2015 Ford F 250 Owners Manual

either side of each map lamp to turn on the lamps. The map lamps also light when:

69

Super Duty (), enUSA

E163271AE163272Lighting

• •

•

any door is opened. the instrument panel dimmer switch is pressed up until the courtesy lamps come on. any of the remote entry controls are pressed and the ignition is off.

Rear Dome and Map Lamps

Your vehicle may have map lamps within the rear dome lamp. Press the switches on either side of the dome lamp to turn the lamps on.

70

Super Duty (), enUSA

E163273E163274Windows and Mirrors

Note: Perform one-touch up re-calibration with the door closed. Calibrating with the door open will cause the window to continuously bounce back. To reset the function after the battery recharges: 1. Pull the switch all the way up. 2. Hold the switch until the glass stops

and continue to hold for two seconds. 3. Press the switch down and operate the

window to the full down position. One-touch up will now be functional.

Bounce-Back (If Equipped) The window will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature

WARNING

When you override the bounce-back feature, the window will not reverse if it detects an obstacle. Take care

when closing the windows to avoid personal injury or damage to your vehicle.

Pull up the window switch and hold within two seconds of the window reaching the bounce-back position. The window will travel up with no bounce-back protection. The window will stop if you release the switch before the window closes fully.

POWER WINDOWS (If Equipped)

WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

children and pets are not in the proximity of the window openings.

Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise. Press the switch to open the window. Lift the switch to close the window. One-Touch Up or Down (If Equipped) Press or lift the switch fully and release it. Press or lift it again to stop the window. Note: The window may disable for up to five minutes if you cycle it up and down repeatedly. This helps prevent damage to the motor. Normal operation will resume once the motor cools. Restoring the One-Touch Up Function You may lose the one-touch function if the vehicle battery is low.

71

Super Duty (), enUSA

E163056Windows and Mirrors

Window Lock (If Equipped)

Unlock Lock

Press the control to lock or unlock the rear window controls. Power Sliding Back Window (If Equipped)

WARNINGS

When operating the power sliding back window, you must make sure all rear seat occupants and cargo are

not in the proximity of the back window. Do not leave children unattended in your vehicle and do not let them play with the power sliding back window.

They may seriously injure themselves.

Press and hold the control to open the window. Pull and hold the control to close the window. Accessory Delay (If Equipped) You can use the window switches for several minutes after you switch the ignition off or until you open either front door. GLOBAL OPENING (If Equipped) You can use the remote control to operate the windows with the ignition off. Note: To operate this feature, accessory delay must not be active. Opening the Windows You can only open the windows for a short time after you unlock your vehicle with the remote control. After you unlock your vehicle, press and hold the remote control unlock button to open the windows. Release the button once movement starts. Press the lock or unlock button to stop movement. EXTERIOR MIRRORS Power Exterior Mirrors (If Equipped)

WARNING

Do not adjust the mirrors when your vehicle is moving.

The control is on the overhead console.

72

Super Duty (), enUSA

E163057ABE163058Windows and Mirrors

Note: If you repeatedly fold and unfold the mirrors several times within one minute, the system may disable to protect the motors from overheating. It will reset to normal function automatically within three to five minutes. You can also fold a mirror manually by pushing it toward the door window glass. After you manually adjust the mirror, you will need to reset it. To reset the power-folding mirror system and return it to its normal function: •

Fold the mirror manually by pushing it toward the door window glass.

• Use the power-fold control to fold and

unfold the mirror two or three times. The mirror will make a sound as it resets.

Heated Exterior Mirrors (If Equipped) See Heated Windows and Mirrors (page 111). Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memory function. See Memory Function (page 116). Clearance Lamps (If Equipped) The lower, outer part of the mirror housings light when you switch the headlamps or parking lamps on.

Left-hand mirror Off Right-hand mirror

To adjust a mirror: 1. Rotate the control to select the mirror

you want to adjust.

2. Adjust the position of the mirror. 3. Return the control to the center position to lock mirrors in place. Fold-Away Exterior Mirrors For tight parking conditions, you can push the mirror toward the door window glass. Before driving, make sure that you fully engage the mirror in its support when returning it to its original position. Power-Folding Mirrors (If Equipped)

1. Rotate the control so the dots line up. 2. Pull the control back to fold the mirrors

in or out.

73

Super Duty (), enUSA

E163059BACE163060Windows and Mirrors

Telescoping Mirrors (If Equipped)

This feature lets you extend the mirror about 3 inches (75 millimeters). It is useful when towing a trailer. You can manually pull out or push in the mirrors to the desired position. PowerScope™ Power Telescoping Mirrors (If Equipped) This feature lets you position both mirrors in or out at the same time. The control is on the door trim panel.

Telescope Out Telescope In

To adjust the mirrors: • Press and hold the control. • When you position the mirrors in or out, the motors will run as long as you hold the control. The running motors allow you to make adjustments as needed. • After positioning the mirrors, return the

control to the center position to help protect the motors from overheating.

INTERIOR MIRROR WARNING

Do not adjust the mirror when your vehicle is moving.

Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up.

