keep track of your key number plate.

A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by a NISSAN dealer.

Type A

SPA2406

3-2 Pre-driving checks and adjustments

Type B

SPA2431

Black plate (132,1)

1. Master key (2) 2. Mechanical key (inside the key) (2) 3. Key number plate (1) NISSAN VEHICLE IMMOBILIZER SYS- TEM KEYS Your vehicle can only be driven with the master keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head.

Never leave these keys in the vehicle.

Additional or replacement keys:

If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can duplicate your existing key. As many as 4 keys can be used with one vehicle. You should bring all the registered keys that you have to a NISSAN dealer for registration. This is because the registration process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System. After the registration process, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle.

Model "Z51-D" EDITED: 2007/ 10/ 2

CAUTION

Do not allow the NISSAN Vehicle Im- mobilizer System key, which contains an electrical transponder, to come in contact with salt water. This could cause the system to malfunction.

INTELLIGENT KEY SYSTEM (if so equipped) Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle’s Intelligent Key system components and NISSAN Vehicle Immobilizer System compo- nents. As many as 4 Intelligent Keys can be registered and used with one vehicle. The new keys must be registered by a NISSAN dealer prior to use with the Intelligent Key system and NISSAN Vehicle Immobilizer System of your vehicle. Since the registration process requires erasing all memory in the Intelligent Key compo- nents when registering new keys, be sure to take all Intelligent Keys that you have to the NISSAN dealer.

CAUTION

. Be sure to carry the Intelligent Key with you when driving. The Intelli- gent Key is a precision device with a

built-in transmitter. To avoid dama- ging it, please note the following.

— The Intelligent Key is water resistant; however, wetting may damage the Intelligent Key. If the Intelligent Key gets wet, immediately wipe until it is com- pletely dry.

— Do not bend, drop or strike it

against another object.

— Do not place the Intelligent Key for an extended period in a place where temperatures ex- ceed 1408F (608C).

— Do not change or modify the

Intelligent Key.

— Do not use a magnet key holder. — Do not place the Intelligent Key near an electric appliance such as a television set or personal computer.

— Do not allow the Intelligent Key to come into contact with water or salt water, and do not wash it in a washing machine. This could affect the system function. If an Intelligent Key is lost or stolen, NISSAN recommends erasing the ID

Black plate (133,1)

code of that Intelligent Key. This will prevent the Intelligent Key from unauthorized use to unlock the vehicle. For information regarding the erasing procedure, please con- tact a NISSAN dealer.

Pre-driving checks and adjustments 3-3

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (134,1)

DOORS

CAUTION

WARNING

Always carry the mechanical key in- stalled in the key.

VALET HAND-OFF When you have to leave a key with a valet, give them the key itself after removing the mechanical key to protect your belongings.

To prevent the glove box from being opened during valet hand-off, follow the procedures below.

SPA2033

1. Remove the mechanical key from the key.

2. Lock the glove box with the mechanical key.

3. Hand the key to the valet, keeping the mechanical key in your pocket or bag. Insert the mechanical key into the key when you retrieve your vehicle.

For glove box lock, see “STORAGE” in the “2. Instruments and controls” section.

MECHANICAL KEY To remove the mechanical key, release the lock knob at the back of the key.

To install the mechanical key, firmly insert it into the key until the lock knob returns to the lock position.

Use the mechanical key to lock or unlock the doors and glove box, if they are equipped with a key cylinder.

See “DOORS” later in this section and “STO- RAGE” in the “2. Instruments and controls” section.

3-4 Pre-driving checks and adjustments

. Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders.

. Before opening any door, always look for and avoid oncoming traffic. . Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.

Model "Z51-D" EDITED: 2007/ 10/ 2

SETTING BUTTON” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.)

OPENING AND CLOSING WINDOWS WITH THE MECHANICAL KEY The driver’s door key operation also allows you to open and close all door windows.

To open the windows, turn the driver’s door key cylinder to the rear of the vehicle for longer than 1 second. The door is unlocked and the window keeps opening while turning the key.

