453
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■ Inspection and adjustment procedure
Tire valve Tire pressure gauge
ITO43P117
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the gauge gradations. If the tire inflation pressure is not at the recommended level, adjust the pressure. If you add too much air, press the center of the valve to deflate. After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage. Put the tire valve cap back on.
454
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■Tire inflation pressure check interval
You should check tire inflation pressure every two weeks, or at least once a month. Do not forget to check the spare.
■Effects of incorrect tire inflation pressure
Driving with incorrect tire inflation pressure may result in the following: ●Reduced fuel efficiency ●Reduced driving comfort and tire life ●Reduced safety ●Damage to the drive train If a tire needs frequent inflating, have it checked by your Toyota dealer.
■Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following: ●Check only when the tires are cold.
If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
●Always use a tire pressure gauge.
The appearance of the tire can be misleading. In addition, tire infla- tion pressure that is even just a few pounds off can affect ride quality and handling.
●Do not reduce tire inflation pressure after driving. It is normal for tire
inflation pressure to be higher after driving. ●Never exceed the vehicle capacity weight.
Passengers and luggage weight should be placed so that the vehicle is balanced.
455
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
CAUTION
■Proper inflation is critical to save tire performance
Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury: ●Excessive wear ●Uneven wear ●Poor handling ●Possibility of blowouts resulting from overheated tires ●Poor sealing of the tire bead ●Wheel deformation and/or tire separation ●A greater possibility of tire damage from road hazards
NOTICE
■When inspecting and adjusting tire inflation pressure
Be sure to put the tire valve caps back on. Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps are lost, replace them as soon as possible.
456
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance Wheels
If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause a loss of handling control. ■ Wheel selection
When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width and inset*. Replacement wheels are available at your Toyota dealer. *: Conventionally referred to as “offset”. Toyota does not recommend using the following: ● Wheels of different sizes or types ● Used wheels ● Bent wheels that have been straightened
■ Aluminum wheel precautions
● Use only Toyota wheel nuts and wrenches designed for use
with your aluminum wheels.
● When rotating, repairing or changing your tires, check that the
wheel nuts are still tight after driving 1000 miles (1600 km).
● Be careful not to damage the aluminum wheels when using
tire chains.
● Use only Toyota genuine balance weights or equivalent and a
plastic or rubber hammer when balancing your wheels.
457
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■When replacing wheels
The wheels of your vehicle are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advance warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, tire pressure warning valves and trans- mitters must be installed. (P. 444)
CAUTION
■When replacing wheels
●Do not use wheels that are a different size from those recommended in
the Owner’s Manual, as this may result in a loss of handling control.
●Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or seri- ous injury.
■When installing the wheel nuts
facing
tapered ends
●Be sure to install the wheel nuts with the inward. Installing the nuts with the tapered ends facing outward can cause the wheel to break and eventually cause the wheel to come off while driving, which could lead to an accident resulting in death or serious injury.
Tapered portion
ITI41P007
●Never use oil or grease on the wheel bolts or wheel nuts.
Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing an accident and resulting in death or serious injury. Remove any oil or grease from the wheel bolts or wheel nuts.
458
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
CAUTION
■Use of defective wheels prohibited
Do not use cracked or deformed wheels. Doing so could cause the tire to leak air during driving, possibly causing an accident.
NOTICE
■Replacing tire pressure warning valves and transmitters
●Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
●Ensure that only genuine Toyota wheels are used on your vehicle.
Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.
459
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance Electronic key battery
Replace the battery with a new one if it is depleted. ■ You will need the following items:
● Flathead screwdriver
● Lithium battery CR1632
■ Replacing the battery
STEP 1
Take out the mechanical key.
STEP 2
STEP 3
Remove the cover.
To prevent damage, cover the tip of the screwdriver with a rag.
Remove the depleted battery. Insert a new battery with the “+” terminal facing up.
STEP 4
When installing, reverse the steps listed.
ITO43P194
460
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■Use a CR1632 lithium battery
●Batteries can be purchased at your Toyota dealer, local electrical appli-
ance shops or camera stores.