74

Super Duty (), enUSA

E163061E163062BAWindows and Mirrors

WARNINGS

When closing the moonroof, you should verify that it is free of obstructions and make sure that

children and pets are not in the proximity of the roof opening.

You can manually open or close the sliding shade when the moonroof is closed. Pull the shade toward the front of your vehicle to close it. The moonroof controls are located on the overhead console and have a one-touch open and close feature. To stop it during one-touch operation, press the control a second time. Opening and Closing the Moonroof

Press and release the SLIDE control to open the moonroof. The moonroof will stop short of the fully opened position. Note: This position helps to reduce wind noise or rumbling which may happen with the moonroof fully open. Press and release the control again to fully open the moonroof. Pull and release the SLIDE control to close the moonroof.

SUN VISORS Slide-on-rod (If Equipped)

Rotate the sun visor toward the side window and extend it rearward for extra shade. Illuminated Vanity Mirror (If Equipped)

Lift the cover to switch the lamp on. MOONROOF (If Equipped) WARNINGS

Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously

hurt themselves.

75

Super Duty (), enUSA

E138666E162197E163063Windows and Mirrors

Bounce-Back The moonroof will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Pull and hold the SLIDE control within two seconds of a bounce-back event to override this function. While bounce-back is active, the closing force increases for each of the next three times that you close the moonroof. Venting the Moonroof Press and release the TILT control to vent the moonroof. Pull and hold the TILT control to close the moonroof.

76

Super Duty (), enUSA

Instrument Cluster

GAUGES

Engine oil pressure gauge Engine coolant temperature gauge Transmission fluid temperature gauge Fuel gauge Speedometer Information display See (page 84). Tachometer

77

Super Duty (), enUSA

ABCDGFEE163168Instrument Cluster

transmission for extended periods of time with the gauge in the higher than normal area may cause internal transmission damage. Altering the severity of the driving conditions is recommended to lower the transmission temperature into the normal range. If the gauge continues to show high temperatures, see your authorized dealer. Fuel Gauge Note: The fuel gauge may vary slightly when your vehicle is moving or on a gradient. Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located. The needle should move toward F when you refuel your vehicle. If the needle points to E after adding fuel, this indicates your vehicle needs service soon. After refueling some variability in needle position is normal: •

It may take a short time for the needle to reach F after leaving the gas station. This is normal and depends upon the slope of pavement at the gas station. The fuel amount dispensed into the tank is a little less or more than the gauge indicated. This is normal and depends upon the slope of pavement at the gas station. If the gas station nozzle shuts off before the tank is full, try a different gas pump nozzle. Low Fuel Reminder A low fuel reminder triggers when the fuel gauge needle is at 1/16th.

•

•

Engine Oil Pressure Gauge Indicates engine oil pressure. The needle should stay in the normal operating range (between L and H). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked by your authorized dealer. Engine Coolant Temperature Gauge

WARNING

Never remove the coolant reservoir cap while the engine is running or hot.

Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Transmission Fluid Temperature Gauge Indicates transmission fluid temperature. At normal operating temperature, the level indicator will be in the normal range. If the transmission fluid temperature exceeds the normal range, stop the vehicle as soon as safely possible and verify the airflow is not restricted such as snow or debris blocking airflow through the grill. Also, higher than normal operating temperature can be caused by special operation conditions (i.e. snowplowing, towing or off-road use). Refer to Special operating conditions in the scheduled maintenance information for instructions. Operating the

78

Super Duty (), enUSA

Instrument Cluster

Variations:

Driving type (fuel economy

conditions)

Highway driving

Severe duty driving (trailer

towing, extended idle)

Fuel gauge position

Distance-to-empty

1/16th

1/16th

35 miles to 80 miles (56 km

to 129 km)

35 miles (56km)

Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled. Trip Computer See (page 84). Vehicle Settings and Personalization See (page 84). WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information. Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle.

Anti-Lock Braking System

If it illuminates when you are driving, this indicates a malfunction. You will continue

to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer. Battery

If it illuminates while driving, it indicates a malfunction. Switch off all unnecessary electrical

equipment and have the system checked by your authorized dealer immediately. Brake System

Illuminates when you engage the parking brake with the ignition on.

If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.

79

Super Duty (), enUSA

E144522Instrument Cluster

WARNING

Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Check Fuel Cap (If Equipped)

Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service engine

soon warning indicator to come on. Cruise Control (If Equipped)

Illuminates when you switch this feature on. See Using Cruise Control (page 178).

Direction Indicator

Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the

indicators stay on or flash faster, check for a burned out bulb. Door Ajar

Displays when the ignition is on and any door is not completely closed.

Electronic Locking Differential Illuminates when using the electronic locking differential.

Engine Coolant Temperature

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as

possible, switch off the engine and let cool. Engine Oil

If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 235). Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by your authorized dealer immediately. Fasten Safety Belt

It will illuminate and a chime will sound to remind you to fasten your safety belt.

Front Airbag

If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer. High Beam

Illuminates when you switch the high beam headlamps on. It will flash when you use the

headlamp flasher. Hill Descent (If Equipped)

Illuminates when hill descent is switched on.

80

Super Duty (), enUSA

E71340E163170E163171Instrument Cluster

If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

WARNING

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic

converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Have an authorized dealer service your vehicle immediately.

