2007 Toyota Corolla Owners Manual

speed bumps. Also, do not at- tempt to go through an auto- matic car wash as the vehicle may get caught, resulting in damage.

the

distinctive

Compact spare tire The compact spare tire is designed for temporary emergency use only. The compact spare tire is identified by wording “TEMPORARY USE ONLY” molded into the side wall of the tire. The compact spare tire saves space in your luggage compartment, and its lighter weight helps to improve fuel economy and permits easier installa- tion in case of a flat tire.

218

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Required tools and spare tire

To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations.

tools and

1. Get the required

spare tire. 1. Wheel nut wrench 2. Jack handle 3. Tool holder 4. Jack 5. Spare tire

Turn the jack joint by hand. To remove: Turn the joint in direction 1 until the jack is free. To store: Turn the joint in direction 2
until the jack is firmly secured to pre- vent it flying forward during a collision or sudden braking.

219

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Blocking the wheel

When storing the spare tire, put it in place with the outer side of the wheel facing up. Then secure the tire by re- peating the above removal steps in reverse order to prevent it from flying forward during a collision or sudden braking.

To remove the spare tire: 1. Raise the luggage compartment

floor.

2. Take the tool holder with tools out. 3. Loosen the bolt with spacer and

remove it.

Then take the spare tire out of the vehicle.

220

2. Block the wheel diagonally op- posite the flat tire to keep the vehicle from rolling when it is jacked up.

When blocking the wheel, place a wheel block in front of one of the front wheels or behind one of the rear wheels.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Removing wheel ornament (steel wheels)

—Loosening wheel nuts

CAUTION

Never use oil or grease on the bolts or nuts. The nuts may loose and the wheels may fall off, which could cause a serious ac- cident.

3. Remove the wheel ornament. Pry off the wheel ornament, using the beveled end of the wheel nut wrench as shown.

CAUTION

Do not try to pull off the orna- ment by hand. Take due care in handling the ornament to avoid unexpected personal injury.

4. Loosen all the wheel nuts. Always loosen the wheel nuts before raising the vehicle. Turn the wheel nuts counterclockwise to loosen. To get maximum leverage, fit the wrench to the nut so that the handle is on the right side, as shown above. Grab the wrench near the end of the handle and pull up on the han- dle. Be careful that the wrench does not slip off the nut. Do not remove the nuts yet—just un- screw them about one−half turn.

221

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Positioning the jack

—Raising your vehicle

CAUTION

Never get under the vehicle when the vehicle is supported by the jack alone.

5. Position the jack at the correct

jack point as shown.

Make sure the jack is positioned on a level and solid place.

6. After making sure that no one is in the vehicle, raise it high enough so that the spare tire can be installed.

Remember you will need more ground clearance when putting on the spare tire than when removing the flat tire. To raise the vehicle, insert the jack handle into the jack (it is a loose fit) and turn it clockwise. As the jack touches the vehicle and begins to lift, double−check that it is properly posi- tioned.

222

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Changing wheels

—Reinstalling wheel nuts

7. Remove the wheel nuts and

change tires.

Lift the flat tire straight off and put it aside. Roll the spare wheel into position and align the holes in the wheel with the bolts. Then lift up the wheel and get at least the top bolt started through its hole. Wiggle the tire and press it back over the other bolts.

Before putting on wheels, remove any corrosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal−to−met- al contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving.

8. Reinstall all the wheel nuts fin-

ger tight.

Reinstall the wheel nuts (tapered end inward) and tighten them as much as you can by hand. Press back on the tire and see if you can tighten them more.

223

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

CAUTION

Never use oil or grease on the bolts or nuts. Doing so may lead to overtightening the nuts and damaging the bolts. The nuts may loose and the wheels may fall off, which could cause a seri- ous accident. If there is oil or grease on any bolt or nut, clean it.

’07 Corolla_U (L/O 0608)

—Lowering your vehicle

CAUTION

(cid:1) When

lowering the vehicle, make sure all portions of your body and all other persons around will not be injured as the vehicle is lowered to the ground.

(cid:1) Have the wheel nuts tightened by torque wrench at 103 N·m (10.5 kgf·m, 76 ft·lbf), as soon as possible after changing wheels. Otherwise, the nuts may loosen and the wheels may fall off, which could cause a serious accident.

(cid:1) Do not attach a heavily dam- aged plastic wheel ornament. It may fly off the wheel and cause accidents while the ve- hicle is moving.

9. Lower the vehicle completely

and tighten the wheel nuts.

