will get an accurate cold tire pressure reading.
(cid:1) Always use a tire pressure gauge. The appearance of a tire can be mis- leading. Besides, that are even just a few pounds off can degrade ride and handling.
tire pressures
213
(cid:1) Take special care when adding air to the compact spare tire. The smaller tire size can gain pressure very quick- ly. Add compressed air in small quanti- ties and check the pressure often until it reaches the specified pressure.
(cid:1) Do not bleed or reduce tire pressure after driving. It is normal for the tire pressure to be higher after driving.
(cid:1) Never exceed
the vehicle capacity weight. The passenger and luggage weight should be located so that the vehicle is balanced.
(cid:1) Be sure to reinstall the tire inflation valve caps. Without the valve caps, dirt or moisture could get the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as possible.
into
214
Checking and replacing tires
Tread wear indicator
82p004b
CHECKING YOUR TIRES
Check the tire tread for the tread wear
indicators. If the indicators show, re-
place the tires.
The
tires on your Toyota have built–in
tread wear indicators to help you know
when the tires need replacement. When
the tread depth wears to 1.6 mm (0.06
in.) or less, the indicators will appear. If
you can see the indicators in two or more
adjacent grooves, the tire should be re-
placed. The lower the tread, the higher
the risk of skidding.
The effectiveness of snow tires is lost
if the tread wears down below 4 mm
(0.16 in.).
Check the tires regularly for damage such as cuts, splits and cracks. If any damage is found, consult with a techni- cian and have the tire repaired or re- placed. Even if the damage does not appear seri- ous, a qualified technician should examine the damage. Objects which have pene- trated the tire may have caused internal damage. Any tires which are over 6 years old must be checked by a qualified techni- cian even if damage is not obvious. Tires deteriorate with age even have never or seldom been used. This also applies to the spare tire and tires stored for future use. REPLACING YOUR TIRES When replacing a tire, use only the same size and construction as original- ly installed and with the same or great- er load capacity. Using any other size or type of tire may seriously affect handling, ride, speedome- ter/odometer calibration, ground clearance, and clearance between the body and tires or snow chains.
they
if
tire
the wheel
When a is replaced, should always be balanced. An unbalanced wheel may affect vehicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.
CAUTION
(cid:1) Do not mix radial, bias belted, or bias–ply tires on your vehicle. It can cause dangerous handling char- acteristics, resulting in loss of con- trol.
(cid:1) Do not use tires or wheels other recom-
the manufacturer’s
than mended size.
NOTICE
Do not use tires of different brands, sizes and constructions. This may damage the drive system.
Toyota recommends all four tires, or at
least both front or rear tires be re-
placed as a set.
See “If you have a flat tire†on page 173
in Section 5 for tire change procedure.
Rotating tires
82p005a
To equalize tire wear and help extend
tire life, Toyota recommends that you
rotate your tires according to the main-
tenance schedule. (For scheduled main-
tenance information, please refer to the
“Scheduled Maintenance Guide†or
“Owner’s Manual Supplementâ€.) Howev-
er, the most appropriate timing for tire
rotation may vary according to your
driving habits and road surface condi-
tions.
See “If you have a flat tire†on page 173
in Section 5 for tire change procedure.
215
Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select the same size, construction and load capacity as the original tires on your Toyota. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions.
SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires, you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replacing.
CAUTION
(cid:1) Do not drive with the snow tires
incorrectly inflated.
(cid:1) Never drive over 120 km/h (75 mph)
with any type of snow tires.
NOTICE
Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicles as well as the tire.
rotating
tires, check
When for uneven wear and damage. Abnormal wear is usu- ally caused by incorrect tire pressure, im- proper wheel alignment, out–of–balance wheels, or severe braking.
CAUTION
Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.
216
TIRE CHAIN SELECTION Use the tire chains of correct size. Regulations regarding the use of tire chains vary according to location or type of road, so always check them before installing chains. CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer. If wheel covers are used, they will be scratched by the chain band, so remove the covers before putting on the chains.
rear driving
0.5—1.0
the
CAUTION
(cid:1) Do not exceed 50 km/h (30 mph) or recom- is
the chain manufacturer’s mended speed lower.
limit, whichever
(cid:1) Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.
(cid:1) Avoid sharp turns or locked–wheel braking, as use of chains may ad- versely affect vehicle handling.
(cid:1) When driving with chains installed, be sure to drive carefully. Slow down before entering the curves to avoid losing control of the vehicle. Otherwise an accident may occur.
NOTICE
Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicle as well as the tire.
Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace damaged wheels, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. This must be observed on compact spare tire, too. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.
217
Aluminum wheel precautions
(cid:1) When
aluminum wheels,
check
tight
after driving your vehicle the first 1600
km (1000 miles).
the wheel nuts are
installing that
repaired, or (cid:1) If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).
rotated, tires, check
that
(cid:1) When using tire chains, be careful not
to damage the aluminum wheels.
(cid:1) Use only the Toyota wheel nuts and for your aluminum
wrench designed wheels.
(cid:1) When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.
(cid:1) As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.
Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.
218
SECTION 8– 3
DO–IT–YOURSELF MAINTENANCE Electrical components
Checking auxiliary battery condition Auxiliary battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
220
221
221
223
223
219
Checking auxiliary battery condition— —Precautions
CAUTION
AUXILIARY BATTERY PRECAUTIONS When the auxiliary battery must be replaced, use the Prius designated battery. The auxiliary battery produces flam- mable and explosive hydrogen gas. (cid:1) Do not cause a spark from the bat-
tery with tools.