The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 144). Stability Control

Illuminates when the system is active. If it remains illuminated or does not illuminate when you

switch the ignition on, this indicates a malfunction. During a malfunction the system will switch off. Have the system checked by your authorized dealer immediately. See Using Stability Control (page 169).

Low Fuel Level

Illuminates when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as

possible. Low Tire Pressure Warning

Illuminates when your tire pressure is low. If the lamp remains on with the engine running or when driving, check

your tire pressure as soon as possible. It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by your authorized dealer. Powertrain Malfunction/Reduced Power/Electronic Throttle Control Illuminates when a powertrain or an AWD fault has been detected. Contact your

authorized dealer as soon as possible. Service Engine Soon

If the service engine soon indicator light stays illuminated after the engine is started, it

indicates that the On-Board Diagnostics (OBD-II) system has detected a malfunction of the vehicle emissions control system. Refer to On-Board Diagnostics (OBD-II) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 144).

81

Super Duty (), enUSA

E138639Instrument Cluster

Stability Control Off

Illuminates when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off. See Using Stability Control (page 169). Transmission Tow/Haul (If Equipped) Illuminates when the tow/haul feature has been activated. If the light flashes steadily, have the system serviced immediately, damage to the transmission could occur. 4X2 (If Equipped)

Illuminates momentarily when two-wheel drive high is selected. If the light fails to display when

the ignition is turned on, or remains on, have the system serviced immediately by your authorized dealer. 4X4 LOW (If Equipped)

Illuminates when four-wheel drive low is engaged. If the light fails to display when the ignition

is turned on, or remains on, have the system serviced immediately by your authorized dealer. 4X4 HIGH (If Equipped)

Illuminates when four-wheel drive high is engaged. If the light fails to display when the ignition

is turned on, or remains on, have the system serviced immediately by your authorized dealer.

Diesel Warning Lights If your vehicle is equipped with a diesel engine, it has some unique warning lights; refer to your diesel supplement for detailed information on their function. Diesel engine brake

For more information see your diesel supplement.

Diesel exhaust fluid

For more information see your diesel supplement.

Glow plug pre-heat

For more information see your diesel supplement.

Water in fuel

For more information see your diesel supplement.

AUDIBLE WARNINGS AND INDICATORS Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position.

82

Super Duty (), enUSA

E161509E163173E163174E163175E171217E163176Instrument Cluster

Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately.

83

Super Duty (), enUSA

Information Displays

Information Display Controls (Type 1)

GENERAL INFORMATION

WARNING

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

You can control various systems on your vehicle using the information display controls on the steering wheel. The information display provides the corresponding information.

• Press the INFO button to scroll through trip, outside temperature, fuel usage, trailer gain and MyKey® information.

• Press the SETUP button to scroll

through various vehicle feature settings.

• Press the RESET button to choose

settings, reset information and confirm messages.

Info Press the INFO button repeatedly to cycle through the following features: Note: Some options may appear slightly different or not at all if the items are optional.

84

Super Duty (), enUSA

E163177Information Displays

INFO

TRIP A/B XXX° (if equipped) MYKEY MILES (km) (if programmed) XXX MILES (km) TO E XX.X AVG MPG (L/100km) MPG (L/km) TIMER TBC GAIN (if equipped) EXHAUST FILTER (diesel only)

TRIP A/B Registers the distance of individual journeys. Press and release the INFO button until TRIP A/B appears in the display (this represents the trip mode). Press and hold the RESET button to reset. XXX° (outside air temperature) This displays the outside temperature. MYKEY MILES (km) For more information, See Principle of Operation (page 51). XXX MILES (km) TO E This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to detect the correct amount of added fuel. The system calculates the distance to empty by using a running average fuel economy, which uses your recent driving history of 500 miles (800 km).

85

Super Duty (), enUSA

This value is not the same as the average fuel economy display. The running average fuel economy resets to a factory default value if the battery is disconnected. XX.X AVG MPG (L/100km) Average fuel economy displays your average fuel economy in miles per gallon or liters/100 km. MPG (L/km) Displays the instantaneous fuel economy as a bar graph. Your vehicle must be moving to calculate instantaneous fuel economy. You cannot reset the instantaneous fuel economy. TIMER Displays the trip elapsed drive time. Press and release RESET to pause the timer. Press and hold RESET to reset the timer. TBC GAIN Displays the level of trailer brake gain or if the trailer is not connected.

Information Displays

EXHAUST FILTER For more information, refer to the Diesel supplement. System check and vehicle feature customization Press the SETUP button repeatedly to cycle the information display through the following features:

Note: Some options may appear slightly different or not at all if the items are optional. Note: When returning to the SETUP menu and you selected a non-English language, HOLD RESET FOR ENGLISH will display to change back to English. Press and hold the RESET button to change back to English.

