You may also be interested in...

2008 Volvo C70 Owners Manual

Download PDF Manual


NOTE


The indicator light will light up even if the parking brake has only been partially applied.


When applying the parking brake 1. Press firmly on the brake pedal.


2. Pull the parking brake lever up firmly to its full extent.


3. Release the brake pedal and ensure that the vehicle is at a standstill.


4. If the vehicle rolls, the parking brake lever must be pulled more firmly.


5. When parking a vehicle always put the gear selector in first gear (for manual transmission) or P (for automatic transmission).


Parking on a hill


If the vehicle is pointing uphill, turn the front wheels so that they point away from the curb. If the vehicle is pointing downhill, turn the front wheels so that they point toward the curb.


Releasing the parking brake 1. Press firmly on the brake pedal.


2. Pull the lever up slightly, press the button at the end of the lever and lower the lever completely.


WARNING


Pull up the parking brake lever up firmly to its full extent.


66 02 Instruments and controls


12-volt sockets


12-volt socket (front seat)


The 12-volt socket can be used to plug in certain accessories such as cellular telephones, etc. The maximum current is


10A. The key must be in position I (or higher) for the auxiliary socket to function.


Ashtrays/cigarette lighter The auxiliary socket can also be used for a cigarette lighter 1, and ashtrays 1 are also available. Please contact your Volvo retailer.


1 Accessory.


NOTE


The cover should be kept on when the auxiliary socket is not in use.


Auxiliary equipment


The buttons to the left of the 12-volt socket can be used for Volvo-installed optional or auxiliary equipment.


67 02 Instruments and controls


Power windows


Operation


The power windows are opened and closed using the buttons in the armrests, or can be opened by pressing the unlock button on the central locking system's remote control (see page 113).


Opening/closing the windows from inside the car


NOTE


The ignition must be ON (ignition in position I, II or the engine running) for the power windows to function. The power windows will also function after the ignition has been switched off as long neither of the doors has been


opened.


Opening a window


Lightly press down the front edge of any of the buttons (2 or 3) to the first detent ("stop") to open a window to the


position of your choice.


WARNING


Always remove the ignition key when the vehicle is unattended. Never leave children unattended in the vehicle. Make sure that the windows are completely unobstructed before they are operated.


Press down the front part of one or both buttons 3 as far as possible and release to automatically open the front


window(s) completely.


To stop the window at any time, pull the button up.


NOTE


To reduce buffeting wind noise if the rear windows are opened, also open the front windows slightly.


Closing a window


Lightly pull up the front edge of any of the buttons (2 or 3) to the first detent ("stop") to close a window to the


Pull up the front part of one or both buttons 3 as far as possible and release to automatically close the front


position of your choice.


window(s) completely.


All windows Button 1 can be used to open or close all of the windows at the same time.


Briefly press the right side of the button to automatically open all of the windows. Press and hold down the left side of the button to close all of the windows.


68 02 Instruments and controls


Mirrors


Rearview mirror


Auto-dim function An optional integrated sensor reacts to headlights from following traffic and automatically reduces glare.


Rearview mirror with compass (option)


The upper right-hand corner of the rearview mirror has an integrated display that shows the compass direction toward which the car is pointing. Eight different directions can be displayed: N, NE, E, SE, S, SW, W and NW. The display shows your car's orientation with respect to true north.


Calibrating the compass


The compass may need to be calibrated in certain cases. If calibration is required, the character C appears in the mirror's display.


The earth is divided into 15 magnetic zones. The compass is initially set for the zone to which the car was delivered, and should always be adjusted if the car is driven to a new magnetic zone. A "C" will be displayed if calibration becomes necessary.


69 02 Instruments and controls


Mirrors


To calibrate the compass: 1. Stop the car in a large, open area, away from traffic.


2. Using a pen or similar object, hold the button (1) depressed for at least 6 seconds. "C" will be displayed.


3. Press button (1) for at least 3 seconds to display the number of the current magnetic zone.


4. Press button (1) repeatedly until the number for the required geographical area (1-15) is displayed. "C" will be displayed again.


5. Drive slowly in a circle at a maximum speed of 6 m.p.h. (10 km/h) until a compass direction is displayed.


Calibration is complete.


Magnetic zones


70 02 Instruments and controls


Mirrors


Power door mirrors


The mirror control switches are located on the driver's door armrest.


To adjust the mirrors:


Driver's door mirror: Press the L button (a light in the switch will go on) to activate the adjustment control. Use this control to adjust the driver's door mirror.


Passenger's door mirror: Press the R switch (a light in the switch will go on) to activate the adjustment control. Use this control to adjust the passenger's door mirror.


After you have adjusted the mirror(s), press the L or R switch again (the LED will go out) to deactivate the adjustment control.


WARNING


The mirrors should always be adjusted prior to driving. Objects seen in the passenger's side wide-angle door mirror are closer than they appear to be.


Storing the mirrors' position The position of the power door mirrors is stored when the car is locked with the remote control. When the car is unlocked with the same remote control, the mirrors will move to the stored position.


Blind Spot Information System (BLIS) -option The Blind Spot Information System (BLIS) is an information system that indicates the presence of another vehicle in the side-view mirror's "blind area." See page 159 for detailed information.


71 02 Instruments and controls


Personal settings


Control panel


A. Display


B. Menu button


C. Exit button


D. Enter button


E. Menu navigation controls


Personal settings can be made for some of the car's functions, such as the central locking system, climate control, and the audio system. Please refer to page 236 for more information on the audio functions that can be adjusted. The settings are presented in the display (A).


To access the menu and adjust settings: 1. Press MENU (B).


2. Scroll to "Car Settings" using the menu navigation control (E).


3. Press ENTER (D).


4. Select an alternative using the menu navigation control (E).


5. Confirm your selection by pressing ENTER.


To exit the menu:


Press EXIT (C).


Available settings


Clock adjust To set the time:


1. Use the number keys or the up/down arrow keys on the navigation control (E) to change the hour or minute.


2. Select hour(s) or minute(s) to be changed with the left/right arrow keys.


3. Press ENTER to start the clock.


NOTE


If you are currently using the 12-hour time setting, use the up/down arrow keys to select AM/PM after the minute- setting has been adjusted.


Lock confirmation light When the car is locked/unlocked with the remote control, the direction indicators can be selected to flash to confirm the action. The alternatives On/Off are available for both locking and unlocking.


72 02 Instruments and controls


Personal settings


Autolock When the car starts to move, the doors and trunk can be locked automatically. The alternatives On/Off are available.


NOTE


Pulling the handle twice on a door unlocks and opens that door.


Unlock There are two alternatives for unlocking:


Global (All doors)


Unlocks all doors and the trunk with one press on the remote control.


Two Step (Two-stage unlocking)


This alternative unlocks the driver's door with one press on the remote control. A second press unlocks the passenger's door and the trunk.


Operating side windows The following alternative can be selected for opening all windows at the same time by pressing and holding the Unlock button on the central locking system's remote control. See page 113 for more information.


Auto open all windows On/Off


Approach lighting This alternative determines the length of time for which the car's lights will remain on when the Approach light button on the central locking system's remote control is pressed. Intervals of 30/60/90 seconds may be selected. See page 113
for more information.


Home safe lighting This alternative determines the length of time for which the car's lights will remain on when the high beam lever on the steering column is pulled toward the wheel with the ignition switched off. Intervals of 30/60/90 seconds may be selected. See page 57 for information on using this function.


Information


VIN number:


The VIN (Vehicle Identification Number) is the car's unique identity number.


Number of Keys:


The number of keys registered for the car is displayed here.


Climate functions


Blower speed in AUTO mode:


The blower speed can be set to AUTO mode in models equipped with ECC. Choose between "Low", "Normal" and "High".


Timer for recirculation:


When the timer is active, the air recirculates in the car for 3-12 minutes depending on the ambient temperature. Select On/Off depending on whether the recirculation timer is to be active or not.


Reset to factory settings Use this alternative to return to the default climate system settings.


73 02 Instruments and controls


HomeLink® Universal Transceiver (option)


Introduction


HomeLink1 is a system that can be programmed to learn the codes of three different remote controlled-devices (for example, a garage door opener, remote lighting, entry gate). HomeLink's sun visor-mounted transceiver, powered by your car's electrical system, may then be used in place of your handheld remote controls. The HomeLink transceiver consists of three programmable buttons and an indicator light.


1HomeLink is a registered trademark of Johnson Controls, Intl.


© JCI, All rights reserved


NOTE


For your security, the HomeLink Universal Transceiver is designed to not function if you lock your car from the


outside.


vehicle.


