CAUTION
■While driving
●Keep the back door closed while driving.
If the back door is left open, it may hit near-by objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the back door before driving.
●Before driving the vehicle, make sure that the back door is fully closed. If the back door is not fully closed, it may open unexpectedly while driving, causing an accident.
●Never let anyone sit in the luggage compartment. In the event of sudden
braking or an accident, they are susceptible to death or serious injury.
■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not allow children to play in the luggage compartment.
If a child is accidentally locked in the luggage compartment, they could have heat exhaustion or other injuries.
●Do not allow a child to open or close the back door.
Doing so may cause the back door to move unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing back door.
54
LC200_OM_OM60L09U_(U)
1
1-2. Opening, closing and locking the doors
CAUTION
■Operating the back door
Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ●Remove any heavy loads, such as snow and ice, from the back door before opening it. Failure to do so may cause the back door suddenly shut again after it is opened.
●When opening or closing the back door, thoroughly check to make sure
the surrounding area is safe.
●If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
●Use caution when opening or closing the back door in windy weather as it
may move abruptly in strong wind.
●The back door may suddenly shut if it is not opened fully. It is more difficult to open or close the back door on an incline than on a level surface, so beware of the back door unexpectedly opening or closing by itself. Make sure that the back door is fully open and secure before using the luggage com- partment.
●When closing the back door, take extra care to prevent your fingers etc. from being caught.
●When closing the back door, make sure to press it lightly on its outer surface. If the back door handle is used to fully close the back door, it may result in hands or arms being caught.
55
LC200_OM_OM60L09U_(U)
1-2. Opening, closing and locking the doors
CAUTION
●Do not pull on the back door damper stay to close the back door, and do
not hang on the back door damper stay. Doing so may cause hands to be caught or the back door damper stay to break, causing an accident.
●If a bicycle carrier or similar heavy object is attached to the back door, it may suddenly shut again after being opened, causing someone’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recommended.
NOTICE
■Back door damper stays
The back door is equipped with damper stays that hold the back door in place. Observe the following precautions. Failure to do so may cause damage to the back door damper stay, resulting in malfunction.
Damper stay
●Do not attach any foreign objects, such as stickers, plastic sheets, or adhesives to the damper stay rod.
●Do not touch the damper stay rod with
gloves or other fabric items.
●Do not attach any accessories other than genuine Toyota parts to the back door.
●Do not place your hand on the damper
stay or apply lateral forces to it.
56
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats
angle
control
Seat position fore/aft control switch Seatback switch Seat cushion (front) angle control switch Vertical switch Lumbar switch (driver’s side only)
support
height
control
control
Active head restraint
When the occupant’s lower back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward and upward to help reduce the risk of whiplash on the seat occupant.
57
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■Active head restraint
Even small forces applied to the seatback may cause the head restraint to move. Pushing up a locked head restraint forcibly may make the inner struc- ture of the head restraint appear. This does not indicate a problem.
During rear-end collision
Inner structure
CAUTION
■Seat adjustment
●Be careful that the seat does not hit passengers or luggage. ●Do not recline the seat more than necessary when the vehicle is in motion
to reduce the risk of sliding under the lap belt. If the seat is too reclined, during an accident the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury. Adjustments should not be made while driving as the seat may unexpect- edly move and cause the driver to lose control of the vehicle.
58
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats
Second seat
Third seat
Seatback angle adjustment lever Seat position adjustment lever
59
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Tumbling the second seats and third seat entry
For easy access to the third seat, perform
second seats”. (P. 61)
■ Before tumbling the second seats
STEP 1
STEP 1
in “Tumbling the
Stow the seat belt buckles and lower the head restraints to the lowest position.
STEP 2
Pass the outer seat belts through the seat belt hangers and secure the seat belt plates.
This prevents the shoulder belt from being damage. Make sure that the seat belts are removed from the hangers before using them.
