Download PDF Manual

The occupant's back must be as upright as comfort allows and be against the seat back with the seat belt properly


fastened. Feet must be on the floor, e.g., not on the dash, seat or out of the window.


WARNING


No objects or accessory equipment, e.g. dashboard covers, may be placed on, attached to, or installed near the air bag hatch (the area above the glove compartment) or the area affected by airbag deployment (see the illustration on page 19).


There should be no loose articles, e.g. coffee cups, on the floor, seat, or dashboard area. Never try to open the airbag cover on the steering wheel or the passenger's side dashboard. This should only be


done by a trained and qualified Volvo service technician.


Failure to follow these instructions can result in injury to the vehicle occupants.


22 01 Safety


Safety in the passenger compartment


Occupant Weight Sensor


Disabling the passenger's side front airbag Volvo recommends that ALL occupants (adults and children) shorter than 4 feet 7 inches (140 cm) be seated in the back seat of any vehicle with a front passenger side airbag, and be properly restrained for their size and weight. See also the child safety recommendations on page 33.


The Occupant Weight Sensor (OWS) is designed to meet the regulatory requirements of Federal Motor Vehicle Safety Standard (FMVSS) 208 and is designed to disable (will not inflate) the passenger's side front airbag under certain conditions.


The OWS works with sensors that are part of the front passenger's seat and seat belt. The sensors are designed to detect the presence of a properly seated occupant and determine if the passenger's side front airbag should be enabled (may inflate) or disabled (will not inflate).


The OWS will disable (will not inflate) the passenger's side front airbag when:


the front passenger's seat is unoccupied, or has small/medium objects in the front seat, the system determines that an infant is present in a rear-facing infant seat that is installed according to the


the system determines that a small child is present in a forward-facing child restraint that is installed according to


manufacturer's instructions,


the manufacturer's instructions,


the system determines that a small child is present in a booster seat, a front passenger takes his/her weight off of the seat for a period of time, a child or a small person occupies the front passenger's seat.


The OWS uses a PASSENGER AIRBAG OFF indicator lamp which will illuminate and stay on to remind you that the passenger's side front airbag is disabled. The PASSENGER AIRBAG OFF indicator lamp is located in the overhead console, near the base of the rearview mirror.


NOTE


When the ignition is switched on, the OWS indicator light will go on for up to 10 seconds while the system performs a self-diagnostic test.


However, if a fault is detected in the system:


The OWS indicator light will stay on The SRS warning light (see page 18) will come on and stay on The message PASS. AIRBAG OFF SERVICE URGENT will be displayed in the information display.


WARNING


If a fault in the system is detected and indicated as described, be aware that the passenger's side front airbag will not


deploy in the event of a collision. In this case, the SRS system and Occupant Weight Sensor should be inspected by a trained and qualified Volvo service technician as soon as possible.


23 01 Safety


Safety in the passenger compartment


WARNING


Never try to open, remove, or repair any components in the OWS system. This could result in system malfunction.


Maintenance or repairs should only be carried out by an a trained and qualified Volvo service technician.


The front passenger's seat should not be modified in any way. This could reduce pressure on the seat cushion,


which might interfere with the OWS system's function.


1Volvo recommends that children always be properly restrained in appropriate child restraints in the rear seats. Do not assume that the passenger's side front airbag is disabled unless the PASSENGER AIRBAG OFF indicator lamp is lit. Make sure the child restraint is properly installed. If there is any doubt as to the status of the passenger's side front airbag, move the child restraint to the rear seat.


The OWS is designed to enable (may inflate) the passenger's side front airbag anytime the system senses that a person of adult size is sitting properly in the front passenger's seat. The PASSENGER AIRBAG OFF indicator lamp will be off and remain off.


If a person of adult size is sitting in the front passenger's seat, but the PASSENGER AIRBAG OFF indicator lamp is on, it is possible that the person isn't sitting properly in the seat. If this happens:


Turn the vehicle off and ask the person to place the seatback in an upright position. Have the person sit upright in the seat, centered on the seat cushion, with the person's legs comfortably extended. Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to


detect that person and enable the passenger's frontal airbag.


If the PASSENGER AIRBAG OFF indicator lamp remains on even after this, the person should be advised to ride


in the rear seat.


This condition reflects limitations of the OWS classification capability. It does not indicate OWS malfunction.


24 01 Safety


Safety in the passenger compartment


Modifications If you are considering modifying your vehicle in any way to accommodate a disability, for example by altering or adapting the driver's or front passenger's seat(s) and/or airbag systems, please contact Volvo at:


In the USA:


Volvo Cars of North America, LLC Customer Care Center P.O. Box 914 Rockleigh, New Jersey 07647-0914
1-800-458-1552


In Canada:


Volvo Cars of Canada Corp. National Customer Service 175 Gordon Baker Road North York, Ontario M2H 2N7
1-800-663-8255


WARNING


No objects that add to the total weight on the seat should be placed on the front passenger's seat. If a child is seated in the front passenger's seat with any additional weight, this extra weight could cause the OWS system to enable the airbag, which might cause it to deploy in the event of a collision, thereby injuring the child.


The seat belt should never be wrapped around an object on the front passenger's seat. This could interfere with the


OWS system's function.


The front passenger's seat belt should never be used in a way that exerts more pressure on the passenger than


normal. This could increase the pressure exerted on the weight sensor by a child, and could result in the airbag being enabled, which might cause it to deploy in the event of a collision, thereby injuring the child.


WARNING


Keep the following points in mind with respect to the OWS system. Failure to follow these instructions could


adversely affect the system's function and result in serious injury to the occupant of the front passenger's seat:


The full weight of the front seat passenger should always be on the seat cushion. The passenger should never lift him/herself off the seat cushion using the armrest in the door or the center console, by pressing the feet on the floor, by sitting on the edge of the seat cushion, or by pressing against the backrest in a way that reduces pressure on the seat cushion. This could cause OWS to disable the front, passenger's side airbag.


Do not place any type of object on the front passenger's seat in such a way that jamming, pressing, or squeezing


occurs between the object and the front seat, other than as a direct result of the correct use of the Automatic Locking Retractor/Emergency Locking Retractor (ALR/ELR) seat belt (see page 33).


No objects should be placed under the front passenger's seat. This could interfere with the OWS system's function.


25 01 Safety


Safety in the passenger compartment


Side impact protection (SIPS) airbags


Side impact airbags - front seats only As an enhancement to the structural side impact protection built into your vehicle, it is also equipped with Side Impact Protection System (SIPS) airbags.


The SIPS airbag system is designed to help increase occupant protection in the event of certain side impact collisions. The SIPS airbags are designed to deploy only during certain side-impact collisions, depending on the crash severity, angle, speed and point of impact.


NOTE


SIPS airbag deployment (one airbag) occurs only on the side of the vehicle affected by the impact. The airbags are not designed to deploy in all side impact situations.


SIPS airbag deployment (one airbag) occurs only on the side of the vehicle affected by the impact. The airbags are not designed to deploy in all side impact situations.


Components in the SIPS airbag system


This SIPS airbag system consists of a gas generator, the side airbag modules built into


26 01 Safety


Safety in the passenger compartment


the outboard sides of both front seat backrests, and electronic sensors/wiring.


WARNING


The SIPS airbag system is a supplement to the structural Side Impact Protection System and the three-point seat


belt system. It is not designed to deploy during collisions from the front or rear of the vehicle or in rollover situations.


The use of seat covers on the front seats may impede SIPS airbag deployment. No objects, accessory equipment or stickers may be placed on, attached to or installed near the SIPS airbag system


or in the area affected by SIPS airbag deployment.


Never try to open or repair any components of the SIPS airbag system. This should be done only by a trained and


qualified Volvo service technician.


position with the seat belt properly fastened.


In order for the SIPS airbag to provide its best protection, both front seat occupants should sit in an upright


Failure to follow these instructions can result in injury to the occupants of the vehicle in the event of an accident.


27 01 Safety


Safety in the passenger compartment


Volvo Inflatable Curtain (VIC)


The Volvo Inflatable Curtain system This system consists of inflatable curtains located along the sides of the roof liners, stretching from the center of both front side windows to the rear edge of the rear side door windows. It is designed to help protect the heads of the occupants of the front seats and the occupant of the outboard rear seating positions in certain side impact collisions.


In certain side impacts, both the Inflatable Curtain (VIC) and the Side Impact Airbag System (SIPS airbag) will deploy. The VIC and the SIPS airbag deploy simultaneously.


NOTE


If the inflatable curtain deploys, it remains inflated for approximately 3 seconds.


WARNING


The VIC system is a supplement to the Side Impact Protection System. It is not designed to deploy during


collisions from the front or rear of the vehicle or in rollover situations.


Never try to open or repair any components of the VIC system. This should be done only by a trained and


qualified Volvo service technician.


