2009 Nissan Murano Owners Manual

As with any vehicle, a loss of control could result in a collision with other vehicles or objects, or cause the vehicle to rollover, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “SEAT BELTS” in the “1. Safety — Seats, seat belts and supplemental restraint system” section of this manual, and also instruct your passengers to do so.

Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted or improperly belted person is

Black plate (317,1)

significantly more likely to be injured or killed than a person properly wearing a seat belt.

ON-PAVEMENT AND OFF-ROAD DRIVING PRECAUTIONS Utility vehicles have a significantly higher rollover rate than other types of vehicles.

They have higher ground clearance than pas- senger cars to make them capable of performing in a variety of on-pavement and off-road applications. This gives them a higher center of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers, particularly at high speeds. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted or improperly belted person is significantly more likely to be injured or killed than a person properly wearing a seat belt.

Be sure to read “DRIVING SAFETY PRECAU- TIONS” later in this section.

Starting and driving 5-5

Model "Z51-D" EDITED: 2007/ 10/ 2

DRINKING ALCOHOL/DRUGS AND DRIVING

WARNING

Never drive under the influence of alcohol or drugs. Alcohol in the blood- stream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the se- verity of the injury.

NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Although the local is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol.

laws vary on what

is true for drugs,

Remember, drinking and driving don’t mix! And that too (over-the-counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.

5-6 Starting and driving

DRIVING SAFETY PRECAUTIONS Your NISSAN is designed for both normal and off-road use. However, avoid driving in deep water or mud as your NISSAN is mainly designed for leisure use, unlike a conventional off-road vehicle.

Remember that Two-Wheel Drive (2WD) mod- els are less capable than All-Wheel Drive (AWD) models for rough road driving and extrication when stuck in deep snow, mud, or the like.

Please observe the following precautions:

WARNING

. Drive carefully when off the road and avoid dangerous areas. Every person who drives or rides in this vehicle should be seated with their seat belt fastened. This will keep you and your passengers in position when driving over rough terrain.

. Do not drive across steep slopes. Instead drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward.

. Many hills are too steep for any

Black plate (318,1)

vehicle. If you drive up them, you may stall. If you drive down them, you may not be able to control your speed. If you drive across them, you may roll over.

. Do not shift ranges while driving on downhill grades as this could cause loss of control of the vehicle.

. Stay alert when driving to the top of a hill. At the top there could be a drop-off or other hazard that could cause an accident.

If your engine stalls or you cannot make it to the top of a steep hill, never attempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) range. Never back down in N (Neu- tral), using only the brake, as this could cause loss of control.

. Heavy braking going down a hill could cause your brakes to overheat and fade, resulting in loss of control and an accident. Apply brakes lightly and use a low range to control your speed.

. Unsecured cargo can be thrown around when driving over rough

Model "Z51-D" EDITED: 2007/ 10/ 2

.

terrain. Properly secure all cargo so it will not be thrown forward and cause injury to you or your passen- gers.

To avoid raising the center of gravity excessively, do not exceed the rated capacity of the roof rack (if so equipped) and evenly distribute the load. Secure heavy loads in the cargo area as far forward and as low as possible. Do not equip the vehicle with tires larger than speci- fied in this manual. This could cause your vehicle to roll over.

. Do not grip the inside or spokes of the steering wheel when driving off- road. The steering wheel could move suddenly and injure your hands. Instead drive with your fin- gers and thumbs on the outside of the rim.

. Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened.

. Always drive with the floor mats in place as the floor may became hot.

Lower your speed when encounter- ing strong crosswinds. With a higher

center of gravity, your NISSAN is more affected by strong side winds. Slower speeds ensure better vehicle control.

. Do not drive beyond the perfor- mance capability of the tires, even with AWD engaged.

. For AWD equipped vehicles, do not attempt to raise two wheels off the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or un- expected vehicle movement which could result in serious vehicle da- mage or personal injury.

. Do not attempt to test an AWD equipped vehicle on a 2-wheel dy- namometer (such as the dynam- ometers used by some states for emissions testing), or similar equip- ment even if the other two wheels are raised off the ground. Make sure you inform test facility personnel that your vehicle is equipped with AWD before it is placed on a dynamometer. Using the wrong test equipment may result in drivetrain damage or unexpected vehicle

Black plate (319,1)

movement which could result in serious vehicle damage or personal injury. (AWD models)

. When a wheel is off the ground due to an unlevel surface, do not spin the wheel excessively.

. Accelerating quickly, sharp steering maneuvers or sudden braking may cause loss of control.

If at all possible, avoid sharp turning maneuvers, particularly at high speeds. Your vehicle has a higher center of gravity than a conventional passenger car. The vehicle is not designed for cornering at the same speeds as conventional passenger cars. Failure to operate this vehicle correctly could result in loss of control and/or a rollover accident.

. Always use tires of the same type, size, brand, construction (bias, bias- belted or radial), and tread pattern on all four wheels. Install tire chains on the front wheels when driving on slippery roads and drive carefully.

. Be sure to check the brakes imme- diately after driving in mud or water. See “BRAKE SYSTEM” later in this

Starting and driving 5-7

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (320,1)

PUSH-BUTTON IGNITION SWITCH

WARNING

Do not operate the push-button ignition switch while driving the vehicle except in an emergency. (The engine will stop when the ignition switch is pushed 3
consecutive times or the ignition switch is pushed and held for more than 2
seconds.) If the engine stops while the vehicle is being driven, this could lead to a crash and serious injury.