ITY13C013a
60
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Tumbling the second seats
STEP 1
Fold down the seatback while pulling seatback angle adjustment lever, and swing the whole seat up and forward.
the
STEP 2
Hook the holding strap to the assist grip and secure the seat by pulling its free end.
When returning the second seat to its original position, stow the holding strap.
61
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
STEP 3
Remove the seat hook covers from the back of the seat cush- ion, and install them on the seat hooks.
When returning the second seat to its original position, remove the seat hook covers from the floor and install them in the back of the seat cushion.
ITY13C025
■If you cannot raise the left side seatback
STEP 1
Lift the seatback until it stops.
STEP 2
ITY13C139a
Lower the seatback a little then lift it again.
62
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Folding up the third seats
■ Before folding up the third seats
STEP 1
Stow the seat belts buckles.
STEP 2
Stow the center head restraint in the seatback. (P. 75)
ITY13C018
STEP 3
Pass the outer seat belts through the seat belt hangers and secure the seat belt plates.
This prevents the shoulder belt from being damage. Make sure that the seat belts are removed from the hangers before using them.
ITY13C021a
STEP 4
Stow the center seat belt tabs in the cover set in the roof. (P. 78)
63
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Folding up the third seats
STEP 1
Fold down the head restraints while pulling the head restraint angle lever.
STEP 2
STEP 3
ITY13C022
Push the seatback angle levers and fold the third seatbacks.
Pull the seat leg lock release levers.
The seat will rise, and the seat- back striker will also automatically sit up. Before raising, make sure that the handle on the rear of the seat- back is secure.
64
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
STEP 4
Secure the seats by the strikers.
STEP 5
Remove the seat hook covers from the back of the seat cush- ion, and install them on the seat hooks.
ITY13C030
■ Returning the third seats
STEP 1
Remove the seat hook covers from the floor and install them into the back of the seat cushion.
STEP 2
Unlock the seats by pulling the stowed seat lock release levers and lower the seats to its original position.
65
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
STEP 3
Secure the seats by the strikers.
STEP 4
Pull the handle and raise the seatbacks.
Fix the handle securely in its orig- inal position after use.
STEP 5
Raise the head restraints.
66
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment
Do not recline the seat more than necessary when the vehicle is in motion, to reduce the risk of sliding under the lap belt. If the seat is too reclined, during an accident the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury.
■When the seatback is folded
●Do not sit on or place anything on the seatback while driving. ●Be sure to install the seat hook covers on the seat hooks, or you may get
burned when they become hot.
■When returning the seatbacks to their original position
Observe the following precautions. Failure to do so may result in death or serious injury. ●Be careful not to get your hands or feet pinched in the seat. ●Make sure the seats are securely locked. Failure to do so will prevent the
seat belt from operating properly.
●Check that the seat belts are not twisted or caught under the seat. ●Arrange the seat belts in the proper positions for ready use.
■Avoiding damage to seat components
Do not hang or attach anything on the seatback striker.
NOTICE
■Before tumbling, folding up the seats
The seat belts and buckles must be stowed.
■After returning the third seat
Make sure that the handle on the rear of the seatback has been secured.
67
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Driving position memory system
Your preferred driving position (the position of the driver’s seat,
steering wheel and outside rear view mirrors) can be entered into the
computer’s memory and recalled with the touch of a button. It is also
possible to set this function to activate automatically when the
doors are unlocked.
Three different driving positions can be entered into memory.
■ Entering a position to memory
STEP 1
Turn the “ENGINE START STOP” switch to IGNITION ON mode. Adjust the driver’s seat, steering wheel, and outside rear view mirrors to the desired positions.
STEP 2
STEP 3
STEP 3
SET
SET
While pressing the “SET” but- ton, or within 3 seconds after the “SET” button is pressed, press and hold button “1”, “2” or “3” until the signal beeps.
If the selected button has already been preset, the previ- ously recorded position will be overwritten.
