2010 Toyota RAV4 Owners Manual

2-4. Using other driving systems Downhill assist control system∗

With the downhill assist control system, the vehicle is able to descend a steep hill while maintaining a constant low speed of about 3 mph (5 km/h) without brake pedal operation. ■ Activating the downhill assist control system

Press the “DAC” switch.

The downhill assist control sys- tem indicator will come on to indicate that the downhill assist control system is activated. Pressing the switch again turns the system off.

While the downhill assist control system is operating

The slip indicator will flash to indicate that the downhill assist control system is operating, and the stop lights and high mounted stoplight will turn on.

∗: If equipped 189

2-4. Using other driving systems

■Conditions in which the downhill assist control system does not oper-

ate or will stop operating ●In the following situations, the downhill assist control system indicator flashes and the downhill assist control system does not operate or will stop operating: • The shift lever is not in L or R. • The vehicle speed is higher than 15 mph (25 km/h).

●If the accelerate or brake pedal is depressed, the downhill assist control system will stop operating with the downhill assist control system indica- tor stayed on.

■If the “DAC” switch is turned off while the downhill assist control sys-

tem is operating The downhill assist control system gradually ceases operation. The downhill assist control system indicator will flash during the canceling operation, and then go off when the system is fully off.

■Downhill assist control system operation sound

●A sound may be heard from the engine compartment while the downhill assist control system is operating. This sound does not indicate a mal- function.

●If the accelerator or brake pedal is depressed while the downhill assist control system is operating, a sound caused by the release of system operation may be heard, or you may feel the brake pedal push-back. This does not indicate a malfunction.

■When the downhill assist control system operates continuously

The brake actuator may overheat. In that case, the downhill assist control system will stop operating, a buzzer will sound and the downhill assist con- trol system indicator will start flashing. Refrain from using the system until the downhill assist control system indicator stays on. (There is no problem with continuing driving normally.) ■If the slip indicator comes on

It may indicate a malfunction in the system. Contact your Toyota dealer.

190

2

2-4. Using other driving systems

CAUTION

■Conditions which may affect the downhill assist control system opera-

tion ●Do not rely too heavily on the downhill assist control system. On extremely steep inclines, icy surfaces or muddy roads, the vehicle may slip and the system may not be able to maintain the constant low vehicle speed of about 3 mph (5 km/h), leading to an accident causing death or serious injury.

●Do not shift the shift lever to R while driving forward, or to D while driving backward. Doing so may cause the wheels to lock up, leading to an acci- dent causing death or serious injury. In addition, excessive stress will be applied to the automatic transmission, possibly resulting in damage.

191

2-4. Using other driving systems Four-wheel drive lock switch (4WD models)

Four-wheel drive lock mode can be used when a large amount of drive power needs to be applied to all the wheels, such as when the vehicle gets stuck in mud and you need to free it.

Press the switch.

The torque of the engine is dis- tributed to the rear wheels to the maximum extent possible in accordance with driving con- ditions. Pressing the switch again can- cels lock mode and returns the active torque control 4WD system to normal mode. (→P. 180)

four-wheel drive

■Four-wheel drive lock mode can be operated when

Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

■Four-wheel drive lock mode

●Four-wheel drive lock mode is canceled when the brakes are applied to

ensure the ABS and Enhanced VSC systems operate effectively.

●Four-wheel drive lock mode is canceled when the vehicle speed exceeds

25 mph (40 km/h).

192

2

2-5. Driving information Utility vehicle precautions

This vehicle belongs to the utility vehicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity to make it capable of performing in a wide variety of off-road applications.

Off-road vehicle feature

● Specific design characteristics give it a higher center of gravity than ordinary passenger cars. This vehicle design feature causes this type of vehicle to be more likely to rollover. And, utility vehicles have a significantly higher rollover rate than other types of vehi- cles.

● An advantage of the higher ground clearance is a better view of the

road allowing you to anticipate problems.