This function can also be performed by pushing and holding the door UNLOCK button of the key. (See “REMOTE KEYLESS ENTRY SYS- TEM” later in this section.)

To close the windows, turn the driver’s door key cylinder to the front of the vehicle for longer than 1 second. The door is locked and the window keeps closing while turning the key.

Black plate (135,1)

SPA2465

LOCKING WITH INSIDE LOCK KNOB To lock the door individually, move the inside lock knob to the lock position *1
then close the door.

To unlock, move the inside lock knob to the unlock position *2 . When locking the door without a key, be sure not to leave the key inside the vehicle.

Pre-driving checks and adjustments 3-5

Model "Z51-D" EDITED: 2007/ 10/ 2

SPA2432

LOCKING WITH MECHANICAL KEY The power door lock system allows you to lock or unlock all doors simultaneously using the mechanical key.

Turning the driver’s door key cylinder to the front of the vehicle *1 will lock all doors. Turning the driver’s door key cylinder once to the rear of the vehicle *2 will unlock the driver’s door. After returning the key to the neutral position *3 , turning it to the rear again within 1 minute will unlock all doors. . You can switch the lock system to the mode that allows you to open all the doors when the key is turned once. (See “HOW TO USE

Black plate (136,1)

Lockout protection When the power door lock switch (driver or front passenger) is moved to the lock position with the key in the port and any door open, all doors will lock and unlock automatically. With the Intelligent Key left in the vehicle (not in the key port) and any door open, all doors will unlock automatically and a chime will sound after the door is closed.

These functions help to prevent the key from being accidentally locked inside the vehicle.

VEHICLE SPEED SENSING DOOR LOCK MECHANISM All doors will be locked automatically when the vehicle speed reaches 15 MPH (24 km/h).

To activate or deactivate the vehicle speed sensing door lock mechanism, perform the following procedure.

1. Close all doors.

2. Push the ignition switch to the “ON”

position.

3. Within 20 seconds, push and hold the lock switch to the “LOCK”

power door position for more than 5 seconds.

4. When activated,

the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once.

A NISSAN dealer can customize this function to lock the doors when the selector lever is moved to any other position from the P (Park) position. Contact a NISSAN dealer for details.

AUTOMATIC DOOR UNLOCK ME- CHANISM All doors will be unlocked automatically when the ignition switch is pushed to the OFF position.

To activate or deactivate the automatic door unlock mechanism, perform the following pro- cedure.

1. Close all doors.

2. Push the ignition switch to the “ON”

position.

3. Within 20 seconds, push and hold the power door lock switch to the “UNLOCK” position for more than 5 seconds.

4. When activated,

the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once.

A NISSAN dealer can customize this function to unlock the doors when the selector lever is moved to the P (Park) position from the other positions. Contact a NISSAN dealer for details.

Model "Z51-D" EDITED: 2007/ 10/ 2

SPA2300

LOCKING WITH POWER DOOR LOCK SWITCH Operating the power door lock switch will lock or unlock all the doors. The switches are located on the driver’s and front passenger’s door armrests.

To lock the doors, push the power door lock switch to the lock position *1 with the driver’s or front passenger’s door open, then close the door.

When locking the door this way, be certain not to leave the key inside the vehicle.

To unlock the doors, push the power door lock switch to the unlock position *2 . 3-6 Pre-driving checks and adjustments

INTELLIGENT KEY SYSTEM (if so equipped)

WARNING

Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufac- turer for the possible influences before use.

The Intelligent Key system can operate all the door locks using the remote controller function or pushing the request switch on the vehicle without taking the key out from a pocket or purse. The operating environment and/or condi- tions may affect the Intelligent Key system operation.

Be sure to read the following before using the Intelligent Key system.

CAUTION

. Be sure to carry the Intelligent Key with you when operating the vehi- cle.

. Never leave the Intelligent Key in the vehicle when you leave the vehicle.

The Intelligent Key is always communicating with

Black plate (137,1)

the vehicle as it receives radio waves. The Intelligent Key system transmits weak radio waves. Environmental conditions may interfere with the operation of the Intelligent Key system under the following operating conditions. . When operating near a location where strong radio waves are transmitted, such as a TV tower, power station and broad- casting station.

