2015 Ford Mustang Owners Manual

WARNING

The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting

during low visibility driving conditions. Also, the autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog. Make sure the headlamps are switched to auto or on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash. Type 1 - Conventional (Non- Configurable) The daytime running lamps turn on when: 1. The ignition is switched to the on

position.

2. The transmission is not in park (P) for vehicles with automatic transmissions or the parking brake is released for vehicles with manual transmissions.

3. The lighting control is in the off, parking

lamp or autolamps positions.

4. The headlamps are off. Type 2 - Configurable Switch the daytime running lamps on or off using the information display controls. The daytime running lamps turn on when: 1. They are switched on in the information

display.

2. The ignition is switched to the on

position.

3. The transmission is not in park (P) for vehicles with automatic transmissions or the parking brake is released for vehicles with manual transmissions.

Press repeatedly or press and hold to dim. Press repeatedly or press and hold to brighten.

HEADLAMP EXIT DELAY After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on.

71

Mustang (CZG), enUSA, Third Printing

ABE165366Lighting

DIRECTION INDICATORS

4. The lighting control is in the autolamps

position.

5. The headlamps are off. The other lighting control switch positions do not activate the daytime running lamps, and you can use them to temporarily override autolamp control. When switched off in the information display, the daytime running lamps are off in all lighting control switch positions. FRONT FOG LAMPS (If Equipped)

Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change. WELCOME LIGHTING (If Equipped) Pony Projection Lights The pony projection lights are on the bottom of the exterior mirror housings. They will project an image onto the ground a short distance from your vehicle when welcome lighting or lighted entry turns on. Note: Moisture, frost and ice build-up or other types of contamination on the surface of the light lens can cause non-permanent distortion or reduced brightness of the image. Do not use abrasive materials to clean the lens. INTERIOR LAMPS The lamps turn on when: • •

You open any door. You press a button on the remote control. You press a map lamp button.

Press the control to switch the fog lamps on or off. You can switch the fog lamps on when the lighting control is in any position except Off and the high beams are not on.

•

72

Mustang (CZG), enUSA, Third Printing

E142453E162681Lighting

Map Lamps

Left-hand side map lamp. Right-hand side map lamp.

You can switch the lamps on individually by pressing the buttons. AMBIENT LIGHTING (If Equipped) You can adjust the ambient lighting system in your information display. See Information Displays (page 84).

73

Mustang (CZG), enUSA, Third Printing

E175199Windows and Mirrors

Bounce-Back (Coupe Only) The window will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature

WARNING

When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care

when closing the windows to avoid personal injury or damage to your vehicle.

Pull up the window switch and hold within two seconds of the window reaching the bounce-back position. The window will travel up with no bounce-back protection. The window will stop if you release the switch before the window is fully closed. Accessory Delay You can use the window switches for several minutes after you switch the ignition off or until you open either front door. GLOBAL OPENING (If Equipped) You can use the remote control to operate the windows with the ignition off. Note: You can enable or disable this feature in the information display, or see an authorized dealer. See General Information (page 84). Note: To operate this feature, accessory delay must not be active.

POWER WINDOWS WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

children and pets are not in the proximity of the window openings.

Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise. Note: Use the singular control (if equipped) to open both rear windows. Press the switch to open the window. Lift the switch to close the window. One-Touch Down Press the switch fully and release it. Press again or lift it to stop the window. One-Touch Up (Coupe Only) Lift the switch fully and release it. Press or lift it again to stop the window.

74

Mustang (CZG), enUSA, Third Printing

E180087Windows and Mirrors

Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Heated Exterior Mirrors (If Equipped) See Heated Windows and Mirrors (page 107). Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memory function. See Power Seats (page 111). Auto-Dimming Feature (If Equipped) The driver exterior mirror automatically dims when the interior auto-dimming mirror turns on. Signal Indicator Mirrors (If Equipped) The outer portion of the appropriate mirror housing will blink when you switch on the turn signal. Pony Projection Lights (If Equipped) The lights are on the bottom of the mirror housings. This feature projects an image onto the ground a short distance from the vehicle with the illuminated entry and exit feature. Note: Moisture, frost and ice build-up (or other types of contamination) on the surface of the light lens can cause some non-permanent distortion or reduced brightness of the image. Do not use abrasive materials to clean the lens.

Opening the Windows You can open the windows for a short time after you unlock your vehicle with the remote control. After you unlock your vehicle, press and hold the remote control unlock button to open the windows. Release the button once movement starts. Press the lock or unlock button to stop movement. EXTERIOR MIRRORS Power Exterior Mirrors WARNING

Do not adjust the mirrors when your vehicle is moving.

Left-hand mirror Adjustment control Right-hand mirror

To adjust a mirror: 1. Select the mirror you want to adjust.

The control will illuminate.