● It is not designed for cornering at the same speeds as ordinary passenger cars any more than low-slung sports cars designed to perform satisfactorily under off-road conditions. Therefore, sharp turns at excessive speeds may cause rollover.

193

2-5. Driving information

CAUTION

■Off-road vehicle precautions

Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ●In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving.

●Avoid sharp turns or abrupt maneuvers, if at all possible.

Failure to operate this vehicle correctly may result in loss of control or vehicle rollover causing death or serious injury.

●Loading cargo on the roof luggage carrier will make the center of the vehi- cle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly.

●Always slow down in gusty crosswinds. Because of its profile and higher center of gravity, your vehicle is more sensitive to side winds than an ordi- nary passenger car. Slowing down will allow you to have better control.

●Do not drive horizontally across steep slopes. Driving straight up or straight down is preferred. Your vehicle (or any similar off-road vehicle) can tip over sideways much more easily than forward or backward.

194

2-5. Driving information

Off-road driving

When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit-

ted to travel.

● Respect private property. Get owner’s permission before entering

private property.

● Do not enter areas that are closed. Honor gates, barriers and signs

that restrict travel.

● Stay on established roads. When conditions are wet, driving tech- niques should be changed or travel delayed to prevent damage to roads.

■Additional information for off-road driving

For owners in U.S. mainland, Hawaii and Puerto Rico:

To obtain additional information pertaining to driving your vehicle off-road, consult the following organizations. ●State and Local Parks and Recreation Departments ●State Motor Vehicle Bureau ●Recreational Vehicle Clubs ●U.S. Forest Service and Bureau of Land Management

195

2-5. Driving information

CAUTION

■Off-road driving precautions

Always observe the following precautions to minimize the risk of death or serious personal injury or damage to your vehicle: ●Drive carefully when off the road. Do not take unnecessary risks by driving

in dangerous places.

●Do not grip the steering wheel spokes when driving off-road. A bad bump could jerk the wheel and injure your hands. Keep both hands and espe- cially your thumbs on the outside of the rim.

●Always check your brakes for effectiveness immediately after driving in

sand, mud, water or snow.

●After driving through tall grass, mud, rock, sand, water, etc., check that there is no grass, bush, paper, rags, stone, sand, etc. adhering or trapped on the underbody. Clear off any such matter from the underbody. If the vehicle is used with these materials trapped or adhering to the underbody, a breakdown or fire could occur.

●When driving off-road or in rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension and chassis.

NOTICE

■To prevent the water damage

Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ●Water entering the engine air intake will cause severe engine damage. ●Water entering the automatic transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ulti- mately damage.

●Water can wash the grease from wheel bearings, causing rusting and pre- mature failure, and may also enter the differentials, transmission and transfer case, reducing the gear oil’s lubricating qualities.

196

2-5. Driving information

NOTICE

■When you drive through water

If driving through water, such as when crossing shallow streams, first check the depth of the water and the bottom of the stream for firmness. Drive slowly and avoid deep water.

■Inspection after off-road driving

●Sand and mud that has accumulated around brake discs may affect brak-

ing efficiency and may damage brake system components.

●Always perform a maintenance inspection after each day of off-road driv- ing that has taken you through rough terrain, sand, mud, or water. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

197

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the luggage compartment whenever

possible. Be sure all items are secured in place.

● Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

● For better fuel economy, do not carry unnecessary weight. ■ Roof luggage carrier (if equipped)

Roof rails Cross rails

Adjusting the cross rail positions

STEP 1

Turn the knobs counterclockwise to release the cross rails.

198

STEP 2

2-5. Driving information

Slide the cross rails to the appro- priate position for loading lug- gage and the knobs clockwise to tighten the cross rails securely.

turn

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit⎯ (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle's placard.

