2002 Toyota Sienna Owners Manual

from

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt to retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

106

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the convertible seat, press the buckle−release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward−fac- ing position only.

2002 MY SIENNA_U (OM45407U)

107

02 SIENNA_U (L/O 0107)

Move seat fully back

CAUTION

D A forward−facing child restraint sys- tem should be allowed to be put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of the deploying airbag could cause death or serious injury to the child.

D On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. It is dan- gerous if the side airbag inflates, and the impact could cause death or serious injury to the child.

108

2002 MY SIENNA_U (OM45407U)

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.

insert

the

tab

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.

02 SIENNA_U (L/O 0107)

D If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

2. To remove the child restraint system, press the buckle−release button and al- low the belt to retract.

2002 MY SIENNA_U (OM45407U)

109

CAUTION

D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.

to do so could reduce

D Both high−positioned lap belts and loose−fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on a child’s hips as possible.

D For child’s safety, do not place the

shoulder belt under child’s arm.

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

02 SIENNA_U (L/O 0107)

—Using a top strap

Follow the procedure below for a child restraint system that requires the use of a top strap.

Anchor brackets

Second seat (left side only)

Third seat

110

2002 MY SIENNA_U (OM45407U)

Second seat (left side only): Use the an- chor bracket on the floor to attach the top strap. Anchor bracket is installed for left side second seat. Third seat: Use the anchor brackets on the back of the third seat cushion to at- tach the top strap. Anchor brackets are third seating position.

for each

installed

02 SIENNA_U (L/O 0107)

2. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

Second seat (left side only)—Before latch- ing the hook, make sure the anchor brack- et is in the correct direction as shown in the illustration. For the child re- straint system, see “Child restraint” in this section.

instructions

install

to

TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.

Second seat (left side only)

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

Third seat

2002 MY SIENNA_U (OM45407U)

111

02 SIENNA_U (L/O 0107)

—Installation with child restraint lower anchorages

3. Replace the head restraint.

Second bench seat without built−in child restraint system (left side only)

Third seat (right side only)

interfaced with

The lower anchorages for the child re- straint system the FMVSS225 specification are installed in the rear seat. The anchorages are installed in the clear- ance between the seat cushion and seat- back of the rear seat as shown in the illustration. Child restraint system interfaced with the FMVSS225 specification can be fixed with these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

112

2002 MY SIENNA_U (OM45407U)

Captain seat (left side only)

02 SIENNA_U (L/O 0107)

RESTRAINT

SYSTEM

CHILD INSTALLATION Type A— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages in the seat cushion.

2. Latch the hooks of lower straps onto the anchorages and tighten the lower straps. Type B— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages in the seat cushion.

2. Latch the buckles onto the anchor-

ages.

it should be anchored. (For

If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” in this section.) For to the instruction manual equipped with each product.

the installation details, refer

Type A

Type B

2002 MY SIENNA_U (OM45407U)

113

02 SIENNA_U (L/O 0107)

Tilt steering wheel

CAUTION

D Do not adjust the steering wheel while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.

D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

CAUTION

D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

D After securing

the child restraint system, never slide or recline the seat.

D Do not put a child restraint system on the second seat or third seat if it interferes with the lock mecha- nism of the front seat or second seat. This can cause severe injury to the child and front passenger in case of sudden braking or a colli- sion.

To change the steering wheel angle, hold the steering wheel, pull the lock release lever toward you, tilt the steer- ing wheel to the desired angle and re- lease the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.

114

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Outside rear view mirrors—

—Power rear view mirror control

CAUTION

D Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.

D On some models, since the mirror surfaces can get hot, keep your hands off them when the defogger switch is on.

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror. On some models, when you push the rear window defogger switch, the heater panels in the outside rear view mirrors will quick- ly clear the mirror surface.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push the “L” (left) or “R” (right) switch.

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

Mirror can be adjusted when key is in the “ACC” or “ON” position.

2002 MY SIENNA_U (OM45407U)

115

02 SIENNA_U (L/O 0107)

—Folding rear view mirrors

Anti−glare inside rear view mirror

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.

for parking

The rear view mirrors can be folded backward restricted areas. To fold the rear view mirrors, push back- ward.

in

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

116

2002 MY SIENNA_U (OM45407U)

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.