ITY13C036
68
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Recalling the memorized position Check that the shift lever is set in “P”.
STEP 1
Turn the “ENGINE START STOP” switch to IGNITION ON mode.
STEP 2
SET
Press button “1”, “2” or “3” to recall the desired position.
SET
ITY13C038
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before performing the following:
Using the wireless remote control
STEP 1
Turn the “ENGINE START STOP” switch to OFF after closing the driver’s door.
STEP 2
SET
While pressing the desired but- ton (“1”, “2” or “3”), press on the wireless remote control until the signal beeps.
the driver’s door
The driving position is recalled when is unlocked using the entry function or wireless remote control and the driver’s door is opened.
ITY13C130
69
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
To prevent unintended triggering of the alarm, open and close a door once after a driving position has been recorded. (If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm. (P. 107)
Using the door lock switch
Carry only the key to which you want to link the driving position. If 2
or more keys are in the vehicle, the driving position cannot be
linked properly.
STEP 1
Turn the “ENGINE START STOP” switch to OFF after closing the driver’s door.
STEP 2
While pressing the desired but- ton (“1”, “2”, or “3”), press the lock or unlock side on the door lock switch until the signal beeps.
the driver’s door
The driving position is recalled when is unlocked using the entry function or wireless remote control and the driver’s door is opened.
70
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
■Canceling the linked door unlock operation
STEP 1
STEP 2
Turn the “ENGINE START STOP” switch to OFF after closing the driver’s door. Using the wireless remote control: While pressing “SET” button, press button on the wireless remote control until the signal beeps. Using the door lock switch: While pressing “SET” button, press the lock or unlock side on the door lock switch until the signal beeps.
■Retained accessory power
●Each memorized position (except for the steering wheel position) can be activated within 3 minutes after the driver’s door is opened, even if the “ENGINE START STOP” switch is turned off.
●Each memorized position (except for the steering wheel position) can be activated within 60 seconds after the driver’s door is closed, even if the “ENGINE START STOP” switch is turned off.
■To cancel seat position recall
Perform any one of the following operations. ●Press the “SET” button ●Press button “1”, “2” or “3”. ●Adjust the seat using the switches (only cancels seat position recall) ●Adjust the steering wheel using the tilt and telescopic steering control
switch (only cancels steering wheel position recall)
■If the battery is disconnected
The memorized positions must be reset because the computer’s memory is erased when the battery is disconnected.
CAUTION
■Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas- senger or squeeze your body against the steering wheel.
71
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints
Head restraints are provided for all seats.
Front seats
Vertical adjustment
Up Down Push the head restraint up or down while pressing the lock release button.
Angle adjustment
Vertical adjustment
Up Pull the head restraint up. Down lock Press and hold release button when lowering the head restraint.
the
Lock release button
Second seats
Lock release button
72
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Third outboard seats
To fold
Pull the head restraint angle lever to fold the head restraint.
ITY13C040
■Adjusting the height of the head restraints
Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.
■Adjusting the second center seat head restraint
Always raise the head restraint one level from the stowed position when using.
73
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■Removing the head restraints
Front seats
STEP 1
Push a flathead screwdriver into the slot. The slot is located on the right side of the right head restraint anchor.
STEP 2
While pressing in the flathead screwdriver, pull up the head restraint.
Second seats
Pull the head restraint up while pressing the lock release button.
Pull the head restraint up while pressing the lock release button.
Lock release button
Third center seat
Lock release button
74
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Third outboard seats
STEP 1
Push a flathead screwdriver into the slot. The slot is located on the left side of the left head restraint anchor.
ITY13C035
STEP 2
While pressing in the flathead screwdriver, pull up the head restraint.
■Installing the head restraints
STEP 1
STEP 2
Align the head restraint with the installation holes. Push down the head restraint to the lock position.
■When not using the third center seat head restraint
Open the zipper on the back of the third seat and stow the head restraint inside.
