2015 Ford F 250 Owners Manual

Download PDF Manual
130 (210) 149 (240) 268 Super Duty (), enUSA Wheels and Tires Letter rating mph ( km/h) 168 (270) 186 (299) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299 km/h), tire manufacturers always use the letters ZR. H. U.S. DOT Tire Identification Number: This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. I. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. K. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-pillar or the edge of the driver's door. L. Treadwear, Traction and Temperature Grades: *Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear 1½ times as well on the government course as a tire graded 100. *Traction: The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. 269 Super Duty (), enUSA Wheels and Tires *Temperature: The temperature grades are A (the highest), B and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. M. Maximum Inflation Pressure: Indicates the tire manufacturers' maximum permissible pressure or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the vehicle manufacturer's recommended cold inflation pressure which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-pillar or the edge of the driver's door. The cold inflation pressure should never be set lower than the recommended pressure on the vehicle label. The tire suppliers may have additional markings, notes or warnings such as standard load or radial tubeless. Additional Information Contained on the Tire Sidewall for LT Type Tires Note: Tire Quality Grades do not apply to this type of tire. 270 Super Duty (), enUSA LT type tires have some additional information beyond those of P type tires. These differences are described below. A. LT: Indicates a tire, designated by the Tire and Rim Association, that is intended for service on light trucks. B. Load Range and Load Inflation Limits: Indicates the tire's load-carrying capabilities and its inflation limits. C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual; defined as four tires on the rear axle (a total of six or more tires on the vehicle). ABCBDE142544Wheels and Tires A. T: Indicates a type of tire, designated by the Tire and Rim Association, that is intended for temporary service on cars, sport utility vehicles, minivans and light trucks. B. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 80: Indicates the aspect ratio which gives the tire's ratio of height to width. Numbers of 70 or lower indicate a short sidewall. D.D: Indicates a diagonal type tire. R: Indicates a radial type tire. E. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. Location of the Tire Label You will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B-Pillar or the edge of the driver's door. Inflating Your Tires Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. D. Maximum Load Single lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single; defined as two tires (total) on the rear axle. Information on T Type Tires T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire. T type tires have some additional information beyond those of P type tires. These differences are described below: 271 Super Duty (), enUSA ABCDEE142545Wheels and Tires Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns WARNING Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or blowout, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents. A tire can lose up to half of its air pressure and not appear to be flat! Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label or Tire Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-pillar or the edge of the driver's door. Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles 272 Super Duty (), enUSA Wheels and Tires Note: Do not reduce tire pressure to change the ride characteristics of the vehicle. If you do not maintain the inflation pressure at the levels specified by Ford, your vehicle may experience a condition known as shimmy. Shimmy is a severe vibration and oscillation in the steering wheel after the vehicle travels over a bump or dip in the road that does not dampen out by itself. Shimmy may result from significant under-inflation of the tires, improper tires (load range, size, or type), or vehicle modifications such as lift-kits. In the event that your vehicle experiences shimmy, you should slowly reduce speed by either lifting off the accelerator pedal or lightly applying the brakes. The shimmy will cease as the vehicle speed decreases. Maximum Inflation Pressure is the tire manufacturer's maximum permissible pressure and the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-pillar or the edge of the driver's door. The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire Label. When weather temperature changes occur, tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. Note: If you are checking tire pressure when the tire is hot, (for example, driven more than 1 mile [1.6 kilometers]), never bleed or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recommended cold pressures. A hot tire at or below recommended cold inflation pressure could be significantly under-inflated. 