●Replace only with the same or equivalent type recommended by the
manufacturer.
●Dispose of used batteries according to local laws.
■If the electronic key battery is depleted
The following symptoms may occur: ●The smart key system and wireless remote control will not function prop-
erly.
●The operational range will be reduced.
CAUTION
■Removed battery and other parts
These parts are small and if swallowed by a child, they can cause choking. Keep away from children. Failure to do so could result in death or serious injury.
NOTICE
■For normal operation after replacing the battery
Observe the following precautions to prevent accidents: ●Always work with dry hands.
Moisture may cause the battery to rust.
●Do not touch or move any other component inside the remote control. ●Do not bend either of the battery terminals.
461
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary.
STEP 1
STEP 2
Turn the “POWER” switch off. Vehicles with Solar Ventilation System: Turn the Solar Ventilation System off and make sure not to operate the Remote Air Condi- tioning System. Open the fuse box cover.
Engine compartment
Push the tab in and lift the lid off.
When closing, first hook the lid onto the two rear tabs.
Left side instrument panel
ITO43P127
Remove the lid.
STEP 3
After a system failure, see “Fuse layout and amperage rat- ings” (P. 465) for details about which fuse to check.
462
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
STEP 4
Remove the fuse.
type A
Only removed using tool.
fuse can be the pullout
STEP 5
Check if the fuse is blown.
Type A
ITY42C012
Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rating. The amper- age rating can be found on the fuse box lid.
463
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
Type B
Type C
Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rating. The amper- age rating can be found on the fuse box lid.
Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rating. The amper- age rating can be found on the fuse box lid.
ITO43P161
464
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
Fuse layout and amperage ratings
■ Engine compartment
FUSE
HTR
RDI
CDS
S-HORN
ENG W/P
ABS MAIN
NO.2
H-LP CLN
P-CON MTR
AMP NO.1
IGCT
10
11 DC/DC-S
Ampere
Circuit
50A 30A 30A 10A 30A
Air conditioning system Electric cooling fans Electric cooling fans No circuit Cooling system
7.5A
Anti-lock brake system
30A
30A
30A 30A 5A
Headlight cleaner
P position control system, trans-
mission
Audio system
PCU, IGCT NO.2, IGCT NO.3
Inverter and converter
P position control system, P posi-
tion switch
465
12 P CON MAIN
7.5A
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
FUSE
Ampere
Circuit
13 AM2
14 ECU-B2
15 MAYDAY
16 ECU-B3
17 TURN & HAZ
18 ETCS
19 ABS MAIN
NO.1
20 H-LP LH LO
21 P/I 2
22 ABS MTR 1
23 ABS MTR 2
24 H-LP HI MAIN
25 DRL
26 AMP NO.2
27 P/I 1
28 EPS
29 H-LP RH LO
30 PCU
7.5A 7.5A 10A 10A 10A
10A
20A
15A
40A
30A 30A
20A
7.5A 30A 60A 60A 15A 10A
31
IGCT NO.2
10A
466
Power management system Smart key system, hybrid system MAYDAY Air conditioning system Turn signal lights Multiport fuel injection system/ sequential multiport fuel injection system
Anti-lock brake system
Left-hand headlight (low beam) P position control system, horn, headlight low beams, back-up lights Anti-lock brake system Anti-lock brake system Headlight high beams, daytime running lights Daytime running lights Audio system, navigation system IG2, EFI MAIN, BATT FAN Electric power steering Right-hand headlight (low beam) Inverter and converter Hybrid system, P position control system, power management sys- tem, multiport fuel injection sys- tem/sequential multiport fuel injection system
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
FUSE
32 MIR HTR
33 RAD NO.1
34 DOME
35 ECU-B
36 H-LP LH HI 37 H-LP RH HI
38 EFI NO.2
IGCT NO.3
39
40 SPARE
41 SPARE
42 SPARE
43 EFI MAIN
44 BATT FAN
45
IG2
Ampere
Circuit
10A 15A
10A
7.5A
10A 10A
10A
10A 30A 10A 7.5A
20A
10A
20A
Outside rear view mirror defoggers
