Before driving
Introduction
Instrumentation
Controls and features
Seating and safety restraints
Starting and driving
Starting
Driving
Roadside emergencies
Servicing
Maintenance and care
Capacities and specifications
Customer assistance
Reporting safety defects
Index
Contents
20
89
123
128
158
184
240
249
262
263
All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation. Copyright © 2001 Ford Motor Company
Introduction
The following warning may be required by California law: CALIFORNIA Proposition 65 Warning
WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to
the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
ICONS Indicates a safety alert. Read the following section on Warnings.
Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regarding child safety restraints. Refer to Seating and safety restraints for more information.
Indicates that this Owner Guide contains information on this subject. Please refer to the Index to locate the appropriate section which will provide you more information.
Introduction
WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment.
BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in.
INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
EMISSION WARRANTY The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Introduction
SPECIAL NOTICES
Notice to owners of pickup trucks and utility type vehicles
Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read Driving off road in the Driving chapter as well as the “Four Wheeling” supplement included with 4WD and utility type vehicles.
Using your vehicle with a snowplow
Do not use this vehicle for snowplowing.
Introduction
Using your vehicle as an ambulance
Do not use this vehicle as an ambulance.
Your vehicle is not equipped with the Ford Ambulance Preparation Package.
Electric vehicles For information on operating your Electric Vehicle, also refer to the Electric Vehicle Owner’s Guide Supplement.
Introduction
These are some of the symbols you may see on your vehicle.
Vehicle Symbol Glossary
Safety Alert
See Owner’s Guide
Fasten Safety Belt
Air Bag-Front
Air Bag-Side
Child Seat
Child Seat Installation Warning
Child Seat Tether Anchorage
Brake System
Anti-Lock Brake System
Brake Fluid - Non-Petroleum Based
Traction Control
Master Lighting Switch
Hazard Warning Flasher
Fog Lamps-Front
Fuse Compartment
Fuel Pump Reset
Windshield Wash/Wipe
Rear Window Defrost/Demist
Power Window Lockout
Windshield Defrost/Demist
Power Windows Front/Rear
Introduction
Vehicle Symbol Glossary
Child Safety Door Lock/Unlock
Interior Luggage Compartment Release Symbol
Panic Alarm
Engine Oil
Engine Coolant
Engine Coolant Temperature
Do Not Open When Hot
Battery
Avoid Smoking, Flames, or Sparks
Battery Acid
Explosive Gas
Fan Warning
Power Steering Fluid
Maintain Correct Fluid Level
MAX MIN
Emission System
Engine Air Filter
Passenger Compartment Air Filter
Jack
Check fuel cap
Instrumentation
Instrument panel dimmer control
(pg. 21)
Instrument cluster
(pg. 10)
60 70
0 0 0
50
80
100
120
0 0 0 0 0 0
DOOR AJAR
40
60
30
40
20
20
10 MPH
80
140
90
001
160
180
101
km/h
201
R N D 2 1
THEFT
Headlamp control
(pg. 20)
CHECK GAGE
RPMx1000
CHECK ENGINE
CHECK FUEL CAP
ABS
BRAKE
OFF
DIM
ON
OFF
Turn signal control
(pg. 64)
Wiper/washer control
(pg. 71)
Driver air bag
(pg. 103)
Parking brake release
(pg. 129)
SPEED CONT
4WD HIGH
4WD LOW
O/D OFF
SET ACC
COAST
Speed control*
(pg. 65)
Hood release
(pg. 185)
Instrumentation
Auxiliary
power point
(pg. 28)
4wd control*
(pg. 139)
Audio system
(pg. 29)
4X4
HIGH
4X4
LOW
2WD
VOL PUSH ON
TONE
CLK
TONE VOL
ST DX FM
12
SEEK
TUNE
AM/FM
OFF
ON
OFF
OFF
PASSENGER AIRBAG
Passenger air bag deactivate switch
(pg. 108)
Climate control
system (pg. 22)
Fog lamp control
(pg. 20)
* if equipped
Instrumentation
WARNING LIGHTS AND CHIMES
CHECK ENGINE
Check engine Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service technician in properly servicing your vehicle. The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing. Whatyoushoulddoifthecheckenginelightilluminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Check Engine light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel.
10
Instrumentation
3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the Check Engine light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
CHECK FUEL CAP
Check fuel cap (if equipped) Momentarily illuminates when the ignition is turned to the ON position to ensure your bulb is working. When this light turns on, check the fuel filler cap. Continuing to operate the vehicle with the check fuel cap light on, can activate the Service Engine Soon/Check Engine warning light. When the fuel filler cap is properly re-installed, the light(s) will turn off after a period of normal driving. This period will vary depending on driving conditions. It may take a long period of time for the system to detect an improperly installed fuel filler cap. For more information, refer to Fuel filler cap in the Maintenance and care chapter.