Retain the original transmitter(s) for future programming procedures (for example, if you purchase a new vehicle). For your own security, erase all programmed buttons on the HomeLink Universal Transceiver when you sell your


Metallic sun protection films should not be used on any windows in a vehicle equipped with HomeLink Universal


Transceiver. This could interfere with the transceivers function.


Operating the HomeLink Universal Transceiver Once programmed, the HomeLink Universal Transceiver can be used in place of your handheld transmitters.


NOTE


The HomeLink universal transceiver will function for 30 minutes after the driver's door has been opened without switching on the vehicle's ignition.


Press the programmed HomeLink button to activate the garage door, driveway gate, security lightning, home security system etc. Your original hand-held transmitters may, of course, be used at any time.


WARNING


If you use HomeLink to open a garage door or gate, be sure no one is near the gate or door while it is in motion. Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety "stop" and


"reverse" features as required by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982). A garage door opener that cannot "detect" an object, signalling the door to "stop" and "reverse" does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death. For more information on this matter, call toll-free 1-800-355-3515. (Internet: www.HomeLink.com).


Programming the transceiver for the first time (U.S. residents) 1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.)


2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface


74 02 Instruments and controls


HomeLink® Universal Transceiver (option)


(located on your sun visor), keeping the HomeLink indicator light in view.


3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)


NOTE


Some garage door openers may require you to replace step 3 with the "cycling" procedure noted in the "Programming the transceiver for the first time (Canadian residents)" section.


4. Press and hold the trained HomeLink button and observe the indicator light.


If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink


button is pressed and released.


If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following


training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.


5. At the garage door opener receiver (motorhead unit) in the garage, locate the "learn" or "smart" button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener's manual or contact us toll-free 1-800-355-3515 (Internet: www.HomeLink.com).


6. Press and release the "learn" or "smart" button (the name and color of the button may vary by manufacturer).


NOTE


Once the button is pressed, there are 30 seconds in which to initiate the next step.


7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the "press/hold/release" sequence up to 3 times to complete the training process.


To train additional HomeLink buttons, begin with step two.


Programming the transceiver for the first time (Canadian residents) 1. For first time training, press and hold the two outer HomeLink buttons releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.)


2. Position the hand-held transmitter 1-3 inches (2.5-7.5 cm) away from the HomeLink surface (located on your) keeping the HomeLink indicator light in view.


3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. During programming, your handheld transmitter may automatically stop transmitting. Continue to press and


hold the desired HomeLink button while you press and re-press ("cycle") your handheld transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly and then rapidly after several seconds upon successful training. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)


75 02 Instruments and controls


HomeLink® Universal Transceiver (option)


4. Press and hold the trained HomeLink button and observe the indicator light.


If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink


button is pressed and released.


If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following


training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.


5. At the garage door opener receiver (motorhead unit) in the garage, locate the "learn" or "smart" button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button reference the garage door opener's manual or contact us.


6. Press and release the "learn" or "smart" button (the name and color of the button may vary by manufacturer).


NOTE


Once the button is pressed, there are 30 seconds in which to initiate the next step.


7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the "press/hold/release" sequence up to 3 times to complete the training process.


NOTE


During programming, your hand-held transmitter may automatically stop transmitting. Continue to press and hold the desired HomeLink button while you press and repress ("cycle") your hand-held transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly and then rapidly after several seconds upon successful training. If necessary, follow steps 5-7 to complete the training for a rolling code device.


To train additional HomeLink buttons, begin with step two.


Rolling Code Programming Rolling code garage door openers that are "code-protected" and manufactured after 1996 may be determined by the- following:


Reference the garage door opener owner's manual for verification. The handheld transmitter appears to program the HomeLink Universal Transceiver but does not activate the garage


door.


Press and hold the trained HomeLink button. The garage door opener has the rolling code feature if the indicator


light flashes rapidly and then turns solid after 2 seconds.


To train a garage door with the rolling code feature, follow these instructions (the aid of a second person may make the training quicker and easier):


1. Locate the training button on the garage door opener motor head unit. Exact location and color of the button may vary by garage door opener brand. If there is difficulty locating the training button, reference the garage door opener owner's manual or please visit our Web site at www.homelink.com.


2. Press the training button on the garage door opener motor head unit (which activates the "training light").


NOTE


Following step 2, there are 30 seconds in which to initiate step 3.


3. Firmly press and release the programmed HomeLink® button. Press and release the HomeLink button a second time to complete the training process. (Some garage door openers may require


76 02 Instruments and controls


HomeLink® Universal Transceiver (option)


you to do this procedure a third time to complete the training.)


The garage door opener should now recognize the HomeLink Wireless Control System. The remaining two buttons may now be trained if this has not previously been done. Refer to the Programming portion of this text. The HomeLink Wireless Control System (once programmed) or the original handheld transmitter may be used to activate the garage door. In the event that there are still difficulties in programming the HomeLink Wireless Control System, please visit our Web site, www.homelink.com.


Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps:


1. Press and hold the desired HomeLink button. Do NOT release until step 4 has been completed.


2. When the indicator light begins to flash slowly ( after 20 seconds), position the handheld transmitter 1 to 3 inches away from the HomeLink surface.


3. Press and hold the handheld transmitter button. The HomeLink indicator light will flash, first slowly and then rapidly.


4. When the indicator light begins to flash rapidly, release both buttons.


The previous device has now been erased and the new device can be activated by pushing the HomeLink button that has just been programmed. This procedure will not affect any other programmed HomeLink.


Erasing Channels Individual buttons cannot be erased. However, to erase all three programmed buttons:


1. Press and hold the two outside buttons until the indicator light begins to flash (after 20 seconds).


2. Release both buttons.


The HomeLink® Wireless Control System is now in the training (learning) mode and can be programmed at any time following steps 2 through 4 in the Programming section.


77 02 Instruments and controls


This page left intentionally blank.


Contents | Top of Page


2 0 0 8
VOLVO


C70


78 03 Climate


80
General information Air vents 81
Electronic Climate Control (ECC) 82
Air distribution 86


79 03 Climate


80 03 Climate


General information


Air conditioning - A/C


Your car is equipped with an Electronic Climate Control (ECC).


The air conditioning system can be switched off, but for optimal air quality in the passenger compartment and to prevent the windows from fogging, the air conditioning should be left on - even in cool weather.


NOTE


In warm weather, a small amount of water may accumulate under the car when it has been parked. This water is condensation from the A/C system and is normal.


Ice and snow


Always keep the air intake grille at the base of the windshield free of snow.


Fog on the inside of the windows


The defroster function should be used to remove fog or mist from the inside of the windows. Keeping the windows clean with a commercially available window washing spray will also help prevent fogging or misting.


Climate control maintenance


Special tools and equipment are required to maintain and carry out repairs on the climate system. Work of this type should only be done by a trained and qualified Volvo service technician.


Refrigerant


Volvo cares about the environment. The air conditioning system in your car contains a CFC-free refrigerant - R134a. This substance will not deplete the ozone layer. The system contains 1.2 lbs (530 g) R134a (HFC 134a), and uses PAG oil.


Passenger compartment filter


Replace the cabin air filter with a new one at the recommended intervals. Please refer to your Warranty and Service Records Information booklet, or consult a trained and qualified Volvo service technician for these intervals. The filter should be replaced more often when driving under dirty and dusty conditions. The filter cannot be cleaned and therefore should always be replaced with a new one.


NOTE


There are different types of cabin air filters. Ensure that the correct type is installed.


Display


The display above the climate control panel shows the climate settings that have been made.


Personal settings


There are two functions in the climate system that can be set to your preferences:


Blower speed to Auto mode (models with ECC only). Timer controlled recirculation of the air in the passenger compartment.


For information about how to make these settings, see the Personal settings section on page 71.


81 03 Climate


Air vents


Air vents in the dashboard


A. Open


B. Closed


C. Horizontal air flow


D. Vertical air flow


Direct the outer air vents toward the side windows to defrost.


82 03 Climate


Electronic Climate Control (ECC)


1. Auto - On/Off


2. Blower speed


3. Recirculation


4. Defroster


5. Airflow controls


6. A/C - ON/OFF


7. Heated driver's seat


8. Heated front passenger's seat


9. Rear window and door mirror defrosters


10. Temperature selector


NOTE


The sunlight sensor on the upper side of the dashboard and the passenger compartment temperature sensor, located


behind the climate system control panel, should not be obstructed.


The air conditioning system is temporarily switched off during full throttle acceleration.