02 SIENNA_U (L/O 0107)

Auto anti−glare inside rear view mirror

to reduce

In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off the automatic function, push the “MIRROR” switch. To turn on the automatic function again, push the “MIRROR” switch. Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it for the mirror to may take little longer darken to the detection of headlights.

in response

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.

function

is designed

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. to reduce This glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.

ignition key

the

is

2002 MY SIENNA_U (OM45407U)

117

02 SIENNA_U (L/O 0107)

Sun visors—

—Vanity mirrors

CAUTION

Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover the anti−glare inside rear view mirror and obstruct the rear view.

To block out glare, move the sun visor. To block out glare from the front—Swing down the sun visor (position 1). To block out glare from the side—Swing down the sun visor, remove it from the hook and swing it to the lateral side (posi- tion 2). If glare comes from obliquely behind you, extend the plate at the end of the visor (to position 3).

118

2002 MY SIENNA_U (OM45407U)

To use the vanity mirrors, swing down the sun visor and open the cover. On some models, the vanity light comes on when you open the cover. VANITY LIGHTS CUT OFF OPERATION When is “OFF” and vanity light in the vehicle stays lighting on, the light will cut off automatically after 30 minutes.

ignition switch

the

02 SIENNA_U (L/O 0107)

You can cancel the cut off operation by: D Turning the key to the “ACC” position. D Opening or closing any of front and

sliding doors.

the

lights are cut off when all

D Turning off all the “ON” lights. All the doors are locked by key or wireless re- mote control transmitter. The key must be in the “OFF” position.

2002 MY SIENNA_U (OM45407U)

119

02 SIENNA_U (L/O 0107)

120

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

SECTION 1− 4

OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Personal lights Interior light Ignition switch light Luggage compartment light Windshield wipers and washer Rear window wiper and washer Rear window and outside rear view mirror defoggers

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

122
125
125
126
126
128
129
130
131
131
132

2002 MY SIENNA_U (OM45407U)

121

02 SIENNA_U (L/O 0107)

Headlights and turn signals (with automatic light control system)

top of

the driver’s side

The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor.

“LOCK” position. To

The lights automatically turn off when ei- ther front doors or sliding doors are opened with the ignition key in the “ACC” or them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

turn

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

the

Daytime running light system The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Position 3 (“AUTO”)—Headlights and/or all of the lights in position 1
They automatically turn on or off depend- ing on the darkness of the surroundings. Manually twist the knob to the position 2
to turn on the headlights if they are need- ed immediately when entering a dark tun- nel, parking structure, etc.

the

122

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Headlights and turn signals (without automatic light control system)

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above The lights automatically turn off when ei- ther front doors or sliding doors are opened with the ignition turned off. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

the

2002 MY SIENNA_U (OM45407U)

123

02 SIENNA_U (L/O 0107)

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

the

Daytime running light system The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

124

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Emergency flashers

Instrument panel light control

NOTICE

To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

To adjust the brightness of the instru- ment panel lights, turn the dial.

2002 MY SIENNA_U (OM45407U)

125

02 SIENNA_U (L/O 0107)

Front fog lights

Personal lights

To turn on the front fog lights, twist the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam.

Front (with moon roof) The front personal lights operate sepa- rately with each lens. To turn on the light, push the lens on your side. To turn the light off, push the lens once again.

126

2002 MY SIENNA_U (OM45407U)

Front (without moon roof) The front personal lights operate sepa- rately with each lens. To turn on the light, push the lens on your side. To turn the light off, push the lens once again. To turn on the front personal push the switch. The following positions: “OFF”—Turns the light off. “DOOR”—Turns the light on when either front or sliding door is opened.

light switch has the

front personal

lights,

02 SIENNA_U (L/O 0107)

the

OFF

CUT

LIGHTS

PERSONAL OPERATION When the ignition switch is “OFF” and any personal lights in the vehicle stay lighting on, lights will cut off automatically after 30 minutes. You can cancel the cut off operation by: D Turning the key to the “ACC” position. D Opening or closing any of the doors. D Turning off all the “ON” lights. All the lights are turned off when all the doors are locked by the key or wireless remote control transmitter. The key must be in the “OFF” position.

