uThe passenger’s door unlocks.
2013 Accord Coupe
1Using the Remote Transmitter
If the distance at which it works varies, the battery is probably low.
If the LED does not come on when you press a button, the battery is dead.
2 Replacing the Button Battery P. 495
You can customize the door unlock mode setting.
2 Customized Features P. 273
QRG
TOC
Index
Home
90
uuLocking and Unlocking the DoorsuLocking/Unlocking the Doors from the Outside
2013 Accord Coupe
QRG
■ Using the Smart Entry with Push Button Start System*
When you carry the smart entry remote, you can lock/unlock the doors and open the trunk. You can lock/unlock the doors within a radius of about 32 inches (80 cm) of the outside door handle. You can open the trunk within about 32 inches (80 cm) radius from the trunk release button.
■ Locking the doors and the trunk
Door Lock Button
Press the door lock button on either door. uSome exterior lights flash; the beeper
sounds; both doors and the trunk lock; and the security system sets.
* Not available on all models
Continued
1Using the Smart Entry with Push Button Start System*
• Do not leave the smart entry remote in the vehicle
when you get out. Carry it with you.
• A person who is not carrying the smart entry
remote can lock/unlock the doors if a person who is carrying it is within range.
• The door may be unlocked if the door handle is
covered with water in heavy rain or in a car wash if the smart entry remote is within range.
• If you grip either door handle wearing gloves, the
door sensor may be slow to respond or may not respond by unlocking the doors.
• You cannot unlock the door by gripping the handle
after two seconds of locking it.
• The door might not open if you pull it immediately
after gripping the door handle. Grip the handle again and confirm that the door is unlocked before pulling the handle.
If the distance at which it works varies, the battery is probably low. If the LED does not come on when you press a button, the battery is dead.
2 Replacing the Button Battery P. 495
You can customize the door lock mode and keyless lock acknowledgement setting.
2 Customized Features P. 273
TOC
Index
Home
91
uuLocking and Unlocking the Doors uLocking/Unlocking the Doors from the Outside
■ Unlocking the doors and the trunk
Grab the driver’s door handle: uThe driver’s door unlocks. uSome exterior lights flash twice and the
beeper sounds twice.
Grab the passenger’s door handle:
uBoth doors and the trunk unlock. uSome exterior lights flash twice and the
beeper sounds twice.
Press the trunk release button:
uThe trunk unlocks and opens.
2 Using the Trunk Release Button* P. 98
Trunk Release Button
2013 Accord Coupe
1Using the Smart Entry with Push Button Start System*
• Even within the 32 inches (80 cm) radius, you may not be able to lock/unlock the doors with the smart entry remote if it is above or below the outside handle.
• The smart entry remote may not operate if it is too
close to the door and door glass.
If you do not open a door within 30 seconds of unlocking the vehicle, the doors will automatically relock.
The light flash, beep and unlock settings can be customized.
2 Customized Features P. 273
* Not available on all models
QRG
TOC
Index
Home
92
uuLocking and Unlocking the DoorsuLocking/Unlocking the Doors from the Outside
2013 Accord Coupe
QRG
1Locking/Unlocking the Doors Using a Key
When you lock the driver's door with a key, the passenger’s door locks at the same time. When unlocking, the driver's door unlocks first. Turn the key a second time within a few seconds to unlock the passenger’s door.
You can customize the door unlock mode setting.
2 Customized Features P. 273
1Locking a Door Without Using a Key
When you lock the driver's door, the passenger’s door locks at the same time.
Make sure you have the key in your hand before locking the door to prevent it from being locked in the vehicle.
■ Locking/Unlocking the Doors Using a Key
Fully insert the key and turn it.
Lock
Unlock
■ Locking a Door Without Using a Key
■ Locking the driver's door Push the lock tab forward a or push the master door lock switch in the lock direction b, and close the door.
■ Locking the passenger's door Push the lock tab forward and close the door.
■ Lockout prevention system The doors cannot be locked when the key is in the ignition switch*1, or the smart entry remote is inside the vehicle.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
TOC
Index
Home
93
uuLocking and Unlocking the Doors uLocking/Unlocking the Doors from the Inside
QRG
Locking/Unlocking the Doors from the Inside ■ Using the Lock Tab
■ Locking a door Push the lock tab forward.
■ Unlocking a door Pull the lock tab rearward.
To Lock
Lock Tab
To Unlock
TOC
2013 Accord Coupe
1Using the Lock Tab
When you lock the door using the lock tab on the driver's door, the passenger’s door locks at the same time. When you unlock the door using the lock tab on the driver's door, only the driver's door will unlock.
