2006 Ford Crown Victoria Owners Manual

Tires, Wheels and Loading

capacity to carry you, 4 of your friends and all the golf bags? You and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 – (5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb. Yes, you have enough load capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635 kg — (5 x 99 kg) — (5 x 13.5 kg) = 635 — 495 — 67.5 = 72.5 kg. • A final example for your vehicle with 1400 lb. (635 kg) of cargo and

luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb. (45 kg) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x 100) = 1400 – 440 – 1200 = – 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg — (2 x 99 kg) — (12 x 45 kg) = 635 — 198 — 540
= —103 kg. You will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load calculation would be: 1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lb. Now you have the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kg — (2 x 99 kg) — (9 x 45 kg) = 635 — 198 — 405 = 32 kg.

The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Safety Compliance Certification Label found on the edge of the driver’s door.

TRAILER TOWING Your vehicle is classified as a light duty towing vehicle. Do not tow a trailer until your vehicle has been driven at least 2,000 miles (3,200 km). Towing a trailer places an additional load on your vehicle’s engine, transmission, brakes, tires and suspension. Inspect these components carefully after towing. Your loaded trailer should weigh no more than 2,000 lb. (907 kg). Do not exceed the GVWR specified on the Safety Compliance Certification Label.

162

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in

engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.

The GCW of your vehicle and trailer should not exceed 6,600 lb. (2,993 kg).

Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized dealer or a reliable trailer dealer if you require assistance.

Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch. You must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue.

Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper.

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations.

Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough

braking power and your chances of having a collision greatly increase.

The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.

163

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. See your authorized dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps.

Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first 500 miles (800 km) of towing a trailer, and don’t make full throttle starts.

• Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling. (For additional information, refer to Understanding the gearshift positions of the 4–speed automatic transmission in the Driving chapter. • Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance Information for more information.

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you are driving down a long or steep hill, shift to a lower gear. Do not apply the brakes continuously, as they may overheat and become less effective.

• The trailer tongue weight should be 10–15% of the loaded trailer • If you will be towing a trailer frequently in hot weather, hilly

weight.

conditions, at GCW, or any combination of these factors, consider

164

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

refilling your rear axle with synthetic gear lube if not already so equipped. Refer to the Maintenance and Specifications chapter for the lubricant specification. Remember that regardless of the rear axle lube used, do not tow a trailer for the first 500 miles (800 km) of a new vehicle, and that the first 500 miles (800 km) of towing be done at no faster than 70 mph (112 km/h) with no full throttle starts. • After you have traveled 50 miles (80 km), thoroughly check your • To aid in engine/transmission cooling and A/C efficiency during hot • Vehicles with trailers should not be parked on a grade. If you must

weather while stopped in traffic, place the gearshift lever in P (Park).

hitch, electrical connections and trailer wheel lug nuts.

park on a grade, place wheel chocks under the trailer’s wheels.

Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water. Reconnect the wiring to the trailer after the trailer is removed from the water. When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of • do not allow waves to break higher than 6 inches (15 cm) above the

the rear bumper.

bottom edge of the rear bumper.

Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant any time the axle has been submerged in water. Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required.

RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. All Rear Wheel Drive (RWD) vehicles: This applies to all cars and 4x2 trucks/sport utilities with rear wheel drive capability.

165

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading • Place the transmission in N (Neutral) • Maximum speed is 35 mph (56 km/h) • Maximum distance is 50 miles (80 km) If a distance of 50 miles (80 km) or a speed of 35 mph (56 km/h) must be exceeded, you must disconnect the driveshaft. Ford Motor Company recommends the driveshaft be removed/installed only by a qualified technician at an authorized dealer. See your authorized dealer for driveshaft removal/installation. Improper removal/installation of the driveshaft can cause transmission fluid loss, damage to the driveshaft and internal transmission components.

166

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

STARTING

Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts.

Preparing to start your vehicle Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.

Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk

of fire or other damage.

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine

compartment and exhaust system, which can start a fire.

Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.