SSD0689

Without Intelligent Key system

Before operating the push-button ignition switch, be sure to move the selector lever to the P (Park) position. Be sure to insert the key into the key port *1 . (Except for the Intelligent Key system equipped model)

INTELLIGENT KEY SYSTEM (if so equipped) The Intelligent Key system can operate the ignition switch without taking the key out from your pocket or purse. The operating environment and/or conditions may affect the Intelligent Key system operation.

Model "Z51-D" EDITED: 2007/ 10/ 2

section for wet brakes.

. Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or sideways, you could be injured.

. Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. See the maintenance information in the “NISSAN Service and Maintenance Guide”.

. Spinning the front wheels on slip- pery surfaces may cause the AWD warning light to flash and the AWD system to automatically switch from the AWD mode to the 2WD mode. This could reduce traction. Be espe- cially careful when towing a trailer. (AWD models)

5-8 Starting and driving

CAUTION

. Be sure to carry the Intelligent Key with you when operating the vehi- cle.

. Never leave the Intelligent Key in- side the vehicle when you leave the vehicle.

Black plate (321,1)

The cargo area is not included in the operating range, but the Intelligent Key may function.

the Intelligent Key is placed on the inside the glove box or the Intelligent Key may not

If instrument panel, door pocket, function.

If the Intelligent Key is placed near the door or window outside the vehicle, the Intelligent Key may function.

Starting and driving 5-9

Model "Z51-D" EDITED: 2007/ 10/ 2

SSD0436

Operating range The Intelligent Key functions can only be used for starting the engine when the Intelligent Key is within the specified operating range *1 . When the Intelligent Key battery is almost discharged or strong radio waves are present near the operating location, the Intelligent Key system’s operating range becomes narrower and may not function properly.

If the Intelligent Key is within the operating range, it is possible for anyone, even someone who does not carry the Intelligent Key, to turn the ignition switch to start the engine.

Black plate (322,1)

The ignition switch is equipped with an anti-theft steering lock device.

The ignition lock is designed so that the ignition switch position cannot be switched to LOCK until the selector lever is moved to the P (Park) position.

When the ignition switch cannot be pushed toward the LOCK position, proceed as follows:

1. Move the selector lever into the P (Park)

position.

2. Push the ignition switch to the OFF position.

3. Open the door. The ignition switch will

change to the LOCK position.

The selector lever can be moved from the P (Park) position if the ignition switch is in the ON position and the brake pedal is depressed.

In order for the steering wheel to be locked, it must be turned about 1/8 of a right or left turn from the straight up position.

To lock the steering wheel, push the ignition switch to the OFF position. To unlock the steering wheel, push the igni- tion switch. If the steering lock release malfunction indicator appears on the dot matrix liquid crystal display, push the push-button ignition switch again while

lightly turning the steering wheel right and left. (See “DOT MATRIX LIQUID CRYSTAL DISPLAY” in the “2. Instruments and con- trols” section.)

If the battery of the vehicle is discharged, the push-button ignition switch cannot be turned from the LOCK position.

Some indicators and warnings for operation are displayed on the dot matrix liquid crystal display between the speedometer and tachometer. (See “DOT MATRIX LIQUID CRYSTAL DISPLAY” in the “2. Instruments and controls” section.)

PUSH-BUTTON IGNITION SWITCH POSITIONS LOCK (Normal parking position) The ignition switch can only be locked in this position.

The ignition switch will be unlocked when it is pushed to the ACC position while carrying the Intelligent Key or with the key inserted in the port.

ACC (Accessories) This position activates electrical accessories such as the radio, when the engine is not running.

Model "Z51-D" EDITED: 2007/ 10/ 2

SSD0688

PUSH-BUTTON IGNITION SWITCH OPERATION When the ignition switch is pushed without depressing the brake pedal, the ignition switch position will change as follows: . Push center once to change to ACC. . Push center two times to change to ON. . Push center three times to change to OFF.

(No position illuminates.)

. Push center four times to return to ACC. . Open or close any door to return to LOCK

during the OFF position.

5-10 Starting and driving

ON (Normal operating position) This position turns on the ignition system and electrical accessories.

OFF The engine can be turned off without locking the steering wheel.

The ignition lock is designed so that the ignition switch cannot be switched to the LOCK position until the selector lever is moved to the P (Park) position.

CAUTION

Do not leave the vehicle with the push- button ignition switch in ACC or ON positions when the engine is not run- ning for an extended period. This can discharge the battery.

SSD0690

KEY PORT Models without Intelligent Key system Be sure to insert the key into the key port *1
before pushing the ignition switch. Make sure the key ring side faces backward as that illustrated. it is latched and secured.

Insert the key in the port until

To remove the key from the port, push the ignition switch to the OFF position and pull the key out of the port.

While the door is opened, and for 15 seconds after the door is closed, the guide light *B of the key port *A illuminates. If the ignition switch is pushed without the key in

Black plate (323,1)

the key port, the guide light will blink.

Battery discharge:

If the battery of the key is almost discharged, the guide light *B of the key port *A blinks and the indicator appears on the dot matrix liquid crystal display. (See “DOT MATRIX LIQUID CRYSTAL DISPLAY” in the “2. Instruments and controls” section.)

To replace the battery, see “BATTERY REPLA- CEMENT” in the “8. Maintenance and do-it- yourself” section.

Models with Intelligent Key system

Intelligent Key battery discharge:

If the battery of the Intelligent Key is almost discharged, the guide light *B of the key port *A blinks and the indicator appears on the dot matrix liquid crystal display. (See “DOT MATRIX LIQUID CRYSTAL DISPLAY” in the “2. Instru- ments and controls” section.)

In this case, inserting the Intelligent Key into the port *1
allows you to start the engine. Make sure that the key ring side faces backward as illustrated. Insert the Intelligent Key in the port until it is latched and secured.