ITY13C043
CAUTION
■Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure
they are locked in position.
●Do not drive with the head restraints removed.
75
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts
Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts
● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der.
● Position the lap belt as low
as possible over the hips.
● Adjust the position of the seatback. Sit up straight and well back in the seat. ● Do not twist the seat belt.
■ Fastening and releasing the seat belt
Fastening the belt Push the tab into the buckle until a clicking sound is heard. Releasing the belt Press the release button.
Release button
76
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Fastening and releasing the third center seat belt
STEP 1
Pull out the tab
STEP 2
Tab B
ITY13C120
Push tab B into buckle B until a clicking sound is heard
Buckle B
STEP 3
Tab A
Release button
CENTER
Buckle A
ITI13C190
Push tab A into buckle A until a clicking sound is heard
To release, push the release button on buckle A.
77
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Releasing and storing the third center seat belt
STEP 1
Push the release button on buckle A
STEP 2
Buckle B
Buckle B
STEP 3
Tab A
Buckle A
Push either the mechanical key or tab A into buckle B
When releasing and storing the seat belt, hold the belt while winding it back gently
Tab A
Tab B
Put tabs A and B together and stow them in the holder
reattach
To the seat belt, reverse the above procedure, pulling out the tabs and insert- ing tab B into buckle B
78
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Adjusting the height of the belt (front and second outboard
seats)
Down Up
Move the height adjuster up and down as needed until you hear a click.
ITY13C055
Seat belt pretensioners (front and second outboard seats)
The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision or a vehicle rollover.
The pretensioner may not acti- vate in the event of a minor frontal impact, a side impact or a rear impact.
79
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Pre-collision seat belts (front seats of vehicles with pre-collision system)
Brake-linked pre-collision system If the system determines that emergency braking is being per- formed or the vehicle is out of control, the front seat belts will retract.(P. 289) Radar type pre-collision system If the system determines that a collision is unavoidable, the front seat belts will retract before the collision. (P. 289)
■Emergency locking retractor (ELR)
The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around fully.
■Automatic locking retractor (ALR)
When a passenger’s shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (P. 140)
80
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■When the third center seat belt cannot be extended
Put your fingers between the seat belt and the holder. Pull the seat belt forcefully in the direction of the arrow and then release it to unlock.
■Child seat belt usage
The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriately for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. (P. 135) ●When the child becomes large enough to properly wear the vehicle’s
seat belt, follow the instructions on P. 76 regarding seat belt usage.
■Replacing the belt after the pretensioner has been activated
If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.
■Seat belt extender
If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.
they are not
ITY13C060
81
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failing to do so may cause death or serious injury. ■Wearing a seat belt
●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt
for more than one person at the same time, including children.
●Children should be seated in the rear seat and always use a seat belt and/
or an appropriate child restraint system.
●Do not recline the seat any more than necessary to achieve a proper seat- ing position. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.
●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.
■Pregnant women
Obtain medical advice and wear the seat belt in the proper way. (P. 76) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking, sudden swerv- ing or a collision.
■People suffering illness
Obtain medical advice and wear the seat belt in the proper way. (P. 76)
82
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■When children are in the vehicle
Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
■Seat belt pretensioners
●Do not place anything, such as a cushion, on the front passenger’s seat. Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the seat belt pretensioner for the front passenger’s seat may not activate in the event of a collision.
●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.
■Adjustable shoulder anchor
Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (P. 79)
■When using the third center seat belt
Do not use the third center seat belt with either buckle released. Fastening only one of the buckles may result in death or serious injury in case of sudden braking, sudden swerving or a collision.
83
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat belt damage and wear
●Do not damage the seat belts by allowing the belt, plate or buckle to be
jammed in the door.
●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.
●Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer.
●Replace the seat assembly, including the belts, if your vehicle has been
involved in a serious accident, even if there is no obvious damage.