167

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell

exhaust fumes.

Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than 10 minutes at the higher engine RPM. Before starting the vehicle: 1. Make sure all vehicle occupants have buckled their safety belts. For more information on safety belts and their proper usage, refer to the Seating and Safety Restraints chapter. 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the gearshift is in P (Park).

4. Make sure the parking brake is set.

HOOD

168

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

5. Turn the key to 3 (ON) without turning the key to 4 (START).

Driving

Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) without turning the key to 4 (START). 2. Turn the key to 4 (START), then release the key as soon as the engine starts. Excessive cranking could damage the starter.

Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. Cold weather starting (flexible fuel vehicles only) As the outside temperature approaches freezing, ethanol fuel distributors should supply winter grade ethanol (same as with unleaded gasoline). If summer grade ethanol is used in cold weather conditions, you may experience increased cranking times, rough idle or hesitation until the engine has warmed up. Consult your fuel distributor for the availability of winter grade ethanol. Do not crank the engine for more than 30 seconds at a time as starter damage may occur. If the engine fails to start, turn the key to OFF and wait 30 seconds before trying again.

169

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

Do not use starting fluid such as ether in the air intake system. Such fluid could cause immediate explosive damage to the engine and possible personal injury. If you should experience cold weather starting problems on E85 ethanol, and neither an alternative brand of E85 ethanol nor an engine block heater is available, the addition of unleaded gasoline to your tank will improve cold starting performance. Your vehicle is designed to operate on E85 ethanol alone, unleaded gasoline alone, or any mixture of the two. See Choosing the right fuel in the Maintenance and Specifications chapter for more information on ethanol.

If the engine fails to start using the preceding instructions (flexible fuel vehicles only) 1. Press and hold down the accelerator 1/3 to 1/2 way to floor, then crank the engine. 2. When the engine starts, release the key, then gradually release the accelerator pedal as the engine speeds up. If the engine still fails to start, repeat Step 1.

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects.

If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell

exhaust fumes.

Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring in fresh air.

USING THE ENGINE BLOCK HEATER (IF EQUIPPED)

To reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater)

adapters.

Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -10°F (-23°C) or below. For best

170

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

results, plug the heater in at least three hours before starting the vehicle. The heater can be plugged in the night before starting the vehicle.

Driving

BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance information for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied. Such noises are usually heard during the first few brake applications in the morning; however, they may be heard at any time while braking and can be aggravated by environmental conditions such as cold, heat, moisture, road dust, salt or mud. If a “metal-to-metal,” “continuous grinding” or “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by an authorized dealer. Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light.

BRAKE

If you are driving down a long or steep hill, shift to a lower gear. Do not apply your brakes continuously, as they may overheat

and become less effective.

Under normal operating conditions, brake dust may accumulate on the wheels. Some brake dust is inevitable as brakes wear and does not contribute to brake noise. The use of modern friction materials with emphasis on improved performance and environmental considerations can lead to more dust than in the past. Brake dust can be cleaned by weekly washing with soapy water and a soft sponge. Heavier deposits can be removed with Motorcraft Wheel and Tire Cleaner (ZC-37–A).

Anti-lock brake system (ABS) This vehicle is equipped with an anti-lock braking system (ABS). A noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and indicates proper functioning of the vehicle’s anti-lock brake system. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized dealer.

171

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.

Using ABS • In an emergency or when maximum efficiency from the four-wheel

ABS is required, apply continuous force on the brake. The four wheel ABS will be activated immediately, thus allowing you to retain steering control of your vehicle and, providing there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop.

• The anti-lock system does not reduce stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop.

• We recommend that you familiarize yourself with this braking

technique. However, avoid taking any unnecessary risks.

ABS

ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately.)

BRAKE

172

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

Parking brake with auto-release (if equipped) Apply the parking brake whenever the vehicle is parked. To set the parking brake: 1. Move the gearshift to P (Park). 2. Push pedal downward.

HOOD

The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released.

