2010 Toyota RAV4 Owners Manual

Replace the electronic key battery.

Start the engine with the electronic key present.

Turn the “ENGINE START STOP” switch OFF and close the driver’s door again.

Bring the electronic key back into the vehi- cle.

■If the smart key system does not operate properly

●Locking and unlocking the doors: Use the mechanical key. (→P. 451) ●Starting the engine. (→P. 451)

■When the electronic key battery is fully depleted

→P. 380

35

1-2. Opening, closing and locking the doors

■Customization that can be configured at Toyota dealer

It is possible to deactivate the smart key system etc. (Customizable features →P. 488)

■Certification for the smart key system

For vehicles sold in the U.S.A.

FCC ID: NI4TMLF-2
FCC ID: HYQ14AAB FCC ID: HYQ13BZS FCC ID: HYQ14ABK FCC ID: HYQ13CZA NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

For vehicles sold in Canada

NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

36

1

1-2. Opening, closing and locking the doors

CAUTION

■Caution regarding interference with electronic devices

●People with implanted pacemakers or cardiac defibrillators should keep away from smart key system antennas. (→P. 28) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Then, consult your doctor to see if you should disable the entry function.

●User of any electrical medical device other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.

Ask your Toyota dealer for details for disabling the entry function.

37

1-2. Opening, closing and locking the doors Wireless remote control

The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle.

Vehicles without smart key system

and

holding:

Locks all doors Pushing Sounds alarm Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.

Vehicles with smart key system

Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Pushing Sounds alarm

holding:

and

■Operation signals

Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)

38

1

1-2. Opening, closing and locking the doors

■Panic mode

Vehicles without smart key system

When is pushed for longer than about one second, an alarm will sound for about 60 seconds and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, push any button on the wireless remote control.

Vehicles with smart key system

When is pushed for longer than about one second, an alarm will sound for about 60 seconds and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, push any button on the wireless remote control.

■Door lock buzzer

If a door is not fully closed, a buzzer sounds continuously if an attempt to lock the door is made. Fully close the door to stop the buzzer, and lock the vehicle once more.

■Key battery depletion

Vehicles without smart key system

The standard battery life is 1 to 2 years. (The battery becomes depleted even if the key is not used.) If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (→P. 380)

Vehicles with smart key system

→P. 380

39

1-2. Opening, closing and locking the doors

■If the wireless remote control does not operate

Vehicles without smart key system

Locking and unlocking the doors: Use the key. (→P. 42)

Vehicles with smart key system

●Locking and unlocking the doors: Use the mechanical key. (→P. 451) ●Starting the engine. (→P. 143)

■Security feature

If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the anti-theft system automatically locks the vehicle again.

■Conditions affecting operation

Vehicles without smart key system

The wireless remote control function may not operate normally in the follow- ing situations. ●Near a TV tower, radio station, electric power plant, airport or other facil-

ity that generates strong radio waves

●When carrying a portable radio, cellular phone or other wireless commu-

nication devices

●When multiple wireless keys are in the vicinity ●When the wireless key is in contact with, or is covered by a metallic

object

●When a wireless key (that emits radio waves) is being used nearby ●When the wireless key has been left near an electrical appliance such as

a personal computer Vehicles with smart key system

→P. 30

■Customization that can be configured at Toyota dealer

Settings (e.g. wireless remote control) can be changed. (Customizable features →P. 488)

40

1

1-2. Opening, closing and locking the doors

■Certification for wireless remote control (vehicles without smart key

system)

For vehicles sold in the U.S.A.

FCC ID: HYQ12BBY FCC ID: HYQ13BBZ FCC ID: HYQ12BDC FCC ID: HYQ13BDC NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

For vehicles sold in Canada

NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

■Certification for wireless remote control (vehicles with smart key sys-

tem) →P. 36

41

1-2. Opening, closing and locking the doors Side doors

The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (vehicles with smart key system)

→P. 26

■ Wireless remote control

→P. 38

■ Key

Vehicles without smart key system

Locks all doors Unlocks all doors Turning the key unlocks the driver's door. Turning the key again within 3 seconds unlocks the other doors.