273 Super Duty (), enUSA Wheels and Tires Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pressing on the metal stem in the center of the valve. Then recheck the pressure with your tire gauge. 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires operate at a higher inflation pressure than the other tires. For T type mini-spare tires, (see the Dissimilar spare wheel and tire assembly information for a description. Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires, see the Dissimilar spare wheel and tire assembly information for a description. Store and maintain at the higher of the front and rear inflation pressure as shown on the Safety Compliance Certification Label or Tire Label. 6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts or bulges. Tire Inflation Information WARNING An inflated tire and rim can be very dangerous if improperly used, serviced or maintained. To reduce the risk of serious injury, never attempt to re-inflate a tire which has been run flat or seriously under-inflated without first removing the tire from the wheel assembly for inspection. Do not attempt to add air to tires or replace tires or wheels without first taking precautions to protect persons and property. All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. Tire service, including adjusting tire pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Safety and Health Administration regulations. For example, during 274 Super Duty (), enUSA Wheels and Tires any procedure involving tire inflation, the technician or individual must utilize a remote inflation device, and ensure that all persons are clear of the trajectory area. 275 Super Duty (), enUSA E161437Wheels and Tires wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist: WARNING Stay out of the trajectory (1) as indicated in the illustration. Inspecting Your Tires and Wheel Valve Stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that may permit air leakage and repair or replace the tire and replace the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive 276 Super Duty (), enUSA E1614381Wheels and Tires or suspected have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended. Age WARNING Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed, inflation pressure) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear. However, heat caused by hot climates or frequent high loading conditions can accelerate the aging process and may require tires to be replaced more frequently. You should replace your spare tire when you replace the road tires or after six years due to aging even if it has not been used. U.S. DOT Tire Identification Number Both United States and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and Tire Wear When the tread is worn down to one sixteenth of an inch (2 millimeters), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or wear bars, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to one sixteenth of an inch (2 millimeters). When the tire tread wears down to the same height as these wear bars, the tire is worn out and must be replaced. Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed 277 Super Duty (), enUSA E142546Wheels and Tires WARNINGS may be found on either the Safety Compliance Certification Label or the Tire Label. If this information is not found on these labels then you should contact your authorized dealer as soon as possible. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure. If you have questions regarding tire replacement, contact your authorized dealer as soon as possible. To reduce the risk of serious injury, when mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. Tire Replacement Requirements Your vehicle is equipped with tires designed to provide a safe ride and handling capability. WARNINGS Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size 278 Super Duty (), enUSA Wheels and Tires The two front tires or two rear tires should generally be replaced as a pair. The tire pressure sensors mounted in the wheels are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the tire pressure monitoring system indicator is flashing, the system is malfunctioning. Your replacement tire might be incompatible with your tire pressure monitoring system, or some component of the system may be damaged. Replacing a Tire That is Greenhouse Gas Certified The tires installed on this vehicle at the factory as original equipment are certified for Greenhouse Gas and Fuel Efficiency regulations. Replacement tires must be of equal or lower rolling resistance level (TRRL or Crr). Consult with your tire supplier(s) for appropriate replacement tires. WARNINGS When inflating the tire for mounting pressures up to 20 psi (1.38 bar) greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1. Make sure that you have the correct tire and wheel size. 2. Lubricate the tire bead and wheel bead seat area again. 