(2)Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4)The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 - 750 (5 × 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

199

2-5. Driving information

(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, the available amount of cargo and luggage load capacity will be as follows: Without third seat Total load capacity: 825 lb. (370 kg) 825 lb. - 366 lb. = 459 lb. (370 kg - 166 kg = 204 kg) With third seat Total load capacity: 1155 lb. (520 kg) 1155 lb. - 366 lb. = 789 lb. (520 kg - 166 kg = 354 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

Without third seat 459 lb. - 388 lb. = 71 lb. (204 kg - 176 kg = 28 kg) With third seat 789 lb. - 388 lb. = 401 lb. (354 kg - 176 kg = 178 kg)

200

2-5. Driving information

As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

CAUTION

■Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment. ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●Do not place cargo or luggage in or on the following locations as the item may get under the brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Luggage cover • Instrument panel • Dashboard • Auxiliary box or tray that has no lid

●Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.

●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer serious bodily injury, in the event of sudden braking, sudden swerving or an accident.

201

2-5. Driving information

CAUTION

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant's weight and the cargo load is less

than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.

■Roof luggage carrier precautions

When you load cargo on the roof luggage carrier, observe the following: ●Place the cargo so that its weight is distributed evenly between the

front and rear axles.

●If loading long or wide cargo, never exceed the vehicle overall length

or width. (→P. 462)

●Before driving, make sure the cargo is securely fastened on the roof

luggage carrier.

●Loading cargo on the roof luggage carrier will make the center of the vehicle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly and result in death or serious injury.

●If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then during the trip to make sure the cargo remains in its place.

●Do not exceed 102.6 lb. (46.2 kg) cargo weight on the roof luggage

carrier.

■Cross rail adjustment

Make sure the cross rails are locked securely by pushing forward and rearward them. Failure to do so may cause an unexpected accident or severe injury in the event of emergency braking or a collision.

202

2-5. Driving information

NOTICE

■When loading luggage (vehicles with moon roof)

Be careful not to scratch the surface of the moon roof.

203

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: Without third seat 825 lb. (370 kg)

With third seat

1155 lb. (520 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: Without third seat

5 occupants (Front 2, Rear 3)

With third seat

7 occupants (Front 2, Rear 5)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

■ Towing capacity

2.5 L 4-cylinder (2AR-FE) engine: 1500 lb. (680 kg) 3.5 L V6 (2GR-FE) engine: Without towing package 2000 lb. (905 kg)

With towing package

3500 lb. (1585 kg)

Towing capacity means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 372)

204

2-5. Driving information

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

205

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle

Observe the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing.

● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

206

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to P without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.

Selecting tire chains

Use the correct tire chain size when mounting the snow chains. Chain size is regulated for each tire size.

Side chain 0.12 in. (3 mm) in diameter 0.39 in. (10 mm) in width 1.18 in. (30 mm) in length Cross chain 0.16 in. (4 mm) in diameter 0.55 in. (14 mm) in width 0.98 in. (25 mm) in length

Regulations on the use of snow chains

● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

● Install the chains on the front tires. ● Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

207

2-5. Driving information

■Tire chain installation

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires. ●Install tire chains following the instructions provided in the accompanying

manual.

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the specified size. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Snow tires should be installed on all wheels. ●Do not mix tires of different makes, models, tread patterns or treadwear.

■Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

208

2-5. Driving information

NOTICE

Vehicles with a tire pressure warning system: ■Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

209

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger-carrying vehicle. Towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. ■ Weight limits

Confirm that the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.

■ Gross vehicle weight

The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum weight of the unloaded vehicle, driver, passengers, luggage, hitch and trailer tongue load. Also included is the weight of any special equipment installed on your vehicle.

■ Gross axle weight

The load on either the front or rear axle resulting from distribu- tion of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

Certification label

210

2

2-5. Driving information

■ Trailer tongue load

The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the total trailer weight, not exceeding the maximum load of the following. (Tongue load / Total trailer weight x 100 = 9 to 11%)

2.5 L 4-cylinder (2AR-FE) engine: 150 lb. (68 kg) 3.5 L V6 (2GR-FE) engine

Without towing package: 200 lb. (90 kg) With towing package: 350 lb. (158 kg) The total trailer weight and tongue load can be measured with platform scales found at highway weighing stations, building supply companies, trucking companies, junk yards, etc.