Vehicles with smart key system The doors can also be locked and unlocked with the mechanical key. (→P. 451)

42

1-2. Opening, closing and locking the doors

■ Door lock switch

Locks all doors Unlocks all doors

■ Inside lock button

Locks the door Unlocks the door Pulling the door handle can open the front door even if the lock button is in the lock posi- tion.

43

1-2. Opening, closing and locking the doors

Locking the front doors from the outside without the wireless remote control or key

STEP 1

STEP 2

Move the inside door lock button to the lock position. Close the door.

Rear door child-protector locks

The door cannot be opened from inside the vehicle when the child- protector lock is set.

These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.

44

1-2. Opening, closing and locking the doors

■When all the doors are locked with the entry function (vehicles with

smart key system), wireless remote control or key The doors cannot be unlocked with the door lock switch. The door lock switch can be reset by unlocking all the doors with the entry function (vehicles with smart key system), wireless remote control or key.

■The doors cannot be locked when Vehicles without smart key system

The key is in the engine switch and either front door is open.

Vehicles with smart key system

The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle. Depending on the position of the electronic key, the key may not be detected correctly and the door may be locked.

■Customization that can be configured at Toyota dealer

Settings (e.g. door unlocking function) can be changed. (Customizable features →P. 488)

CAUTION

■To prevent an accident

Observe the following precautions while driving the vehicle. Failing to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock the doors. ●Ensure that all doors are properly closed. ●Do not pull the inside handle of the doors while driving.

The doors may be opened and the passengers are thrown out of the vehi- cle and it may result in serious injury or death. Be especially careful for the front doors, the doors may be opened even if the inside lock buttons are in locked position.

●Set the rear door child protector locks when children are seated in the rear

seats.

45

1-2. Opening, closing and locking the doors Back door

The back door can be opened using the back door handle. The back door can be locked and unlocked using the wireless remote control, entry function (vehicles with smart key system) or door lock switch. ■ Entry function (vehicles with smart key system)

→P. 27

■ Wireless remote control

→P. 38

■ Door lock switch

→P. 43

■Customization that can be configured at Toyota dealer

Settings (e.g. wireless remote control) can be changed. (Customizable features →P. 488)

CAUTION

■Caution while driving

●Keep the back door closed while driving.

If the back door is left open, it may hit near-by objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the back door before driving.

●Before driving the vehicle, make sure that the back door is fully closed. If the back door is not fully closed, it may open unexpectedly while driving, causing an accident.

●Never let anyone sit in the luggage compartment. In the event of sudden

braking or a collision, they are susceptible to death or serious injury.

46

1-2. Opening, closing and locking the doors

CAUTION

■Caution while parking

If the open back door hides the stop, tail or rear turn signal lights, other road users must be warned of the presence of your vehicle by a warning triangle or other device.

■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not leave children alone in the luggage compartment.

If a child is accidentally locked in the luggage compartment, they could overheat.

●Do not allow a child to open or close the back door.

Doing so may cause the back door to operate unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing back door.

■Operating the back door

Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in seri- ous injury. ●When opening or closing the back door, thoroughly check to make sure

the surrounding area is safe.

●If anyone is in the vicinity, make sure they are safe and let them know that

the back door is about to open or close.

47

1-2. Opening, closing and locking the doors

CAUTION

●Use caution when opening or closing the back door in windy weather as it

may move abruptly in strong wind.

●The back door may close if it is not opened fully. It is more difficult to open or close the back door on an incline than on a level surface, so beware of the back door unexpectedly opening or closing by itself. Make sure that the back door is fully open and secure before using the luggage compartment. ●When closing the back door, take extra care to prevent your fingers etc. from being caught.

●When closing the back door, make sure

to press it lightly on its outer surface.