Turn the jack handle counterclock- wise to lower the vehicle. Use only the wheel nut wrench to tighten the nuts. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. Make sure the wrench is securely engaged over the nut. Tighten each nut a little at a time in the order shown. Repeat the process until all the nuts are tight.

224

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Reinstalling wheel ornament (steel wheels)

CAUTION

Take due care in handling the or- nament to avoid unexpected per- sonal injury.

10.Reinstall the wheel ornament. 1. Put the wheel ornament into posi-

tion.

Align the cutout of the wheel orna- ment with the valve stem as shown. 2. Press hand firmly on one side of wheel ornament and then firmly tap the other side around the edge of wheel ornament with the heel of your hand to snap into place.

—After changing wheels 11. Check the air pressure of the re-

placed tire.

Adjust the air pressure to the specifi- cation designed on page 284 in Sec- tion 8. If the pressure is lower, drive slowly to the nearest service station and fill to the correct pressure. Do not forget to reinstall the tire infla- tion valve cap as dirt and moisture could get into the valve core and possibly cause air leakage. If the cap is missing, have a new one put on as soon as possible. 12.Restow all the tools, jack and

flat tire securely.

As soon after changing wheels as possible, tighten the wheel nuts to the torque specified on page 284 in Sec- tion 8 with a torque wrench. Have a technician repair the flat tire and re- place the spare tire with it. Initial adjustment of the tire pres- sure warning system is necessary after you have replaced your tires or wheels. See “Tire pressure warning system” on page 124 in Section 1−7.

225

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

CAUTION

Before driving, make sure all the tools, jack and flat tire are se- curely in place in their storage location to reduce the possibility of personal injury during a colli- sion or sudden braking.

’07 Corolla_U (L/O 0608)

If your vehicle becomes stuck If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward. Vehicles with traction control system— Turn off the traction control system to become unstuck to allow the tires to spin enough to remove the vehicle from the obstruction. (For details, see “Trac- tion control system” on page 120 in Section 1−7.)

CAUTION

Do not attempt to rock the vehicle free by moving it forward and back- ward if people or objects are any- where near the vehicle. During the rocking operation the vehicle may suddenly move forward or backward as it becomes unstuck, causing injury or damage to nearby people or ob- jects.

NOTICE

If you rock your vehicle, observe the following precautions to prevent dam- age to the transmission and other parts. (cid:1) Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.

(cid:1) Do not race the engine and avoid

spinning the wheels.

(cid:1) If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.

226

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

If your vehicle needs to be towed—

(a) Towing with wheel lift type truck—

—From front

—From rear

(b) Using flat bed truck

’07 Corolla_U (L/O 0608)

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. In consultation with them, have your vehicle towed using either (a) or (b). Only when you cannot receive a towing service from a Toyota dealer or com- mercial tow truck service, tow your ve- hicle carefully in accordance with the instructions given in “—Emergency tow- ing” on page 228 in this Section. Proper equipment will help ensure that your vehicle is not damaged while being towed. Commercial operators are generally aware of local laws pertaining to towing. Your vehicle can be damaged is towed incorrectly. Although most operators know the correct procedure, it is possible to make a mistake. To avoid damage to your vehicle, make sure the following pre- cautions are observed. If necessary, show this page to the tow truck driver. TOWING PRECAUTIONS: Use a safety chain system for all towing, and abide by the state/provincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly.

the state/provincial and

it

if

(a) Towing with wheel lift type truck From front—Release the parking brake.

NOTICE

When lifting wheels, take care to en- sure adequate ground clearance for towing at the opposite end of the raised vehicle. Otherwise, the bumper and/or underbody of the towed vehicle will be damaged during towing.

From rear— (cid:1) Manual transmission:

We recommend using a towing dolly under the front wheels. If you do not use a towing dolly, place the ignition key in the “ACC” position and put the transmission in neutral.

NOTICE

Do not tow with the key removed or in the “LOCK” position when towing from the rear without a towing dolly. The steering lock mechanism is not strong enough to hold the front wheels straight.

227

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Emergency towing

(cid:1) Automatic transmission:

Use a wheels.

towing dolly under

the

front

(c) Towing with sling type

truck

NOTICE

Never tow a vehicle with an automatic transmission from the rear with the front wheels on the ground, as this may cause serious damage to the transmission.

(b) Using flat bed truck

(c) Towing with sling type truck

NOTICE

Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage.

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. If towing service is not available in an emergency, your vehicle may be tempo- rarily towed by a cable or chain se- cured to the emergency towing eyelet under the vehicle. Use extreme caution when towing vehicles.