ILLUMINATED ENTRY SYSTEM Front (with moon roof)— The light comes on when either front or sliding doors are opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. Front (without moon roof) and center— With the switch in the “DOOR” position, the light comes on when either front or sliding door is opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. However, in the following cases, the light goes out immediately: D All the doors are closed when the igni- tion key is in “ACC” or “ON” position. D All the doors are locked when the light

is still on.

D One door will be closed with the lock knob pushed forward (front door) or downward (sliding door) while the other doors are locked.

When the driver’s door is unlocked with a key, the light comes on for 15 seconds, even if the doors are not opened.

Center The center personal lights operate sep- arately with each lens. To turn on the light, push the lens on your side. To turn the light off, push the lens once again. To turn on the center personal lights, slide the switch. The center personal light switch has the following positions: “OFF”—Turns the light off. “DOOR”—Turns the light on when either front or sliding door is opened.

2002 MY SIENNA_U (OM45407U)

127

02 SIENNA_U (L/O 0107)

Interior light

Front To turn on the front interior light, push the switch. The front interior light switch has the fol- lowing positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. Vehicles without power door lock system— “DOOR”—Turns the light on when either front door is opened. Vehicles with power door lock system— “DOOR”—Turns the light on when either front or sliding door is opened.

light,

interior

Center To turn on the center slide the switch. The center interior following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when either front or sliding door is opened.

light switch has the

Rear To turn on the rear interior light, slide the switch. The rear interior light switch has the fol- lowing positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when either sliding or back door is opened.

128

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Ignition switch light

the

INTERIOR LIGHTS CUT OFF OPERATION When the ignition switch is “OFF” and any interior lights in the vehicle stay lighting on, lights will cut off automatically after 30 minutes. You can cancel the cut off operation by: D Turning the key to the “ACC” position. D Opening or closing any of the doors. D Turning off all the “ON” lights. All the lights are turned off when all the doors are locked by the key or wireless remote control transmitter. The key must be in the “OFF” position.

ILLUMINATED ENTRY SYSTEM (with power door lock system) Front and center— With the switch in the “DOOR” position, the light comes on when either front or sliding doors are opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. However, in the following cases, the light goes out immediately: D All the doors are closed when the igni- tion key is in “ACC” or “ON” position. D All the doors are locked when the light

is still on.

D One door will be closed with the lock knob pushed forward (front door) or downward (sliding door) while the other doors are locked.

When the driver’s door is unlocked with a key, the light comes on for 15 seconds, even if the doors are not opened.

2002 MY SIENNA_U (OM45407U)

For easy access to the ignition switch, the ignition switch light comes on when any of the doors are opened. The light remains on for 15 seconds when all the doors are closed. Vehicles with power door lock system— However, in the following cases, the light goes out immediately: D All the doors are closed when the igni- tion key is in “ACC” or “ON” position. D All the doors are locked when the light

is still on.

D One door will be closed with the lock knob pushed forward (front door) or downward (sliding door) while the other doors are locked.

129

02 SIENNA_U (L/O 0107)

Luggage compartment light

the

ignition switch

LUGGAGE COMPARTMENT LIGHT CUT OFF OPERATION is “OFF” and When luggage compartment light in the vehicle stays lighting on, the light will cut off au- tomatically after 30 minutes. You can cancel the cut off operation by: D Turning the key to the “ACC” position. D Opening or closing any of the doors. D Turning off all the “ON” lights. The light is turned off when all the doors are locked by the key or wireless remote control transmitter. The key must be in the “OFF” position.

To turn the luggage compartment light on, open the back door and push the switch downwards. To turn it off, push the switch upwards or close the back door.

the

ignition switch

When the driver’s door is unlocked with a key, the light comes on for 15 seconds, even if the doors are not opened. IGNITION SWITCH LIGHT CUT OFF OPERATION When is “OFF” and ignition switch light in the vehicle stays lighting on, the light will cut off automati- cally after 30 minutes. You can cancel the cut off operation by: D Turning the key to the “ACC” position. D Opening or closing any of the doors. D Turning off all the “ON” lights. The light is turned off when all the doors are locked by the key or wireless remote control transmitter. The key must be in the “OFF” position.

130

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Windshield wipers and washer

Rear window wiper and washer

To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield the glass.