●Do not attach any accessories other than genuine Toyota parts to the back door. Such additional weight on the back door may interfere with the safety opening and closing operation of the back door.

48

1-3. Adjustable components (seats, mirrors, steering wheel) Front seats

Manual seat

Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (driver’s side only)

49

1-3. Adjustable components (seats, mirrors, steering wheel)

Power seat (driver’s side only)

Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch Vertical height adjustment switch Seat lumbar support adjust- ment switch

50

1

1-3. Adjustable components (seats, mirrors, steering wheel)

Flattening front seatbacks

The front seats can be moved into a flat seat arrangement.

Manual seat

STEP 1

STEP 2

Slide the second seats as far back as possible. (→P. 54) Remove the front head restraint. (→P. 65)

STEP 3

STEP 4

Slide the front seat further for- ward than the front-most lock position.

Pull the seatback angle adjust- ment lever up to unlock and push down the seatback.

After returning the seat to its origi- nal position, be certain to replace the head restraint.

51

1-3. Adjustable components (seats, mirrors, steering wheel)

Power seat

STEP 1

STEP 2

Slide the second seats as far back as possible. (→P. 54) Remove the front head restraint. (→P. 65)

Push the seat position adjusting switch forward to slide the seat to the front-most position.

Move the seatback angle adjust- ing switch backward to flatten the seatback.

After returning the seat to its origi- nal position, be certain to replace the head restraint.

When the occupant’s lower back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward and upward to help reduce the risk of whiplash on the seat occupant.

STEP 3

STEP 4

Active head restraints

52

1-3. Adjustable components (seats, mirrors, steering wheel)

■Active head restraints

Even small forces applied to the seatback may cause the head restraint to move. Pushing up a locked head restraint forcibly may appear the head restraint inner structure. These do not indicate problems.

During rear-end collision

Inner structure

CAUTION

■Seat adjustment

●Be careful that the seat does not hit passengers or luggage. ●Do not recline the seat more than necessary when the vehicle is in motion

to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident.

●Manual seat only: After adjusting the seat, make sure that the seat is

locked in position.

53

1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats

■ Second seats

Vehicles with third seat

Seat position adjustment levers Seatback angle adjustment levers When a person sits in the sec- ond center position, align all seatbacks at the same angle.

54

1-3. Adjustable components (seats, mirrors, steering wheel)

Vehicles without third seat

Seat position adjustment levers Seatback angle adjustment levers When a person sits in the sec- ond center position, align all seatbacks at the same angle.

55

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Third seats (if equipped)

The third seats do not have a seat adjustment function.

Moving a second seats for third seats entry (vehicles with third seats)

■ Getting in the vehicle (right side only)

Pull the lever forward and fold down the seatback. The seat will slide forward.

After passengers are in, lift up the seatback and return the seat to the original position.

56

1-3. Adjustable components (seats, mirrors, steering wheel)

Folding second seats

Folding down the second seats will enlarge the luggage compart- ment. ■ Before folding the second seats

STEP 1

Stow the second center seat belt. (→P. 70)

STEP 2

STEP 3

Make sure the outside seat belt passes through the hanger when folding the second seat.

This prevents the shoulder belt from being damaged.

Stow the second seat belt buck- les.

STEP 4

STEP 5

Lower the head restraint to the lowest position. (→P. 65) Raise the armrest until it locks. (→P. 320)

57

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Folding second seats

STEP 1

Slide the second seats as far back as possible. (→P. 54)

From inside

STEP 2

Pull down the seatback angle adjustment lever and fold down the seatback.

From outside (vehicles without third seats)

STEP 2

Open the back door and pull the lock release lever to fold down the second seat.

58

1-3. Adjustable components (seats, mirrors, steering wheel)

Stowing third seats (vehicles with third seats)

■ Before stowing the third seats

STEP 1

Stow the third seat belt buckles.

STEP 2

Pass the seat belts through the seat belt hangers.

This prevents the shoulder belt from being damaged.