Index
Home
94
uuLocking and Unlocking the DoorsuLocking/Unlocking the Doors from the Inside
■ Unlocking Using the Inner Handle
Pull the inner handle.
uThe door unlocks and opens in one
motion.
2013 Accord Coupe
QRG
1Unlocking Using the Inner Handle
The inner handles are designed to allow front seat occupants to open the door in one motion. However this feature requires that front seat occupants never pull an inner handle while the vehicle is in motion.
Inner Handle
Unlocking and opening the driver’s door from the inner handle unlocks both doors.
To avoid both doors to be unlocked, use the lock tab on the driver’s door to unlock, then lock again before opening the door.
uThis setting works for one time only. If you do not want both doors to be
unlocked all the time, customize the Auto Door Unlock setting to Off using the audio/information screen.
Continued
TOC
Index
Home
95
uuLocking and Unlocking the Doors uAuto Door Locking/Unlocking
■ Using the Master Door Lock Switch
Press the master door lock switch in as shown to lock or unlock both doors.
To Lock
2013 Accord Coupe
1Using the Master Door Lock Switch
When you lock/unlock the driver's door using the master lock switch, the passenger’s door locks/ unlocks at the same time.
To Unlock
Master Door Lock Switch
Auto Door Locking/Unlocking Your vehicle locks and unlocks both doors automatically when a certain condition is met.
1Auto Door Locking/Unlocking
You can turn off or change to another auto door locking/unlocking setting using the audio/ information screen.
2 Customized Features P. 273
■ Auto Door Locking ■ Drive lock mode Both doors lock when the vehicle’s speed reaches about 10 mph (15 km/h).
■ Auto Door Unlocking ■ Driver’s door open mode Both doors unlock when the driver’s door is opened.
QRG
TOC
Index
Home
96
Opening and Closing the Trunk
Precautions for Opening/Closing the Trunk ■ Opening the trunk Open the trunk all the way.
u If it is not fully opened, the trunk lid may begin to close under its own weight.
■ Closing the trunk Keep the trunk lid closed while driving to:
uAvoid possible damage.
uPrevent exhaust gas from leaking into the vehicle.
2 Exhaust Gas Hazard P. 62
Using the Trunk Opener
Pulling the trunk release to the lower left of the driver's seat unlocks and opens the trunk.
Trunk Release
Continued
2013 Accord Coupe
QRG
TOC
Index
Home
97
uuOpening and Closing the TrunkuUsing the Trunk Release Button*
■ Locking the trunk opener You can lock the trunk release with the master key * or the built-in key *.
1Locking the trunk opener
Models without smart entry system If you need to give the key to someone else, give them the valet key.
2013 Accord Coupe
Using the Trunk Release Button*
Trunk Release Button
Press the release button on the trunk lid after the doors are unlocked.
Even if the trunk is locked, you can open the trunk if you carry the smart entry remote.
uThe beeper will sound.
1Using the Trunk Release Button*
• Do not leave the smart entry remote in the vehicle
when you get out. Carry it with you.
• A person who is not carrying the smart entry
remote can unlock the trunk if a person who is carrying it is within range.
• Do not leave the smart entry remote inside the
trunk and close the lid. The beeper sounds and the trunk cannot be closed.
• Do not carry the smart entry remote near the trunk
lid when closing it.
• Do not place the smart entry remote around the
rear seat when closing the trunk.
* Not available on all models
QRG
TOC
Index
Home
98
Using the Remote Transmitter
uuOpening and Closing the TrunkuUsing the Remote Transmitter
2013 Accord Coupe
QRG
Press the trunk release button for approximately one second to unlock and open the trunk.
Trunk Button
Trunk Main Switch*
Main Switch
ON
OFF
* Not available on all models
1Trunk Main Switch *
If you need to give the key to someone else, remove the built-in key from the smart entry remote by sliding the release knob, and give the remote as a valet key.
The trunk main switch disables the trunk release button on the remote transmitter and the trunk release button on the trunk lid to protect luggage in the trunk.
1. Make sure the rear seat-back is not folded
down.
2. Turn off the trunk main switch in the glove
box.
3. Lock the glove box.
4. Lock the trunk release.
2 Using the Trunk Opener P. 97
TOC
Index
Home
99
uuOpening and Closing the TrunkuEmergency Trunk Opener
Emergency Trunk Opener
QRG
The trunk release lever allows you to open the trunk from inside for your safety.
Slide the release lever in the direction of the arrow.