ECC functions


1. Auto - On/Off


The AUTO function automatically regulates climate control to maintain the desired temperature. The automatic function controls heating, air conditioning, blower speed, recirculation, and air distribution.


If you select one or more manual functions, the remaining functions continue to be controlled automatically. All manual settings are


83 03 Climate


Electronic Climate Control (ECC)


switched off when AUTO is switched on. AUTO CLIMATE is shown in the display.


2. Blower speed


The blower speed can be increased or decreased by turning the knob. The blower speed is regulated automatically if AUTO is selected. The previously set blower speed is disconnected.


NOTE


If the knob is turned counterclockwise and the blower indication in the display goes out, the blower and the air conditioning are switched off. The display shows the blower symbol and OFF.


3. Recirculation


This function can be used to shut out exhaust fumes, smoke, etc from the passenger compartment. The air in the passenger compartment is then recirculated, i.e. no air from outside the car is taken into the car when this function is activated.


If the air in the car recirculates for too long, there is a risk of condensation forming on the insides of the windows,


especially in winter.


Timer The timer function minimizes the risk of fogging, or stale air when the recirculation function is selected. See page 72
for information on setting the recirculation timer.


NOTE


Recirculation is always disengaged if the defroster button is engaged to clear ice or condensation from the side windows.


4. Defroster


Directs airflow to the windshield and side windows and increases blower speed.


When the defroster is activated:


Air flows to the windows at high blower speed. The LED in the defroster button lights up when this function is activated. The air conditioning system is controlled


to provide maximum air dehumidification.


The air conditioning is automatically switched on (can be switched off by pressing button 5).


The air is not recirculated.


5. Airflow controls


Press one of the three buttons in the illustration to activate the selected airflow. A symbol in the display above the climate control panel and a lit LED in the selected button indicate that the manual function has been selected. With manually selected airflow both warm and cool air can be selected. See also the table on page 86.


6. Air conditioning On/Off


ON: The air conditioning system is engaged when the ON light is lit and is controlled automatically by the system to maintain the selected temperature.


OFF: The system is disengaged when the OFF lights up


When OFF is selected and the OFF LED is lit, the air conditioning system is deactivated.


84 03 Climate


Electronic Climate Control (ECC)


Other functions are still controlled automatically.


When Defroster (4) is selected, the air conditioning system is activated for maximum dehumidifying.


7 and 8. Heated front seats (option)


Maximum heating: Press the button once - both LEDs light up.


Reduced heating: Press the button a second time - one LED lights up.


Seat heating off: Press the button a third time - no LEDs are lit.


9. Rear window and door mirror defrosters


Press to defrost the rear window and door mirrors.


The rear window and door mirrors are defrosted simultaneously if the switch is pressed once. The defrost function is active if the LED in the switch is illuminated.


The function can be switched off manually by pressing the button. The defrost function switches off automatically after 12-20 minutes, depending on the outside temperature.


NOTE


This function is automatically switched off when the power retractable hard top is down. On certain markets, the defrost function may remain on longer than 20 minutes in cold weather to help keep the


rear window free from ice or condensation.


10. Temperature selector


The temperatures on the driver's and passenger's sides can be set separately using the knob (with the thermometer in it). The temperature can be set for both sides of the car when the ignition is switched on (both LEDs will be on), which means that a temperature setting will apply to both sides of the car.


To set the temperature on one side of the car:


Press the knob once. The LED for one side of the car will light up. Turn the knob to adjust the temperature. Press the knob a second time to set the temperature on the opposite side of the car. Press the knob a third time to set the temperature on both sides of the car at the same time.


NOTE


Selecting a temperature that is higher or lower than necessary will not heat or cool the passenger compartment faster.


85 03 Climate


Electronic Climate Control (ECC)


ECC sensors


The sunlight sensor is on the upper side of the dashboard


The passenger compartment temperature sensor is located behind the climate system control panel. The ambient temperature sensor is in the driver's side door mirror. The humidity sensor is in the rearview mirror.


These sensors should never be obstructed.


NOTE


The sunlight sensor monitors the side of the vehicle from which the sun shines into the passenger compartment. This means that the temperature may differ slightly between the left and right air vents, even if the climate system temperature is set to be the same for both sides of the passenger compartment.


86 03 Climate


Air distribution


87 03 Climate


This page left intentionally blank.


Contents | Top of Page


2 0 0 8
VOLVO


C70


88 04 Interior


Front seats 90
Power retractable hard top 94
100
Interior lighting Storage compartments 102
107
Trunk


89 04 Interior


90 04 Interior


Front seats


Manual seat adjustment


The driver's and passenger's seats can be adjusted in a number of ways to provide a comfortable driving and sitting position.


1. Forward-rearward: Pull the lever up and slide the seat to the position of your choice.


2. Use this control to raise or lower the front edge of the seat cushion.


3. Use this control to raise or lower the rear edge of the seat cushion.


4. Turn this knob (option on some passenger's seats) to adjust the firmness of the lumbar support1.


5. Turn this knob to adjust the backrest tilt.


6. Control panel for power seats.


WARNING


Do not adjust the seat while driving. Adjust the driver's seat and seat belt (see page 14) before driving. The seat should be adjusted so that the brake


pedal can be depressed fully.


Position the seat as far rearward as comfort and control allow.


1Also applies to the optional power seat.


91 04 Interior


Front seats


Accessing the rear seat


Seat access buttons (power seat shown)


Manual seat Moving the seat forward:


1. Remove the seat belt from its guide (see page 15).


2. Pull up control 1 (see the illustration), hold it up, and fold the backrest forward until it locks in position.


3. Slide the seat forward.


Moving the seat rearward:


1. With the backrest folded forward in the locked position, slide the seat rearward to its original position.


2. Pull up control 1, hold it up, and fold up the backrest to the upright position.


3. Return the seat belt to its guide.


Power seats Easy entry is only intended to be used when the front seat in unoccupied.


Moving the seat forward:


1. Remove the seat belt from its guide (see page 15).


2. Pull up control 1, hold it up, and fold the backrest forward until it locks in position.


3. Press and hold button 2 while the seat moves forward.


Moving the seat rearward:


1. With the backrest folded forward in the locked position, press and hold down button 2 until the seat has returned to its original position.


2. Pull up control 1, hold it up, and fold up the backrest to the upright position.


3. Return the seat belt to its guide.


WARNING


After the seat has been returned to its original position, be sure that the backrest is securely locked in the upright position.


92 04 Interior


Front seats


Power seats (option)


The power driver's seat can be adjusted:


If the ignition key is in position I or II. During a 10 minute period after the doors have been unlocked if the door remains open. If the door is closed and the ignition key is not yet in the ignition, or if the key is in position 0, the seat can be


adjusted or during a period of 40 seconds. The power passenger's seat can only be adjusted if the ignition key is in position I or II, or if the engine is running.


Adjusting the seat Seat adjustment controls 1, 2, 3, and 4 on the side of the seat can be used to move the seat to the position of your choice.


1. Move this section of the control up or down to raise/lower the front section of the seat cushion.


2. Move the control forward/rearward to move the seat forward or rearward.


3. Move this section of the control up or down to raise/lower the rear section of the seat cushion.


4. Backrest tilt.


NOTE


The power seats have an overload protector that activates if a seat is blocked by any object. If this occurs, switch off the ignition (key in position 0) and wait for approximately 20 seconds before operating the seat again.


Emergency stop If the seat inadvertently begins to move, press any of the buttons to stop the seat.


Programming the seat memory, driver's seat only (option)


Three different seating positions (and the position of the door mirrors) can be stored in the seat's memory. The memory buttons are located on the outboard side of the driver's seat (see the illustration). The following example explains how memory button 1 can be programmed. Buttons 2 and 3 can be programmed in the same way.


To program (store) a seat position in memory button 1:


1. Adjust the seat (and door mirrors) to the desired position (see the instructions under "Adjusting the seat").


93 04 Interior


Front seats


2. Press and hold down the "M" (Memory) button.


3. With the "M" button depressed, press memory button 1 to store the seat's current position.


To move the seat to the position that it was in when memory button 1 was programmed, press and hold down button 1
until the seat stops moving.


As a safety precaution, the seat will stop automatically if the button is released before the seat has reached the preset position.


Central locking system remote control and driver's seat memory The remote control transmitter can also be equipped with an optional function that controls the electrically operated driver's seat and door mirrors in the following way:


1. Adjust the seat and door mirrors to the desired position.


2. When you leave the car, lock it using the remote control.


3. The next time the driver's door is unlocked with the same remote control and that door is opened within 2 minutes, the driver's seat and door mirrors will automatically move to the position that they were in when the doors were most recently locked with the same remote control.