STEP 3

Lower the head restraint to the lowest position. (→P. 65)

STEP 4

Pull the seatback lock release strap to fold down the seatback.

Make sure it is locked securely.

59

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Stowing third seats

STEP 1

STEP 2

the seat

lock Pull and hold release strap and lift up the seat rearward and then push the seat down.

Push the seat on the front side against the floor and push the seat on rear side against the floor.

Make sure it is locked securely.

60

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Returning third seats

STEP 1

Pull the seat lock release strap, lift the seat up and move the seat forward. Lock the seat into place.

Make sure it is locked securely.

STEP 2

Pull the seatback lock release strap and raise the seatback.

If the seat does not lift up when the seat lock release strap is pulled, lock the seatback again.

61

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Seat adjustment

Observe the following precautions. Failure to do so may result in death or serious injuries. ●The seat belts provide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt.

●Be careful not to get your hands or feet pinched in the seat. ●Do not adjust the seat while the vehicle is moving as the seat may unex-

pectedly move and cause the driver to lose control of the vehicle.

●Be careful that the seat does not hit a passenger or luggage. ●Do not put objects under the seats.

Otherwise, the objects may interfere with the seat-lock mechanism or unexpectedly push up the seat position adjustment lever and the seat may suddenly move, causing the driver to lose control of the vehicle.

●Avoid reclining the seatback any more than needed. ●Adjust both seat cushions to the same position and align all seatbacks at

the same angle when a person sits in the rear center position. Otherwise, the person cannot wear the seat belt properly and this may cause death or serious injuries in a collision.

62

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When folding second seats

●Do not fold the second seatback when passengers sit or luggage is placed

on the seat.

●Do not allow passengers to ride on the folded seat or in the luggage com-

partment while driving.

●Make sure that no passengers or luggage are on the rear seats. ●Make sure the seatback is securely locked by pushing forward and rear-

ward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly.

■When stowing third seats

●Make sure that no passenger or luggage are on the seats. Then, hold the

seat and slowly move it. Otherwise, people may be injured or luggage may be damaged if the seat hits them.

●Make sure the seat is securely locked by pushing forward and rearward on the top of the seatback or by trying to pull up the edge of the bottom cush- ion. Failure to do so will prevent the seat belt from operating properly.

●Make sure the seat belts are not twisted or caught in the seatback and are

arranged in their proper position ready for use.

●Do not stow or return the seats when you are inside the vehicle in order to

prevent pinching your hands or feet in the seat. Be sure to stow and return the seats from outside the vehicle.

63

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■After adjusting a seat

●After adjusting the seat position, try sliding it forward and backward to

make sure it is locked in position.

●After adjusting the seatback, push your body adjust the seatback to make

sure it is locked in position.

●Make sure the seat belts are not twisted or caught in the seatback and are

arranged in their proper position and are ready for use.

NOTICE

■Before folding the seats

To prevent damage to the seat belt buckles, stow them before folding the seatback.

64

1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints

Head restraints are provided for all seats.

Front seats

Up Pull the head restraints up. Down Push the head restraint down while pushing the lock release button.

Lock release button

Second seats

Lock release buttons

Third seats (if equipped)

Lock release button

65

1-3. Adjustable components (seats, mirrors, steering wheel)

■Removing the head restraints Except second center seat

Pull the head restraint up while pushing the lock release button.

Second center seat

■Installing the head restraints Except second center seat

Align the head restraint with the installa- tion holes and push it down while press- ing the lock release button.

66

1-3. Adjustable components (seats, mirrors, steering wheel)

Second center seat

■Adjusting the height of the head restraints

Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.

■Adjusting the rear seat head restraints

Always raise the head restraint one level from the stowed position when using.

CAUTION

■Head restraint precautions

Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure

they are locked in position.

●Do not drive with the head restraints removed.

67

1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts

Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts

● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der.

● Position the lap belt as low

as possible over the hips.