NOTICE

Only use specified towing eyelet; otherwise your vehicle may be dam- aged.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

228

A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard−surfaced roads for a short dis- tance and at the wheels, axles, drive train, steering and brakes must all be in good condition.

low speeds. Also,

CAUTION

Use extreme caution when towing ve- hicles. Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing eyelet and towing cable or chain. The eyelet and towing cable or chain may break and cause serious injury or damage.

NOTICE

Use only a cable or chain specifically intended for use in towing vehicles. Securely fasten the cable or chain to the towing eyelet provided.

’07 Corolla_U (L/O 0608)

If you cannot shift automatic transmission selector lever

Before towing, release the parking brake and put the transmission in neutral (manu- al) or “N” (automatic). The key must be in “ACC” (engine off) or “ON” (engine run- ning).

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

though

If you cannot shift the selector lever out of “P” position to other positions even is de- pressed, use the shift lock override but- ton as follows: 1. Turn

the brake pedal

ignition key

the

to “LOCK” the parking

position. Make sure brake is applied.

2. Pry up the cover with a flathead

screwdriver or equivalent.

229

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

If you lose your keys You can purchase a new key at your Toyota dealer if you can give them the key number and master key. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- lizer system must be replaced. See page 10 in Section 1−2. If your keys are locked in the vehicle and you cannot get a duplicate, many Toyota dealers can still open the door for you, using If you must break a window in, we suggest breaking the smallest side window be- cause it is the least expensive to replace. Be extremely cautious to avoid cuts from the glass.

the suggestion given in “Keys” on

their special

to get

tools.

If you lose your wireless remote control transmitter You can purchase a new wireless re- mote control transmitter at your Toyota dealer. Have the registered identification numbers of your transmitters deleted from your ve- hicle by your Toyota dealer as soon as possible to avoid the possibility of theft or an accident. Then, have the identification number of your new transmitter registered. At the same time, you must bring all of the remaining transmitters to have them registered again as well. You can use the wireless remote control system with the new transmitter. Contact your Toyota dealer for detailed information.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

3. Insert your finger into the hole to push down the shift lock override button. You can shift out of “P” position only while pushing the but- ton.

4. Shift into “N” position. 5. Insert the cover. 6. Start the engine. For your safety,

keep the brake pedal depressed.

Be sure to have the system checked by your Toyota dealer as soon as possible.

230

’07 Corolla_U (L/O 0608)

SECTION 5

CORROSION PREVENTION AND APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosion Washing and waxing your Toyota Cleaning the interior

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

232
233
235

231

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Protecting your Toyota from corrosion Toyota, through the diligent research, de- sign and use of the most advanced technology available, helps prevent corro- sion and provides you with the finest qual- ity vehicle construction. Now, it is up to you. Proper care of your Toyota can help ensure long−term corrosion prevention. The most common causes of corrosion to your vehicle are: (cid:1) The accumulation of road salt, dirt and moisture in hard−to−reach areas under the vehicle.

(cid:1) Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.

Care is especially important if you live in particular areas or operate your ve- hicle under certain environmental condi- tions: (cid:1) Road salt or dust control chemicals will accelerate corrosion, as will the pres- ence of salt in the air near the sea− coast or in areas of industrial pollution. (cid:1) High humidity accelerates corrosion es- pecially when temperatures range just above the freezing point.

232

’07 Corolla_U (L/O 0608)

(cid:1) Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry.

(cid:1) High ambient temperatures can cause corrosion to those components of the vehicle which do not dry quickly due to lack of proper ventilation.

The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any dam- age to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your vehicle frequently. It is, of course, necessary to keep your vehicle clean by regular washing, but to prevent corrosion, the following points should be observed: (cid:1) If you drive on salted roads

the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize cor- rosion.

in

(cid:1) High pressure water or steam is effec- tive for cleaning the vehicle’s underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as trapped water in these areas can cause corrosion.

(cid:1) Wash the underside of the vehicle thor-

oughly when winter is over.

See “Washing and waxing your Toyota” on page 233 for more tips. Check the condition of your vehicle’s paint and trim. If you find any chips or scratches in the paint, touch them up im- mediately to prevent corrosion from start- ing. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Check the interior of your vehicle. Wa- ter and dirt can accumulate under the floor mats and could cause corrosion. Oc- casionally check under the mats to make sure the area is dry. Be particularly care- ful when transporting chemicals, cleans- ers, fertilizers, salt, etc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your vehicle. Full−size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your Toyota dealer will be happy to assist in supplying and installing the shields if they are recommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly venti- lated garage. If you wash your vehicle in the garage, or if you drive it covered with water or snow, your garage may be so damp as to cause corrosion. Even if your garage is heated, a wet vehicle can cor- rode if the ventilation is poor.