It may scratch

is dry.

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Position 3

Intermittent

Slow

Fast

interval adjuster: The

With “INT TIME” band lets you adjust the wiping time inter- val when the wiper lever is in the intermit- tent position (position 1). Twist the band upward time between sweeps, and downward to decrease it.

increase

the

to

To turn on the rear window wiper, twist the lever knob upward. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Intermittent

Normal

To squirt washer fluid on the rear window, twist the knob upward or downward as far as it will go (position 3 or 4). The knob automatically returns from these positions after you release it. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7−3.

2002 MY SIENNA_U (OM45407U)

131

02 SIENNA_U (L/O 0107)

Rear window and outside rear view mirror defoggers

NOTICE

Do not operate the rear wiper if the rear window is dry. It may scratch the glass.

With manual air conditioning controls

To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the window surfaces. An indicator light will illuminate to indicate the defogger is operating. On some models, heater panels in the outside rear view mirrors will also quickly clear the surfaces. Push the switch once again to turn the defoggers off. The system will automatically shut off af- ter the defoggers have operated about 15
minutes.

CAUTION

On some models, since the mirror surfaces can get hot, keep your hands off them when the defogger switch is on.

132

2002 MY SIENNA_U (OM45407U)

With automatic air conditioning controls

02 SIENNA_U (L/O 0107)

turn

Make sure you the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow.

If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

2002 MY SIENNA_U (OM45407U)

133

02 SIENNA_U (L/O 0107)

134

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

SECTION 1− 5

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers

136
136
137
138
138

2002 MY SIENNA_U (OM45407U)

135

02 SIENNA_U (L/O 0107)

Fuel gauge

Engine coolant temperature gauge

the

The gauge works when ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. This fuel gauge has a non−return type needle which remains at the last indicated position when the ignition switch is turned off. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

2002 MY SIENNA_U (OM45407U)

With tachometer

Without tachometer

With tachometer

Low fuel level warning light

Without tachometer

136

02 SIENNA_U (L/O 0107)

Tachometer

The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high

speed driving.

D Idling for a long period with the air conditioning on in stop−and−go traffic.

D Towing a trailer.

NOTICE

z Do not remove the thermostat

in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.

z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” in Section 4.

The tachometer indicates engine speed in thousands of rpm ( revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.

NOTICE

Do not let the indicator needle get into the red zone. This may cause severe engine damage.

2002 MY SIENNA_U (OM45407U)

137

02 SIENNA_U (L/O 0107)

Odometer and two trip meters

This meter displays the odometer and two trip meters. 1. Odometer—It shows the total distance

the vehicle has been driven.

2. Two

trip meters—Show

two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.

fuel economy and

the other

3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

to

2002 MY SIENNA_U (OM45407U)

With tachometer

Without tachometer

138

Service reminder indicators and warning buzzers

If the indicator or buzzer comes on...

Do this.

or

(a)

(b)

If parking brake is

off, stop immediately and contact Toyota dealer.

Fasten driver’s seat belt.

(indicator and buzzer)

(c)

(d)

Fasten front passenger’s seat belt.

Stop and check.

02 SIENNA_U (L/O 0107)

If the indicator or buzzer comes on...

Do this.

If the indicator or buzzer comes on...

Do this.

If the indicator or buzzer comes on...

Do this.

or

or

Low fuel level warning light

(e)

(f)

(g)

Take vehicle to Toyota dealer.

(h)

or

Fill up tank.

Stop and check.

(i)

(j)

Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer.

Close all doors.

Close the power sliding door.

(l)

(m)

(n)

Take vehicle to Toyota dealer.

Add washer fluid.

Adjust tire pressure.

(o)

Key reminder buzzer

Remove key.

(indicator and buzzer)

(k)

Take vehicle to Toyota dealer immediately.

2002 MY SIENNA_U (OM45407U)

139

02 SIENNA_U (L/O 0107)

CAUTION

(b) Driver’s Seat Belt Reminder Light

and Buzzer

If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The

light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. De- press the brake pedal firmly and bring the vehicle to an immediate stop.