3. Stand at a minimum of 12 feet (3.6 meters) away from the wheel and tire assembly. 4. Use both eye and ear protection. For a mounting pressure more than 20 psi (1.38 bar) greater than the maximum pressure, a Ford dealer or other tire service professional should do the mounting. Always inflate steel carcass tires with a remote air fill with the person inflating standing at a minimum of 12 feet (3.6 meters) away from the wheel and tire assembly Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle 279 Super Duty (), enUSA Wheels and Tires Safety Practices WARNINGS If your vehicle is stuck in snow, mud, or sand, do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Driving habits have a great deal to do with your tire mileage and safety. *Observe posted speed limits *Avoid fast starts, stops and turns *Avoid potholes and objects on the road *Do not run over curbs or hit the tire against a curb when parking Highway Hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road. Stop and inspect the tires for damage. If a tire is under-inflated or damaged, deflate it, remove wheel and replace it with your spare tire and wheel. If you cannot detect a cause, have the vehicle towed to the nearest repair facility or tire dealer to have the vehicle inspected. Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically. Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front-wheel drive vehicles and those with an independent rear suspension may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. 280 Super Duty (), enUSA Wheels and Tires Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. Rear-wheel drive vehicles and four-wheel drive vehicles (front tires at left of diagram) Dual rear wheel drive vehicle - six tire rotation (front tires at top of diagram) Tire Rotation WARNING If the tire label shows different tire pressures for the front and rear tires and the vehicle is equipped with a tire pressure monitoring system, then the settings for the system sensors need to be updated. Always perform the system reset procedure after tire rotation. If the system is not reset, it may not provide a low tire pressure warning when necessary. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare wheel and tire assembly. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare wheel and tire assembly it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements. 281 Super Duty (), enUSA E142548Wheels and Tires USING SNOW CHAINS WARNING Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally, the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure. Note: Do not use snow chains on vehicles with 20 inch wheels and tires. The tires on your vehicle have all-weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and cables. If you need to use cables, it is recommended that steel wheels (of the same size and specifications) be used, as cables may chip aluminum wheels. Note: The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains. Follow these guidelines when using snow tires and chains: • If possible, avoid fully loading your vehicle • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. We do not recommend splitting up the dual rear wheels. Rotate them side to side as a set. After tire rotation, inflation pressures must be adjusted for the tires new positions in accordance with vehicle requirements. Sometimes irregular tire wear can be corrected by rotating the tires. 282 Super Duty (), enUSA E166988Wheels and Tires your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. • Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and retighten the chains. If this does not work, remove the chains to prevent damage to your vehicle. • Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. If you have any questions regarding snow chains or cables, please contact your authorized dealer. TIRE PRESSURE MONITORING SYSTEM WARNING Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term "IC:" before the radio certifications number only signifies that Industry Canada technical specifications were met. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check 283 Super Duty (), enUSA Wheels and Tires You should always have your tires serviced by an authorized dealer. Check the tire pressure periodically (at least monthly) using an accurate tire gauge. See Inflating Your Tires in this chapter. Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low. Once the light is illuminated, your tires are under-inflated and need to be inflated to the manufacturer’s recommended tire pressure. Even if the light turns on and a short time later turns off, your tire pressure still needs to be checked. When Your Temporary Spare Tire is Installed When one of your road tires needs to be replaced with the temporary spare, the system will continue to identify an issue to remind you that the damaged road wheel and tire assembly needs to be repaired and put back on your vehicle. To restore the full function of the tire pressure monitoring system, have the damaged road wheel and tire assembly repaired and remounted on your vehicle. When You Believe Your System is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. See the following chart for information concerning your tire pressure monitoring system: The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with part 15 of the FCC Rules and with Licence exempt RSS Standards of Industry Canada. Operation is subject to the following two conditions: • This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. • Changing Tires With a Tire Pressure Monitoring System Note: Each road tire is equipped with a tire pressure sensor located inside the wheel and tire assembly cavity. The pressure sensor is attached to the valve stem. The pressure sensor is covered by the tire and is not visible unless the tire is removed. Take care when changing the tire to avoid damaging the sensor. 284 Super Duty (), enUSA E142549Wheels and Tires Low tire pressure warning light Possible cause Customer action required Solid warning light Tire(s) under-inflated Spare tire in use Tire pressure monitoring system malfunction Tire rotation without sensor training Flashing warning light Spare tire in use Tire pressure monitoring system malfunction Make sure tires are at the proper pres- sure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off. Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible. On vehicles with different front and rear tire pressures, the system must be retrained following every tire rotation. See Tire Care (page 265). Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible. 285 Super Duty (), enUSA Wheels and Tires When Inflating Your Tires When putting air into your tires (such as at a gas station or in your garage), the tire pressure monitoring system may not respond immediately to the air added to your tires. It may take up to two minutes of driving over 20 mph (32 km/h) for the light to turn off after you have filled your tires to the recommended inflation pressure. How Temperature Affects Your Tire Pressure The tire pressure monitoring system monitors tire pressure in each pneumatic tire. While driving in a normal manner, a typical passenger tire inflation pressure may increase about 2 to 4 psi (14 to 28 kPa) from a cold start situation. If the vehicle is stationary overnight with the outside temperature significantly lower than the daytime temperature, the tire pressure may decrease about 3 psi (21 kPa) for a drop of 30°F (17°C) in ambient temperature. This lower pressure value may be detected by the tire pressure monitoring system as being significantly lower than the recommended inflation pressure and activate the system warning light for low tire pressure. If the low tire pressure warning light is on, visually check each tire to verify that no tire is flat. If one or more tires are flat, repair as necessary. Check the air pressure in the road tires. If any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. Tire Pressure Monitoring System Reset Procedure WARNING To determine the required pressure(s) for your vehicle, see the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-Pillar or the edge of the driver's door. Note: You need to perform the tire pressure monitoring system reset procedure after each tire rotation on vehicles that require different recommended tire pressures in the front tires as compared to the rear tires. Overview To provide the vehicle's load carrying capability, some vehicles require different recommended tire pressures in the front tires as compared to the rear tires. The tire pressure monitoring system equipped on these vehicles is designed to illuminate the low tire pressure warning light at two different pressures; one for the front tires and one for the rear tires. Since tires need to be rotated to provide consistent performance and maximum tire life, the tire pressure monitoring system needs to know when the tires are rotated to determine which set of tires are on the front and which are on the rear. With this information, the system can detect and properly warn of low tire pressures. System reset tips: 286 Super Duty (), enUSA Wheels and Tires • To reduce the chances of interference from another vehicle, perform the system reset procedure at least three feet (one meter) away from another Ford Motor Company vehicle undergoing the system reset procedure at the same time. • Do not wait more than two minutes between resetting each tire sensor or the system will time-out and the entire procedure will have to be repeated on all four wheels. • A double horn will sound indicating the need to repeat the procedure. Performing the System Reset Procedure Read the entire procedure before attempting. 1. Drive the vehicle above 20 mph (32 km/h) for at least two minutes, then park in a safe location where you can easily get to all four tires and have access to an air pump. 2. Place the ignition in the off position and keep the key in the ignition. 