2006 Ford Crown Victoria Owners Manual

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

4. MUTE: Press to mute the playing media. Press again to return to the playing media or turn the volume control to adjust the volume. 5. Eject: Press to eject CD(s) when the ignition is on or off. Numbers will illuminate in the display indicating which CD slots are loaded with CDs. To eject a specific CD, press eject and the corresponding preset number. If no preset is selected, the system will eject the currently selected CD. Press and hold to eject all loaded discs. Note: If the CD is not removed within 15 seconds, the system will reload the disc and begin play if the system is on. 6. BASS: Press BASS; then to press decrease/increase the level of bass output. TREB (Treble): Press TREB; then press decrease/increase the level of treble output. 7. BAL (Balance): Press BAL; then to shift press sound to the left/right speakers.

SEL-TEXT

SEL-TEXT

SEL-TEXT

to

FADE: Press FADE; then press

SEL-TEXT

to shift sound to

the rear/front speakers.

8. SEL-TEXT: Use with Bass, Treble, Balance, Fade and other menu functions. TEXT: TEXT is only available when equipped with Satellite radio. Your system may be equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit available only in the continental United States.

31

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

to toggle

SEL-TEXT

9. MENU: Press MENU repeatedly to access RDS on/off. Use RDS on/off. Press MENU again to access Program type mode or Show Type mode. (MENU must be pressed within 10 seconds to proceed to the next RDS mode.) The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend that FM radio broadcasters use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. FIND Program type: Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40. With RDS ON, press MENU until the program type menu is displayed. SEL-TEXT One of the various program types will appear. Press to scroll through music types. Press SEEK or SCAN to search for a station playing the requested music category. Show TYPE: Selects between displaying the station’s call letters or music format when RDS is enabled. Press MENU until SHOW XX appears in the display. Press to select NAME or TYPE. Compression: Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press MENU until to enable the compression status is displayed. Press compression feature when COMPRESS OFF is displayed. Press the SEL control again to disable the feature when COMPRESS ON is displayed. When activated, the compression icon will illuminate in the display. Occupancy mode (Available on Audiophile audios only): Press MENU until occupancy mode appears in the display. Press select ALL, DRIVER or REAR SEAT occupancy mode. Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2. Press MENU until AUTOSET appears in the display. Press to toggle ON/OFF. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. When activated, AUTOSET will appear in the display when any of the preset controls are pressed.

SEL-TEXT

SEL-TEXT

SEL-TEXT

to

32

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

SEL-TEXT

SEL-TEXT

to adjust the volume

to increase/decrease the

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting. Press MENU to access and use setting. The level will appear in the display. Setting the clock: Press MENU until SELECT HOUR or SELECT MINS is displayed. Press hours/minutes. Press MENU again to disengage clock mode. 10. Memory presets: To set a station: Select frequency band, tune to a station, press and hold a preset button until sound returns. In CD mode, press to select a specific CD to play. 11. On/Off/Volume: Push to turn on/off; turn to adjust the volume levels. Note: With the ignition off, you may press the volume control to momentarily view the clock. 12. LOAD: Press to load a CD. Press LOAD and a specific preset to load in that particular slot. Available slots are indicated by small flashing indicators in the display. When the system is ready to accept a disc, LOAD CD X will appear in the display. Load the CD. Press and hold to autoload up to 6 discs. Note: Ensure that the system is ready to accept the CD. Do not force the disc into the CD slot as damage could result. 13. AM/FM: Press repeatedly to toggle between AM/FM1/FM2 mode.

14. CD: Press to enter CD mode. Press CD and a preset to select a specific CD to play. 15. SAT: Your system may be equipped with Satellite Ready capability. The kit to enable the Satellite reception is available through your authorized dealer. Detailed satellite instructions are included with the

33

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

dealer installed kit. Dealer installed satellite kit available only in the continental United States. 16. SHUF (Shuffle) /SCAN: Press SCAN to hear a brief sampling of radio stations or CD tracks on the current CD. Press again to stop. SHUF (Shuffle): Press and hold to play the CD tracks in random order for the CD currently being played. Press again to stop.

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from a station, the weaker • Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception. • Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.

the signal and the weaker the reception.

Cassette/player care: Do: • Use only cassettes that are 90 minutes long or less. • Tighten very loose tapes by inserting a finger or pencil into the hole • Remove loose labels before inserting tapes. • Allow tapes which have been subjected to extreme heat, humidity or • Clean the cassette player head with a cassette cleaning cartridge after

cold to reach a moderate temperature before playing.

and turning the hub.