Total trailer weight Tongue load

Towing a trailer

Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc.

211

2-5. Driving information

Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maxi- mum weight rating specified for the trailer hitch.

■Before towing

●Ensure that your vehicle’s tires are properly inflated. (→P. 472) ●Trailer tires should be inflated according to the trailer manufacturer's rec-

ommendation.

●All trailer lights must work in order to be legal. ●Confirm all lights work each time you connect them. ●Check that your vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

●Make sure the trailer cargo is securely loaded. ●Check that your rear view mirrors conform to any federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes. ■Break-in schedule

Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bear- ings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner's Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

212

2-5. Driving information

CAUTION

■To avoid accident or injury

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

●Never load more weight in the back than in the front of the trailer. About 60% of the load should be in the front half of the trailer, and the remaining 40% in the rear.

●Do not use cruise control when you are towing.

■Hitches

●Use only a hitch that conforms to the total trailer weight requirement. ●Follow the directions supplied by the hitch manufacturer. ●Lubricate the hitch ball with a light coat of grease. ●Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

■When towing a trailer

●If the gross trailer weight exceeds 600 lb. (272 kg), trailer brakes are

required.

●Never tap into your vehicle's hydraulic system, as this will lower the vehi-

cle's braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

213

2-5. Driving information

NOTICE

■When installing a trailer hitch

●Use only the position recommended by your Toyota dealer. Do not install

the trailer hitch on the bumper; this may cause body damage.

●Do not use axle-mounted hitches, as they can cause damage to the axle

housing, wheel bearings, wheels or tires.

■Brakes

Toyota recommends trailers with brakes that conform to all applicable fed- eral and state/provincial regulations.

■Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

■Do not directly splice trailer lights

Directly splicing trailer lights may damage your vehicle's electrical system and cause a malfunction.

Trailer towing tips

Your vehicle will handle differently when towing a trailer. The 3 main causes of vehicle-trailer accidents are driver error, excessive speed and improper trailer loading. Keep the following in mind when towing. ● Before starting out, check the trailer lights and the vehicle-trailer

connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle.

214

2-5. Driving information

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in jackknifing and

loss of control. This is especially true on wet or slippery surfaces.

● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak-

ing turns.

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a larger than normal turning radius.

● Crosswinds and rough roads will adversely affect handling of your vehicle and trailer, causing sway. Periodically check the rear to prepare for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying occurs, firmly grip the steering wheel, reduce speed immediately but gradually, and steer straight ahead. Never increase speed. If you make no extreme correction with the steering or brakes, your vehicle and trailer will stabilize.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● In order to maintain efficient engine braking and electrical charging

performance, do not use overdrive.

215

2-5. Driving information

● Due to the added load of the trailer, your vehicle's engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 456)

● Always place wheel blocks under both the vehicle and the trailer wheels when parking. Apply the parking brake firmly, and put the transmission in P. Avoid parking on a slope, but if unavoidable, do so only after performing the following:

STEP 3

STEP 2

STEP 1

Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle and trailer wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into P and turn off the engine. ● When restarting after parking on a slope:

STEP 4

STEP 5

STEP 1

STEP 2

STEP 3

STEP 4

With the transmission in P, start the engine. Be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake and brake pedal, and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

216

2-5. Driving information

CAUTION

■To avoid an accident

●Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever is lower. As instability (swaying) of the towing vehicle-trailer combination increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.

●Slow down and downshift before descending steep or long downhill

grades. Do not make sudden downshifts.

●Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

217

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with 4 wheels on the ground.

CTN25AN019

■To prevent causing serious damage to the transmission and active

torque control 4WD system (4WD models)

2WD models: Never tow this vehicle from the rear with the front wheels on the ground. This may cause serious damage to the transmission.

4WD models: Never tow this vehicle with any of the wheels on the ground. This may cause serious damage to the trans- mission and active torque control 4WD system.

CTN25AN020

CTN25AN021

218

3-1. Using the air conditioning system and defogger Manual air conditioning system∗

Air outlet selection dial

Temperature control dial

Outside air or recirculated air mode

Air conditioning on/off switch

Fan speed control dial

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

is not pressed, the system will blow ambient temperature air or

If heated air.

■ Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease). Set the dial to “0” to turn the fan off.

220

∗: If equipped

3-1. Using the air conditioning system and defogger

■ Changing the air outlets

Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can be also selected for more detailed adjustment.

Air flows to the upper body.

Air flows to the upper body and feet.

: Vehicles with third seats

Air flows to the feet.

: Vehicles with third seats

221

3-1. Using the air conditioning system and defogger

: Vehicles with third seats

Air flows to the feet and the windshield defogger operates.

The air intake is automatically switched to outside air mode. It is not possible to return to recircu- lated air mode when the dial is set at this position. Pressing to turn the air conditioning on clears the wind- shield and side windows faster.

Air flows to the windshield and side windows.

The air intake is automatically switched to outside air mode. It is not possible to return to recircu- lated air mode when the dial is set at this position. Pressing to turn the air conditioning on clears the wind- shield and side windows faster.

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (indicator off) and recircu-

lated air mode (indicator on) each time

is pressed.

222

3-1. Using the air conditioning system and defogger

Adjusting the position of the air outlets

Front outlets (center)

Direct air flow to the left or right, up or down.

Front outlets (right and left sides)

Direct air flow to the left or right, up or down.

Opening and closing the side outlets

Open the vent. Close the vent.

223

3-1. Using the air conditioning system and defogger

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

■Window defogger feature

Recirculated air mode may automatically be switched to outside air mode in situations where the windows need to be defogged.

■When outside air temperature approaches 32°F (0°C) The air conditioning system may not operate even when

■When the indicator light on

flashes

is pressed.

Press and turn off the air conditioning system before turning it on once more. There may be a problem in the air conditioning system if the indicator light keeps flashing. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the position of the temperature setting.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

CAUTION

■To prevent the windshield from fogging up

during cool air operation in Do not set the air outlet selection dial to extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

224

3-1. Using the air conditioning system and defogger

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

225

3-1. Using the air conditioning system and defogger Automatic air conditioning system∗

Airflow and outlets are automatically adjusted according to the tem- perature setting.

Driver's side temperature control

Changes the air outlets used

Outside air or recirculated air mode

Air flow display

Air conditioning on/off switch

Automatic mode Off Windshield defogger

Passenger’s side temperature control

Fan speed

Micro dust and pollen filter

Using the automatic mode

STEP 1

Press The air conditioning system begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting.

STEP 2

Press “∧” on

to increase the temperature and “∨” to

decrease the temperature. Air outlets and fan speed for the driver and passenger seats may be set separately depending on the temperature setting.

∗: If equipped

226

3-1. Using the air conditioning system and defogger

Adjusting the settings

■ Adjusting the temperature setting

Press “∧” on

to increase the temperature and “∨” to

decrease the temperature. The air conditioning system switches between individual and simulta- neous modes each time

is pressed.

Simultaneous mode (the indicator on

is off): Only

(driver’s

side) can be used to adjust the temperature for all seats.

Individual mode (the indicator on is on): The temperature for the driver and passenger seats can be adjusted separately. Operating the passenger's side temperature control starts individual mode.

■ Adjusting the fan speed

Press “∧” (increase) or “∨” (decrease) on

The fan speed is shown on the display. (7 levels) Press

to turn the fan off.

227

3-1. Using the air conditioning system and defogger

■ Changing the air outlets

Press the desired button,

or

The air flow shown on the display indicates the following.

Air flows to the upper body.

Air flows to the upper body and feet.

: Vehicles with third seats

Air flows to the feet.

: Vehicles with third seats

228

3-1. Using the air conditioning system and defogger

Air flows to the feet and the windshield defogger operates.