NOTE


The memory function in the remote control operates independently of the memory function in the seat.


WARNING


Because the driver's seat can be adjusted with the ignition off, children should never be left unattended in the car. Movement of the seat can be STOPPED at any time by pressing any button on the power seat control panel. Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. In


addition, position the seat as far rearward as comfort and control allow.


The seat rails on the floor must not be obstructed in any way when the seat is in motion.


94 04 Interior


Power retractable hard top


Before raising and lowering the power retractable hard top


Please observe the following information before operating the power retractable hard top:


There should be no objects on the power retractable hard top's cover. Remove all snow, ice or loose objects from the power retractable hard top and trunk lid. The top should be dry before it is lowered.


CAUTION


If the power retractable hard top is lowered while it is wet, water may drip into the passenger compartment or trunk


There should be at least 6.5 feet (2 meters) of free space from the ground (distance A in the illustration). There should be at least 8 inches (20 cm) of free space behind the vehicle (distance B in the illustration in the center


column).


The ambient temperature should be above 14°F (-10°C). The trunk divider (see page 95) must be closed. The trunk must be closed. The vehicle must be at a standstill and the brake pedal must be pressed.


Volvo also recommends the following:


The vehicle should be parked outdoors, on level ground. Raising or lowering the power retractable hard top should preferably be done in one, continuous operation. If the vehicle is parked outdoors, the engine should be idling to help avoid battery drain.


CAUTION


If the instructions on these pages are not followed, damage to the power retractable hard top's mechanism may occur.


WARNING


The power retractable hard top must not be obstructed in any way when it is being operated. Always have an unobstructed view of the power retractable hard top when it is in motion. See also the decal on the trunk divider.


Anyone near the vehicle should be well clear of the power retractable hard top's moving parts before it is operated. Children must never be allowed to play with the power retractable hard top control buttons. Do not leave the power retractable hard top motionless longer than necessary while it is being operated Do not leave the key in the ignition if there are children in the vehicle.


95 04 Interior


Power retractable hard top


Trunk divider


The purpose of the trunk divider is to indicate the amount of cargo that can be stowed in the trunk without affecting movement of the power retractable hard top.


To open, grasp the handle and lift.


To close, pull the trunk divider rearward.


Be sure to close the trunk divider completely so that it locks in place on both the right and left sides.


NOTE


If the trunk divider is not completely closed, it will not be possible to operate the power retractable hard top.


Power retractable hard top cover


When lowered, the power retractable hard top is concealed by a cover, see the illustration above.


CAUTION


Do not sit or place heavy objects on the power retractable hard top cover.


96 04 Interior


Power retractable hard top


Raising or lowering the power retractable hard top


1. Turn the ignition key to position II, or start the engine if the vehicle is parked outdoors.


2. Press the brake pedal.


3. Press and hold down the left button (1) to raise the power retractable hard top or the right button (2) to lower it. Hold down the respective button until the top is completely raised or lowered. Release the button when an audible signal sounds. The message ROOF OPEN or ROOF CLOSED will be displayed.


CAUTION


Please heed any messages that may appear in the information display while the top is in operation. Any windows that are closed will be opened approximately 4 inches (10 cm) while the power retractable hard top


is in operation. The windows will be automatically re-closed when the top is completely raised or lowered.


WARNING


See the section "Before raising or lowering the power retractable hard top" on page 94 before operating the power


retractable hard top.


Never pull the release wire for the power retractable hard top's hydraulic system that is located under the rear seat


cushion. This wire is only intended for use by qualified service personnel. Pulling this wire could lead to:


High risk of being injured by the power retractable hard top mechanism. Unexpected movement of the hard top, or the hard top or the trunk could inadvertently open. The retractable hard top can be damaged.


Power retractable hard top-related text messages


PRESS BRAKE TO OPERATE ROOF


Press the brake pedal to operate the retractable hard top.


CLOSE TRUNK FOR ROOF OPERATION


CLOSE TRUNK SEP. FOR ROOF OPERAT


The trunk divider (see page 95 for more


The trunk is open and must be closed before operating the power retractable hard top.


97 04 Interior


Power retractable hard top


information) must be closed before operating the power retractable hard top.


LOW BATTERY FOR ROOF OPERATION


The battery's charge is too low to operate the power retractable hard top. In this case, the top can only be raised. Start the engine, or if necessary, have the battery charged before operating the top.


ROOF NOT LOCKED


The power retractable hard top is not fully up or down. Press and hold down the respective button again to complete the operation.


TEMP LIMITS ROOF OPERATION


The power retractable hard top mechanism has overheated, or the ambient temperature is below 14¡ F (-10¡ C). If the mechanism has overheated, wait for approximately 5 minutes (the message in the information display will disappear) and try to lower or raise the top again.


If a fault in the power retractable hard top mechanism occurs, the following messages will be displayed:


ROOF FAILURE SERVICE REQUIRED


The power retractable hard top cannot be operated. Contact an authorized Volvo retailer or service technician. If the top is down in this situation, a cover for the vehicle is provided in the trunk. See page 98 for more information.


ROOF FAILURE SEE MANUAL


The power retractable hard top must be operated according to the following instructions.


Emergency operation If the message ROOF FAILURE SEE MANUAL is displayed, the power retractable hard top cannot be operated in the normal way.


NOTE


If a fault has occurred and the power retractable hard top has been raised, it cannot be lowered again until the fault has been corrected.


CAUTION


Carefully read the information under "Before raising or lowering the power retractable hard top" on page 94 before operating the power retractable hard top. Damage may be unavoidable if the power retractable hard top must be operated under such conditions.


1. Press button 1 or 2 (see the illustration on page 96) until ROOF FAILURE SEE MANUAL is displayed.


2. Release the button.


3. Press the button again and hold it down. After approximately 5 seconds, the power retractable hard top will begin to move. Keep the button depressed until the top is fully raised.


NOTE


Movement of the top may stop briefly. However, the button should be held down throughout the entire operation. An audible signal will sound during the entire operation.


WARNING


Never pull the release wire for the power retractable hard top's hydraulic system that is located under the rear seat


cushion. This wire is only intended for use by qualified service personnel. Pulling this wire could lead to:


High risk of being injured by the power retractable hard top's opening/closing mechanism. Unexpected movement of the hard top/the hard top or the trunk could inadvertently open. The retractable hard top can be damaged.


98 04 Interior


Power retractable hard top


Temporary cover


The cover should only be used if the power retractable hard top is down and cannot be raised. It should be placed over the car so that the shock-cord attaching points are on the underside.


To install the cover 1. Raise all windows.


2. Take out the cover (stowed in the compartment in the rear side of the ski hatch in the center of the rear seat backrest), remove it from the bag and unfold it.


3. Slide the openings in the cover (3) over the respective door mirrors and attach the front shock-cord hooks (2) on the edges of the front wheel housings.


4. Slide the cover under the windshield wipers so that there is one fold under each wiper blade (1).


5. Guide the antenna through hole 5.


6. Attach the rear side hooks (4) on the edges of the rear wheel housings.


7. Attach the rear hooks (6) under the rear bumper.


99 04 Interior


Power retractable hard top


Wind blocker


The wind blocker is intended for use while driving with the power retractable hard top down to help reduce swirling breezes in the passenger compartment.


Installing the wind blocker 1. Unfold the wind blocker to its full width.


2. Unfold the supports on both rear sides.


3. Slide the winder blocker's rear supports under the rear head restraints so that they rest on the upper edge of the


backrest.


4. Press the side lock tabs into the holes in the side panels until they click into place.


5. Raise the wind blocker.


The zipper in the wind blocker can be opened to place or access objects in the rear seat.


CAUTION


Slide in the supports carefully to avoid damaging the upholstery.


WARNING


Make sure the wind blocker is securely attached. An improperly secured wind blocker may cause injury to


occupants of the vehicle or to other motorists.


No one should be allowed to sit in the rear seat when the wind blocker is in place.


When not in use, the wind blocker should be stored in its bag, in the trunk, against the rear seat backrest.


100 04 Interior


Interior lighting


Interior lighting


1. Driver's side reading light


2. Courtesy lighting


3. Passenger's side reading light


The front seat reading lights can be switched on and off by pressing buttons 1 or 3.


The courtesy lighting (2) can be set to three positions: Off - Press the right side of the button. Neutral position - the interior courtesy lighting comes on when a door is opened, and is switched off when the door


is closed.


ON - Press the left side of the button.


Rear seat reading lights


The rear reading lights can be switched on or off by pressing the respective buttons.