10–12 hours of play to maintain good sound/operation.

Don’t: • Expose tapes to direct sunlight, extreme humidity, heat or cold. • Leave tapes in the cassette player for a long time when not being

played.

34

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

of time.

Don’t: • Expose discs to direct sunlight or heat sources for extended periods • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Dirty, warped or damaged CDs, irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio system warranty and service: Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.

35

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Climate Controls

HI

LO

A/C

MIX

OFF

VENT

NORM

FLOOR

MAX A/C

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Uses recirculated air to cool the vehicle. Air flows from the instrument panel vents only. This mode will help prevent unpleasant odors from entering the vehicle. NORM A/C: Uses outside air to cool the vehicle. Air flows from the instrument panel vents only. VENT: Distributes outside air through the instrument panel vents. OFF: Outside air is shut out and the fan will not operate. FLOOR: Distributes outside air through the floor vents. MIX: Distributes outside air through the windshield defroster vents, floor vents and side window demisters.

: Distributes outside air through the windshield defroster vents and

the side window demisters.

position.

the air flow selector in the

air flow selector in the OFF or MAX A/C position.

Operating tips • To reduce fog build up on the windshield during humid weather, place • To reduce humidity build up inside the vehicle: do not drive with the • Under normal weather conditions, do not leave the air flow selector in MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” using the outside air inlet vents. • Do not put objects under the front seats that will interfere with the • Remove any snow, ice or leaves from the air intake area at the base of

airflow to the back seats.

the windshield.

36

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Climate Controls

To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC) SYSTEM (IF EQUIPPED)

10

11

OUTSIDE TEMP

AUTO

OFF

AUTOMATIC

MAX A/C

NORM A/C

VENT

FLOOR

FLR • DEF

DEF

HI

LO

1. OFF: Outside air is shut out and the fan will not operate.

2. AUTOMATIC: Press AUTOMATIC and select the desired temperature using the temperature controls. The system will automatically determine fan speed, airflow location, and outside or recirculated air to heat or cool the vehicle to the selected temperature. The fan speed will remain automatic unless the thumbwheel is turned.

37

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Climate Controls

3. Fan speed: Turn to manually increase or decrease fan speed.

Distributes outside air through the windshield defroster

4. Defrost: vents and the side window demisters. 5. Floor/defrost: Distributes outside air through the windshield defroster vents, floor vents and the side window demisters. 6. Floor: Distributes outside air through the floor vents. 7. Vent: Distributes outside air through the instrument panel vents. 8. Norm A/C: Uses outside air to cool the vehicle . Air flows from the instrument panel vents only. 9. Max A/C: Uses recirculated air to cool the vehicle. Air flows from the instrument panel vents only. This mode will help prevent unpleasant odors from entering the vehicle. 10. Outside Temp: Press to display the outside temperature. It will remain in the display until pressed again. The temperature will be most accurate when the vehicle is in motion. 11. Temperature control: Press this control to select the temperature. The display window indicates the selected temperature. Fahrenheit/Celsius temperature: Press MAX A/C and DEF simultaneously to toggle between Fahrenheit and Celsius temperature. The set point temperatures in Celsius will be displayed in half-degree increments.

the air flow selector in the

Operating tips • To reduce fog build up on the windshield during humid weather, place • To reduce humidity build up inside the vehicle: do not drive with the • Under normal weather conditions, do not leave the air flow selector in MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” using the outside air inlet vents. • Do not put objects under the front seats that will interfere with the

air flow selector in the OFF or MAX A/C position.

position.

airflow to the back seats.

38

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Climate Controls • Remove any snow, ice or leaves from the air intake area at the base of

the windshield.

To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. A small LED will illuminate when the rear defroster is activated.

The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after a predetermined amount of time or when the ignition is turned to the OFF position. To manually turn off the defroster, press the control again. Activating the rear window defroster will also activate the heated mirrors (if equipped). For more information refer to Heated outside mirrors in the Driver Controls chapter. Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window. This may cause damage to the heated grid lines and will not be covered by your warranty.

39

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

HEADLAMP CONTROL Turns the lamps off.

Turns on the parking

lamps, instrument panel lamps, license plate lamps and tail lamps.

Turns the headlamps on.

Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a predetermined period of time after the ignition switch is turned to OFF. • To turn autolamps on, rotate the control counterclockwise to the next position from OFF.

• To turn autolamps off, rotate the control clockwise past OFF to the

parking lamp position

, then back to OFF.

The headlamps will turn on under the following conditions: 1. Headlamp switch is turned to the “headlamps on position”. 2. With the ignition in ON or START, wipers turned on and the headlamp switch in the autolamp position.

40

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.

Flash to pass Pull toward you slightly to activate and release to deactivate.

Daytime running lamps (DRL) (if equipped) Turns the lowbeam headlamps on with a reduced output. To activate: • the key must be in the ON position, • the parking brake released, and • the headlamp control is in the OFF or parking lamps position.

Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System

does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

41

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate the thumbwheel from left

to right to brighten the instrument panel.

• Rotate the thumbwheel from right

to left to dim the instrument panel.

Domelamp Control The panel dimmer control also controls the domelamp operation. • Rotate the thumbwheel fully to the right, past detent to activate the • In order to turn off the domelamp, rotate the thumbwheel to the left.

domelamp.

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized dealer.

TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn

turn signal.

signal.

The flash rate of the turn signal will speed up considerably if the left or right turn lamp bulb (front or rear) is burned out.

42

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

INTERIOR LAMPS

Lights

Map/Courtesy lamps The courtesy lamps light when: • any door is opened. • the instrument panel dimmer • the UNLOCK control of the

switch is rotated past the detent.

remote entry controls is pressed and the ignition is OFF.

The reading lamps can be turned on by pressing the rocker controls next to each lamp. If equipped with Remote Keyless Entry, the courtesy lamp will illuminate whenever any door is opened and will remain on for 25 seconds after the door is shut or when the ignition is turned to the ON position. With overhead console

With overhead console and moon roof To turn on the map lamps, press the map lamp control.

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

43

Lights

Map/Courtesy lamps The courtesy lamps light when: • any door is opened. • the instrument panel dimmer • the UNLOCK control of the

switch is rotated past the detent.

remote entry controls is pressed and the ignition is OFF.

The reading lamps can be turned on by pressing the rocker controls next to each lamp. If equipped with Remote Keyless Entry, the courtesy lamp will illuminate whenever any door is opened and will remain on for 25 seconds after the door is shut or when the ignition is turned to the ON position. With overhead console

With overhead console and moon roof To turn on the map lamps, press the map lamp control.

44

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

Rear courtesy/reading lamps Rotate the lens to illuminate the lamp. With the lens in the flat position, the courtesy lamp lights when: • Any door is opened. • The panel dimmer thumbwheel is

rotated fully to the right past detent.

BULB REPLACEMENT

Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation.

Replacing exterior bulbs Check the operation of all the bulbs frequently.

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time. Function Headlamp Park lamp and turn lamp (front) Side marker (front) Tail, stop, turn (rear) Side marker (rear) Backup lamp

Trade Number 9007
3457 AK (amber) 194 AK (amber) 3157K 194
3156K

45

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

Function License plate lamp High-mount brakelamp Luggage compartment lamp Rear reading lamp Map lamp Dual floorwell lamp Glove compartment Visor vanity lamp - Slide on Rail system (SOR) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer.

Trade Number 168
912
212-2
578
906
906
168

37

Replacing the interior bulbs Check the operation of all bulbs frequently. Overhead console lamps To remove and replace the lamps in the overhead console: 1. Make sure the headlamp switch is in the OFF position and remove the overhead console from the headliner by pulling it straight down. 2. Remove the bulb socket from the back of the lamp housing by pulling it straight out. 3. Remove the bulb from the socket by pulling straight out.

Install the new bulb in reverse order.

Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. Remove the radiator cover by turning the three knobs to the unlock position. 3. Remove two retainers and pull headlamp assembly forward to expose bulb.

46

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

4. Disconnect the electrical connector from the bulb by pulling rearward.

5. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb. 6. Without turning, remove the old bulb from the lamp assembly by gently pulling it straight back out of the lamp assembly.

To install the new bulb:

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 1. With the flat side of the new bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. Turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly. When the grooves are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 2. Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating it clockwise until you feel a “stop.” 3. Connect the electrical connector into the rear of the plastic base until it snaps, locking it into position. 4. Install the headlamp assembly with two retainers. 5. Install the radiator cover locking it in place with three knobs.