● Adjust the position of the seatback. Sit up straight and well back in the seat. ● Do not twist the seat belt.

■ Fastening and releasing the seat belt

Fastening the belt Push the tab into the buckle until a clicking sound is heard. Releasing the belt Press the release button.

Release button

68

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Adjusting the height of the belt (front seats)

Down Up Move the height adjuster up and down as needed.

Second center seat belt

The second center seat belt is a 3-point type restraint with 2 buckles. Both seat belt buckles must be correctly located and securely latched for proper operation.

Make sure that the buckle is securely latched ready for use of the center seat belt.

Matches the tab with hook end. Matches the tab with round end.

69

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Releasing method

The second center seat belt can be completely released only when necessary such as when folding down the second seats.

STEP 1

STEP 2

Insert the key into the hole on the center seat belt buckle to release the tab (with hook end), and allow the belt to retract.

Stow the seat belt tabs in the cover located on the roof as shown.

Seat belt pretensioners (front seats)

The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision or a vehicle rollover.

The pretensioner may not acti- vate in the event of a minor frontal impact, a side impact or a rear impact.

70

1-3. Adjustable components (seats, mirrors, steering wheel)

■Emergency locking retractor (ELR)

The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.

■Automatic locking retractor (ALR)

When a passenger's shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (→P. 121)

■Pregnant women

Obtain medical advice and wear the seat belt in the proper way. (→P. 68) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a collision.

■People suffering illness

Obtain medical advice and wear the seat belt in the proper way.

71

1-3. Adjustable components (seats, mirrors, steering wheel)

■When not using the rear seat belts

Second seats

Pass the outer seat belts through the seat belt hangers and secure the seat belt plates to prevent the shoulder belts from being damaged.

Third seats

Pass the seat belts through the seat belt hangers to prevent the shoulder belts from being damaged.

■Child seat belt usage

The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle's seat belt. (→P. 117) ●When the child becomes large enough to properly wear the vehicle's seat

belt, follow the instructions on P. 68 regarding seat belt usage. ■Replacing the belt after the pretensioner has been activated

If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.

72

1-3. Adjustable components (seats, mirrors, steering wheel)

■Seat belt extender

If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.

they are not

CAUTION

Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failing to do so may cause death or severe injury. ■Wearing a seat belt

●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt

for more than one person at once, including children.

●Toyota recommends that children be seated in the rear seat and always

use a seat belt and/or an appropriate child restraint system.

●Do not recline the seat any more than necessary to achieve a proper seat- ing position. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.

●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.

■Adjustable shoulder anchor

Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (→P. 69)

73

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Seat belt pretensioners

●Do not place anything, such as a cushion, on the front passenger's seat. Doing so will disperse the passenger's weight, which prevents the sensor from detecting the passenger's weight properly. As a result, the seat belt pretensioner for the front passenger's seat may not activate in the event of a collision.

●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.

■Child restraint lock function belt precaution

Do not allow children to play with the child restraint lock function belt. If the belt becomes twisted around a child’s neck, it will not be possible to pull the belt out leading to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.

■Seat belt damage and wear

●Do not damage the seat belts by allowing the belt, plate, or buckle to be

jammed in the door.

●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belt cannot protect an occupant from death or serious injury.

●Ensure that the belt and tab are locked and the belt is not twisted.

If the seat belt does not function correctly, immediately contact your Toyota dealer.

●Replace the seat assembly, including the belts, if your vehicle has been

involved in a serious accident, even if there is no obvious damage.

●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.

74

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When using the second center seat belt

Do not use the second center seat belt with either buckle released. Fastening only one of the buckles may result in death or serious injury in case of sudden braking or a collision.

■Using a seat belt extender

●Do not wear the seat belt extender if you can fasten the seat belt without

the extender.

●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.

●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.

NOTICE

■When using a seat belt extender

When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.

75

1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel

The steering wheel can be adjusted to a comfortable position.

STEP 1

STEP 2

Hold the steering wheel and press the lever down.