●Do not attempt to install, remove, modify, disassemble or dispose of a seat belt. Have any necessary repairs carried out by your Toyota dealer. Inap- propriate handling of the pretensioner may cause it to activate or operate improperly and may cause death or serious injury.
■Using a seat belt extender
●Do not wear the seat belt extender, if you can fasten the seat belt without
the extender.
●Do not use the seat belt extender when installing a child restraint system, because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of a sudden stop, sudden swerve or accident.
●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.
84
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
NOTICE
■When using a seat belt extender
When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
85
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel
The steering wheel can be adjusted to a comfortable position while the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.
Up Down Toward the driver Away from the driver
Auto tilt away
the
When “ENGINE START STOP” switch is OFF, the steer- ing wheel returns to its stowed position by moving up and away to enable easier driver entry and exit.
Switching to ACCESSORY or IGNITION ON mode will return the steering wheel to the original position.
86
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
■One-touch adjustment of the steering position
A desired steering position can be entered to memory and recalled automat- ically by the driving position memory. (P. 68)
CAUTION
■While driving
Do not adjust the steering wheel. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.
87
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror
The rear view mirror’s position can be adjusted to enable sufficient confirmation of the rear view in accordance with the driver’s seating posture.
Adjusting the height of the rear view mirror
Adjust the height of the rear view mirror by moving it up and down.
Automatic anti-glare function
Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced.
Changing automatic anti-glare function mode ON/OFF
ON OFF When the automatic anti-glare function is in ON mode, the indi- cator illuminates. The function will be set to ON mode each time the “ENGINE START STOP” switch is turned to IGNITION ON mode. Pressing the button turns the function to OFF mode. (The indi- cator also turns off.)
88
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■To prevent sensor error
To ensure correct functioning of the sen- sors, do not touch or cover the sensors.
CAUTION
■While driving
Do not adjust the position of the mirror. Doing so may lead to mishandling of the vehicle and an accident, or result- ing in death or serious injury.
89
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors
Mirror angle can be adjusted.
STEP 1
Select a mirror to adjust
Left Right
STEP 2
Adjust the mirror
Up Right Down Left
Folding back the mirrors
Press the switch
Pressing again will extended the mirrors.
90
LC200_OM_OM60L09U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
■Mirror angle can be adjusted when
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.
■When the mirrors are fogged up
The outside rear view mirrors can be cleared using the mirror defoggers. Turn on the rear window defogger to turn on the outside rear view mirror defoggers. (P. 351)
■Auto anti-glare function
When the anti-glare inside rear view mirror is set to auto mode, the outside rear view mirrors will activate in conjunction with the anti-glare inside rear view mirror to reduce reflected light. (P. 88)
■Linked mirror function when reversing
When the mirror select switch is in the “L” or “R” position, the outside rear view mirrors will automatically angle downwards when the vehicle is revers- ing in order to give a better view of the ground. To disable this function, move the mirror select switch to the neutral position (between “L” and “R”).
■One-touch adjustment of the mirror angle
A desired mirror face angle can be entered to memory and adjusted with the touch of a button. (P. 68)
91
LC200_OM_OM60L09U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■While driving
Observe the following precautions. Failing to do so may result in losing control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●Do not adjust the mirrors. ●Do not drive with the mirrors folded back. ●Before driving, be sure to extend mirrors and make an adjustment prop-
erly.
■When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.
■When the mirror defoggers are operating
Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
NOTICE
■If ice should jam the mirror
Do not operate the control or scrape the mirror face. Use a spray de-icer to free the mirror.
92
LC200_OM_OM60L09U_(U)
1
1-4. Opening and closing the windows and moon roof Power windows
The power windows can be opened and closed using the following switches.
Lock switch
Closing One-touch closing* Opening One-touch opening* *:To stop the window partway, operate the switch in the opposite direction.
Press the switch down to lock passenger window switches.
Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.