3. Cycle the ignition to the on position with the engine off. 4. Turn the hazard flashers on then off three times. You must accomplish this within 10 seconds. If the reset mode has been entered successfully, the horn will sound once, the system indicator will flash and a message is shown in the information display. If this does not occur, please try again starting at Step 2. If after repeated attempts to enter the reset mode, the horn does not sound, the system indicator does not flash and no message is shown in the information display, seek service from your authorized dealer. 5. Train the tire pressure monitoring system sensors in the tires using the following system reset sequence starting with the left front tire in the following clockwise order: Left front (driver's side front tire), Right front (passenger's side front tire), Right rear (passenger's side rear tire), Left rear (driver's side rear tire). 6. Remove the valve cap from the valve stem on the left front tire. Decrease the air pressure until the horn sounds. Note: The single horn chirp confirms that the sensor identification code has been learned by the module for this position. If a double horn is heard, the reset procedure was unsuccessful, and you must repeat it. 7. Remove the valve cap from the valve stem on the right front tire. Decrease the air pressure until the horn sounds. 8. Remove the valve cap from the valve stem on the right rear tire. Decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire. Decrease the air pressure until the horn sounds. Training is complete after the horn sounds for the last tire trained (driver's side rear tire), the system indicator stops flashing, and a message is shown in the information display. 10. Turn the ignition off. If two short horn beeps are heard, the reset procedure was unsuccessful and you must repeat it. If after repeating the procedure and two short beeps are heard when the ignition is turned to off, seek assistance from your authorized dealer. 287 Super Duty (), enUSA Wheels and Tires 11. Set all four tires to the recommended air pressure as indicated on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position) or Tire Label located on the B-Pillar or the edge of the driver's door. CHANGING A ROAD WHEEL WARNINGS The use of tire sealant may damage your tire pressure monitoring system and should only be used in roadside emergencies. If you must use a sealant, the Ford Tire Mobility Kit sealant should be used. The tire pressure monitoring system sensor and valve stem on the wheel must be replaced by an authorized dealer after use of the sealant. If the tire pressure monitor sensor becomes damaged, it will no longer function. See Tire Pressure Monitoring System (page 283). Note: If your vehicle is equipped with the tire pressure monitoring system, the indicator light will illuminate when the spare tire is in use. To restore the full function of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. If your vehicle is equipped with the tire pressure monitoring system, have a flat serviced by an authorized dealer in order to prevent damage to the system sensors. See Tire Pressure Monitoring System (page 283). Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have the authorized dealer inspect the system sensor for damage. Dissimilar Spare Wheel and Tire Assembly Information WARNING Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare wheel and tire, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road wheel and tire assembly that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS WHEEL AND TIRE ASSEMBLY FOR TEMPORARY USE ONLY When driving with one of the dissimilar spare tires listed above, do not: 288 Super Duty (), enUSA Wheels and Tires • • Exceed 50 mph (80 km/h) Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label. Tow a trailer. • • Use snow chains on the end of the vehicle with the dissimilar spare tire. • Use more than one dissimilar spare tire at a time. • Use commercial car washing equipment. Try to repair the dissimilar spare tire. • Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance. • Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability. 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare wheel and tire assembly, do not: • • Use more than one dissimilar spare wheel and tire assembly at a time. Exceed 70 mph (113 km/h). • Use commercial car washing equipment. • Use snow chains on the end of the vehicle with the dissimilar spare wheel and tire assembly. The usage of a full-size dissimilar spare wheel and tire assembly can lead to impairment of the following: • Handling, stability and braking performance. • Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability. When driving with the full-size dissimilar spare wheel and tire assembly additional caution should be given to: • • Driving vehicles equipped with a Towing a trailer. camper body. • Driving vehicles with a load on the cargo rack. Drive cautiously when using a full-size dissimilar spare wheel and tire assembly and seek service as soon as possible. Location of the Spare Tire and Tools If your vehicle is equipped