RESET FOR SYSTEM CHECK

SETUP

press the RESET button

OIL LIFE EXHAUST FLUID LEVEL (Diesel only) ENGINE HOURS ENGINE IDLE HOURS CHARGING SYSTEM DOOR BRAKE SYSTEM TBC GAIN = XX.X FUEL LEVEL MYKEY DISTANCE

SETUP (cont’d)

RESET FOR SYSTEM CHECK

press the RESET button

MYKEY(S) PROGRAMMED ADMIN KEYS PROGRAMMED

press the RESET button

OIL LIFE UNITS AUTOLAMP (SEC) AUTOLOCK AUTOUNLOCK COURTESY WIPE

English or Metric 0 to 180 seconds On or Off On or Off On or Off

86

Super Duty (), enUSA

Information Displays

SETUP (cont’d) On or Off

REMOTE WINDOW OPEN CREATE MYKEY / MYKEY SETUP / CLEAR MYKEY RESET FOR REMOTE START

press the RESET button

On or Off 5, 10, 15 minutes Electric or EOH LOW, MED or HIGH On or Off English / Spanish / French

3. Once OIL LIFE SET TO XXX% is

displayed, release and press the RESET button to change the Oil Life Start Value. Each release and press will reduce the value by 10%.

UNITS Displays the current units English or Metric AUTOLAMP (SEC) This feature keeps your headlights on for up to three minutes after the ignition is switched off. AUTOLOCK This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. AUTOUNLOCK This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off.

TBC MODE TBC EFFORT TRAILER SWAY LANGUAGE = ENGLISH / SPANISH / FRENCH

PRESS RESET FOR SYSTEM CHECK The information display will begin to cycle through the vehicle systems and provide a status of the item if needed. Note: Some systems show a message only if a condition is present OIL LIFE Displays the remaining oil life. An oil change is required whenever indicated by the information display and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change, perform the following: 1. Press and release the SETUP button

to display OIL LIFE XXX% HOLD RESET = NEW.

2. Press and hold the RESET button for two seconds and release to reset the oil life to 100%.

Note: To change oil life 100% value (if equipped with this feature) to another value, proceed to Step 3.

87

Super Duty (), enUSA

Information Displays

Information Display Controls (Type 2) (If Equipped)

• Press the up and down arrow buttons

to scroll through and highlight the options within a menu.

• Press the right arrow button to enter a

sub-menu.

• Press the left arrow button to exit a

menu.

• Press the OK button to choose and

confirm a setting/messages.

Main menu You can access the menus using the information display control.

Gauge Mode

COURTESY WIPE This feature allows for an extra swipe of the wipers after a wipe/wash cycle. CREATE MYKEY / MYKEY SETUP / CLEAR MYKEY For more information, See Creating a MyKey (page 51). RESET FOR REMOTE START (if equipped) REAR PARK AID This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected. TBC MODE (if equipped) Allows you to choose the trailer brake mode. TBC EFFORT (if equipped) Allows you to choose the level of initial braking. TRAILER SWAY (if equipped) This feature uses the electronic stability control to mitigate trailer sway. LANGUAGE = ENGLISH / SPANISH / FRENCH Allows you to choose which language the message center will display in. Waiting four seconds or pressing the RESET button cycles the message center through each of the language choices. Press the RESET button to set the language choice.

88

Super Duty (), enUSA

E163178E163179Information Displays

Trip A / B

Fuel Economy

Settings

Information

Truck Apps (If Equipped)

Display Mode

Gauges Detail

Use the arrow buttons to choose between the following gauge options.

Gauge Mode

Engine Oil Temperature (Diesel only) Transmission Temperature Compass

The compass orientation can be changed between fixed north or rotating north. To change the modes, press OK when the compass display is shown. Use the right arrow to choose the mode. Press and hold OK to set the mode.

Exhaust Filter (diesel only). Refer to your diesel supple- ment for more information. Blank

Trip A / B

Use the arrow buttons to choose between the following trip options.

89

Super Duty (), enUSA

E138660E163180E163181E144641E144642E163179E138660Information Displays

Trip A / B

Trip time Trip distance Fuel used Avg MPG (L/100km) Odometer

Press OK to pause the Trip A or B screen, press again to un-pause. Press and hold OK to reset the currently displayed trip information. Trip time This shows the elapsed trip time. The timer will stop when your vehicle is turned off and will restart when your vehicle is restarted. Trip distance Registers the mileage of individual journeys.

Fuel used Shows the amount of fuel used for a given trip. Average MPG Shows the average distance traveled per unit of fuel used for a given trip. Fuel Economy

Use the arrow buttons to choose the desired fuel economy display.

Fuel Econ.

Fuel Hist.

Fuel Economy

Instant MPG (L/100km) Miles (kilometers) to Empty AVG MPG (L/100km) 5, 10, 30 Minutes or Last 5 Resets

Average MPG Shows the average fuel usage based on time. Press and hold OK to reset this value.

Instant MPG Shows your instantaneous fuel usage. Miles to empty Shows the approximate distance your vehicle can travel before running out of fuel.

90

Super Duty (), enUSA

E163180Information Displays

Fuel Hist. Shows fuel usage as a bar graph based on time. The graph is updated each minute with the fuel economy that was achieved during the prior 5, 10, 30 minutes of driving.

Truck Apps

In this mode, off-road information depicted with graphics and trailer towing

application options are available. Note: Some items are optional and may not appear.