Courtesy lighting - automatic function


The interior lighting has a built-in automatic function that switches on the courtesy lighting for 30 seconds when:


the car is unlocked from the outside using the key or remote control the engine is switched off and the ignition key is turned to the 0 position.


The courtesy lighting lights up or remains on for 5 minutes when:


one of the doors is opened and left open. the courtesy lighting has not been switched off (the right side of button 2 depressed).


The automatic lighting goes out when:


the engine is started the car is locked from the outside using the key or remote control.


If the courtesy lighting is not switched off manually, it will be turned off automatically 5 minutes after the engine has been switched off.


101 04 Interior


Interior lighting


Vanity mirror


Raise the cover to switch on the light.


102 04 Interior


Storage compartments


103 04 Interior


Storage compartments


1. Lockable storage compartment in door


2. Jacket hanger (intended for light garments only)


3. Storage pocket on front side of front seat cushion


4. Glove compartment


5. Cup holders


6. Storage compartment in center console (for e.g. CDs)


7. Cup holders


8. Storage compartments in rear side panels


9. Storage compartment on rear side of front seat backrests.


WARNING


Anchor any heavy objects to prevent them from moving during sudden stops. Packages on the rear parcel shelf can obscure vision and may become dangerous projectiles in the event of a


sudden stop or an accident.


Glove compartment


The owners manual and maps can be stored here. There are also holders for coins, pens and fuel cards. The glove compartment can only be locked and unlocked using the detachable key blade from the central locking system's remote control. See page 115 for information on removing the key blade from the remote control, and page 124 for information on locking the glove compartment


Compartment in door panel


Open the compartment by lifting the front lower section of the lid.


Close by pressing the upper edge of the lid.


Locking function The door panel compartments can be locked by pressing the Lock button on the central locking system's remote control.


104 04 Interior


Storage compartments


Rear seat storage compartment


To open, press on the top center of the panel. Both the forward and rearward catches should release and the panel should spring open. If one side does not open, press again directly over that catch.


CAUTION


Never pull the panel; the catches may be damaged.


Press to close and latch the panel.


Jacket hanger


The jacket hanger is located on the inboard side of the front passenger's seat head restraint. It is only intended for hanging light garments.


105 04 Interior


Storage compartments


Storage under the front, center armrest


There are two storage compartments under the front, center armrest.


Press the smaller button on the front edge of the armrest and lift the armrest cover to access a shallow storage


compartment.


Press the larger button and lift the entire armrest to access a deeper compartment.


The deep storage compartment has room for 10 CD jewel cases. These cases must be inserted with their spines upward in order to allow space for 10 cases in the storage compartment.


Cup holders in the center console


Two cup holders are located under the sliding cover in the center console.


The cup holders can be lifted out if necessary. To do so, grasp the indentation on the rear edge of the cup holder and lift.


To put the cup holder back in place:


1. Slide the two locating tabs in the front side of the cup holder into the two corresponding recesses in the center console storage space.


2. Press down the rear edge of the cup holder.


To close the sliding cover, grasp the underside of the front edge and pull.


106 04 Interior


Storage compartments


Storage compartment behind the parking brake


If the buttons for optional equipment are not installed, the recess behind the parking brake can be used as a storage compartment.


107 04 Interior


Storage compartments


Loading the trunk


Loading the trunk with the power retractable hard top down When the power retractable hard top is down, it is folded in the trunk. Using the button shown in the illustration above, the folded power retractable hard top can be moved up or down slightly to facilitate loading or unloading small objects.


NOTE


This movement is part of the normal power retractable hard top operation, which means that messages pertaining to the power retractable hard top's operation (see page 96) also apply to the this function.


WARNING


Anyone near the vehicle should be well clear of the power retractable hard top's moving parts before it is operated.


CAUTION


Any objects that impede the movement of the power retractable hard top may damage the top or its mechanism. When the power retractable hard top has been raised for loading the trunk, or if its movement has been interrupted by pressing the button twice, the trunk should not be closed. Doing so can damage the system or cause paint damage.


To raise the level of the folded power retractable hard top:


1. Open the trunk.


2. Press the button on the right side of the trunk opening.


NOTE


There may be a delay of several seconds before the folded power retractable hard top begins to move. Movement of the top can be stopped by pressing the button again.


3. The folded power retractable hard top will raise slightly. If an audible signal sounds during this operation, check the


information display in the center instrument panel for messages.


4. Lift the trunk divider (see page 95) to provide an opening into the trunk.


5. When the objects to be loaded have been placed in the trunk, press down the trunk divider.


6. Press the button to move the power retractable hard top downward. Movement of the top can be stopped by pressing the button again.


7. Close the trunk.


NOTE


The trunk cannot be closed while the folded power retractable hard top is in the upper position.


108 04 Interior


Storage compartments


Raising and lowering the folded top in the event of a fault


If the message ROOF FAILURE SEE MANUAL is displayed, the folded power retractable hard top can only be lowered in the trunk.


CAUTION


Damage may be unavoidable if the power retractable hard top must be operated when this message is displayed.


Press the button again and hold it down. After approximately 2 seconds, the power retractable hard top will begin to


move. Keep the button depressed until the folded top is lowered.


NOTE


An audible signal will sound during this entire operation.


Load anchoring eyelets


The eyelets in the trunk can be used to fasten accessory load and lashing straps, load nets, and other load anchors.


12-volt socket (option)


Fold down the lid to use the socket.


Using the 12-volt socket while the engine is not running drains the vehicle's battery. If the ignition is switched off and a device drawing more that 0.1A is connected to a socket, a battery alert will be


shown in the driver information display.


The cover should be kept on when the auxiliary socket is not in use.


109 04 Interior


Storage compartments


Carrying long loads (ski hatch)


The center section of the rear seat backrest can be opened to create space for carrying long, light objects (max. length 6.5 ft/2 meters, max. weight 55 lbs/25 kg). To do so, the center section (cushion) of the rear seat backrest must be removed, the tire repair kit (if the vehicle is so equipped) must be removed and stowed in the trunk, and the plastic hatch in the trunk must be opened.


Removing the center backrest cushion Pull the strap at the upper edge of the cushion, pull it forward, and lift it out.


Opening the plastic hatch From the trunk, press the catches in the two holes in the hatch (A in the illustration) toward each other to release the hatch, and fold it down.


NOTE


If the vehicle is equipped with the optional ski bag, the bag's zipper must be opened from the passenger's compartment in order to insert objects through the ski hatch.


Replacing the backrest cushion Begin by guiding the lower section of the cushion into place. Then press the upper section of the cushion into place.


NOTE


This cushion is locked in place when the vehicle is locked with the remote control. See page 117.


Securing long objects Long objects should be secured with one of the rear seat belts.


Wrap the belt once around the object and lock the belt in the retractor as usual.


If the vehicle is equipped with the optional ski bag, pass the seat belt through the bag's handle before fastening the seat belt.


Contents | Top of Page


2 0 0 8
VOLVO


C70


110 05 Locks and alarm


112
Remote control and key blade Valet locking 117
Keyless drive (option as available) 119
Locking and unlocking 123
Glove compartment and trunk 124
Opening the trunk from the inside 125
Alarm 126


111 05 Locks and alarm


112 05 Locks and alarm


Remote control and key blade


Remote controls


Two remote controls that also function as ignition keys are provided with your car. The remote controls contain detachable metal key blades for manually locking or unlocking the driver's door and the glove compartment.


USA - FCC ID: LTQVO315TX This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Canada - IC: 3659AVO315TX Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


Loss of a remote control


If either of the remote controls is lost, the other must be taken with the car to a Volvo retailer. As an anti-theft measure, the code of the lost remote control must be erased from the system.


Each key blade has a unique code, which is used if new key blades are required. A maximum of six remote controls/key blades can be programmed and used for one car.


Immobilizer (start inhibitor)


Each of the keys supplied with your car contains a coded transponder. The code in the key is transmitted to an antenna in the ignition switch where it is compared to the code stored in the start inhibitor module. The car will start only with a properly coded key. If you misplace a key, take the other keys to an authorized Volvo retailer for reprogramming as an antitheft measure.


USA - FCC ID: LTQWFS 125VO This device complies with part 15 of the FCC rules. Operation is subject to the following condition: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Canada - IC: 3659A-WFS125VO Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


CAUTION


Never use force on the narrow section of the remote control - this is where the transponder is located. The car cannot be started if the transponder is damaged.


113 05 Locks and alarm


Remote control and key blade


Remote control functions


1. Lock - Press the Lock button on the remote once to lock both doors, the trunk, the cabin storage compartments (compartment in the doors, the rear side panels, and the ski hatch in the center of the rear seat backrest). The turn signals will flash twice to confirm locking.