Never hang heavy items from the ceiling handles. This could impede deployment of the Inflatable Curtain. The cargo area and rear seat should not be loaded to a level higher than 2 in. (5 cm) below the upper edge of the rear side windows. Objects placed higher than this level could impede the function of the Volvo Inflatable Curtain.


WARNING


In order for the VIC to provide its best protection, both front seat occupants and both outboard rear seat occupants should sit in an upright position with the seat belt properly fastened; adults using the seat belt and children using the proper child restraint system. Only adults should sit in the front seats. Children must never be allowed in the front passenger seat. See page 33 for guidelines. Failure to follow these instructions can result in injury to the vehicle occupants in an accident.


28 01 Safety


Safety in the passenger compartment


Whiplash Protection System - WHIPS


Whiplash Protection System (WHIPS) - front seats only The WHIPS system consists of specially designed hinges and brackets on the front seat backrests designed to help absorb some of the energy generated in a collision from the rear (when the vehicle is rear-ended).


In the event of a collision of this type, the hinges and brackets of the front seat backrests are designed to change position slightly to allow the backrest/head restraint to help support the occupant's head before moving slightly rearward. This movement helps absorb some of the forces that could result in whiplash.


WARNING


The WHIPS system is designed to supplement the other safety systems in your vehicle. For this system to function properly, the three-point seat belt must be worn. Please be aware that no system can prevent all possible injuries that may occur in an accident.


The WHIPS system is designed to function in certain collisions from the rear, depending on the crash severity,


angle and speed.


WARNING


Occupants in the front seats must never sit out of position. The occupant's back must be as upright as comfort allows and be against the seat back with the seat belt properly fastened.


WARNING


If your vehicle has been involved in a rear-end collision, the front seat backrests must be inspected by a trained


and qualified Volvo service technician, even if the seats appear to be undamaged. Certain components in the WHIPS system may need to be replaced.


Do not attempt to service any component in the WHIPS system yourself.


29 01 Safety


Safety in the passenger compartment


WARNING


Boxes, suitcases, etc. wedged behind the front seats could impede the function of the WHIPS system. If the rear seat backrests are folded down, cargo must be secured to prevent it from sliding forward against the


front seat backrests in the event of a collision from the rear. This could interfere with the action of the WHIPS system.


WARNING


Any contact between the front seat backrests and the folded rear seat or a rear-facing child seat could impede the function of the WHIPS system. If the rear seat is folded down, the occupied front seats must be adjusted forward so that they do not touch the folded rear seat.


30 01 Safety


Crash mode


Driving after a collision If the vehicle has been involved in a collision, the text SAFETY MODE SEE MANUAL may appear in the information display. This indicates that the vehicle's functionality has been reduced.


NOTE


This text can only be shown if the display is undamaged and the vehicle's electrical system is intact.


Safety mode is a feature that is triggered if one or more of the safety systems (e.g. front or side airbags, an inflatable curtain, or one or more of the seat belt pretensioners) has deployed. The collision may have damaged an important function in the vehicle, such as the fuel lines, sensors for one of the safety systems, the brake system, etc.


WARNING


Never attempt to repair the vehicle yourself or to reset the electrical system after the vehicle has displayed


SAFETY MODE SEE MANUAL. This could result in injury or improper system function.


Restoring the vehicle to normal operating status should only be done by a trained and qualified Volvo service


After SAFETY MODE SEE MANUAL has been displayed, if you detect the odor of fuel vapor, or see any signs


of fuel leakage, do not attempt to start the vehicle. Leave the vehicle immediately.


technician.


Attempting to start the vehicle If damage to the vehicle is minor and there is no fuel leakage, you may attempt to start the vehicle. To do so:


1. Remove the remote control from the ignition slot.


2. Reinsert the remote in the ignition slot. The vehicle will then attempt to reset Safety mode to normal status.


3. Try to start the vehicle.


Moving the vehicle If the electrical system is able to reset system status to normal (SAFETY MODE SEE MANUAL will no longer be shown in the display), the vehicle may be moved carefully from its present position, if for example, it is blocking traffic. It should, however, not be moved farther than is absolutely necessary.


WARNING


Even if the vehicle appears to be drivable after Safety mode has been set, it should not be driven or towed (pulled by another vehicle). There may be concealed damage that could make it difficult or impossible to control. The vehicle should be transported on a flatbed tow truck to a trained and qualified Volvo service technician for inspection/repairs.


31 01 Safety


Child safety


Children should be seated safely


Volvo recommends the proper use of restraint systems for all occupants including children. Remember that, regardless of age and size, a child should always be properly restrained in a vehicle.


Your vehicle is also equipped with ISOFIX/LATCH attachments, which make it more convenient to install child seats.


Some restraint systems for children are designed to be secured in the vehicle by lap belts or the lap portion of a lap- shoulder belt. Such child restraint systems can help protect children in vehicles in the event of an accident only if they are used properly. However, children could be endangered in a crash if the child restraints are not properly secured in the vehicle. Failure to follow the installation instructions for your child restraint can result in your child striking the vehicle's interior in a sudden stop.


Holding a child in your arms is NOT a suitable substitute for a child restraint system. In an accident, a child held in a person's arms can be crushed between the vehicle's interior and an unrestrained person. The child could also be injured by striking the interior, or by being ejected from the vehicle during a sudden maneuver or impact. The same can also happen if the infant or child rides unrestrained on the seat. Other occupants should also be properly restrained to help reduce the chance of injuring or increasing the injury of a child.


All states and provinces have legislation governing how and where children should be carried in a vehicle. Find out the regulations existing in your state or province. Recent accident statistics have shown that children are safer in rear seating positions than front seating positions when properly restrained. A child restraint system can help protect a child in a vehicle. Here's what to look for when selecting a child restraint system:


It should have a label certifying that it meets applicable Federal Motor Vehicle Safety Standards (FMVSS 213) - or in Canada, CMVSS 213.


Make sure the child restraint system is approved for the child's height, weight and development - the label required by


the standard or regulation, or instructions for infant restraints, typically provide this information.


In using any child restraint system, we urge you to carefully look over the instructions that are provided with the restraint. Be sure you understand them and can use the device properly and safely in this vehicle. A misused child restraint system can result in increased injuries for both the infant or child and other occupants in the vehicle.


When a child has outgrown the child safety seat, you should use the rear seat with the standard seat belt fastened. The best way to help protect the child here is to place the child on a cushion so that the seat belt is properly located on the hips (see the illustration on page 41). Legislation in your state or province may mandate the use of a child seat or cushion in combination with the seat belt, depending on the child's age and/or size. Please check local regulations.


A specially designed and tested booster cushion (not available in Canada) can be obtained from your Volvo retailer for children weighing 33 - 80 lb. (15 - 36 kg) and 38-54 inches (97 - 137 cm) in height.


32 01 Safety


Child safety


WARNING


Do not use child safety seats or child booster cushions/backrests in the front passenger's seat. We also recommend


that children under 4 feet 7 inches (140 cm) in height who have outgrown these devices sit in the rear seat with the seat belt fastened.


On hot days, the temperature in the vehicle interior can rise very quickly. Exposure to these high temperatures for


even a short period of time can cause heat-related injury or death. Small children are particularly at risk.


33 01 Safety


Child safety


Automatic Locking Retractor/Emergency Locking Retractor (ALR/ELR)


To make child seat installation easier, each seat belt (except for the driver's belt) is equipped with a locking mechanism to help keep the seat belt taut.


When attaching the seat belt to a child seat: 1. Attach the seat belt to the child seat according to the child seat manufacturer's instructions.


2. Pull the seat belt out as far as possible.


3. Insert the seat belt latch plate into the buckle (lock) in the usual way.


4. Release the seat belt and pull it taut around the child seat.


A sound from the seat belt retractor will be audible at this time and is normal. The belt will now be locked in place. This function is automatically disabled when the seat belt is unlocked and the belt is fully retracted.


WARNING


Do not use child safety seats or child booster cushions/backrests in the front passenger's seat. We also recommend that children who have outgrown these devices sit in the rear seat with the seat belt properly fastened.


Volvo's recommendations Why does Volvo believe that no child should sit in the front seat of a vehicle? It's quite simple really. A front airbag is a very powerful device designed, by law, to help protect an adult.


Because of the size of the airbag and its speed of inflation, a child should never be placed in the front seat, even if he or she is properly belted or strapped into a child safety seat. Volvo has been an innovator in safety for over seventy- five years, and we'll continue to do our part. But we need your help. Please remember to put your children in the back seat, and buckle them up.


Volvo has some very specific recommendations:


Always wear your seat belt. Airbags are a SUPPLEMENTAL safety device which, when used with a three-point seat belt can help reduce


serious injuries during certain types of accidents. Volvo recommends that you do not disconnect the airbag system in your vehicle.


Volvo strongly recommends that everyone in the vehicle be properly restrained. Volvo recommends that ALL occupants (adults and children) shorter than 4 feet 7 inches (140 cm) be seated in the


back seat of any vehicle with a front passenger side airbag.


Drive safely!