11
Instrumentation
Check gage Illuminates when the engine coolant temperature is high, the engine oil pressure is low or the fuel gauge is at or near empty. The ignition must be in the ON position for this lamp to illuminate. The lamp will also stay illuminated after the ignition is turned to the ON position. Refer to Engine coolant temperature gauge, Engine oil pressure gauge or Fuel gauge in this chapter for more information.
CHECK GAGE
Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately.
Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter.
Brake system warning Momentarily illuminates when the ignition is turned to the ON position to indicate a system check. Also illuminates if the parking brake is engaged. If the brake warning lamp does not illuminate at these times, seek service immediately. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately.
BRAKE
12
Instrumentation
Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON position to indicate a system check. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released.
ABS
Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter.
High beams Illuminates when the high beam headlamps are turned on.
Anti-theft system (if equipped) Refer to SecuriLocky passive anti-theft system in the Controls and features chapter.
Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service.
THEFT
13
Instrumentation
O/D off (if equipped) Illuminates when the Transmission Control Switch (TCS), refer to Overdrive control in the Controls and Features chapter, has been pushed turning the transmission overdrive function OFF. When the light is on, the transmission does not operate in the overdrive mode, refer to the Driving chapter for transmission function and operation. The light may also flash steadily if a transmission malfunction is detected. If the light does not come on when the Transmission Control Switch is depressed or if the light flashes steadily, have your vehicle serviced as soon as possible, damage to the transmission could occur.
O/D OFF
Four wheel drive low (if equipped) Momentarily illuminates after the engine is started. Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced.
Four wheel drive high (if equipped) Momentarily illuminates after the engine is STARTED. Illuminates when four-wheel drive high is engaged. If the light continues to flash have the system serviced.
Door ajar Illuminates when the ignition is in the ON position and any door is open. It may also momentarily illuminate after the engine is started and all doors are closed.
4WD LOW
DOOR AJAR
14
Instrumentation
Speed control This light comes on when either the SET/ACCEL or RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake or clutch (if equipped) is applied or the ignition is turned to the OFF position.
SPEED CONT
Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter.
Belt minder chime Sounds intermittently to remind you to fasten your safety belts. For information on the safety belt minder chime, refer to the Seating and safety restraints chapter.
Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter.
Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened.
Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened.
15
Instrumentation
GAUGES
Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty, there is a small amount of reserve fuel in the tank. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel filler door is located.
16
Instrumentation
Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. Refer to Engine coolant in the Maintenance and care chapter.
Never remove the coolant reservoir cap and/or the radiator cap while the engine is running or hot, this may result in serious
burns.
NOTE: This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate.
Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
RPMx1000
17
Instrumentation
Speedometer Indicates the current vehicle speed.
40
60 70
0 0 0
50
80
100
120
0 0 0 0 0 0
60
30
40
20
20
10 MPH
80
140
90
001
160
180
101
km/h
201
Odometer Registers the total kilometers (miles) of the vehicle.
40
60 70
0 0 0
50
80
100
120
0 0 0 0 0 0
80
140
90
001
160
60
30
40
20
20
10 MPH
180
101
km/h
201
80
140
90
001
160
180
101
km/h
201
60 70
0 0 0
50
80
100
120
0 0 0 0 0 0
Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control.
40
60
30
40
20
20
10 MPH
18
Instrumentation
Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level. Add oil if needed (refer to Engine oil in the Maintenance and care chapter). If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician.
Battery voltage gauge This shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated by arrows), have the vehicle’s electrical system checked as soon as possible.
19
Controls and features
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps.
OFF
Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is in either of the following positions: † Parking lamps † Low beams Press the foglamp control to activate the foglamps. The foglamp indicator light will illuminate. When the highbeams are activated, the foglamps will not operate. Press the foglamp control again to deactivate the foglamps.
Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: † the ignition must be in the ON position and † the headlamp control is in the OFF or Parking lamps position.
Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
20
Controls and features
High beams † Push forward to activate. † Pull toward you to deactivate.
Flash to pass Pull toward you to activate and release to deactivate.
PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. † Rotate up to brighten. † Rotate down to dim. † Rotate to full up position (past detent) to turn on interior and cargo lamps.
† Rotate to full down position (past detent) to turn off interior and
cargo lamps.