Washing and waxing your Toyota Washing your Toyota Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as pos- sible. (cid:1) When driving in a coastal area (cid:1) When driving on a road sprinkled with

antifreeze

(cid:1) When exposed to coal tar, tree sap, bird droppings and carcass of an insect (cid:1) When driving in areas where there is a lot of smoke, soot, dust, iron dust or chemical substances

(cid:1) When the vehicle becomes remarkably

dirty with dust and mud Hand−washing your Toyota Work in the shade and wait until the vehicle body is not warm to the touch.

CAUTION

(cid:1) When cleaning under floor or chas- sis, be careful not to injure your hands.

(cid:1) Exhaust gases cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot ex- haust pipe can cause burns.

1. Rinse off loose dirt with a hose. Re- move any mud or road salt from the underside of the vehicle or the wheel wells.

2. Wash with a mild car−wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt.

Fuel filler door: Do not apply water (high− pressure car wash, for example) at or near the fuel tank inlet with the fuel filler door opened. If the water enters the air vent, you may experience trouble with re- fueling or rough engine idling. Plastic wheel ornaments: The plastic wheel ornaments are damaged easily by organic substances. If any organic sub- stances splash an ornament, be sure to wash them off with water and check if the ornament is damaged.

233

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Aluminum wheels: Use only a mild soap or neutral detergent. Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft. Exterior lights: Wash carefully. Do not use organic substances or scrub them with a hard brush. This may damage the sur- faces of the lights. Road turpentine or cleaners that are marked safe for painted surfaces. 3. Rinse

can cause streaking. In hot weather you may need to rinse each section right after you wash it.

tar: Remove with

thoroughly—dried

soap

4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.

234

’07 Corolla_U (L/O 0608)

NOTICE

(cid:1) Do not use organic substances (gasoline, kerosene, benzine or strong solvents), which may be tox- ic or cause damage.

(cid:1) Do not scrub any part of the ve- hicle with a hard brush, which may cause damage.

Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some types of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle.

NOTICE

To prevent damage to the antenna, make sure it is removed before driv- ing your Toyota through an automatic car wash.

Waxing your Toyota Polishing and waxing is recommended to maintain the original beauty of your Toyota’s finish. Apply wax once a month or if the vehicle surface does not repel water well. 1. Always wash and dry the vehicle be- fore you begin waxing, even if you are using a combined cleaner and wax.

2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car−cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint. Windshield washer nozzles: Make sure that the nozzles do not become blocked If a nozzle becomes when waxing. blocked, contact your Toyota dealer to have the vehicle serviced.

NOTICE

If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Exterior lights: Do not apply wax on the surfaces of the lights. Wax may cause damage to the lenses. If you accidentally put wax on the light surfaces, wipe or wash it off. 3. Wax

the vehicle again when water does not bead but remains on the sur- face in large patches.

Cleaning the interior

CAUTION

(cid:1) Vehicles with side airbags and cur-

tain shield airbags: Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags from acti- vating correctly, resulting in serious injury.

(cid:1) Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interior or exterior. Water may get into audio components or other electrical components above or un- der the floor carpet (or mat) and cause a malfunction; and it may cause body corrosion.

Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming− type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.

NOTICE

Do not use solvent, thinner, gasoline or window cleaner on the interior.

235

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

to

foam−type shampoo

Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol cans and others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.

NOTICE

(cid:1) Do not use dye or bleach on the

belts—it may weaken them.

(cid:1) Do not use the belts until they be-

come dry.

236

’07 Corolla_U (L/O 0608)

(cid:1) If you use a liquid car freshener, do not spill the liquid onto the ve- hicle’s interior surfaces. It may con- tain the ingredients mentioned above. Immediately clean any spill using the method mentioned above.

Leather interior The leather upholstery may be cleaned with neutral detergent for wool. Remove dirt using a soft cloth dampened with 5% solution of neutral detergent for wool. Then thoroughly wipe off all traces of detergent with a clean damp cloth. After cleaning or whenever any part of the leather gets wet, dry with a soft clean cloth. Allow the leather to dry in a venti- lated shaded area.

Windows The windows may be cleaned with any household window cleaner.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

Air conditioning control panel, audio panel, instrument panel, console panel, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly wipe off dirt.