To remove the Intelligent Key from the port, push the ignition switch to the OFF position and pull the Intelligent Key out of the port.

Starting and driving 5-11

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (324,1)

BEFORE STARTING THE ENGINE

STARTING THE ENGINE

. Make sure the area around the vehicle is

1. Apply the parking brake.

clear.

. Check fluid levels such as engine oil, cool- ant, brake fluid and window washer fluid as frequently as possible, or at least whenever you refuel.

. Check that all windows and lights are clean. . Visually inspect tires for their appearance and condition. Also check tires for proper inflation.

Lock all doors.

. Position seat and adjust head restraints. . Adjust inside and outside mirrors.

Fasten seat belts and ask all passengers to do likewise.

. Check the operation of warning lights when the ignition switch is pushed to the ON position. (See “WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS” in the “2. Instruments and controls” section.)

2. Move the selector lever to the P (Park) or N

(Neutral) position. (P is recommended.)

The starter is designed not to operate unless the selector lever is in either of the above positions.

3.

Insert the key into the key port. (Without the Intelligent Key System)

Push the ignition switch to the ON position. Depress the brake pedal and push the ignition switch to start the engine.

To start the engine immediately, push and release the ignition switch while depressing the brake pedal with the ignition switch in any position.

the engine is very hard to start

If in extremely cold weather or when restart- ing, depress the accelerator pedal a little (approximately 1/3 to the floor) and while holding, crank the engine. Release the accelerator pedal when the engine starts.

the engine is very hard to start If because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Push the ignition switch to the ON position to start cranking the engine. After 5 or 6 seconds, stop

Model "Z51-D" EDITED: 2007/ 10/ 2

NOTE: The key port does not charge the key battery. If you see the low battery indicator in the dot matrix liquid crystal display, replace the battery as soon as possible. (See “BATTERY REPLACEMENT” in the “8. Maintenance and do-it-yourself” section.)

CAUTION

. Never place anything except the key in the key port. Doing so may cause damage to the equipment.

. Make sure the key is in the correct direction when inserting it to the key port. The engine may not start if it is in the incorrect direction.

. Remove the key from the key port after the ignition switch is pushed to the OFF position.

5-12 Starting and driving

5. To stop the engine, shift the selector lever to the P (Park) position and push the ignition switch to the OFF position.

cranking by pushing the ignition switch to OFF. After cranking the engine, release the accelerator pedal. Crank the engine with your foot off the accelerator pedal by depressing the brake pedal and pushing the push- button ignition switch to start the engine. If fails to run, repeat the above procedure.

the engine starts, but

CAUTION

Do not operate the starter for more than 15 seconds at a time. If the engine does not start, push the ignition switch to OFF and wait 10 seconds before cranking again, otherwise the starter could be damaged.

4. Warm-up

least 30
Allow the engine to idle for at seconds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather. In cold weather, keep the engine running for a minimum of 2 - 3 minutes before shutting it off. Starting and stopping the engine over a short period of time may make the vehicle more difficult to start.

Black plate (325,1)

DRIVING THE VEHICLE

CONTINUOUSLY VARIABLE TRANS- MISSION (CVT) The Continuously Variable Transmission (CVT) in your vehicle is electronically controlled to produce maximum power and smooth operation.

The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment.

Engine power may be automatically re- duced to protect the CVT if the engine speed increases quickly when driving on slippery roads or while being tested on some dynamometers.

Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before moving the selector lever out of the P (Park) position.

This CVT is designed so that the foot brake pedal must be depressed before shifting from P (Park) to any driving position while the ignition switch is in the ON position.

The selector lever cannot be moved out of the P (Park) position and into any of the other positions if the ignition switch is pushed to the LOCK, OFF or ACC position.

Starting and driving 5-13

Model "Z51-D" EDITED: 2007/ 10/ 2

2. Keep the foot brake pedal depressed and move the selector lever to a driving position.

3. Release the parking brake and foot brake pedal, and then gradually start the vehicle in motion.

WARNING

. Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive) or L (Low) position. Always depress the brake pedal until shift- ing is completed. Failure to do so could cause you to lose control and have an accident.

. Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.

. Never shift to P (Park) or R (Re- verse) while vehicle is moving. Fail- ure to do so could cause you to lose control and have an accident.

5-14 Starting and driving

CAUTION

. When stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose.

. Do not downshift abruptly on slip- pery roads. This may cause a loss of control.

Black plate (326,1)

SSD0691

Shifting To move the selector lever,

Push the button *A while depressing the brake pedal. Push the button *A . Just move the selector lever.

After starting the engine, fully depress the brake pedal, push the selector lever button and move the selector lever from the P (Park) position to any of the desired shift positions.

Model "Z51-D" EDITED: 2007/ 10/ 2

WARNING

Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage.

CAUTION

Use the P (Park) or R (Reverse) position only when the vehicle is completely stopped.

P (Park):

Use this selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal must be depressed and the selector lever button pushed in to move the selec- tor lever from N (Neutral) or any drive position to P (Park). Apply the parking brake. When parking on a hill, apply the parking brake first, then move the selector lever to the P (Park) position.

R (Reverse):

Use this position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed and the selector lever button pushed in to move the selector lever from P (Park), N (Neutral) or any driving position to R (Reverse).

N (Neutral):

Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving.

D (Drive):

Use this position for all normal forward driving.

L (Low):

Use this position for maximum engine braking on steep downhill gradients/climbing steep slopes and whenever approaching sharp bends. Do not use the L position in any other circumstances.

Black plate (327,1)

SSD0692

Overdrive (O/D) OFF switch When the O/D OFF switch is pushed with the selector lever in the D (Drive) position, the indicator light in the instrument panel illuminates.