47

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

6. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Replacing front parking lamp/turn signal bulbs The park/turn lamp bulbs can be replaced without removing the headlamp assembly. 1. Make sure headlamp switch is in the OFF position, then open the hood. 2. Remove the radiator cover by turning the three knobs to the unlock position. 3. Remove the screw from the outside of the lamp. 4. Remove the nut from inside the lamp and pull the lamp assembly forward. 5. Disconnect the electrical connector from the bulb by pulling rearward. 6. Rotate the bulb socket counterclockwise and remove from lamp assembly. 7. Carefully pull bulb straight out of the socket and push in the new bulb until it snaps, locking it into position. 8. To complete installation, follow the removal procedure in reverse order. Replacing tail lamp/brake/turn lamp bulbs The tail lamp, the brake lamp and the turn signal lamp bulbs are located in the tail lamp assembly. Follow the same steps to replace either bulb.

48

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

1. Make sure headlamp switch is in OFF position, then open the trunk and remove the pin-type retainer and carefully pull the carpet away to expose the lamp assembly hardware. 2. Remove three nuts and the lamp assembly from the vehicle. 3. Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.

4. Pull the bulb from the socket and push in the new bulb. 5. Install the bulb socket into the lamp assembly by rotating it clockwise. 6. Install the lamp assembly on the vehicle with three nuts ensuring the nuts are flush with the body to prevent water from entering the trunk. 7. Carefully push the carpet back in to place and install the pin-type retainer. Replacing license plate lamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws, grommets and the license plate lamp assembly from the trunk lid. 2. Carefully pull the bulb from the socket and push in the new bulb. 3. Install the lamp assembly on trunk lid with two grommets,

49

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Lights

ensuring the grommets are pushed all the way into the trunk lid and secure with two screws. Replacing backup lamp bulbs 1. Open trunk and remove bulb socket from the trunk lid by turning counterclockwise. 2. Pull the bulb straight out of the socket and push in the new bulb. 3. Install the bulb socket in trunk lid by turning clockwise.

Replacing high-mount brakelamp bulbs 1. Remove two screws from the lamp assembly. 2. Carefully lift the lamp assembly up for access to the bulbs.

3. Carefully pull the bulb socket out of the lamp assembly. 4. Pull the bulb straight out of the socket and push in the new bulb. To install, reverse the removal procedure.

50

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.

Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers

will swipe three times with washer fluid.

• a long push and hold: the wipers and washer fluid will be activated for

up to ten seconds.

Windshield wiper/washer features The exterior lamps will turn on with the ignition on, headlamp control in the Autolamp position and the windshield wipers are turned on.

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.

Never adjust the steering wheel when the vehicle is moving.

51

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp.

Slide on rod feature (if equipped) Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield.

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. These include: • Utility compartment • Power point (inside storage bin) • Cupholders • Air vents to the rear seating positions (heat only)

Use only soft cups in the cupholder. Hard objects can injure you in a collision.

OVERHEAD CONSOLE WITHOUT MOON ROOF (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Some of the features in the overhead console include a compass and HomeLink威. To program the Homelink威, refer to Homelink威 Wireless Control System it this chapter. Electronic compass display (if equipped) Compass: The compass display is contained in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and NW.

52

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass. Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn the ignition to the ON position.

23

15

14
13
12

7 8 9 1011

3. Press and hold the MODE control until VAR appears in the display, then release. The display should show the current zone number. 4. Press the MODE control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated.

Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: 1. Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release. 2. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles. 3. The compass is now calibrated.

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

53

Driver Controls

OVERHEAD CONSOLE WITH MOON ROOF (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Some of the features in the overhead console include Compass, Homelink, and Moon Roof controls.

Compass mode The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. 1. Turn ignition to the ON position. 2. Start the engine. 3. From a blank display press and release the MODE button once. The directional heading will be displayed. Note: If the compass is de-calibrated, CAL will be displayed in the right corner of the display. Refer to “Calibration mode” in this section for more details. 4. The overhead console displays the compass heading in one of eight directions: NORTH, NORTHEAST, EAST, SOUTHEAST, SOUTH, SOUTHWEST, WEST, and NORTHWEST. Zone variation mode Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. A correct zone setting will eliminate compass heading error. To set the compass zone: 1. Press and release the MODE button until the compass directional heading is displayed.