34 01 Safety


Child restraint systems


Child restraints


There are three main types of child restraint systems: infant seats, convertible seats, and booster cushions. They are classified according to the child's age and size.


The following section provides general information on securing a child restraint using a three-point seat belt. Refer to pages 42-43 for information on securing a child restraint using ISOFIX lower anchors and/or top tether anchorages.


WARNING


A child seat should never be used in the front passenger seat of any vehicle with a front passenger airbag - not even if the "Passenger airbag off" symbol near the rear-view mirror is illuminated (on vehicles equipped with Occupant Weight Sensor). If the severity of an accident were to cause the airbag to inflate, this could lead to serious injury or death to a child seated in this position.


WARNING


Always refer to the child restraint manufacturer's instructions for detailed information on securing the restraint.


35 01 Safety


Child restraint systems


WARNING


When not in use, keep the child restraint system secured or remove it from the passenger compartment to help


prevent it from injuring passengers in the event of a sudden stop or collision.


A small child's head represents a considerable part of its total weight and its neck is still very weak. Volvo


recommends that children up to age 4 travel, properly restrained, facing rearward. In addition, Volvo recommends that children should ride rearward facing, properly restrained, as long as possible.


36 01 Safety


Infant seats


Securing an infant seat with a seat belt


NOTE


Refer to pages 42-43 for information on securing a child restraint using ISOFIX lower anchors and/or top tether anchorages.


1. Place the infant seat in the rear seat of the vehicle.


2. Attach the seat belt to the infant seat according to the manufacturer's instructions.


3. Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible.


WARNING


An infant seat must be in the rear-facing position only. The infant seat should not be positioned behind the driver's seat unless there is adequate space for safe installation.


WARNING


A child seat should never be used in the front passenger seat of any vehicle with a front passenger airbag - not even if the "Passenger airbag off" symbol near the rear-view mirror is illuminated (on vehicles equipped with Occupant Weight Sensor). If the severity of an accident were to cause the airbag to inflate, this could lead to serious injury or death to a child seated in this position.


37 01 Safety


Infant seats


4. Pull the shoulder section of the seat belt out as far as possible to activate the belt's automatic locking function.


5. Press the infant seat firmly in place, let the seat belt retract and pull it taut. A sound from the seat belt retractor's automatic locking function will be audible at this time and is normal. The seat belt should now be locked in place.


NOTE


The locking retractor will automatically release when the seat belt is unbuckled and allowed to retract fully.


6. Push and pull the infant seat to ensure that it is held securely in place by the seat belt.


WARNING


It should not be possible to move the child restraint more than 1 in. (2.5 cm) in any direction.


The infant seat can be removed by unbuckling the seat belt and letting it retract completely.


38 01 Safety


Convertible seats


Securing a convertible seat with a seat belt


NOTE


Refer to pages 42-43 for information on securing a child restraint using ISOFIX lower anchors and/or top tether anchorages.


Convertible seats can be used in either a forward or rearward-facing position, depending on the age and size of the child.


WARNING


Always use a convertible seat that is suitable for the child's age and size. See the convertible seat manufacturer's recommendations.


1. Place the convertible seat in the rear seat of the vehicle.


2. Attach the seat belt to the convertible seat according to the manufacturer's instructions.


WARNING


A small child's head represents a considerable part of its total weight and its neck is still very weak. Volvo


recommends that children up to age 4 travel, properly restrained, facing rearward. In addition, Volvo recommends that children should ride rearward facing, properly restrained, as long as possible.


Convertible child seats should be installed in the rear seat only. A rear-facing convertible seat should not be positioned behind the driver's seat unless there is adequate space for


safe installation.


39 01 Safety


Convertible seats


3. Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible.


4. Pull the shoulder section of the seat belt out as far as possible to activate the belt's automatic locking function.


5. Press the convertible seat firmly in place, let the seat belt retract and pull it taut. A sound from the seat belt retractor's automatic locking function will be audible at this time and is normal. The seat belt should now be locked in place.


NOTE


The locking retractor will automatically release when the seat belt is unbuckled and allowed to retract fully.


6. Push and pull the convertible seat to ensure that it is held securely in place by the seat belt.


WARNING


It should not be possible to move the child restraint more than 1 in. (2.5 cm) in any direction.


The convertible seat can be removed by unbuckling the seat belt and letting it retract completely.


40 01 Safety


Convertible seats


WARNING


A child seat should never be used in the front passenger seat of any vehicle with a front passenger airbag - not even if the "Passenger airbag off" symbol near the rear-view mirror is illuminated (on vehicles equipped with Occupant Weight Sensor). If the severity of an accident were to cause the airbag to inflate, this could lead to serious injury or death to a child seated in this position.


41 01 Safety


Booster cushions


Securing a booster cushion


1. Booster cushions are recommended for children who have outgrown convertible seats.


2. Place the booster cushion in the rear seat of the vehicle.


3. With the child properly seated on the booster cushion, attach the seat belt to or around the cushion according to the manufacturer's instructions.


Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible.


4. Ensure that the seat belt is pulled taut and fits snugly around the child.


WARNING


The hip section of the three-point seat belt must fit snugly across the child's hips, not across the stomach. The shoulder section of the three-point seat belt should be positioned across the chest and shoulder. The shoulder belt must never be placed behind the child's back or under the arm.


42 01 Safety


ISOFIX lower anchors


Using the ISOFIX lower child seat anchors


Lower anchors for ISOFIX-equipped child seats are located in the rear, outboard seats, hidden below the backrest cushions. Symbols on the seat back upholstery mark the anchor positions as shown. To access the anchors, kneel on the seat cushion and locate the anchors by feel. Always follow your child seat manufacturer's installation instructions, and use both ISOFIX lower anchors and top tethers whenever possible.


To access the anchors 1. Put the child restraint in position.


2. Kneel on the child restraint to press down the seat cushion and locate the anchors by feel.


3. Fasten the attachment on the child restraint's lower straps to the ISOFIX lower anchors.


4. Firmly tension the lower child seat straps according to the manufacturer's instructions.


NOTE


The rear seat's center position is not equipped with ISOFIX lower anchors. When installing a child restraint in this


position, attach the restraint's top tether strap (if it is so equipped) to the top tether anchorage point (see the information on page 43) and secure the restraint with the vehicle's center seat belt (see the information beginning on page 34).


Always follow your child seat manufacturer's installation instructions, and use both ISOFIX lower anchors and top


tethers whenever possible.


WARNING


Be sure to fasten the attachment correctly to the anchor (see the illustration). If the attachment is not correctly


fastened, the child restraint may not be properly secured in the event of a collision.


The ISOFIX lower child restraint anchors are only intended for use with child seats positioned in the outboard


seating positions. These anchors are not certified for use with any child restraint that is positioned in the center seating position. When securing a child restraint in the center seating position, use only the vehicle's center seat belt.


43 01 Safety


Top tether anchors


Child restraint anchorages


Your Volvo is equipped with child restraint top tether anchorages in the rear seat. They are located on the rear side of the backrests.


Securing a child seat 1. Place the child restraint on the rear seat.


2. Route the top tether strap under the head restraint and attach it to the anchor.


3. Attach lower tether straps to the lower ISOFIX/LATCH anchors. If the child restraint is not equipped with lower tether straps, or the restraint is used in the center seating position, follow instructions for securing a child restraint using the Automatic Locking Retractor seat belt (see page 33).


4. Firmly tension all straps.


Refer also to the child seat manufacturer's instructions for information on securing the child seat.


NOTE


On models equipped with the optional cargo area cover, this cover should be removed before a child seat is attached to the child restraint anchors. See page 209.


WARNING


Never route a top tether strap over the top of the head restraint. The strap should be routed beneath the head


restraint.


Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints.


Under no circumstances are they to be used for adult seat belts or harnesses. The anchorages are not able to withstand excessive forces on them in the event of collision if full harness seat belts or adult seat belts are installed to them. An adult who uses a belt anchored in a child restraint anchorage runs a great risk of suffering severe injuries should a collision occur.


Do not install rear speakers that require the removal of the top tether anchors or interfere with the proper use of


the top tether strap.


44 01 Safety


Child restraint registration and recalls


Registering a child restraint


Child restraints could be recalled for safety reasons. You must register your child restraint to be reached in a recall. To stay informed about child safety seat recalls, be sure to fill out and return the registration card that comes with new child restraints.


Child restraint recall information is readily available in both the U.S. and Canada. For recall information in the U.S., call the U.S. Government's Auto Safety Hotline at 1-800-424-9393. In Canada, visit Transport Canada's Child Safety website at http://www.tc.gc.ca/roadsafety/childsafety/menu.htm.


45 01 Safety


Integrated booster cushion


Integrated two-stage booster cushion (option)1


Volvo's optional integrated booster cushion is located in the center seating position. This booster cushion has been specially designed to help safeguard a child seated in the rear seat. This cushion should be stowed (folded up into the rear seat backrest) when not in use. When using an integrated booster cushion, the child must be secured with the vehicle's three-point seat belt.