Truck Apps

Off Road

Trailer

Pitch and bank angle (in degrees) Steering angle (in degrees) Differential lock/unlock Energy flow Press OK for Info

ELD (Electronic Locking Differential) Hill Descent Control 4X4 System Traction Control AdvanceTrac + RSC

Active trailer name or default trailer Accumulated trailer distance Trailer gain and output Trailer Disconnected Press OK for options

Options Change Active Trailer Adding a new trailer Connection Checklist (if equipped) Delete Trailer Information Screen

Conventional, Fifth Wheel or Gooseneck

Tow / Haul or Trailer Brake Controller

91

Super Duty (), enUSA

E163181Information Displays

Truck Apps (cont’d)

Trailer (cont’d)

Press OK for options

Trailer disconnected Disregard this status if your vehicle is not equipped with a factory installed trailer brake controller. This message may appear when an aftermarket TBC is used even when the trailer is connected. Change Active Trailer When this is highlighted, press the right arrow key to change the currently selected trailer. Use the up and down arrows to select a trailer and press the OK button to choose the highlighted trailer. Adding a new trailer Use the up/down arrows to highlight New Trailer and press the right arrow key to enter the New Trailer input screen. Use the up/down arrow keys to choose alpha, numeric and symbol characters and then press the right arrow to move the character space over. Continue adding characters as needed. Press the left arrow to go back and change a previously selected character. When finished with the new trailer name, press OK to accept the new trailer name.

Rename Trailer Reset Trailer Mileage / Kilometers (if equipped)

Connection Checklist Use the up/down arrows to highlight one of these choices and press OK to display the connection checklist. Follow the on-screen instructions to go through the connections list. Delete Trailer Use the up/down arrows to highlight the trailer you want to delete and press OK to delete. Follow the on-screen prompts to exit or confirm delete. Rename Trailer Use the up/down buttons to highlight a trailer and press OK to select it. Use the up/down arrow buttons to change the characters as needed. When done, press OK to accept the change. Reset Trailer Mileage / Kilometers Use the up/down buttons to select a trailer, then press and hold OK to reset the trailer mileage (kilometers). Settings

Use the arrow buttons to configure different driver setting choices.

Note: Some items are optional and may not appear.

92

Super Duty (), enUSA

E144641Information Displays

Driver Assist

Rear Park Aid Rear Video Camera Trailer Brake

Vehicle

Trailer Sway Control Autolamp Delay DTE Calculation (distance to empty)

Easy Entry/Exit Locks

Settings On or Off Camera Delay Mode

Effort On or Off Off or XXX seconds Normal Towing On or Off Autolock Autounlock Unlocking

Maintenance

Coolant (if equipped)

Fuel Filter (diesel only)

On or Off Electric or Elect. Over Hydraulic Light, Medium or Heavy

On or Off On or Off One Stage or Two Stage Hold OK if Coolant Changed Hold OK if Fuel Filter Changed

Vehicle (cont’d)

Menu Control Oil Life Reset Remote Start

Windows Wiper Control

Settings (cont’d)

Standard or Memory On Set to XXX% (Hold OK to Reset) Duration System Remote Open Courtesy Wipe - On or Off

5, 10 or 15 minutes Enable or Disable On or Off

93

Super Duty (), enUSA

Information Displays

Settings (cont’d)

Hold OK to Create MyKey Always On or Selectable 80 MPH (130 km/h) or Off 45, 55 or 65 MPH (75, 90 or 105 km/h), Off On or Off Hold OK to Clear MyKey

English Metric Fahrenheit (°F) Celsius (°C)

MyKey

Language Units

Create MyKey AdvanceTrac MAX Speed Speed Warning Volume Limiter Clear MyKey English, Français, Español Distance

Temperature

Information

In this mode, you can view different vehicle system information and perform a

system check.

MyKey

System Check

Information

Admin Keys (Number of admin keys) MyKeys (Number of MyKeys programmed) MyKey Miles (km) (Distance traveled using a programmed MyKey) Some items will only display during a system check if a problem has been detected. If an issue exists on one of the monitored systems, the number of warnings that need immediate attention will display in red and the number of informational warnings will display in amber. Use the up/ down arrow buttons to scroll through the list; press the right arrow button to display specific information on the highlighted warning

94

Super Duty (), enUSA

E144642Information Displays

Compass/Transmission indicator display (if equipped) The compass heading will display in the upper right corner of the information display; the transmission gear indicator displays in the right side of the information display when using the SelectShift Automatic™ transmission feature. These displays will not be shown in all screen modes. For example: when programming certain vehicle features or in certain information menus.

INFORMATION MESSAGES Note: Depending on your vehicle options and instrument cluster type, not all of the messages will display or be available. Additionally, the information display may abbreviate or shorten certain messages. Press the RESET button for Type 1 displays or the OK button for Type 2 displays to acknowledge and remove some messages from the information display. The information display will automatically remove other messages after a short time. You need to confirm certain messages before you can access the menus.

AdvanceTrac™ Message

Action

SERVICE ADVAN-

CETRAC

The system detects a condition that requires service. Have

the system checked by an authorized dealer.

ADVANCETRAC OFF

The driver has disabled the stability control system. See

Using Stability Control (page 169).