Audio system, navigation system
Door courtesy lights, luggage
compartment light, personal light,
interior light, foot lights, vanity
lights, inside rear view mirror,
garage door opener
Smart key system, personal lights,
gauges and meters, emergency
flashers
Left-hand headlight (high beam)
Right-hand headlight (high beam)
Multiport fuel injection system/
sequential multiport fuel injection
system
Cooling system
Spare fuse
Spare fuse
Spare fuse
Multiport fuel injection system/
sequential multiport fuel injection
system, cooling system, EFI NO.2
Battery cooling fan
Multiport fuel injection system/
sequential multiport fuel injection
system, MET, IGN, power man-
agement system
PRIUS_OM_OM47857U_DVD_(U)
467
4-3. Do-it-yourself maintenance
■ Left side instrument panel
2 3
5 6
9 10
11
12
13
14
15 16
17 18
19
20 21
22
23 24 25 26
27 28 29 30
FUSE
CIG
Ampere
15A
ECU-ACC
10A
PWR OUTLET
SEAT HTR FR
SEAT HTR FL
DOOR NO.1
PSB
PWR SEAT FR
DBL LOCK
10 FR FOG 11 PWR SEAT FL 12 OBD 13 RR FOG
14 STOP
468
15A 10A 10A 25A 30A 30A 25A 7.5A 30A 7.5A 7.5A
10A
ITO43P133
Circuit
Power outlets Multiplex communication system, outside rear view mirrors, driver support system, audio system, navigation system, advanced parking guidance system, head-up display Power outlets Seat heater Seat heater Power door lock system Pre-Collision System Front passenger’s seat No circuit Front fog lights Driver’s seat On-board diagnosis system No circuit Stop lights, high mounted stop- light, brake system, driver support system, vehicle proximity notifica- tion system
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
FUSE
Ampere
Circuit
15 P FR DOOR 16 D FR DOOR 17 DOOR RR 18 DOOR RL 19 S/ROOF
20 ECU-IG NO.1
25A 25A 25A 25A 30A
10A
21 ECU-IG NO.2
10A
22 GAUGE
23 A/C
24 WASHER
10A
10A
15A
Power windows Power windows Power windows Power windows Moon roof Electric cooling fans, multiplex communication system, vehicle proximity notification system Driver support system, Pre-Colli- sion System, LKA system, inside rear view mirror, garage door opener, yaw rate & G sensor, brake system, electric power steering, navigation system, moon roof, tire pressure warning system, seat belt pretensioners, audio sys- tem, emergency flashers, turn sig- nal lights, windshield wipers, headlight cleaner Headlight leveling system, gauges and meters, emergency flashers, turn signal lights Air conditioning system, Solar Ventilation System, Remote Air Conditioning System Windshield washer
PRIUS_OM_OM47857U_DVD_(U)
469
4-3. Do-it-yourself maintenance
FUSE 25 RR WIP 26 WIP 27 MET
Ampere
20A 30A 7.5A
28
IGN
10A
29 PANEL
10A
30 TAIL
10A
Circuit
Rear window wiper and washer Windshield wipers Gauges and meters Brake system, driver support sys- tem, multiport fuel injection sys- tem/sequential multiport fuel injection system, SRS airbag sys- tem, front passenger occupant classification system (ECU and sensors), power management sys- tem, smart key system, front pas- senger’s seat belt reminder light Air conditioning system, personal light, transmission, P position switch, navigation system, Solar Ventilation System, Remote Air Conditioning System, advanced parking guidance system, head- light cleaner, front passenger’s seat belt reminder light, headlight leveling system, glove box light, clock, audio system, MPH or km/h switch Headlight leveling system, park- ing lights, tail lights, license plate lights, front fog lights, side marker lights
470
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■After a fuse is replaced
●If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (P. 473)
●If the replaced fuse blows again, have the vehicle inspected by your
Toyota dealer.
■If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
■When replacing light bulbs
Toyota recommends that you use genuine Toyota products designed for this vehicle. Because certain bulbs are connected to circuits designed to prevent overload, non-genuine parts or parts not designed for this vehicle may be unusable.