: Vehicles with third seats

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (indicator off) and recircu-

lated air mode (indicator on) each time

is pressed.

Defogging the windshield

Press

Air flows to the windshield and side windows. The air conditioning system oper- ates automatically. Recirculated air mode will auto- matically switched to outside air mode. It is not possible to return to recirculated air mode when the switch is on.

229

3-1. Using the air conditioning system and defogger

Micro dust and pollen filter

Press

Outside air mode will be switched to recirculated air mode. Pollen is removed from the air and the air flows to the upper part of the body. Usually the system will turn off automatically after approximately 3 minutes. To stop

the operation, press

again.

Adjusting the position of the air outlets

Front outlets (center)

Direct air flow to the left or right, up or down.

230

3-1. Using the air conditioning system and defogger

Front outlets (right and left sides)

Direct air flow to the left or right, up or down.

Opening and closing the side outlets

Open the vent. Close the vent.

■Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. In addition, the following may occur.

●Immediately after

is pressed, the fan may stop for a while until

warm or cool air is ready to flow.

●Cool air may flow to the area around the upper body when the heater is

on.

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

231

3-1. Using the air conditioning system and defogger

■Switching between outside air and recirculated air modes

Recirculated air mode or outside air mode may be automatically switched to in accordance with the temperature setting and the inside temperature.

■Window defogger feature

Recirculated air mode may automatically switch to outside air mode in situa- tions where the windows need to be defogged.

■When outside temperature approaches 32°F (0°C)

The air conditioning system may not operate even when

is pressed.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the position of the temperature setting.

■Micro dust and pollen filter

●In order to prevent the windows from fogging up when the outside air is

cold, the following may occur. • Outside air mode is not switched to recirculated air mode. • The air conditioning system operates automatically. • The operation is canceled after 1 minute.

●In rainy weather, the windows may fog up. Press

■When the indicator light on

flashes

and turn off the air conditioning system before turning it on once Press more. There may be a problem in the air conditioning system if the indicator light keep flashing. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

• It is recommended that the air conditioning system be set to outside air

mode prior to turning the vehicle off.

• The start timing of the blower may be delayed for a short period of time immediately after the air conditioning system is started in automatic mode.

232

3-1. Using the air conditioning system and defogger

CAUTION

■To prevent the windshield from fogging up

Do not use

during cool air operation in extremely humid weather. The

difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

233

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers

The rear window defogger is used to defog the rear window. The out- side rear view mirror defoggers* are used to remove frost, dew or raindrops from the outside rear view mirrors.

Vehicles with manual air conditioning system

On/off

The defoggers will automati- cally turn off after approxi- mately 15 minutes.

Vehicles with automatic air conditioning system

On/off

The defoggers will automati- cally turn off after approxi- mately 15 minutes.

*: Vehicles with outside rear view mirror defoggers

234

3-1. Using the air conditioning system and defogger

■The defogger can be operated when

Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

■Outside rear view mirror defoggers (vehicles with outside rear view

mirror defoggers) Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

CAUTION

■Outside rear view mirror defoggers (vehicles with outside rear view

mirror defoggers) The surfaces of the outside rear view mirrors become hot. Do not touch them to prevent from burning yourself.

235

3-1. Using the air conditioning system and defogger Windshield wiper de-icer∗

This feature is used to prevent ice from building up on the wind- shield and wiper blades.

On/off

The de-icer will automatically turn off after approximately 15 minutes.

■The de-icer can be operated when Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

CAUTION

■When the windshield wiper de-icer is on

Do not touch the glass at the lower part of the windshield or to the side of the front pillars as the surfaces can become very hot and burn you.

236

∗: If equipped

3-2. Using the audio system Audio system types

With navigation system

Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”.