Use this booster cushion only with children whose weight is between:


Stage 1: 48-80 lbs (22-36 kg) Stage 2: 33-55 lbs 15-25 kg


and whose height is between:


Stage 1: 45-55 in. (115 -140 cm) Stage 2: 37-47 in. (95 -120 cm)


In Canada, Transport Canada's weight recommendation is 40-80 lbs (18-36 kg).


1Canada only: This cushion may be referred to as a built-in booster cushion.


The booster cushion is designed to raise the child higher, so that the shoulder strap crosses over the child's collarbone, not over the child's neck. If using a booster cushion does not result in proper positioning of the shoulder strap, then the child should be placed in a properly secured child restraint (see the information beginning on page 34). The shoulder belt must never be placed behind the child's back or under the arm.


Before driving, check that:


The integrated two-stage booster cushion is set in the correct position for according to the child's height and weight


(see the table below) and is locked in position.


46 01 Safety


Integrated booster cushion


That the seat belt is properly positioned and is taut. The shoulder section of the seat belt is across the child's collarbone, not over the neck. The lap section of the seat belt is across the child's hips and not the abdomen.


Using the integrated booster cushion


Stage 1


Pull the handle (1) forward and upward (2) to release the booster cushion.


Press the booster cushion rearward to lock it in position.


Stage 2


With the booster cushion in the stage 1 position, press the button (see the arrow in illustration 1).


Lift the front edge of the booster cushion and press it rearward toward the backrest to lock it in position.


47 01 Safety


Integrated booster cushion


Stowing the two-stage integrated booster cushion


The booster cushion can be folded down completely (stowed) from either the stage 1 or stage 2 positions.


NOTE


The booster cushion cannot be moved from the stage 2 (upper) position to the stage 1 (lower) position. It must first be folded down completely to the stowed position, and then adjusted to stage 1.


Pull the handle forward to release the booster cushion.


Press down on the center of the booster cushion to return it to the stowed position.


NOTE


The booster cushion must be in the stowed position before the rear seat backrests are folded down.


CAUTION


Be sure there are no loose objects under the booster cushion before it is stowed.


WARNING


DEATH or SERIOUS INJURY can occur


Follow all instructions on the booster cushion and in the vehicle's owner's manual.


MAKE SURE THE BOOSTER CUSHION IS SECURELY LOCKED BEFORE THE CHILD IS SEATED.


Use this booster cushion only with children whose height and weight are within the permitted limits shown in the


table on page 45.


In the event of a collision while the integrated booster cushion was occupied, the entire booster cushion and seat belt must be replaced. The booster cushion should also be replaced if it is badly worn or damaged in any way. This work should be performed by a trained and qualified Volvo service technician only


48 01 Safety


Child safety locks


Child safety locks


Manual child safety locks - rear doors The controls are located on the rear door jambs. Use the remote control's key blade or a screwdriver to adjust these controls.


The rear doors can only be opened from the outside when the slot is in the horizontal position.


The rear doors can be opened from the inside when the slot is in the vertical position.


Power child safety locks (option on certain markets) The power child lock function can be activated by pressing the button shown in the inset illustration above. The ignition must be in mode I or II (see page 80).


When the function is activated, a message will appear in the information display and the indicator light in the button will light up.


With the function activated:


The rear door windows can only be opened with the control in the driver's door. The rear doors cannot be opened from the inside.


NOTE


There are no manual child safety locks on vehicles equipped with the optional power child safety locks.


WARNING


Remember, in the event of an accident, the rear seat passengers cannot open the doors from the inside with the controls in position A (manual child safety locks) or if the power child safety lock function is activated.


49 01 Safety


This page left intentionally blank.


Contents | Top of Page


2 0 0 8
VOLVO


V70


50 02 Locks and alarm Remote key and key blade 52
Keyless drive 61
64
Locks Alarm 66


51 02 Locks and alarm


52 02 Locks and alarm


Remote key and key blade


Introduction


Two remote keys or optional Personal Car Communicators (PCC) are provided with your vehicle. They enable you to unlock the doors and tailgate, and also function as ignition keys to start the vehicle or operate electrical components. The remote keys contain detachable metal key blades for manually locking or unlocking the driver's door and the glove compartment. Up to six remotes can be programmed for use on the same vehicle.


The PCCs have enhanced functionality compared with the standard remote control.


NOTE


In the remainder of this chapter, all references to the remote key also pertain to the PCC unless otherwise stated.


WARNING


Never leave the remote key in the ignition if children are to remain in the vehicle.


Detachable key blade Each remote key or PCC contains a detachable metal key blade for mechanically locking or unlocking the driver's door and the glove compartment, and to enable the private locking function. See page 57 for more information on the key


blade and page 58 for information on the private locking function. The key blades have a unique code, which is used if new ones need to be produced. This code is available at an authorized Volvo retailer.


Loss of a remote key If a remote key is lost, the other one must be taken with the vehicle to a trained and qualified Volvo service technician. As an anti-theft measure, the code of the lost remote must be erased from the system.


The number of registered keys for the vehicle can be found in the vehicle's menu. under Car settings memory


Number of keys. See page 125 for a description of the menu system.


Car key


USA-5WK49264
FCC ID:KR55WK49264 + Siemens VDO 5WK49236
FCC ID:KR55WK49236, 5WK49266 FCC ID:KR55WK49266 + Siemens VDO 5WK49233
FCC ID:KR55WK49233


This device complies with part 15 of the FCC rules and RSS-210. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Canada-5WK49264 IC:267T-5WK49264
+ Siemens VDO 5WK49236
IC:267T-5WK49236, 5WK49266
IC:267T-5WK49266 + Siemens VDO 5WK49233 IC:267T-5WK49233


Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


53 02 Locks and alarm


Remote key and key blade


Key memory - door mirrors and driver's seat The position of the side door mirrors and optional power driver's seat are stored in the remote keys when the vehicle is locked. The next time the driver's door is unlocked with the same remote key and the door is opened within 2 minutes, the power driver's seat and side door mirrors will automatically move to the position that they were in when the doors were most recently locked with the same remote key. See page 83 for more information.


This feature can be activated or deactivated in the vehicle's menu under Car settings mirror positions. See page 125 for a description of the menu system.


Car key memory


Seat &


See also page 61 for information regarding vehicles with the optional keyless drive.


Confirmation when locking/unlocking the vehicle When the vehicle is locked with a remote key, the turn signals will flash once to confirm that this has been completed correctly.


When the vehicle is locked, confirmation will only be given if all of the locks are locked after the doors have been


closed.


NOTE


If you do not receive confirmation when locking the vehicle, check whether a door or the tailgate is ajar, or if this feature has been turned off in the menu.


This function can be activated or deactivated under Car settings settings


Light settings


Unlock confirmation, light. See page 125 for a description of the menu system.


Light settings


Lock confirmation, light, or Car


Immobilizer (start inhibitor) Each of the keys supplied with your vehicle contains a coded transponder. The code in the key is transmitted to an antenna in the ignition slot where it is compared to the code stored in the start inhibitor module. The vehicle will start only with a properly coded key. If you misplace a key, take the other keys to a trained and qualified Volvo service technician for reprogramming as an antitheft measure.


CAUTION


Never use force when inserting the remote key in the ignition slot. The vehicle cannot be started if the transponder is damaged.


USA-FCC ID: LTQWFS 125VO


This device complies with part 15 of the FCC rules. Operation is subject to the following condition: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


54 02 Locks and alarm


Remote key and key blade


Canada-IC: 3659A-WFS125VO


Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


See page 109 for information on starting the vehicle.


Replacing the battery in the remote key The batteries should be replaced if:


The information symbol illuminates and Replace car key battery is shown in the display and/or if the locks do not react after several attempts to unlock or lock the vehicle.


NOTE


The remote key's range is normally approximately 60 ft (20 m) from the vehicle.


See page 60 for information on replacing the battery.


Common functions - Remote key/Personal Car Communicator (PCC)


Lock Unlock Approach lighting Tailgate unlock Panic alarm


Buttons on the remote Lock - Press the Lock button on the remote once to lock all doors and the tailgate. The turn signals will flash once to confirm locking.


Unlock - Press the Unlock button on the remote once to unlock the driver's door. The turn signals will flash twice to confirm unlocking.


After a short pause, press the Unlock button a second time within 10 seconds to unlock the other doors and the tailgate.


This function can be changed so that all doors unlock at the same time under Car settings


lock settings


Doors,


unlock. See page 125 for a description of the menu system.


Approach lighting - As you approach the vehicle, press button parking lights, license plate lighting and the lights in the door mirrors (option).


on the remote control to light the interior lighting,


55 02 Locks and alarm


Remote key and key blade


These lights will switch off automatically after 30, 60 or 90 seconds. See page 125 for more information.


Unlock tailgate- Press the button once to disarm the alarm system and optional movement sensor (the alarm indicator light on the dashboard will go out), and unlock only the tailgate.