BRAKE

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the OFF/LOCK position

and remove the key whenever you leave your vehicle.

The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected. Your vehicle may be equipped with an automatic parking brake release. To release the parking brake: 1. Start the vehicle. 2. Press the brake pedal. 3. Move the gearshift from the P (Park) position to one of the forward gears (the parking brake will not release automatically when you shift into reverse). The brake pedal must remain pressed while the gearshift is moved.

173

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

If the parking brake fails to release after completing this procedure, use the manual parking brake release lever. Pull the lever to manually release the parking brake.

TRACTION CONTROL姟 (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control娂 system. This system helps you maintain the stability and steerability of your vehicle. It is especially useful on slippery and/or hilly road surfaces. The system operates by detecting and controlling wheel spin. The system borrows many of the electronic and mechanical elements already present in the anti-lock braking system (ABS). Wheel-speed sensors allow excess rear wheel spin to be detected by the Traction Control娂 portion of the ABS computer. Any excessive wheel spin is controlled by automatically applying and releasing the rear brakes in conjunction with engine torque reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting. The rear wheels “search” for optimum traction several times a second and adjustments are made accordingly.

Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of an Traction Control娂 event is an indication that at least some of the tires have exceeded their ability to grip the road; this may lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. If you experience a severe road event, SLOW DOWN.

The Traction Control娂 system will allow your vehicle to make better use of available traction on slippery surfaces while you are trying to accelerate or while your foot is on the accelerator pedal. The system is a driver aid which makes your vehicle easier to handle primarily on snow and ice covered roads.

174

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

During Traction Control娂 operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior. If you should become stuck in snow or ice or on a very slippery road surface, try switching the Traction Control娂 system off. This may allow excess wheel spin to “dig” the vehicle out and enable a successful “rocking” maneuver. The traction control indicator flashes during a Traction Control娂 system event. If the traction control indicator comes on and stays lit, either: • the Traction Control娂 system • the customer has disabled the system using the traction control switch

requires service by an authorized dealer, or

located on the left side of the instrument panel.

The Traction Control娂 system will be on every time you turn the ignition key from OFF to ON until you deactivate the system using the traction control switch on the instrument panel left of the steering column.

STEERING

Ford Motor Company recommends that an authorized dealer inspect all steering column assemblies in use in vehicles involved

in a collision. Failure to inspect and if necessary replace the steering column assembly could result in severe injury or death in the event of a collision.

Do not attempt to service, repair, or modify the steering column, its adaptive module, or its fuses. See your authorized dealer.

To prevent damage to the power steering system, never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running.

175

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

(below the MIN mark on the reservoir).

It is also important to maintain a proper power steering fluid level in the power steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level • Some noise is normal during operation. If the noise is excessive, check for low power steering pump fluid level before seeking service by your authorized dealer. • Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by your authorized dealer. • Do not fill the power steering pump reservoir above the MAX mark on

the reservoir, as this may result in leaks from the reservoir.

If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes while driving at a constant vehicle speed, have the power steering system checked by your authorized dealer.

AIR SUSPENSION SYSTEM (IF EQUIPPED) The air suspension system is designed to improve ride, handling and general vehicle performance during: • Certain road conditions • Steering maneuvers • Braking • Accelerations 176

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not operate.

AIR SUSPENSION SWITCH

On vehicles equipped with Air Suspension, turn OFF

the Air Suspension switch prior to jacking, hoisting or towing your vehicle.

Normal vehicle operation does not require any action by the driver.

OFF

INTERRUPTEUR DE LA SUSPENSION PNEUMATIQUE WARNING To prevent sudden vehicle movement, turn off air suspen- sion switch prior to jacking, hoisting or towing vehicle. AVERTISSEMENT Pour prévenir tout mouvement soudain du véhi- cule, placer à l'arrêt l'interrupteur de la suspension pneumatique avant de lever le véhicule (cric ou pont élévateur) ou de le remorquer.

OFF-ARRET

TRACTION-LOK姟 AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok娂 axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a Traction-Lok娂 rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver.