2. Adjust the position of the mirror. 3. Press the mirror switch again.

75

Mustang (CZG), enUSA, Third Printing

E176804Windows and Mirrors

Integrated Blind Spot Mirrors (If Equipped)

WARNING

Objects in the blind spot mirror are closer than they appear.

Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They can increase your visibility along the side of your vehicle. Check the main mirror first before a lane change, then check the blind spot mirror. If the blind spot mirror does not show any vehicles in its viewing area and the traffic in the adjacent lane is at a safe distance, signal that you intend to change lanes. Glance over your shoulder to verify traffic is clear and carefully change lanes.

The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C). Blind Spot Monitor (If Equipped) See Blind Spot Information System (page 162). INTERIOR MIRROR WARNING

Do not adjust the mirror when your vehicle is moving.

Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. In addition to the standard pivot point, this mirror also includes a second pivot point, letting you move the mirror head up or down and from side to side. Auto-Dimming Mirror Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor.

76

Mustang (CZG), enUSA, Third Printing

ABCE138665Windows and Mirrors

To reduce glare, the mirror dims automatically when it detects bright lights from behind your vehicle. It automatically returns to normal reflection when you select reverse (R) gear to make sure you have a clear view when backing up. SUN VISORS

Rotate the sun visor toward the side window and extend it rearward for extra shade. Illuminated Vanity Mirror

Lift the cover to switch the lamp on.

77

Mustang (CZG), enUSA, Third Printing

E138666E162197Instrument Cluster

GAUGES

Tachometer (Revolutions per minute) Information display Speedometer (Ground speed) Fuel gauge Engine coolant temperature gauge

Information Display Odometer Located in the bottom of the information display. Registers the accumulated distance your vehicle has traveled. Trip Computer See General Information (page 84). Vehicle Settings and Personalization See General Information (page 84). Fuel Gauge Note: The fuel gauge may vary slightly when your vehicle is moving or on a gradient.

Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located. The needle should move toward F when you refuel your vehicle. If the needle points to E after adding fuel, this indicates your vehicle needs service soon. After refueling some variability in needle position is normal:

78

Mustang (CZG), enUSA, Third Printing

E174486Instrument Cluster

•

•

•

It may take a short time for the needle to reach F after leaving the gas station. This is normal and depends upon the slope of pavement at the gas station. The fuel amount dispensed into the tank is a little less or more than the gauge indicated. This is normal and depends upon the slope of pavement at the gas station. If the gas station nozzle shuts off before the tank is full, try a different gas pump nozzle.

Low Fuel Reminder Vehicles with no distance-to-empty display A low fuel reminder triggers when the fuel gauge needle is at 1/16th. Vehicles equipped with distance-to- empty display A low fuel reminder triggers when the fuel gauge needle is at 1/16th or about 35 miles (56km) to empty, whichever occurs first.

Variations: Note: The low fuel warning and distance-to-empty warning can appear at different fuel gauge positions depending on fuel economy conditions. This variation is normal.

Driving type (fuel economy

conditions)

Highway driving

Severe duty driving (trailer

towing, extended idle)

Fuel gauge position

Distance-to-empty

1/16th

1/16th-1/4

35 miles to 80 miles (56 km

to 129 km)

10 miles to 35 miles (16 km

to 56 km)

Gauge Package (If Equipped)

Oil Pressure Gauge Indicates the engine oil pressure.

Engine Coolant Temperature Gauge

WARNING

Never remove the coolant reservoir cap while the engine is running or hot.

Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop your vehicle as soon as safely possible, switch off the engine and let it cool.

79

Mustang (CZG), enUSA, Third Printing

E196366Instrument Cluster

Battery

If it illuminates while driving, it indicates a malfunction. Switch off all unnecessary electrical

equipment and have the system checked by your authorized dealer immediately. Blind Spot Monitor (If Equipped)

It will illuminate when you switch this feature off or in conjunction with a message. See Blind Spot

Information System (page 162). See Information Messages (page 92). Brake System

It will illuminate when you engage the parking brake with the ignition on.

If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.

WARNING

Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Cruise Control (If Equipped)

It will illuminate when you switch this feature on.

Vacuum/Boost Gauge Indicates the vacuum and boost pressure in the intake. WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information. Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle. Adaptive Cruise Control (If Equipped)

The speed control system indicator light changes color to indicate what mode the system is in: See Using Adaptive Cruise Control (page 155). On (white light): Illuminates when the adaptive cruise control system is turned on. Turns off when the speed control system is turned off. Engaged (green light): Illuminates when the adaptive cruise control system is engaged. Turns off when the speed control system is disengaged. Anti-Lock Braking System

If it illuminates when you are driving, this indicates a malfunction. You will continue

to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer.

80

Mustang (CZG), enUSA, Third Printing

E144524E151262E144522E71340Instrument Cluster

Direction Indicator

Front Airbag

Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the

indicators stay on or flash faster, check for a burned out bulb. See Changing a Bulb (page 225). Door Ajar

Displays when the ignition is on and any door is not completely closed.