93
LC200_OM_OM60L09U_(U)
1-4. Opening and closing the windows and moon roof
■The power windows can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
■Door lock linked window operation
The following functions can be used if customized at your Toyota dealer. ●The power windows can be opened and closed using the mechanical
key. (P. 46, 653)
●The power windows can be opened using the wireless remote control.
(P. 44)
●The power windows can be closed using the smart key system. (P. 33) ■Operating the power windows after turning the “ENGINE START STOP”
switch OFF The power windows can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned ACCESSORY mode or turned OFF. They cannot, however, be operated once the driver’s or front passenger’s door is opened.
■Jam protection function
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
94
LC200_OM_OM60L09U_(U)
1-4. Opening and closing the windows and moon roof
■When the power window does not close normally
If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the relevant door. ●After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the “ENGINE START STOP” switch is turned to IGNITION ON mode.
●If the window still cannot be closed even by carrying out the operation
explained above, initialize the function by performing the following proce-
dure.
STEP 1
Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed. Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.
STEP 2
STEP 3
If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
■Customization
Settings (e.g. linked door lock operation) can be changed. (Customizable features P. 694)
95
LC200_OM_OM60L09U_(U)
1-4. Opening and closing the windows and moon roof
CAUTION
■Closing the windows
Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
●Do not allow children to operate the power windows.
Closing a power window on someone can cause death or serious injury.
■Jam protection function
●Never try jamming any part of your body to activate the jam protection
function intentionally.
●The jam protection function may not work if something gets caught just
before the window fully closes.
96
LC200_OM_OM60L09U_(U)
1
1-4. Opening and closing the windows and moon roof Moon roof
Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing
■ Tilt up and down
Open Stops just before it is opened fully. Press the switch again to fully open. Close To stop partway, press the switch lightly.
Tilt up Tilt down To stop partway, press the switch lightly.
97
LC200_OM_OM60L09U_(U)
1-4. Opening and closing the windows and moon roof
■The moon roof can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
■Door lock linked moon roof operation
The following functions can be used if customized at your Toyota dealer. ●The moon roof can be opened and closed using the mechanical key.
(P. 46)
●The moon roof can be opened using the wireless remote control.
(P. 44)
●The moon roof can be closed using the smart key system. (P. 33)
■Operating the moon roof after turning the “ENGINE START STOP”
switch OFF The moon roof can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned OFF. It cannot, however, be operated once the driver’s or front passenger’s door is opened.
■Jam protection function
If an object is detected between the moon roof and the frame while closing or tilting down, travel is stopped and the moon roof opens slightly.
■If the moon roof cannot be closed automatically
Keep the switch depressed.
■To reduce moon roof wind noise
When the moon roof is opened automatically, it will stop slightly before the fully open position. Driving with the moon roof in this position can help reduce wind noise.
■Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.
98
LC200_OM_OM60L09U_(U)
STEP 2
STEP 3
STEP 2
STEP 3
STEP 4
1-4. Opening and closing the windows and moon roof
■When the moon roof does not close normally
Perform the following procedure:
●If the moon roof closes but then re-opens slightly
STEP 1
Stop the vehicle.
Press and hold the “CLOSE” switch.*1
The moon roof will close, reopen and pause for approximately 10
seconds.*2 Then it will close again, tilt up and pause for approxi-
mately 1 second. Finally, it will tilt down, open and close.
Check to make sure that the moon roof is completely closed and
then release the switch.
●If the moon roof tilts down but then tilts back up
STEP 1
Stop the vehicle.
Press and hold the “UP” switch*1 until the moon roof moves into the
tilt up position and stops.
Release the “UP” switch once and then press and hold the “UP”
switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up
position.*2 Then it will adjust slightly and pause for approximately 1
second. Finally, it will tilt down, open and close.
Check to make sure that the moon roof is completely closed and
then release the switch.
*1: If the switch is released at the incorrect time, the procedure will
have to be performed again from the beginning.