NOTE


This function also opens the tailgate on models equipped with the optional power tailgate. As an added safety precaution, the parking lights will come on automatically for a short period when the tailgate


has been opened.


After closing, the tailgate will not automatically relock. Press Lock to relock it and rearm the alarm.


Panic alarm - This button can be used to attract attention during emergency situations.


To activate the panic alarm, press and hold button signals and horn will be activated. The panic alarm will stop automatically after 2 minutes and 45 seconds.


for at least 3 seconds or press it twice within 3 seconds. The turn


To deactivate, wait approximately 5 seconds and press the button again.


Range The remote key has a range of approximately 60 ft. (20 m) from the vehicle.


NOTE


This button will not unlock the vehicle. Buildings or other obstacles may interfere with the function of the remote key. The vehicle can also be locked or


unlocked with the key blade, see page 57.


Functions - PCC


Information button Indicator lights


Pressing the information button


Using the information button 1. Press the information button


provides certain information about the vehicle with the help of the indicator lights


2. All of the indicator lights information from the vehicle. If any of the buttons are pressed during this 7-second period, transmission of


will flash sequentially for approximately 7 seconds to indicate that the PCC is receiving


56 02 Locks and alarm


Remote key and key blade


information to the PCC will be interrupted.


NOTE


If none of the indicator lights flash when the information button has been pressed several times from different places in relation to the vehicle, contact an authorized Volvo service technician.


The indicator lights


provide information according to the illustration below.


Steady green light: the vehicle is correctly locked.


Steady yellow light: the vehicle is not locked.


Steady red light: the alarm has been triggered.


Flashing red lights (Heartbeat sensor): if the two heartbeat sensor lights flash, this indicates that someone may be


inside the vehicle. These lights are only activated if the alarm has been triggered.


Range The PCC's lock and unlock functions have a range of approximately 60 ft. (20 m) from the vehicle.


NOTE


The approach lighting, panic alarm, and the functions controlled by the information button have a range of


approximately 300 ft (100 m) from the vehicle.


Buildings or other obstacles may interfere with the function of the PCC.


Outside of the PCC's range If the PCC is more than approximately 300 ft (100 m) from the vehicle when the information button is pressed, no new information will be received. The PCC most recently used to lock or unlock the vehicle will show the vehicle's most recently received status. The indicator lights will not flash when the information button is pressed while the PCC is out of range.


NOTE


If none of the indicator lights illuminate when the information button is pressed, this may be because the most recent transmission between the vehicle and the PCC was interrupted or impeded by buildings or other objects.


Heartbeat Sensor The heartbeat sensor function 300 ft (100 m) that someone may be in the vehicle. The heartbeat sensor only functions if the alarm has been triggered.


is a complement to the vehicle's standard alarm, and indicates at a distance of up to


NOTE


The heartbeat sensor registers a person's heartbeat in the form of vibrations in the vehicle's chassis. For this reason, the sensor's function may be impaired in areas with high levels of noise or vibrations.


Keyless drive Vehicles equipped with the optional Personal Car Communicator have the keyless drive function. See page 61 for detailed information.


57 02 Locks and alarm


Remote key and key blade


Detachable key blade


The key blade can be removed from the remote control. When removed, the key blade can be used as follows:


To lock/unlock the driver's door To lock/unlock the glove compartment (see page 65) To enable/disable the private locking function (see page 58)


Unlocking the doors with the detached key blade Insert the key blade as far as possible in the driver's door lock. Turn the key blade clockwise approximately one- quarter turn to unlock the driver's door only.


NOTE


After unlocking the driver's door with the key blade, opening the door will trigger the alarm.


To disable the alarm: Insert the remote key in the ignition slot.


Locking the doors with the detached key blade 1. Lock the rear doors and the front passenger's door by pressing the lock button on each door.


2. Turn the key blade one-quarter turn counter-clockwise to lock the driver's door.


Removing the key blade


Slide the spring loaded catch


to the side and pull the key blade out of the remote control


Reinserting the key blade in the remote control 1. Hold the remote control with the slot for the key blade up.


2. Carefully slide the key blade into its groove.


3. Gently press the key blade in the groove until it clicks into place.


58 02 Locks and alarm


Remote key and key blade


Private locking


By utilizing the remote key with the key blade removed, the private locking feature enables you to block access to the glove compartment and disconnect the tailgate from the central locking system for e.g., valet parking or when the


vehicle is brought to the retailer for service.


With the private locking function activated:


The vehicle's doors can be locked or unlocked with the remote The engine can be started The glove compartment cannot be unlocked The tailgate cannot be unlocked or opened with the remote The rear floor hatch cannot be opened


Activating the private locking function 1. Remove the key blade from the remote control.


2. Turn the key blade 180° clockwise in the glove compartment lock to lock the glove compartment and disconnect the tailgate lock from the central locking system. Valet lock activated will appear in the information display.


Deactivating the private locking function Turn the key blade 180° counterclockwise in the glove compartment lock to deactivate private locking.


59 02 Locks and alarm


Remote key and key blade


See page 65 for information on locking the glove compartment normally, without activating the private locking function.


60 02 Locks and alarm


Remote key and key blade


Replacing the battery in the remote key


Opening the remote key/PCC Slide the spring loaded catch


NOTE


to the side and pull the key blade out of the remote control


Turn the remote key with the buttons downward so that the battery does not fall out when the cover is removed.


Insert a small screwdriver in the hole behind the spring loaded catch and carefully pry up the cover


Replacing the batteries


CAUTION


When handling batteries, avoid touching their contact surfaces as this could result in poor battery function in the remote key.


Note the position of the battery's (+) or (-) sides.


Remote key


Use a screwdriver to pry out the old battery. Insert a new one with the + side downward.


PCC


Use a screwdriver to pry out the old batteries.


Insert the first new battery with the + side upward. Insert the plastic spacer over the battery. Insert the second new battery on top of the plastic spacer, with the + side downward.


Re-assembling the remote key 1. Press the remote key's cover into place.


2. Hold the remote control with the slot for the key blade up.


3. Carefully slide the key blade into its groove.


4. Gently press the key blade in the groove until it clicks into place.


Old batteries should be properly recycled.


61 02 Locks and alarm


Keyless drive


Keyless drive (models with Personal Car Communicator only)


Keyless locking and unlocking


This system makes it possible to unlock and lock the vehicle without having to press any buttons on the Personal Car Communicators (PCC). It is only necessary to have a keyless drive remote control in your possession to operate the central locking system.


NOTE


The buttons on the keyless drive remote control can also be used to lock and unlock the vehicle. See page 54 for more information.


Both of the PCCs provided with the vehicle have the keyless function, and additional ones can be ordered. The system can accommodate up to six PCCs.


The red rings in the illustration indicate the area around the vehicle covered by the keyless drive antennas.


Unlocking the vehicle


A keyless drive remote control must be on the same side of the vehicle as the door to be opened, and be within 5


feet (1.5 meters) of the lock or the tailgate(see the shaded areas in the illustration).


Pull a door handle to unlock and open the door or pull the tailgate opening control.


The number of doors that are unlocked at the same time can be set in the vehicle's menu system, under Car settings Lock settings


Keyless entry. See page 125 for a description of the menu system.


NOTE


If the PCC does not function normally (weak battery, etc.), the vehicle can be unlocked with the detachable key blade. See page 57.


Locking the vehicle The doors and the tailgate can be locked by pressing the lock button in any of the outside door handles.


NOTE


On keyless drive vehicles, the gear selector must be in the Park (P) position and the ignition must be switched off before the doors/tailgate can be locked.


Keyless drive remote control and driver's seat/door mirror memory


When you leave the vehicle with a PCC in your possession and lock any door, the position of the driver's seat will


be stored in the seat's memory.


The next time a door is opened by a person with the same PCC in his/her possession, the driver's seat and door


mirrors will automatically move to the position that they were in when the door was most recently locked.


NOTE


If several people carrying PCCs approach the vehicle at the same time, the driver's seat and door mirrors will assume the positions they were in for the person who opens the driver's door.


62 02 Locks and alarm


Keyless drive


See also page 83 for information on adjusting and storing the seat's position in the seat memory.


Keyless drive information messages If anyone leaves the vehicle with the only keyless drive remote control in his or her possession while the ignition is switched on, a message will be shown in the information display and an audible signal will sound.


NOTE


This message will only be displayed if the start control is in mode I or II.


The message will be erased from the display and the audible signal will stop when the PCC has been returned to the vehicle and one of the following has occurred:


A door has been opened and closed The PCC has been inserted in the ignition slot The READ button (see page 126 for the location of this button) has been pressed.


CAUTION


Keyless drive remote controls should never be left in the vehicle. In the event of a break-in, a remote found in the


vehicle could make it possible to start the engine.


Electromagnetic fields or metal obstructions can interfere with the keyless drive system. Avoid placing the remote


control near cellular phones, metallic objects or e.g., in a metal briefcase.


