2005 Toyota Sienna Owners Manual

If the light stays on, it indicates that the front passenger airbag SRS driver and system and/or front passenger occupant classification system and “AIRBAG ON” and “AIRBAG OFF” indicator lights have a problem. If the light flashes, the SRS side airbag system and/or curtain shield airbag system have a problem. The SRS warning light and “AIRBAG OFF” indicator light will come on if there is a malfunction in the front passenger occu- pant classification system.

122

05 SIENNA_U (L/O 0409)

In the following cases, contact your Toyota dealer as soon as possible: D Any of the SRS side airbags and cur- tain shield airbags have been inflated. D The portion of the doors (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield airbags to inflate.

D The surface of the seats with the side airbag (shaded is scratched, cracked, or otherwise dam- aged.

illustration)

the

in

D The portion of

the front pillars, side pillars or roof side rail garnishes (pad- ding) containing the curtain shield air- bags inside (shaded in the illustration) is scratched, cracked, or otherwise damaged.

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classification sys- tem. This system detects the conditions 1—4 in the table on page 125 and based on these conditions activates or deacti- vates front passenger airbags. The sys- tem monitors the weight and load on the front passenger seat, and the seat belt buckle switch to determine condi- tions 1—4. In order for the system to detect the conditions correctly, do not do any of the following: D Apply a heavy load to the front pas- senger seat or equipment (e.g. seat- back table, grocery bag hooks, armrest or auxiliary box).

D Attach a commercial seatback

table, etc. to the front passenger seat seat- back.

D Put weight on the front passenger seat by putting your hands or feet on the seatback from the rear passenger seat.

The “AIRBAG ON” and “AIRBAG OFF” indicator lights indicate the actuation of the front passenger airbag, side airbag on the front passenger seat and front passenger’s seat belt pretensioner. The “AIRBAG OFF” indicator light will be illuminated when the ignition switch is in the “ON” position with the condition 2 in the table shown below.

If the front passenger occupant classifica- tion system determines that a person of adult size sits in the front passenger seat but the “AIRBAG OFF” indicator light is illuminated, one of the following is likely to have occurred: D A rear passenger lifts the front passen-

ger seat cushion with their legs.

D Objects are placed under the front pas-

senger seat.

D The

front passenger seatback

is

in

contact with the second seat.

is

illuminated when an adult

To ensure the system correctly detects an adult sitting in the front passenger seat, make sure the above do not occur. Make sure that the “AIRBAG ON” indicator light is seated in the front passenger seat. If the “AIRBAG OFF” indicator light is illumina- ted, ask the passenger to sit up straight, well back in the seat, and with the seat belt worn correctly. If the “AIRBAG OFF” indicator light still remains illuminated, ei- ther ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.

123

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

The “AIRBAG ON” and “AIRBAG OFF” indicator lights will be illuminated ini- tially when the ignition key is turned to the “ON” position. After about 4 sec- onds, they will go off. After that, the front passenger occupant classification system operates and judges which indi- cator light be illuminated.

indicator

light and “AIRBAG The SRS warning OFF” if there is a malfunction in the front pas- senger occupant classification system.

light will come on

124

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Condition and operation in the front passenger occupant classification system

Condition detected

by the front

passenger occupant classification system

1. Adult∗1
2. Child∗2 or child

restraint system∗3

3. Unoccupied

4. There is a

malfunction in the system

Indicator/warning light

Devices

“AIRBAG ON” and

“AIRBAG OFF” indicator lights

“AIRBAG ON”

“AIRBAG OFF”

Not illuminated

“AIRBAG OFF”

SRS warning

passenger’s

Front

light

Off

Off

Off

On

seat belt

reminder light

Flashing∗4
Flashing∗4

Off

Off

Front

passenger

airbag

Side airbag on the front passenger

seat

Curtain shield airbag in the

front

passenger

side

Front

passenger’s

seat belt

pretensioner

Activated

Activated

Deactivated

Deactivated

Deactivated

Activated

Deactivated

Activated

recognize him/her as a child depending on his/her physique and posture.

∗1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may ∗2: When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/her ∗3: Never install a rear−facing child restraint system on the front passenger seat. A forward−facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (See “Child restraint” on page 127 in this Section as for installing the child restraint system.)

as an adult depending on his/her physique or posture.

∗4: In the event that the front passenger does not wear a seat belt.