2013 Accord Coupe
1Emergency Trunk Opener
Parents should decide if their children should be shown how to use this feature.
Lever
TOC
Index
Home
100
Security System
Immobilizer System The immobilizer system prevents a key that has not been pre-registered from starting the engine. Each key contains electronic transmitters that use electronic signals to verify the key.
Pay attention to the following when inserting the key into the ignition switch or pressing the ENGINE START STOP button: • Do not allow objects that emit strong radio waves near the ignition switch or the
ENGINE START STOP button.
• Make sure the key is not covered by or touching a metal object.
• Do not bring a key from another vehicle's immobilizer system near the ignition
switch.
2013 Accord Coupe
QRG
1Immobilizer System
NOTICE Leaving the ignition key in the vehicle can result in theft or accidental movement of the vehicle.
Always take the ignition key with you whenever you leave the vehicle unattended.
Do not alter the system or add other devices to it. Doing so may damage the system and make your vehicle inoperable.
Security System Alarm The security system alarm activates when the doors, trunk, or hood are opened without the key, remote transmitter, or smart entry system.
1Security System Alarm
The security alarm continues for a maximum of two minutes until the security system deactivates.
■ When the security system alarm activates The horn sounds intermittently and all of the exterior lights flash.
■ To deactivate the security system alarm Unlock the vehicle using the key, remote transmitter or smart entry remote. The system, along with the horn and flashing lights, is deactivated.
Continued
TOC
Index
Home
101
uuSecurity SystemuSecurity System Alarm
■ Setting the security system alarm The security system alarm automatically sets when the following conditions have been met: • The ignition switch is in LOCK (0 *1, and the key has been removed from the
ignition switch.
• The hood and trunk are closed.
• Both doors are locked from outside with the key, the remote transmitter, or smart
entry system.
■ When the security system alarm sets The security system alarm indicator in the instrument panel blinks. When the blinking interval changes after about 15 seconds, the security system is set.
■ To cancel the security system alarm The security system alarm is canceled when the vehicle is unlocked using the key, remote transmitter, smart entry system or the ignition switch is turned to ON (w *1. The security system indicator goes off at the same time.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
2013 Accord Coupe
1Security System Alarm
Do not set the security system alarm when someone is in the vehicle or a window is open. The system can accidentally activate when: • Unlocking the door with the lock tab. • Opening the trunk with the trunk release or the
emergency trunk opener.
If the battery goes dead after you have set the security system alarm, the security alarm may go off once the battery is recharged or replaced.
If this occurs, deactivate the security system alarm by unlocking a door using the key or remote transmitter.
Do not attempt to alter this system or add another device to it.
QRG
TOC
Index
Home
102
■ Panic Mode
■ The panic button on the remote
transmitter
If you press the panic button for approximately one second, the following will occur for about 30 seconds: • The horn sounds.
• Some exterior lights flash.
Panic Button
■ Canceling panic mode Press any button on the remote transmitter, or turn the ignition switch to ON (w *1.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
uuSecurity SystemuSecurity System Alarm
2013 Accord Coupe
QRG
TOC
Index
Home
103
Opening and Closing the Windows
QRG
Opening/Closing the Power Windows The power windows can be opened and closed when the ignition switch is in ON (w *1, using the switches on the doors. The driver's side switches can be used to open and close both windows.
The power window lock button on the driver's side must be switched off (not pushed in, indicator off) to open and close the passenger’s window from the passenger's side.
TOC
When the power window lock button is pushed in, the indicator comes on and you can only operate the driver's window. Turn the power window lock button on when children are in the vehicle.
■ Opening/Closing Windows with Auto-Open/Close Function
On Off
Power Window Lock Button
■ Automatic operation To open: Push the switch down firmly.
To close: Pull the switch up firmly.
Driver’s Window Switch
Indicator
The window opens or closes completely. To stop the window at any time, push or pull the switch briefly.
Passenger’s Window Switch
■ Manual operation To open: Push the switch down lightly.
2013 Accord Coupe
1Opening/Closing the Power Windows
3WARNING
Closing a power window on someone's hands or fingers can cause serious injury.
Make sure your passengers are away from the windows before closing them.
The power windows can be operated for up to 10 minutes after you turn the ignition switch to LOCK (0 *1.
Opening either door cancels this function.
Auto Reverse If a power window senses resistance when closing automatically, it will stop closing and reverse direction.
The driver’s window auto reverse function is disabled when you continuously pull up the switch.
The auto reverse function stops sensing when the window is almost closed to ensure that it fully closes.