Use the overdrive off mode when you need improved engine braking.

To turn off the overdrive off mode, push the O/D OFF switch again. The indicator light will turn off.

Each time the engine is started, or when the selector lever is shifted to any position other than the D (Drive) position, the overdrive off mode will be automatically turned off.

Starting and driving 5-15

Model "Z51-D" EDITED: 2007/ 10/ 2

seconds. Then turn the switch back to the ON position. The vehicle should return to its normal operating condition. If it does not return to its normal operating condi- tion, have a NISSAN dealer check the transmission and repair if necessary.

WARNING

When the high fluid temperature pro- tection mode or fail-safe operation occurs, vehicle speed may be gradually reduced. The reduced speed may be lower than other traffic, which could increase the chance of a collision. Be especially careful when driving. If ne- cessary, pull to the side of the road at a safe place and allow the transmission to return to normal operation, or have it repaired if necessary.

Accelerator downshift — In D position — For passing or hill climbing, fully depress the accelerator pedal to the floor. This shifts the transmission down into a lower gear, depending on the vehicle speed.

High fluid temperature protection mode This transmission has a high fluid temperature protection mode. If the fluid temperature be- comes too high (for example, when climbing steep grades in high temperature with heavy loads, such as when towing a trailer), engine power and, under some conditions, vehicle speed will be decreased automatically to reduce the chance of transmission damage. Vehicle speed can be controlled with the accelerator pedal, but the engine and vehicle speed may be limited.

Fail-safe If the vehicle is driven under extreme conditions, such as excessive wheel spin- ning and subsequent hard braking, the fail-safe system may be activated. The MIL may illuminate to indicate the fail-safe mode is activated. (See “Malfunction In- dicator Light (MIL)” in the “2. Instruments and controls” section.) This will occur even if all electrical circuits are functioning properly. In this case, turn the ignition switch to the OFF position and wait for 10
5-16 Starting and driving

Black plate (328,1)

SSD0693

Shift lock release If the battery charge is low or discharged, the selector lever may not be moved from the P (Park) position even with the brake pedal depressed and the selector lever button pushed.

To move the selector lever, perform the following procedure:

1. Push the ignition switch to the OFF or LOCK

position.

2. Apply the parking brake.

3. Remove the shift

lock release cover *A

using a suitable tool.

4. Push down the shift lock release *B using a

Model "Z51-D" EDITED: 2007/ 10/ 2

PARKING BRAKE

WARNING

. Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident.

. Do not release the parking brake

from outside the vehicle.

. Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully engaged.

. Do not leave children unattended in a vehicle. They could release the parking brake and cause an acci- dent.

suitable tool.

5. Push the selector lever button *C and move the selector lever to the N (Neutral) position *D while holding down the shift lock release.

Push the ignition switch to the ON position to unlock the steering wheel. The vehicle may be moved to the desired location.

the battery is discharged completely,

If the steering wheel cannot be unlocked. Do not move the vehicle with the steering wheel locked.

Replace the removed shift lock release cover after the operation.

If the selector lever cannot be moved out of the P (Park) position, have a NISSAN dealer check the CVT system as soon as possible.

WARNING

If the selector lever cannot be moved from the P (Park) position while the engine is running and the brake pedal is depressed, the stop lights may not work. Malfunctioning stop lights could cause an accident injuring yourself and others.

Black plate (329,1)

SPA2331

To apply: Fully depress the parking brake pedal *1 . To release: 1. Firmly apply the foot brake *2 . 2. Depress the parking brake pedal *1

and

the parking brake will be released.

3. Before driving, be sure the brake warning

light goes out.

Starting and driving 5-17

Model "Z51-D" EDITED: 2007/ 10/ 2

CRUISE CONTROL

PRECAUTIONS ON CRUISE CON- TROL

If the cruise control system malfunctions, it will cancel automatically. The CRUISE in- dicator light on the meter panel will then blink to warn the driver.

If the engine coolant temperature becomes excessively high, the cruise control system will cancel automatically.

If the CRUISE indicator light blinks, turn the cruise control main switch off and have the system checked by a NISSAN dealer.

The CRUISE indicator light may blink when the cruise control main switch is turned ON while pushing the RESUME/ACCELERATE, SET/COAST or CANCEL switch. To prop- erly set the cruise control system, perform the following procedures.

WARNING

Do not use the cruise control when driving under the following conditions: . when it is not possible to keep the

vehicle at a set speed

in heavy traffic or in traffic that varies in speed

. on winding or hilly roads

5-18 Starting and driving

Black plate (330,1)

. on slippery roads (rain, snow, ice,

etc.)

in very windy areas

Doing so could cause a loss of vehicle control and result in an accident.

SSD0694

1. RESUME/ACCELERATE switch 2. SET/COAST switch 3. CANCEL switch 4. MAIN (ON·OFF) switch CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed between 25 to 89 MPH (40 to 144 km/h) without keeping your foot on the accelerator pedal.

To turn on the cruise control, push the MAIN switch on. The CRUISE indicator light will illuminate.

To set cruising speed, accelerate the vehicle to the desired speed, push the SET/COAST

Model "Z51-D" EDITED: 2007/ 10/ 2

switch and release it. Take your foot off the accelerator pedal. Your vehicle will maintain the set speed.

To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle will return to the previously set speed.

The vehicle may not maintain the set speed on winding or hilly roads. If this happens, drive without the cruise control.

To cancel the preset speed, use one of the following methods:

a) Push the CANCEL switch.

b) Tap the brake pedal.

c) Turn the MAIN switch off. The CRUISE lights

will turn off.