NOTE


The remote control will not lock or unlock the glove compartment.


Double locking If the car is locked with the remote control while the power retractable hard top is down, the double locking feature activates after approximately 30 seconds. This means that the doors cannot be unlocked or opened from inside the car.


NOTE


The double locking function can be temporarily disabled. See page 127 for instructions.


2. Unlock - Press the Unlock button on the remote once to unlock the driver's door. The turn signals will flash twice to confirm unlocking. After a short pause, press the Unlock button a second time within 10 seconds to unlock the other doors and the trunk. A long press (for several seconds) opens the side windows.


NOTE


The turn signals flash to confirm that the vehicle has been correctly locked/unlocked with the remote control. When locking the vehicle, the turn signals will flash a confirmation only if all the doors are securely closed and locked. Flashing confirmation for locking and unlocking may be customized in the vehicle's Personal settings menu. See page 71 for more information.


The two-step unlocking function can be changed so that one press of the Unlock button unlocks all of the doors


and the trunk. See Personal settings on page 71 for more information.


Automatic relocking: If the doors are unlocked, the locks will automatically reengage (re-lock) and the alarm will


rearm after 2 minutes unless a door or the trunk has been opened.


Automatic locking: When the car starts to move, the doors and trunk can be locked automatically. This feature


can be turned on or off, see Personal settings on page 72 for more information.


Airbag deployment will automatically attempt to unlock the doors.


3. Approach lighting - As you approach the car: Press the button on the remote control to illuminate the area around the car in dark conditions.


114 05 Locks and alarm


Remote control and key blade


Pressing the button once lights up the interior lighting, parking lights, and license plate lighting. These lights will switch off automatically after 30, 60 or 90 seconds. See the Personal settings on page 71 for information about adjusting the time setting.


4. Unlock trunk- Press the button once to disarm the alarm system and unlock only the trunk. After closing, the trunk will not automatically relock. Press Lock to relock it and rearm the alarm.


NOTE


This function will unlock, but not pop open, the trunk.


5. Panic alarm: - This button can be used to attract attention during emergency situations. To activate the panic alarm, press and hold the red button for at least 3 seconds or press it twice within 3 seconds. The


turn signals and horn will be activated. The panic alarm will stop automatically after 30 seconds. To deactivate, wait approximately 5 seconds and press the red button again.


NOTE


This button will NOT unlock the car.


Weak battery in the remote control


When the battery begins to lose its charge, the Information symbol in the instrument panel (see page 49) lights up and REMOTE BATTERY LOW VOLTAGE is shown in the information display.


Replacing the battery in the remote control


If the range of the transmitter is noticeably reduced, this indicates that the battery (type CR 2450, 3V) is weak and should be replaced. To replace the battery:


115 05 Locks and alarm


Remote control and key blade


1. Place the remote control with the keypad downward. Pry open the cover with a small slotted screwdriver.


2. Remove the cover.


3. Note how the + and - sides of the battery are positioned on the inside of the cover (see the underside of the cover).


CAUTION


When replacing the battery, avoid touching the electrical circuitry in the other half of the remote control.


4. Pry out (2) and replace the battery. Avoid touching the battery and its contact surfaces with your fingers.


5. Press the cover back into place and tighten the screw.


6. Reinsert the key blade in the remote control.


The old battery should be disposed of properly at a recycling center or at your Volvo retailer.


Key blade


The key blade can be removed from the remote control. When removed, it can be used as follows:


To lock/unlock the driver's door To lock/unlock the glove compartment (see page 124) To mechanically open the trunk (see page 124) For valet locking (see page 117)


Removing the key blade Slide the spring loaded catch (1) to the side and pull the key blade (2) out of the remote control.


Reinserting the key blade in the remote control 1. Hold the remote control with the pointed end down.


2. Carefully slide the key blade into its groove.


3. Gently press the key blade in the groove until it clicks into place.


Unlocking the doors with the detached key blade 1. Insert the key blade as far as possible in the driver's door lock. Turn the key blade clockwise approximately one- quarter turn to unlock the driver's door only.


NOTE


After unlocking the driver's door with the key blade, opening the door will trigger the alarm.


To disable the alarm: 1. Press the Unlock button on the remote control, or insert the key in the ignition switch.


116 05 Locks and alarm


Remote control and key blade


Locking the doors with the detached key blade 1. Lock the passenger's door by pressing the lock button on the door.


2. Turn the key blade one-quarter turn counter-clockwise to lock the driver's door.


NOTE


This does not arm the alarm or lock the trunk.


117 05 Locks and alarm


Valet locking


Introduction


By utilizing the remote control with the key blade removed, the valet locking feature enables you to block access to the trunk and glove compartment for e.g., valet parking or when the car is brought to the retailer for service.


Locking points A. Doors B. Steering wheel lock C. Glove compartment D. Compartments in door panels E. Ski hatch F. Trunk


With the valet locking function activated:


The vehicle's doors can be locked or unlocked The engine can be started Locking points C, D, E, and F cannot be unlocked with the remote control.


118 05 Locks and alarm


Valet locking


Activating the valet locking function Begin by removing the key blade from the remote control (see page 115).


NOTE


The first stages of opening the power retractable hard top offer temporary access to the contents of the trunk. Therefore, before activating valet locking, the power retractable hard top must be up and the trunk divider must be open (up), see page 95. This makes it impossible to operate the power retractable hard top.


Insert the key in the glove compartment lock.


Turn the key blade 180° clockwise to lock the glove compartment and to lock points C, D, E, and F and disconnect


these points from the central locking system (a message appears in the information display).


Remove the key blade from the glove compartment lock.


Give the parking attendant or service personnel only the remote control (with the key blade removed).


Deactivating the valet locking function Turn the key blade 180° counterclockwise in the glove compartment lock to deactivate valet locking (the trunk can then be unlocked using the remote control).


See page 124 for information on locking the glove compartment normally.


119 05 Locks and alarm


Keyless drive (option as available)


Keyless locking and unlocking


This system makes it possible to unlock and lock the vehicle without having to use the remote control. It is only necessary to have a keyless drive remote control in your possession to operate the central locking system.


NOTE


The buttons on the keyless drive remote control can also be used to lock and unlock the vehicle. See page 113 for more information.


Both of the remote controls provided with the vehicle have the keyless function, and additional remotes can be ordered. The system can accommodate up to six keyless drive remote controls.


NOTE


The number of doors that are unlocked at the same time can be set in the Personal settings menu. See page 71 for additional information.


1. A keyless drive remote control must be on the same side of the vehicle as the door to be opened, and be within 5
feet (1.5 meters) of the lock or the trunk opening control (see the shaded areas in the illustration).


2. Pull a door handle to unlock and open the door or press the trunk opening control on the trunk lid.


Locking the vehicle


The doors and the trunk can be locked by pressing the lock button in any of the outside door handles.


NOTE


If one or more doors and/or the trunk is not fully closed when the lock button is pressed, the door(s) or trunk will


not be locked.


On keyless drive vehicles with an automatic transmission, the gear selector must be in the Park (P) position and


the ignition must be switched off before the doors/trunk can be locked.


120 05 Locks and alarm


Keyless drive (option as available)


Locking or unlocking the vehicle with the key blade


The driver's door on vehicles equipped with keyless drive can be locked or unlocked with the remote control's detachable key blade if necessary. See page 115 for information on removing the key blade from the remote control. To access the keyhole in the driver's door:


1. Pry off the keyhole cover by inserting the key blade or a small screwdriver in the hole on the underside of the cover (indicated by the arrow in the inset illustration).


2. Insert the key blade as far as possible in the driver's door lock. Turn the key blade clockwise approximately one quarter turn to unlock the driver's door only. This will trigger the alarm.


Disabling the alarm: Press the Unlock button on the keyless drive remote control. If the batteries in the remote are weak, remove the keyless drive start control from the ignition switch by pressing the catch (see the illustration on page 142) and pulling the control out of the ignition switch. Insert the ignition key section of a keyless drive remote control in the ignition switch.


Keyless drive remote control and driver's seat memory This function is only available on vehicles equipped with the optional power driver's seat.


When you leave the car with a keyless drive remote control in your possession and lock any door, the position of


the driver's seat will be stored in the seat's memory.


The next time a door is opened by a person with the same remote control in his/her possession, the driver's seat will


automatically move to the position that it was in when the door was most recently locked.


NOTE


If several people carrying keyless drive remote controls approach the vehicle at the same time, the driver's seat will assume the position it was in for the person who opens a door first.