To close: Pull the switch up lightly. Release the switch when the window reaches the desired position.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
Index
Home
104
uuOpening and Closing the WindowsuOpening/Closing the Power Windows
2013 Accord Coupe
QRG
■ Opening/Closing Windows without Auto-Open/Close Function*
Close
Open
To open: Push the switch down.
To close: Pull the switch up.
Release the switch when the window reaches the desired position.
■ Opening Windows and Moonroof with the Remote*
To open: Press the unlock button twice within 10 seconds and hold it down for the second time. If the windows stop midway, repeat the procedure.
Unlock Button
* Not available on all models
Continued
TOC
Index
Home
105
uuOpening and Closing the WindowsuOpening/Closing the Power Windows
■ Opening/Closing the Windows and Moonroof with the Key* To open: Unlock the driver’s door with the key. Within 10 seconds of returning the key to the central position, turn the key in the unlock direction and hold it there.
Close
Open
To close: Lock the driver’s door with the key. Within 10 seconds of returning the key to the central position, turn the key in the lock direction and hold it there.
Release the key to stop the windows/ moonroof at the desired position. If you want further adjustment, repeat the same operation.
QRG
TOC
Index
Home
106
2013 Accord Coupe
* Not available on all models
Opening and Closing the Moonroof *
■ Opening/Closing the Moonroof You can only operate the moonroof when the ignition switch is in ON (w *1. Use the switch in the front of the ceiling to open and close the moonroof.
Open
Close
Tilt
■ Automatic operation To open: Pull the switch back firmly, then release.
To close: Push the switch forward firmly, then release.
The moonroof will automatically open or close all the way. To stop the moonroof midway, touch the switch briefly.
■ Manual operation To open: Pull the switch back, and hold it until the desired position is reached.
To close: Push the switch forward, and hold it until the desired position is reached.
■ Tilting the moonroof up To tilt: Push on the center of the moonroof switch.
To close: Push the switch forward firmly, then release.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
2013 Accord Coupe
QRG
1Opening/Closing the Moonroof
3WARNING
Opening or closing the moonroof on someone's hands or fingers can cause serious injury.
Make sure all hands and fingers are clear of the moonroof before opening or closing it.
NOTICE Opening the moonroof in below freezing temperature or when it is covered with snow or ice can damage the moonroof panel or motor.
The power moonroof can be operated for up to 10 minutes after you turn the ignition switch off. Opening either door cancels this function.
When resistance is detected, the auto reverse function causes the moonroof to change directions, then stop. Auto reverse stops sensing when the moonroof is almost closed to ensure that it fully closes. Make sure that all objects, including fingers, are clear of the moonroof.
TOC
Index
Home
107
Operating the Switches Around the Steering Wheel
Ignition Switch*
QRG
(0 LOCK: Insert and remove the key in this position.
(q ACCESSORY: Operate the audio system and other accessories in this position.
(w ON: This is the position when driving.
(e START: This position is for starting the engine. The switch returns to ON (w when you let go of the key.
TOC
Index
Home
108
2013 Accord Coupe
1Ignition Switch* Manual transmission models
3WARNING
Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.
Remove the key from the ignition switch only when parked.
Automatic transmission (CVT) models You cannot take the key out unless the shift lever is in (P.
All models If you open the driver's door when the key is in LOCK (0 or ACCESSORY (q, a warning buzzer will sound to remind you to take the key out.
If the key won't turn from LOCK (0 to ACCESSORY (q, turn the key while moving the steering wheel left and right. The steering wheel will unlock, allowing the key to turn.
* Not available on all models
ENGINE START/STOP Button* ■ Changing the Power Mode
Automatic Transmission
Indicator
VEHICLE OFF (LOCK) Indicator in the button is off. The steering wheel is locked. The power to all electrical components is turned off.
ACCESSORY Indicator in the button is on. Indicator in the button blinks (from ON to ACCESSORY). Operate the audio system and other accessories in this position.
ON Indicator in the button is on. All electrical components can be used.
Without pressing the brake pedal
Press the button without the shift lever in (P.
Press the button.
Shift to (P then press the button.
uuOperating the Switches Around the Steering WheeluENGINE START/STOP Button*
2013 Accord Coupe
QRG
Manual Transmission
Indicator
1ENGINE START/STOP Button *
ENGINE START/STOP Button Operating Range
Operating Range
You can start the engine when the smart entry remote is inside the vehicle. The engine may also run if the smart entry remote is close to the door or window, even if it is outside the vehicle.
ON mode: Indicator in the button is off, if the engine is running.
Without pressing the clutch pedal
If the smart entry remote battery is weak, the beeper sounds.