If you depress the brake pedal while pushing the RESUME/ACCELERATE or SET/ COAST switch and reset at the cruising speed, the cruise control will disengage. Turn the MAIN switch off once and then turn it on again.

The cruise control will automatically cancel if the vehicle slows more than 8 MPH (13
km/h) below the set speed.

If you move the selector lever to the N (Neutral) position, the cruise control will be

canceled.

To reset at a faster cruising speed, use one of the following methods: . Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the SET/COAST switch.

. Push and hold the RESUME/ACCELERATE switch. When the vehicle attains the desired speed, release the switch.

. Push, then quickly release the RESUME/ ACCELERATE switch. Each time you do this, the set speed will increase by about 1
MPH (1.6 km/h).

To reset at a slower cruising speed, use one of the following methods:

Lightly tap the brake pedal. When the vehicle attains the desired speed, push the SET/COAST switch and release it.

. Push and hold the SET/COAST switch. Release the switch when the vehicle slows down to the desired speed.

. Push, then quickly release the SET/COAST switch. Each time you do this, the set speed will decrease by about 1 MPH (1.6 km/h).

Black plate (331,1)

To resume the preset speed, push and release the RESUME/ACCELERATE switch. The vehicle will resume the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).

Starting and driving 5-19

Model "Z51-D" EDITED: 2007/ 10/ 2

BREAK-IN SCHEDULE

INCREASING FUEL ECONOMY

CAUTION

During the first 1,200 miles (2,000 km), follow these recommendations to ob- tain maximum engine performance and ensure the future reliability and econo- my of your new vehicle. Failure to follow these recommendations may result in shortened engine life and reduced engine performance.

. Avoid driving for long periods at constant speed, either fast or slow. Do not run the engine over 4,000 rpm.

. Do not accelerate at full throttle in any gear. . Avoid quick starts. . Avoid hard braking as much as possible. . Do not tow a trailer for the first 500 miles (800 km). Your engine, axle or other parts could be damaged.

5-20 Starting and driving

. Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position.

. Drive at moderate speeds on the highway. Driving at high speed lowers fuel economy. . Avoid unnecessary stopping and braking. Keep a safe distance behind other vehicles. . Select a gear range suitable to road condi-

tions.

. Avoid unnecessary engine idling. . Keep your engine tuned up.

Follow the recommended periodic mainte- nance schedule.

. Keep the tires inflated to the correct pressure. Low tire pressure increases tire wear and lowers fuel economy.

. Keep the wheels in correct alignment. Improper alignment increases tire wear and lowers fuel economy.

. Air conditioner operation lowers fuel econ- omy. Use the air conditioner only when necessary.

. When cruising at highway speeds, it is more economical to use the air conditioner and leave the windows closed to reduce drag.

Black plate (332,1)

. Use the recommended viscosity engine oil. (See “ENGINE OIL AND OIL FILTER RECOMMENDATION” in the “9. Technical and consumer information” section.)

Model "Z51-D" EDITED: 2007/ 10/ 2

ALL-WHEEL DRIVE (AWD) (if so equipped)

WARNING

. For AWD equipped vehicles, do not attempt to raise two wheels off the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or un- expected vehicle movement which could result in serious vehicle da- mage or personal injury.

. Do not attempt to test an AWD equipped vehicle on a 2-wheel dy- namometer (such as the dynam- ometers used by some states for emissions testing) or similar equip- ment even if the other two wheels are raised off the ground. Make sure that you inform the test facility personnel that your vehicle is equipped with AWD before it is placed on a dynamometer. Using the wrong test equipment may re- sult in drivetrain damage or unex- pected vehicle movement which could result in serious vehicle da- mage or personal injury.

SSD0418

ALL-WHEEL DRIVE (AWD) LOCK SWITCH OPERATIONS The AWD LOCK switch located on the lower side of the instrument panel. This switch is used to select the AUTO or LOCK mode depending on the driving conditions.

Each time you push the lower part of the switch *A , the AWD mode will switch: AUTO ? LOCK ? AUTO.

Black plate (333,1)

LOCK mode The AWD LOCK indicator illuminate.

light

will

AUTO mode The AWD LOCK indicator light will turn off.

AWD mode

Wheel driven

AWD LOCK indica- tor light

Use condi- tions

AUTO

Distribution of tor- que to the front and rear wheels changes automatically, de- pending on road conditions encoun- tered [100:0] ↔ [50:50]. This results in im- proved driving stabi- lity.*1

Turns off.

For driving on paved or slippery roads

LOCK All-wheel drive*2, *3

AWD LOCK

For driving on rough roads

*1: When the rotation difference between the front and rear wheels is large, the AWD mode may change from AUTO to LOCK for a while, however, this is not a malfunction.

Starting and driving 5-21

Model "Z51-D" EDITED: 2007/ 10/ 2

WARNING

. When driving straight, shift the AWD LOCK switch to AUTO. Do not oper- ate the AWD LOCK switch when making a turn or backing up.

. Do not operate the AWD LOCK switch with the front wheel spin- ning.

. Engine idling speed is high while warming up the engine. Be espe- cially careful when starting or driv- ing on slippery surfaces.

. When turning the vehicle in LOCK mode on paved roads, you may feel a braking effect. This is a normal condition of the AWD model.

*2: LOCK mode will change to AUTO mode automatically when the vehicle has been driven at a high speed. The AWD LOCK indicator light turns off.

*3: LOCK mode will automatically be cancelled when the ignition switch is turned to the OFF position.

If the AWD LOCK switch is operated while accelerating or decelerating, or if the ignition switch is turned off, you may feel a jolt. This is normal.