AUTOMATIC TRANSMISSION OPERATION

Brake-shift interlock – column-shift transmission This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter. If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, turn the ignition to 2 (ACC).

177

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

2. Locate the access plug on the underside of the steering column cover.

3. Remove the access plug using a flat head screwdriver. Insert the screwdriver into the access hole nearest the steering wheel. Then push and hold the override button using a flat head screwdriver. Apply the brake pedal and shift the transmission into N (Neutral) while continuing to depress the override button. 4. Reinstall the access plug cover, start the vehicle and release the parking brake.

Do not drive your vehicle until you verify that the brakelamps are working.

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the OFF/LOCK position

and remove the key whenever you leave your vehicle.

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.

See your authorized dealer.

Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless the brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key.

178

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

2. Insert the key and turn it to ACC. Apply the brake pedal and shift to N (Neutral).

When the key is in the ignition and in the ACC position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed. To avoid unwanted vehicle movement, always set the parking brake.

3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter.

Do not drive your vehicle until you verify that the brakelamps are working.

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and

remove the key whenever you leave your vehicle.

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.

See your authorized dealer.

Understanding the gearshift positions of the 4–speed automatic transmission

P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine

179

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park)

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and

remove the key whenever you leave your vehicle.

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position.

O/D OFF

(Overdrive)

The normal driving position for the best fuel economy. Transmission operates in gears one through four.

If your vehicle is equipped with a column-shift transmission, overdrive can be deactivated by pressing the transmission control switch on the gearshift lever. If your vehicle is equipped with a floor-shift transmission, overdrive can be deactivated by pressing the transmission control switch on the gearshift handle.

180

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

The transmission control indicator light (TCIL) will illuminate on the instrument cluster.

O/D OFF

Driving

Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp is illuminated. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears. Examples: city traffic, hilly terrain, heavy loads, trailer towing and when engine braking is required. • To return to O/D (overdrive mode), press the transmission control • O/D (Overdrive) is automatically returned each time the key is turned

switch. The O/D OFF lamp will not be illuminated.

off.

2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slippery roads. • To return to • Selecting 2 (Second) at higher speeds will cause the transmission to

(Overdrive), move the gearshift lever into the

(Overdrive) position.

downshift to second gear at the appropriate vehicle speed.

1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)

when vehicle reaches slower speeds.

Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear.

181

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat.

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).

When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Once through the water, always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. Wet brakes do not stop the vehicle as quickly as dry brakes.

182

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

ROADSIDE ASSISTANCE

Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the New Vehicle Limited Warranty period of three years or 36,000 miles (60,000 km), whichever occurs first on Ford and Mercury vehicles, and four years or 50,000 miles (80,000 km) on Lincoln vehicles.

inflation kit)

responsibility)

Roadside assistance will cover: • a flat tire change with a good spare (except Ford GT which has a tire • battery jump start • lock-out assistance (key replacement cost is the customer’s • fuel delivery – Independent Service Contractors, if not prohibited by state, local or municipal law shall deliver up to 2.0 gallons (7.5L) of gasoline or 5 gallons (18.9L) of diesel fuel to a disabled vehicle. Fuel delivery service is limited to two no-charge occurrences within a 12-month period. • winch out – available within 100 feet (30.5 meters) of a paved or • towing – Ford/Mercury/Lincoln eligible vehicle towed to an authorized dealer within 35 miles (56.3 km) of the disablement location or to the nearest authorized dealer. If a member requests to be towed to an authorized dealer more than 35 miles (56.3 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 miles (56.3 km).

county maintained road, no recoveries.

Trailers shall be covered up to $100 if the disabled eligible vehicle requires service at the nearest authorized dealer. If the trailer is disabled, but the towing vehicle is operational, the trailer does not qualify for any roadside services.

183

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment. In Canada, the card is found in the Owner Information Guide in the glove compartment. U.S. Ford or Mercury vehicle customers who require roadside assistance, call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.

Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your authorized dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our website at www.ford.ca.

HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off.

184

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

• The hazard lights control is

located on top of the steering column.

• Depress hazard lights control to

activate all hazard flashers simultaneously.

• Depress control again to turn the

flashers off.

FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located on the left side of the trunk behind the left rear tail light and the trunk liner.

Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks.

185

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5. Make a further check for leaks in the fuel system.

FUSES AND RELAYS

Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color

15

COLOR

Mini fuses

Grey Violet Pink Tan

Brown

Red Blue Yellow Natural Green

—

Standard

fuses

Grey Violet Pink Tan

Brown

Red Blue Yellow Natural Green

—

Maxi fuses

— — — — — — —

Yellow

—

Green Orange

Cartridge

maxi fuses

— — — — — — — Blue — Pink Green

Fuse link cartridge

— — — — — — — Blue — Pink Green

Fuse rating

2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A

186

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

COLOR

Fuse rating

Mini fuses

Standard

fuses

50A 60A 70A 80A

— — — —

— — — —

Maxi fuses

Red Blue Tan

Natural

Cartridge

maxi fuses Red — — —

Fuse link cartridge

Red Yellow Brown Black

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.

27

18

25

16

26

17

23

14

24

15

21

12

22

13

19

10

20

11

Relay

33

31

29

32

30

28

The fuses are coded as follows.

187

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Passenger Compartment Fuse

Panel Description

Taxi roof lamp, Cluster, Lighting Control Module (Interior Lighting) Ignition (ON) - Electronic Automatic Temperature Control (EATC) module, A/C mode switch (vehicles equipped with manual A/C only), A/C blower relay coil EATC module (vehicles equipped with EATC only) Ignition (ON) - Anti-lock Brake System (ABS) module, Rear Air Suspension Module (RASM), Variable Assist Power Steering (VAPS) Speed control deactivation switch, Stop signal Ignition (ON) - Cluster LCM (Park lamps, Corner lamps) LCM LCM (Switch illumination) Ignition (START) - Audio mute, Police PDB (Police vehicles only) Ignition (ON/ACC) - (window) relay coil (non-Police vehicles only) Ignition (ON/ACC) - (window and decklid) relay coil and Police ON/ACC relay coil (Police vehicles only) Ignition (START) - Starter relay coil, DTRS Ignition (ON/ACC) - Wiper module Ignition (ON) - BTSI (Floor-shift transmission)

Roadside Emergencies

Fuse/Relay Location

Fuse Amp

Rating

10

11

12

13

14

15A

10A

10A

10A

10A

10A 15A 10A 10A 5A

10A

10A

10A

10A

188

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Fuse/Relay Location

15

16
17
18

19
20

21
22

23

24

25

26

27

Fuse Amp

Rating

7.5A

15A 10A 10A

10A 10A

10A 10A

15A

10A

10A

10A

20A

Roadside Emergencies

Passenger Compartment Fuse

Panel Description

Ignition (ON/ACC) - LCM, Door lock switch illumination, Heated seat switch illumination, Moonroof, Overhead console, Electrochromatic mirror Ignition (ON) - Turn signals Ignition (ON/ACC) - Audio Ignition (ON) - A/C mode switch (manual A/C only), Blend door, Heated seat modules LCM (Left-hand low beam) Ignition (ON/START) - Back-up lamps LCM (Right-hand low beam) Ignition (ON/START) - Restraint Control Module (RCM), Occupant Classification Sensor (OCS), Passenger Air bag Deactivation Indicator (PADI) Multi-function switch (Flash-to-pass), LCM (High beams) Ignition (ON/START) - Passive Anti-Theft System (PATS) module, Powertrain Control Module (PCM) relay coil, Fuel relay coil, Ignition coil relay coil Autolamp/Sunload sensor, Power mirrors, Door lock switches, Mirror switch, Keypad switch, Decklid switch, Adjustable pedal switch, DDM Ignition (ON/START) - Cluster, LCM, Overdrive cancel switch, Rear defroster relay coil Cigar lighter, OBD II

189

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Fuse/Relay Location

28

29
30
31

32

33

Fuse Amp

Rating

7.5A

15A 15A 15A 20A 10A

10A

Relay 1

Full ISO relay

Passenger Compartment Fuse

Panel Description

Center High-Mounted Stop Lamp (CHMSL) Audio MFS, Stop lamps Hazards (non-Police vehicles) Hazards (Police vehicles) Mirror heaters, Rear defroster switch indicator Ignition (ON/START), Fire suppression module (if equipped) (Police vehicles only) Rear defroster

Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.