CAUTION
■To prevent system breakdowns and vehicle fire
Observe the following precautions. Failure to do so may cause damage to the vehicle, and possibly a fire or injury. ●Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
●Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
●Do not modify the fuses or fuse boxes. ■Fuse box near the power control unit
Never check or replace the fuses as there are high voltage parts and wiring near the fuse box. Doing so may cause electric shock, resulting in death or serious injury.
471
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
NOTICE
■Before replacing fuses
Have the cause of electrical overload determined and repaired by your Toyota dealer as soon as possible.
472
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance Light bulbs
You may replace the following bulbs by yourself. The difficulty level of replacement varies depending on the bulb. As there is a danger that components may be damaged, we recommend that replacement is carried out by your Toyota dealer. ■ Preparing for light bulb replacement
Check the wattage of the light bulb to be replaced. (P. 576)
■ Front bulb locations
Parking light (halogen headlights)
Headlight high beam (including daytime running lights for Canada)
Fog light (if equipped)
Headlight low beam (halogen headlights)
Front side marker light
Front turn signal light
473
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■ Rear bulb locations
Rear turn signal light
Back-up light
License plate lights
Replacing light bulbs
■ Headlight low beams (halogen headlights)
STEP 1
Turn the bulb base counterclock- wise.
474
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
Unplug pressing the lock release.
the connector while
ITO43P163
Replace the light bulb, and install the bulb base.
Align the 3 tabs on the light bulb with the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to check that it is not loose, turn the headlights on once and visually confirm that no light is leaking through the mounting.
475
STEP 2
STEP 3
STEP 4
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■ Headlight high beams (including daytime running lights for
Canada)
STEP 1
Turn the bulb base counterclockwise.
Vehicles with halogen headlights
Vehicles with LED headlights
STEP 2
Unplug pressing the lock release.
the connector while
ITO43P165
476
PRIUS_OM_OM47857U_DVD_(U)
STEP 3
STEP 4
4-3. Do-it-yourself maintenance
Replace the light bulb, and install the bulb base.
Align the 3 tabs on the light bulb with the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to check that it is not loose, turn the headlights on once and visually confirm that no light is leaking through the mounting.
477
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■ Parking lights (halogen headlights)
STEP 1
Turn the bulb base counterclock- wise.
STEP 2
Remove the light bulb.
STEP 3
When installing, reverse the steps listed.
ITO43P167
478
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■ Front side marker lights
STEP 1
Turn the bulb base counterclockwise.
Vehicles with halogen headlights
Vehicles with LED headlights
STEP 2
Remove the light bulb.
STEP 3
When installing, reverse the steps listed.
ITO43P167
PRIUS_OM_OM47857U_DVD_(U)
479
4-3. Do-it-yourself maintenance
■ Fog lights (if equipped)
STEP 1
Remove the fender liner bolt and clip and pull down the fender liner.
Unplug pressing the lock release.
the connector while
Turn the bulb base counterclock- wise.
STEP 2
STEP 3
480
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
STEP 4
When installing, reverse the steps listed. After installing the bulb base, shake the bulb base gently to check that it is not loose.
Insert the clip.
481
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■ Front turn signal lights
STEP 1
Remove the fender liner bolt and clip and pull down the fender liner. (P. 480)
For the U.S.A.
STEP 2
Turn the bulb base counterclock- wise.
STEP 3
Remove the light bulb.
482
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
For Canada
STEP 2
Turn the bulb base counterclock- wise.
STEP 3
Remove the light bulb.
STEP 4
When installing, reverse the steps listed.
ITO43P144
Insert the clip.
483
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
■ Rear turn signal lights and back-up lights
STEP 1
STEP 2
STEP 3
Open the back door and remove the cover.
To prevent damage, cover the tip of the screwdriver with a rag.
Turn the bulb base counterclock- wise.
Rear turn signal light Back-up light
Remove the light bulb. Rear turn signal light Back-up light
STEP 4
When installing, reverse the steps listed.
ITO43P147
484
PRIUS_OM_OM47857U_DVD_(U)
■ License plate lights
STEP 1
4-3. Do-it-yourself maintenance
Open the back door and remove the cover.