2 If the Smart Entry Remote Battery is Weak
P. 512
Do not leave the power mode in ACCESSORY or ON when you get out.
TOC
Index
Home
109
* Not available on all models
Continued
uuOperating the Switches Around the Steering WheeluENGINE START/STOP Button*
QRG
TOC
■ Automatic Power Off If you leave the vehicle for 30 to 60 minutes with the shift lever in (P *1 and the power mode in ACCESSORY, the vehicle automatically goes into the mode similar to VEHICLE OFF (LOCK) to avoid the battery drain.
When in this mode: The steering wheel does not lock.
You cannot lock or unlock doors with the remote transmitter or the smart entry system.
Press the ENGINE START/STOP button to switch the mode to VEHICLE OFF (LOCK).
2013 Accord Coupe
Index
Home
110
*1: Automatic transmission/CVT models
* Not available on all models
uuOperating the Switches Around the Steering WheeluENGINE START/STOP Button*
2013 Accord Coupe
QRG
■ Power Mode Reminder If you open the driver’s door when the power mode is set to ACCESSORY, a warning buzzer sounds.
■ Smart Entry Remote Reminder
Warning buzzers may sound from inside or/ and outside the vehicle to remind you that the smart entry remote is out of the vehicle. If the buzzer continues even after the remote is put back inside, place it to be within its operational range.
■ When the power mode is in ON If the smart entry remote is taken out of the vehicle, and the driver’s door is closed, warning buzzers sound from both inside and outside the vehicle. A warning message on the information display notifies the driver inside that the remote is out.
■ When the power mode is in
ACCESSORY
If the smart entry remote is taken out of the vehicle, and both doors are closed, a warning buzzer sounds from outside the vehicle.
* Not available on all models
1Smart Entry Remote Reminder
When the smart entry remote is within the system’s operational range, and the driver’s door is closed, the warning function cancels.
If the smart entry remote is taken out of the vehicle after the engine has been started, you can no longer change the ENGINE START/STOP button mode or restart the engine. Always make sure if the remote is in your vehicle when you operate the ENGINE START/STOP button.
Removing the smart entry remote from the vehicle through a window does not activate the warning buzzer.
Do not put the smart entry remote on the dashboard or in the glove box. It may cause the warning buzzer to go off. Under some other conditions that can prevent the vehicle from locating the remote, the warning buzzer may also go off even if the remote is within the system’s operational range.
TOC
Index
Home
111
uuOperating the Switches Around the Steering WheeluIgnition Switch and Power Mode Comparison
QRG
Ignition Switch and Power Mode Comparison
2013 Accord Coupe
Ignition Switch Position
LOCK (0) (with/without the key)
ACCESSORY (I)
ON (II)
START (III)
TOC
Without Smart Entry System
● Engine is turned off and
power is shut down. ● The steering wheel is
locked.
● No electrical
components can be used.
● Engine is turned off. ● Some electrical
components such as the audio system and the accessory power socket can be operated.
● Normal key position
● Use this position to start
while driving.
the engine.
● All electrical components
● The ignition switch
can be used.
returns to the ON (II) position when you release the key.
Power Mode
VEHICLE OFF (LOCK)
ACCESSORY
ON
START
With Smart Entry System and ENGINE START/ STOP Button
Indicator-Off ● Engine is turned off and
power is shut down. ● The steering wheel is
locked.
● No electrical
components can be used.
Indicator-On or blinking ● Engine is turned off. ● Some electrical
components such as the audio system and the accessory power socket can be operated.
Indicator is: On Off
Indicator- On (engine is turned off) Off (engine is running) ● All electrical components
Indicator-Off ● The mode automatically returns to ON after the engine starts.
can be used.
Index
Home
112
uuOperating the Switches Around the Steering WheeluTurn Signals
2013 Accord Coupe
QRG
Turn Signals
Right Turn
Left Turn
Light Switches ■ Manual Operation
High Beams
Flashing the high beams
Low Beams
Turns on parking, side marker, tail, and rear license plate lights Turns on headlights, parking, side marker, tail, and rear license plate lights
The turn signals can be used when the ignition switch is in ON (w *1. ■ One-touch turn signal When you lightly push up or down and release the turn signal lever, the exterior turn signals and turn signal indicator blink three times.
This feature can be used when signaling for a lane change.
Rotating the light switch turns the lights on and off, regardless of the position of the ignition switch*1. ■ High beams Push the lever forward until you hear a click. ■ Low beams When in high beams, pull the lever back to return to low beams. ■ Flashing the high beams Pull the lever back, and release it.