. When in possession of wireless equipment, transceiver,

such as a cellular telephone, and CB radio.

. When the Intelligent Key is in contact with or

covered by metallic materials.

. When any type of radio wave remote control

is used nearby.

. When the Intelligent Key is placed near an electric appliance such as a personal computer.

. When the vehicle is parked near a parking

meter.

In such cases, correct the operating conditions before using the Intelligent Key function or use the mechanical key.

Although the life of the battery varies depending on the operating conditions, the battery’s life is approximately 2 years. the battery is dis-

If

Pre-driving checks and adjustments 3-7

Model "Z51-D" EDITED: 2007/ 10/ 2

SPA2433

CHILD SAFETY REAR DOOR LOCK The child safety rear door lock helps prevent doors from being opened accidentally, espe- cially when small children are in the vehicle.

When the levers are in the lock position *1 , the rear doors can be opened only from the outside.

To disengage, move the levers to the unlock position *2 .

charged, replace it with a new one.

Since the Intelligent Key is continuously receiv- ing radio waves, if the key is left near equipment which transmits strong radio waves, such as signals from a TV and personal computer, the battery life may become shorter.

information regarding replacement of a For battery, see “BATTERY REPLACEMENT” in the “8. Maintenance and do-it-yourself” section.

Because the steering wheel is locked electri- cally, unlocking the steering wheel with the ignition switch in the LOCK position is impos- sible when the vehicle battery is completely discharged. Pay special attention that the vehicle battery is not completely discharged.

As many as 4 Intelligent Keys can be registered and used with one vehicle. For information about the purchase and use of additional Intelligent Keys, contact a NISSAN dealer.

CAUTION

. Do not allow the Intelligent Key, which contains electrical compo- nents, to come into contact with water or salt water. This could affect the system function.

. Do not drop the Intelligent Key.

3-8 Pre-driving checks and adjustments

. Do not strike the Intelligent Key

sharply against another object.

. Do not change or modify the Intel-

ligent Key.

. Wetting may damage the Intelligent Key. If the Intelligent Key gets wet, immediately wipe until it is comple- tely dry.

. Do not place the Intelligent Key for an extended period in an area where temperatures exceed 1408F (608C). . Do not attach the Intelligent Key with a key holder that contains a magnet.

. Do not place the Intelligent Key near equipment that produces a mag- netic field, such as a TV, audio equipment and personal computers.

If an Intelligent Key is lost or stolen, NISSAN recommends erasing the ID code of that Intelligent Key from the vehicle. This may prevent the unauthorized use of the Intelligent Key to operate the vehicle. For information regarding the erasing procedure, contact a NISSAN deal- er.

Black plate (138,1)

SPA1948A

INTELLIGENT KEY OPERATING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range *1
When the Intelligent Key battery is discharged or

from the request switch.

Model "Z51-D" EDITED: 2007/ 10/ 2

strong radio waves are present near the operat- ing location, the Intelligent Key system’s operat- ing range becomes narrower, and the Intelligent Key may not function properly. The operating range *1
cm) from each request switch.

is within 31.50 in (80

If the Intelligent Key is too close to the door glass, handle or the request switches may not function.

rear bumper

When the Intelligent Key is within the operating range, it is possible for anyone who does not carry the Intelligent Key to push the request switch to lock/unlock the doors.

SPA2407

DOOR LOCKS/UNLOCKS PRECAU- TION . Do not push the door handle request switch with the Intelligent Key held in your hand as illustrated. The close distance to the door handle will cause the Intelligent Key system to have difficulty recognizing that the In- telligent Key is outside the vehicle.

. After locking with the door handle request switch, verify the doors are securely locked by testing them.

To prevent the Intelligent Key from being left inside the vehicle, make sure you carry the key with you and then lock the doors.

Black plate (139,1)

. Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open. Release the door handle once and pull it again to open the door.

The Intelligent Key system (opening/closing doors with the door handle request switch) can be set to remain inactive. (See “VEHI- CLE INFORMATION AND SETTINGS” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition sys- tems” section.)

Pre-driving checks and adjustments 3-9

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (140,1)

When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch *A the lift gate request switch *B within the range of opera- tion.

or

When you lock or unlock the doors or the lift gate, the hazard indicator will flash and the horn (or the outside chime) will sound as a confirma- tion. For details, see “Setting hazard indicator and horn mode” later in this section.

Locking doors 1. Move the selector

lever

to the P (Park) position, push the ignition switch to the OFF position and make sure you carry the Intelligent Key with you.*1

2. Close all the doors.*2
3. Push the door handle request switch *A or lift gate request switch *B while carrying the Intelligent Key with you.*3

4. All the doors and the lift gate will lock.

5. The hazard indicator flashes twice and the

outside chime sounds twice.

*1: Doors will lock with the Intelligent Key while the ignition switch is in the ACC or ON position.

SPA2435

*2: Doors will not lock with the Intelligent Key

while any door is open.

Model "Z51-D" EDITED: 2007/ 10/ 2

SPA2408

SPA2434

INTELLIGENT KEY OPERATION You can lock or unlock the doors without taking the key out from your pocket or bag.

3-10 Pre-driving checks and adjustments

*3: Doors will not lock by pushing the door handle request switch with the Intelligent Key inside the vehicle. However, when an Intelligent Key is inside the vehicle, doors can be locked with another registered Intelligent Key.

Unlocking doors 1. Push the door handle request switch *A or the lift gate request switch *B once while carrying the Intelligent Key with you.

2. The hazard indicator flashes once and the outside chime sounds once. The corre- sponding door or the lift gate will unlock.

3. Push the request switch again within 1

minute.

4. The hazard indicator flashes once and the outside chime sounds once again. All the doors and the lift gate will unlock.

All doors will be locked automatically unless one of the following operations is performed within 1
minute after pushing the request switch while the doors are locked. If during this 1-minute time period, the request switch is pushed, all doors will be locked automatically after another 1
minute. . Opening any door . Pushing the ignition switch

Power lift gate open (if so equipped) 1. Carry the Intelligent Key. 2. Push the power lift gate opener switch *C . 3. The lift gate will unlock and automatically

open.

4. The hazard indicator flashes 5 times and the

outside chime sounds.

To close the lift gate, push the power lift gate button on the key, or power lift gate switch on the instrument panel or lower part of the lift gate. (See “LIFT GATE” in the “3. Pre-driving checks and adjustments” section.)

Setting hazard indicator and horn mode This vehicle is set in hazard indicator and horn mode when you first receive the vehicle.

button *1

In hazard indicator and horn mode, when the LOCK is pushed, the hazard indicator flashes twice and the horn chirps once. button *2
When the UNLOCK is pushed, the hazard indicator flashes once.

If horns are not necessary, the system can be switched to the hazard indicator mode.

In hazard indicator mode, when the LOCK button is pushed, the hazard indicator flashes twice. When the UNLOCK button is pushed, neither the hazard indicator nor the horn operates.

Black plate (141,1)

Pre-driving checks and adjustments 3-11

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (142,1)

Hazard indicator and horn mode:

Intelligent Key system

(Using door handle or lift gate request switch)

Remote keyless entry system

(Using

or

button)

DOOR LOCK

DOOR UNLOCK

HAZARD - twice OUTSIDE CHIME - twice

HAZARD - once OUTSIDE CHIME - once

HAZARD - twice HORN - once

HAZARD - once HORN - none

Hazard indicator mode:

Intelligent Key system

(Using door handle or lift gate request switch)

Remote keyless entry system

(Using

or

button)

DOOR LOCK

DOOR UNLOCK

HAZARD - twice

HAZARD - none

HAZARD - twice

HAZARD - none

Switching procedure: Push the LOCK *1 and UNLOCK *2
buttons simultaneously for more than 2 seconds to switch the mode from one to the other.

When pushing the buttons to set the hazard indicator mode, the hazard indicator flashes 3
times.

When pushing the buttons to set the hazard indicator and horn mode, the hazard indicator flashes once and the horn chirps once.

3-12 Pre-driving checks and adjustments

Model "Z51-D" EDITED: 2007/ 10/ 2

BATTERY SAVER SYSTEM When all the following conditions are met for 60
minutes, the battery saver system will cut off the power supply to prevent battery discharge.

The ignition switch is in the ACC position, and

. All doors are closed, and

The selector lever is in the P (Park) position.

WARNING SIGNALS the vehicle from moving To help prevent unexpectedly by erroneous operation of the Intelligent Key listed on the following chart or to help prevent the vehicle from being stolen, chime or beep sounds inside and outside the vehicle and a warning displays in the dot matrix liquid crystal display.

When a chime or beep sounds or the warning displays, be sure to check the vehicle and Intelligent Key.

See “TROUBLESHOOTING GUIDE” later in this section and “DOT MATRIX LIQUID CRYS- TAL DISPLAY” in the “2. Instruments and controls” section.

Black plate (143,1)

Pre-driving checks and adjustments 3-13

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (144,1)

TROUBLESHOOTING GUIDE

Symptom

Possible cause

Action to take

When pushing the ignition switch to stop the engine

The SHIFT P warning appears on the display and the inside warning chime sounds con- tinuously.

When opening the driver’s door to get out of the vehicle

The inside warning chime sounds continuously.

When closing the door after get- ting out of the vehicle

The NO KEY warning appears on the display, the outside chime sounds 3 times and the inside warning chime sounds for approximately 3 seconds.

The SHIFT P warning appears on the display and the outside chime sounds continuously.

The selector lever is not in the P (Park) position.

Shift the selector lever to the P (Park) position.

The ignition switch is in the ACC position.

Push the ignition switch to the OFF posi- tion.

The Intelligent Key is in the key port.

Remove the Intelligent Key from the key port.

The ignition switch is in the ACC or ON position.

Push the ignition switch to the OFF posi- tion.

The ignition switch is in the ACC or OFF position and the selector lever is not in the P (Park) position.

Move the selector lever to the P (Park) position and push the ignition switch to the OFF position.

When closing the door with the inside lock knob turned to LOCK

The outside chime sounds for approximately 3
seconds and all the doors unlock.

The Intelligent Key is inside the vehicle. Carry the Intelligent Key with you.

When pushing the door handle request switch to lock the door

The outside chime sounds for approximately 2
seconds.

The Intelligent Key is inside the vehicle. Carry the Intelligent Key with you.

A door is not closed securely.

Close the door securely.

The door handle request switch is pushed before the door is closed.

Push the door handle request switch after the door is closed.

3-14 Pre-driving checks and adjustments

Model "Z51-D" EDITED: 2007/ 10/ 2

REMOTE KEYLESS ENTRY SYSTEM

It is possible to lock/unlock all doors, activate the panic alarm and open the windows and lift gate (if so equipped) by pushing the buttons on the key from outside the vehicle.

Before locking the doors, make sure the key is not left in the vehicle.

The LOCK/UNLOCK button on the key can operate at a distance of approximately 33 ft (10
m) (The effective distance depends upon the conditions around the vehi- cle.)

from the vehicle.

The lock and unlock buttons will not operate when:

the distance between the key and the vehicle is over 33 ft (10 m).

the key battery is completely discharged.

After locking with the remote keyless entry function, pull the door handle to make sure the doors are securely locked.

The LOCK/UNLOCK operating range varies depending on the environment. To securely operate the lock and unlock buttons, approach the vehicle to about 3 ft (1 m) from the door.

Type A

SPA2252A

Type B

SPA2436

Black plate (145,1)

(if so equipped)

*1 LOCK button *2 UNLOCK button *3 Power lift gate button *4 PANIC button HOW TO USE REMOTE KEYLESS ENTRY SYSTEM When you lock or unlock the doors or the lift gate, the hazard indicator will flash and the horn (or the outside chime) will sound as a confirma- tion. For details, see “Setting hazard indicator and horn mode” later in this section.