Engine Coolant Temperature

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as

possible, switch off the engine and let cool. See Engine Coolant Check (page 216). Engine Oil

If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 215). Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by your authorized dealer immediately. Fasten Safety Belt

It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety

Belt Minder (page 34).

If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer. Front Fog Lamps (If Equipped)

Lights when you switch the front fog lamps on.

Heads Up Display (If Equipped) A red beam of lights will illuminate on the windshield in certain instances when using adaptive cruise control or the collision warning system. It will also illuminate momentarily when you start your vehicle to make sure the display works. High Beam

It will illuminate when you switch the high beam headlamps on. It will flash when you use the

headlamp flasher. Low Fuel Level

It will illuminate when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as

possible. Low Tire Pressure Warning

It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check

your tire pressures as soon as possible.

81

Mustang (CZG), enUSA, Third Printing

E156133Instrument Cluster

It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by your authorized dealer. Parking Lamps

It will illuminate when you switch the parking lamps on.

Service Engine Soon

If the service engine soon indicator light stays illuminated after the engine is started, it

indicates that the On Board Diagnostics system (OBD) has detected a malfunction of the vehicle emissions control system. Refer to On board diagnostics (OBD) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 132). If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

WARNING

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic

converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Have an authorized dealer service your vehicle immediately.

The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing.

Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 132). Stability Control

It will flash when the system is active. If it remains illuminated or does not illuminate when you

switch the ignition on, this indicates a malfunction. During a malfunction the system will switch off. Have the system checked by your authorized dealer immediately. See Using Stability Control (page 146). Stability Control Off

It will illuminate when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off. See Using Stability Control (page 146).

AUDIBLE WARNINGS AND INDICATORS Keyless Warning Alert The horn will sound twice when you exit your vehicle with the intelligent access key and your vehicle is in RUN, indicating your vehicle is still on. Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on.

82

Mustang (CZG), enUSA, Third Printing

E138639Instrument Cluster

Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately.

83

Mustang (CZG), enUSA, Third Printing

Information Displays

GENERAL INFORMATION

Information Display Controls

WARNING

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

Various systems on your vehicle can be controlled using the information display controls on the steering wheel. Corresponding information is displayed in the information display.

• Press the up and down arrow buttons

to scroll through and highlight the options within a menu.

• Press the right arrow button to enter a

sub-menu.

• Press the left arrow button to exit a

menu.

• Press and hold the left arrow button at

any time to return to the main menu display (escape button).

• Press the OK button to choose and

confirm settings or messages.

Main menu • Gauge Mode • •

Trip/Fuel Track Apps

84

Mustang (CZG), enUSA, Third Printing

E174488Information Displays

Settings

• Driver Assist • Note: Some options may appear slightly different or not at all if the items are optional.

Gauge Mode Use the arrow buttons to choose between the following gauge options.

Gauge Mode

Distance to Empty - XXX miles Tire Pressure – Tire Pressure on Demand Screen Gauge Detail

Air/Fuel Ratio Boost/Vac Cyl Head Inlet Air Oil Pressure Oil Temp Trans Temp Voltage

Virtual gauge shown

Virtual gauge shown

Note: In order to provide real-time values, some gauges may display more value fluctuation than other gauges during normal operation. Some gauges shown in standard measure. Metric similar. Tire Pressure

Air/Fuel Ratio

Displays the current air to fuel mixture in the engine.

Displays your current vehicle tire pressures.

85

Mustang (CZG), enUSA, Third Printing

E182200E174490Information Displays

Boost/Vac (If Equipped)

Oil Temp

Displays the vacuum or boost pressure.

Cyl Head

Displays the engine oil temperature. If the temperature rises to the red area, stop in a safe place and let your vehicle cool. If the problem persists, see an authorized dealer.

Trans Temp (Automatic Transmission only)

Displays the engine’s cylinder head temperature.

Inlet Air

Displays the temperature of the air in the cold air inlet tube.

Displays the transmission fluid operating temperature. If the temperature rises to the red area, stop in a safe place and let the transmission cool. If the problem persists, see an authorized dealer.

Voltage

Displays your vehicle’s battery voltage. If the voltage is consistently too high or very low, see an authorized dealer.

86

Mustang (CZG), enUSA, Third Printing

E174496E174491E174492E174493E174494E174495Information Displays

Trip/Fuel

Use the arrow buttons to choose between the following trip options.

Trip/Fuel

Trip 1 or Trip 2 - Trip timer, Trip distance, mi to E and avg mpg Fuel Economy

Fuel History

Instant fuel economy AVG MPG mi to E Last 30 minutes AVG MPG mi to E

Average Speed Note: Press and hold OK to reset the currently displayed information. Trip timer Registers the time of individual journeys. Trip distance Registers the mileage of individual journeys. Mi to E Shows the approximate distance your vehicle can travel before running out of fuel. Avg mpg Shows the average fuel usage based on time. Instant fuel economy Shows your instantaneous fuel usage.