*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the “CLOSE” or “UP” switch, and the moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is com- pletely closed and then release the switch.
If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.
99
LC200_OM_OM60L09U_(U)
1-4. Opening and closing the windows and moon roof
■Moon roof open warning buzzer
The buzzer sounds and message is shown on the multi-information display in the instrument panel when the “ENGINE START STOP” switch is turned OFF and the driver’s door is opened with the moon roof open.
■Customization
Settings (e.g. linked door lock operation) can be changed. (Customizable features P. 694)
CAUTION
■Opening the moon roof
Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-
cle while it is moving.
●Do not sit on top of the moon roof.
■Closing the moon roof
Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where they could be caught when the moon roof is being operated.
●Do not allow children to operate the moon roof.
Closing the moon roof on someone can cause death or serious injury.
■Jam protection function
●Never try jamming any part of your body to activate the jam protection
function intentionally.
●The jam protection function may not work if something gets caught just
before the moon roof fully closes.
100
LC200_OM_OM60L09U_(U)
1
1-5. Refueling Opening the fuel tank cap
Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle
● Turn the “ENGINE START STOP” switch OFF and ensure that
all the doors and windows are closed.
● Confirm the type of fuel. (P. 102)
■ Opening the fuel tank cap
STEP 1
Pull the lever.
STEP 2
STEP 3
Turn the fuel tank cap slowly to open.
Hang the fuel tank cap on the back of the fuel filler door.
101
LC200_OM_OM60L09U_(U)
1-5. Refueling
Closing the fuel tank cap
When replacing the fuel tank cap, turn it until a clicking sound is heard.
After releasing your hand, the cap will turn slightly to the opposite direction.
■Fuel types
Use unleaded gasoline (Octane Rating 87 [Research Octane Number 91] or higher)
102
LC200_OM_OM60L09U_(U)
1
1-5. Refueling
CAUTION
■Refueling the vehicle
Observe the following precautions while refueling the vehicle. Failure to do so, may result in death or serious injury. ●Touch the vehicle or some other metal surface to discharge any static
electricity. Sparks resulting from discharging static electricity may cause the fuel vapors to ignite.
●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out the filler neck and cause injury.
●Do not allow anyone that has not discharged static electricity from their
bodies to come close to an open fuel tank.
●Do not inhale vaporized fuel.
Fuel contains substances that are harmful if inhaled.
●Do not smoke while refueling the vehicle.
Doing so may cause the fuel to ignite and cause a fire.
●Do not return to the vehicle or touch any person or object that is statically
charged. This may cause static electricity to build up, resulting in a possible ignition hazard.
■When replacing the fuel tank cap
Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Failure to do so may cause a fire or other incident which may result in death or serious injury.
103
LC200_OM_OM60L09U_(U)
1-5. Refueling
NOTICE
■Refueling
Do not spill fuel during refueling. Failing to do so may damage the vehicle, such as causing the exhaust sys- tems to operate abnormally or damaging fuel system components or the vehicle’s painted surface.
104
LC200_OM_OM60L09U_(U)
1
1-6. Theft deterrent system Engine immobilizer system
The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.
Vehicles with navigation system
The indicator light flashes after the “ENGINE START STOP” switch has been turned OFF to indicate that the system is operating. The indicator light stops flash- ing after the “ENGINE START STOP” switch has been turned to ACCESSORY or IGNITION ON mode to indicate that the system has been canceled.
Vehicles without navigation system
105
LC200_OM_OM60L09U_(U)
1-6. Theft deterrent system
■System maintenance
The vehicle has a maintenance-free type engine immobilizer system.
■Conditions that may cause the system to malfunction
●If the key is in contact with a metallic object. ●If the key is in close proximity to or touching a key to the security system
(key with a built-in transponder chip) of another vehicle.
■Certifications for the engine immobilizer system
FCC ID: NI4TMIMB-1