with a spare tire, jack and associated tools, see the following table for their locations: Tool Location Spare tire (pick-up trucks only) Under the vehicle, just forward of the rear bumper Regular cab and Crew Cab: Fastened to floor pan behind rearmost seat on passenger side Jack 289 Super Duty (), enUSA Wheels and Tires Tool Location SuperCab: Under rear bench seat on passenger side Regular cab: Fastened to floor behind driver SuperCab: Fastened to floor under rear seat Crew Cab: Fastened to floor behind rear seat seat at driver side In the glove box Jack handle, lug wrench, lug wrench exten- sion (only available on dual rear wheel vehicles) and wheel chock (only available on single rear wheel vehicles equipped with a diesel engine) Key and spare tire lock Removing the Spare Tire (With Spare Tire Carrier Only) The following tools are required to remove the spare tire: One handle extension and two typical extensions. To assemble, align the button with the hole and slide the parts together. To disconnect, press the button and pull apart. 290 Super Duty (), enUSA One wheel nut wrench. Slide over the square end of the jack handle. Note: For vehicles with dual rear wheels, insert the lug wrench extension into the lug wrench to reach the lug nuts. E162795E162796E162797Wheels and Tires 1. Attach the spare tire lock key (A) to the jack handle (B). 5. Lift the spare tire on end to access the tether attachment. 7. 6. Use the lug wrench to remove the lug nut from the spare tire tether. If not replacing the spare or flat tire to the underbody storage area, raise the wheel retainer up into the installed position. 8. Use the attached fastener strap (on the spare tire tether) to attach the tether end to the winch retainer prior to raising to the installed position. Tire Change Procedure WARNINGS When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in park (P). To help prevent the vehicle from moving when you change a tire, be sure to place the transmission in park (P), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. Never get underneath a vehicle that is supported only by a jack. If the vehicle slips off the jack, you or someone else could be seriously injured. 2. Fully insert the jack handle (with one extension) through the bumper hole and into the guide tube. The key and lock will engage with a slight push and counterclockwise turn. You will feel some resistance when you turn the jack handle assembly. 3. Turn the handle counterclockwise and lower the spare tire until you can slide the tire rearward and the cable is slack. 4. Remove the retainer through the center of the wheel. If your vehicle is equipped with a tether, perform the following steps. 291 Super Duty (), enUSA E162798ABABE162799E162800Wheels and Tires WARNINGS Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Always use the jack provided as original equipment with your vehicle. If using a jack other than the one provided as original equipment with your vehicle, make sure the jack capacity is adequate for the vehicle weight, including any vehicle cargo or modifications. Note: Passengers should not remain in the vehicle when the vehicle is being jacked. Park on a level surface, set the parking brake and activate the hazard flashers. F-250 and F-350 Single Rear Wheel Vehicles 1. Insert the hooked end of the jack handle into the jack and use the handle to slide the jack under the vehicle. 2. Position the jack according to the following guides: 1. Turn the engine off and block the wheel that is diagonally opposite of the flat tire using the wheel chock. Note: Lock the manual hub on the wheel if the vehicle is a 4x4. 2. Remove the jack, jack handle, lug wrench and spare tire from the stowage locations. 3. Use the tip of the lug wrench to remove any wheel trim. 4. Loosen each wheel lug nut ½ turn counterclockwise, but do not remove them until the wheel is raised off the ground. Super Duty (), enUSA Front (4x2). Front driver side (4x4). 292 E142551E162801E162802E162803Wheels and Tires Note: Make sure the jack fits onto the flat area on the outboard side of the differential. Jacking the Vehicle Front passenger side (4x4). Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle. Rear Note: Jack at the specified locations to avoid damage to the vehicle. 1. Turn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire. 2. Remove the lug nuts with the lug wrench. 3. Replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front wheels and single rear wheel vehicles. If you are replacing an inboard rear tire on dual rear wheel vehicles, the valve stem must be facing outward. If you are replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 4. Lower the wheel by turning the jack handle counterclockwise. 5. Remove the jack and fully tighten the lug nuts in the order shown. See Technical Specifications (page 299). 6. Stow the flat tire. See Stowing the flat or spare tire if the vehicle is equipped with a spare tire carrier. 7. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does not rattle when driving. 