Fuel history Shows fuel usage as a bar graph based on time. The graph is updated each minute with the fuel economy that you achieved during 30 minutes of driving. Track Apps

WARNING

Track Apps is for track use only. Remember that even advanced technology cannot defy the laws of physics. It is always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage.

Note: Track Apps are for track use only. They are not to be used under any other driving conditions.

87

Mustang (CZG), enUSA, Third Printing

Information Displays

Note: Viewed or cleared results cannot be used unless your vehicle is at a complete stop. The right arrow on the display menu will be inactive. If your vehicle does not reach 100 mph (160 km/h) during the track run, your display may not display your 1/4
mile results.

Note: The system will disable the collision warning system while using track apps or when you switch off advancetrac.

Accelerometer Acceleration Timer

Brake Performance

Launch Control

Line Lock VIEW/CLEAR Results

Automatic Start or Countdown Start

Track Apps Virtual gauge shown 0-30 MPH (50 km/h) 0-60 MPH (100 km/h) 0-100 MPH (200 km/h) 0-1/8 Mile (200m) 0-1/4 Mile (400m) 60-0 MPH (100km/h) 100-0 MPH (200km/h) Launch Control - check enabled or uncheck disabled RPM

RPM set value

Acceleration Timer Brake Perform All Time Best Clear Saved Data Clear All Time Best

88

Mustang (CZG), enUSA, Third Printing

Information Displays

Accelerometer

Displays your vehicle's rate of acceleration or deceleration. The red dot will move toward the area of acceleration or deceleration. •

LEFT acceleration or deceleration - When accelerating or decelerating left, the red dot will move to the right on the accelerometer.

• RIGHT acceleration/deceleration - When accelerating or decelerating right, the red dot will move to the left on the accelerometer.

Acceleration Timer Displays your vehicle’s rate of acceleration. 1. Choose desired speed or distance.

2. Choose Automatic Start or Countdown

Start.

3. Follow the on-screen prompts. Brake Performance Displays your vehicle’s rate of deceleration. 1. Choose desired speed to start

recording data.

2. Follow the on-screen prompts. Launch Control (if equipped) Maximize traction from a standing start. Line Lock (if equipped) Locks front brakes while allowing rear wheels to turn freely. VIEW/CLEAR Results View and clear the last and saved results of the acceleration timer, brake performance and all time best. Driver Assist Use the arrow buttons to configure different driver setting choices. Note: Some items are optional and may not appear.

Driver Assist Advancetrac - check enabled or uncheck disabled Auto Engine Off – check enabled or uncheck disabled Blindspot - check enabled or uncheck disabled Collision Warning

On - check enabled or uncheck disabled Sensitivity High, Normal or Low

Cross Traffic Alert - check enabled or uncheck disabled Cruise Control

Adaptive or Normal

89

Mustang (CZG), enUSA, Third Printing

E174498Information Displays

Driver Assist

Hill Start Assist - check enabled or uncheck disabled Rear Park Aid - check enabled or uncheck disabled Seatbelt Monitor

On Demand screen pops up

Settings Use the arrow buttons to configure different driver setting choices.

Note: Some items are optional and may not appear.

Settings

Vehicle

Easy Entry/Exit - check enabled or uncheck disabled Lighting

Off or XXX seconds

Locks

Autolamp Delay Daytime Lights - check enabled or uncheck disabled Autounlock - check enabled or uncheck disabled Mislock - check enabled or uncheck disabled Relock - check enabled or uncheck disabled Remote Unlock Switch Inhibit - check enabled or uncheck disabled Hold OK to reset

All Doors or Driver First

Oil Life Reset Park Lock Control - check enabled or uncheck disabled Remote Start

Auto or Last Setting

Climate Control Seats Duration System - check enabled or uncheck disabled 1 - 4 years

Auto or Off 5, 10 or 15 minutes

Remote Open or Close - check enabled or uncheck disabled

90

Tire Mobility Kit Windows

Mustang (CZG), enUSA, Third Printing

Information Displays

Settings

Wipers

MyColor

Gauge Color

Ambient Light

Set MyColor

Courtesy Wipe or Rain Sensing - check enabled or uncheck disabled Ice blue, White, Green, Purple, Blue, Orange, Red or MyColor 1 - 3
Ambient Light - check enabled or uncheck disabled Ambient Dim Ambient Color

High or Low Ice blue, White, Green, Purple, Blue, Orange, Red or MyColor 1 - 3
R, G or B

Set MyColor 1
- 3
X MyKeys, XXX MyKey miles and X Admin Keys

MyKey

Display Setup

Hold OK to Create MyKey

Always On or User Selectable

Always On or User Selectable Always On or User Selectable

MyKey Status Create MyKey 911 Assist Advan- ceTrac Do Not Disturb MAX Speed Speed Minder Volume Limiter - check enabled or uncheck disabled Clear MyKey Distance Temperature Tire Pressure Language

Hold OK to Clear MyKeys Miles & Gallons, L/100km or km/L °Fahrenheit or °Celsius psi or kPa Language 1 - 4 - Hold OK to Set

65, 70, 75, 80 MPH or Off 45, 55 or 65 MPH or Off

91

Mustang (CZG), enUSA, Third Printing

Information Displays

INFORMATION MESSAGES Note: Depending on your vehicle options and instrument cluster type, not all of the messages display or are available. The information display may abbreviate or shorten certain messages.