D The brake system warning light re- mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely un- stable during braking.

to

reminder

remind you

light and buzzer

This buckle up the driver’s seat belt. Once the ignition key is turned to “ON”, the flashes and buzzer sounds if the driver’s seat belt is not fas- tened. Unless the driver fastens the belt, the light keeps flashing and the buzzer stops after about 4 to 8 seconds. (c) Front Passenger’s Seat Belt Re-

light

minder Light

This light reminds you to buckle up the front passenger’s seat belt. Once the ignition key is turned to “ON”, the reminder light flashes if a passenger sits in the front passenger seat and does not fastened. However, if a front passen- ger uses an additional seat cushion, the light may not flash even when the seat belt is not buckled up. If front passenger seat, depending on its weight and how it is placed on the seat, built−in sensors in the seat cushion may detect the pressure, causing the reminder light to come on.

is placed on

luggage

load

the

(a) Brake System Warning Light This light comes on in the following cases when the ignition key is in the “ON” posi- tion. D When the parking brake is applied... This light comes on for a few seconds when to the “ON” position even after the parking brake is released. D When the brake fluid level is low...

ignition key

turned

the

is

CAUTION

It is dangerous to continue driving normally when the brake fluid level is low.

Have your vehicle checked at your Toyota dealer in the following case: D The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.

D The light does not come on even if the ignition key is turned on with the park- ing brake released.

A warning light turning on briefly during operation does not indicate a problem.

140

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

(d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.

NOTICE

Do not continue driving if the engine drive belt is broken or loose.

(e) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on, or the lamp comes on while driving, first check the followings. D Empty fuel tank

If the fuel tank is empty, refuel immedi- ately.

D Loose fuel tank cap

If the fuel tank cap is loose, securely tighten it.

These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp will not go off even after the several trips, contact your Toyota dealer as soon as possible. If the fuel tank is not empty or the fuel tank cap is not loose... D There is a problem somewhere in the engine, emission control system, auto- matic transmission electrical system or warning light system itself.

inspection

Contact your Toyota dealer as soon as possible to service the vehicle. Emissions Inspection and Maintenance (I/M) programs Your vehicle may not pass a state emission the malfunction indicator lamp remains on. Contact your to check your vehicle’s Toyota dealer emission and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection. For details, see “Emissions Inspection and Maintenance (I/M) programs” in Section 6.

system

control

if

(f) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual. (g) Low Engine Oil Pressure Warning

Light

This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.

light may occasionally

low. It

2002 MY SIENNA_U (OM45407U)

141

02 SIENNA_U (L/O 0107)

the following conditions If either of occurs, indicates a malfunction this somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.

D The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem.

CAUTION

If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.

(i) Open Door Warning Light This light remains on until all the doors are completely closed. (j) Open Power Sliding Door Warning

Light and Buzzer

is not completely closed with

This light comes on if the power sliding door the ignition key in the “ON” position. If you forcibly close the power sliding door by hand when the ignition key is in the “ON” position, the open power sliding door warning light may stay on. In this case, try opening and closing the power sliding door again by hand slowly, or use one of the “DOOR L”, “PWR DOOR” switches the vehicle or “POWER DOOR”, “D−PWR DOOR” or “P− PWR DOOR” switches of the wireless re- mote control transmitter. If you shift out of “P” when the power sliding door is opened or in the process of closing with the power sliding door sys- tem on, a buzzer will sound and the open power sliding door warning light will flash. This is a warning that the sliding door is not completely closed.

“DOOR R” or inside

NOTICE

the Do not drive warning light on—even for one block. It may ruin the engine.

the vehicle with

if

few seconds. Thereafter,

(h) “ABS” Warning Light The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system and the brake assist system works properly, the light turns off after a the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system, the brake assist system, the traction control system and vehicle skid control system do not oper- ate, but the brake system still operates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.

142

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

(k) SRS Warning Light This light will come on when the igni- tion key is turned to the “ACC” or “ON” position. After about 6 seconds, the light will go off. This means the system of the airbag and front seat belt pretensioners are operating properly. The warning light system monitors the air- bag sensor assembly, front airbag sen- sors, side airbag sensor, front seat belt pretensioner assemblies, inflators, warning light, interconnecting wiring and power sources. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ACC” or “ON” position or remains on.

D The light comes on or flashes while

driving.