Adjust to the ideal position by moving the steering wheel horizontally and vertically.

After adjustment, pull the lever up the steering wheel.

to secure

CAUTION

■Caution while driving

Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident and resulting in death or serious injury.

76

1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror

Glare from the headlights of vehicles behind can be reduced by using the following functions.

Manual anti-glare inside rear view mirror

Normal position Anti-glare position

Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.

Turns automatic mode on/off

The indicator comes on when automatic mode is turned ON. Vehicles without smart key system: The mirror will revert to the automatic mode each time the engine switch is turned to the “ON” position. Vehicles with smart key sys- tem: The mirror will revert to the automatic mode each time the “ENGINE STOP” switch is turned to IGNITION ON mode.

START

77

1-3. Adjustable components (seats, mirrors, steering wheel)

Adjusting the height of rear view mirror

Adjust the height of the rear view mirror by moving it up and down.

■To prevent sensor error (vehicles with auto anti-glare inside rear view

mirror)

To ensure that the sensors operate prop- erly, do not touch or cover them.

CAUTION

■Caution while driving

Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.

78

1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors

Vehicles without smart key system

Mirror angle can be adjusted using the switch when the engine switch is in the “ACC” or “ON” position.

Vehicles with smart key system

Mirror angle can be adjusted using the switch when the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.

STEP 1

Select a mirror to adjust.

Left Right

STEP 2

Adjust the mirror.

Up Right Down Left

79

1-3. Adjustable components (seats, mirrors, steering wheel)

Folding back the mirrors

Push backward to fold the mir- rors.

■When the mirrors are fogged up (vehicles with outside rear view mirror

defoggers) Turn on the mirror defoggers to defog the mirrors. (→P. 233)

CAUTION

■When driving the vehicle

Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded back. ●Both the driver and passenger side mirrors must be extended and properly

adjusted before driving.

■When the mirror defoggers are operating (vehicles with outside rear

view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.

80

1

1-4. Opening and closing the windows and moon roof Power windows

The power windows can be opened and closed using the following switches.

Closing One-touch closing (driver’s window only)* Opening One-touch opening (driver’s window only)*

*: Pressing

the switch

the opposite direction will stop win- dow travel partway.

in

Lock switch

Press the switch down to lock the passenger window switches. Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.

81

1-4. Opening and closing the windows and moon roof

■The power windows can be operated when

Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

■Operating the power windows after turning the engine off (front win-

dows only)

Vehicles without smart key system

The power windows can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, how- ever, be operated once either front door is opened.

Vehicles with smart key system

The power windows can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned OFF. They cannot, however, be operated once either front door is opened.

■Jam protection function (driver’s window only)

If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.

■When the battery is disconnected

The power windows must be initialized in order to ensure proper operation. (Initialize each window with the respective switches.)

STEP 1

STEP 2

Open the window fully. Fully close the window by pulling the switch up and holding it for 1 second.

82

1

1-4. Opening and closing the windows and moon roof

CAUTION

■Closing the windows

Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body

in a position where it could be caught when a window is being operated.

●Do not allow children to operate the power windows.

Closing a power window on someone can cause serious injury, and in some instances, even death.

■Jam protection function (driver’s window only)

●Never try jamming any part of your body to activate the jam protection

function intentionally.

●The jam protection function may not work if something gets caught just

before the window fully closes.

83

1-4. Opening and closing the windows and moon roof Moon roof∗

Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing

Open The moon roof stops slightly before the fully opened posi- tion. Press the switch again to fully open. Close Press either side of the switch to stop the moon roof partway.

Tilt up Tilt down Press either side of the switch to stop the moon roof partway.

■ Tilting up and down

■The moon roof can be operated when

Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

84

∗: If equipped

1-4. Opening and closing the windows and moon roof

■Operating the moon roof after turning the engine off

Vehicles without smart key system

The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, how- ever, be operated once either front door is opened.

Vehicles with smart key system

The moon roof can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned OFF. They cannot, however, be operated once either front door is opened.