To prevent damage, cover the tip of the screwdriver with a rag.
STEP 2
Turn the bulb base counterclock- wise.
STEP 3
Remove the light bulb.
ITO43P149
STEP 4
When installing, reverse the steps listed.
ITO43P150
PRIUS_OM_OM47857U_DVD_(U)
485
4-3. Do-it-yourself maintenance
■ Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by your Toyota dealer. ● Headlight low beams (LED headlights) ● Parking lights (LED headlights) ● Stop lights ● Tail lights ● Rear side marker lights ● High mounted stoplight ● Daytime running lights (except for Canada)
■LED lights
The headlight low beams (LED headlights), parking lights (LED headlights), stop lights, tail lights, rear side marker lights, high mounted stoplight and daytime running lights (except for Canada) consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.
■Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations: ●Large drops of water have built up on the inside of the lens. ●Water has built up inside the headlight.
■When replacing light bulbs
P. 471
486
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
CAUTION
■Replacing light bulbs
●Be sure to stop the hybrid system and turn off the lights. Do not attempt to
replace the bulb immediately after turning off the lights. The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb. Also, if the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens. ●Do not attempt to repair or disassemble light bulbs, connectors, electric
circuits or component parts. Doing so may result in death or serious injury due to electric shock.
■To prevent damage or fire
Make sure bulbs are fully seated and locked.
487
PRIUS_OM_OM47857U_DVD_(U)
4-3. Do-it-yourself maintenance
488
PRIUS_OM_OM47857U_DVD_(U)
When trouble arises
5-1. Essential information
Emergency flashers ......... 490
If your vehicle needs
to be towed .................... 491
If you think something
is wrong ......................... 498
5-2. Steps to take in
an emergency
If a warning light turns
on or a warning
buzzer sounds ............... 499
If a warning message
is displayed .................... 513
If you have a flat tire......... 530
If the hybrid system
will not start.................... 545
If you lose your keys ........ 547
If the electronic key
does not operate
properly.......................... 548
If the 12-volt battery
is discharged.................. 550
If your vehicle
overheats ....................... 556
If the vehicle becomes
stuck .............................. 561
If your vehicle has
to be stopped in
an emergency ................ 563
489
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information Emergency flashers
The emergency flashers are used to warn other drivers when the vehicle has to be stopped in the road due to a breakdown, etc.
Press the switch.
All the turn signal lights will flash. To turn them off, press the switch once again.
■Emergency flashers
If the emergency flashers are used for a long time while the hybrid system is not operating (while the “READY” indicator is not illuminated), the 12-volt battery may discharge.
490
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Before towing
The following may indicate a problem with your hybrid transmission. Contact your Toyota dealer before towing. ● The hybrid system is operating but the vehicle will not move. ● The vehicle makes an abnormal sound. If there is a malfunction in the P position control system, the smart key system or the immobilizer system, or if the 12-volt battery is dis- charged, the vehicle cannot be towed with the front wheels on the ground, as the front wheels may be locked. In this case, transport the vehicle with both front wheels or all four wheels lifted.
491
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information
Emergency towing
If a tow truck is not available in an emergency, your vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet(s). This should only be attempted on hard surfaced roads for short distances at under 18 mph (30 km/h). A driver must be in the vehicle to steer and operate the brakes. The vehicle’s wheels, drive train, axles, steering and brakes must be in good condition.
492
PRIUS_OM_OM47857U_DVD_(U)
Installing towing eyelets
STEP 1
STEP 2
STEP 3
5-1. Essential information
Remove the eyelet cover using a flathead screwdriver.
To prevent damage, cover the tip of the screwdriver with a rag.
Insert the towing eyelet into the hole and tighten partially by hand.
Tighten down the towing eyelet securely using a wheel nut wrench.
493
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information
Towing with a sling-type truck
Do not tow with a sling-type truck to prevent body damage.
Towing with a wheel-lift type truck
From the front
Release the parking brake.
From the rear
Use a towing dolly under the front wheels.