USA - FCC ID:KR55WK48952, KR55WK48964


NOTE


This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.


CAUTION


Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.


Siemens VDO 5WK48891
Tested To Comply With FCC Standards For Automobile Use


63 02 Locks and alarm


Keyless drive


Canada - IC:267T- 5WK48952, 267T- 5WK48964, 267T-5WK48891


NOTE


This device complies with RSS -210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.


CAUTION


Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.


Location of the keyless drive antennas


The keyless drive system has a number of antennas located at various points in the vehicle.


On the inside center of the rear bumper


Left rear door handle


Center of the parcel shelf, on the underside


Ceiling, above the center of the rear seat


Right rear door handle


Under the rear section of the center console


Under the front section of the center console.


WARNING


People with implanted pacemakers should not allow the pacemaker to come closer than 9 inches (22 cm) to any of the keyless drive system's antennas. This is to help prevent interference between the pacemaker and the keyless drive system.


64 02 Locks and alarm


Locks


Locking and unlocking the vehicle


From outside the vehicle The remote key locks all of the doors and the tailgate at the same time.


The first press on the unlock button unlocks the driver's door first, and a second press unlocks the other doors and the tailgate (see also page 54).


NOTE


The vehicle cannot be locked if a door is open.


From inside the vehicle


The lock buttons on the door panel can be used to lock or unlock all doors and the tailgate at the same time.


Unlocking Press the unlock button.


Locking Press the lock button after the front doors have been closed.


Each door can be locked individually with the lock button on the respective doors. The door must be closed first. The door can be unlocked and opened by pulling on the door handle twice.


Automatic relocking If the doors are unlocked, the locks will automatically reengage (re-lock) and the alarm will rearm after 2 minutes unless a door or the tailgate has been opened.


Automatic locking When the vehicle starts to move, the doors and tailgate can be locked automatically. This feature can be turned on or off under Car settings Doors automatic lock. See page 125 for a description of the menu system.


Lock settings


65 02 Locks and alarm


Locks


Glove compartment


The glove compartment can only be locked and unlocked using the detachable key blade in the remote key. See page 57 for information on removing the key blade from the remote key.


Unlock the glove compartment by turning the key a quarter of a turn (90°) counterclockwise. The key slot is


vertical when the glove compartment is unlocked.


Lock the glove compartment by turning the key a quarter of a turn (90°) clockwise. The key slot is horizontal when


the glove compartment is locked.


Locking/unlocking the tailgate


Unlocking the tailgate with the remote key Press the tailgate unlock button on the remote. See also page 54.


The alarm indicator light on the dashboard will go out to indicate that the alarm is not monitoring the entire vehicle. The accessory movement and inclination sensors will be automatically disconnected.


When the tailgate is closed again, it will relock, and all alarm functions will be reactivated.


Locking the tailgate with the remote key Press the lock button on the remote. See also page 54.


Unlocking the tailgate from inside the vehicle


Press the button on the lighting panel


to unlock (but not open1) the tailgate.


NOTE


The taillights will illuminate automatically for a short period when the tailgate has been opened.


1This button also opens, but does not close, the tailgate on models equipped with the optional power tailgate (see page 203).


66 02 Locks and alarm


Alarm


The alarm system


The alarm is automatically armed whenever the vehicle is locked with the remote key or optional Personal Car Communicator.


When armed, the alarm continuously monitors a number of points on the vehicle. The following conditions will trigger the alarm:


The hood is forced open. The tailgate is forced open. A door is forced open. The ignition slot is tampered with An attempt is made to start the vehicle with a non-approved key (a key not coded to the car's ignition). If there is movement in the passenger compartment (if the vehicle is equipped with the accessory movement sensor). The vehicle is lifted or towed (if the vehicle is equipped with the accessory inclination sensor) The battery is disconnected (while the alarm is armed). The siren is disconnected when the alarm is disarmed.


A message will appear in the information display if a fault should occur in the alarm system. Contact an authorized Volvo service technician.


NOTE


Do not attempt to repair any of the components in the alarm system yourself. This could affect the insurance policy on the vehicle.


The alarm indicator light


The status of the alarm system is indicated by the indicator light on the dashboard (see illustration):


Indicator light off - the alarm is not armed The indicator light flashes at one-second intervals - the alarm is armed The indicator light flashes rapidly before the remote key is inserted in the ignition slot - the alarm has been


triggered.


Arming the alarm


Press the Lock button on the remote key. One long flash of the turn signals will confirm that the alarm is armed.


Alarm confirmation settings can be changed under Car settings description of the menu system.


Lock settings


Keyless entry. See page 125 for a


USA FCC ID: MAYDA 5823(3)


This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Canada IC: 4405A-DA 5823(3)


Movement sensor DA5823 by Dynex Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


67 02 Locks and alarm


Alarm


Disarming the alarm


Press the Unlock button on the remote key. Two short flashes from the car's direction indicators confirm that the alarm has been deactivated and that all doors are unlocked.


Turning off (stopping) the alarm


If the alarm is sounding, it can be stopped by pressing the Unlock button on the remote control or by inserting the remote key in the ignition slot. Two short flashes from the car's direction indicators confirm that the alarm has been turned off.


Other alarm-related functions


Automatic re-arming If the doors are unlocked, the locks will automatically reengage (re-lock) and the alarm will re-arm after 2 minutes unless a door or the tailgate has been opened.


Audible/visual alarm signal


An audible alarm signal is given by a battery powered siren. The alarm cycle lasts for 30 seconds. The visual alarm signal is given by flashing all turn signals for approximately 5 minutes or until the alarm is turned


off.


Remote key not functioning If the remote key is not functioning properly, the alarm can be turned off and the vehicle can be started as follows:


1. Open the driver's door with the key blade. This will trigger the alarm.


2. Insert the remote key into the ignition slot. This will turn off the alarm.


68 02 Locks and alarm


Alarm


Reduced alarm function


Turning off the accessory alarm sensor(s)


In certain situations it may be desirable to turn off the accessory inclination and movement alarm sensors if, for example, you drive your vehicle onto a ferry where the rocking of the boat could trigger the alarm or if a pet is left in the vehicle with the doors locked.


Turning off the alarm sensors with the button


Press the button shown in the illustration (within 1 minute after the ignition has been switched off).


The indicator light in the button will remain on until the vehicle is locked. A message will be also be displayed for 10
seconds or until the vehicle is locked, indicating that the sensors are disconnected.


Turning off the alarm sensors using the menu Certain models are not equipped with a button for turning off the accessory alarms sensors. On such models, the vehicle's menu system is used for this purpose (see page 125 for a description of the menu system).


To turn off the sensors:


1. Go into the menu under Car settings.


2. Select Reduced guard (Use the Enter button to make the selection).


NOTE


The accessory sensors are automatically reconnected to the alarm system the next time the vehicle is unlocked and then locked again.


69 02 Locks and alarm


This page left intentionally blank.


Contents | Top of Page


2 0 0 8
VOLVO


V70


70 03 Your driving environment 72
Instruments and controls 80
Ignition modes 82
Seats 87
Steering wheel 89
Lighting 96
Wipers and washers 99
Power windows 101
Mirrors Power moonroof 103
HomeLink® Universal Transceiver (option) 105
Starting the engine 109
112
Transmission 115
Brakes Hill Descent Control (HDC) 117
119
Electric parking brake


71 03 Your driving environment


72 03 Your driving environment


Instruments and controls


Instrument overview


73 03 Your driving environment


Instruments and controls


74 03 Your driving environment


Instruments and controls


Information displays


The information displays computer and messages. The information is shown with text and symbols.


show information on some of the vehicle's functions, such as cruise control, the trip


More detailed information can be found in the descriptions of the functions that use the information displays.


Gauges


Speedometer


Fuel gauge, see also the section on refueling beginning on page 197.


The tachometer shows engine speed in thousands of revolutions per minute (rpm). Do not drive continuously with the needle in the red area of the gauge. The engine management system will automatically prevent excessively high engines speeds. This will be noticeable as a pronounced unevenness in engine speed.


Indicator, information, and warning symbols


Indicator and information symbols


Indicator and warning symbols


High beam and turn signal indicators


Function check All indicator and warning symbols light up in ignition mode II or when the engine is started. When the engine has started, all the symbols should go out except the parking brake symbol, which only goes out when the brake is disengaged.


If the engine does not start or if the function check is carried out in ignition mode II, all symbols go out after 5
seconds except the


75 03 Your driving environment


Instruments and controls


symbol for faults in the vehicle's emissions system and the symbol for low oil pressure.


Certain symbols may not have their functions illustrated, depending on the vehicle's equipment.


Indicator and warning symbols


Trailer turn signal indicator


If you are towing a trailer, this light will flash simultaneously with the trailer's turn signals. If the light does not flash, or if they flash faster than usual when signaling a turn, the turn signals on the trailer or on the vehicle are not functioning properly.