Locking doors 1. Move the selector

lever

to the P (Park) position and push the ignition switch to the OFF position. Make sure you carry the key with you.*1

2. Close all the doors and lift gate.*2
button *1 .

3. Push the LOCK

4. All the doors and the lift gate will lock.

5. The hazard indicator flashes twice and the

horn chirps once.

*1: Doors will lock while the ignition switch is in

the ACC or ON position.

*2: Doors will not lock while any door is open.

Pre-driving checks and adjustments 3-15

Model "Z51-D" EDITED: 2007/ 10/ 2

Unlocking doors 1. Push the UNLOCK

2. The hazard indicator

button *2 once. flashes once. The

driver’s door will unlock.

3. Push the UNLOCK

button again within

1 minute.

4. The hazard indicator flashes once again. All

the doors and the lift gate will unlock.

All doors will be locked automatically unless one of the following operations is performed within 1
minute after pushing the UNLOCK button while the doors are locked. If during this 1-minute time period, the UNLOCK button is pushed, all doors will be locked automatically after another 1
minute. . Opening any door . Pushing the ignition switch

Opening windows To open the windows, push the door UNLOCK for about 3 seconds after the

button *2
door is unlocked.

To stop opening, release the UNLOCK button.

Windows cannot be closed using the button on the key.

3-16 Pre-driving checks and adjustments

The door windows can be opened or closed by turning the mechanical key in a door lock. (See “DOORS” earlier in this section.)

Opening/closing lift gate (if so equipped) *3
1. Push the power lift gate button

for more than 1 second.

2. The lift gate will automatically open.

The hazard indicator flashes 5 times and the outside chime sounds for approximately 3
seconds.

To close the lift gate, push the power lift gate button

*3 .

The lift gate will automatically close.

*3

If the button is pushed while the lift gate is being opened or closed, the lift gate will reverse.

*3 cannot be The power lift gate button operated when the ignition switch is in the ON position.

Using panic alarm If you are near your vehicle and feel threatened, you can activate the alarm according to the following procedure to call attention. button *4

for more

1. Push the PANIC than 1 second.

Black plate (146,1)

2. The theft warning alarm will sound and the

headlights will flash for 25 seconds.

3. The panic alarm stops under either of the

It has run for 25 seconds, or

following conditions. . Any of the buttons is pushed. (Note: the panic button should be pushed for more than 1 second.)

Setting hazard indicator and horn mode This vehicle is set in hazard indicator and horn mode when you first receive the vehicle.

button *1

In hazard indicator and horn mode, when the LOCK is pushed, the hazard indicator flashes twice and the horn chirps once. button *2
When the UNLOCK is pushed, the hazard indicator flashes once.

If horns are not necessary, the system can be switched to the hazard indicator mode.

In hazard indicator mode, when the LOCK button is pushed, the hazard indicator flashes twice. When the UNLOCK button is pushed, neither the hazard indicator nor the horn operates.

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (147,1)

Hazard indicator and horn mode:

Intelligent Key system

(Using door handle or lift gate request switch)

Remote keyless entry system

(Using

or

button)

DOOR LOCK

DOOR UNLOCK

HAZARD - twice OUTSIDE CHIME - twice

HAZARD - once OUTSIDE CHIME - once

HAZARD - twice HORN - once

HAZARD - once HORN - none

Hazard indicator mode:

Intelligent Key system

(Using door handle or lift gate request switch)

Remote keyless entry system

(Using

or

button)

DOOR LOCK

DOOR UNLOCK

HAZARD - twice

HAZARD - none

HAZARD - twice

HAZARD - none

Switching procedure: Push the LOCK *1 and UNLOCK *2
buttons simultaneously for more than 2 seconds to switch the mode from one to the other.

When pushing the buttons to set the hazard indicator mode, the hazard indicator flashes 3
times.

When pushing the buttons to set the hazard indicator and horn mode, the hazard indicator flashes once and the horn chirps once.

Pre-driving checks and adjustments 3-17

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (148,1)

HOOD

LIFT GATE

SPA2437

WARNING

. Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident.

If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.