494
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information
If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45. Do not overly tighten the tie downs or the vehicle may be damaged.
Using a flat bed truck
■Before emergency towing
STEP 2
STEP 1
Turn the “POWER” switch to ON mode. Do not turn the “POWER” switch to ACCESSORY mode. Shift the shift position to N. Release the parking brake. ■Emergency towing eyelet location
STEP 3
P. 530
495
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information
CAUTION
■Caution while towing
●Use extreme caution when towing the vehicle.
Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelets and the cables or chains. Always be cautious of the surroundings and other vehicles while towing.
●Do not turn the “POWER” switch off.
This may lead to an accident as the front wheels will be locked by the parking lock.
●If the hybrid system is off, the power assist for the brakes and steering will
not function, making steering and braking more difficult.
■Installing towing eyelets to the vehicle
Make sure that towing eyelets are installed securely. If not securely installed, towing eyelets may come loose during towing. This may lead to accidents that cause serious injury or even death.
496
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information
NOTICE
■To prevent damaging the vehicle
When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.
■To prevent causing serious damage to the hybrid transmission when
towing using a wheel-lift type truck Never tow this vehicle from the rear with the front wheels on the ground.
■To prevent body damage when towing with a sling-type truck
Do not tow with a sling-type truck, either from the front or rear.
■To prevent causing serious damage to the hybrid transmission in
emergency towing Never tow a vehicle from the rear with four wheels on the ground. This may cause serious damage to the hybrid transmission.
497
PRIUS_OM_OM47857U_DVD_(U)
5-1. Essential information If you think something is wrong
If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms
● Fluid leaks under the vehicle
(Water dripping from the air conditioning after use is normal.)
● Flat-looking tires or uneven tire wear ● High engine coolant temperature warning light flashes or
comes on
■ Audible symptoms
● Changes in exhaust sound ● Excessive tire squeal when cornering ● Strange noises related to the suspension system ● Pinging or other noises related to the hybrid system
■ Operational symptoms
● Engine missing, stumbling or running roughly ● Appreciable loss of power ● Vehicle pulls heavily to one side when braking ● Vehicle pulls heavily to one side when driving on a level road ● Loss of brake effectiveness, spongy feeling, pedal almost
touches the floor
498
PRIUS_OM_OM47857U_DVD_(U)
5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds
Calmly perform the following actions if any of the warning lights comes on or flashes. If a light comes on or flashes, but then goes off, this does not necessarily indicate a malfunction in the system. However, if this continues to occur, have the vehicle inspected by your Toyota dealer.
Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous.
The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer.
Warning light
Warning light/Details
Brake system warning light and warning buzzer (red indicator)* • Low brake fluid • Malfunction in the brake system This light also comes on when the parking brake is not released. If the light turns off after the parking brake is fully released, the system is operating normally.
(U.S.A.)
(Canada)
*: Parking brake engaged warning buzzer:
A buzzer will sound if the vehicle is driven at a speed of approximately 3 mph (5 km/h) or more.
499
PRIUS_OM_OM47857U_DVD_(U)
5-2. Steps to take in an emergency
Stop the vehicle immediately.
The following warning indicates the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer.
Warning light
Warning light/Details
Charging system warning light Indicates a malfunction in the vehicle’s charging system
High coolant temperature warning light Indicates that the coolant temperature is too high Changes from a flashing to a solid light when the engine coolant temperature increases.
500
PRIUS_OM_OM47857U_DVD_(U)
5-2. Steps to take in an emergency
Have the vehicle inspected by your Toyota dealer immediately.
Failure to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately.
Warning light
Warning light/Details
(U.S.A.)
(Canada)
(U.S.A.)
(Canada)
Malfunction indicator lamp Indicates a malfunction in: • The hybrid system; • The electronic engine control system; or • The electronic throttle control system
SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system
ABS warning light Indicates a malfunction in: • The ABS; or • The brake assist system
Electric power steering system warning light (warn- ing buzzer) Indicates a malfunction in the EPS system
501
PRIUS_OM_OM47857U_DVD_(U)
5-2. Steps to take in an emergency
Warning light