DIM
21
Controls and features
CLIMATE CONTROL SYSTEM
Heater only system (if equipped)
OFF
Fanspeedcontrol Controls the volume of air circulated in the vehicle.
Temperaturecontrolknob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature. Modeselectorcontrol Controls the direction of the airflow to the inside of the vehicle.
OFF
registers.
(Panel)-Distributes outside air through the instrument panel
† † (Panel and floor)-Distributes outside air through the instrument † OFF-Outside air is shut out and the fan will not operate. For short
panel registers and the floor ducts.
periods of time only, use this mode to prevent undesirable odors from entering the vehicle.
(Floor)-Allows for maximum heating. Distributes outside air
through the floor ducts.
(Floor and defrost)-Distributes outside air through the floor ducts
and the windshield defroster ducts.
(Defrost)-Distributes outside air through the windshield defroster
ducts. It can be used to clear ice or fog from the windshield.
† † †
22
Controls and features
Operatingtips † In humid weather conditions, place the climate control system in
DEF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired.
† To reduce humidity buildup inside the vehicle in cold weather
conditions, do not drive with the climate control system in the OFF position.
† Under normal weather conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. † Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants.
airflow to the rear seats (if equipped).
† Don’t put objects under the front seat that will interfere with the † Remove any snow, ice or leaves from the air intake area at the base of the windshield.
† Do not place objects over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Avoid placing small objects on top of the instrument panel. These objects may fall down into the defroster outlets and block airflow, in addition to damaging the climate control system.
Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
23
Controls and features
Manual heating and air conditioning system (if equipped)
OFF
A/C
MAX A/C
Fanspeedcontrol Controls the volume of air circulated in the vehicle.
Temperaturecontrolknob Controls the temperature of the airflow inside the vehicle.
Modeselectorcontrol Controls the direction of the airflow to the inside of the vehicle.
OFF
A/C
MAX A/C
. However, the air conditioning will only function if the outside
The air conditioning compressor can operate in all modes except and temperature is about 6°C (43°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. † MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.
† A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C
but not as economical. Airflow will be from the instrument panel registers.
24
Controls and features
†
†
†
†
†
(Panel)-Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. † OFF-Outside air is shut out and the fan will not operate. For short
periods of time only, use this mode to prevent undesirable odors from entering the vehicle.
(Panel and floor)-Distributes outside air through the instrument
panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
(Floor)-Allows for maximum heating by distributing outside air
through the floor ducts. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode.
(Floor and defrost)-Distributes outside air through the windshield
defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defrost ducts. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.
(Defrost)-Distributes outside air through the windshield defroster
ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.
Operatingtips † In humid weather conditions, place the climate control system in
DEF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired.
† To reduce humidity buildup inside the vehicle in cold weather
conditions, don’t drive with the climate control system in the OFF or MAX A/C position.
25
Controls and features † To reduce humidity buildup inside the vehicle in warm weather
conditions, don’t drive with the climate control system in the OFF position.
† Under normal weather conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. † Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants.
† If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Once the vehicle has been “aired out”, operate the climate control system as desired. † Do not put objects under the front seat that will interfere with the † Remove any snow, ice or leaves from the air intake area at the base of the windshield.
airflow to the back seats (if equipped).
† Do not place objects over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Avoid placing small objects on top of the instrument panel. These objects may fall down into the defroster outlets and block airflow, in addition to damaging the climate control system.
26
Controls and features
To aid in defogging/demisting in cold weather conditions: 1. Select 2. Set the temperature control to full heat 3. Set the fan speed to HI 4. Direct the outer panel vents towards to side windows To increase airflow to the outer panel vents, close the central panel vents.
Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information.
4X4
HIGH
4X4
LOW
2WD
27
Controls and features
AUXILIARY POWER POINT
SEEK
TUNE
12V
AM-FM
OFF
A/C
MAX A/C
Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. This outlet should be used in place of the cigarette lighter for optional electrical accessories.
28
Controls and features
PASSENGER AIR BAG ON/OFF SWITCH This switch must be used to deactivate the passenger air bag whenever a child seat is used in the right front or center front passenger seat position. Refer to Passenger air bag ON/OFF switchin the Seating and safety restraints chapter.
ON
OFF
OFF
PASSENGER AIRBAG
USING YOUR AUDIO SYSTEM
AM/FM Stereo
VOL PUSH ON
TONE
CLK
TONE VOL
ST DX FM
12
SEEK
TUNE
AM/FM
29
Controls and features
Volume/powercontrol Press the control to turn the audio system on or off.
Turn the control to raise or lower volume.
VOL PUSH ON
VOL PUSH ON
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FMselect The AM/FM select control works in radio mode.