Press the OK button to acknowledge and remove some messages from the information display. The information display automatically removes other messages after a short time. You need to confirm certain messages before you can access the menus.

Adaptive Cruise Control

Message

Adaptive Cruise

Malfunction

Adaptive Cruise Not

Available

Adaptive Cruise Not

Available Sensor

Blocked See Manual

Normal Cruise Active Automatic Braking

Turned Off

Front Sensor Not Aligned

Action

A radar malfunction is preventing the adaptive cruise control from engaging. See Using Adaptive Cruise Control (page

155).

A condition exists such that the adaptive cruise cannot func- tion properly. See Using Adaptive Cruise Control (page

155).

You have a blocked sensor due to bad weather, ice, mud or water in front of the radar sensor. You can typically clean the sensor to resolve. See Using Adaptive Cruise Control (page

155).

The system has disabled the automatic braking.

A radar malfunction is preventing the adaptive cruise control

from engaging.

92

Mustang (CZG), enUSA, Third Printing

E174595Information Displays

Action

The adaptive cruise has reinstated controls to the driver.

Your vehicle speed is too slow to activate the adaptive cruise.

The adaptive cruise is automatically adjusting the gap

distance and the driver needs to shift the transmission into a

lower gear.

Action

The system detects a malfunction due to a blocked sensor.

The driver has disabled or enabled the traction control.

The system is in sport mode.

Action

The system detects a malfunction due to a blocked sensor.

Remove blockage.

Message

Adaptive Cruise - Driver

Resume Control

Adaptive Cruise Speed Too Low to Activate Adaptive Cruise Shift

Down

AdvanceTrac™ Message

Service AdvanceTrac AdvanceTrac Off On AdvanceTrac SPORT

MODE

Airbag

Message

Occupant Sensor BLOCKED Remove

Objects Near Passenger

Seat

Alarm

Message

Vehicle Alarm to Stop Alarm, Start Vehicle

Alarm All Sensors Peri-

meter Sensing

Action

Alarm triggered due to unauthorized entry. See Anti-Theft

Alarm (page 64).

All perimeter sensors are active. See Anti-Theft Alarm (page

64).

93

Mustang (CZG), enUSA, Third Printing

Information Displays

Battery and Charging System

Message

Check Charging System

Charging System Service

Soon

Charging System Service

Now

Battery State of Charge

Low

Low Battery Features Temporarily Turned Off

Turn Power Off to Save

Battery

Action

The charging system needs servicing. If the warning stays on or continues to come on, contact an authorized dealer as soon

as possible.

The charging system needs servicing. If the warning stays on or continues to come on, contact an authorized dealer as soon

as possible.

The charging system needs servicing. Contact an authorized

dealer as soon as possible.

The battery management system determines that the battery is at a low state of charge. Turn your ignition off as soon as possible to protect the battery. This message clears once you

restart your vehicle and the battery state of charge has

recovered.

The battery management system detects an extended low- voltage condition. Your vehicle disables various features to help preserve the battery. Turn off as many of the electrical loads as soon as possible to improve system voltage. If the system voltage has recovered, the disabled features operate

again as normal.

The battery management system determines that the battery is at a low state of charge. Turn your ignition off as soon as possible to protect the battery. This message clears once you

restart your vehicle and the battery state of charge has recovered. Turning off unnecessary electrical loads allow

faster battery state-of-charge recovery.

94

Mustang (CZG), enUSA, Third Printing

Information Displays

Blind Spot Information and Cross Traffic Alert System

Message

Blindspot System Fault

Blindspot Not Available

Sensor Blocked See

Manual

Action

A fault with the system has occurred. Contact an authorized

dealer as soon as possible.

The system sensors are blocked. See Blind Spot Informa-

tion System (page 162).

Cross Traffic Not Avail- able Sensor Blocked See

Manual

Cross Traffic System

Fault

The blind spot information system and cross traffic alert system sensors are blocked. See Blind Spot Information

System (page 162).

A fault with the system has occurred. Contact an authorized

dealer as soon as possible.