NOTICE

(cid:1) Do not use organic substances (sol- vents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.

(cid:1) If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

(cid:1) The interior of your vehicle is apt to heat up on hot summer days, so avoid placing on the upholstery items made of vinyl or plastic or containing wax as these tend to stick to leather when warm.

(cid:1) Improper cleaning of the leather up- holstery could result in discolor- ation or staining.

If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them.

NOTICE

(cid:1) If a stain should fail to come out with a neutral detergent, apply a cleaner that does not contain an organic solvent.

(cid:1) Never use organic substances such as benzine, alcohol or gasoline, or alkaline or acid solutions for clean- ing the leather as these could cause discoloring.

(cid:1) Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather. (cid:1) Mildew may develop on soiled leath- er upholstery. Be especially careful to avoid oil spots. Try to keep your upholstery always clean.

(cid:1) Long exposure to direct sunlight may cause the leather surface to harden and shrink. Keep your ve- hicle in a shaded area, especially in the summer.

237

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

238

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

SECTION 6

VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirements General maintenance Does your vehicle need repairing? Emissions Inspection and Maintenance (I/M) programs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

240
241
243
244

For scheduled maintenance the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

information, please refer

to

239

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Maintenance requirements Your Toyota vehicle has been designed for fewer maintenance requirements with long- er service intervals to save both your time and money. However, each regular mainte- nance, as well as day−to−day care, is more important than ever before to ensure smooth, trouble−free, safe, and economical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note that both the new vehicle and emis- sion control system warranties specify that proper maintenance and care must be per- formed. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for complete warranty information. General maintenance General maintenance items are those day− to−day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to insure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your Toyota dealer will be pleased to do them at a nominal cost.

240

Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non−Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may also elect to have mainte- nance, replacement, or repair of the emission control devices and system performed by any automotive repair es- tablishment or individual without invali- dating this warranty. See “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement” for complete war- ranty information.

for

Where to go for service? Toyota technicians are well−trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in−dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. If any prob- lems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota. What about do−it−yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented on page 245 in Section 7.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

If you are a skilled do−it−yourself mechan- ic, the Toyota service manuals are recom- mended. Please be aware that do−it−your- self maintenance can affect your warranty coverage. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for the details.

’07 Corolla_U (L/O 0608)

the

items

listed,

General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.

CAUTION

Make these checks only with ade- quate ventilation if you run the en- gine.

IN THE ENGINE COMPARTMENT Items listed below should be checked from time to time, e.g. each time when refueling. Washer fluid Make sure there is sufficient fluid in the tank. See page 271 in Section 7−3 for additional information.

Engine coolant level Make sure the coolant level is between the “FULL” and “LOW” lines on the see− through reservoir when the engine is cold. See page 256 in Section 7−2 for addition- al information. Radiator, condenser and hoses Check that the front of the radiator and condenser are clean and not blocked with leaves, dirt, or insects. See page 257 in Section 7−2 for additional information. Battery condition Check the battery condition by the indica- tor color. See page 268 in Section 7−3 for additional information. Brake fluid level Make sure the brake fluid level is correct. See page 257 in Section 7−2 for addition- al information. Engine oil level Check the level on the dipstick with the engine turned off and the vehicle parked on a level spot. See page 254 in Section 7−2 for additional information. Power steering fluid level Check the level through the reservoir. The level should be in the “HOT” or “COLD” range depending on the fluid temperature. See page 258 in Section 7−2 for addition- al information.

241

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. (See “Engine exhaust cautions” on page 176 in Section 2.) INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc. Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Check headlight aim. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Be alert for changes in steering condition, such as hard steering or strange noise.

242

the

that

Seats Check that all front seat controls such as seat adjusters, seatback recliner, etc. op- erate smoothly and that all latches lock securely in any position. Check that the head restraints move up and down smoothly and that the locks hold securely in any latched position. For folding−down rear seatbacks, check latches lock securely. Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure that the belt webbings are not cut, frayed, worn or damaged. Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Clutch pedal Check the pedal for smooth operation. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function. Brakes In a safe place, check that the brakes do not pull to one side when applied.