8. Unblock the wheels. 293 Super Duty (), enUSA E162804E162805E162811Wheels and Tires 8-lug nut torque sequence. 10-lug nut torque sequence. If the ornament retention towers are aligned between the studs or lug nuts, the ornament is improperly installed. This improper installation may appear and sound correct, but will not keep the ornament on the vehicle. Ornaments improperly installed in this manner will fall off or become loose with minimal force or impact. F-350 Dual Rear Wheel, F-450 and F-550 Vehicles 1. Slide the notched end of the jack handle over the release valve and use the handle to slide the jack under the vehicle. Make sure the valve is closed by turning it clockwise. 2. Position the jack according to the following guides: When installing the wheel center ornaments, make sure that the ornament retention towers on the back side of the ornament are aligned with the studs or lug nuts. The retention towers are designed to be installed over the studs or nuts and retain to the flange on the lug nut. 294 Super Duty (), enUSA E1614411342765812345678910E169375E162820E162821E162812Wheels and Tires Note: View shown from the rear of the vehicle to clearly identify the jack point. Note: Place the jack directly under the axle and inboard of the radius arm so that the jack clears the radius arm. Front (4x2): F-350 dual rear wheel. Note: Place the jack directly under the I-beam. Front: F-450 and F-550. Front driver side (4x4): F-350 dual rear wheel. Note: Make sure the jack fits onto the flat area on the outboard side of the differential housing. Rear: F-350 dual rear wheel. Front passenger side (4x4): F-350 dual rear wheel. Rear: F-450 and F-550. 295 Super Duty (), enUSA E162813E162814E162815E162816E162817E162818Wheels and Tires Jacking the Vehicle 8. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does not rattle when driving. 9. Unblock the wheels. 1. Insert the jack handle into the pump linkage. 8-lug nut torque sequence. 10-lug nut torque sequence. Installing Dual Rear Wheel Ornaments 2. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Note: Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack's rated capacity. 3. Remove the lug nuts with the lug wrench. 4. Replace the flat tire with the spare tire, making sure the valve stem is facing outward on all front an inboard rear wheels. If you are replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 5. Lower the wheel by slowly turning the release valve counterclockwise. Opening the release valve slowly will provide a more controlled rate of descent. 6. Remove the jack and fully tighten the lug nuts in the order shown. See Technical Specifications (page 299). 7. Stow the flat tire. See Stowing the flat or spare tire if the vehicle is equipped with a spare tire carrier. 296 Super Duty (), enUSA E162819E1614411342765812345678910E169375ABE162822Wheels and Tires 1. Align the ornament with the lug nuts. A is the clip and B is the flange. 2. Hold the ornament so that all of the retention clips are sitting on the flange of the lug nuts. 3. Use your hand or rubber mallet to tap the ornament in a star pattern. There should be an even gap between the ornament and the wheel. 4. Be sure to install all the clips on the nuts over the flanges so that there is an even gap all around and the retention clips are fully seated. Stowing the Flat or Spare Tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. Note: If you are stowing a tire that requires reattaching it to the vehicle with a tether, perform these steps first, then proceed with the following steps. 1. Place the tire on end with the valve stem facing toward the front of the vehicle. 2. Place the tether into the bolt holes in the wheel and attach the lug nut using the lug wrench. 297 Super Duty (), enUSA E162823ACBDE162824E162825E162826Wheels and Tires to the maximum tightness. Tighten to the best of your ability, to the point where the ratchet/slip occurs, if possible. The spare tire carrier will not allow you to overtighten. If the spare tire carrier ratchets or slips with little effort, take the vehicle to your authorized dealer for assistance at your earliest convenience. 6. Check that the tire lies flat against the frame and is properly tightened. Try to push or pull, then turn the tire to be sure it will not move. Loosen and retighten, if necessary. Failure to properly stow the spare tire may result in failure of the winch cable and loss of the tire. 7. Repeat this tightness check procedure when servicing the spare tire pressure (every six months, per scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components. If removed, install the spare tire lock into the bumper drive tube with the spare tire lock key and jack handle. 8. 3. Lay the tire on the ground with the valve stem facing up. 4. Slide the wheel partially under the vehicle and install the retainer through the wheel center. Pull on the cable to align the components at the end of the cable. 