1Light Switches
If you remove the key from the ignition switch while the lights are on, a chime sounds when the driver’s door is opened.
When the lights are on, the lights on indicator in the instrument panel will be on.
2 Lights On Indicator P. 72
If you sense that the level of the headlights is abnormal, have the vehicle inspected by a dealer.
Do not leave the lights on when the engine is off because it will cause the battery to discharge.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
Continued
TOC
Index
Home
113
uuOperating the Switches Around the Steering WheeluLight Switches
■ Automatic Lighting Control
Automatic lighting control can be used when the ignition switch is in ON (w *1.
When you turn the light switch to AUTO, the headlights and other exterior lights will switch on and off automatically depending on the ambient brightness.
uYou can change the auto light sensitivity
setting.
2 Customized Features P. 273
2013 Accord Coupe
1Automatic Lighting Control
We recommend that you turn on the lights manually when driving at night, in a dense fog, or in dark areas such as long tunnels or parking facilities.
The light sensor is in the location shown below. Do not cover this light sensor with anything; otherwise, the automatic lighting system may not work properly.
Light Sensor
Adjust the auto light sensitivity as follows:
Setting
MAX HIGH MID LOW MIN
The exterior lights come on when the ambient light is at
Bright
Dark
QRG
TOC
Index
Home
114
uuOperating the Switches Around the Steering WheeluFog Lights*
2013 Accord Coupe
QRG
■ Headlight Integration with Wiper* The headlights automatically come on when the wipers are used several times within a certain number of intervals with the headlight switch in AUTO. The headlights automatically go off a few minutes later if the wipers are stopped. ■ Automatic Lighting Off Feature The headlights, all other exterior lights, and the instrument panel lights turn off within 15 seconds after you remove the key*1 and close the driver's door.
uYou can change the headlight auto off timer setting.
2 Customized Features P. 273
If you turn the ignition switch to LOCK (0 *1 with the headlight switch on, but do not open the door, the lights turn off after 10 minutes (three minutes, if the switch is in the AUTO position).
The lights turn on again when you unlock or open the driver's door. If you unlock the door, but do not open it within 15 seconds, the lights go off. If you open the driver's door, you will hear a lights on reminder chime.
Fog Lights*
When the low beam headlights are on, turn the fog light switch on to use the fog lights.
Fog Light Switch
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
1Headlight Integration with Wiper *
This feature activates while the headlights are off in AUTO.
The instrument panel brightness does not change when the headlights come on.
At dark ambient light levels, the automatic lighting control feature turns on the headlights, regardless of the number of wiper sweeps.
1Fog Lights *
When the fog lights are on, the indicator in the instrument panel will be on.
They go off when the headlights turn off, or when
the daytime running lights are on.
2 Fog Light Indicator * P. 72
TOC
Index
Home
115
uuOperating the Switches Around the Steering WheeluDaytime Running Lights
QRG
Daytime Running Lights Models with bulb type parking lights The high beam headlights come on slightly dimmer than normal when the following conditions have been met:
Models with LED type parking/daytime running lights The parking/daytime running lights come on when the following conditions have been met:
2013 Accord Coupe
TOC
Models with LED low beam headlights • The power mode is ON.
• The headlight switch is off, or in
• The parking brake is released.
Models with halogen low beam headlights • The ignition switch is in ON (w *1.
• The headlight switch is off.
• The parking brake is released.
The lights remain on even if you set the parking brake. Turning off the ignition switch or setting the power mode to VEHICLE OFF will turn off the daytime running lights.
Models with bulb type parking lights The high beam headlights return to the original brightness once the headlight switch is turned on.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
Index
Home
116
Wipers and Washers
2013 Accord Coupe
QRG
uuOperating the Switches Around the Steering WheeluWipers and Washers
Pull to use washer.
Intermittent Time Adjustment Ring
MIST OFF INT: Low speed with intermittent LO: Low speed wipe HI: High speed wipe
The windshield wipers and washers can be used when the ignition switch is in ON (w *1.
■ MIST The wipers run at high speed until you release the lever.
■ Wiper switch (OFF, INT, LO, HI) Change the wiper switch setting according to the amount of rain.
■ Adjusting the delay Turn the adjustment ring to adjust the wiper delay.
Long delay
Short delay
■ Washer Sprays while you pull the lever toward you. When you release the lever, the wipers make two or three more sweeps before stopping.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
1Wipers and Washers
NOTICE Do not use the wipers when the windshield is dry. The windshield will get scratched, or the rubber blades will get damaged.