Parking brake Check that the lever has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Automatic transmission “Park” mecha- nism Check the lock release button of the se- lector lever for proper and smooth opera- tion. On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes re- leased. OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately.

fluid after

time

to

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Doors and engine hood Check that all doors including trunk lid operate smoothly and all latches lock se- curely. Make sure the engine hood sec- ondary latch secures the hood from open- ing when the primary latch is released. Tire inflation pressure Check the pressure with a gauge ev- ery two weeks, or at least once a month. See page 259 in Section 7−2
for additional information. Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See page 261 in Section 7−2 for additional in- formation. When checking the tires, make sure no nuts are missing, and check the nuts for looseness. Tighten them if necessary. Tire rotation Rotate the tires according to the maintenance schedule. (For sched- uled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.) See page 263 in Section 7−2
for additional information.

’07 Corolla_U (L/O 0608)

tip−offs

for changes

Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: (cid:1) Engine missing, stumbling, or pinging (cid:1) Appreciable loss of power (cid:1) Strange engine noises (cid:1) A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)

If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair.

CAUTION

Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.

(cid:1) Change

in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)

(cid:1) Flat−looking tire; excessive tire squeal

when cornering; uneven tire wear

(cid:1) Vehicle pulls to one side when driving

straight on a level road

(cid:1) Strange noises related to suspension

movement

(cid:1) Loss of brake effectiveness; spongy feeling brake or clutch pedal; pedal al- most touches floor; vehicle pulls to one side when braking

(cid:1) Engine coolant temperature continually

higher than normal

243

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Also, if the malfunction indicator lamp had come on recently due to temporary mal- function such as a loose fuel tank cap, your vehicle may not pass the I/M test. The malfunction indicator lamp will go off after taking several driving trips, but the error code in the OBD system will not be cleared unless about 40 trips or more are taken. If your vehicle does not pass the I/M test even the malfunction indicator lamp does not come on, contact your Toyota dealer to prepare the vehicle for re−testing.

indicator

the malfunction

in- include OBD

Emissions Inspection and Maintenance (I/M) programs Some states have vehicle emission spection programs which (On−Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. When the OBD system determines that a problem exists somewhere in the emission control system, lamp comes on. In this case, your vehicle may the I/M test and need to be not pass repaired. Contact your Toyota dealer to service the vehicle. Even lamp does not come on, your vehicle may not pass readiness codes have not been set in the OBD system. Readiness codes are automatically set during ordinary driving. However, when the battery is disconnected or run down, the codes are erased. Also, depending on your driving habits, the codes may not be completely set.

the malfunction

indicator

test as

I/M

the

if

244

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

SECTION 8

SPECIFICATIONS Specifications Dimensions and weights Engine Fuel Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

280
280
281
281
284
284

279

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Dimensions and weights

Overall length

Overall width Overall height*

Wheelbase

Front tread

Rear tread

Vehicle capacity weight (occupants + luggage)

Towing capacity (trailer weight + cargo weight) * : Unladen vehicle

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

kg (lb.)

kg (lb.)

4530 (178.3)

1700

(66.9)

1480

(58.3)

2600 (102.4)

1480

(58.3)

1460

(57.5)

385

(850)

680 (1500)

Engine Model:

1ZZ−FE

Type:

4 cylinder in line, 4 cycle, gasoline

Bore and stroke, mm (in.):

79.0 (cid:1) 91.5 (3.11 (cid:1) 3.60)

Displacement, cm3 (cu. in.):

1794 (109.5)

280

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Fuel Fuel type:

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher

Fuel tank capacity, L (gal., Imp. gal.):

50 (13.2, 11.0)

Service specifications ENGINE Valve clearance (engine cold), mm (in.):

Intake Exhaust

0.15—0.25 (0.006—0.010) 0.25—0.35 (0.010—0.014)

Spark plug type:

DENSO NGK

SK16R11
IFR5A11
Spark plug gap, mm(in.):

1.1 (0.043)

ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):

With filter Without filter

4.2 (4.4, 3.7) 4.0 (4.2, 3.5) “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

is used

satisfy

the

ILSAC multigrade engine oil is recom- mended.

281

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Recommended oil viscosity:

SAE 5W−30

Outside temperature

Please contact your Toyota dealer for fur- ther details.

COOLING SYSTEM Total capacity, L (qt., Imp. qt.):

6.5 (6.9, 5.7)

Coolant type:

“Toyota Super Long Life Coolant” is used in your Toyota vehicle at factory fill. In order to avoid technical problems, only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life hybrid organic acid technology. (Coolant with long−life hybrid organic acid technology is a combination of low phosphates and organic acids.) Do not use plain water alone. Please contact your Toyota dealer for further details.

BATTERY Open voltage* at 20(cid:1)C (68(cid:1)F):

12.6—12.8 V 12.2—12.4 V 11.8—12.0 V

Fully charged Half charged Discharged

* : Voltage that is checked 20 minutes af- the

is removed with all

the key

ter lights turned off.