Always disconnect the battery before servicing high current fuses.

To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or

refilling fluid reservoirs.

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.

190

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

503

502

501

24

23

22

20

21

19

304

209

206

208

205

207

301

303

302

204

203

202

201

602

601

118

114

110

106

102

117

113

109

105

101

116

112

108

104

115

111

107

103

18

16

14

12

10

17

15

13

11

The high-current fuses are coded as follows.

Fuse/Relay Location

10
11

Fuse Amp

Rating 25A*

25A*

10A*

20A* 10A*

15A* 30A* 20A* 15A* 20A* 15A*

Power Distribution Box Description Ignition switch (Key in, RUN 1, RUN 2), Hazards Ignition switch (RUN/START, RUN/ACC, START) Powertrain Control Module (PCM) keep alive power Fuel relay feed Rear Air Suspension Module (RASM), VAPS module Alternator regulator PCM relay feed Driver’s Door Module (DDM) Ignition coil relay feed Horn relay feed A/C clutch relay feed

191

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Fuse/Relay Location

12
13
14
15
16
17
18
19
20

21

22

23

24
101
102
103

104

105
106

107

Fuse Amp

Rating 25A* 20A* 20A* 20A* 25A*

— —

15A* 15A*

15A*

20A*

20A*

—

40A** 50A** 50A**

40A**

30A** 40A**

40A**

Power Distribution Box Description Audio Instrument panel power point Stop lamp switch Heated seats Tray lamps (Police vehicles only) Not used Not used Injectors PCM, Mass Air Flow (MAF) sensor, IAT Powertrain loads and sensors, A/C clutch relay coil Police PDB outputs (Police vehicles only) Police PDB outputs (Police vehicles only) Not used Blower relay feed Cooling fan Instrument panel (I/P) fuse box feed #1, I/P fuses 19, 21, 23, 25
and 27
Instrument panel (I/P) fuse box feed #2, I/P fuses 1, 3, 5, 7, 8 and Starter relay feed Anti-lock Brake System (ABS) module (Pump) Rear defroster relay feed

192

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Fuse/Relay Location

108

Fuse Amp

Rating 20A**

109
110
111

112

113

114

115

116

117

118

201
202
203

20A** 30A** 50A**

30A**

40A**

50A**

50A**

50A**

50A**

50A**

50A**

1⁄2 ISO relay

—

1⁄2 ISO relay

Roadside Emergencies

Power Distribution Box Description Moonroof (non-Police vehicles only) Spotlights (available on Police vehicles, Long Wheel Base [LWB] vehicles and commercial vehicles only) ABS module (Valves) Wiper module Police PDB or Police I/P accessory battery feed (Police vehicles only) Air suspension compressor (non-Police vehicles only) Police PDB relay feed (Police vehicles only) Police light bar or Police Trunk accessory battery feed (Police vehicles only) Police PDB or Police I/P accessory battery feed (Police vehicles only) Rear power point or Police trunk accessory battery feed (Police vehicles only) Police I/P accessory battery feed (Police vehicles only) Police PDB or Police I/P accessory battery feed (Police vehicles only) Rear power point or Police trunk accessory battery feed (Police vehicles only) A/C clutch Not used Ignition coil