5. Turn the jack handle clockwise until the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when the tire is raised 298 Super Duty (), enUSA E162800Wheels and Tires TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, resulting in loss of control. Bolt size M14 x 1.5 lb.ft (Nm) 165 lb.ft (224 Nm) *Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque at 100 miles (160 kilometers) after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal). On vehicles equipped with dual rear wheels, retighten the wheel lug nuts to the specified torque at 100 miles (160 kilometers), and again at 500 miles (800 kilometers) of new vehicle operation and after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal). It is important to follow the proper wheel mounting and lug nut torque procedures. On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel stud threads. 299 Super Duty (), enUSA E161443Wheels and Tires Wheel pilot bore Inspect the wheel pilot hole and mounting surface prior to installation. Remove any visible corrosion or loose particles. 300 Super Duty (), enUSA E145950Capacities and Specifications ENGINE SPECIFICATIONS Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio Drivebelt Routing 6.2L Engines 6.2L V8 Engine 6.8L V10 Engine 378 Minimum 87 octane 1-5-4-8-6-3-7-2 Coil on plug 0.041-0.047 inch (1.04-1.20 mm) 9.8:1 413 Minimum 87 octane 1-6-5-10-2-7-3-8-4-9 Coil on plug 0.039-0.043 inch (1.00- 1.10mm) 9.2:1 6.8L Engines with A/C 6.8L Engines without A/C 301 Super Duty (), enUSA E163761E163762E163763Capacities and Specifications MOTORCRAFT PARTS Component Air filter element Oil filter Battery (standard) Battery (optional) 6.2L V8 engine FA-1883 FL-820-S BXT-65-650 BXT-65-750 6.8L V10 engine FA-1883 FL-820-S BXT-65-650 BXT-65-750 Spark plugs-platinum CYFS12FP/SP-526 HJFS-24FP/SP-509 Seat filter Windshield wiper blade FS-104 WW-2201-P FS-104 WW-2201-P For scheduled maintenance, we recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com. These parts meet or exceed Ford Motor Company’s specifications and are engineered for your vehicle. Use of other parts may impact vehicle performance, emissions and durability. Your warranty may be void for any damage related to use of other parts. If a Motorcraft oil filter is not available, use an oil filter that meets industry performance specification SAE/USCAR-36. For spark plug replacement, contact an authorized dealer. Replace the spark plugs at the appropriate intervals. See Scheduled Maintenance (page 457). 302 Super Duty (), enUSA Capacities and Specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel. Make, vehicle line, series, body type Engine type Check digit Model year Assembly plant Production sequence number VEHICLE CERTIFICATION LABEL Please note that in the graphic, XXXX is representative of your vehicle identification number. The Vehicle Identification Number contains the following information: World manufacturer identifier Brake system, Gross Vehicle Weight Rating, Restraint Devices and their locations 303 Super Duty (), enUSA The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label shall be affixed to either the door hinge pillar, the door latch post, or the edge of the door near the door latch, next to the driver's seating position. E142476E142477E167469Capacities and Specifications TRANSMISSION CODE DESIGNATION The transmission code is on the Safety Compliance Certification Label. The following table shows the transmission code along with the transmission description. Description Five-speed automatic transmission 5R110W Six-speed automatic transmission 6R140 Six-speed automatic transmission 6R140W Code 304 Super Duty (), enUSA E167814Capacities and Specifications TECHNICAL SPECIFICATIONS Item Capacity Ford part name or equivalent Ford part number / Ford specification Front axle 5.8 pints (2.8L) Spindle bearing — Motorcraft SAE 80W-90 Premium Rear Axle Lubricant High Temperature 4X4 Front Axle and Wheel Bearing Grease XY-80W90–QL / WSP-M2C197–A XG-11 / WSS-M1C267-A1 Rear axle - F-250/350 (10.50 inch axle)1 6.9 pints (3.3L) Motorcraft SAE 75W-140 Synthetic Rear Axle Lubricant XY-75W140–QL (U.S.) / WSL-M2C192-A CXY-75W140-1L (Canada) / WSL-M2C192-A Rear axle - F-350 (Dana M80) 8.5 pints (4.0L) Motorcraft SAE 75W-90 Synthetic Rear Axle Lubricant XY-75W90–QLS / WSS–M2C918–A XY-75W140–QL (U.S.) / WSL-M2C192-A CXY-75W140-1L (Canada) / WSL-M2C192-A PM-1-C (U.S.) / WSS-M6C65-A1 CPM-1-C (Canada) / WSS-M6C65-A1 PM-20 / WSS- M6C65-A2 VC-3DIL-B (U.S.) / WSS-M97B44-D2 CVC-3DIL-B (Canada) / Rear axle - F-450/550 (Dana S110/S130) 14.0 pints (6.6L) Motorcraft SAE 75W-140 Synthetic Rear Axle Lubricant Brake fluid2 Between MIN/ MAX on brake fluid reservoir Motorcraft High Performance DOT 3 LV Motor Vehicle Brake Fluid Motorcraft High Performance DOT 4 LV Motor Vehicle Brake Fluid Engine coolant (6.2L V8)3 21.3 qt (20.2 L) Motorcraft Orange Antifreeze/Coolant Prediluted 305 Super Duty (), enUSA Capacities and Specifications Item

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2015 Ford F 250 Owners Manual