Malfunction Indicator Light


As you drive, a computer called On-Board Diagnostics II (OBDII) monitors your vehicle's engine, transmission, electrical and emission systems.


The malfunction indicator (CHECK ENGINE) light will illuminate if the computer senses a condition that potentially may need correcting. When this happens, please have your vehicle checked by a trained and qualified Volvo service technician as soon as possible.


A malfunction indicator (CHECK ENGINE) light may have many causes. Sometimes, you may not notice a change in your car's behavior. Even so, an uncorrected condition could hurt fuel economy, emission controls, and drivability. Extended driving without correcting the cause could even damage other components in your vehicle.


Canadian models are equipped with this symbol:


Anti-lock Brake System (ABS) warning light


If the warning light comes on, there may be a malfunction in the ABS system (the standard braking system will still function). Check the system by:


1. Stopping in a safe place and switching off the ignition.


76 03 Your driving environment


Instruments and controls


2. Restart the engine.


3. If the warning light goes off, no further action is required.


If the warning light remains on, the vehicle should be driven to a trained and qualified Volvo service technician for inspection. See page 115 for additional information.


Canadian models are equipped with this symbol:


Rear fog light


This symbol indicates that the rear fog light (located in the driver's side tail light cluster) is on.


Stability system


This indicator symbol flashes when the DSTC (Dynamic Stability and Traction Control system) is actively working to stabilize the vehicle. See page 153 for more detailed information.


Tire pressure monitoring system (TPMS) - option


This symbol illuminates to indicate that tire pressure in one or more tires is low. See page 252 for detailed information.


Low fuel level


When this light comes on, there are approximately 2.1 US gallons (8 liters) of fuel remaining in the tank.


Information symbol


The information symbol illuminates and a text message is displayed if a fault is detected in one of the vehicle's systems. The message can be erased and the symbol can be turned off by pressing the READ button (see page 126 for information) or this will take place automatically after a short time (the length of time varies, depending on the function affected).


The information symbol may also illuminate together with other symbols.


High beam indicator


This symbol illuminates when the high beam headlights are on, or if the high beam flash function is used.


Left turn signal indicator


Right turn signal indicator


NOTE


Both turn signal indicators will flash when the hazard warning flashers are used. If either of these indicators flash faster than normal, the direction indicators are not functioning properly.


Indicator and warning symbols


Low oil pressure


If the light comes on while driving, stop the vehicle, stop the engine immediately, and check the engine oil level. If the oil level is normal and the light stays on after restart, have the vehicle towed to the nearest trained and qualified Volvo service technician. This is normal, provided it goes off when the engine speed is increased.


Parking brake applied


This symbol illuminates when the parking brake is applied. On models


77 03 Your driving environment


Instruments and controls


equipped with the electric parking brake, this symbol flashes while the brake is being applied and then glows steadily.


A flashing symbol means that a fault has been detected. See the message in the information display.


Canadian models are equipped with this symbol:


NOTE


This symbol also comes on when the mechanical parking brake is only slightly applied.


Airbags - SRS


If this light comes on while the vehicle is being driven, or remains on for longer than approximately 10 seconds after the vehicle has been started, the SRS system's diagnostic functions have detected a fault in a seat belt lock or pretensioner, a front airbag, side impact airbag, and/or an inflatable curtain. Have the system(s) inspected by a trained and qualified Volvo service technician as soon as possible.


Seat belt reminder


This symbol comes on for approximately 6 seconds if the driver has not fastened his or her seat belt.


Generator not charging


This symbol comes on during driving if a fault has occurred in the electrical system. Contact an authorized Volvo workshop.


Engine temperature Engine overheating can result from low oil or coolant levels, towing or hard driving at high heat and altitude, or mechanical malfunction. Engine overheating will be signaled with text and a red warning triangle in the middle of the instrument display. The exact text will depend on the degree of overheating. It may range from "HIGH ENGINE TEMP - SLOW DOWN" to "HIGH ENGINE TEMP - STOP ENGINE." If appropriate, other messages, such as "COOLANT LEVEL LOW" will also be displayed. If your engine does overheat so that you must stop the engine, always allow the engine to cool before attempting to check oil and coolant levels.


Fault in brake system


If this symbol lights, the brake fluid level may be too low. Stop the vehicle in a safe place and check the level in the brake fluid reservoir, see page 223. If the level in the reservoir is below MIN, the vehicle should be transported to an authorized Volvo workshop to have the brake system checked.


If the brake and ABS symbols come on at the same time, there may be a fault in the brake force distribution system.


1. Stop the vehicle in a safe place and turn off the engine.


2. Restart the engine.


If both symbols extinguish, continue driving. If the symbols remain on, check the level in the brake fluid reservoir. See page 223. If the brake fluid level is


normal but the symbols are still lit, the vehicle can be driven, with great care, to an authorized Volvo workshop to have the brake system checked.


If the level in the reservoir is below MIN, the vehicle should be transported to an authorized Volvo workshop to


have the brake system checked.


WARNING


If the fluid level is below the MIN mark in the reservoir or if a warning message is displayed in the text window:


DO NOT DRIVE. Have the vehicle towed to an authorized Volvo retailer and have the brake system inspected.


If the ABS and Brake system lights are on at the same time, there is a risk of reduced vehicle stability.


78 03 Your driving environment


Instruments and controls


Warning symbol


The red warning symbol comes on when a fault has been indicated which could affect the safety and/or drivability of the vehicle. An explanatory text is shown on the information display at the same time. The symbol remains visible


until the fault has been rectified but the text message can be cleared with the READ button, see page 126. The warning symbol can also come on in conjunction with other symbols.


Action:


1. Stop in a safe place. Do not drive the vehicle further.


2. Read the information on the information display. Implement the action in accordance with the message in the display. Clear the message using READ.


Reminder - doors not closed If one of the doors, the hood or trunk lid is not closed properly, the information or warning symbol comes on together with an explanatory text message in the instrument panel. Stop the vehicle in a safe place as soon as possible and close the door, hood or tailgate.


If the vehicle is driven at a speed lower than approximately 5 mph (7 km/h), the information symbol comes on.


If the vehicle is driven at a speed higher than approximately 5 mph (7 km/h), the warning symbol comes on.


Trip odometers


Odometer display


Button for toggling between T1 and T2, and for resetting the odometer.


The trip odometers are used to measure short distances. A short press on the button toggles between the two trip odometers T1 and T2. A long press (more than 2 seconds) resets an active trip odometer to zero. The distance is shown in the display.


79 03 Your driving environment


Instruments and controls


Clock


Display


Control for setting the clock.


Turn the control clockwise/counterclockwise to set the time. The set time is shown in the information display.


80 03 Your driving environment


Ignition modes


Functions


Inserting and removing the remote key The various ignition modes are accessed by inserting the remote key into the ignition slot.


The remote key can be removed from the ignition slot by pressing the key in. It will then be ejected slightly and can be removed from the slot. The gear selector must be in position P (Park).


NOTE


The brake pedal must not be depressed when accessing ignition modes I or II.


CAUTION


Foreign objects in the ignition slot can impair function or damage the lock.


Ignition mode 0
Insert the remote key in the ignition slot.


Ignition mode I Press the remote key into the ignition slot and press START/STOP ENGINE.


Ignition mode II Press the remote key into the ignition slot and press START/STOP ENGINE for approx. 2 seconds.


Ignition mode III (engine start) Start the engine, see page 109.


Stopping the engine Press START/STOP ENGINE. (If the engine is running and the vehicle is moving, keep the button depressed until the engine stops).


Return to ignition mode 0
Press START/STOP ENGINE to return from I, II, or III to ignition mode 0.


NOTE


During towing, ignition mode II should be used so that the lighting can be switched on.


81 03 Your driving environment


Ignition modes


Functions with timer The audio system can be operated without a key for 15 minutes at a time by pressing the POWER button. The power windows work for several minutes after the key has been removed, although not after the door has been opened.


NOTE


Use the POWER button for the audio system when the engine is not running to avoid discharging the battery.


82 03 Your driving environment


Seats


Front seats


Lumbar support: turn the control for firmer or softer lumbar support.


Front-rear adjustment: lift the bar and move the seat to the position of your choice.


Raise/lower front edge of seat cushion, pump up/down.


Backrest tilt: turn the control to adjust the angle of the backrest.


Raise/lower the seat, pump up/down.


Control panel for power seat.


WARNING


Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. In


addition, position the seat as far rearward as comfort and control allow.


Check that the seat is securely locked into position after adjusting.


Folding the front seat backrest


The front passenger seat backrest can be folded to a horizontal position to make room for a long load. Fold the backrest as follows:


Move the seat as far back as possible.


Adjust the backrest to an upright position.


Lift the catches on the rear of the backrest.


Without releasing the catches, push the backrest forward.


Move the seat as far forward as possible so that the head restraint slides under the glove compartment.


WARNING


Cover sharp edges on the load to help prevent injury to occupants. Secure the load to help prevent shifting during sudden stops.