The oil temperature of power train parts will increase if the vehicle is continuously operated under conditions where the differ- ence in rotation between the front and rear wheels is large (wheel slip), such as when driving the vehicle on rough roads through sand, mud or freeing a stuck vehicle. In these cases, the AWD warning light blinks rapidly and the AWD mode changes to 2WD to protect the powertrain parts. If you stop driving with the engine idling and wait until the warning light stops blinking, the AWD returns to the AUTO mode.

5-22 Starting and driving

Black plate (334,1)

SSD0336B

AWD WARNING LIGHT The AWD warning light is located in the meter.

The AWD warning light illuminates when the ignition switch is pushed to the ON position. It turns off soon after the engine is started.

Model "Z51-D" EDITED: 2007/ 10/ 2

.

checked by a NISSAN dealer as soon as possible.

The powertrain may be damaged if you continue driving with the warn- ing light blinking rapidly.

. Never drive on dry hard surface roads in the LOCK mode, as this will overload the powertrain and may cause a serious malfunction.

If any malfunction occurs in the AWD system while the engine is running, the warning light will come on.

The warning light may blink rapidly (about twice per second) while trying to free a stuck vehicle due to high powertrain oil temperature. The driving mode may change to 2WD. AUTO mode may change to LOCK mode before the warning light blinks. If the warning light blinks rapidly during operation, stop the vehicle with the engine idling in a safe place immediately. Then if turns off after a while, you can continue driving.

the light

A large difference between the diameters of front and rear wheels will make the warning light blink slowly (about once per two seconds). Pull off the road in a safe area, and idle the engine. Check that all tire tire sizes are the same, pressure is correct and tires are not worn.

CAUTION

If the warning light remains on after the above operation, have your vehicle checked by a NISSAN dealer as soon as possible.

If the warning light comes on while driving there may be a malfunction in the AWD system. Reduce the vehicle speed and have your vehicle

Black plate (335,1)

Starting and driving 5-23

Model "Z51-D" EDITED: 2007/ 10/ 2

PARKING/PARKING ON HILLS

WARNING

. Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.

. Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park). Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident. Make sure the selector lever has been pushed as far forward as it can

5-24 Starting and driving

SSD0488

go and cannot be moved without depressing the foot brake pedal.

. Never leave the engine running

while the vehicle is unattended.

. Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.

1. Firmly apply the parking brake.

2. Move the selector

lever

to the P (Park)

position.

Black plate (336,1)

3. To help prevent the vehicle from rolling into traffic when parked on an incline, it is a good practice to turn the wheels as illustrated. . HEADED DOWNHILL WITH CURB: *1
Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb.

. HEADED UPHILL WITH CURB: *2

Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb.

. HEADED UPHILL OR DOWNHILL, NO

CURB: *3
Turn the wheels toward the side of the road so the vehicle will move away from the center of the road if it moves.

4. Push the ignition switch to the LOCK

position.

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (337,1)

POWER STEERING

BRAKE SYSTEM

WARNING

If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate.

The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering.

If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, espe- cially in sharp turns and at low speeds.

BRAKING PRECAUTIONS The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels.

Vacuum assisted brakes The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and the stopping distance will be longer.

Using the brakes Avoid resting your foot on the brake pedal while driving. This will cause overheating of the brakes, wearing out the brake and pads faster and reduce gas mileage.

To help reduce brake wear and to prevent the brakes from overheating, reduce speed and downshift to a lower gear before going down a slope or long grade. Overheated brakes may reduce braking performance and could result in loss of vehicle control.

WARNING

. While driving on a slippery surface, be careful when braking, accelerat- ing or downshifting. Abrupt braking

or accelerating could cause the wheels to skid and result in an accident.

If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder.

Wet brakes When the vehicle is washed or driven through water, the brakes may get wet. As a result, your braking distance will be longer and the vehicle may pull to one side during braking.

To dry brakes, drive the vehicle at a safe speed while lightly tapping the brake pedal to heat-up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly.

PARKING BRAKE BREAK-IN Break in the parking brake shoes whenever the stopping effect of the parking brake is weakened or whenever the parking brake shoes and/or drums/rotors are replaced, in order to assure the best braking performance.

This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer.

Starting and driving 5-25

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (338,1)

ANTI-LOCK BRAKING SYSTEM (ABS)

WARNING

The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces. Remember that stopping distances on slippery sur- faces will be longer than on normal surfaces even with ABS. Stopping distances may also be longer on rough, gravel or snow covered roads, or if you are using tire chains. Always maintain a safe distance from the vehicle in front of you. Ultimately, the driver is responsible for safety.

Tire type and condition may also affect braking effectiveness.

— When replacing tires, install the specified size of tires on all four wheels.

— When installing a spare tire, make sure that it is the proper size and type as specified on the

5-26 Starting and driving

Tire and Loading Information label. See “TIRE AND LOADING INFORMATION LABEL” in the “9. Technical and consumer infor- mation” section of this manual. — For detailed information, see “WHEELS AND TIRES” in the “8. Maintenance and do-it-your- self” section of this manual.

The Anti-lock Braking System (ABS) controls the brakes so the wheels do not lock during hard braking or when braking on slippery surfaces. The system detects the rotation speed at each wheel and varies the brake fluid pressure to prevent each wheel from locking and sliding. By preventing each wheel from locking, the system helps the driver maintain steering control and helps to minimize swerving and spinning on slippery surfaces.

Using the system Depress the brake pedal and hold it down. Depress the brake pedal with firm steady pressure, but do not pump the brakes. The ABS will operate to prevent the wheels from locking up. Steer the vehicle to avoid obstacles.

WARNING

Do not pump the brake pedal. Doing so

may result in increased stopping dis- tances.