Collision Warning System

Message

Collision Warning

Malfunction

Collision Warning Not

Available Sensor

Blocked See Manual Collision Warning Not

Available

Action

A fault with the system has occurred. Contact an authorized dealer as soon as possible. See Driving Aids (page 162). You have a blocked sensor due to bad weather, ice, mud or water in front of the radar sensor. You can typically clean the

sensor to resolve. See Driving Aids (page 162).

A fault with the system has occurred. Contact an authorized dealer as soon as possible. See Driving Aids (page 162).

Doors and Locks

Message X Door Ajar Trunk ajar Hood Ajar

Switches Inhibited

Security Mode

Action

The door(s) listed is not completely closed.

The trunk is not completely closed. The hood is not completely closed.

The system has disabled the door switches.

95

Mustang (CZG), enUSA, Third Printing

Information Displays

Fuel

Message

Fuel Level Low

Check Fuel Fill Inlet

Hill Start Assist

Message

Action

An early reminder of a low fuel condition.

The fuel fill inlet may not be properly closed.

Action

Hill Start Assist Not

Available

Hill start assist is not available. Contact an authorized dealer.

See Hill Start Assist (page 142).

Keys and Intelligent Access

Message

Action

Press Brake to START

A reminder to press the brake while starting the vehicle.

No Key Detected

The system does not detect a key in your vehicle. See Keyless

Starting (page 122).

Restart Now or Key is

Needed

You pressed the start/stop button to switch off the engine and your vehicle does not detect your intelligent access key

inside your vehicle.

Accessory Power Active Starting System Fault

Key Program Successful

Your vehicle is in the accessory ignition state.

There is a problem with your vehicle’s starting system. See

an authorized dealer for service.

You have successfully programmed an intelligent access key

to the system.

Key Program Failure

Max Number of Keys

Learned

You have failed to program an intelligent access key to the

system.

You have programmed the maximum number of keys to the

system.

96

Mustang (CZG), enUSA, Third Printing

Message

Not Enough Keys

Learned

Key Battery Low Replace

Soon

Engine On

Maintenance Message

LOW Engine Oil Pressure

Change Engine Oil Soon

Oil Change Required Brake Fluid Level LOW

Check Brake System

Transport / Factory

Mode

Information Displays

Action

You have not programmed enough keys to the system.

The key battery is low. Change the battery as soon as possible.

Inform the driver that they are exiting the vehicle and the

engine is on.

Action

Stop your vehicle as soon as safely possible and turn off the engine. Check the oil level. If the warning stays on or continues to come on with your engine running, contact an authorized

dealer as soon as possible.

The engine oil life remaining is 10% or less. See Engine Oil

Check (page 215).

The oil life left is at 0%. See Engine Oil Check (page 215).

The brake fluid level is low, inspected the brake system

immediately. See Brake and Clutch Fluid Check (page 220). The brake system needs servicing. Stop your vehicle in a safe

place. Contact an authorized dealer.

Your vehicle is still in Transport or Factory mode. This may not allow some features to operate properly. See an author-

ized dealer.

See Manual

The powertrain needs service due to a powertrain malfunction.

MyKey

Message

MyKey Not Created MyKey Active Drive

Safely

Speed Limited to XX

MPH/km/h

Mustang (CZG), enUSA, Third Printing

Action

You cannot program a MyKey.

MyKey is active.

When switching on your vehicle and MyKey is in use, displays

that the MyKey speed limit is on.

97

Information Displays

Message

Action

Near Vehicle Top Speed

MyKey is in use and the MyKey speed limit is on and the vehicle

speed is approaching 80 mph (130 km/h).

Vehicle at Top Speed of

MyKey Setting

Check Speed Drive

Safely

Buckle Up to Unmute

Audio

AdvanceTrac On -

MyKey Setting

Traction Control On -

MyKey Setting

MyKey Park Aid Cannot

be Deactivated

Park Aid

Message

Check Rear Park Aid

You have reached the speed limit set for your MyKey.

You have an active MyKey with a programmed set speed limit.

Belt-Minder turns on with a MyKey in use.

With a MyKey in use, AdvanceTrac turns on.

With a MyKey in use, traction control turns on.

With a MyKey in use, park aid is always on.

Action

The system has detected a condition that requires service. Contact an authorized dealer. See Parking Aid (page 149).

Rear Park Aid On Off

Displays the park aid status.

Park Brake

Message

Park Brake Engaged

Remote Start Message

Action

You have set the parking brake and you have driven the vehicle more than 3 mph (5 km/h). If the warning stays on after you have released the parking brake, contact an authorized dealer.

Action

To Drive: Press Brake

and Start Button

A reminder to apply the brake and push the start button to

drive your vehicle after a remote start.

98

Mustang (CZG), enUSA, Third Printing

Information Displays

Seats

Message

Memory Recall Not

Permitted While Driving

A reminder that memory seats are not available while driving.

Action

Memory X Saved

Shows where you have saved your memory setting.