AM/FM
AM/FMselectinradiomode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tuneadjust The tune control works in radio mode.
30
Controls and features
SEEK
TUNE
Tuneadjustinradiomode † Press
to move to the next
frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
† Press
to move to the next frequency up the band (whether or not
a listenable station is located there). Hold for quick movement.
Seekfunction The seek function control works in radio mode. Seekfunctioninradiomode † Press
to find the next listenable station down the frequency band.
† Press
to find the next
listenable station up the frequency band.
SEEK
TUNE
Radiostationmemorypreset The radio is equipped with four station memory preset controls. These controls can be used to select up to four preset AM stations and eight FM stations (four in FM1 and four in FM2). Settingmemorypresetstations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
31
Controls and features
Bassadjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the TONE control once, then use the volume knob to adjust the desired level.
Trebleadjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TONE control twice, then use the volume knob to adjust the desired level.
Speakerbalanceadjust Speaker sound distribution can be adjusted between the right and left speakers. Press the TONE control three times, then use the volume knob to adjust the desired level.
Settingtheclock Press CLK to toggle between listening frequencies and clock mode. To set the hour, press and hold the CLK control until CLOCK SET appears in the display and press the SEEK control:
32
VOL PUSH ON
VOL PUSH ON
VOL PUSH ON
TONE
CLK
TONE
CLK
TONE
CLK
TONE
CLK
† †
to decrease hours and to increase hours.
Controls and features
To set the minute, press and hold the CLK control until CLOCK SET appears in the display and press the TUNE control:
SEEK
TUNE
SEEK
TUNE
TONE
CLK
SEEK
SEEK
TUNE
to decrease minutes and to increase minutes.
† † The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information. Any time that the media is changed, (new radio station, etc.), the media information will again display for ten seconds before reverting back to the clock. In media mode, the media information will always be displayed.
TUNE
33
Controls and features
AM/FM Stereo / Single CD Radio
VOL - PUSH ON
AM FM
CD
BASS
TREB
FM1
ST
BAL
FADE
SEEK
TUNE DISCS
DISC
SCN
CLK
EJ
COMP
CD
CD
SHUFFLE
Volume/powercontrol Press the control to turn the audio system on or off.
VOL - PUSH ON
Turn the control to raise or lower volume.
VOL - PUSH ON
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
34
AM/FMselect The AM/FM select control works in radio and CD modes.
Controls and features
AM FM
CD
AM/FMselectinradiomode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FMselectinCDmode Press this control to stop CD play and begin radio play. Tuneadjust The tune control works in radio and CD changer mode (if equipped). Tuneadjustinradiomode † Press
to move to the next
frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
† Press
SEEK
TUNE DISCS
to move to the next frequency up the band (whether or not
a listenable station is located there). Hold for quick movement.
35
Controls and features
TuneadjustforCDchanger(ifequipped) † Press
to select the previous
disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc.
TUNE DISCS
SEEK
to select the next disc in the CD changer. Hold the control
to fast-forward through the remaining discs.
† Press
Seekfunction The seek function control works in radio or CD mode. Seekfunctioninradiomode † Press
to find the next listenable station down the frequency band.
to find the next
listenable station up the frequency band.
† Press
SeekfunctionforCDmode † Press
to seek to the previous
track of the current disc. If a selection has been playing for three seconds or more and you , the CD changer will press replay that selection from the beginning. † Press
SEEK
TUNE DISCS
SEEK
TUNE DISCS
to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.
Scanfunction The scan function works in radio or CD mode.
SCN
36
Controls and features
Scanfunctioninradiomode Press SCN to hear a brief sampling of all listenable stations on the frequency band. Press SCN again to stop the scan mode. ScanfunctioninCDmode Press SCN to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again. Bassadjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Trebleadjust The treble adjust control allows you to increase or decrease the audio system’s treble output.
Speakerbalanceadjust Speaker sound distribution can be adjusted between the right and left speakers.
BASS
TREB
BAL
37
Controls and features
Speakerfadeadjust Speaker sound can be adjusted between the front and rear speakers.
CDselect † To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
FADE
AM FM CD
Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Rewind The rewind control works in CD and CD changer (if equipped) modes. To rewind in CD mode press the CD control (preset 1). Pressing the control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fastforward The fast forward control works in CD mode. To fast forward in CD mode, press the CD control (preset 2). Pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action.
CD
CD
38
Controls and features
Ejectfunction Press the control to stop and eject a CD.