NOTICE In cold weather, the blades may freeze to the windshield, becoming stuck.
Operating the wipers in this condition may damage the wipers. Use the defroster to warm the windshield, then turn the wipers on.
If the vehicle speeds up while the wipers are operating intermittently, the length of the wipe interval shortens. When the vehicle starts moving, the wipers make a single sweep. When the vehicle speeds up, the wiper operation’s shortest delay setting (
) and the LO setting become the same.
Turn the washers off if no washer fluid comes out. The pump may get damaged.
The wiper motor is equipped with a breaker that may stop motor operation temporarily to prevent an overload. Wiper operation will return to normal within a few minutes, once the circuit has returned to normal.
If the wipers stop operating due to any obstacle such as the build-up of snow, park the vehicle in a safe place.
Rotate the wiper switch to OFF, and turn the ignition switch to ACCESSORY (q or LOCK (0 *1, then remove the obstacle.
TOC
Index
Home
117
2013 Accord Coupe
1Brightness Control
Instrument panel brightness varies, depending on whether the exterior lights are on or off. The instrument panel dims to reduce glare when they are on.
Pressing the display.
(Select/Reset) knob switches the
If you turn the knob to the right until the brightness display is up to max, the beeper sounds. This cancels the reduced instrument panel brightness when the parking lights are on.
The brightness can be set differently for when the exterior lights are on, and when they are off.
uuOperating the Switches Around the Steering WheeluBrightness Control
QRG
Brightness Control
Control Knob
When the parking lights are turned on and the ignition switch is in ON (w *1, you can use the brightness control knob to adjust instrument panel brightness. Brighten: Turn the knob to the right.
Dim: Turn the knob to the left.
You will hear the beeper when the brightness reaches minimum or maximum. The information display will return to its original state several seconds after you adjust the brightness.
■ Brightness level indicator The brightness level is shown on the information display while you are adjusting it.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
TOC
Index
Home
118
uuOperating the Switches Around the Steering WheeluRear Defogger/Heated Door Mirror* Button
Rear Defogger/Heated Door Mirror * Button Press the rear defogger and heated door mirror button to defog the rear window and mirrors when the ignition switch is in ON (w *1.
The rear defogger and heated door mirrors automatically switch off after 10-30 minutes depending on the outside temperature. However, if the outside temperature is 32°F (0°C) or below, they do not automatically switch off.
1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
2013 Accord Coupe
QRG
1Rear Defogger/Heated Door Mirror * Button
NOTICE When cleaning the inside of the rear window, be careful not to damage the heating wires.
It is critical to wipe the window from side to side along the defogger heating wires.
This system consumes a lot of power, so turn it off when the window has been defogged.
Also, do not use the system for a long period when the engine is idling. This may weaken the battery, making it difficult to start the engine.
TOC
Index
Home
119
uuOperating the Switches Around the Steering WheeluDriving Position Memory System *
QRG
Driving Position Memory System* You can store two driver’s seat positions with the driving position memory system. When you unlock and open the driver’s door with a remote, the seat adjusts automatically to one of the two preset positions.
2013 Accord Coupe
1Driving Position Memory System *
Using the audio/information screen, you can disable the automatic seat adjustment function.
2 Customized Features P. 273
• DRIVER 1 transmitter is linked to memory button 1.
• DRIVER 2 transmitter is linked to memory button 2.
DRIVER 1
DRIVER 2
TOC
Index
Home
120
* Not available on all models
uuOperating the Switches Around the Steering WheeluDriving Position Memory System *
2013 Accord Coupe
QRG
■ Storing a Position in Memory
Memory
Button 1
Memory
Button 2
SET Button
1. Set the power mode to ON. Adjust the
driver’s seat to the desired position.
2. Press the SET button.
uYou will hear a beep, and the memory
button indicator light will blink.
3. Press and hold memory button (1 or (2
within five seconds of pressing the SET button. uOnce the seat position has been
memorized, the indicator light on the button you pressed stays on.
■ Recalling the Stored Position
Memory
Button 1
Memory
Button 2
* Not available on all models
Automatic transmission/CVT models 1. Move the shift lever to (P.
All models 2. Apply the parking brake.
3. Press a memory button ((1 or (2).
uYou will hear a beep, and the indicator
•
light will blink.
The seat will automatically move to the memorized position. When it has finished moving, you will hear a beep, and the indicator light stays on.
1Storing a Position in Memory
After you press the SET button, the storing operation will be canceled when: • You do not press the memory button within five
seconds.
• You readjust the seat position before the double-
beep.
• You set the power mode to any position except
ON.