121 05 Locks and alarm


Keyless drive (option as available)


Keyless drive information messages If anyone leaves the vehicle with the only keyless drive remote control in his or her possession while the ignition is switched on, a message will be shown in the information display and an audible signal will sound.


NOTE


This message will only be displayed if the start control is in position I or II.


The message will be erased from the display and the audible signal will stop when the remote control has been returned to the vehicle and one of the following has occurred:


A door has been opened and closed The start control has been turned to position 0
The READ button (see page 53 for the location of this button) has been pressed.


CAUTION


Keyless drive remote controls should never be left in the vehicle. In the event of a break-in, a remote found in the


vehicle could make it possible to start the engine.


Electromagnetic fields or metal obstructions can interfere with the keyless drive system. Avoid placing the remote


control near cellular phones, metallic objects or e.g., in a metal briefcase.


Canada - IC:267T- 5WK48952, 267T- 5WK48964, 267T-5WK48891
NOTE This device complies with RSS -210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.


USA - FCC ID:KR55WK48952, KR55WK48964
NOTE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Siemens VDO 5WK48891
Tested To Comply With FCC Standards For Automobile Use


122 05 Locks and alarm


Keyless drive (option as available)


Location of the keyless drive antennas


The keyless drive system has a number of antennas located at various points in the vehicle.


1. On the inside center of the rear bumper


2. Under the floor of the trunk, near the rear seat


3. Left door handle


4. Under the rear section of the center console


5. Right door handle


6. Under the front section of the center console.


WARNING


People with implanted pacemakers should not allow the pacemaker to come closer than 9 inches (22 cm) to any of the keyless drive system's antennas. This is to help prevent interference between the pacemaker and the keyless drive system.


123 05 Locks and alarm


Locking and unlocking


Locking/unlocking the car from the inside


The switches near the door opening handles on the driver's and passenger's doors can be used to lock or unlock both doors and the trunk, and to set the alarm.


Unlocking


Press in the upper section in the lock button.


Locking


Press in the lower section of the lock button.


Lock indicator lights An indicator light in each door will illuminate for approximately 5 minutes after the car has been locked using the remote control.


If doors are locked: The indicator lights will flash once. If doors are Unlocked: The indicator lights will flash twice During driving with doors locked: The indicator lights will be Off.


NOTE


The doors cannot be opened by pulling up the lock button. If both doors are closed when a lock button is pressed, the alarm will not be armed. Each door can also be locked manually using the lock button on that particular door. This applies only if the car


has not been locked from the outside.


The doors can also be unlocked (and the door opened) by pulling the handle in the door twice.


124 05 Locks and alarm


Glove compartment and trunk


Locking the glove compartment


The glove compartment can only be locked and unlocked using the detachable key blade on the remote control. See page 115 for information on removing the key blade from the remote control.


Insert the key blade in the glove compartment lock.


Turn the key blade 90 degrees clockwise.


The key slot will be in the horizontal position. Remove the key blade.


Unlock the glove compartment in the reverse order.


Mechanically opening the trunk


1. Fold down the driver's seat backrest to access the keyhole near the floor of the rear seat.


2. Insert the key blade in the keyhole and turn it 110 degrees clockwise.


CAUTION


This function should never be used when the power retractable hard top is in motion. This could cause damage to the trunk lid/hard top.


125 05 Locks and alarm


Opening the trunk from the inside


Opening the trunk from the inside


U.S. models only The car is equipped with a florescent handle on the inside of the trunk lid, which can be used in an emergency situation to open the trunk from the inside.


Pull the handle down to release the trunk lid. After use, the handle must be pushed back into its original position before the trunk can be closed.


126 05 Locks and alarm


Alarm


The alarm system


The alarm is automatically armed whenever the car is locked with the remote control, or if a front lock button is depressed.


When armed, the alarm continuously monitors a number of points on the car. The following conditions will trigger the alarm:


The hood is forced open. The trunk is forced open. A door is forced open. The ignition switch is tampered with. An attempt is made to start the car with a non-approved key (a key not coded to the car's ignition). If there is movement in the passenger compartment (if the car is equipped with the optional movement sensor). The car is lifted or towed (if the car is equipped with the optional inclination sensor) The battery is disconnected (while the alarm is armed). The siren is disconnected when the alarm is disarmed.


NOTE


The alarm system functions in the same way, regardless of whether the power retractable hard top is raised or lowered.


The alarm indicator light


The status of the alarm system is indicated by the indicator light on at the top of the dashboard (see illustration):


Indicator light off - the alarm is not armed The indicator light flashes every two seconds - the alarm is armed The indicator light flashes rapidly before the ignition is switched on - the alarm has been triggered. The message


"ALARM TRIGGERED, CHECK CAR" will also be displayed.


127 05 Locks and alarm


Alarm


Fault in the alarm system


If a fault has been detected in the alarm system, a message will be shown in the information display. Contact a


trained and qualified Volvo service technician to have the alarm system inspected and repaired if necessary.


Arming the alarm


Press the LOCK button on the remote control, or press the central lock button on one of the front doors with the door open. One long flash of the turn signals will confirm that the alarm is armed.


Disarming the alarm


Press the UNLOCK button on the remote control or insert the key in the ignition to disarm the alarm. Two short flashes from the car's direction indicators confirm that the alarm has been deactivated and that all doors are unlocked.


Turning off (stopping) the alarm


If the alarm is sounding, it can be stopped by pressing the UNLOCK button on the remote control or by inserting the key in the ignition switch. The driver's door must first be unlocked with the key blade.


Audible/visual alarm signal


An audible alarm signal is given by a battery powered siren. The alarm cycle lasts for 30 seconds.


NOTE


The visual alarm signal is given by flashing all turn signals and turning on the interior lighting for approximately 5
minutes.


Temporarily turning off the double locking function and alarm sensor(s)


In certain situations it may be desirable to turn off the accessory inclination and movement alarm sensors, and/or the double locking function if, for example, you drive your vehicle onto a ferry where the rocking of the boat could trigger the alarm or if a pet is left in the vehicle with the doors locked.


1. From position II or higher, turn the ignition key to 0 and remove it from the ignition switch.


2. Press the button (1). The LED in the button will remain on for one minute


128 05 Locks and alarm


Alarm


after the key has been removed from the ignition switch or until the car is locked.


NOTE


This will also disable the double locking function if the car is locked while the top is down. Double locking only functions with the top down.


CAUTION


The accessory sensors and double locking function (if the top is down) are automatically reconnected to the alarm


system the next time the vehicle is unlocked and then locked again.


This function will not disarm the vehicle's standard alarm.


U.S.A. FCC ID: MAYDA 5823(3) This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Canada IC: 4405A-DA 5823(3)


Movement sensor DA5823 by Dynex Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


129 05 Locks and alarm


This page left intentionally blank.


Contents | Top of Page


2 0 0 8
VOLVO


C70


130 06 Starting and driving


132
General information 136
Fuel requirements 139
Ignition switch/Steering wheel lock 140
Starting the vehicle 142
Starting the car with keyless drive (option) 143
Manual transmission 144
Automatic transmission 146
Shiftlock override 147
Brake system 149
Stability system 151
Towing 154
Jump starting 155
Towing a trailer 157
Detachable trailer hitch Transporting loads 158
Blind Spot Information System (BLIS)-option 159
163
Park assist (Option/accessory)


131 06 Starting and driving


132 06 Starting and driving


General information


Economical driving conserves natural resources


Better driving economy may be obtained by thinking ahead, avoiding rapid starts and stops and adjusting the speed of your vehicle to immediate traffic conditions.


Observe the following rules:


Bring the engine to normal operating temperature as soon as possible by driving with a light foot on the accelerator


pedal for the first few minutes of operation. A cold engine uses more fuel and is subject to increased wear.


Whenever possible, avoid using the vehicle for driving short distances. This does not allow the engine to reach


normal operating temperature.


Drive carefully and avoid rapid acceleration and hard braking. Use the transmission's Drive (D) position as often as possible and avoid using kickdown. Do not exceed posted speed limits. Avoid carrying unnecessary items (extra load) in the vehicle. Maintain correct tire pressure. Check tire pressure regularly (when tires are cold). Remove snow tires when threat of snow or ice has ended. At highway driving speeds, fuel consumption will be lower with the air conditioning on and the windows closed


than with the air conditioning off and the windows open.


Using the onboard trip computer's fuel consumption modes can help you learn how to drive more economically.


Other factors that decrease gas mileage are:


Dirty air cleaner Dirty engine oil and clogged oil filter Dragging brakes Incorrect front end alignment Some of the above mentioned items and others are checked at the standard


maintenance intervals.