TRACTION CONTROL

OFF

The driver has disabled the traction control system. See Using

Traction Control (page 167).

Alarm

Message

TO STOP ALARM START VEHICLE

SECURITY SYSTEM

FAULT

Action

An unauthorized entry has triggered the alarm. See Anti-Theft

Alarm (page 61).

The security system has detected a fault. Have the system

checked by an authorized dealer.

95

Super Duty (), enUSA

Information Displays

Diesel Messages

WARNING

When the CLEANING EXHAUST FILTER message appears in the information display, do not park near flammable materials, vapors or structures until filter cleaning is complete.

Message

Action

CHECK COOLANT

ADDITIVE

The coolant additive needs checking. Refer to your diesel

supplement for more information.

CLEANING EXHAUST

FILTER

Your vehicle has entered the cleaning mode. Various engine

actions will raise the exhaust temperature in the Diesel Particulate Filter system to burn off the particles (exhaust soot). After the vehicle burns the particles off the exhaust temperature will return to normal levels. This message is

NORMAL. Refer to your diesel supplement for more informa-

tion.

EXHAUST OVER- LOADED DRIVE TO

CLEAN

EXHAUST AT LIMIT

DRIVE TO CLEAN NOW

The diesel particulate filter is full of particles (exhaust soot) and you are not operating the vehicle in a manner that allows normal cleaning. One of these messages will stay on until the exhaust filter cleaning has begun, at which time the CLEANING

EXHAUST FILTER message displays. We recommend you

drive the vehicle above 30 mph (48 km/h) until the CLEANING

EXHAUST FILTER message turns off. Refer to your diesel

supplement for more information.

The diesel particulate filter will continue to fill with particles (exhaust soot) if you ignore this message. The service engine soon light will illuminate and engine power may be limited, if cleaning is not permitted. Dealer service will then be required

to restore your vehicle to full-power operation.

STOP SAFELY NOW

ENGINE OIL DILUTED

Your vehicle exhaust system temperature exceeds intended operating range. If this warning occurs, a chime will sound, followed by reduced engine power. The engine will shut down when your vehicle speed is below 3 mph (5 km/h). Stop the vehicle as soon as safely possible. Have the system checked

by an authorized dealer.

The diluted engine oil needs to be changed. Refer to your

diesel supplement for more information.

96

Super Duty (), enUSA

Message

ENGINE TURNS OFF IN

1 SECOND

ENGINE TURNS OFF IN

XX SECONDS

ENGINE TURNED OFF

ENGINE WARMING

PLEASE WAIT

Information Displays

Action

The powertrain control module will intentionally turn the engine off due to your vehicle being in the final second of a countdown. The diesel engine shutdown is a (regulatory) requirement, which may be required of a particular diesel vehicle for sale in states requiring this feature. Refer to your

diesel supplement for more information..

The powertrain control module will intentionally turn the

engine off due to your vehicle being in the final 30 seconds of a countdown. The diesel engine shutdown for extended idling

is an optional feature. Refer to your diesel supplement for

more information.

Appears after the 30 second countdown. Refer to your diesel

supplement for more information.

In extremely cold weather, typically below –15°F (–26°C) and if the engine block heater is not utilized, your engine will not respond to accelerator pedal movement for 30 seconds. This restriction allows your engine to circulate the oil properly in order to avoid engine damage. Refer to your diesel supple-

ment for more information.

EXHAUST FILTER DRIVE

COMPLETE

Your diesel particulate filter is clean. Refer to your diesel

supplement for more information.

EXHAUST FILTER

CLEANED

EXHAUST CLEAN

STOPPED

EXHAUST FLUID RANGE

XXX MI

IN XX MILES, SPEED LIMITED TO XX MPH

EXHAUST FLUID EMPTY

SPEED LIMITED TO XX MPH UPON RESTART EXHAUST FLUID EMPTY

Your diesel particulate filter is clean. Refer to your diesel

supplement for more information.

The manual operator commanded regeneration process has stopped. Refer to your diesel supplement for more informa-

tion.

The distance you can travel before depleting the remaining diesel exhaust fluid. Refer to your diesel supplement for more

information.

Your diesel exhaust fluid is nearing empty. Your vehicle’s top speed will become limited in the displayed distance. You must replenish the diesel exhaust fluid to resume normal operation

of your vehicle. Refer to your diesel supplement for more

information.

Your remaining diesel exhaust fluid has depleted. Your speed

will be limited upon restart. You must replenish the diesel exhaust fluid to resume normal operation of your vehicle.

Refer to your diesel supplement for more information.

97

Super Duty (), enUSA

Message

SPEED LIMITED TO XX MPH EXHAUST FLUID

EMPTY

ENGINE IDLED SOON EXHAUST FLUID EMPTY

Information Displays

Action

The diesel exhaust fluid is empty. You must replenish the diesel exhaust fluid to resume normal operation of your

vehicle. Refer to your diesel supplement for more information. The selective catalytic reduction system detects low exhaust fluid. The engine will eventually enter into an idle only mode. You must replenish the diesel exhaust fluid to resume normal operation of your vehicle. Refer to your diesel supplement for

more information.