Without navigation system (type A)

CD player with changer controller and AM/FM radio

Without navigation system (type B)

CD player with changer and AM/FM radio

236

3-2. Using the audio system

Without navigation system (type C)

CD player with changer and AM/FM radio

Title

Using the radio Using the CD player Playing back MP3 and WMA discs Optimal use of the audio system Using the AUX adapter Using the steering wheel audio switches

Page P. 239
P. 245
P. 252
P. 259
P. 262
P. 263

■Using cellular phones

Interference may be heard through the audio system's speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

237

3-2. Using the audio system

CAUTION

■For vehicles sold in U.S.A. and Canada (for U.S.A. and Canada)

●Part 15 of the FCC Rules

FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

●Laser products

• Do not take this unit apart or attempt to make any changes yourself.

This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

NOTICE

■To prevent battery discharge

Do not leave the audio system on longer than necessary when the engine is off.

■To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

238

3-2. Using the audio system Using the radio

Power Volume

Station selector

Adjusting the frequency (AM, FM mode) or channel (SAT mode)

Seeking the frequency

Changing the channel

Displaying radio text messages

AM·SAT/FM mode buttons Scanning for receivable stations

Setting station presets (excluding XM® Satellite Radio)

STEP 1

Search for desired stations by turning

or pressing “∧”

or “∨” on

STEP 2

Press and hold the button (from to be set to until you hear a beep.

to

) the station is

239

3-2. Using the audio system

Scanning radio stations (excluding XM® Satellite Radio)

■ Scanning the preset radio stations

STEP 1

STEP 2

until you hear a beep.

Press and hold Preset stations will be played for 5 seconds each. When the desired station is reached, press again.

■ Scanning all radio stations within range

once

STEP 1

STEP 2

Press All stations with reception will be played for 5 seconds each. When the desired station is reached, press again.

once

XM® Satellite Radio (if equipped) ■ Receiving XM® Satellite Radio

STEP 1

Press The display changes as follows each time pressed. AM → SAT1 → SAT2 → SAT3

is

STEP 2

Turn

to select the desired channel in the all categories,

or press “∧” or “∨” on

to select the desired channel in

the current category.

■ Setting XM® Satellite Radio channel presets

Select the desired channel. Press and hold the button (from to ) the channel is to be set to until you hear a beep.

240

3-2. Using the audio system

■ Changing the channel category

Press “∧” or “∨” on

■ Scanning XM® Satellite Radio channels

● Scanning channels in the current category

STEP 1

STEP 2

Press When the desired channel is reached, press again.

● Scanning preset channels

STEP 1

STEP 2

until you hear a beep. Press and hold When the desired channel is reached, press again.

■ Displaying text information

Press The display will show up to 10 characters. The display changes as follows each time ● Channel name ● Title (song/program title) ● Name (artist name/feature) ● Channel number

is pressed.

241

3-2. Using the audio system

■When the battery is disconnected

Station presets are erased.

■Reception sensitivity

●Cargo loaded on the roof luggage carrier, especially metal objects, may

adversely affect the reception of XM® Satellite Radio.

●Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc.

●The radio antenna is mounted on the roof. The antenna can be removed

from the base by turning it.

■XM® Satellite Radio (if equipped)

An XM® Satellite Radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 con- tiguous states and 10 Canadian provinces. ●XM® subscriptions

For detailed information about XM® Satellite Radio or to subscribe: U.S.A. ⎯ Visit on the web at www.xmradio.com or call 1-800-967-2346. Canada ⎯ Visit on the web at www.xmradio.ca or call 1-877-438-9677.

●Radio ID

You will need the radio ID when activating XM® service or reporting a

problem. Select “CH000” using

, and the receiver's 8-character ID

number will appear.

●Satellite tuner

The tuner supports only Audio Services (Music and Talk) and the accom- panying Text Information of XM® Satellite Radio.

242

3-2. Using the audio system

■If the satellite radio does not operate normally (if equipped)

If a problem occurs with the XM® tuner, a message will appear on the dis- play. Refer to the table below to identify the problem, and take the suggested corrective action.

“ANTENNA”

“UPDATING”

“NO SIGNAL”

“LOADING”

“OFF AIR”

“-----”