54

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

2. Hold down the MODE button for 5 seconds to enter zone mode. The display will read PRESS RESET TO SET ZONE XX where XX is the current zone. 3. Release the MODE button.

15

14
13
12

23

4. Determine which magnetic zone you are in by referring to the zone map. 5. Repeatedly press and release the RESET button to scroll through the zones 1–15 until the desired zone is displayed. 6. Press the MODE button to save the new zone setting and return to the compass normal mode. Note: The compass exits the zone setting mode and returns to its previous setting after one minute of no activity. Note: If power is interrupted during the zone setting process, the compass resets to the same zone it was set to before the zone change process was started. Calibration mode For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. To calibrate the compass: 1. Press and release the MODE button until the compass directional heading is displayed.

7 8 9 1011

55

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

2. Hold down the MODE button for 10 seconds to enter the calibration mode. The display will read PRESS RESET TO DECAL. 3. Release the MODE button.

4. Press the RESET button to de-calibrate the compass. The display will read CIRCLE SLOWLY TO CALIBRATE for a few seconds and then display a direction with CAL displayed on the right side. 5. Drive the vehicle in a tight circle in a magnetically clean area such as an open parking lot. 6. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]). This will take up to three circles to complete calibration. 7. The correct compass heading will be displayed when the compass is calibrated. Note: If the RESET button is not pressed, the compass will exit calibration mode after three minutes of no activity and the original calibration data will be restored. Note: If power is interrupted during the calibration process, the compass resets to the original calibration data from before the calibration process started. HomeLink姞 wireless control system (if equipped) The HomeLink威 Wireless Control System, located on the overhead console, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting. When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the

56

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed HomeLink威 buttons be erased for security purposes, refer to Programming in this section. Programming Do not program the HomeLink威 with the vehicle parked in the garage. Note: Some vehicles may require the ignition switch to be turned to the second (or “ACC”) position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outside buttons. The message CLEARING CHANNELS will appear on the HomeLink威 display.

• After about 20 seconds, the

message CHANNELS CLEARED will appear.

Do not repeat step one to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威.

57

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your overhead console) while keeping the display in view. 3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. The message CHANNEL “X” (1,2 or 3) TRAINING will appear on the display. Do not release the buttons until step 4
has been completed.

Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents. 4. When the message CHANNEL “X” (1,2 or 3) TRAINED appears on the display, release both the HomeLink威 and hand held transmitter buttons.

• DID NOT TRAIN will be displayed

if the channel did not properly train.

58

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

5. Press and hold the just-trained HomeLink威 button and observe the HomeLink威 house icon on the display. If the indicator light(s) underneath the house icon are constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with step 2 in the “Programming” section — do not repeat step 1. If the indicator light(s) underneath the house icon blink rapidly for two seconds and then turn to a continuous light, proceed with steps 6
through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515. Gate operator & Canadian programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing steps 1 and 2 outlined in the “Programming” section, replace step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating.

59

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls • Continue to press and hold the HomeLink威 button (note step 3
in the “Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The message CHANNEL “X” (1,2 or 3) TRAINING will appear on the display.

• Proceed with step 4 in the “Programming” section. Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515. Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outside buttons. The message CLEARING CHANNELS will appear on the HomeLink威 display.

60

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

• After about 20 seconds, the

message CHANNELS CLEARED will appear on the display. Do not hold for longer that 30 seconds. HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with step 2 in the “Programming” section.

Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. DO NOT release the button. The display will read CHANNEL “X” (1,2 or 3) TRANSMIT

2. The display will change to CHANNEL “X” (1,2, or 3) TRAINING after 20 seconds. Without releasing the HomeLink威 button, follow step 2 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

61

Driver Controls

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located under the cup holder and ashtray drawer in the center stack. The auxiliary power point for five passenger vehicles is located in the floor console storage bin. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.

POWER WINDOWS

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

62

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.

One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on the bottom part of the rocker switch and release quickly. Press the rocker switch again to stop.

Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls.

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function. The electrochromic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up.

63

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Do not block the sensor on the backside of the inside rear view mirror since this may impair proper mirror performance.

EXTERIOR MIRRORS

to adjust the left to adjust the right

Power side view mirrors To adjust your mirrors: 1. Select mirror or mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.

Fold-away mirrors Fold the side mirrors in carefully when driving through a narrow space, like an automatic car wash.