125

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

D Make

the

the

sure

If light

reconnect

passenger

seat. indicator

“AIRBAG ON” indicator light is illuminated when using the seat belt extender for the the front “AIRBAG OFF” is illuminated, disconnect the extender tongue from the seat belt buckle, then seat belt. Reconnect the seat belt extender after making sure the “AIRBAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIRBAG OFF” is illuminated, front passenger the airbag and side airbag on the front passenger side may not activate correctly, which could cause death or serious in the event of collision.

indicator

injury

light

CAUTION

To avoid potential death or serious injury when the front passenger occu- pant classification system does not detect the conditions correctly, ob- serve the following. D Do not recline the front passenger seat seatback so that it interferes with a second seat as it may cause the “AIRBAG OFF” light be illuminated. If the seatback inter- feres with the second seat, return the seatback to a position where it does not interfere with the second seat. Keep the front passenger seatback as upright as possible when the ve- hicle is moving. Reclining the seat- back excessively may lessen the ef- fectiveness of the seat belt system.

indicator

126

D If an adult sits

If

is

in

the

the

light

light should be

front passenger seat, the “AIRBAG ON” indicator illumi- “AIRBAG OFF” nated. indicator illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. the “AIRBAG OFF” indicator light still remains illumi- nated, either ask the passenger to move to the rear seat, or if that is not front the passenger seat fully rearward.

possible, move

If

the

D Wear the seat belt properly. D Make sure

front passenger’s seat belt tab has not been left in- serted into the buckle before some- one sits front passenger seat.

the

in

D Do not apply a heavy load to the front passenger seat or equipment (e.g. seatback table, grocery bag hooks, armrest or auxiliary box).

D Do not put weight on the front pas- senger seat by putting your hands or feet on the front passenger seat seatback from the rear passenger seat.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

The “AIRBAG ON” indicator light may be illuminated (the front passenger airbag and side airbag on the front passenger seat may deploy) even if observing the above cautions, when a child sits in, or a for- ward−facing is installed on the front passenger seat. Re- fer to all the cautions in “SRS airbags” on page 108 and “Child restraint” on page 127
in this Section.

restraint

system

child

D Do not let a rear passenger lift the front passenger seat with their feet or press on the seatback with their legs.

D Do not put objects under the front

passenger seat.

D Child restraint systems installed on the second seat should not contact the front seatbacks.

D When it is unavoidable to install the forward−facing child restraint sys- tem on the front passenger seat, install the child restraint system on the the proper order. (As for the installation order, see “—Installation with seat belt” on page 130 in this Section.)

front passenger seat

in

the

D Do not remove the front seats. D Do not kick

front passenger seat or subject it to severe impact. Otherwise, the SRS warning light may come on to indicate a malfunc- tion of the detection system. In this case, contact your Toyota dealer im- mediately.

Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- propriate child restraint systems for children. The laws of all 50 states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts” on page 96 in this Section for details.

CAUTION

D For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.

127

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

D Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, installed on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. D Never install a rear−facing child re- straint system on the front passen- ger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag can cause death or serious if the rear−facing child restraint system is installed on front passenger seat.

injury to the child

the

the

D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag considerable could speed and the child may be killed or seriously in- jured.

force. Otherwise,

inflate with

the area of

D On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the side window or the seat, front or side pillars or roof side rails from which the side air- bags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dan- gerous if the side airbag and cur- tain shield airbag inflate, and the impact could cause death or seri- ous injury to the child.

If

installing a child

D Do not use the seat belt extender when restraint system on the front or rear passen- ger seat. installing a child re- straint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of collision.

by

the

D Make sure that you have complied with all installation instructions pro- vided restraint manufacturer and that the system is properly secured. is not se- cured properly, it may cause death or serious injury to the child in the event of a sudden stop or accident.

child

If

it

128

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchor brackets for se- curing the top strap of a child restraint system. For instructions about how to use the an- chor bracket, see “—Using a top strap” on page 141 in this Section. The child restraint lower anchorages ap- proved for your vehicle may also be used. See “—Installation with child restraint low- er anchorages” on page 145 in this Sec- tion.

(A) Infant seat

—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap por- tion of the lap/shoulder belt. You must carefully consult the manufacturer’s instructions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. restraint system should be The child installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. When not using the child restraint system, keep it secured with the seat belt or place it somewhere other the passenger compartment. This will prevent it from in- juring passengers in the event of a sud- den stop or accident.

than

(B) Convertible seat

129

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Installation with seat belt

(C) Booster seat

(A) INFANT SEAT INSTALLATION An infant seat must be used in rear− facing position only.

CAUTION

D Never install a rear−facing child re- straint system on the front passen- ger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag could cause death or serious if the rear−facing child restraint system is installed on front passenger seat.

injury to the child

the

130

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Same angle

D Do not install a child restraint sys- tem on the second (or third) seat if it interferes with the lock mecha- nism of the front (or second) seats. Otherwise, the child or front (or second) seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

D If the driver’s seat position does not allow sufficient space for safe installation, re- straint system on the second right seat.

the child

install

D When

in

the

installing a child restraint system third seat center position, adjust both seatbacks to the same angle. Otherwise, the child restraint system cannot be se- curely this may cause death or serious injuries in a collision.

restrained and

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

131

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

CAUTION

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

132

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward−facing or rear−facing position de- pending on the age and size of the the child. When manufacturer’s the applicable age and size of the child as well as directions the child restraint system.

installing, follow instructions about

installing

for

133

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

light

indicator

illuminated when the ignition key

The “AIRBAG OFF” indicator light should be is “ON” and the child is in the child restraint system after following these procedures. The “AIRBAG OFF” indi- cates the SRS front passenger airbag and side airbag on the passenger side will not deploy. If the “AIRBAG ON” indicator light is illuminated, remove the child restraint system and reinstall it with the ignition key in the “ACC” or “LOCK” position. If the “AIRBAG ON” indicator light is illumi- nated when the ignition key is turned to the “ON” position, then the SRS front pas- senger airbag and side airbag on the pas- senger side may deploy in an accident. Do not drive the vehicle in this condition. Remove the child restraint system and contact your Toyota dealer.

6. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

7. Put a child on the child restraint sys- tem and secure the child, complying with the instructions provided by the child restraint system manufacturer.

Install the child restraint system on the front passenger seat only when it is un- avoidable. Your vehicle is equipped with a front passenger occupant classification system. In order to activate the occupant classification system correctly, install the forward−facing child restraint system on the front passenger seat in the following order: 1. Turn the ignition key to the “ON” posi-

tion.

2. Move the front passenger seat to the

rearward position.

3. Put the child restraint system on the front passenger seat without putting your weight on front passenger seat.

the

4. Insert the seat belt tab into the seat

belt buckle.

5. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended. To hold the seat securely, make sure the belt is in the lock mode before letting the belt retract.

134

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

CAUTION

the

D Never install a rear−facing child re- straint system on the front passen- ger seat. A forward−facing child re- straint system should only be installed on front passenger seat when unavoidable. If you must install the child restraint system on the front passenger seat, put the seat in its most rearward position, and install the forward−facing child restraint system in the proper or- der. Otherwise, the front passenger occupant classification system can not detect the presence of the child restraint system and the front pas- senger airbag and side airbag on the front passenger seat could deploy.

05 SIENNA_U (L/O 0409)

Move seat fully back

CAUTION

D Never install a rear−facing child re- straint system on the front passen- ger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag could cause death or serious if the rear−facing child restraint system is installed on front passenger seat.

injury to the child

the

the

D A forward−facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag could considerable speed and the child may be killed or seriously in- jured.

force. Otherwise,

inflate with

135

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

the area of

D On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the side window or the seat, front or side pillars or roof side rails from which the side air- bags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dan- gerous if the side airbag and cur- tain shield airbag inflate, and the impact could cause death or seri- ous injury to the child.

136

05 SIENNA_U (L/O 0409)

Same angle

D Do not install a child restraint sys- tem on the second (or third) seat if it interferes with the lock mecha- nism of the front (or second) seats. Otherwise, the child or front (or second) seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

D If the driver’s seat position does not allow sufficient space for safe installation, re- straint system on the second right seat.

the child

install

D When

in

the

installing a child restraint system third seat center position, adjust both seatbacks to the same angle. Otherwise, the child restraint system cannot be se- curely this may cause death or serious injuries in a collision.

restrained and

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

CAUTION

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt to retract.

137

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

05 SIENNA_U (L/O 0409)

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

138

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

CAUTION

(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.

Move seat fully back

the

D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag considerable could speed and the child may be killed or seriously in- jured.

force. Otherwise,

inflate with

the area of

D On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the side window or the seat, front or side pillars or roof side rails from which the side air- bags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dan- gerous if the side airbag and cur- tain shield airbag inflate, and the impact could cause death or seri- ous injury to the child.

139

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Same angle

CAUTION

D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.

D When

in

the

installing a child restraint system third seat center position, adjust both seatbacks to the same angle. Otherwise, the child restraint system cannot be se- curely this may cause death or serious injuries in a collision.

restrained and

140

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 96 in this Section for details.

could

D Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.

injuries due

D For child’s safety, do not place the

shoulder belt under child’s arm.

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Using a top strap (for second seats)

D If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

2. To remove the child restraint system, the buckle release button and

press allow the belt to retract.

Follow the procedure below for a child restraint system that requires the use of a top strap.

141

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Use the anchor brackets on the back of the second seats to attach the top strap. Anchor bracket is installed for each sec- ond seating position.

Anchor brackets

7−passenger models

Anchor brackets

8−passenger models

142

TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Using a top strap (for third seats)

3. Replace the head restraint.

Follow the procedure below for a child restraint system that requires the use of a top strap.

2. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint” on page 127 in this Section.

install

to

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

143

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Anchor brackets

Use the anchor brackets on the back of the third seats to attach the top strap. Anchor bracket is installed for right side and center seating position.

TO USE THE ANCHORAGES: 1. Remove the head restraint.

2. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint” on page 127 in this Section.

install

to

144

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Installation with child restraint lower anchorages (for second seats)

CAUTION

D Do not replace the head restraint when the child restraint system is installed. The head restraint may in- terfere with the top strap and the child restraint system can not be securely restrained. This may cause death or serious injuries in a colli- sion.

D Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.

7−passenger models

8−passenger models

The lower anchorages for the child re- straint systems complying with the FMVSS225 or CMVSS210.2 specifica- tions are installed in the rear seat. The anchorages are installed in the seat cushion of each second seat. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

145

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

5th lock position

1st lock position

SYSTEM

RESTRAINT

CHILD INSTALLATION 1. Fold down the seatback. The rear legs will disengage. Pushing seat downward on the back of the seat, make sure the rear seat legs are re- locked into place. Next pull back the seatback lock position (the most upright position). Then ad- just the seatback to the 5th lock position. Make sure locked securely.

the seat and seatback are

the 1st

to

146

Canada only

Canada only

Type A

Type B

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

2. Turn up the covers for the lower an- chorages. Confirm the position of the lower anchorages near the but- ton in the seat cushion.

3. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap (for second seats)” on page 141 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

05 SIENNA_U (L/O 0409)

—Installation with child restraint lower anchorages (for third seats)

CAUTION

D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

D After securing

the child restraint system, never slide or recline the seat.

D Do not install a child restraint sys- tem on the second seat if it inter- feres with the lock mechanism of the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

The lower anchorages for the child re- straint systems complying with the FMVSS225 or CMVSS210.2 specifica- tions are installed in the rear seat. The anchorages are installed in the clear- ance between the seat cushion and seat- back of the right and center seats. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

147

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

1st lock position

11th lock position

RESTRAINT

SYSTEM

CHILD INSTALLATION 1. Fold down

the seatback and pull back to the 1st lock position (the most upright position) until it locks into place. Adjust the seatback to the 11th lock position.

Make sure the seatback is locked secure- ly.

148

Canada only

Canada only

Type A

Type B

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

2. Widen

the gap between

the seat cushion and seatback slightly and confirm the position of the lower an- chorages.

3. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap (for third seats)” on page 143
in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

05 SIENNA_U (L/O 0409)

CAUTION

D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

D After securing

the child restraint

system, never recline the seat.

D Do not put a child restraint system on the third seat if it interferes with the lock mechanism of the second seats. Otherwise, the child or front (or second) seat occupant(s) may be killed or seriously in case of sudden braking or a colli- sion.

injured

149

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

150

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

SECTION 1− 4

OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt and telescopic steering wheel Outside rear view mirrors Anti−glare inside rear view mirror Auto anti−glare inside rear view mirror Vanity mirrors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

152
152
154
155
156

151

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Tilt and telescopic steering wheel

Outside rear view mirrors—

CAUTION

D Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

D After adjusting the steering wheel, try moving it up and down or for- ward and rearward to make sure it is locked in position.

To adjust the steering wheel position, push down the lock release lever. Then tilt the steering wheel to the desired angle, push or pull it to the desired steering column length and pull up the lock release lever.

152

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

in “AUTO” mode,

Vehicles with the auto anti−glare inside rear view mirror—On some models, when the inside rear view mirror surface dark- ens the outside rear view mirror surface also darkens to re- duce the reflection of the headlights of the vehicle behind you. (For details, see “Auto anti−glare inside rear view mirror” on page 155 in this Section.) On some models, when you push the rear window defogger switch, the heater panels in the outside rear view mirrors will quick- ly clear the mirror surface. (See “Rear window and outside rear view mirror de- foggers and windshield wiper de−icer” on page 169 in Section 1−5.)

CAUTION

D Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.