Starting System

Message

Press Brake to Start Press Clutch to Start

Cranking Time Exceeded

Engine Start Pending

Please Wait

Action

A reminder to apply the brake when starting your vehicle. A reminder to apply the clutch when starting your vehicle. The starter has exceeded its cranking time in attempting to

start your vehicle.

The starter is attempting to start your vehicle.

Pending Start Cancelled

The system has cancelled the pending start.

Steering System

Message

Action

Steering Fault Service

Now

The power steering system has detected a condition that

requires service. See an authorized dealer.

Steering Loss Stop

Safely

The power steering system is not working. Stop your vehicle

in a safe place. Contact an authorized dealer.

Steering Assist Fault

Service Required

Steering Lock Malfunc-

tion Service Now

Steering Col. Lock Turn Wheel while Starting

vehicle

The power steering system has detected a condition within the power steering system or passive entry or passive start

system requires service. Contact an authorized dealer. The steering lock system has detected a condition that

requires service. See an authorized dealer.

You need to turn your steering wheel while start your vehicle

to unlock your steering column.

99

Mustang (CZG), enUSA, Third Printing

Information Displays

Tire Pressure Monitoring System

Message

Tire Pressure LOW

Tire Pressure Monitor

Fault

Tire Pressure Sensor

Fault

Traction Control

Message

Traction Control Off / Traction Control On Spinout Detected Hazards Activated

Transmission Message

Transmission Malfunc-

tion Service Now Transmission Over- heating Stop Safely

Transmission Overtem- perature Stop Safely Transmission Service

Required

Transmission Too Hot

Press Brake

Action

One or more tires on your vehicle has low tire pressure. See

Tire Pressure Monitoring System (page 258).

The tire pressure monitoring system is malfunctioning. If the authorized dealer. See Tire Pressure Monitoring System

warning stays on or continues to come on, contact an

(page 258).

A tire pressure sensor is malfunctioning or your spare tire is in use. See Tire Pressure Monitoring System (page 258). If the warning stays on or continues to come on, contact an

authorized dealer as soon as possible.

Action

The status of the traction control system after you switched

it off or on. See Using Traction Control (page 144).

A spinout has occurred and the hazards are on.

Action

See your authorized dealer.

The transmission is overheating and needs to cool. Stop in a

safe place as soon as it is possible.

The transmission has overheated and needs to cool. Stop in

a safe place as soon as it is possible.

See your authorized dealer.

Transmission is getting hot. Stop to let it cool.

100

Mustang (CZG), enUSA, Third Printing

Information Displays

Action

Displays when the transmission has overheated and has

limited functionality. See Automatic Transmission (page

137).

Transmission is too cold. Wait for it to warm up before you

drive.

Displays as a reminder to shift into park.

Displays as a reminder to press the brake pedal in order to

select a gear.

Displays when the transmission has adjusted the shift

strategy.

Displays when the transmission is adjusting the shift strategy.

Displays when the transmission shift lever is locked and unable

to select gears.

Displays when the transmission shift lever is unlocked and

free to select gears.

Message

Transmission Limited Function See Manual

Transmission Warming

Up Please Wait

Transmission Not in Park

Press Brake Pedal

Transmission Adjusted

Transmission Adapt

Mode

Transmission Indicate

Mode Lockup On

Transmission Indicate

Mode Lockup Off

101

Mustang (CZG), enUSA, Third Printing

Climate Control

MANUAL CLIMATE CONTROL (If Equipped)

Power: Press the button to switch the system on and off. When the system is off, it prevents outside air from entering the vehicle. Defrost: Select to distribute air through the windshield air vents. Air distribution to the instrument panel and footwell vents turns off. You can also use this setting to defrost and clear the windshield of a thin covering of ice. Heated rear window: Press the button to switch the heated rear window on and off. See Heated Windows and Mirrors (page 107). MAX A/C: Adjust the control to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. Temperature control: Controls the temperature of the air circulated in your vehicle. MAX Defrost: Adjust the control to switch on defrost. Outside air flows through the windshield vents, air conditioning automatically turns on, and fan automatically adjusts to the highest speed. You can also use this setting to defrost and clear the windshield of a thin covering of ice. The heated rear window also automatically turns on when you select maximum defrost. Note: To prevent window fogging, you cannot select recirculated air when maximum defrost is on.

102

Mustang (CZG), enUSA, Third Printing

E174095Climate Control

Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle. Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. Air distribution control: Adjust the control to turn airflow from the windshield, instrument panel, or footwell vents on or off. You can distribute air through any combination of these vents. A/C: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air. To improve the time to reach a comfortable temperature in hot weather, drive with the windows open until you feel cold air through the air vents. Note: In certain conditions (for example, maximum defrost), the air conditioning compressor may continue to operate even though the air conditioning is switched off. Fan speed indicators: Illuminates to indicate fan speed. Fan speed control: Adjusts the volume of air circulated in the vehicle.