■Jam protection function

If an object is detected between the moon roof and the frame while closing or tilting down, travel is stopped and the moon roof opens slightly.

■If the moon roof cannot be closed

If the moon roof cannot be closed automatically, such as when the jam pro- tection function activates accidentally due to a malfunction, press and hold the “TILT UP” side of the switch until the moon roof slide closed completely.

■To reduce wind noise

Drive with the moon roof opened to a position that is slightly before the fully open position as driving with the moon roof opened fully will cause wind noise.

■Sunshade

The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.

■Opening the moon roof by small degrees

Quickly press and release the switch. ■When the battery is disconnected

The moon roof must be initialized in order to ensure proper operation. Press and hold the “TILT UP” side of the switch until the moon roof tilts up completely.

85

1-4. Opening and closing the windows and moon roof

■When the moon roof does not close normally

Perform the following procedure: ●If the moon roof closes but then re-opens slightly

STEP 1

STEP 2

STEP 3

Stop the vehicle. Press and hold the “TILT UP” switch.*1 The moon roof will close, reopen and pause for approximately 10 seconds.*2 Then it will close again, tilt up and pause for approxi- mately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

●If the moon roof tilts down but then tilts back up

STEP 1

STEP 2

STEP 3

STEP 4

Stop the vehicle. Press and hold the “TILT UP” switch*1 until the moon roof moves into the tilt up position and stops. Release the “TILT UP” switch once and then press and hold the “TILT UP” switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up position.*2 Then it will adjust slightly and pause for approximately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch. *1:If the switch is released at the incorrect time, the procedure will

have to be performed again from the beginning.

*2:If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the “TILT UP” switch, and the moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.

86

1

1-4. Opening and closing the windows and moon roof

CAUTION

■Opening the moon roof

Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-

cle while it is moving.

●Do not sit on top of the moon roof.

■Closing the moon roof

Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where it could be caught when the moon roof is being operated.

●Do not allow children to operate the moon roof.

Closing the moon roof on someone can cause death or serious injury.

■Jam protection function

●Never try jamming any part of your body to activate the jam protection

function intentionally.

●The jam protection function may not work if something gets caught just

before the moon roof fully closes.

87

1-5. Refueling Opening the fuel tank cap

Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle

Vehicles without smart key system

Turn the engine switch to the “LOCK” position and ensure that all the doors and windows are closed.

Vehicles with smart key system

Turn the “ENGINE START STOP” switch OFF and ensure that all the doors and windows are closed.

■ Opening the fuel tank cap

STEP 1

Pull up the fuel filler door opener.

STEP 2

Turn the fuel tank cap slowly to open.

88

1-5. Refueling

STEP 3

Hang the fuel tank cap on the back of the fuel filler door.

Closing the fuel tank cap

When replacing the fuel tank cap, turn it until a clicking sound is heard.

After releasing your hand, the cap will turn slightly to the opposite direction.

■Fuel types

Use unleaded gasoline. (Octane rating 87 [Research Octane Number 91] or higher)

■Fuel tank capacity

Approximately 15.9 gal. (60 L, 13.2 Imp. gal.)

89

1-5. Refueling

CAUTION

■Refueling the vehicle

Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●Touch the vehicle or some other metal surface to discharge any static

electricity. Sparks resulting from discharging static electricity may cause the fuel vapors to ignite.

●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out of the filler neck and cause injury.

●Do not allow anyone that has not discharged static electricity from their

bodies to come close to an open fuel tank.

●Do not inhale vaporized fuel.

Fuel contains substances that are harmful if inhaled.

●Do not smoke while refueling the vehicle.

Doing so may cause the fuel to ignite and cause a fire.

●Do not return to the vehicle or touch any person or object that is statically

charged. This may cause static electricity to build up, resulting in a possible ignition hazard.

■When replacing the fuel cap

Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.

90

1-5. Refueling

NOTICE

■Refueling

Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.

91