(if equipped)

Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

64

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. • Press the right side of the control to adjust the pedals toward you. • Press the left side of the control to adjust the pedals away from you. The adjustment allows for approximately 2.5 inches (65 mm) of maximum travel.

Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h).

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

65

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator equipped) on the instrument cluster will turn on.

light (if

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

Disengaging speed control To disengage the speed control: • Depress the brake pedal Disengaging the speed control will not erase previous set speed. Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h).

66

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET - control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control.

67

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will

not erase your vehicle’s previously set speed.

• Press the speed control OFF

control.

Note: When you turn the speed control or the ignition off, your speed control set speed memory is erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

Audio control features In Radio mode: • Press NEXT to select the next preset station within the current radio band. In Tape mode: • Press NEXT to listen to the next

selection on the tape.

In CD mode: • Press NEXT to listen to the next

track on the disc.

In any mode: • Press VOL + or - to adjust the

volume.

68

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Climate control features • Press TEMP + or - to adjust

temperature.

MOON ROOF (IF EQUIPPED) To vent the moon roof: • Press and hold the control

forward to raise the moon roof to the vent position (when the glass panel is closed).

To open the moon roof: • For one-touch operation, press

the control rearward and release; this will fully open the moon roof.

• To stop one-touch operation at

the desired position, press the control in any direction and release.

To close the moon roof: • Press and hold the control forward. • To close from the vent position, press and hold the control rearward.

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the overhead console, provides a convenient way to replace up to three hand-held

69

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Some vehicles may require the ignition switch to be turned to the second (or “ACC”) position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1
to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威. 2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your overhead console) while keeping the indicator light in view.

70

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents. 4. The indicator light will flash slowly and then rapidly. Release both buttons when the indicator light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.) 5. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with Step 2 in the “Programming” section — do not repeat Step 1. Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous light, proceed with Steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.

71

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2
outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 3 in the

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with Step 4 in the “Programming” section.

Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

72

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 2 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.

73

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Your display can show up to 3 reconfigurable telltales at one time. What ever is displayed in the top left corner has the highest priority. Premium Display Severity Indicator (located under the Message Center): Indicates severity of the information being displayed on the premium display. Red for high severity, amber for medium severity, and non-lit for information only. For example, a door ajar warning would be accompanied by a red indicator, low fuel by an amber indicator, and fuel economy by an absence of the indicator. The indicator always illuminates with the highest severity rating of the warnings displayed.

Selectable features Select Press this control to select functions shown in the INFO menu and SETUP menu.

Reset Press this control to reset functions shown in the INFO menu and SETUP menu.

74

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Info menu This control displays the following control displays: • Trip odometer/Odometer • Distance to Empty • Average Fuel Economy • Instantaneous Fuel Economy Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes or 10 miles(16 km). DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/ 100 km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up

75

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

service stations

Driver Controls • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control (press and hold RESET for 2 seconds in order to reset the function) after setting the speed control to get accurate highway fuel economy readings. Instantaneous fuel economy Select this function from the INFO menu to display your instantaneous fuel economy. This will display your fuel economy as a Bar Graph ranging from to Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows or no bars illuminated. Instantaneous fuel economy cannot be reset. Setup menu Press this control for the following displays:

excellent economy.

poor economy

one

• System Check • Display (odometer/speedometer) • Font Size (normal/large) • Units (English/Metric) • Language • Oil Minder Start Value 76

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. Pressing the SELECT control cycles the message center through each of the systems being monitored. The sequence of the system check report and how it appears in the message center is as follows: 1. OIL LIFE — PRESS RESET IF NEW OIL 2. WASHER FLUID 3. AIR SUSPENSION 4. RECONFIGURABLE TELLTALES — OK — FAILED RED — FAILED AMBER Display Type 1. Select this function from the SETUP menu. 2. Press the SELECT control to change the display.

Font Size 1. Select this function from the SETUP menu. 2. Press the SELECT control to change font size.

77

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the SELECT control to change from English to Metric.

Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the SELECT control cycles the message center through each of the language choices.

Oil Minder Start Value 1. Select this function from the SETUP control for the current display mode.

2. Press the SELECT control to change oil value.

System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems.

78

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into three categories: • They cannot be reset until the condition is corrected. • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been

completed.

Status Warning cannot be reset Warning returns after 10 minutes

This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Door Ajar Coolant over temperature Powertrain malfunction Check fuel cap Check air suspension Low fuel Overdrive ON/OFF Trunk ajar Check compass module Low washer fluid Change engine oil DOOR AJAR. Displayed when a door is not completely closed. POWERTRAIN MALFUNCTION. Displayed when the powertrain is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. COOLANT OVER TEMPERATURE. Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

Warning returns after the ignition key is turned from OFF to ON.

79

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Never remove the coolant reservoir cap while the engine is running or hot.

CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap in the Maintenance and Specifications chapter. CHECK AIR SUSPENSION. Displayed when the air suspension system is not operating properly. If this message is displayed while driving, pull off the road as soon as safely possible. For more information, refer to Air suspension in the Driving chapter. LOW FUEL. Displayed as an early reminder of a low fuel condition. Warning message can be reset by pressing the RESET button, but will return after 10 minutes. If any other button is pressed besides RESET, the message ’’PRESS RESET TO CLEAR’’ will appear in the Message Center. Once this message disappears (after approximately 2 seconds), press RESET to clear the warning. TRUNK AJAR. Displayed when the trunk is not completely closed. OVERDRIVE ON/OFF. Displayed when the overdrive is enabled or disabled. CHECK COMPASS MODULE. Displayed when the compass is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW WASHER FLUID. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. CHANGE ENGINE OIL. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS.

80

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Press and hold the RESET control for 2 seconds and release. Oil life is set to 100% and “OIL LIFE XXX% HOLD RESET IF NEW OIL” is displayed.

2. Press and hold the RESET control for 3 seconds and release. Oil life is set to 100% and “OIL LIFE START VALUE SET TO XXX%” is displayed.

INTERIOR TRUNK CONTROL The remote trunk release control is located on the driver’s door trim panel and can be operated at any time. You can render the switch inoperable by locking the button with your master key.

If equipped with a perimeter alarm system, the remote trunk release control and power door locks will be disabled when the vehicle perimeter alarm system is armed. This control will not work until the vehicle perimeter alarm system is disarmed. Refer to Perimeter Alarm System in the Locks and Security chapter.

81

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POSITIVE RETENTION FLOOR MAT

Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the

brake pedals.

Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.

82

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

ignition and remote trunk release.

KEYS The vehicle is equipped with a master (black) key and valet (gray) key lock system (if equipped with valet feature). • The master key will access the vehicle’s doors, trunk, glove box, • The valet key (if equipped) will access doors and ignition only. Before using the valet key with an attendant, lock the interior trunk control to disable the interior trunk control located on the drivers door, then lock the glove compartment with your master key. Do not hand over the remote entry transmitter or the master key to the valet attendant. For more information, refer to Interior trunk control in the Driver Controls chapter.

POWER DOOR LOCKS

Power door trim switch inhibit This feature disables the power door locks and trunk interior release switches if all doors are closed and the perimeter alarm becomes armed. Once the power door trim switches are disabled, they can only become active when perimeter alarm is disarmed. Press control to unlock all vehicle doors.

Press control to lock all vehicle doors.

Smart locks (if equipped) With the key in any ignition position, and either the driver’s or passenger’s door open, the doors cannot be locked using the power door lock switches.

83

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

The vehicle may still be locked with the key in the ignition, and performing one of the following actions: • Pressing the manual lock button on the door. • Operating the remote entry transmitter (if equipped). • Operating the keyless entry keypad (if equipped). • Operating the driver’s door with a key.

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle.

84

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. The “T” shaped handle will be located either on the luggage compartment door (lid) or inside the luggage compartment near the tail lamps.

Keep vehicle doors and luggage compartment

locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.

On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people or animals to these high

temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

85

2006 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The remote entry system allows you to lock or unlock all vehicle doors without a key.

The remote entry features operate with the ignition in any position, except in the 3 (ON) , with the transmission not in either P (Park) or N (Neutral). If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem.

Unlocking the doors 1. Press lamps will illuminate. 2. Press

and release to unlock the driver’s door. Note: The interior

and release again within five seconds to unlock all the doors.

Locking the doors once to lock all the doors. The doors will lock upon first press. Press again within three seconds to receive confirmation that the Press vehicle was successfully locked. Note: If all vehicle doors are closed , the horn will chirp once and the upon the second press of the parklamps/taillamps will flash once to confirm the successful locking. , if any door is not securely closed the Upon the second press of the horn will chirp twice to warn that successfully locking was not complete. The park/taillamps will NOT flash if any door is ajar.

Opening the trunk