Charging rates:

5 A max.

CLUTCH Pedal free play, mm (in.):

5—15 (0.2—0.6)

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

MANUAL TRANSAXLE Oil capacity, L (qt., Imp. qt.):

1.9 (2.0, 1.7)

Oil type:

Gear oil API GL−4 or GL−5

Recommended oil viscosity:

SAE 75W−90

282

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

AUTOMATIC TRANSAXLE Fluid capacity (drain and refill), L (qt., Imp. qt.):

Up to 3.0 (3.2, 2.6)

Fluid type:

Toyota Genuine ATF Type T−IV

in

listed

Guide”

is necessary

Change automatic transmission fluid only as necessary. Generally, to change it automatic transmission fluid only if your vehicle is driven under one of the Special Operating Conditions your “Scheduled Maintenance or “Owner’s Manual Supplement”. When changing the automatic transmission fluid, use only “Toyota Genuine ATF Type T−IV” to aid (ATF JWS3309 or NWS6500) in assuring optimum transaxle performance. Notice: Using automatic transmission fluid other than “Toyota Genuine ATF Type T−IV” may cause deterioration in shift quality, locking up of your trans- mission accompanied by vibration, and ultimately damage the automatic trans- mission of your vehicle. Please contact your Toyota dealer for fur- ther details.

’07 Corolla_U (L/O 0608)

BRAKES Minimum pedal clearance when depressed with the force of 294 N (30 kgf, 66 lbf) with the engine running, mm (in.):

With anti−lock brake system Without anti−lock brake system

76 (2.99)

78 (3.07)

Pedal free play, mm (in.):

1—6 (0.04—0.24)

Pad wear limit, mm (in.):

1.0 (0.04)

Lining wear limit, mm (in.):

1.0 (0.04)

Parking brake adjustment when pulled with the force of 196 N (20 kgf, 44 lbf):

6—9 clicks

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

STEERING Wheel free play:

Less than 30 mm (1.2 in.)

Power steering fluid type:

Automatic transmission fluid DEXRON(cid:2)II or III

283

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Tires Tire size and cold tire inflation pressure: Front and rear

kPa (kgf/cm2 or bar, psi)

Fuses

Tire size

Front

Rear

P185/65R15 86S P195/65R15 89S 195/55R16 87V

Spare

210 (2.1, 30) 210 (2.1, 30) 220 (2.2, 32)

210 (2.1, 30) 210 (2.1, 30) 220 (2.2, 32) kPa (kgf/cm2 or bar, psi)

T125/70R16 96M Wheel nut torque, N·m (kgf·m, ft·lbf):

420 (4.2, 60)

103 (10.5, 76)

Wheel size 15 (cid:1) 6 JJ 15 (cid:1) 6 JJ 16 (cid:1) 6 JJ

Wheel size 16 (cid:1) 4T

NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire inflation pressure” through “Aluminum wheel precautions”, pages 259 through 266, in Section 7−2.

284

Engine compartment

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

8. AMP 30 A: Audio system 9. MAIN 30 A: Starting system, “AM2”

fuse

10. DOME 15 A: Audio system, clock, per- sonal lights, interior light, trunk light, open door warning light, wireless re- mote control system

11. HORN 10 A: Horn 12. HAZARD 10 A: Emergency

flashers,

turn signal lights

13. EFI 20 A: Multiport fuel injection sys- injection system,

tem/sequential multiport system, “EFI2” fuse

fuel control

emission

14. ALT−S 5 A: Charging system 15. HEAD LH LWR 10 A: Left−hand head-

light (low beam)

16. HEAD RH LWR 10 A: Right−hand

headlight (low beam)

17. EFI2 15 A: Multiport fuel injection sys- tem/ sequential multiport fuel injection system, emission control system

18. TAIL 15 A: Tail

lights, instrument panel

lights, ment cluster lights

license plate lights, instru-

19. OBD 7.5 A: On−board diagnosis sys-

tem

20. P/W 30 A: No circuit 21. WIPER 25 A: Windshield wipers 22. AM2 15 A: Charging system, multiport fuel injection system/sequential multi- port fuel injection system, starting sys- tem, SRS airbag system

23. STOP 15 A: Stop lights, high mounted stoplight, anti−lock brake system, shift lock control system, multiport fuel in- jection system/sequential multiport fuel injection system, cruise control system 24. DOOR 25 A: Power door lock system 25. AM1 25 A: “CIG” fuse 26. ECU−IG 10 A: Electric cooling

fan, anti−lock brake system, vehicle stability control system, traction control system, brake assist system, shift lock control system, cruise control system