83 03 Your driving environment


Seats


Power seat (option)


Front edge of seat cushion up/down


Seat forward/backward and up/down


Backrest tilt


Operation The seats can be adjusted for a short period after unlocking the door with the remote control without the key in the ignition slot. Seat adjustment is normally made when the ignition is on and can always be made when the engine is running.


NOTE


Only one of the power seat's controls can be used at the same time. The power seats have an overload protector that activates if a seat is blocked by any object. If this occurs, switch


off the ignition (key in position 0) and wait for a short period before operating the seat again.


Seat with memory function (option)


Stored seat position


Stored seat position


Stored seat position


Memory button


Programming the memory Three different seating and door mirror positions can be stored in the driver seat's memory.


The following example explains how button 1 can be programmed. Buttons 2 and 3 can be programmed in the same way.


To program (store) a seat position and door mirror position in button 1:


1. Move the seat (and door mirrors) to the desired position using the seat and mirror adjustment controls.


2. Press and hold down the M (memory) button.


3. With the memory button depressed, press the button 1 briefly to store the current position for the seat/mirrors.


To move the seat and mirrors to the position that they were in when a button was programmed:


1. Press and hold down button 1 until the seat and mirrors stop moving.


NOTE


As a safety precaution, the seat will stop automatically if the button is released before the seat has reached the preset position.


84 03 Your driving environment


Seats


Remote keyless entry system and the driver's seat The remote control transmitter also controls the position of the power driver's seat in the following way:


1. Adjust the seat to your preferences.


2. When you leave your vehicle, lock it using the remote control.


The position of the driver's seat is now stored in the remote control's memory.


Automatic seat adjustment To move the seat to the position in which you left it:


1. Unlock the driver's door with the same remote control (the one used to lock the doors)


2. Open the driver's door within 2 minutes.


The driver's seat will automatically move to the position in which you left it.


NOTE


The key memory is independent of the seat memory. The seat will Move to this position even if someone else has moved it to a different seating position and locked


the vehicle with a different remote control.


This feature will work in the same way with all of the remote control transmitters that you use with your vehicle.


The function can be activated/deactivated under Car key memory menu system, see the information beginning on page 125.


Seat & mirror positions. For a description of the


Emergency stop If the seat accidentally begins to move, press one of the buttons to stop the seat.


WARNING


Because the driver's seat can be adjusted with the ignition off, children should never be left unattended in the


vehicle.


Movement of the seat can be STOPPED at any time by pressing any button on the power seat control panel. Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. In


addition, position the seat as far rearward as comfort and control allow.


The seat rails on the floor must not be obstructed in any way when the seat is in motion.


Heated/ventilated seats (option) See page 131.


85 03 Your driving environment


Seats


Rear seats


Folding down the rear seat backrests


The three sections of the rear seat backrest can be folded down in different combinations to make it easier to transport long objects.


The left (driver's side) section can be folded down separately. The center section can be folded down separately. The right (passenger's side) section can be folded down together with the center section. All three sections can be folded down together.


Release and lower the center head restraint (see page 86) if the center and/or right section of the backrest is to be


lowered. The outboard head restraints fold down automatically.


Pull up the backrest release control on the respective section(s) and fold the section(s) down.


NOTE


It may be necessary to move the front seats forward or put their backrests in a more upright position before folding down the rear seat backrests.


WARNING


When the backrest(s) are returned to the upright position, check that it is properly locked in place. The red


indicators should not be visible.


Return the outboard head restraints to the upright position. Long loads should always be securely anchored to help avoid injury in the event of a sudden stop. Always turn the engine off and apply the parking brake when loading/unloading the vehicle. Place the transmission in the Park (P) position to help prevent inadvertent movement of the gear selector. On hot days, the temperature in the vehicle interior can rise very quickly. Exposure of people to these high


temperatures for even a short period of time can cause heat-related injury or death. Small children are particularly at risk.


86 03 Your driving environment


Seats


Rear center head restraint


The center head restraint should be adjusted according to the passenger's height. The restraint should be carefully adjusted to support the occupant's head.


Pull the head restraint up as required. To lower, press and hold the button (located at the center, between the backrest and the head restraint) while


pressing the head restrain down.


WARNING


The center rear seat head restraint should only be in its lowest position when this seat is NOT occupied. When the center position is occupied, the head restraint should be correctly adjusted to the passenger's height.


Manually lowering the rear seat's outboard head restraints


Pull the handle closest to the head restraint to fold it down. To return the head restraint to the upright position, push it up until it clicks into place.


NOTE


The head restraint must be returned to the upright position manually.


WARNING


For safety reasons, no one should be allowed to sit in the outboard rear seat positions if the head restraints are folded down. If these positions are occupied, the head restraints should be in the upright (fixed) position.


87 03 Your driving environment


Steering wheel


Adjusting


Lever for releasing/locking the steering wheel


Possible positions


The steering wheel can be adjusted for both height and reach:


1. Pull the lever toward you to release the steering wheel.


2. Adjust the steering wheel to the position that suits you.


3. Push back the lever to fix the steering wheel in place. If the lever is difficult to push into place, press the steering wheel lightly at the same time as you push the lever.


WARNING


Never adjust the steering wheel while driving.


With speed-dependent power steering (option) the level of steering force can be adjusted, see page 155.


Keypads


Cruise control, see page 156


Adaptive cruise control (option), see page 158.


Audio controls, see page 124.


88 03 Your driving environment


Steering wheel


Horn


Press the steering wheel hub to sound the horn.


89 03 Your driving environment


Lighting


Lighting panel


Thumb wheel for adjusting display and instrument lighting


Rear fog light


Front fog lights


Headlights/parking lights


Instrument lighting Illumination of the display and instrument lights will vary, depending on ignition mode.


The display lighting is automatically subdued in darkness and the sensitivity is set with the thumb wheel.


The intensity of the instrument lighting is adjusted with the thumb wheel.


High/low beam headlights


Low beams When the engine is started, the low beams are activated automatically (daytime running lights) if the headlight control is in position


or


Daytime running lights can be deactivated by an authorized Volvo workshop.


NOTE


The use of daytime running lights is mandatory in Canada. Continuous high beams cannot be activated when the headlight switch is in position


or


. High beam


flash will function in these positions.


High beam flash Move the lever toward the steering wheel to position


. The high beams come on until the lever is released.


High/low beam headlights Continuous high beams Set the ignition to mode II.


With the light switch in position between high and low beams (this also applies on models equipped with the optional Active Bi-Xenon® headlights).


, pull the turn signal lever toward the steering wheel to position


to toggle


The


symbol illuminates in the instrument panel to indicate that the high beams are on.


90 03 Your driving environment


Lighting


Active Bi-Xenon® Lights (ABL)-option


When the ABL function is activated, the headlight beams adjust laterally to help light up a curve according to movements of the steering wheel (see the right-pointing beam in the illustration).


This function is activated automatically when the engine is started and can be deactivated/reactivated by pressing the ABL button there is a fault in the system.


in the center console. This button lights up when the ABL function is activated, and will flash if


NOTE


This function is only active in twilight or dark conditions, and only when the vehicle is in motion.


Parking lights


The front and rear parking lights can be turned on even when the ignition is switched off.


Turn the headlight control to the center position (the license plate lighting comes on at the same time).


The lighting also comes on when the trunk lid is opened in order to alert anyone traveling behind your vehicle.


91 03 Your driving environment


Lighting


Brake lights


The brake lights come on automatically when the brakes are applied.


Emergency brake lights (EBL)


Emergency Brake Lights, EBL, activate in the event of sudden braking or if the ABS system is activated. This function causes an additional taillight on each side of the vehicle to illuminate to help alert vehicles traveling behind.


The EBL function activates if:


The ABS system activates for more than approximately a half second In the event of sudden braking while the vehicle is moving at speeds above approximately 6 mph (10 km/h)


When the vehicle has come to a stop, the brake lights and additional taillights remain on for as long as the brake pedal is depressed or until braking force on the vehicle is reduced.


Front fog lights


The front fog lights can be switched on together with high/low beams or the parking lights.


Press the button to switch the fog lights on/off. The light in the button comes on when the fog lights are on.


NOTE


Regulations regarding the use of the front fog lights may vary, depending on where you drive.


92 03 Your driving environment


Lighting


Rear fog light


The single rear fog light is located in the driver's side taillight cluster.


The rear fog light will only function in combination with the high/low beam headlights or the optional front fog lights.


Press the button to switch the rear fog light on/off. The rear fog light indicator symbol and the light in the button come on when the rear fog light is switched on.


on the instrument panel


NOTE


The rear fog light is considerably brighter than the normal tail lights and should be used only when conditions such as fog, rain, snow, smoke or dust reduce visibility for other vehicles to less than 500 ft. (150 meters).


Hazard warning flashers


The hazard warning flasher should be used to indicate that the vehicle has become a traffic hazard. To activate the flashers, press the button in the center dash. Press the button again to turn off the flashers.


Loading...
x