(l) Vehicle Skid Control System/Traction

Control System Warning Light

This light warns that there is a problem somewhere in the vehicle skid control sys- tem or traction control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing. In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the

ignition key is turned to “ON”.

D The warning light comes on while driv-

ing.

(m) Low Windshield Washer Fluid Level

Warning Light

The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” in Section 7−3.) (n) Low Tire Pressure Warning Light This light warns that the tire pressure of any one of the tires is critically reduced. The light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the low tire pressure warning system is functioning properly. If the light comes on while driving, adjust tire pressure to the specified level. (See “Tires” in Section 8.) After the tire pres- sure is adjusted, the light should go off after driving at about more than 30 km/h (19 mph) for some time. If the light still remains, have the low tire pressure warn- ing system checked at your Toyota dealer. (o) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position.

2002 MY SIENNA_U (OM45407U)

143

02 SIENNA_U (L/O 0107)

6. Vehicles with a power sliding door sys-

tem: Open the sliding door. The open power sliding door warning light should come on. Close the sliding door. The open power sliding door warning light should go off.

If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.

light

SERVICE

CHECKING REMINDER INDICATORS (except the low fuel level warning low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the doors.

and

The open door warning come on.

light should

3. Close the door.

The open door warning light should go off.

4. Turn the ignition key to “ACC”.

The SRS warning light should come on. It goes off after about 6 seconds.

5. Turn the ignition key to “ON”, but do

not start the engine. All the service reminder indicators ex- cept the open door warning light, open power sliding door warning light and SRS warning light should come on. The “ABS” warning “VSC” warning light, low tire pressure warning lights, “TRAC OFF” indicator light and slip in- dicator light go off after a few seconds.

light,

144

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

SECTION 1− 6

OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traction control system Vehicle skid control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tire pressure warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

146
147
151
153
155
156
157

2002 MY SIENNA_U (OM45407U)

145

02 SIENNA_U (L/O 0107)

Ignition switch with steering lock

You must push in the key to turn the key from “ACC” to the “LOCK” position. The selector lever must be put in the “P” posi- tion before pushing the key. Vehicles with engine immobiliser system— Once you remove the key, the engine im- mobiliser system is automatically set. (See “Engine in Section 1−2.) When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently.

immobiliser system”

NOTICE

leave the key

in the “ON” Do not position if the engine is not running. The battery will discharge and the ignition could be damaged.

2002 MY SIENNA_U (OM45407U)

“START”—Starter motor on. The key will return to the “ON” position when released. For starting tips, see Section 3. “ON”—Engine on and all accessories on. This is the normal driving position. “ACC”—Accessories such as the radio operate, but the engine is off. the “ACC” or If you “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key. “LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position. 146

the key

leave

in

02 SIENNA_U (L/O 0107)

Automatic transmission

Selector lever

Overdrive switch

With the brake pedal depressed, shift while pulling the selector lever toward you. (The ignition switch must be in “ON” or “ACC” position.)

Shift while pulling the selector lever toward you.

Shift normally.

Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” or “ACC” position and the selector lever pulled toward you). (a) Selector lever The shift position is displayed on the in- strument cluster. P: Parking, engine starting and

key removal

R: Reverse N: Neutral D: Normal driving (with overdrive on) 2: Stronger engine braking L: Maximum engine braking

2002 MY SIENNA_U (OM45407U)

147

02 SIENNA_U (L/O 0107)

Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” in Section 3. The transmission must be in “P” or “N”.

2. With your foot holding down the brake

pedal, shift the selector lever to “D”.

When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into overdrive gear even with the overdrive on.

temperature

low,

is

CAUTION

Never put your foot on the accelera- tor pedal while shifting.

2002 MY SIENNA_U (OM45407U)

3. Release the parking brake and brake the accelerator pedal

pedal. Depress slowly for smooth starting.

(d) Using engine braking To use engine braking, you can downshift the transmission as follows: D Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to third gear.

D Shift into the “2” position. The trans- mission will downshift to second gear when the vehicle speed drops down to or lower than 112 km/h (69 mph), and stronger engine braking will be en- abled.

D Shift into the “L” position. The trans- mission will downshift first gear when the vehicle speed drops down to or lower than 58 km/h (36 mph), and maximum engine braking will be en- abled.

to

Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled.