2002 Toyota Sienna Owners Manual

(b) Overdrive switch You can select either third gear (with overdrive off) or fourth gear (with over- drive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will automatically be on.

for better

148

02 SIENNA_U (L/O 0107)

For ways to decrease the vehicle speed, see “Cruise control” in this section.

NOTICE

CAUTION

Be careful when downshifting on a slippery shifting could cause the vehicle to spin or skid.

surface. Abrupt

(e) Using “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in first gear and automatically shift to second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.

z Be careful not to over−rev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference:

“2” “L”

. . . . . . . . . . . . . . . . . . . . . . .

120 km/h (74 mph) 64 km/h (40 mph) z Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmission dam- age from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.

(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.

NOTICE

Never shift into reverse while the ve- hicle is moving.

(g) Parking 1. Bring the vehicle to a complete stop. 2. With

the brake pedal pressed down, fully depress the parking brake pedal to apply the parking brake securely.

3. With

the brake pedal pressed down, shift the selector lever to the “P” posi- tion.

CAUTION

Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.

(h) Good driving practice D If the transmission repeatedly shifts up and down between third gear and over- drive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately after- ward.

D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.

2002 MY SIENNA_U (OM45407U)

149

02 SIENNA_U (L/O 0107)

NOTICE

to

the

If you rock your vehicle, observe the following precautions to prevent dam- age transmission and other parts. z Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.

z Do not race the engine and avoid

spinning the wheels.

z If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.

CAUTION

Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.

NOTICE

Do not hold the vehicle on an up- grade with the accelerator pedal. It can cause the transmission to over- heat. Always use the brake pedal or parking brake.

(i) Rocking your vehicle if stuck

CAUTION

If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward. Do not attempt this procedure if people or objects are anywhere near the ve- hicle. During the rocking operation the vehicle may suddenly move for- ward or backward as it becomes un- stuck, causing injury or damage to nearby people or objects.

150

2002 MY SIENNA_U (OM45407U)

Traction control system The traction control system automatical- ly helps prevent the spinning of front wheels when the vehicle is started or accelerated on slippery road surfaces. When the ignition key is turned to “ON”, the system automatically turns on.

CAUTION

Under certain slippery road condi- tions, full traction of the vehicle and power against front wheels cannot be maintained, even though the traction control system is in operation. Do not drive the vehicle under any speed or maneuvering conditions which may cause traction control. In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tire chains. Always drive at an appropriate and cautious speed the present road condi- tions.

the vehicle

tires or

lose

for

to

02 SIENNA_U (L/O 0107)

When the traction control system is oper- ating, the following conditions occur: D The system controls the spinning of the front wheels. At this time, the slip indi- cator light blinks.

D You may feel vibration or noise in your the is

vehicle, caused by operation of brakes. This functioning properly.

the system

indicates

The slip indicator light comes on for a few seconds when the ignition key is turned to “ON”. If the indicator light does not come on when the ignition is turned on, contact your Toyota dealer.

that

NORMAL DRIVING MODE Leave the system on during the ordi- nary driving so it can operate when needed. You may hear a sound the engine compartment for a few seconds when the engine is started or just after the vehicle is started. This means that the traction control system is in the self−check mode, but does not indicate a malfunction.

in

2002 MY SIENNA_U (OM45407U)

151

02 SIENNA_U (L/O 0107)

to “ON”.

“TRAC OFF” indicator light comes on for a few seconds when the ignition key is turned It will come on again when you push the “TRAC OFF” switch to turn off the system. In the following cases, contact your Toyota dealer: D The indicator light does not come on when the ignition key is turned “ON”. D The indicator light remains on after the

ignition is turned on.

D The indicator light comes on with the

normal driving mode while driving.

“VSC” warning light This light warns that there is a problem somewhere in the traction control system or the vehicle skid control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.

TRACTION CONTROL OFF MODE If your wheels get stuck in a ditch when you are driving on a severe off road and sand, turn off the traction control system. This system that con- trols engine performance interferes with the process of freeing your wheels. To turn off: Push “TRAC OFF” switch. The “TRAC OFF” indicator light will come on. To turn on: Push “TRAC OFF” switch once again. The “TRAC OFF” indicator light will go off.

152

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the

ignition key is turned to “ON”.

D The warning light comes on while driv-

ing.

Vehicle skid control system The vehicle skid control system helps provide integrated control of the sys- tems such as an anti−lock brake sys- tem, brake assist system, traction con- trol, engine control, etc. This system automatically controls the output of the brakes or engine to help prevent the vehicle from skidding when cornering on a slippery road surface or abrupt steering wheel operation occurs. This system activates when the vehicle speed than 15 km/h (9
mph). You may hear a sound the engine compartment for a few seconds when the engine is started or just after the vehicle is started. This means that the system is in the self−check mode but does not indi- cate a malfunction.

is about more

in

CAUTION

light

indicator

D Do not rely excessively on the ve- hicle skid control system. Even if the vehicle skid control system is operating, you must always drive carefully and attentively to avoid serious injury. Reckless driving will result in an unexpected accident. If the slip flashes, sounding an alarm sounds, special care should be taken while driving. D Only use tires of specified size. The size, manufacture, brand and tread pattern for all 4 tires should be the same. If you use the tires other than specified, or different type or size, the vehicle skid control sys- tem may not function correctly. When replacing the tires or wheels, (See contact your Toyota dealer. “Checking and replacing tires” in Section 7−2.)

2002 MY SIENNA_U (OM45407U)

153

02 SIENNA_U (L/O 0107)

In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the

ignition key is turned to “ON”.

D The warning light comes on while driv-

ing.

If the vehicle is going to skid during driv- ing, the slip indicator light blinks and an alarm sounds intermittently. Special care should be taken while driving. The slip indicator light comes on for a few seconds when the ignition key is turned to “ON”. If the indicator light does not come on when the ignition is turned on, contact your Toyota dealer.

“VSC” warning light This light warns that there is a problem somewhere in the vehicle skid control sys- tem or the traction control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.

154

2002 MY SIENNA_U (OM45407U)

Tire pressure warning system The tire pressure warning system is de- signed to provide warning when tire pressure of any one of the tires is criti- cally reduced while the vehicle is mov- ing. The low tire pressure warning light comes on to inform you that such low tire pressure may hamper driving. This system is not designed to operate when the vehicle is stopped. Therefore, check regularly. The recommended cold tire pressures, tire size and the vehicle capacity weight are on the tire pressure label. (For instruction, see “Checking tire pressure” in Section 7−2.) Installed tires should be of the specified size. They should be of the same size and construction. If tires other than of the specified size are used, or if tires of dif- ferent sizes or constructions are mixed, the tire pressure warning system will not function properly.

tire pressures

the

02 SIENNA_U (L/O 0107)

The tire pressure warning system does not function properly under certain cir- cumstances. In the following cases, the low tire pressure warning light may not come on even if the tire pressure is low, or it may come on when the tire pressure is actually normal. D The tread wear is uneven among the

installed tires.

D A compact spare tire, snow tires, or

tire chains are used.

D The tire pressure is excessively higher than specified, or tire pressure is sud- denly reduced due to bursts or other causes.

D The vehicle

is driven on a slippery road surface such as rough road and frozen road.

D The vehicle speed is less than 30 km/h (19 mph) or more than 100 km/h (62
mph), and the driving duration is less than 5 minutes.

LOW TIRE PRESSURE WARNING LIGHT This light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is func- tioning properly. If the low tire pressure warning light tire comes on while driving, adjust pressure to the specified level. (See “Tires” in Section 8.) After the light should go off after driving at about more than 30 km/h (19 mph) for some time. If the light still remains, have the tire pressure warning system checked at your Toyota dealer.

tire pressure is adjusted,

the

2002 MY SIENNA_U (OM45407U)

155

02 SIENNA_U (L/O 0107)

Parking brake

4. With the vehicle stopped, push the re- set switch on the left lower instrument panel and hold tire pressure warning light blinks for three times.

it until

low

the

5. The initial adjustment is completed af- ter driving at the speeds of 30 km/h (19 mph) or over total 8
hours, when the tire pressure warning system detects the normal tire pressur- es.

for about

the

low

Do not push the reset switch without ad- justing the tire pressure to the specified level. Otherwise, tire pressure warning light may not come on even if the tire pressure is low, or it may come on when the tire pressure is actually normal. If you push the reset switch while the vehicle is moving, the initial adjustment is not performed. If the low tire pressure warning light does not blink when you push and hold the reset switch, have the low pressure warn- ing system checked at your Toyota dealer.

the present

TIRE PRESSURE WARNING SYSTEM RESET SWITCH Pushing this reset switch after replac- ing or rotating tires or wheels memo- ries tire condition as a standard. After replacing or rotating tires or wheels, perform the initial adjustment as follows. 1. Park the vehicle at a safe place and apply the parking brake. Stop the en- gine.

the

2. Adjust pressures of all

installed tires to the specified level. (See “Tires” in Section 8.)

the

3. Turn the ignition key to “ON”. 156

2002 MY SIENNA_U (OM45407U)

Type A

Type B

02 SIENNA_U (L/O 0107)

When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Fully depress the parking brake pedal. For better holding power, first de- press the brake pedal and hold it while setting the parking brake. To release: Depress pedal once again. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.

the parking brake

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

Cruise control The cruise control allows you to cruise the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off the accelerator pedal. Your cruising speed can be maintained up or down grades within the limits of engine performance, although a slight speed change may occur when driving up or down the grades. On steeper hills, a greater speed change will occur so it is better to drive without the cruise control.

CAUTION

D To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.

If

D Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

TURNING ON THE SYSTEM To operate the cruise control, press the “CRUISE ON−OFF” button. This turns the system on. The the instrument panel shows that you can now set the vehicle at a desired cruising speed. Another press will turn the system completely off.

indicator

light

in

CAUTION

To avoid accidental cruise control en- gagement, keep the “CRUISE ON− OFF” switch off when not using the cruise control.

2002 MY SIENNA_U (OM45407U)

157

02 SIENNA_U (L/O 0107)

If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration. CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling the lever in the “CANCEL” di-

rection and releasing it. b. Depressing the brake pedal.

If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto- matically cancel out. If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset speed will also automatically cancel out. If the preset speed automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity.

RESETTING TO A FASTER SPEED Push the lever up in the “RES/ACC” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “SET/COAST” direction. RESETTING TO A SLOWER SPEED Push the lever down in the “SET/COAST” direction and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “SET/COAST” direction. Even if you turn off the overdrive switch, with the cruise control on, engine braking will not be applied because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. the brake pedal, cruise control is cancelled.

If you use

SETTING AT A DESIRED SPEED The transmission must be in “D” before you set the cruise control speed. Bring your vehicle to the desired speed, push the lever down in the “SET/COAST” direction and release it. This sets the ve- hicle at that speed. If the speed is not satisfactory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your foot off the accelerator pedal.

158

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

lever or by depressing

RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal or clutch pedal, pushing the lever up in the “RES/ACC” direction will restore the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARNING If the instrument cluster flashes when using the cruise control, press the “CRUISE ON− OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. D The indicator light does not come on. D The indicator light flashes again. D The

light goes out after

“CRUISE”

indicator

indicator

light

the

in

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

2002 MY SIENNA_U (OM45407U)

159

02 SIENNA_U (L/O 0107)

160

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

SECTION 1− 7

OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Audio remote controls Car audio system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

162
163
180
182

2002 MY SIENNA_U (OM45407U)

161

02 SIENNA_U (L/O 0107)

Reference

Type 1−1: AM·FM ETR radio/cassette play- er/compact disc player (with compact disc changer controller)

Type 1−2: AM·FM ETR radio/cassette play- er/compact disc player (with compact disc auto changer controller)

Type 2: AM·FM ETR radio/cassette player/ compact disc auto changer

162

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “AM”, “FM1·2”, “TAPE” or “CD” to turn on function without pushing “PWR·VOL”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM1·2”, “TAPE” or “CD” if the system to switch from one function to another.

is already on but you want

that

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

YOUR RADIO ANTENNA Mast type antenna—To remove an anten- na, carefully turn it counterclockwise.

NOTICE

z Mast type antenna:

To prevent damage to the antenna, make sure is removed before driving your Toyota through an au- tomatic car wash.

it

z On−glass antenna (built−in on the

rear window glass): Attaching the film (especially con- ductive or metallic type) on the rear glass will noticeably the sensitivity of the radio.

reduce

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

2002 MY SIENNA_U (OM45407U)

163

02 SIENNA_U (L/O 0107)

YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Type 1−1 and 1−2 only— Then it will play from track 1 again. Type 2 only— The next disc will be played from track 1. The “LOAD” button must be pressed to insert a disc. (See “LOAD” button.)

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

164

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

—Controls and features "Type 1−1

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

2002 MY SIENNA_U (OM45407U)

165

02 SIENNA_U (L/O 0107)

"Type 1−2

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

166

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature.

fast

the

the

Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. CONTROL / MODE (Audio control and mode adjustment) Type 1−1
Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”.

/ MODE”

to adjust

low−pitch

is used

range

from

tone

the

2002 MY SIENNA_U (OM45407U)

167

02 SIENNA_U (L/O 0107)

tone

is used

low−pitch

to adjust

AUDIO (Audio control and mode adjust- ment) Type 1−2
Manual tone adjustment function— This knob the manually. tone adjustment, push For “AUDIO” repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”. For middle−pitch tone adjustment, push “AUDIO” repeatedly until “MID” appears on the display. Then turn the knob to suit your preference. The display will show the range from “MID −5” to “MID 5”. For high−pitch tone adjustment, push “AUDIO” repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”.

range

range

from

from

the

the

the

from

range

to adjust

is also used

Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “AUDIO” repeatedly until “FAD” appears on the dis- play. Then turn the knob to adjust the front/rear balance. The display will show “FAD−F7” to “FAD−R7”. For left/right adjustment, push “AUDIO” re- peatedly until “BAL” appears on the dis- play. Then turn the knob to adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer.

time you push “CD”,

range

from

the

the

from

turn

range

/ MODE”

the display. Then

For middle−pitch tone adjustment, push “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId −5” to “MId 5”. For high−pitch tone adjustment, push “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd−F7” to “FAd−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on turn to adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”.

the display. Then

the display. Then

is also used

to adjust

the knob

the knob

range

range

from

from

the

168

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

inserted up−side down. Clean

If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer.

loaded

inside

it the

is

B NR∗

DISC ƝƜ Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation.

FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button. If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random): Compact Disc Player There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. To randomly play the tracks on a disc: ” Quickly push and release “ will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push this button again.

listen

the

”. “

to

2002 MY SIENNA_U (OM45407U)

169

in the

Compact disc auto changer only— To randomly play all the tracks magazine: ” until you hear a Push and hold “ beep. “ ” will appear on the dis- play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push this button again. RPT (Repeat) Cassette Player

the

track

” while

is playing. Push “ “ ” will appear on the display. When the track ends, it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

02 SIENNA_U (L/O 0107)

Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: ” while the Quickly push and release “ ” will appear on the track is playing. “ display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: ” until you hear a Push and hold “ beep. “ ” will appear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 se- conds, and then scan again. To select a station, push “SCAN” again.

170

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push ·SCAN” will appear on the display and “ the player will perform the first track of the next disc. To select a disc, push the “SCAN” again. If the player has scanned all the discs, it will stop scanning.

the seek mode,

the radio finds and the next station up or down the

SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display.

If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

2002 MY SIENNA_U (OM45407U)

171

02 SIENNA_U (L/O 0107)

TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

172

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

"Type 2

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

2002 MY SIENNA_U (OM45407U)

173

02 SIENNA_U (L/O 0107)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button)

the cassette

tape eject button to

Cassette tape Push eject a cassette. After you turn the ignition to “LOCK”, you will be able to eject a cassette, but you will not be able to reinsert it.

Compact disc To eject one compact disc only: Push and release the compact disc eject button. If you hold the button too long (if the audio system is on at this time, you hear a beep.), the mechanism will change to the mode for ejecting all the discs loaded in the changer. You can also eject any spe- cific one of the discs loaded in the chang- er as follows:

1. Push either side of the “DISC” button until the number of the disc you want to eject is displayed.

2. Push and release the compact disc

eject button.

To eject all the discs loaded in the chang- er: Push and hold the compact disc eject button (until you hear a beep when the audio system is on). The last compact disc played before pushing the button will be ejected first. If a disc is left in the slot for a long time, the function to eject all the discs will be automatically cancelled. After you turn the ignition to “LOCK”, you will be able to eject one compact disc only or all the discs loaded in the chang- er, but you will not be able to reinsert it or them.

174

2002 MY SIENNA_U (OM45407U)

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature.

fast

the

the

02 SIENNA_U (L/O 0107)

Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. For tone adjustment, push “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”.

/ MODE”

to adjust

low−pitch

is used

range

from

tone

the

the

turn

from

range

/ MODE”

the display. Then

For middle−pitch tone adjustment, push “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId −5” to “MId 5”. For high−pitch tone adjustment, push “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd−F7” to “FAd−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on turn to adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”.

the display. Then

the display. Then

is also used

to adjust

the knob

the knob

range

range

from

from

the

CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. If the player or another unit equipped with the player malfunctions, your audio system will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc.

inserted up−side down. Clean

loaded

inside

it the

is

2002 MY SIENNA_U (OM45407U)

175

02 SIENNA_U (L/O 0107)

If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC ƝƜ By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display.

B NR∗

Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button. If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation.