1Recalling the Stored Position
The seat will stop moving if you: • Press the SET button, or a memory button ((1 or
(2).
• Adjust the seat position. •
Automatic transmission/CVT models Shift into any position except (P. Manual transmission models Release the parking brake.
TOC
Index
Home
121
uuOperating the Switches Around the Steering WheeluAdjusting the Steering Wheel
QRG
Adjusting the Steering Wheel The steering wheel height and distance from your body can be adjusted so that you can comfortably grip the steering wheel in an appropriate driving posture.
To adjust
1. Pull the steering wheel adjustment lever up.
u The steering wheel adjustment lever is
under the steering column.
TOC
Lever
To lock
2. Move the steering wheel up or down, and
in or out. u Make sure you can see the instrument
panel gauges and indicators.
3. Push the steering wheel adjustment lever
down to lock the steering wheel in position. u After adjusting the position, make sure
you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
2013 Accord Coupe
1Adjusting the Steering Wheel
3WARNING
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
Make any steering wheel adjustments before you start driving.
Index
Home
122
Adjusting the Mirrors
Interior Rearview Mirror Adjust the angle of the rearview mirror when you are sitting in the correct driving position.
■ Rearview Mirror with Day and Night Positions*
Tab
Up
Flip the tab to switch the position. The night position will help to reduce the glare from headlights behind you when driving after dark.
Daytime Position
Down
Night Position
■ Automatic Dimming Rearview Mirror *
When driving after dark, the automatic dimming rearview mirror reduces the glare from headlights behind you. Press the auto button to turn this function on and off. When activated, the auto indicator comes on.
Indicator
Auto Button
Sensor
* Not available on all models
2013 Accord Coupe
QRG
1Adjusting the Mirrors
Keep the inside and outside mirrors clean and adjusted for best visibility.
Adjust the mirrors before you start driving.
2 Adjusting the Seat Positions P. 125
1Automatic Dimming Rearview Mirror*
The auto dimming function cancels when the shift position is in (R.
TOC
Index
Home
123
uuAdjusting the MirrorsuPower Door Mirrors
QRG
Power Door Mirrors
Selector Switch
You can adjust the door mirrors when the ignition switch is in ON (w *1.
2013 Accord Coupe
■ Mirror position adjustment L/R selector switch: Select the left or right mirror. After adjusting the mirror, return the switch to the center position.
Mirror position adjustment switch: Press the switch left, right, up, or down to move the mirror.
Adjustment Switch
TOC
■ Expanded View Driver's Mirror
Outer Segment
Inner Segment
The driver side door mirror has outer and inner segments.
The outer segment is slightly curved to provide a wider angle view than a standard flat mirror. This wider view may help you check areas that are not visible using a standard door mirror.
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
1Expanded View Driver's Mirror
Objects visible in the outer segment of the driver side door mirror appear smaller than objects in the rest of the mirror. But in fact, they are closer than they appear.
Do not rely on your mirrors. Always look to the side and behind your vehicle before changing lanes.
Index
Home
124
Adjusting the Seats
Adjusting the Seat Positions
2013 Accord Coupe
QRG
Allow sufficient space.
Adjust the driver's seat as far back as possible while allowing you to maintain full control of the vehicle. You should be able to sit upright, well back in the seat and be able to adequately press the pedals without leaning forward, and grip the steering wheel comfortably. The passenger's seat should be adjusted in a similar manner, so that it is as far back from the front airbag in the dashboard as possible.
1Adjusting the Seats
3WARNING
Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate.
Always sit as far back from the front airbags as possible while maintaining control of the vehicle.
Move back.
■ Adjusting the driver’s power seat *
Horizontal Position Adjustment
Height Adjustment
The National Highway Traffic Safety Administration and Transport Canada recommend that drivers allow at least 10 inches (25 cm) between the center of the steering wheel and the chest.
Lumbar Support Adjustment
Always make seat adjustments before driving.
Seat-back Angle Adjustment
* Not available on all models
Continued
TOC
Index
Home
125
uuAdjusting the SeatsuAdjusting the Seat Positions
■ Adjusting the front manual seat(s)
Height Adjustment (Driver side only) Pull up or push down the lever to raise or lower the seat.
2013 Accord Coupe
1Adjusting the front manual seat(s)
Once a seat is adjusted correctly, rock it back and forth to make sure it is locked in position.
Horizontal Position Adjustment Pull up on the bar to move the seat, then release the bar.
Driver’s seat is shown.
Seat-back Angle Adjustment Pull up the lever to change the angle.
QRG
TOC
Index
Home
126