D On some models, since the mirror surfaces can get hot, do not touch them when the defogger switch is on.

05 SIENNA_U (L/O 0409)

—Power rear view mirror control

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch to “L” (left) or “R”

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

Mirrors can be adjusted when the key is in the “ACC” or “ON” position.

153

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Folding rear view mirrors

Anti−glare inside rear view mirror

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

The rear view mirrors can be folded backward for parking in compact areas. To fold the rear view mirrors, push back- ward.

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

154

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Auto anti−glare inside rear view mirror

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti− glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.

ignition key

the

is

to reduce

In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off the automatic function, push the “OFF” switch. To turn on the automatic function again, push the “AUTO” switch. Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it may take a little longer for the mirror to darken the detection of headlights.

in response

to

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

To ensure correct functioning of anti− glare mirror sensors located on both sides of the mirror, do not touch or cover the sensors with your finger or a piece of cloth, etc.

155

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Vanity mirrors

You can cancel the cut off operation by: D Turning the key to the “ACC” position. D Opening or closing any of front and

sliding doors.

D Turning off all the “ON” lights. All the lights are cut off when all the side doors and back door are locked by key or wireless remote control transmitter. The ignition switch must be turned off.

To use the vanity mirrors, swing down the sun visor and open the cover. On vehicles with the vanity lights, the light will come on when you open the cover. VANITY LIGHTS CUT OFF OPERATION When the ignition switch is turned off and vanity light stays lighting on, the light will cut off automatically after 20 minutes.

156

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

SECTION 1− 5

OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Headlight beam level control Emergency flashers Instrument panel light control Front fog lights Front personal lights Rear personal lights Luggage compartment light Ignition switch light Windshield wipers and washer Rear window wiper and washer Rear window and outside rear view mirror defoggers and windshield

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

158
161
162
163
163
164
165
166
166
167
168

wiper de−icer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

169

157

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Headlights and turn signals (without automatic light control system)

Daytime Running Light (DRL) system (all models sold in Canada and some models sold in U.S.A.) The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make the headlights come on when: D The ignition is on with the engine run-

ning.

D The knob is in the “OFF” position or

position 1.

D The parking brake is released. To turn off the DRL system, twist the knob to position 2 or turn the ignition switch off.

Position 2— The lights automatically turn off after 30
seconds when all the side doors and back door are closed with the ignition key in the “ACC” or “LOCK” position.

time before the headlights

” (lock) switch of the wireless If the “ remote control transmitter is pushed when all the side doors and back door are al- ready locked, the lights automatically turn off immediately. The turn off can be changed. For details, contact your Toyota dealer. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Automatic light cut off system Position 1— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position.

the

158

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Headlights and turn signals (with automatic light control system)

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Position 3 (“AUTO”)—Headlights and/or all of the lights in position 1
They automatically turn on or off depend- ing on the darkness of the surroundings. Manually twist the knob to the position 2
to turn on the headlights if they are need- ed immediately when entering a dark tun- nel, parking structure, etc.

the

159

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Position 2 or 3 with the headlights on— The lights automatically turn off after 30
seconds when all the side doors and back door are closed with the ignition key in the “ACC” or “LOCK” position.

time before the headlights

” (lock) switch of the wireless If the “ remote control transmitter is pushed when all the side doors and back door are al- ready locked, the lights automatically turn off immediately. The turn off can be changed. For details, contact your Toyota dealer. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

top of

the driver’s side

The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. Automatic light cut off system Position 1 or position 3 with the tail lights on— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position.

160

Daytime Running Light (DRL) system (all models sold in Canada and some models sold in U.S.A.) The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make the headlights come on when: D The ignition is on with the engine run-

ning.

is

D The knob

“OFF” position, position 1 or position 3 with the tail lights on.

the

in

D The parking brake is released. To turn off the DRL system, twist the knob to position 2 or position 3 with the head- lights on, or turn the ignition switch off.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Headlight beam level control

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

To adjust the headlight beam level, turn the dial. The following list shows examples of prop- er dial settings. For loading conditions oth- er than those listed, adjust the dial posi- tion so that the beam level is the same as the one obtained according to the list when only the driver is in the vehicle. The higher the number of the dial position, the lower the headlight beam level. Always keep the headlight beam at the proper level, or your headlights may dazzle other road users.

161

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Emergency flashers

Loading condition and dial position

Loading conditions

Variations

7−passenger

models

8−passenger

models

Driver only, or Driver + one passenger in the front seat

Driver + one passenger in the front seat and all passengers in the second seat

All passengers