27. RR WIPER 15 A: No circuit 28. A/C 10 A: Air conditioning system 29. INV 15 A: No circuit 30. P/POINT 15 A: Power outlet (in the

rear console box)

31. ECU−B 10 A: Daytime running

light

system

285

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Instrument panel

Fuses (type A) 1. FOG 15 A: Front fog lights 2. HEAD LH UPR 10 A: Left−hand head-

light (high beam)

3. HEAD RH UPR 10 A: Right−hand headlight (high beam), high beam indi- cator light

4. SPARE 30 A: Spare fuse 5. SPARE 15 A: Spare fuse 6. SPARE 10 A: Spare fuse 7. ETCS 10 A: Electronic throttle control

system

’07 Corolla_U (L/O 0608)

39. HEAD MAIN 40 A: “HEAD LH UPR”, “HEAD RH UPR”, “HEAD LH LWR” and “HEAD RH LWR” fuses

40. HTR 40 A: Air conditioning system 41. DEF 40 A: Rear window defogger,

“M−HTR/DEF I−UP” fuse

42. POWER 30 A: Power windows, electric

moon roof

Fuse (type C) 43. ALT 100 A: Charging system, “ABS NO.1”, “ABS NO.2”, “RDI FAN”, “FOG”, “HTR”, “DOOR”, “ECU−B”, “TAIL”, “STOP”, “P/POINT”, “INV” and “OBD” fuses

“POWER”,

“AM1”,

32. CIG 15 A: Power outlet (on the instru- ment panel) or cigarette lighter, audio system, clock, power rear view mirror control, shift lock control system

33. GAUGE 10 A: Gauges and meters, air conditioning system, daytime running light system, charging system, auto anti−glare inside rear view mirror, pow- er windows, cruise control system, rear window defogger, back−up lights, front passenger’s seat belt reminder light 34. WASHER 15 A: Windshield washer 35. M−HTR/DEF I−UP 10 A: Engine control

system

Fuses (type B) 36. ABS NO.1 30 A: Anti−lock brake sys- tem, vehicle stability control system, traction control system, brake assist system

37. RDI FAN 30 A: Electric cooling fan 38. ABS NO.2 40 A (without vehicle sta- bility control system): Anti−lock brake system ABS NO.2 50 A (with vehicle stability control system): Anti−lock brake sys- tem, vehicle stability control system, traction control system, brake assist system

286

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

SECTION 9

REPORTING SAFETY DEFECTS FOR U.S. OWNERS Reporting safety defects for U.S. owners Reporting safety defects for U.S. owners

. . . . . . . . . . . . . . . . . . . . . .

288

287

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Safety Hotline

the To contact NHTSA, you may call Vehicle at toll−free 1−888−327−4236 (TTY: 1−800−424−9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also information about motor obtain other vehicle from http://www.safercar.gov.

safety

Reporting safety defects for U.S. owners If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately in- form the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll−free: 1−800−331−4331). If NHTSA receives similar com- plaints, it may open an investiga- tion, and if it finds that a safety defect exists in a group of ve- hicles, it may order a recall and remedy However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.

campaign.

288

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

SECTION 1− 1

OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview Instrument cluster overview Indicator symbols on the instrument panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Instrument panel overview

1. Side defroster outlets 2. Side vents 3. Instrument cluster 4. Center vents 5. Electric moon roof switches 6. Personal lights 7. Power door lock switches 8. Power window switches 9. Glove box 10. Portable ashtray 11. Rear console box 12. Cup holders 13. Power outlet 14. Parking brake lever 15. Automatic transmission selector lever

or manual transmission gear shift lever

16. Hood lock release lever 17. Window lock switch

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

1. Headlight, turn signal and front fog

light switches

2. Wiper and washer switches 3. Emergency flasher switch 4. Audio system 5. Clock 6. Front passenger occupant classification

indicator light/front passenger’s seat belt reminder light

7. Rear window defogger switch 8. Auxiliary boxes 9. “TRAC OFF” (traction control system

off) switch

10. Power outlet or cigarette lighter 11. Air conditioning controls 12. Ignition switch 13. Cruise control switch 14. Tilt steering lock release lever 15. Instrument panel light control dial 16. Power rear view mirror control switches 17. Tire pressure warning system reset

switch

18. Engine immobilizer system/Toyota vehicle intrusion protection system indicator light

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)