ENGINE IDLED - SEE OWNER’S MANUAL

EXHAUST FLUID EMPTY

A problem exists with the selective catalytic reduction system. The vehicle will enter into an idle-only mode. If the exhaust fluid is empty, you must replenish the diesel exhaust fluid to resume normal operation of your vehicle. Refer to your diesel

supplement for more information.

IN XX MILES, SPEED LIMITED TO 50 MPH

EXHAUST FLUID SYSTEM FAULT

SPEED LIMITED TO 50
MPH UPON RESTART

EXHAUST FLUID SYSTEM FAULT

SPEED LIMITED TO 50
MPH EXHAUST FLUID

SYSTEM FAULT

ENGINE IDLED SOON

EXHAUST FLUID

SYSTEM FAULT SEE

MANUAL

ENGINE IDLED - SEE OWNER’S MANUAL

EXHAUST FLUID SYSTEM FAULT

The selective catalytic reduction system detects a fault. The

vehicle’s top speed will become limited in the displayed

distance starting at 50 miles (80 km) and count down from this point. Refer to your diesel supplement for more informa-

tion. Have the system checked by an authorized dealer.

The selective catalytic reduction system detects a fault. The vehicle’s top speed will become limited upon restarting. Refer

to your diesel supplement for more information. Have the

system checked by an authorized dealer.

The selective catalytic reduction system detects a fault. The vehicle’s top speed is limited. Refer to your diesel supplement

for more information. Have the system checked by an

authorized dealer.

The selective catalytic reduction system detects a fault. The engine will enter into an idle only mode. Refer to your diesel supplement for more information. Have the system checked

by an authorized dealer.

The selective catalytic reduction system detects a fault. The engine will eventually enter into an idle-only mode. Press OK to override the idle mode. Refer to your diesel supplement for more information. Have the system checked by an authorized

dealer.

FUEL FILTER CHANGE

REQUIRED

A fuel filter change is required. See Normal Scheduled

Maintenance (page 460).

98

Super Duty (), enUSA

Information Displays

Action

You must have your vehicle serviced by an authorized dealer if approximately two hours after the EXHAUST OVERLOADED DRIVE TO CLEAN message has displayed and you have not driven your vehicle above 30 mph (48 km/h) for at least 20
minutes to clean the diesel particulate filter. Refer to your

diesel supplement for more information.

You are responsible for assuring that you operate your vehicle in a manner that allows diesel particulate filter cleaning to occur. Ignoring the EXHAUST OVER LIMIT SERVICE NOW warning message could lead to reduced drivability and

customer expense, including damage to the diesel particulate filter. Your new vehicle warranty may not cover this damage. The water separator has reached a predetermined capacity and needs draining. Refer to your diesel supplement for more

information.

A low fuel pressure condition has occurred due to cold, low fuel level or fuel filters need to be changed. Refer to your diesel

supplement for more information.

Action

The door listed is not completely closed.

Action

The electronic locking differential is engaged.

The electronic locking differential is disengaged.

The electronic locking differential requests a certain speed

requirement to engage.

Message

EXHAUST OVER LIMIT

SERVICE NOW

WATER IN FUEL DRAIN FILTER SEE MANUAL

LOW FUEL PRESSURE

Doors and Locks

Message X Door Ajar

Drivetrain

Message

LOCKING DIFFERENTIAL

ENGAGED

ELD ENGAGED

LOCKING DIFFERENTIAL

DISENGAGED

ELD DISENGAGED

TO ENGAGE LOCKING DIFFERENTIAL SLOW

TO XX MPH/KM/H

99

Super Duty (), enUSA

Information Displays

Action

The electronic locking differential request the release of the

accelerator pedal in order to engage.

The electronic locking differential requests a certain speed

requirement to engage.

The electronic locking differential requests a certain speed

requirement to engage.

An electronic locking differential system fault is present. See

Using Four-Wheel Drive (page 153).

A reminder to shift into park.

Message

TO ENGAGE ELD SLOW

TO XX MPH/KM/H

TO ENGAGE LOCKING DIFFERENTIAL RELEASE ACCELERATOR PEDAL

TO ENGAGE ELD RELEASE PEDAL

SLOW VEHICLE TO XX

KM/H FOR ELD

SLOW VEHICLE TO XX

MPH FOR ELD CHECK LOCKING DIFFERENTIAL SHIFT TO PARK

Engine

Message

TRANSPORT MODE CONTACT

DEALER

POWER REDUCED TO LOWER

ENGINE TEMP

Fuel

Message

FUEL LEVEL LOW CHECK FUEL CAP

Action

Your vehicle is set to transport mode. The transport mode disables certain vehicle functions to prevent

battery discharge.

The engine has reduced power in order to help reduce high coolant temperature See Engine Coolant Check

(page 236).

Action

An early reminder of a low fuel condition. The fuel cap may not be properly closed.

100

Super Duty (), enUSA

Information Displays

Key

Message

Action

COULD NOT PROGRAM

INTEGRATED KEY

You have attempted to program a fifth integrated key. See

Replacing a Lost Key or Remote Control (page 50).