Self-test feature The ABS includes electronic sensors, electric pumps, hydraulic solenoids and a computer. The computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse. When the self-test occurs, you may hear a “clunk” noise and/or feel a pulsation in the brake pedal. This is normal and does not indicate a malfunction. If the computer senses a malfunction, it switches the ABS off and illuminates the ABS warning light on the instrument panel. The brake system then oper- ates normally, but without anti-lock assistance.

If the ABS warning light illuminates during the self-test or while driving, have the vehicle checked by a NISSAN dealer.

Normal operation The ABS operates at speeds above 3 to 6 MPH (5 to 10 km/h). The speed varies according to road conditions.

When the ABS senses that one or more wheels are close to locking up, the actuator rapidly applies and releases hydraulic pressure. This action is similar to pumping the brakes very quickly. You may feel a pulsation in the brake pedal and hear a noise from under the hood or

Model "Z51-D" EDITED: 2007/ 10/ 2

feel a vibration from the actuator when it is operating. This is normal and indicates that the ABS is operating properly. However, the pulsa- tion may indicate that road conditions are hazardous and extra care is required while driving.

VEHICLE DYNAMIC CONTROL (VDC) SYSTEM

When accelerating or driving on slippery sur- faces, the tires may spin or slide. With the Vehicle Dynamic Control (VDC) system, sensors detect these movements and control the braking and engine output to help improve vehicle stability. . When the VDC system is operating,

the in the instrument panel

“SLIP” indicator blinks.

the “SLIP” indicator blinks,

If the road conditions are slippery. Be sure to adjust your speed and driving to these conditions. Be sure to drive carefully. (See “Slip indicator light” in the “2. Instruments and controls” section, and “Vehicle Dynamic Control (VDC) off indicator light” in the “2. Instruments and controls” section.)

Indicator light

If a malfunction occurs in the system, the “SLIP” and “VDC OFF” indicator lights illuminate in the instrument panel. As long as these indicators are illuminated, the VDC system function is canceled.

The VDC system uses an Active Brake Limited Slip (ABLS) function to improve vehicle traction. The ABLS system works when one of the driving wheels is spinning on a slippery surface. The ABLS system brakes the spinning wheel, which distributes the driving power to the other drive

Black plate (339,1)

wheel. If the vehicle is operated with the VDC OFF switch pushed and the VDC system turned off, all VDC systems will be turned off. The ABLS system and ABS will still operate with the VDC system off. If the ABLS system is activated, the “SLIP” indicator will blink and you may hear a clunk noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction.

While the VDC system is operating, you may feel a pulsation in the brake pedal and hear a noise or feel a vibration from under the hood. This is normal and indicates that the VDC system is working properly.

The VDC system computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed forward or backward. When the self-test occurs, you may hear a “clunk” noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction.

WARNING

The VDC system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or due to careless or dangerous driv- ing techniques. Reduce vehicle

Starting and driving 5-27

Model "Z51-D" EDITED: 2007/ 10/ 2

. When driving on extremely inclined surfaces such as higher banked corners, the VDC system may not operate properly and the “VDC OFF” indicator or “SLIP” indicator or both indicator lights may illuminate. Do not drive on these types of roads.

. When driving on unstable surfaces such as a turntable, ferry, elevator or ramp, the “VDC OFF” indicator or “SLIP” indicator or both indicator lights may illuminate. This is not a malfunction. Restart the engine after driving onto a stable surface.

If wheels or tires other than those recommended are used, the VDC system may not operate properly and “VDC OFF” indicator or “SLIP” indicator or both indicator lights may illuminate.

The VDC system is not a substitute for winter tires or tire chains on a snow covered road.

speed and be especially careful when driving and cornering on slip- pery surfaces and always drive care- fully.

. Do not modify the vehicle’s suspen- sion. If suspension parts such as shock absorbers, struts, springs, stabilizer bars and bushings and wheels are not NISSAN approved or are extremely deteriorated the VDC system may not operate prop- erly. This could adversely affect vehicle handling performance, and the “VDC OFF” indicator or “SLIP” indicator or both indicator lights may illuminate.

If brake related parts such as brake pads, rotors and calipers are not standard equipment or are extre- mely deteriorated, the “VDC OFF” indicator or “SLIP” indicator or both indicator lights may illuminate.

If engine related parts such as muffler are not standard equipment or are extremely deteriorated, the “VDC OFF” indicator or “SLIP” in- dicator or both indicator lights may illuminate.

5-28 Starting and driving

Black plate (340,1)

COLD WEATHER DRIVING

FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply deicer through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole or use the remote keyless entry keyfob.

is anticipated that

ANTI-FREEZE In the winter when it the outside temperature will drop below 328F (08C), check the anti-freeze to assure proper winter protection. For additional information, see “EN- GINE COOLING SYSTEM” in the “8. Main- tenance and do-it-yourself” section.

the battery is not

BATTERY If fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maximum efficiency, the battery should be checked regularly. For additional information, see “BATTERY” in the “8. Maintenance and do- it-yourself” section.

DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti- freeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “ENGINE COOLING SYSTEM” in the “8. Maintenance and do-it-yourself” section.

Model "Z51-D" EDITED: 2007/ 10/ 2

the performance of

TIRE EQUIPMENT SUMMER tires have a tread designed to provide superior performance on dry pavement. How- ever, these tires will be substantially reduced in snowy and icy condi- tions. If you operate your vehicle on snowy or icy roads, NISSAN recommends the use of MUD & SNOW or ALL SEASON tires on all four wheels. Consult a NISSAN dealer for the tire type, size, speed rating and availability information.

For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires.

Skid and traction capabilities of studded snow tires, on wet or dry surfaces, may be poorer than that of non-studded snow tires.