LOAD This button is used to load the compact discs in the compact disc auto changer which is integrated with the radio and cas- sette player. This compact disc auto changer can store up to 6 discs. The key must be in the “ACC” or “ON” position. Loading one compact disc only— To load one compact disc only, quickly push and release the button. If you hold the button too long (if the audio system is on at this time, you hear a beep.), the mechanism will change to the mode for loading multiple compact discs. After pushing the button, insert a compact disc. At this time, the indicators on both sides of the slot are flashing. After the disc is loaded, the shutter of the slot will close and the indicators will stop flashing. If no compact disc is inserted, the shutter will close after 15 seconds.

176

2002 MY SIENNA_U (OM45407U)

Loading multiple compact discs— To load multiple compact discs, push and hold (until you hear a beep when the au- dio system is on). After pushing the but- ton, insert the first compact disc. At this time, the indicators on both sides of the slot are flashing. After the disc is loaded, the shutter of the slot will close and the indicators will stop flashing. After a few seconds, the shutter will automatically open again so the next disc can be in- serted. The same process can be applied for loading the rest of the discs. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random): Compact Disc Player There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order.

listen

the

to

02 SIENNA_U (L/O 0107)

”. “

To randomly play the tracks on a disc: ” Quickly push and release “ will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push this button again. To randomly play all magazine: ” until you hear a Push and hold “ beep. “ ” will appear on the display and the player will perform all the tracks on all the discs in the magazine in ran- dom order. To turn off the random feature, push this button again. RPT (Repeat) Cassette Player

the tracks

in the

the

track

” while

is playing. Push “ ” will appear on the display. When “ the it will automatically be track ends, rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: ” while the Quickly push and release “ ” will appear on the track is playing. “ display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Repeating a disc: ” until you hear a Push and hold “ ” will appear on the display. beep. “ The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.

2002 MY SIENNA_U (OM45407U)

177

02 SIENNA_U (L/O 0107)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 se- conds, and then scan again. To select a station, push “SCAN” again.

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push ·SCAN” will appear on the display and “ the player will perform the first track of the next disc. To select a disc, push the “SCAN” again. If the player has scanned all the discs, it will stop scanning.

178

2002 MY SIENNA_U (OM45407U)

the seek mode,

the radio finds and the next station up or down the

SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display.

02 SIENNA_U (L/O 0107)

TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

2002 MY SIENNA_U (OM45407U)

179

If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

Audio remote controls

02 SIENNA_U (L/O 0107)

Some parts of the audio system can be adjusted with the buttons on the steering wheel. Details of the specific buttons, controls, and features are described below. 1. “Ɯ” and “VOL Ɲ” Buttons 2. “MODE” Button 3. “no” Button 4. “MUTE” Button

180

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

1. “Ɯ” and “VOL Ɲ” Buttons (Volume

Up/Down)

to

increase while

to increase the volume. The the

Push “Ɯ” volume continues button is being pressed. Push “VOL Ɲ” to decrease the volume. The volume continues to decrease while the button is being pressed. 2. “MODE” Button Push “MODE” to select an audio mode. Each push changes the mode sequentially if the desired mode is ready to use. 3. “no” Button (Seek, Search, Track) Radio In plays down the station band. To seek a station, push the “n” or “o” side of the button. Do this again to find the next station. If you push the button on either side dur- ing the seek mode, seeking will be can- celled. Cassette player By using this button, you can skip to a different track in either direction. You can skip up to nine tracks at a time.

the radio finds and the next station by going up or

the seek mode,

Push the “n” or “o” side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the track you want to listen to is set. If you push the button ten times, the skip function will turn off. When counting the number of the tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two before the song you are listening to, push the “o” side of the button three times. If you push the track button further than you wanted to, push the other side of the button. The track number will be increased or reduced. The track number you select is not valid if the tracks remaining on the current side of the cassette. D When the tape reaches to the begin- ning, the player will automatically start playing that side.

the number of

is higher

than

it

There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken, live, or classical recordings. Compact disc player By using this button, you can skip to a different track in either direction. Push either side of the track button until the track you want to listen to is set. If you want to return to the beginning of the current track, push the “o” side of the button once, quickly. 4. “MUTE” Button Push “MUTE” to turn the volume off mo- mentarily. This is cancelled by doing the following: D Push “MUTE” once again. D Push “Ɯ” or “VOL Ɲ”. D Operate any of the buttons or knobs on

function

the audio system itself.

D Disconnect the electrical power source.

D After the tape reaches to the end, the reverse and

player will automatically start playing the other side.

2002 MY SIENNA_U (OM45407U)

181

02 SIENNA_U (L/O 0107)