(cid:1) Do not smoke or light a match near
the battery.
The electrolyte contains poisonous and corrosive sulfuric acid. (cid:1) Avoid contact with eyes, skin or
clothes.
(cid:1) Never ingest electrolyte. (cid:1) Wear protective safety glasses when
working near the battery.
(cid:1) Keep children away from the bat-
tery.
220
EMERGENCY MEASURES (cid:1) If electrolyte gets
in your eyes, flush your eyes with clean water and get immediate medical atten- tion. If possible, continue to apply water with a sponge or cloth while en route to the medical office.
(cid:1) If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burn, get medical attention immediately.
(cid:1) If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.
(cid:1) If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.
—Checking auxiliary battery exterior
Terminals
Ground cable
Hold–down clamp
Check the battery for corroded or loose terminal connections, cracks, or loose hold–down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.
b. If the terminal connections are loose, their clamp nuts—but do not
tighten overtighten.
c. Tighten
the hold–down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.
NOTICE
(cid:2) Be sure the hybrid system and all accessories are off before perform- ing maintenance.
(cid:2) When checking the battery, remove the ground cable from the negative terminal (“—†mark) first and rein- stall it last.
(cid:2) Be careful not to cause a short cir-
cuit with tools.
(cid:2) Take care no solution gets into the
battery when washing it.
Auxiliary battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
2. Make sure the power switch on the recharger is off when connecting the charger cables to the battery and when disconnecting them.
CAUTION
(cid:1) Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.
(cid:1) Only do a slow charge (3.5A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.
NOTICE
Never recharge the battery with the hybrid system on. Also, be sure all accessories are turned off.
Checking and replacing fuses
Type A
Good
Blown
Type B
83p003
Good
Blown
Type C
Good
Blown
221
the new
If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.
CAUTION
Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.
Type A fuses can be pulled out by the pull–out tool. The location of the pull–out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “DOME†or “OBDII†fuse, which may be dispens- able for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close as possible to, the rating. If the amperage is fuse might blow out again. but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.
that specified,
lower
than
the
83p004a
If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations†on page 201 in Sec- tion 8–1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull a suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See page 235 in Section 9 for the functions controlled by each circuit.
222
Adding washer fluid
83p009
NOTICE
Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.
If any washer does not work, the wash- er tank may be empty. Check the wash- er fluid level on the level gauge. If the washer fluid level is below “LOWâ€, add washer fluid. You may use plain water as washer fluid. in cold areas where tempera- However, tures freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.
range below
following
illustrations show how
Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.
CAUTION
Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.
NOTICE
Only use a bulb of the listed type.
223
the
fogging
The inside of the lens of exterior lights such as headlights may temporarily fog up when the lense becomes wet in the rain or in a car wash. This is not a problem because the temperature difference between the outside and the windshield fogged up in the rain. However, if there is a large drop of water on the inside of the lense, or if there is water pooled light, contact your Toyota dealer.
is caused by
inside of
lense,
inside
just
like
the
the
Light bulbs
Headlights Parking lights Front turn signal lights Rear turn signal lights Stop and tail lights Back–up lights License plate lights High mounted stop- light Interior light Personal light Trunk light
Bulb
No.
— 60/55
947
—
21
7440
7443
921
—
9419
—
—
194
21
21/5
16
3.8
A: HB2 Halogen bulbs B: Single end bulbs C: Wedge base bulbs D: Double end bulbs
224
Type
—Headlights
83p010
1. Open the hood.
RIGHT–HAND HEADLIGHT: Remove the clip and take out the air cleaner inlet. Remove and install the clip as shown in the following illustration. LEFT–HAND HEADLIGHT: Remove the upper part of the washer fluid reser- voir while pinching the lever.
83p011
83p013
83p014
Removing clip
83p012
Installing clip
2. Unplug the connector. Remove the
rubber cover.
If the connector is tight, wiggle it.
3. Release
the bulb retaining spring and remove the bulb along with the socket. Install a new bulb into the socket and return the bulb retaining spring to its original position.
To install a bulb, align the tabs of the bulb with the cutout of the mounting hole.
225
—Parking lights
—Front turn signal lights
83p015
83p016
83p010
4. Install the rubber cover as shown, and snuggle on the boss. Insert the connector.
Make sure the rubber cover fits snugly on the connector and the headlight body. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
83p017
RIGHT SIDE FRONT TURN SIGNAL LIGHT: Remove the upper part of the washer fluid reservoir as shown in the illustration above. Remove and install the clip as shown in the following illustration. LEFT SIDE FRONT TURN SIGNAL: Re- move the upper part of the washer fluid reservoir while pinching the lever.
226
—Rear turn signal, stop/tail and back–up lights
83P011
83p018
83p023
Removing clip
83p012
83p019
83p029
Installing clip
227
—High mounted stoplight
83p025
83p005
83p007
a: Tail light b: Rear turn signal light c: Back–up light d: Stop/tail light
Use a flat–bladed screwdriver.
Use a flat–bladed screwdriver.
83p006
83p008
228
Use a Phillips–head screwdriver.
—License plate lights
83p026
83p028a
Remove the cover clips.
83p027
229
230