Tire chains may be used. For details, see “TIRE CHAINS” in the “8. Maintenance and do-it- yourself” section of this manual.

All-Wheel Drive (AWD) model If you install snow tires, they must also be the same size, brand, construction and tread pattern on all four wheels.

SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: . A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades.

. A sturdy, flat board to be placed under the

jack to give it firm support.

. A shovel to dig the vehicle out of snow-

drifts.

. Extra window washer

fluid to refill

the

reservoir tank.

DRIVING ON SNOW OR ICE

WARNING

. Wet ice (328F, 08C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or “grip” under these conditions. Try to avoid driving on wet ice until the road is salted or sanded.

. Whatever the condition, drive with caution. Accelerate and slow down with care. If accelerating or down- shifting too fast, the drive wheels

Black plate (341,1)

will lose even more traction.

. Allow more stopping distance under these conditions. Braking should be started sooner than on dry pave- ment.

. Allow greater following distances

on slippery roads.

. Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reaching it. Try not to brake while on the ice, and avoid any sudden steering maneuvers.

. Do not use cruise control on slip-

pery roads.

. Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle.

ENGINE BLOCK HEATER (if so equipped) Engine block heaters are available through NISSAN dealers to assist in cold temperature starting. The engine block heater should be used when the outside temperature is 208F (−78C) or lower.

Starting and driving 5-29

Model "Z51-D" EDITED: 2007/ 10/ 2

starting the engine. Damage to the cord could result in an electrical shock and can cause serious injury. . Use a heavy-duty 3-wire, 3-pronged extension cord rated for at least 10A. Plug the extension cord into a Ground Fault Interrupt (GFI) pro- tected, grounded 110-VAC outlet. Failure to use the proper extension cord or a grounded outlet can result in a fire or electrical shock and cause serious personal injury.

To use the engine block heater 1. Turn the engine off.

2. Open the hood and unwrap the engine

block heater cord.

3. Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord.

4. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110- volt AC (VAC) outlet.

5. The engine block heater must be plugged in for at least 2 - 4 hours, depending on outside temperatures, to properly warm the engine coolant. Use an appropriate timer to turn the engine block heater on.

6. Before starting the engine, unplug and properly store the cord to keep it away from moving parts.

WARNING

. Do not use your engine block heater with an ungrounded electrical sys- tem or a 2-pronged adapter. You can be seriously injured by an electrical shock if you use an ungrounded connection.

. Disconnect and properly store the engine block heater cord before

5-30 Starting and driving

Black plate (342,1)

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (19,1)

6 In case of emergency

Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Tire Pressure Monitoring System (TPMS). . . . . . . . . . . . . 6-2
Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Push starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

If your vehicle overheats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Towing your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Towing recommended by NISSAN . . . . . . . . . . . . . . . . . . . 6-13
Vehicle recovery (freeing a stuck vehicle) . . . . . . . . . . . 6-15

Model "Z51-D" EDITED: 2007/ 10/ 2

FLAT TIRE

TIRE PRESSURE MONITORING SYS- TEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. If the vehicle is being driven with low tire pressure, the TPMS will activate and warn you of it by the low tire pressure warning light. This system will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). For more details, see “WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS” in the “2. Instruments and controls” section and “TIRE PRESSURE MONITORING SYSTEM (TPMS)” in the “5. Starting and driving” section.

WARNING

If the low tire pressure warning light illuminates while driving, avoid sud- den steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possi- ble. Driving with under-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage

6-2 In case of emergency

could occur and may lead to an accident and could result in serious personal injury. Check the tire pres- sure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possi- ble.

. When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.

. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS. . Do not

inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.

Black plate (346,1)

CHANGING A FLAT TIRE If you have a flat tire, below.

follow the instructions

Stopping the vehicle 1. Safely move the vehicle off the road and

away from traffic.

2. Turn on the hazard warning flashers.

3. Park on a level surface and apply the parking brake. Move the selector lever to the P (Park) position.

4. Turn off the engine.

5. Raise the hood to warn other traffic, and to signal professional road assistance person- nel that you need assistance.

6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle.

WARNING

. Make sure the parking brake is securely applied and the transmis- sion is shifted into the P (Park) position.

. Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.

Model "Z51-D" EDITED: 2007/ 10/ 2

. Never change tires if oncoming traffic is close to your vehicle. Wait for professional road assistance.

Black plate (347,1)

Getting the spare tire and tools 1. Open the lift gate.

2. Remove the cargo cover (if so equipped). Instru-

(See “CARGO COVER” in the “2. ments and controls” section.)

3. Open the cargo floor board.

(See “CARGO FLOOR BOX” in the “2. Instruments and controls” section.)

In case of emergency 6-3

Model "Z51-D" EDITED: 2007/ 10/ 2

MCE0001A

Blocking wheels Place suitable blocks *1 at both the front and back of the wheel diagonally opposite the flat tire to prevent the vehicle from moving when it is jacked up.

WARNING

Be sure to block the wheel as the vehicle may move and result in personal injury.

Black plate (348,1)

4. Type A:

Remove the cargo floor boards.

Type B:

Turn the clips counterclockwise and remove the cargo floor box.

Type A

SCE0728

5. Type B:

Type B

SCE0713

Remove the strap from the back side of the board *1 , and hang it on the opening of the lift gate *2 .

Type B and C

SCE0715

6-4 In case of emergency

Model "Z51-D" EDITED: 2007/ 10/ 2

Black plate (349,1)

6. Remove the jacking tools and the spare tire.

Spare tire: Turn the clamp to remove the tire.

Jacking tools

Spare tire

Removing wheel cover (if so equipped)

SCE0716

SCE0700

SCE0630

Jacking tools: Remove the jack by turning it, then remove the other tools.

WARNING