EJ
COMP
Compressionfeature Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shufflefeature(ifequippedwithCDchanger) The shuffle feature operates in CD changer mode only and plays all tracks on the current disc in random order. The shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Settingtheclock Press CLK to toggle between listening frequencies and clock mode while in radio mode. To set the hour, press and hold the CLK control and press the SEEK control:
SCN
SHUFFLE
CLK
† †
to decrease hours and to increase hours.
SEEK
TUNE DISCS
39
Controls and features
To set the minute, press and hold the CLK control and press the TUNE control:
† †
to decrease minutes and to increase minutes.
SEEK
TUNE DISCS
SEEK
TUNE
SEEK
TUNE
Premium AM/FM Stereo/Cassette/Single CD
VOL PUSH ON
DISC
FM 1
AMC
BL
ST
RF
DOLBY B NR
EJ
TAPE
CD
SCAN
BASS
TREB
FF
SIDE 1-2
SEL
BAL
FADE
COMP
SHUFFLE
EJ
MUTE
AUTO
CLK
AM
FM
SEEK
TUNE
REW
40
Controls and features
VOL - PUSH ON
Volume/powercontrol Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control.
Turn control to raise or lower volume.
VOL - PUSH ON
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FMselect The AM/FM select control works in radio, tape and CD modes.
AM
FM
AM/FMselectinradiomode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FMselectintapemode Press this control to stop tape play and begin radio play. Tuneadjust The tune control works in radio mode.
41
Controls and features
Tuneadjustinradiomode † Press
to move to the next
frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
† Press
to move to the next
frequency up the band (whether or not a listenable station is located there). Hold for quick movement.
Seekfunction The seek function control works in radio, tape or CD mode. Seekfunctioninradiomode † Press
to find the next listenable station down the frequency band.
to find the next
listenable station up the frequency band.
† Press
to listen to the previous selection on the tape. to listen to the next selection on the tape.
Seekfunctionintapemode † Press † Press SeekfunctioninCDmode † Press † Press
track of the disc.
to seek to the previous
to seek forward to the
next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.
Scanfunction The scan function works in radio, tape or CD mode.
SCAN
42
Controls and features
Scanfunctioninradiomode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scanfunctionintapemode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again. ScanfunctioninCDmode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again. Radiostationmemorypreset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Settingmemorypresetstations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station.
AM
FM
REW
FF
SIDE 1-2
COMP
SHUFFLE
3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Autosetmemorypreset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations.
43
Controls and features
CLK
AUTO
Startingautosetmemorypreset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. These stations are temporarily stored in the memory preset controls (until deactivated) and are accessed in the same manner as your original presets. To deactivate autoset and return to your audio system’s manually set memory stations, press the AUTO control again. Bassadjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: † to decrease the bass output †
to increase the bass output.
BASS
TREB
and
SEL
44
Trebleadjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: † to decrease the treble output †
to increase the treble output.
and
Controls and features
BASS
TREB
SEL
Speakerbalanceadjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: † †
to shift sound to the left and to shift sound to the right.
BAL
FADE
SEL
Speakerfadeadjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: † †
to shift the sound to the
to shift the sound to the rear.
front and
BAL
FADE
SEL
45
Controls and features
Tapeselect † To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.
TAPE
CD
continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. † In CD mode, pressing the REW control rewinds the CD within the
Rewind The rewind control works in tape and CD modes. † In tape mode, radio play will
current track.
Fastforward The fast forward control works in tape and CD modes. † In the tape mode, tape direction will automatically reverse when the end of the tape is reached.
REW
FF
† In CD mode, pressing the control fast forwards the CD within the
current track.
Tapedirectionselect Press SIDE 1–2 to play the alternate side of a tape.
Ejectfunction Press the EJ control to stop and eject a tape.
SIDE 1-2
EJ
46
Controls and features
Press the EJ control to stop and eject a CD.
EJ
control to activate (and deactivate) the Dolbyt noise
are registered trademarks of Dolbyt Laboratories Licensing
DolbyT noisereduction Dolbyt noise reduction operates in tape mode. Dolbyt noise reduction reduces the amount of hiss and static during tape playback. Press the reduction. Dolbyt noise reduction is manufactured under license from Dolbyt Laboratories Licensing Corporation. “Dolbyt” and the double-D symbol Corporation. Compressionadjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shufflefeature The shuffle feature operates in CD mode and plays all tracks in random order. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again.
COMP
SHUFFLE
47
AUTO
CLK
AUTO
CLK
Controls and features
Settingtheclock To set the hour, press and hold the CLK control and press SEEK:
† †
to decrease hours and to increase hours.
To set the minute, press and hold the CLK control and press TUNE:
to decrease minutes and to increase minutes.