Avoid overheating the engine Do not drive at engine speeds above 4,500 rpm if you tow a trailer in hilly areas. This could cause the engine oil to overheat.


WARNING


Driving with the trunk open: Driving with the trunk open could lead to poisonous exhaust gases entering the passenger compartment. If the trunk must be kept open for any reason, proceed as follows:


Close the windows Set the ventilation system control to air flow to floor, windshield and side windows and the blower control to its


highest setting.


Weight distribution affects handling


At the specified curb weight your vehicle has a tendency to understeer, which means that the steering wheel has to be turned more than might seem appropriate for the curvature of a bend. This ensures good stability and reduces the risk of rear wheel skid. Remember that these properties can alter with the vehicle load. The heavier the load in the cargo area, the less the tendency to understeer.


Handling, roadholding


Vehicle load, tire design and inflation pressure all affect vehicle handling. Therefore,


133 06 Starting and driving


General information


check that the tires are inflated to the recommended pressure according to the vehicle load. See the "Tire pressure"


section. Loads should be distributed so that capacity weight or maximum permissible axle loads are not exceeded.


Driving through water


The vehicle can be driven through water up to a depth of approximately 9 in. (25 cm), at a maximum speed of 6 mph (10 km/h).


Take particular care when driving through flowing water. Clean the electrical connections for trailer wiring after driving in mud or water When driving through water, maintain low speed and do not stop in the water.


WARNING


After driving through water, press lightly on the brake pedal to ensure that the brakes are functioning normally. Water or mud can make the brake linings slippery, resulting in delayed braking effect.


CAUTION


Engine damage will occur if water is drawn into the air cleaner. If the vehicle is driven through water deeper than 9 in (25 cm), water may enter the differential and the


transmission. This reduces the oil's lubricating capacity and may shorten the service life of these components.


Do not allow the vehicle to stand in water up to the door sills longer than absolutely necessary. This could result


If the engine has been stopped while the car is in water, do not attempt to restart the engine. Have the car towed


in electrical malfunctions.


out of the water.


Cold weather precautions


If you wish to check your vehicle before the approach of cold weather, the following advice is worth noting:


Make sure that the engine coolant contains 50 percent antifreeze. Any other mixture will reduce freeze protection.


This gives protection against freezing down to - 31°F (-35°C). See section "Coolant". The use of "recycled" antifreeze is not approved by Volvo. Different types of antifreeze must not be mixed.


Volvo recommends using only genuine Volvo antifreeze in your vehicle's radiator. Your Volvo retailer stocks plenty


of Volvo engine coolant to help protect your vehicle during cold weather.


Try to keep the fuel tank well filled - this prevents the formation of condensation in the tank. In addition, in


extremely cold weather conditions it is worthwhile to add fuel line de-icer before refueling.


The viscosity of the engine oil is important. Oil with low viscosity (thinner oil) improves cold-weather starting as


well as decreasing fuel consumption while the engine is warming up. For winter use, 5W-30 oil, particularly the synthetic type1, is recommended. Be sure to use good quality oil but do not use cold-weather oil for hard driving or in warm weather. See page 257 for more information.


The load placed on the battery is greater during the winter since the windshield wipers, lighting, etc. are used more


often. Moreover, the capacity of the battery decreases as the temperature drops. In very cold weather, a poorly charged battery can freeze and be damaged. It is therefore advisable to check the state of


1Synthetic oil is not used when the oil is changed at the normal maintenance intervals except at owner request and at additional charge. Please consult your Volvo retailer.


134 06 Starting and driving


General information


charge more frequently and spray an antirust oil on the battery posts.


Volvo recommends the use of snow tires on all four wheels for winter driving - see the chapter "Wheels and tires." To prevent the washer fluid reservoir from freezing, add washer solvents containing antifreeze (see page 211 for the


location of the washer fluid reservoir). This is important since dirt is often splashed on the windshield during winter driving, requiring the frequent use of the washers and wipers. Volvo Washer Solvent should be diluted as follows: Down to 14° F (-10° C): 1 part washer solvent and 4 parts water Down to 5° F (-15° C): 1 part washer solvent and 3
parts water Down to 0° F (-18° C): 1 part washer solvent and 2 parts water Down to -18° F (-28° C): 1 part washer solvent and 1 part water.


Use Volvo Teflon Lock Spray in the locks.


NOTE


Avoid using de-icing sprays as they can cause damage to the locks.


Conserving electrical current


Keep the following in mind to help minimize battery drain:


When the engine is not running, avoid turning the ignition key to position II. Many electrical systems (the audio system, the optional navigation system, power windows, etc) will function with the ignition key in position I. This position reduces drain on the battery.


Please keep in mind that using systems, accessories, etc that consume a great deal of current when the engine is not


running could result in the battery being completely drained.


The optional 12 volt socket in the cargo area provides electrical current even with the ignition switched off, which


drains the battery.


NOTE


If the ignition is switched on, a warning message will be displayed in the text window in the instrument panel


when the battery charge is low.


An energy conserving function designed into the vehicle's electrical system will switch off certain functions or


reduce the load on the battery by, e.g., reducing the audio system's volume.


135 06 Starting and driving


General information


Before a long distance trip


It is always worthwhile to have your vehicle checked by a trained and qualified Volvo service technician before driving long distances. Your retailer or service technician will also be able to supply you with bulbs, fuses, spark plugs and wiper blades for your use in the event that problems occur.


As a minimum, the following items should be checked before any long trip:


Check that engine runs smoothly and that fuel consumption is normal. Check for fuel, oil, and fluid leakage Have the transmission oil level checked1. Check condition of drive belts. Check state of the battery's charge. Examine tires carefully (the spare tire as well), and replace those that are worn. Check tire pressures. The brakes, front wheel alignment, and steering gear should be checked by a trained and qualified Volvo service


technician only.


correct fuel.


snow tires.


Check all lights, including high beams. Reflective warning triangles are legally required in some states/provinces. Have a word with your Volvo retailer if you intend to drive in countries where it may be difficult to obtain the


Consider your destination. If you will be driving through an area where snow or ice are likely to occur, consider


1To prevent injury from contact with hot surfaces, do not inspect your vehicle's transmission fluid yourself. Have your vehicle's transmission fluid level inspected by a qualified Volvo service technician.


136 06 Starting and driving


Fuel requirements


Octane rating


MINIMUM


Volvo recommends premium for best performance, but using 87 octane or above will not affect engine reliability.


Volvo engines are designed to achieve rated horsepower, torque, and fuel economy performance using premium 91
octane fuel.


In demanding driving conditions, such as operating the vehicle in hot weather, towing a trailer, or driving for extended periods at higher altitudes than normal, it may be advisable to switch to higher octane fuel


RECOMMENDED


(91 or higher) or to change gasoline brands to fully utilize your engine's capacity, and for the smoothest possible operation.


NOTE


When switching to higher octane fuel or changing gasoline brands, it may be necessary to fill the tank more than once before a difference in engine operation is noticeable.


Deposit control gasoline (detergent additives)


Volvo recommends the use of detergent gasoline to control engine deposits. Detergent gasoline is effective in keeping injectors and intake valves clean. Consistent use of deposit control gasolines will help ensure good drivability and fuel economy. If you are not sure whether the gasoline contains deposit control additives, check with the service station operator.


NOTE


Volvo does not recommend the use of store-bought fuel injector cleaning additives.


Unleaded fuel


Each Volvo has a three-way catalytic converter and must use only unleaded gasoline. U.S. and Canadian regulations require that pumps delivering unleaded gasoline be labelled "UNLEADED". Only these pumps have nozzles which fit your vehicle's filler inlet. It is unlawful to dispense leaded fuel into a vehicle labelled "unleaded gasoline only". Leaded gasoline damages the three-way catalytic converter and the heated oxygen sensor system. Repeated use of leaded gasoline will lessen the effectiveness of the emission control system and could result in loss of emission warranty coverage. State and local vehicle inspection programs will make detection of misfueling easier, possibly


137 06 Starting and driving


Fuel requirements


resulting in emission test failure for misfueled vehicles.


NOTE


Some U.S. and Canadian gasolines contain an octane enhancing additive called methyl-cyclopentadienyl manganese tricarbonyl (MMT). If such fuels are used, your Emission Control System performance may be affected, and the Check Engine Light (malfunction indicator lamp) located on your instrument panel may light. If this occurs, please return your vehicle to a trained and qualified Volvo service technician for maintenance.


Gasoline containing alcohol and ethers


Some fuel suppliers sell gasoline containing "oxygenates" which are usually alcohols or ethers. In some areas, state or

Loading...
x