AUTOMATIC CLIMATE CONTROL (If Equipped)

103

Mustang (CZG), enUSA, Third Printing

E174096Climate Control

Heated seats (if equipped): Press the button to switch the heated seats on and off. See Climate Controlled Seats (page 114). Driver temperature control: Adjusts the temperature setting using the control on the driver side. Defrost: Select to distribute air through the windshield air vents. Air distribution to the instrument panel and footwell vents turns off. You can also use this setting to defrost and clear the windshield of a thin covering of ice. MAX Defrost: Press the button to switch on defrost. Outside air flows through the windshield vents, air conditioning automatically turns on, and fan automatically adjusts to the highest speed. You can also use this setting to defrost and clear the windshield of a thin covering of ice. The heated rear window also automatically turns on when you select maximum defrost. Note: To prevent window fogging, you cannot select recirculated air when maximum defrost is on. Fan speed control: Adjusts the volume of air circulated in the vehicle. Power: Press the button to switch the system on and off. When the system is off, it prevents outside air from entering the vehicle. MAX A/C: Press the button to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. Note: In certain conditions (for example, maximum defrost), the air conditioning compressor may continue to operate even though the air conditioning is switched off. Passenger temperature control: Adjusts the temperature on the passenger side. Climate controlled seats (if equipped): Press the button to switch the climate controlled seats on and off. See Climate Controlled Seats (page 114). AUTO: Press the button to turn on automatic operation. Select the desired temperature using the temperature control. The system adjusts fan speed, air distribution, air conditioning operation, and selects outside air or recirculated air to heat or cool the vehicle in order to maintain the desired temperature. You can also use the AUTO button to turn off dual zone operation by pressing and holding the button for more than two seconds. Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle.

104

Mustang (CZG), enUSA, Third Printing

Climate Control

Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. Heated rear window: Press the button to switch the heated rear window on and off. See Heated Windows and Mirrors (page 107).

HINTS ON CONTROLLING THE INTERIOR CLIMATE General Hints Note: Prolonged use of recirculated air may cause the windows to fog up. Note: You may feel a small amount of air from the footwell air vents regardless of the air distribution setting. Note: To reduce humidity build-up inside your vehicle, do not drive with the system switched off or with recirculated air always switched on. Note: Do not place objects under the front seats as this may interfere with the airflow to the rear seats. Note: Remove any snow, ice or leaves from the air intake area at the base of the windshield. Note: To improve the time to reach comfort in hot weather, drive with the windows fully open until you feel cold air through the air vents.

Manual Climate Control Note: To reduce fogging of the windshield during humid weather, adjust the air distribution control to the windshield air vents position. Automatic Climate Control Note: Adjusting the settings when your vehicle interior is extremely hot or cold is not necessary. The system automatically adjusts to heat or cool the cabin to your selected temperature as quickly as possible. For the system to function efficiently, the instrument panel and side air vents should be fully open. Note: If you select AUTO during cold outside temperatures, the system directs airflow to the windshield and side window vents. In addition, the fan may run at a slower speed until the engine warms up. Note: If you select AUTO during hot outside temperatures, or when the inside of the vehicle is hot, the system automatically uses recirculated air to maximize interior cooling. When the interior reaches the selected temperature, the system automatically switches to using outside air.

105

Mustang (CZG), enUSA, Third Printing

Climate Control

Heating the Interior Quickly

Vehicle with manual climate control Adjust the fan speed to a high speed setting. Adjust the temperature control to the highest setting. Select the footwell air vents using the air distribution buttons.

Recommended Settings for Heating Vehicle with manual climate control

Adjust the fan speed to the center setting. Adjust the temperature control to the midway point of the hot settings.

Select the footwell air vents using the air distribution buttons.

Cooling the Interior Quickly

Vehicle with manual climate control Adjust the temperature control to the MAX A/C position. Drive with the windows fully open until you feel cold air through the air vents.

Vehicle with automatic climate control Press the AUTO button.

Adjust the temperature control to the desired setting.

Vehicle with automatic climate control Press the AUTO button.

Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

Vehicle with automatic climate control Press the MAX A/C button.

106

Mustang (CZG), enUSA, Third Printing

Climate Control

Recommended Settings for Cooling Vehicle with manual climate control

Adjust the fan speed to the center setting. Adjust the temperature control to the midway point of the cold settings.

Select the instrument panel air vents using the air distribution buttons.

Vehicle with automatic climate control Press the AUTO button.

Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

Side Window Defogging in Cold Weather

Vehicle with manual climate control

Select the windshield air vents using the air distribution buttons. Press the A/C button.

Vehicle with automatic climate control Press the defrost button.

Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

Adjust the temperature control to the desired setting. Adjust the fan speed to the highest setting.

HEATED WINDOWS AND MIRRORS (If Equipped) Heated Rear Window Note: Make sure the engine is running before operating the heated windows. Press the button to clear the heated rear window of thin ice and fog. The heated rear window