193

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Fuse/Relay Location

204
205
206
207
208
209
301
302

303
304

501
502
503
601

602

Fuse Amp

Rating

1⁄2 ISO relay

—

1⁄2 ISO relay

— —

1⁄2 ISO relay Full ISO relay Full ISO relay

Full ISO relay Full ISO relay

Diode Diode Diode

20A Circuit

breaker

20A Circuit

breaker

Power Distribution Box Description PCM Not used Fuel Not used Not used Horn Starter Air compressor (non-Police vehicles only) RUN/ACC relay (Police vehicles only) Blower RUN/ACC relay (windows) (non-police vehicles only) RUN/ACC relay (windows and decklid) (police vehicles only) A/C clutch PCM Horn, Door latch Power seats, Lumbar, Decklid (Police vehicles only) RUN/ACC relay (windows) (non-police vehicles only) RUN/ACC relay feed (windows and decklid) (police vehicles only)

* Mini fuse ** Cartridge fuse

Relays Relays are located in the power distribution box and should be replaced by an authorized dealer.

194

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

CHANGING THE TIRES If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Your vehicle may be equipped with a conventional spare tire that is different in one or more of the following: type, brand, size, speed rating and tread design. If this is the case, this dissimilar spare tire is still rated for your vehicle loads (GAWR and GVWR).

The use of tire sealants may damage your tires.

Dissimilar spare tire/wheel information

Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.

If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY” When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the

Safety Compliance Label

195

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

tire

Roadside Emergencies • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire. If 4WD operation is necessary, do not operate above speeds of 10 mph (16 km/h) or for distances above 50 miles (80 km). 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare

tire/wheel

The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) 196

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.

Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving with the full size matching spare tire/wheel, do not exceed 70 mph (113 km/h). It is intended for temporary use only. This means if you need to use it, you should replace it as soon as possible.

Tire change procedure

To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions)

the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.

If the vehicle slips off the jack, you or someone else could be seriously injured.

1. Park on a level surface, activate hazard flashers and set parking brake.

HOOD

197

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel.

3. Remove the spare tire and the jack. The jack could be located: • A — behind the mini spare tire or • B — behind the full size spare

tire

On vehicles equipped with Air Suspension, turn OFF

the Air Suspension switch prior to jacking, hoisting or towing your vehicle.

Refer to Air suspension system in the Driving chapter of the Owner’s Guide for more information. 4. Remove the lug wrench from the jack. Rotate the lug wrench socket out from the handle.

198

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

OFF

Roadside Emergencies

5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle. Insert and twist the handle, then pry against the wheel. 6. If equipped with a full wheelcover, remove the wheelcover center ornament then loosen the five black plastic nuts which retain the wheelcover using the lug wrench. 7. Loosen each wheel metal lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.

Before placing the jack under the vehicle, NOTE the jack location

markings: JACK LOCATION The jack location markings can be found on the lower outer edge of the body. • Locate the jack locator mark (B) on the body (C) near the tire you are changing, then place the jack (D) under the frame (A) of the vehicle aligning it with the mark (B). • Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground.

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

199

Roadside Emergencies

To lessen risk of personal injury, do not put any part

of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is ONLY meant for changing the tire.

• Never use the rear differential

as a jacking point.

8. Remove the metal lug nuts with the lug wrench. 9. Replace the flat tire/wheel assembly with the spare tire/wheel assembly, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 10. Lower the vehicle by turning the jack handle counterclockwise. 11. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 12. For full size spare aluminum wheel, firmly install the center ornament. If equipped with a full size spare tire/wheel assembly and lug nut retained full wheelcover, install the wheelcover by tightening the five black plastic nuts in the order shown on the wheelcover using the lug wrench with about 80 lb. in. (9 N•m) torque. Then firmly install the wheelcover center ornament. 13. Put flat tire, jack and lug wrench away. 14. Turn on the air suspension switch (if equipped).

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).

200

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Bolt size

Wheel lug nut torque*

1⁄2 x 20
* Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.

lb.ft. 100

N•m 135

When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel

or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, resulting in loss of control.

JUMP STARTING

The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or

vehicle damage.

Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.

Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter.

Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system.

201

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off.

Connecting the jumper cables