TO DRIVE: TURN KEY

TO ON

The factory equipped remote start is active. Turn your key to

on to drive.

Maintenance

Message

ENGINE OIL CHANGE SOON

OIL CHANGE REQUIRED

BRAKE FLUID LEVEL LOW

CHECK BRAKE SYSTEM

MyKey®

Message

MYKEY ACTIVE DRIVE SAFELY ADVANCETRAC ALWAYS ON -

MYKEY SETTING

VEHICLE NEAR TOP SPEED

Action

The engine oil life is nearing its end. See Engine Oil

Check (page 235).

The oil life left reaches 0%. See Engine Oil Check

(page 235).

The brake fluid level is low and the brake system needs inspection immediately. See Brake Fluid Check (page

243).

The brake system needs servicing. If the warning stays on or continues to come on, have the system checked

by an authorized dealer as soon as possible.

Action

MyKey is active.

A MyKey is in use and you cannot turn off the electronic

stability control.

A MyKey is in use, the MyKey speed limit is on and your

vehicle speed is approaching 80 mph (130 km/h).

VEHICLE AT TOP SPEED -

MYKEY SETTING

A MyKey is in use, the MyKey speed limit is on and your

vehicle speed is 80 mph (130 km/h).

SPEED LIMITED TO 80 MPH

SPEED LIMITED TO 130 KM/H

When starting your vehicle and MyKey is in use and the

MyKey speed limit is on.

When starting your vehicle and MyKey is in use and the

MyKey speed limit is on.

101

Super Duty (), enUSA

Information Displays

Message

CHECK SPEED DRIVE SAFELY

BUCKLE UP TO UNMUTE

AUDIO

MYKEY COULD NOT PROGRAM

Action

A MyKey is in use, the optional setting is on and your

vehicle exceeds a preselected speed.

A MyKey is in use and Belt-Minder® is active.

An attempt failed to program a spare key using two

existing MyKeys.

Park Aid

Message

CHECK REAR PARK AID

REAR PARK AID OFF REAR PARK AID ON

Park Brake

Message

Action

The transmission is in R (Reverse) and the park aid is

disabled.

The rear park aid is disabled. The rear park aid is enabled.

Action

PARK BRAKE ENGAGED

The parking brake is set and your vehicle is in motion.

Power Steering Message

SERVICE POWER STEERING

SERVICE POWER STEERING

NOW

POWER STEERING ASSIST

FAULT

Action

The power steering system has detected a condition that requires service. Have the system checked by an

authorized dealer.

The power steering system has detected a condition within the power steering system that requires service immediately. Have the system checked by an author-

ized dealer.

The power steering system has disabled power

steering assist due to a system error. Have the system

checked by an authorized dealer.

102

Super Duty (), enUSA

Information Displays

Off Road

Message

Action

HILL DESCENT CONTROL OFF FOR HILL DESCENT REDUCE

SPEED

The driver has disabled hill descent control mode. You have not met the vehicle speed requirement for

entry into off-road mode.

FOR HILL DESCENT SELECT

GEAR

The driver is able to select a transmission gear for hill

descent mode.

HILL DESCENT - DRIVER

RESUME CONTROL

Hill descent control mode is no longer active and the

driver must resume control.

HILL DESCENT CONTROL

FAULT

HILL DESCENT CONTROL OFF

SYSTEM COOLING

HILL DESCENT CONTROL

READY

A hill descent system fault is present.

The hill descent system is cooling due to overuse.

Hill descent control is active.

Tire Pressure Monitoring System

Message

LOW TIRE PRESSURE

TIRE PRESSURE MONITOR FAULT

TIRE PRESSURE SENSOR FAULT

Action

One or more tires on your vehicle have low tire pressure. See

Tire Pressure Monitoring System (page 283).

The tire pressure monitoring system is malfunctioning. If the warning stays on or continues to come on, have the system checked by an authorized dealer. See Tire Pressure Monit-

oring System (page 283).

A tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, see See Tire Pressure Monitoring System (page 283). If the warning stays on or continues to come on, have the system checked by an authorized dealer

as soon as possible.

103

Super Duty (), enUSA

Information Displays

Trailer

Message

TRAILER BRAKE GAIN: XX.X

[OUTPUT]

TRAILER BRAKE GAIN: XX.X NO

TRAILER

TRAILER BRAKE MODULE

FAULT

Action

The current gain setting for the trailer brake.

The current gain setting for the trailer brake when a

trailer is not connected.

Accompanied by a single chime, in response to faults sensed by the TBC. See Trailer Sway Control (page

192).

TRAILER CONNECTED

A correct trailer connection (a trailer with electric trailer

brakes) is sensed during a given ignition cycle.

TRAILER DISCONNECTED

A trailer connection becomes disconnected, either intentionally or unintentionally, and has been sensed during a given ignition cycle. Disregard this status if your vehicle is not equipped with a factory installed trailer brake controller. This message may appear when an aftermarket TBC is used even when the trailer is

connected.

TRAILER SWAY REDUCE

SPEED

Your trailer sway control has detected trailer sway so

you need to reduce your speed.

WIRING FAULT ON TRAILER

Faults with your vehicle wiring and trailer wiring or